The document describes the DOS-100 PCB, which is installed on an elevator inspector and connected to the DOC-200 PCB controller via communication line. It monitors the overall elevator status and informs it. The DOS-100 PCB has an MPU, communication blocks, and relays to control external devices like a 7-segment display or lamps based on the elevator status received from the DOC-200 PCB. It also has switches and LED indicators for resetting, status checking, and ID settings for the communication.
The document describes the DOS-100 PCB, which is installed on an elevator inspector and connected to the DOC-200 PCB controller via communication line. It monitors the overall elevator status and informs it. The DOS-100 PCB has an MPU, communication blocks, and relays to control external devices like a 7-segment display or lamps based on the elevator status received from the DOC-200 PCB. It also has switches and LED indicators for resetting, status checking, and ID settings for the communication.
The document describes the DOS-100 PCB, which is installed on an elevator inspector and connected to the DOC-200 PCB controller via communication line. It monitors the overall elevator status and informs it. The DOS-100 PCB has an MPU, communication blocks, and relays to control external devices like a 7-segment display or lamps based on the elevator status received from the DOC-200 PCB. It also has switches and LED indicators for resetting, status checking, and ID settings for the communication.
The document describes the DOS-100 PCB, which is installed on an elevator inspector and connected to the DOC-200 PCB controller via communication line. It monitors the overall elevator status and informs it. The DOS-100 PCB has an MPU, communication blocks, and relays to control external devices like a 7-segment display or lamps based on the elevator status received from the DOC-200 PCB. It also has switches and LED indicators for resetting, status checking, and ID settings for the communication.
1. Introduction DOS-100 PCB installed on to the inspector and connected with controller DOC-200 PCB by
communication line, informs overall status of the elevator
1.1 DOS-100 PCB Outline Drawing(Size 218*280 mm)
1.2 DOS-100 PCB STRUCTURE DIAGRAM
DOS-100 PCB HAS BLOCK DIAGRAM as below.
DOS-100 PCB
MC connector KEEP REARY
G/A MPU & BUS Exterior in & communication CONTROL machinery DOC-200 PCB REARY
1.3 G/A communication
G/A communication contacts G/A in DOC-200 using SM connector and send data input
and decodes to MPU in DOS-100 PCB
1 1.4 MPU & BUS CONTROL MPU is ONE CHIP TYPE, 89C51, used in DOS-100 PCB. MPU decodes data from G/A , conveys to
BUS CONTROLLER and contol RELAY
1.5 KEEP RELAY & RELAY
Inspecting board can notifiy E/L status via SEVEN SEGMENTs which are linked with DOS-100's
RELAY and informed of basic floor data.
DOS-100 PCB's KEEP RELAY(Preserved type) keeps its normal status even at power failure,
therefore, recent status data of E/L is available to access by exterior machinery power
