ELECTRICAL & POWER CONTROL

SECTION
BODY CONTROL SYSTEM
BCS B

E
CONTENTS
BASIC INSPECTION .................................... 3 BCM ...........................................................................16 F
BCM : CONSULT-III Function (BCM - BCM) ...........17
INSPECTION AND ADJUSTMENT ..................... 3
DOOR LOCK ..............................................................17
ADDITIONAL SERVICE WHEN REPLACING G
DOOR LOCK : CONSULT-III Function (BCM -
CONTROL UNIT .......................................................... 3 DOOR LOCK) ..........................................................17
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description .................................. 3 REAR WINDOW DEFOGGER ...................................18 H
ADDITIONAL SERVICE WHEN REPLACING REAR WINDOW DEFOGGER : CONSULT-III
CONTROL UNIT : Special Repair Requirement ...... 3 Function (BCM - REAR DEFOGGER) .....................18

CONFIGURATION ....................................................... 3 BUZZER .....................................................................18 I

CONFIGURATION : Description ............................... 3 BUZZER : CONSULT-III Function (BCM - BUZZ-
CONFIGURATION : Special Repair Requirement...... 4 ER) ..........................................................................18
J
FUNCTION DIAGNOSIS ............................... 7 INT LAMP ...................................................................19
INT LAMP : CONSULT-III Function (BCM - INT
BODY CONTROL SYSTEM ................................ 7 LAMP) ......................................................................19
System Description ................................................... 7 K
MULTIREMOTE ENT .................................................19
Component Parts Location ........................................ 8
MULTIREMOTE ENT : CONSULT-III Function
COMBINATION SWITCH READING SYSTEM (BCM - MULTIREMOTE ENT) .................................19 L
..... 9 HEADLAMP ...............................................................20
System Diagram ........................................................ 9 HEADLAMP : CONSULT-III Function (BCM -
System Description ................................................... 9 HEAD LAMP) ...........................................................20 BCS
Component Parts Location ...................................... 12
WIPER ........................................................................21
SIGNAL BUFFER SYSTEM ...............................13 WIPER : CONSULT-III Function (BCM - WIPER)....21
System Diagram ...................................................... 13 N
System Description ................................................. 13 FLASHER ...................................................................22
FLASHER : CONSULT-III Function (BCM -
POWER CONSUMPTION CONTROL SYS- FLASHER) ...............................................................22 O
TEM ....................................................................14
System Diagram ...................................................... 14 AIR CONDITIONER ...................................................23
System Description ................................................. 14 AIR CONDITIONER : CONSULT-III Function
Component Parts Location ...................................... 15 (BCM - AUTO AIR CONDITIONER) ........................23 P

DIAGNOSIS SYSTEM (BCM) ............................16 INTELLIGENT KEY ....................................................23

INTELLIGENT KEY : CONSULT-III Function
COMMON ITEM ......................................................... 16 (BCM - INTELLIGENT KEY) ....................................23
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ..................................................... 16 COMB SW ..................................................................24

BCS-1
 COMB SW : CONSULT-III Function (BCM - Special Repair Requirement ................................... 32
COMB SW) ............................................................. 24
COMBINATION SWITCH OUTPUT CIRCUIT ... 33
IMMU ......................................................................... 24 Diagnosis Procedure ............................................... 33
IMMU : CONSULT-III Function (BCM - IMMU) ....... 24 Special Repair Requirement ................................... 33
BATTERY SAVER .................................................... 25 COMBINATION SWITCH .................................. 34
BATTERY SAVER : CONSULT-III Function (BCM Description .............................................................. 34
- BATTERY SAVER) .............................................. 25 Diagnosis Procedure ............................................... 34
THEFT ALM .............................................................. 26 ECU DIAGNOSIS ....................................... 35
THEFT ALM : CONSULT-III Function (BCM -
THEFT ALM) .......................................................... 26 BCM (BODY CONTROL MODULE) .................. 35
Reference Value ..................................................... 35
SIGNAL BUFFER ...................................................... 26
Terminal Layout ...................................................... 38
SIGNAL BUFFER : CONSULT-III Function (BCM
Physical Values ....................................................... 39
- SIGNAL BUFFER) ................................................ 26
Wiring Diagram ....................................................... 50
PTC HEATER ............................................................ 26 DTC Inspection Priority Chart ............................... 53
PTC HEATER : CONSULT-III Function (BCM - DTC Index .............................................................. 54
PTC HEATER) ........................................................ 26
SYMPTOM DIAGNOSIS ............................ 55
COMPONENT DIAGNOSIS ........................ 28
COMBINATION SWITCH SYSTEM SYMP-
U1000 CAN COMM CIRCUIT ............................ 28 TOMS ................................................................. 55
Description .............................................................. 28 Symptom Table ....................................................... 55
DTC Logic ............................................................... 28
Diagnosis Procedure .............................................. 28 PRECAUTION ............................................ 56

U1010 CONTROL UNIT (CAN) ......................... 29 PRECAUTIONS ................................................. 56

DTC Logic ............................................................... 29 Precaution for Supplemental Restraint System
Diagnosis Procedure .............................................. 29 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
Special Repair Requirement ................................... 29 SIONER" ................................................................. 56

POWER SUPPLY AND GROUND CIRCUIT ..... 30 ON-VEHICLE REPAIR ............................... 57

Diagnosis Procedure .............................................. 30
BCM (BODY CONTROL MODULE) .................. 57
COMBINATION SWITCH INPUT CIRCUIT ....... 31 Removal and Installation of BCM ............................ 57
Diagnosis Procedure .............................................. 31

BCS-2
 INSPECTION AND ADJUSTMENT
< BASIC INSPECTION >
BASIC INSPECTION A
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
B
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000001451449

When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before C
replacement.
Configuration has three functions as follows
• READ CONFIGURATION is the function to read (extract) vehicle configuration of current BCM. D
• WRITE CONFIGURATION - Manual selection is the function to select and write vehicle configuration on
BCM manually.
• WRITE CONFIGURATION - Config file is the function to write vehicle configuration with the data extracted
E
from current BCM.
CAUTION:
• When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
• Complete the procedure of WRITE CONFIGURATION in order. F
• If you set incorrect WRITE CONFIGURATION, incidents will occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re- G
quirement INFOID:0000000001451450

1. SAVING VEHICLE SPECIFICATION H

Perform “READ CONFIGURATION” with CONSULT-III to save or print current vehicle specification.
I
>> GO TO 2
2. REPLACE BCM
J
Replace BCM. Refer to BCS-57, "Removal and Installation of BCM".

>> GO TO 3 K
3. WRITING VEHICLE SPECIFICATION
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” with
CONSULT-III to write vehicle specification. Refer to BCS-4, "CONFIGURATION : Special Repair Require- L
ment".

