A-Type Coalescer Element

COALESCER ELEMENT
For the Separation of Water and Solids from Hydrocarbons
Filter water separators are fitted with coalescer and separator elements at various places
to separate water and dirt from Hydrocarbons. They are also used in mobile refuelling
units and fixed fuelling installations and tank farms. FAUDI Aviation coalescers are com-
monly used at all kind of branches in the industry such as refineries, petrochemical
plants and marine applications where high efficiency filtration and separation is required.
Range of use:
- Mainly in refineries for filtering intermediate products
- On ships
- At ship unloading terminals for water separation and filtration of diesel fuels

Technical Details
Nominal Filtration: 10μm
max. Differential Pressure: 1,1 bar (15 psi)
Burst Pressure: 5.2 bar (75 psi)
Recommended Service time: 24 Monate1
Recommended Storage time: 24 Monate1&2
max. operating Temperature: min. -30°C / max. 80°C
Flow Direction: Innen nach außen
Outside Diameter: 152 mm (6”)
1
Manufacturer recommendation
2
Original packaging, 20°C and max. 50% humidity
acc. dispatching date out of FAUDI Aviation stock

Standard Design
■ Inner tube in epoxy coated steel
■ Seals in Viton®
■ Endcaps made out of Polyamid/reinforced glass fibre

Coalescer wrap

Pleated paper/
filtration section

Support tube

Cotton outer sock

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-A-Coalescer-EN_2.0 Page 1/2 Rev. 2.0
 A-Type Coalescer Element
COALESCER ELEMENT
Sample of Marking

Sample of marking:
A.1-842/1
Model Type Additional Feature

Endcap Design Nominal Length in mm

Additional Feature
- Limited solvent-resistance
1 - Endcap adhesive and longitudinal seam in epoxy
- End Caps and support tube in stainless steel
Ø50 (2“)

Ø50 (2“) Ø65 (29/16“) Ø89 (31/2“)

L
L

Ø30

Ø152 (6“) Ø152 (6“) Ø152 (6“) Ø152 (6“)

Model 1 Model 3 Model 4 Model 6

Nominal lenght L
(including sealing)
mm inch Model 1 Model 3 Model 4 Model 6
473 18 5/8 A.6-467
565 22 1/4
A.1-559
733 28 7/8
A.4-727
848 33 3/8
A.1-842 A.3-842 A.4-842 A.6-842

Torques
34 Nm (for spindle) 22 Nm

Flat sealed
Version 1, 3 & 4

Torques Conversation Table

ft/lbs inch/lbs kg/m Nm
17 200 2,30 22
20 240 2,80 27
25 300 3,50 34

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-A-Coalescer-EN_2.0 Page 2/2 Rev. 2.0
D-Type Coalescer Element

COALESCER ELEMENT
For separation of water and solids from aviation fuels according to
TL 4330-0001 (Part 1 & 2), Mil-F-8901E and AM+M 537 B.
Filter water separators are fitted with coalescer and separator elements and used on air-
craft refuelling vehicles, hydrant dispensers and other mobile fuelling equipment. They
are also used in fixed fuelling installations and tank farms. FAUDI Aviation coalescers are
commonly used in other branches of industry such as refineries, petrochemical plants
and marine applications where high efficiency filtration and separation is required.

Technical Details
Tested and approved to spec. TL 4330-0001 (Part 1 & 2), MIL-F 8901E & AM+M 537B
Nominal Filtration: 1μm
Change out differential pressure: 1.1 bar (15 psi)
Burst pressure: 5.2 bar (75 psi)
Recommended Service time: 24 months1
Recommended Storage time: 24 months1&2
OperatingTemperature: min. -30°C / max. 80°C
Flow direction: In to out
Outside diameter: 152 mm (6”)
1
Manufacturer recommendation
2
Original packaging, 20°C and max. 50% humidity
acc. dispatching date out of FAUDI Aviation stock

Standard Design

■ Inner tube in epoxy coated steel

■ Seals in NBR (Buna-N®)
■ Endcaps made out of Polyamid/reinforced glass fibre
■ Labeling according to EI (date of manufacturer,
ID-Number etc.) on the endcap

Coalescer wrap

Pleated paper
filtration section

Support tube

Cotton outer sock

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-D-Coalescer-EN_2.0 Page 1/2 Rev. 2.0
 D-Type Coalescer Element
COALESCER ELEMENT
Sample of Marking

Sample of marking:
D.1-842
Model Type

Endcap Design Nominal Length in mm

Ø50 (2“)

