Pa Dal Mounting
Pa Dal Mounting
Pa Dal Mounting
A. Description
The Tilton Floor-mount pedal assembly has been designed to give the driver the
greatest control from a floor-mounted pedal. The pedal profile has been carefully
engineered to deliver the optimum pedal ratio. The welded steel and cast
aluminum pedals provide the strength and durability to handle the most severe
braking conditions. All pedal assemblies with dual brake master cylinders include
the balance bar assembly in the brake pedal.
The balance bar allows the crew to adjust the force distribution to the dual master
cylinders. This system can be used to compensate for fuel load changes and tire
wear during an event. The Remote Cable Adjuster (P/N 72-501 or P/N 72-401)
is also available as an option. This connects to the balance bar and allows the
driver or a crew member to make balance bar adjustments with a flick of the wrist.
Installation Notes
• Secure the pedal frame to both the floor and the firewall, if at all possible.
• The mounting location should suit the particular driver and also provide a stable platform.
• A cross member support under the pedal frame will greatly enhance the stability of the pedal assembly.
• Determine if the master cylinder reservoirs are to be remotely-mounted or attached directly to the master cylinder.
• If you have decided to remotely-mount the reservoirs, select the locations for the reservoirs before starting installation.
• This is a gravity fed system so the reservoirs must be located above the calipers.
• If the Remote Cable Adjuster is part of your kit, select a mounting location and trial fit it into the vehicle before installation.
• Attention must be paid to the routing and location of the hydraulic lines. Avoid any heat sources such as exhaust pipes.
• It is very important to allow adequate clearance for ease of balance bar adjustment.
• The balance bar mechanism must clear all obstructions when the balance bar is adjusted to the extreme right or left-of-center.
• Be sure that there is no binding during the full stroke of the master cylinders.
• Accurate clutch pedal setup is critically important. Improper clutch pedal installation and/or adjustment can result in expensive clutch damage
and DNFs at the track!
• If the master cylinders are mounted in such a way that they are exposed in an open wheel well, a sheet metal guard should be installed to protect
the hydraulic system from damage.
B. Installation
1. Trial fit the pedal assembly into the vehicle and note any adjustments that are needed. It is important to mount the
frame rigidly so it does not move when heavy pedal force is applied.
2. Refer to Diagram 3 and mark the mounting hole locations on the floor of the vehicle.
3. If your application allows for firewall or bulkhead mounting in addition to floor mounting, mark the hole locations for the
firewall mounting holes at this time.
4. When satisfied with the mounting locations, drill the mounting holes into the floor and 8"
the firewall if applicable. Install the pedal assembly into the vehicle using the
hardware provided in the kit.
5. Install the master cylinders onto the pedal frame and secure them using the serrated
Firewall or Bulkhead
Diagram 1
Brake Pedal Setup
C. Brake Pedal Setup
1. Thread the jam nuts all the way onto the master cylinder pushrods.
2. Thread the pushrods into the clevises on the balance bar assembly.
3. Adjust the pushrods evenly until the brake pedal is set-up according to Diagram 1. This is a good starting point that
may need adjustment to fit the driver. In general, the pedal, in the relaxed position, should lean towards the driver.
4. To perform the balance bar setup refer to the balance bar installation instructions.
5. The clevis-to-clevis center distance must be maintained at 2.50”.
E. Clutch Pedal Stop Setup (For use with Tilton hydraulic release bearings)
1. Raise the vehicle onto jack stands or a hydraulic lift.
2. With the engine off, put the transmission into 1st gear and have someone attempt to rotate one of the drive wheels.
3. Depress the clutch pedal slowly until the clutch disengages and the drive wheel can be rotated.
4. Note the clutch pedal position at this point. This is labeled “A” in Diagram 2.
5. Adjust the pedal stop bolt to allow an additional 1/4” of pedal travel past point “A” in Diagram 2. This is labeled as
point “B” in Diagram 2.
1/4"
"B" "A"
Diagram 2
Pedal Stop Setup
Diagram 3
Mounting Hole Locations
Note: Drill 11/32” clearance holes for mounting bolts
F. Maintenance
Periodic inspections of the brake and clutch pedal assemblies should be conducted routinely. Rebuild kits for master
cylinders are available from Tilton Engineering.
25 Easy Street • Box 1787 • Buellton, CA 93427 • USA • (805) 688-2353 Fax (805) 688-9407
98-1200