>> GO TO 4 BCS
4. INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS) N

>> WORK END

CONFIGURATION O

CONFIGURATION : Description INFOID:0000000001451451

Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM. P
Configuration has three functions as follows
• READ CONFIGURATION is the function to read (extract) vehicle configuration of current BCM.
• WRITE CONFIGURATION - Manual selection is the function to select and write vehicle configuration on
BCM manually.
• WRITE CONFIGURATION - Config file is the function to write vehicle configuration with the data extracted
from current BCM.
CAUTION:

BCS-3
 INSPECTION AND ADJUSTMENT
< BASIC INSPECTION >
• When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
• Complete the procedure of WRITE CONFIGURATION in order.
• If you set incorrect WRITE CONFIGURATION, incidents will occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
CONFIGURATION : Special Repair Requirement INFOID:0000000001451452

1. WRITING VEHICLE SPECIFICATION

Perform “WRITE CONFIGURATION” with CONSULT-III.

When writing saved data>>GO TO 2

When writing manually>>GO TO 3
2. PERFORM “WRITE CONFIGURATION - CONFIG FILE”
Perform “WRITE CONFIGURATION - Config file” with CONSULT-III.

>> WORK END

3. PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
For “WRITE CONFIGURATION - Manual selection”, using the following flow chart, identify the correct model
and configuration list.
Confirm and/or change setting value for each item according to the configuration list.
Depending on CONSULT-III software version being used, some or all of the write configuration items shown in
the following configuration lists may be displayed. If an item does not display on the CONSULT-III “WRITE
CONFIGURATION - Manual selection” screen, then it is an auto setting item and it cannot be manually set or
changed.
• Gasoline engine models (RHD)

MANUAL SETTING ITEM

Items Setting value
HANDLE RHD
PTC HEATER WITHOUT
AUTO LIGHT WITH⇔WITHOUT
KEYLESS ENTRY WITH⇔WITHOUT
DTRL WITHOUT
THEFT ALARM WITH⇔WITHOUT
AUTO SETTING ITEM
RAIN SENSOR WITH or WITHOUT
H/L WSR SWTRG FR WSR SW
H/L_BULB H4 HALOGEN or DEFAULT
FR FOG LAMP WITH or WITHOUT
DONGLE WITH or WITHOUT
SUPER LOCK WITH
I-KEY WITH or WITHOUT
DOOR/L SPEED WITH
H/L BAT SAVER WITH
KEY WARNING MODE1
R LAMP LOGIC MODE2
• Gasoline engine models (LHD)

BCS-4
 INSPECTION AND ADJUSTMENT
< BASIC INSPECTION >

MANUAL SETTING ITEM A

Items Setting value
HANDLE LHD
B
PTC HEATER WITHOUT
AUTO LIGHT WITH⇔WITHOUT
KEYLESS ENTRY WITH⇔WITHOUT C
DTRL WITH⇔WITHOUT
THEFT ALARM WITHOUT
D
AUTO SETTING ITEM
RAIN SENSOR WITH or WITHOUT
H/L WSR SWTRG FR WSR SW E
H/L_BULB H4 HALOGEN or DEFAULT
FR FOG LAMP WITH or WITHOUT
DONGLE WITH or WITHOUT
F
SUPER LOCK WITHOUT
I-KEY WITH or WITHOUT
G
DOOR/L SPEED WITH
H/L BAT SAVER WITH
KEY WARNING MODE1 H
R LAMP LOGIC MODE2
• Diesel engine models (RHD) I

MANUAL SETTING ITEM

Items Setting value J
HANDLE RHD
PTC HEATER WITHOUT
K
AUTO LIGHT WITH⇔WITHOUT
KEYLESS ENTRY WITH⇔WITHOUT
DTRL WITHOUT L
THEFT ALARM WITH⇔WITHOUT
AUTO SETTING ITEM
RAIN SENSOR WITH or WITHOUT
BCS

H/L WSR SWTRG FR WSR SW

H/L_BULB H4 HALOGEN or DEFAULT
N
FR FOG LAMP WITH or WITHOUT
DONGLE WITH or WITHOUT
SUPER LOCK WITH O
I-KEY WITH or WITHOUT
DOOR/L SPEED WITH
P
H/L BAT SAVER WITH
KEY WARNING MODE1
R LAMP LOGIC MODE2
• Diesel engine models (LHD)

BCS-5
 INSPECTION AND ADJUSTMENT
< BASIC INSPECTION >

MANUAL SETTING ITEM

Items Setting value
HANDLE LHD
PTC HEATER 2 PTC
AUTO LIGHT WITH⇔WITHOUT
KEYLESS ENTRY WITH⇔WITHOUT
DTRL WITH⇔WITHOUT
THEFT ALARM WITHOUT
AUTO SETTING ITEM
RAIN SENSOR WITH or WITHOUT
H/L WSR SWTRG FR WSR SW
H/L_BULB H4 HALOGEN or DEFAULT
FR FOG LAMP WITH or WITHOUT
DONGLE WITH or WITHOUT
SUPER LOCK WITHOUT
I-KEY WITH or WITHOUT
DOOR/L SPEED WITH
H/L BAT SAVER WITH
KEY WARNING MODE1
R LAMP LOGIC MODE2

>> WORK END

BCS-6
 BODY CONTROL SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS A
BODY CONTROL SYSTEM
System Description INFOID:0000000001451453
B

OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to C
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power consump- D
tion control function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings. E
BCM control function list

System Refer to F
Combination switch reading system BCS-9, "System Diagram"
Signal buffer system BCS-13, "System Diagram"
G
Power consumption control system BCS-14, "System Diagram"
Auto light system EXL-12, "System Diagram"
Turn signal and hazard warning lamp system EXL-22, "System Diagram" H
Headlamp system EXL-8, "System Diagram"
Front fog lamp system EXL-19, "System Diagram"
I
Rear fog lamp system EXL-21, "System Diagram"
Daytime light system EXL-17, "System Diagram"
Interior room lamp control system INL-5, "System Diagram" J
INL-12, "BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAV-
Interior room lamp battery saver system
ER)"
Front wiper and washer system WW-4, "System Diagram" K
Rear wiper and washer system WW-9, "System Diagram"
Headlamp washer system WW-12, "System Diagram"
L
Warning chime system WCS-4, "WARNING CHIME SYSTEM : System Diagram"
• WITH I-KEY, WITHOUT SUPER LOCK: DLK-20, "DOOR LOCK AND UN-
LOCK SWITCH : System Diagram"
• WITH I-KEY & SUPER LOCK: DLK-244, "DOOR LOCK AND UNLOCK BCS
SWITCH : System Diagram"
Door lock system
• WITHOUT I-KEY & SUPER LOCK: DLK-473, "DOOR LOCK AND UN-
LOCK SWITCH : System Diagram"
• WITHOUT I-KEY, WITH SUPER LOCK: DLK-614, "DOOR LOCK AND UN-
N
LOCK SWITCH : System Diagram"
• WITH INTELLIGENT KEY SYSTEM: SEC-12, "System Diagram"
(NATS) Nissan anti-theft system O
• WITHOUT INTELLIGENT KEY SYSTEM: SEC-84, "System Diagram"
Rear window defogger system DEF-6, "System Diagram"
• WITHOUT I-KEY & SUPER LOCK: DLK-475, "REMOTE KEYLESS EN-
TRY : System Diagram" P
Remote keyless entry system
• WITHOUT I-KEY, WITH SUPER LOCK: DLK-614, "DOOR LOCK AND UN-
LOCK SWITCH : System Diagram"
• WITH I-KEY, WITHOUT SUPER LOCK: DLK-23, "INTELLIGENT KEY :
System Diagram"
Intelligent Key system
• WITH I-KEY & SUPER LOCK: DLK-244, "DOOR LOCK AND UNLOCK
SWITCH : System Diagram"