Ø50 (2“)

L
L

Ø30

Ø152 (6“) Ø152 (6“)

Endcap Design 1 Endcap Design 6

Model 1 (Open-end) Model 6 (O-Ring)

Nominal lenght L
(including sealing) Nominal lenght L
Model Type mm inch mm inch
D.1-362 368 14 1/2

D.1-842 848 333/8

D.6-467 467 18

Torques
34 Nm (for center rod) 22 Nm

Flat sealed
endcap design 1

Torques Conversation Table

ft/lbs inch/lbs kg/m Nm
17 200 2,30 22
20 240 2,80 27
25 300 3,50 34

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-D-Coalescer-EN_2.0 2/2 Rev. 2.0
DC-Type Coalescer Element

COALESCER ELEMENT
For the Separation of Water and Solids from Hydrocarbons
Filter water separators are fitted with coalescer and separator elements at various places
to separate water and dirt from Hydrocarbons. They are used in mobile and fixed fuelling
installations and tank farms. FAUDI Aviation coalescers are commonly used at all kind
of branches in the industry such as refineries, petrochemical plants and marine applica-
tions where high efficiency filtration and separation is required.

Technical Details
Nominal Filtration: 5, 10 & 25μm
Change-out Differential Pressure: 1.1 bar (15 psi)
Test- /Berst Pressure: 5.2 bar (75 psi)
Recommended Storage Time (max.): 24 months1&2
Operating Temperature: min. -30°C / max. 80°C
Flow Direction: In to Out
Outside Diameter: 152 mm (6”)
1
Manufacturer recommendation
2
Original packaging, 20°C and max. 50% humidity
after date of shipment out of stock of FAUDI Aviation GmbH

Standard Design
■ Inner tube in epoxy coated steel
■ Seals in NBR (Buna-N)
■ End caps made cut of polyamid/reinforced glas fibre
■ Labeling of end caps acc. to EI specification
(date of manufacturing, ID-Number, etc.)

Coalescer wrap

Pleated paper
filtration section

Support tube

Cotton outer sock

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-DC-Coalescer-EN_2.0 Page 1/2 Rev. 2.0
 DC-Type Coalescer Element
COALESCER ELEMENT
Sample of Marking

Article code:
DC.4-1093-25
Model Type Nominal micron rating

Endcap design Nominal lenght in mm

25 (1“)
1/2“ - 13 UNC
Ø50 (2“) Ø89 (31/2“)
L

L
Ø105 (49/64“)

Ø152 (6“) Ø152 (6“) Ø152 (6“)

Endcap Design Endcap Design Endcap Design

1 4 7

Flat Sealed Screw Based

Nominal lenght L
(Incl. seal) Endcap Design Nominal lenght L Endcap Design
mm inch 1 4 mm inch 7
285 11 1/4
DC.4-279-xx
369 14 1/2
DC.4-362-xx 351 14 13/16 DC.7-362-xx
565 22 1/4 DC.4-559-xx 565 22 1/4 DC.7-559-xx
733 28 7/8
DC.4-727-xx 705 27 3/4
DC.7-727-xx
848 33 3/8
DC.1-842-xx DC.4-842-xx 834 32 7/8
DC.7-842-xx
1099 43 1/4
DC.4-1093-xx 1114 43 7/8
DC.7-1093-xx
1428 56 1/4
DC.4-1422-xx 1418 56 7/8
DC.7-1422-xx

Torques
34 Nm (for center rod) 22 Nm

Flat Sealed
Endcap Design 1 & 4

22 Nm 27 Nm

Screw Based
Endcap Design 7
Conversation table
ft/lbs inch/lbs kg/m Nm
17 200 2,30 22
20 240 2,80 27
25 300 3,50 34

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-DC-Coalescer-EN_2.0 Page 2/2 Rev. 2.0
K-Type Coalescer Element

COALESCER ELEMENT
For the Separation of Water and Solids from Aviation Fuels
according to EI 1581 3rd Edition, Group II, Class A, B & C and MIL-F-8901E.
Filter water separators are fitted with coalescer and separator elements and used on air-
craft refuelling vehicles, hydrant dispensers and other mobile fuelling equipment. They
are also used in fixed fuelling installations and tank farms. FAUDI Aviation coalescers are
commonly used in other branches of industry such as refineries, petrochemical plants
and marine applications where high efficiency filtration and separation is required.