2. Signs DOS-100 PCB has 2 LEDs.
LED No Function Sign
LED1 CPU interrupt input No.1, OFF when processing interrupt input
LED2 displays communication status on and off when communicating
3. Switch DOS-100 PCB has 2 switches. Name Function Others
S1 CPU RESET S2 For setting ID of the G/A communication Refer to Table1, ID setting
Table 1) DIP SW table for ID setting
PIN No Function 1 ON : Terminal Resistor ON, OFF : Terminal Resistor OFF
2 ON : Slave(When it connected to CRT or DAS), OFF : Normal
3 ON : Announciator available, OFF : Announciator disable
4 Option
5 Option
6 ON : B or b, OFF : " "
7 PIN 7 OFF & PIN 8 OFF : 7-Segment CPI, PIN : OFF & PIN 8 ON : Lamp Type CPI
8 PIN7 ON & PIN 8 OFF : Binary Type CPI(KOREA JuGong CRT)
2 4. Connector explanation 4.1 PW connector(Power) : Pin No. 1=>VCC(+5V), Pin No. 4=>Gnd 4.2 SM connector(for communication) : MC connector of the DOC-200 PCB 4.3 7-SEG structure is as following
N1 A a
F B f b H J h j
E G1 G2 g1 g2 C e c
N2 D d 10th position 1th position
4.4 KA connector(22PIN) :Connected of external Device
Pin No RY No RY Type Data 7-Segment CPI Lamp CPI Binary CPI
1 RY1 Normal close D0 7-Segment(a) 1 Floor Lamp Binary1
2 RY2 Normal close D1 7-Segment(b) 2 Floor Lamp Binary2 3 RY3 Normal close D2 7-Segment(c) 3 Floor Lamp Binary3 4 RY4 Normal close D3 7-Segment(d) 4 Floor Lamp Binary4 5 RY5 Normal close D4 7-Segment(e) 5 Floor Lamp Binary5 6 RY6 Normal close D5 7-Segment(f) 6 Floor Lamp Binary6 7 RY7 Normal close D6 7-Segment(g1) 7 Floor Lamp 8 RY8 Normal close D7 7-Segment(g2) 8 Floor Lamp 9 RY9 Normal close D0 7-Segment(A) 9 Floor Lamp Display Up SDS failure 10 RY10 Normal close D1 7-Segment(B) 10 Floor Lamp Display Down SDS failure 11 RY11 Normal close D2 7-Segment(C) 11 Floor Lamp Display stop between floor 12 RY12 Normal close D3 7-Segment(D) 12 Floor Lamp Display unable Door open 13 RY13 Normal close D4 7-Segment(E) 13 Floor Lamp Display unable Door close 14 RY14 Normal close D5 7-Segment(F) 14 Floor Lamp Display unable Runing 15 RY15 Normal close D6 7-Segment(G1) 15 Floor Lamp Display unable Leveling 16 RY16 Normal close D7 7-Segment(G2) 16 Floor Lamp Display Brake failure 17 RY17 Normal close D0 7-Segment(h,j) 17 Floor Lamp 18 RY18 Normal close D1 7-Segment(H,J) 18 Floor Lamp Disaply failure 19 RY19 Normal close D2 7-Segment(N1,N 19 Floor Lamp 20 RY20 Normal close D3 20 Floor Lamp 21 RY21 Normal close D4 21 Floor Lamp RY1~RY21 RY1~RY21 RY1~RY21 Common line 22 Common line Common line
3 4.5 KB connector(22PIN) :Connected of external Device Pin No RY No RY Type Data 7-Segment CPI Lamp CPI Binary CPI
1 RY22 Normal close D0 22 Floor Lamp
2 RY23 Normal close D1 23 Floor Lamp 3 RY24 Normal close D2 24 Floor Lamp 4 RY25 Normal open D3 Lift No. Lamp Lift No. Lamp Lift No. Lamp 5 RY26 Normal open D4 Up Lamp Up Lamp Up Lamp 6 RY27 Normal open D5 Down Lamp Down Lamp Down Lamp 7 RY28 Normal open D6 Safety Lamp Safety Lamp Safety Lamp 8 RY29 Normal open D7 Out of SVC Lamp Out of SVC Lamp Out of SVC Lamp 9 RY30 Normal open D0 Fire Lamp Fire Lamp Fire Lamp 10 RY31 Normal open D1 Normal power Lamp Normal power Lamp Normal power Lamp 11 RY32 Normal open D2 Generator Lamp Generator Lamp Generator Lamp 12 RY33 Normal open D3 Open Lamp Open Lamp Open Lamp 13 RY34 Normal open D4 Close Lamp Close Lamp Close Lamp 14 RY35 Normal open D5 Maint Lamp Maint Lamp Maint Lamp 15 RY36 Normal open D6 Over load Lamp Over load Lamp Over load Lamp 16 RY37 Normal open D7 Auto Lamp Auto Lamp Auto Lamp 17 RY38 Normal open D0 ATT Lamp ATT Lamp ATT Lamp 18 RY39 Normal open D1 Independent Lamp Independent Lamp Independent Lamp 19 RY40 Normal open D2 Parking Lamp Parking Lamp Parking Lamp 20 RY41 Normal open D3 Emergency Lamp Emergency Lamp Emergency Lamp 21 D4