BCS-7
 BODY CONTROL SYSTEM
< FUNCTION DIAGNOSIS >
System Refer to
Power window system PWC-6, "System Diagram"
PTC heater control system HAC-142, "PTC HEATER (300 WATT) : PTC Heater System Description"

Component Parts Location INFOID:0000000001451454

• BCM (1) M18, M19, M20 (view with glove box removed)

WKIA5663E

BCS-8
 COMBINATION SWITCH READING SYSTEM
< FUNCTION DIAGNOSIS >
COMBINATION SWITCH READING SYSTEM
A
System Diagram INFOID:0000000001451455

JPMIA0120GB

G
System Description INFOID:0000000001451456

OUTLINE H
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
• BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a I
maximum of 20 switch status.
COMBINATION SWITCH MATRIX
J
Combination switch circuit

BCS

O
JPMIA0121GB

Combination switch INPUT-OUTPUT system list P

System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 RR WASHER — HEADLAMP 2 HI BEAM

BCS-9
 COMBINATION SWITCH READING SYSTEM
< FUNCTION DIAGNOSIS >
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 4 RR WIPER INT INT VOLUME 3 AUTO LIGHT — TAIL LAMP
INPUT 5 INT VOLUME 2 RR WIPER RR FOG FR FOG —
NOTE:
Headlamp has a dual system switch.

COMBINATION SWITCH READING FUNCTION

Description
• BCM reads the status of the combination switch at 10 ms interval normally.

JPMIA0067GB

NOTE:
BCM reads the status of the combination switch at 20 ms interval when BCM is controlled at low power con-
sumption control mode.
• BCM operates as follows and judges the status of the combination switch.
- INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 5 → 4 → 3 → 2 → 1.
- The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of
the transistor on OUTPUT side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.

JPMIA0068GB

Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.
Example 1: When a switch (TURN RH switch) is turned ON

BCS-10
 COMBINATION SWITCH READING SYSTEM
< FUNCTION DIAGNOSIS >
• The circuit between INPUT 1 and OUTPUT 5 is formed when the TURN RH switch is turned ON.
A

JPMIA0122GB F
• BCM detects the combination switch status signal “1E” when the signal of OUTPUT 5 is input to INPUT 1.
• BCM judges that the TURN RH switch is ON when the signal “1E” is detected.
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON G
• The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the
TURN RH switch and FR WIPER LOW switch are turned ON.
H

JPMIA0123GB
BCS
• BCM detects the combination switch status signal “1CE” when the signals of OUTPUT 3 and OUTPUT 5 are
input to INPUT 1.
• BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal “1CE” is
detected. N
WIPER INTERMITTENT DIAL POSITION SETTING (FRONT WIPER INTERMITTENT OPERATION)
BCM judges the wiper intermittent dial 1 - 7 by the status of INT VOLUME 1, 2 and 3 switches.
O

BCS-11
 COMBINATION SWITCH READING SYSTEM
< FUNCTION DIAGNOSIS >

Intermittent INT VOLUME switch ON/OFF status

Wiper intermittent
operation delay
dial position INT VOLUME 1 switch INT VOLUME 2 switch INT VOLUME 3 switch
interval
1 ON ON ON
Short
2 ↑ ON ON OFF
3 ON OFF OFF
4 OFF OFF OFF
5 OFF OFF ON
6 ↓ OFF ON ON
Long
7 OFF ON OFF

Component Parts Location INFOID:0000000001451457

ALMIA0186ZZ

1. BCM M18, M19, M20 (view with 2. Combination switch (light and turn 3. Combination switch (wiper and
glove box removed) signal switch) M28 washer switch) M28

BCS-12
 SIGNAL BUFFER SYSTEM
< FUNCTION DIAGNOSIS >
SIGNAL BUFFER SYSTEM
A
System Diagram INFOID:0000000001451458

JPMIA0124GB F

System Description INFOID:0000000001451459

G
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
H
Signal transmission function list

Signal name Input Output Description

I
• Combination meter (CAN)
Inputs the door switch signal
• IPDM E/R (CAN)
Door switch signal Any door switch and transmits it via CAN com-
• Intelligent Key unit (CAN)
munication.
• NAVI control unit (CAN) J
Inputs the stop lamp switch sig-
TCM (CAN) nal and transmits the stop lamp
Stop lamp switch signal Stop lamp switch
ECM (CAN) switch signal via CAN commu- K
nication.
Transmits the received oil pres-
Oil pressure switch signal IPDM E/R (CAN) Combination meter (CAN) sure switch signal via CAN
communication.
L

BCS

BCS-13
 POWER CONSUMPTION CONTROL SYSTEM
< FUNCTION DIAGNOSIS >
POWER CONSUMPTION CONTROL SYSTEM
System Diagram INFOID:0000000001451460

JPMIA0125GB

System Description INFOID:0000000001451461

OUTLINE
• BCM incorporates a power consumption control function that reduces the power consumption according to
the vehicle status.
• BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit [IPDM E/R, combination meter and Intelligent Key unit (with Intelligent Key)] that oper-
ates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)
- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
• The reading interval of the each switches changes from 10 ms interval to 20 ms interval.
Sleep mode activation
• BCM receives the sleep-ready signal (ready) from IPDM E/R, combination meter and Intelligent Key unit
(with Intelligent Key) via CAN communication.
• BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful-
filled.
• Each unit stops the transmission of CAN communication with the sleep wake up signal. BCM is in CAN com-
munication sleep mode.
• BCM is in the low power consumption mode and perform the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.

BCS-14
 POWER CONSUMPTION CONTROL SYSTEM
< FUNCTION DIAGNOSIS >
Sleep condition
CAN sleep condition BCM sleep condition A
• Receiving the sleep-ready signal (ready) from all units
• Ignition switch: OFF
• Vehicle security system alarm: No operation
B
• Warning lamp: No operation
• Warning chime: No operation
• Stop lamp switch: OFF The controls only BCM are completed.
• Key switch status: No change for 2 seconds (Interior room lamp battery saver: Time out etc.) C
• Hazard warning lamp: No operation
• Exterior lamp: OFF
• Door lock status: No change for 2 seconds
• CONSULT-III communication status: No communication D
• Door switch status: No change for 2 seconds

Wake-up operation
• BCM transmits sleep wake up signal (wake up) to each unit when any condition listed below is established, F
and then goes into normal mode from low power consumption mode.
• Each unit starts transmissions with CAN communication by receiving sleep wake up signals. Each unit trans-
mits wake up signals to BCM with CAN communication to convey the start of CAN communication. G
Wake-up condition
BCM wake-up condition
• Ignition switch: OFF → ACC or ON H
• Stop lamp switch: ON (Depress brake pedal)
• Any door switch: OFF → ON
• Lighting switch: OFF → 1ST or PASS
I
• Hazard switch: OFF → ON
• Back door opener switch OFF → ON
• Remote keyless entry receiver: Receiving (with remote keyless entry)
• Intelligent Key unit: Receiving (with Intelligent Key) J
Component Parts Location INFOID:0000000001451462

BCS

ALMIA0187ZZ

P
1. IPDM E/R E46 2. BCM M18, M19, M20 (view with 3. Intelligent Key unit M52 (with Intelli-
glove box removed) gent Key) (view with glove box re-
moved)
4. Combination meter M24

BCS-15
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001451463

APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description

WORK SUPPORT Changes the setting for each system function.
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to BCS-54, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
• Enables to read and save the vehicle specification.
CONFIGURATION
• Enables to write the vehicle specification when replacing BCM.

SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
BCM BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×

Remote keyless entry system1 MULTI REMOTE ENT × × ×

Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×

Intelligent Key system2 INTELLIGENT KEY ×

Combination switch COMB SW ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk open (sedan)/Back door open
DOOR LOCK × ×
(hatch back)
Vehicle security system THEFT ALM × × ×
Signal buffer system SIGNAL BUFFER × ×
PTC heater system PTC HEATER × ×
1: With remote keyless entry system
2: With Intelligent Key
BCM

BCS-16
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
BCM : CONSULT-III Function (BCM - BCM) INFOID:0000000001451464

A
WORK SUPPORT

Item Description B
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.

DOOR LOCK C
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) INFOID:0000000001451465

D
WORK SUPPORT

Work Item Description

E
Anti hijack function mode can be changed in this mode.
SECURITY DOOR LOCK SET • ON: Anti hijack mode is active.
• OFF: Anti hijack mode is inactive.
Auto door lock time can be changed in this mode. F
• MODE 1: 1 minute
• MODE 2: 2 minutes
AUTO LOCK SET
• MODE 3: 3 minutes
G
• MODE 4: 4 minutes
• MODE 5: 5 minutes

DATA MONITOR H

Monitor Item
Description
[Unit}
I
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position.

PUSH SW1 [ON/OFF] Indicates condition of ignition knob switch.

J
KEY SW2 [ON/OFF] Indicates condition of key switch.
CDL LOCK SW [ON/OFF] Indicates condition of door lock and unlock switch.
CDL UNLOCK SW [ON/OFF] Indicates condition of door lock and unlock switch. K
DOOR SW-DR [ON/OFF] Indicates condition of front door switch (driver side).
DOOR SW-AS [ON/OFF] Indicates condition of front door switch (passenger side).
DOOR SW-RR [ON/OFF] Indicates condition of rear door switch RH.
L
DOOR SW-RL [ON/OFF] Indicates condition of rear door switch LH.
TRNK OPNR SW [ON/OFF] Indicates condition of back door switch.
BCS
BACK DOOR SW [ON/OFF] Indicates condition of back door switch.

KEYLESS LOCK2 [ON/OFF] Indicates condition of lock signal from key fob.
N
KEYLESS UNLOCK2 [ON/OFF] Indicates condition of unlock signal from key fob.

I-KEY LOCK1 [ON/OFF] Indicates condition of lock signal from Intelligent Key.

I-KEY UNLOCK1 [ON/OFF] Indicates condition of unlock signal from Intelligent Key. O
1: With Intelligent Key
2: With remote keyless entry system
P
ACTIVE TEST

Test item Description

This test is able to check door lock operation [ALL LOCK/ALL UNLOCK/DR UNLOCK/
DOOR LOCK
OTHER UNLOCK].

SUPER LOCK* This test is able to check super lock operation [LOCK (SET)/UNLOCK (RELEASE)].

BCS-17
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
Test item Description
This test is able to check door lock indicator (built in door lock and unlock switch on center
DOOR LOCK IND
console) operation [ON/OFF].
This test is able to check trunk/back door lock operation [LOCK (SET)/UNLOCK (RE-
TRUNK/BACK DOOR
LEASE)].
*
: With super lock
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)
INFOID:0000000001451466

DATA MONITOR

Monitor Item
Description
[Unit]
ENGINE STATUS [RUN/
Indicates engine running status.
STOP]
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position.
REAR DEF SW [ON/OFF] Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.

ACTIVE TEST

Test Item Description

REAR DEFOGGER Give a drive signal to the rear window defogger relay to activate it.

BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000001451467

DATA MONITOR

Monitor Item
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judged by ignition power supply input.

PUSH SW1 [ON/OFF] Ignition knob status.

KEY SW2 [ON/OFF] Key switch status.

DOOR SW -DR [ON/OFF] Front door switch (driver side) status judged by BCM.
DOOR SW -AS [ON/OFF] Front door switch (passenger side) status judged by BCM.
DOOR SW -RR [ON/OFF] Rear door switch RH status judged by BCM.
DOOR SW -RL [ON/OFF] Rear door switch LH status judged by BCM.
BACK DOOR SW [ON/OFF] Back door switch status judged by BCM.
CDL LOCK SW [ON/OFF] Door lock/unlock switch status.
CDL UNLOCK SW [ON/OFF] Door lock/unlock switch status.
Lighting switch status judged by the lighting switch signal read with combination switch reading func-
LIGHTING SW [ON/OFF]
tion.
TRNK OPNR SW [ON/OFF] Trunk switch status.

ACTIVE TEST

Test Item Description

LIGHT WARN ALM The light reminder warning operation can be checked by operating the relevant function (On/Off).
KEY REMINDER WARN The key reminder warning operation can be checked by operating the relevant function (On/Off).

BCS-18
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
Test Item Description
A
BACK DR OPEN WARN The back door open warning operation can be checked by operating the relevant function (On/Off).
DOOR WARNING IND The door open warning operation can be checked by operating the relevant function (On/Off).

INT LAMP B

INT LAMP : CONSULT-III Function (BCM - INT LAMP) INFOID:0000000001451468

C
DATA MONITOR

Monitor item
Description D
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judges from IGN signal (ignition power supply)

PUSH SW1 [ON/OFF] Push switch status received from Intelligent Key unit by CAN communication E
KEY SW2 [ON/OFF] The switch status input from key switch
DOOR SW-DR [ON/OFF] The switch status input from front door switch (driver side)
F
DOOR SW-AS [ON/OFF] The switch status input from front door switch (passenger side)
DOOR SW-RR [ON/OFF] The switch status input from rear door switch RH
DOOR SW- RL [ON/OFF] The switch status input from rear door switch LH G
BACK DOOR SW [ON/OFF] The switch status input from back door switch
CDL LOCK SW [ON/OFF] Lock switch status input from door lock and unlock switch
H
CDL UNLOCK SW [ON/OFF] Unlock switch status input from door lock and unlock switch
Lock signal status received from remote keyless entry receiver (integrated in the
KEYLESS LOCK2 [ON/OFF] BCM)
I
2 Unlock signal status received from remote keyless entry receiver (integrated in the
KEYLESS UNLOCK [ON/OFF] BCM)

I-KEY LOCK1 [ON/OFF] Lock signal status received from Intelligent Key unit by CAN communication J
1 Unlock signal status received from Intelligent Key unit by CAN communication
I-KEY UNLOCK [ON/OFF]