Technical Details
Tested and approved to EI 1581 3rd edition, Group II, Class A, B & C and MIL-F-8901E.
Nominal Filtration: 1μm
Change-out Differential Pressure: 1.1 bar (15 psi)
Test- /Berst Pressure: 5.2 bar (75 psi)
Recommended Service Time (max.): 24 months1
Recommended Storage Time (max.): 24 months1&2
Operating Temperature: min. -30°C / max. 80°C
Flow Direction: In to Out
Outside Diameter: 152 mm (6”)
1
Manufacturer recommendation
2
Original packaging, 20°C and max. 50% humidity
after date of shipment out of stock of FAUDI Aviation GmbH

Standard Design
■ Inner tube in epoxy coated steel
■ Seals in NBR (Buna-N)
■ End caps made out of Polyamid/reinforced glass fibre
■ Labeling of end caps acc. to EI specification
(date of manufacturing, ID-Number, etc.)

Coalescer wrap

Pleated paper
filtration section

Support tube

Cotton outer sock

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-K-Coalescer-EN_2.0 Page 1/2 Rev. 2.0
 K-Type Coalescer Element
COALESCER ELEMENT
Sample of Marking

Article code:
K.1-842
Model

Endcap Design Nominal Length in mm

25 (1“)
1/2“ - 13 UNC
Ø50 (2“) Ø65 (29/16“) Ø89 (31/2“)
L

L
Ø105 (49/64“)

Ø152 (6“) Ø152 (6“) Ø152 (6“) Ø152 (6“)

Endcap Design 1 Endcap Design 3 Endcap Design 4 Endcap Design 7

Flat sealed (open end) Screw / thread based

Nominal Lenght L
(Incl. Seal) Endcap Design Nominal Lenght L Endcap Design
mm Zoll 1 3 4 mm Zoll 7
285 11 1/4 K.4-279
369 14 1/2 K.4-362 351 14 13/16 K.7-362
473 18 5/8
K.3-467
565 22 1/4
K.3-559 K.4-559 565 22 1/4 K.7-559
733 28 7/8
K.4-727 705 27 3/4
K.7-727
848 33 3/8
K.1-842 K.3-842 K.4-842 834 32 7/8
K.7-842
971 38 1/4
K.3-965 K.4-965 965 38 K.7-965
1099 43 1/4
K.4-1093 1114 43 7/8
K.7-1093
1428 56 1/4
K.4-1422 1418 56 7/8
K.7-1422

Torques

34 Nm (for center rod) 22 Nm

Flat Sealed
Endcap Design
1, 3 & 4

22 Nm 27 Nm
Torques Conversation Table
Screw / Thread based
ft/lbs inch/lbs kg/m Nm
Endcap Design
17 200 2,30 22
7
20 240 2,80 27
25 300 3,50 34

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-K-Coalescer-EN_2.0 Page 2/2 Rev. 2.0
MIL-Type Coalescer Element

COALESCER ELEMENT
For the Separation of Water and Solids from Aviation Fuels
according to EI 1581 5th Edition, Category M, Type S & S-LW.
Filter water separators are fitted with coalescer and separator elements and used on air-
craft refuelling vehicles, hydrant dispensers and other mobile fuelling equipment. They
are also used in fixed fuelling installations and tank farms. FAUDI Aviation coalescers are
commonly used in other branches of industry such as refineries, petrochemical plants
and marine applications where high efficiency filtration and separation is required.

Technical Details
Tested and approved to EI 1581 5th edition, Category M, Type S & S-LW
Nominal Filtration: 1μm
Change-out Differential Pressure: 1.1 bar (15 psi)
Test- /Berst Pressure: 5.2 bar (75 psi)
Recommended Service Time (max.): 24 months1
Recommended Storage Time (max.): 24 months1&2
Operating Temperature: min. -30°C / max. 80°C
Flow Direction: In to Out
Outside Diameter: 152 mm (6”)
1
Manufacturer recommendation
2
Original packaging, 20°C and max. 50% humidity
after date of shipment out of stock of FAUDI Aviation GmbH

Standard Design
■ Inner tube in epoxy coated steel
■ Seals in NBR (Buna-N)
■ End caps made out of Polyamid/reinforced glass fibre
■ Labeling of end caps acc. to EI specification
(date of manufacturing, ID-Number, etc.)