I-KEY ALL UNL1 [ON/OFF] Unlock signal status received from Intelligent Key unit by CAN communication
K
1: With Intelligent Key
2: With remote keyless entry

ACTIVE TEST L

Test item Operation Description

Outputs the interior room lamp control signal to turn the interior room lamps ON. BCS
ON [Map lamp, personal lamp, room lamp, luggage room lamp (when applicable lamps
INT LAMP switch is in DOOR position.)]
OFF Stops the interior room lamp control signal to turn the interior room lamps. N
MULTIREMOTE ENT
MULTIREMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT) O
INFOID:0000000001451469

WORK SUPPORT P

BCS-19
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >

Work Item Description

Answer back function (hazard) mode can be changed in this mode.
HAZARD LAMP SET For the detail of the setting, refer to DLK-617, "REMOTE KEYLESS ENTRY : System Descrip-
tion".
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 2 minutes
AUTO LOCK SET
• MODE 3: 3 minutes
• MODE 4: 4 minutes
• MODE 5: 5 minutes

DATA MONITOR

Monitor Item
Condition
[Unit}
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position.
KEY SW [ON/OFF] Indicates condition of key switch.
KEYLESS LOCK [ON/OFF] Indicates condition of lock signal from keyfob.
KEYLESS UNLOCK [ON/OFF] Indicates condition of unlock signal from keyfob.
DOOR SW-DR [ON/OFF] Indicates condition of front door switch (driver side).
DOOR SW-AS [ON/OFF] Indicates condition of front door switch (passenger side).
DOOR SW-RR [ON/OFF] Indicates condition of rear door switch RH.
DOOR SW-RL [ON/OFF] Indicates condition of rear door switch LH.
BACK DOOR SW [ON/OFF] Indicates condition of back door switch.
CDL LOCK SW [ON/OFF] Indicates condition of door lock and unlock switch.
CDL UNLOCK SW [ON/OFF] Indicates condition of door lock and unlock switch.
RKE LOCK AND UNLOCK This item is indicated, but not monitored.

ACTIVE TEST

Test Item Description

This test is able to check warning chime in combination meter operation. [ALL LOCK/ALL UN-
DOOR LOCK
LOCK/DR UNLOCK/OTHER UNLOCK]
INT LAMP This test is able to check interior lamp operation [ON/OFF].
FLASHER This test is able to check flasher operation [LH/RH/OFF].

HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000001451470

WORK SUPPORT

Work item Setting Description

ON*
BATTERY SAVER SET Battery saver mode can be changed.
OFF
*: Initial setting

DATA MONITOR

Monitor item
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judged from IGN signal (ignition power supply)

BCS-20
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
Monitor item
Description
[Unit] A
HI BEAM SW [ON/OFF]
H/L SW POS [ON/OFF]
B
LIGHT SW 1ST [ON/OFF]
PASSING SW [ON/OFF] Each switch status that BCM judges from the combination switch reading function
AUTO LIGHT SW [ON/OFF] C
FR FOG SW [ON/OFF]
RR FOG SW [ON/OFF]
D
DOOR SW-DR [ON/OFF] The switch status input from front door switch (driver side)
ENGINE STATUS The engine status received from ECM with CAN communication
• The sensor status received from light & rain sensor with serial link E
LIT-SEN FAIL [OK/NOTOK]
• The serial link condition that BCM judges
AUT LIGHT SYS [ON/OFF] Auto light system status that BCM judges from the vehicle condition

ACTIVE TEST F

Test item Operation Description

G
Transmits the position light request signal to IPDM E/R with CAN com-
ON
TAIL LAMP munication to turn the tail lamp ON.
OFF Stops the tail lamp request signal transmission.
H
Transmits the high beam request signal with CAN communication to turn
HI
the headlamp (HI).
HEAD LAMP Transmits the low beam request signal with CAN communication to turn
LO I
the headlamp (LO).
OFF Stops the high & low beam request signal transmission.
Transmits the front fog lights request signal to IPDM E/R with CAN com-
ON J
FR FOG LAMP munication to turn the front fog lamp ON.
OFF Stops the front fog lights request signal transmission.
• Outputs the voltage to turn the rear fog lamp ON. K
ON • Transmits the rear fog lamp status signal to the combination meter with
RR FOG LAMP CAN communication to turn the rear fog lamp indicator lamp ON.
• Stops the voltage to turn the rear fog lamp OFF.
OFF
• Stops the rear fog lamp status signal transmission.
L

Transmits the day time running light request signal to IPDM E/R with
ON
DAYTIME RUNNING LIGHT CAN communication to turn the each lamps ON.
BCS
OFF Stops the day time running light request signal transmission.

WIPER
N
WIPER : CONSULT-III Function (BCM - WIPER) INFOID:0000000001451471

WORK SUPPORT O

Setting
Work Item Description
Item
P
With vehicle speed
ON1 (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
WIPER SPEED
SETTING Without vehicle speed
OFF
(Front wiper intermittent time linked with the wiper intermittent dial position)

RR WIP RVRS ON2

Change ON/OFF mode setting or rear wiper operation when gear is shifted to reverse
SET OFF

BCS-21
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
1: Factory setting
2: If equipped

DATA MONITOR

Monitor Item
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch ON status judged from ignition power supply.
FR WIPER HI [ON/OFF]
FR WIPER LOW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER INT [ON/OFF]
FR WASHER SW [ON/OFF]
INT VOLUME [1 - 7] Each switch status that BCM judges from the combination switch reading function.
Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
FR WIPER STOP [ON/OFF]
tion.
The value of the vehicle speed signal received from combination meter with CAN com-
VEHICLE SPEED [km/h]
munication.
H/L SW POS [ON/OFF]
RR WIPER ON [ON/OFF]
RR WIPER INT [ON/OFF] Each switch status that BCM judges from the combination switch reading function.
RR WASHER SW [ON/OFF]
RR WIPER STOP [ON/OFF] Rear wiper motor (stop position) status input from the rear wiper motor.
REVERSE SW CAN [ON/OFF] Transmission reverse position moitored via CAN.

ACTIVE TEST

Test Item Operation Description

HEADLAMP WASH- Transmits the headlamp washer request signal to IPDM E/R with CAN communication to
ON
ER operate the headlamp washer operation.
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
HI
erate the front wiper HI operation.
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
LO
FR WIPER operate the front wiper LO operation.
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
INT
operate the front wiper INT operation.
OFF Stops transmitting the front wiper request signal to stop the front wiper operation.
ON Outputs the voltage to operate the rear wiper motor.
RR WIPER
OFF Stops the voltage to stop.

FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER) INFOID:0000000001451472

WORK SUPPORT

Work Item Description

Operation MODE1 MODE2 MODE3

MODE4
HAZARD LAMP SET
Keyfob operation Lock Unlock Lock Unlock Lock Unlock Lock Unlock
Hazard lamp flash - - - Twice Once - Once Twice

DATA MONITOR

BCS-22
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >

Monitor Item A
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF] The switch status input from the hazard switch B
TURN SIGNAL R [ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
C
TURN/L MNTR [ON/OFF] Displays status (one bulb out: ON/other: OFF) as judged from bulb signal

ACTIVE TEST
D
Test Item Operation Description
RH Outputs the voltage to turn the right side turn signal lamps ON.
E
FLASHER LH Outputs the voltage to turn the left side turn signal lamps ON.
OFF Stops the voltage to turn the turn signal lamps OFF.