Coalescer wrap

Pleated paper
filtration section

Support tube

Cotton outer sock

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-MIL-Coalescer-EN_2.0 Page 1/2 Rev. 2.0
 MIL-Type Coalescer Element
COALESCER ELEMENT
Sample of Marking

Article code:
MIL.1-842
Model

Endcap Design Nominal Length in mm

Ø50 (2“)

25 (1“)
1/2“ - 13 UNC
Ø50 (2“) Ø65 (29/16“) Ø89 (31/2“)
L

L
Ø30
Ø105 (49/64“)

Ø152 (6“) Ø152 (6“) Ø152 (6“) Ø152 (6“) Ø152 (6“)

Endcap Design 1 Endcap Design 3 Endcap Design 4 Endcap Design 6 Endcap Design 7

OPEN END SCREW/THREAD BASE

nominal Length L Endcap nominal Length Endcap
(including sealing) Design L Design
mm inch 1 3 4 6 mm inch 7
285 11 1/4
MIL.4-279
369 14 1/2
MIL.4-362 MIL.4-362 351 14 13/16 MIL.7-362
473 18 5/8
MIL.3-467
565 22 1/4
MIL.3-559 MIL.4-559 MIL.4-559 565 22 1/4 MIL.7-559
733 28 7/8
MIL.4-727 705 27 3/4
MIL.7-727
848 33 3/8
MIL.1-842 MIL.3-842 MIL.4-842 MIL.4-842 834 32 7/8
MIL.7-842
971 38 1/4
MIL.3-965 MIL.4-965 965 38 MIL.7-965
1099 43 1/4
MIL.4-1093 1114 43 7/8
MIL.7-1093
1428 56 1/4 MIL.4-1422 1418 56 7/8 MIL.7-1422

Torques

34 Nm (for center rod) 22 Nm

Flat Sealed
Endcap Design
1, 3, 4 & 6

22 Nm 27 Nm
Torques Conversation Table
Screw / Thread based
Endcap Design ft/lbs inch/lbs kg/m Nm

7 17 200 2,30 22
20 240 2,80 27
25 300 3,50 34

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-MIL-Coalescer-EN_2.0 Page 2/2 Rev. 2.0
P-Type Coalescer Element

COALESCER ELEMENT
For the Separation of Water and Solids from Aviation Fuels
according to EI 1581 5th Edition, Category C, Type S & S-LW.
Filter water separators are fitted with coalescer and separator elements and used on air-
craft refuelling vehicles, hydrant dispensers and other mobile fuelling equipment. They
are also used in fixed fuelling installations and tank farms. FAUDI Aviation coalescers are
commonly used in other branches of industry such as refineries, petrochemical plants
and marine applications where high efficiency filtration and separation is required.
Technical Details
Tested and approved to EI 1581 Cat. C Type S & S-LW
Nominal Filtration: 1μm
Change-out Differential Pressure: 1.1 bar (15 psi)
Test- /Berst Pressure: 5.2 bar (75 psi)
Recommended Service Time (max.): 24 months1
Recommended Storage Time (max.): 24 months1&2
Operating Temperature: min. -30°C / max. 80°C
Flow Direction: In to Out
Outside Diameter: 152 mm (6”)
1
Manufacturer recommendation
2
Original packaging, 20°C and max. 50% humidity
after date of shipment out of stock of FAUDI Aviation GmbH

Standard Design
■ Inner tube in epoxy coated steel
■ Seals in NBR (Buna-N)
■ End caps made out of Polyamid/reinforced glass fibre
■ Labeling of end caps acc. to EI specification
(date of manufacturing, ID-Number, etc.)

Coalescer wrap

Pleated paper
filtration section

Support tube

Cotton outer sock

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-P-Coalescer-EN_2.0 Page 1/2 Rev. 2.0
 P-Type Coalescer Element
COALESCER ELEMENT
Sample of Marking

Article code:
P.1-842
Model

Endcap Design Nominal Length in mm

25 (1“)
1/2“ - 13 UNC
Ø50 (2“) Ø65 (29/16“) Ø89 (31/2“)
L

L
Ø105 (49/64“)

Ø152 (6“) Ø152 (6“) Ø152 (6“) Ø152 (6“)