AIR CONDITIONER F

AIR CONDITIONER : CONSULT-III Function (BCM - AUTO AIR CONDITIONER)

INFOID:0000000001451473
G
ACTIVE TEST
H
Test Item Operation Description
ON Outputs the signal to turn the A/C indicator ON.
A?C INDICATOR
OFF Stops the signal to turn the A/C indicator OFF. I
DATA MONITOR

Monitor Item
J
Contents
[Unit]
Display [ignition switch position (On)/(Off), ACC position (Off)] status as judged form ignition
IGNSW [ON/OFF]
switch signal. K
FAN ON SIG [ON/OFF] Display [FAN (On)/FAN (Off)] status as judged form blower fan motor switch signal.
AIR COND SW [ON/OFF] Display [COMP (On)/COMP (Off)] status as judged form air conditioner switch signal.
L
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) INFOID:0000000001451474
BCS

DATA MONITOR
N
Monitor Item
Condition
[Unit]
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position.
O
PUSH SW [ON/OFF] Indicates condition of ignition knob switch.
I-KEY LOCK [ON/OFF] Indicates condition of lock signal from Intelligent Key.
I-KEY UNLOCK [ON/OFF] Indicates [condition of unlock signal from Intelligent Key. P
I-KEY ALL UNL [ON/OFF] Indicates condition of all unlock signal from Intelligent Key.
I-KEY TRUNK OP [ON/OFF] Indicates condition of trunk open signal from Intelligent Key.
DOOR SW-DR [ON/OFF] Indicates condition of front door switch (driver side).
DOOR SW-AS [ON/OFF] Indicates condition of front door switch (passenger side).
DOOR SW-RR [ON/OFF] Indicates condition of rear door switch RH.

BCS-23
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
Monitor Item
Condition
[Unit]
DOOR SW-RL [ON/OFF] Indicates condition of front door switch LH.
BACK DOOR SW [ON/OFF] Indicates condition of back door switch.

COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW) INFOID:0000000001451475

DATA MONITOR

Monitor Item
Description
[Unit]
TURN SIGNAL R Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function.
TURN SIGNAL L Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function.
HI BEAM SW Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function.
H/L SW POS Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
LIGHT SW 1ST Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
PASSING SW Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function.
AUTO LIGHT SW Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
FR FOG SW Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function.
RR FOG SW Displays the status of the RR FOG switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function.
FR WIPER HI Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
FR WIPER LOW Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
FR WIPER INT Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
FR WASHER SW Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
INT VOLUME Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
[1 - 7] function.
RR WIPER ON Displays the status of the RR WIPER switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
RR WIPER INT Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.
RR WASHER SW Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function.

IMMU
IMMU : CONSULT-III Function (BCM - IMMU) INFOID:0000000001451476

DATA MONITOR

BCS-24
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >

Monitor Item Description A

IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position.

KEY SW1 [ON/OFF] Indicates condition of key switch.

B
PUSH SW2 [ON/OFF] Indicates condition of ignition knob switch.
1: With remote keyless entry.
2: With Intelligent Key. C
ACTIVE TEST

Test Item Description D

THEFT IND This test is able to check security indicator operation [ON/OFF].

BATTERY SAVER E

BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) INFOID:0000000001451477

F
WORK SUPPORT

Work Item Setting Item Setting

G
MODE 1* 15 min. Sets the interior room lamp battery saver timer operating
ROOM LAMP TIMER SET
MODE 2 30 min. time.

*: Initial setting H
DATA MONITOR

Monitor Item
I
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judges from IGN signal (ignition power supply)
J
KEY SW1 [ON/OFF] The switch status input from key switch

PUSH SW2 [ON/OFF] Push switch status received from Intelligent Key unit by CAN communication
DOOR SW-DR [ON/OFF] The switch status input from front door switch (driver side) K
DOOR SW-AS [ON/OFF] The switch status input from front door switch (passenger side)
DOOR SW-RR [ON/OFF] The switch status input from rear door switch RH
L
DOOR SW- RL [ON/OFF] The switch status input from rear door switch LH
BACK DOOR SW [ON/OFF] The switch status input from back door switch
CDL LOCK SW [ON/OFF] Lock switch status input from door lock and unlock switch BCS
CDL UNLOCK SW [ON/OFF] Unlock switch status input from door lock and unlock switch
2 Lock signal status received from Intelligent Key unit by CAN communication
I-KEY LOCK [ON/OFF]
N
I-KEY UNLOCK2 [ON/OFF] Unlock signal status received from Intelligent Key unit by CAN communication
Lock signal status received from remote keyless entry receiver (integrated in the
KEYLESS LOCK1 [ON/OFF] BCM) O
Unlock signal status received from remote keyless entry receiver (integrated in the
KEYLESS UNLOCK1 [ON/OFF] BCM)
1: With remote keyless entry P
2: With Intelligent Key

ACTIVE TEST

Test item Operation Description

OFF Cuts the interior room lamp power supply to turn interior room lamps OFF.
BATTERY SAVER
ON Outputs the interior room lamp power supply to turn interior room lamps ON.*

BCS-25
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
*: Each lamp switch is in ON position.
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT ALM) INFOID:0000000001451479

WORK SUPPORT

Work Item Description

Vehicle security function mode can be changed in this mode.
SECURITY ALARM SET • ON: Vehicle security function is ON.
• OFF: Vehicle security function is OFF.

SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER) INFOID:0000000001451480

DATA MONITOR

Monitor Item
Description
[Unit]
OIL PRESS SW [ON/OFF] Displays the status of oil pressure switch received from IPDM E/R via CAN communication.

ACTIVE TEST

Test Item Operation Description

OFF OFF
OIL PRESSURE SW BCM transmits the oil pressure switch signal to the combination meter via CAN communica-
ON
tion, which illuminates the oil pressure warning lamp in the combination meter.

PTC HEATER
PTC HEATER : CONSULT-III Function (BCM - PTC HEATER) INFOID:0000000001451481

DATA MONITOR

Monitor Item
Description
[Unit]
ELEC PWR CUT
Indicate [OFF/FREEZ/INHBT] condition of the PTC heater states.
[OFF/FREEZ/INHBT]
FAN ON SIG
Displays [FAN (ON)/FAN (OFF)] status as judged from blower fan motor signal.
[On/Off]
ENGINE STATUS
Indicate [STOP/STALL/RUN/CRA] condition of the engine states.
[STOP/STAL/RUN/CRA]
ENG COOLNT T The engine coolant temperature (determined by the signal voltage of the engine coolant tem-
[°C] perature sensor) is displayed.
BATTERY VOLT
The power supply voltage of BCM is displayed.
[V]
ENGINE RPM
Indicates the engine speed computed from the signal of the crankshaft position sensor.
[rpm]
OUTSIDE TEMP
The outside air temperature (determined by the signal voltage of the OAT sensor) is displayed.
[°C]

ACTIVE TEST

BCS-26
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >

Test Item Operation Description A

OFF
PTC 1
PTC HEATER This test is able to check PTC heater operation.
PTC 2
B
PTC 3

BCS

BCS-27
 U1000 CAN COMM CIRCUIT
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description INFOID:0000000001451482

Refer to LAN-33, "CAN Communication Signal Chart".