Endcap Design 1 Endcap Design 3 Endcap Design 4 Endcap Design 7

Flat sealed (open end) Screw / thread based

Nominal Lenght L
(Incl. Seal) Endcap Design Nominal Lenght L Endcap Design
mm Zoll 1 3 4 mm Zoll 7
285 11 1/4 P.4-279
369 14 1/2 P.4-362 351 14 13/16 P.7-362
473 18 5/8
P.3-467
565 22 1/4
P.3-559 P.4-559 565 22 1/4 P.7-559
733 28 7/8
P.4-727 705 27 3/4
P.7-727
848 33 3/8
P.1-842 P.3-842 P.4-842 834 32 7/8
P.7-842
971 38 1/4
P.3-965 P.4-965 965 38 P.7-965
1099 43 1/4
P.4-1093 1114 43 7/8
P.7-1093
1428 56 1/4
P.4-1422 1418 56 7/8
P.7-1422

Torques

34 Nm (for center rod) 22 Nm

Flat Sealed
Endcap Design
1, 3 & 4

22 Nm 27 Nm
Screw / Thread based
Torques Conversation Table
Endcap Design
ft/lbs inch/lbs kg/m Nm
7
17 200 2,30 22
20 240 2,80 27
25 300 3,50 34

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-P-Coalescer-EN_2.0 Page 2/2 Rev. 2.0
Y-Type Coalescer Element

COALESCER ELEMENT
For the Separation of Water and Solids from Aviation Fuels according to EI 1581
5th Edition, Category M, Type S as well technical delivery specifications of TL 4330-
0001 (Edition 1, Part 3)

Filter/Water separators are fitted with coalescer and separator elements and used on air-
craft refuelling vehicles, hydrant dispensers and other mobile fuelling equipment. They
are also used in fixed fuelling installations and tank farms. FAUDI Aviation Coalescers
are commonly used in other branches of industry such as refineries, petrochemical
plants and marine applications where high efficiency filtration and separation is required.

Technical Details
Tested and approved to EI 1581 5th Edition Cat. M Type S and
TL 4330-0001 (Edition 1 Part 3 )
Nominal Filtration: 1μm
Change-out Differential Pressure: 1.1 bar (15 psi)
Test- /Berst Pressure: 5.2 bar (75 psi)
Recommended Service Time (max.): 24 months1
Recommended Storage Time (max.): 24 months1&2
Operating Temperature: min. -30°C / max. 80°C
Flow Direction: In to Out
Outside Diameter: 152 mm (6”)
1
Manufacturer recommendation
2
Original packaging, 20°C and max. 50% humidity
after date of shipment out of stock of FAUDI Aviation GmbH
Standard Design
■ Inner tube in epoxy coated steel
■ Seals in NBR (Buna-N)
■ End caps made out of carbon steel epoxy coated
■ Labeling of end caps acc. to EI specification
(date of manufacturing, ID-Number, etc.)

Coalescer wrap

Pleated paper
filtration section

Support tube

Cotton outer sock

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-Y-Coalescer-EN_2.0 Page 1/2 Rev. 2.0
 Y-Type Coalescer Element
COALESCER ELEMENT
Sample of Marking

Article code:
Y.1-842/5
Model acc. to 5th ed. of EI 1581

Endcap Design Nominal Length in mm

Ø50 (2“)

25 (1“)
1/2“ - 13 UNC
Ø50 (2“) Ø89 (31/2“)

L
L

L
Ø30
Ø105 (49/64“)

Ø152 (6“) Ø152 (6“) Ø152 (6“) Ø152 (6“)

Endcap Design 1 Endcap Design 4 Endcap Design 6 Endcap Design 7

Flat sealed Screw / thread based

Nominal Length L Endcap
(Including Seal) Endcap Design Nominal Length L Design
mm Zoll 1 4 6 mm Zoll 7
369 14 1/2
Y.6-362/5 351 14 13/16
Y.7-362/5
473 18 5/8
Y.4-467/5
565 22 1/4
Y.4-559/5 Y.6-559/5
848 33 3/8
Y.1-842/5 Y.4-842/5 Y.6-842/5 834 32 7/8 Y.7-842/5
1418 56 7/8
Y.7-1422/5

Torques

34 Nm (for center rod) 22 Nm

Flat Sealed
Endcap Design
1&4

22 Nm 27 Nm
Screw / Thread based
Endcap Design
7

Torques Conversation Table

ft/lbs inch/lbs kg/m Nm
17 200 2,30 22
20 240 2,80 27
25 300 3,50 34

FAUDI Aviation GmbH Phone: +49 6428 4465-275

Scharnhorststrasse 7 B Fax: +49 6428 4465-231
D-35260 Stadtallendorf E-Mail: [email protected]
Germany Web: www.faudi-aviation.com quality guarantees safety
DS-Y-Coalescer-EN_2.0 Page 2/2 Rev. 2.0