DTC Logic INFOID:0000000001451483

DTC DETECTION LOGIC

CONSULT-III display
DTC DTC Detection Condition Possible cause
description
Any item (or items) of the following listed below is
malfunctioning in CAN communication system.
• Transmission
When BCM cannot communicate CAN com- • Receiving (ECM)
U1000 CAN COMM CIRCUIT munication signal continuously for 2 sec- • Receiving (METER/M&A)
onds or more. • Receiving (TCM)
• Receiving (MULTI AV)
• Receiving (IPDM E/R)
• Receiving (I-KEY)

Diagnosis Procedure INFOID:0000000001451484

1. PERFORM SELF DIAGNOSTIC

1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is “CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-22, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-55, "Intermittent Incident".

BCS-28
 U1010 CONTROL UNIT (CAN)
< COMPONENT DIAGNOSIS >
U1010 CONTROL UNIT (CAN)
A
DTC Logic INFOID:0000000001451485

DTC DETECTION LOGIC B

CONSULT-III display de-

DTC DTC Detection Condition Possible cause
scription C
When detecting error during the initial diagnosis of CAN control-
U1010 CONTROL UNIT (CAN) BCM
ler of BCM.

Diagnosis Procedure INFOID:0000000001451486

D

1. REPLACE BCM
E
When “DTC:U1010” is detected, replace BCM.

>> Replace BCM. Refer to BCS-57, "Removal and Installation of BCM". F

Special Repair Requirement INFOID:0000000001451487

1. ADDITIONAL SERVICE WHEN REPLACING BCM G

H
>> Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair
Requirement".

BCS

BCS-29
 POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure INFOID:0000000001451488

1. CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not fusing.

Terminal No. Signal name Fuses and fusible link No.

22 9 (10A)
72 8 (10A)
Battery power supply
74
G (40A)
79
24 Ignition power supply 55 (10A)
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO >> GO TO 2.
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.

Terminals
Ignition switch position
(+)
BCM (−)
OFF ACC ON
Connector Terminal
Battery Battery Battery
22 ALMIA0188ZZ
voltage voltage voltage
M18
Approx. Approx. Battery
24
0V 0V voltage
Ground
72
Battery Battery Battery
M20 74
voltage voltage voltage
79
Is the measurement value normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.

BCM
Continuity
Connector Terminal
Ground
M18 2
Yes
M20 70
Does continuity exist?
YES >> INSPECTION END
NO >> Repair or replace harness. ALMIA0189ZZ

BCS-30
 COMBINATION SWITCH INPUT CIRCUIT
< COMPONENT DIAGNOSIS >
COMBINATION SWITCH INPUT CIRCUIT
A
Diagnosis Procedure INFOID:0000000001451489

1. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN B

1. Turn ignition switch OFF.
2. Disconnect BCM and combination switch.
3. Check continuity between BCM harness connector and combi- C
nation switch harness connector.

BCM Combination switch D

System Continuity
Connector Terminal Connector Terminal
INPUT 1 9 1
E
INPUT 2 28 2
M20 M28 ALMIA0190ZZ
INPUT 3 8 3 Yes
(A) (B)
INPUT 4 27 4 F
INPUT 5 7 5
Does continuity exist?
YES >> GO TO 2 G
NO >> Repair or replace harness.
2. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT H
Check for continuity between BCM harness connector and ground.

BCM I
System Continuity
Connector Terminal
INPUT 1 9
J
INPUT 2 28 Ground
INPUT 3 M20 8 No
INPUT 4 27 K
INPUT 5 7 ALMIA0191ZZ

Does continuity exist?

YES >> Repair or replace harness. L
NO >> GO TO 3
3. CHECK BCM OUTPUT VOLTAGE BCS
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM harness connector and ground.
N

Terminals
(+) (−) Voltage O
System
BCM (Approx.)

Connector Terminal
INPUT 1 9 P
ALMIA0192ZZ
Ground
INPUT 2 28
Refer to BCS-
INPUT 3 M20 8 35, "Refer-
ence Value".
INPUT 4 27
INPUT 5 7
Is the measurement value normal?

BCS-31
 COMBINATION SWITCH INPUT CIRCUIT
< COMPONENT DIAGNOSIS >
YES >> GO TO 4
NO >> Replace BCM. Refer to BCS-57, "Removal and Installation of BCM".
4. CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-34, "Description".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-57, "Removal and Installation of BCM".
NO >> Replace the combination switch (applicable parts). Refer to EXL-101, "Removal and Installation".
Special Repair Requirement INFOID:0000000001451490

1. ADDITIONAL SERVICE WHEN REPLACING BCM

>> Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair
Requirement".

BCS-32
 COMBINATION SWITCH OUTPUT CIRCUIT
< COMPONENT DIAGNOSIS >
COMBINATION SWITCH OUTPUT CIRCUIT
A
Diagnosis Procedure INFOID:0000000001451491

1. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN B

1. Turn ignition switch OFF.
2. Disconnect BCM and combination switch.
3. Check continuity between BCM harness connector and combi- C
nation switch harness connector.

BCM Combination switch D

System Continuity
Connector Terminal Connector Terminal
OUTPUT 1 13 6
E
OUTPUT 2 33 7
ALMIA0193ZZ
OUTPUT 3 M20 14 M28 10 Yes
OUTPUT 4 34 9 F
OUTPUT 5 15 8
Does continuity exist?
YES >> GO TO 2 G
NO >> Repair or replace harness.
2. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT H
Check for continuity between BCM harness connector and ground.

BCM I
System Continuity
Connector Terminal
OUTPUT 1 13
J
OUTPUT 2 33 Ground
OUTPUT 3 M20 14 No
OUTPUT 4 34 K
OUTPUT 5 15 ALMIA0194ZZ

Does continuity exist?

YES >> Repair or replace harness. L
NO >> GO TO 3
3. CHECK COMBINATION SWITCH BCS
Check combination switch. Refer to BCS-34, "Description".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-57, "Removal and Installation of BCM". N
NO >> Replace combination switch (applicable parts). Refer to EXL-101, "Removal and Installation".
Special Repair Requirement INFOID:0000000001451492
O
1. ADDITIONAL SERVICE WHEN REPLACING BCM
P

>> Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair
Requirement".

BCS-33
 COMBINATION SWITCH
< COMPONENT DIAGNOSIS >
COMBINATION SWITCH
Description INFOID:0000000001451493

COMBINATION SWITCH MATRIX

Combination switch consists of INPUT circuit and OUTPUT circuit.
Combination switch circuit

JPMIA0121GB

Combination switch INPUT-OUTPUT system list

System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 RR WASHER — HEADLAMP 2 HI BEAM
INPUT 4 RR WIPER INT INT VOLUME 3 AUTO LIGHT — TAIL LAMP
INPUT 5 INT VOLUME 2 RR WIPER RR FOG FR FOG —
NOTE:
Headlamp has a dual system switch.

Diagnosis Procedure INFOID:0000000001451494

1. CHECK LIGHT & TURN SIGNAL SWITCH

Check operation with normal light & turn signal switch installed.
Does it operate normally?
YES >> Replace light & turn signal switch. Refer to EXL-101, "Removal and Installation".
NO >> GO TO 2
2. CHECK WIPER & WASHER SWITCH
Check operation with normal wiper & washer switch installed.
Does it operate normally?
YES >> Replace wiper & washer switch. Refer to WW-76, "Removal and Installation".
NO >> GO TO 3
3. CHECK SWITCH BASE (SPIRAL CABLE)
Check operation with normal switch base (spiral cable) installed.
Does it operate normally?
YES >> Replace switch base (spiral cable). Refer to SR-7, "Removal and Installation".
NO >> Combination switch is normal.

BCS-34
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001451495
B

VALUES ON THE DIAGNOSIS TOOL

C
Monitor Item Condition Value/Status
A/C switch OFF OFF
AIR COND SW
A/C switch ON ON D
Outside of the room is dark OFF
AUT LIGHT SYS
Outside of the room is bright ON
E
Lighting switch OFF OFF
AUTO LIGHT SW
Lighting switch AUTO ON
Back door closed OFF F
BACK DOOR SW
Back door opened ON
BATTERY VOLT
NOTE:
Ignition switch ON
Approximately the same as power G
Diesel engine models supply voltage
only
Door lock/unlock switch does not operate OFF H
CDL LOCK SW
Press door lock/unlock switch to the LOCK side ON
Door lock/unlock switch does not operate OFF
CDL UNLOCK SW
Press door lock/unlock switch to the UNLOCK side ON I
Passenger door closed OFF
DOOR SW-AS
Passenger door opened ON
J
Driver door closed OFF
DOOR SW-DR
Driver door opened ON
Rear LH door closed OFF K
DOOR SW-RL
Rear LH door opened ON
Rear RH door closed OFF
DOOR SW-RR L
Rear RH door opened ON
Fan switch ON (when engine coolant is
cool)
BCS
NOTE: OFF
Depending on the ambient tempera-
ture, battery voltage, etc.
ELEC PWR CUT The current status maintained with the N
FREEZ
NOTE: signal from ECM received.
Engine running
Diesel engine models
• Fan switch OFF
only
• Fan switch ON after engine warming O
UP
NOTE: INHBT
Depending on the engine coolant
temperature, ambient temperature, P
battery voltage, etc.
ENG COOLNT T
NOTE: Approximately the same as engine
Engine running
Diesel engine models water temperature
only

BCS-35
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
ENGINE RPM
NOTE: Approximately the same as tachom-
Engine running
Diesel engine models eter reading
only
Engine stopped OFF
ENGINE RUN
Engine running ON
Engine stopped STOP
ENGINE STATUS
NOTE: While the engine stalls STALL
Diesel engine models Engine running RUN
only
At engine cranking CRA
Fan switch OFF OFF
FAN ON SIG
Fan switch ON ON
Front fog lamp switch OFF OFF
FR FOG SW
Front fog lamp switch ON ON
Front washer switch OFF OFF
FR WASHER SW
Front washer switch ON ON
Front wiper switch OFF OFF
FR WIPER LOW
Front wiper switch LO ON
Front wiper switch OFF OFF
FR WIPER HI
Front wiper switch HI ON
Front wiper switch OFF OFF
FR WIPER INT
Front wiper switch INT ON
Any position other than front wiper stop position OFF
FR WIPER STOP
Front wiper stop position ON
When hazard switch is not pressed OFF
HAZARD SW
When hazard switch is pressed ON
Lighting switch OFF OFF
LIGHT SW 1ST
Lighting switch 1st ON
Headlamp switch OFF OFF
H/L SW POS
Headlamp switch 1st ON
High beam switch OFF OFF
HI BEAM SW
High beam switch HI ON
Close the hood
NOTE: OFF
HOOD SW Vehicles without theft warning system are OFF-fixed
Open the hood ON
NOTE:
H/L WASH SW OFF
The item is indicated, but not monitored
Ignition switch OFF or ACC OFF
IGN ON SW
Ignition switch ON ON
Ignition switch OFF or ACC OFF
IGN SW CAN
Ignition switch ON ON
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
LOCK button of Intelligent Key is not pressed OFF
I-KEY LOCK1
LOCK button of Intelligent Key is pressed ON

BCS-36
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
UNLOCK button of Intelligent Key is not pressed OFF
I-KEY UNLOCK1
UNLOCK button of Intelligent Key is pressed ON
Mechanical key is removed from key cylinder OFF B
KEY SW2
Mechanical key is inserted to key cylinder ON
LOCK button of key fob is not pressed OFF
KEYLESS LOCK2 C
LOCK button of key fob is pressed ON
UNLOCK button of key fob is not pressed OFF
KEYLESS UNLOCK2
UNLOCK button of key fob is pressed ON
D
Light & rain sensor is in normal condition OK
LIT-SEN FAIL
Light & rain sensor is with internal error NOTOK
• Ignition switch OFF or ACC E
OFF
OIL PRESS SW • Engine running
Ignition switch ON ON
OUT SIDE TEMP F
Approximately the same as outside
NOTE: Ignition switch ON
air temperature
Diesel engine models
Other than lighting switch PASS OFF G
PASSING SW
Lighting switch PASS ON
Return to ignition switch to LOCK position OFF
PUSH SW1 H
Press ignition switch ON
Rear window defogger switch OFF OFF
REAR DEF SW
Rear window defogger switch ON ON I
RKE LOCK AND NOTE: OFF
UNLOCK2 The item is indicated, but not monitored ON
J
Rear fog lamp switch OFF OFF
RR FOG SW
Rear fog lamp switch ON ON
Rear washer switch OFF OFF K
RR WASHER SW3
Rear washer switch ON ON
Rear wiper switch OFF OFF
RR WIPER INT3 L
Rear wiper switch INT ON
Rear wiper switch OFF OFF
RR WIPER ON3
Rear wiper switch ON ON
BCS
Rear wiper stop position OFF
3
RR WIPER STOP
Other than rear wiper stop position ON
Lighting switch OFF OFF N
TAIL LAMP SW
Lighting switch 1ST ON
When back door opener switch is not pressed OFF
TRNK OPNR SW O
When back door opener switch is pressed ON
Turn signal switch OFF OFF
TURN SIGNAL L
Turn signal switch LH ON P
Turn signal switch OFF OFF
TURN SIGNAL R
Turn signal switch RH ON

NOTE: OFF
UNLOCK WITH DR
The item is indicated, but not monitored ON
VEHICLE SPEED While driving Equivalent to speedometer reading

BCS-37
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
1: With Intelligent Key
2: With remote keyless entry system
3: Hatchback

Terminal Layout INFOID:0000000001538883

TERMINAL LAYOUT

ALMIA0185ZZ

BCS-38
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Physical Values INFOID:0000000001538886

A
PHYSICAL VALUES
CAUTION:
• Check combination switch system terminal waveform under the loaded condition with lighting B
switch, turn signal switch and wiper switch OFF is not to be fluctuated by being overloaded.
• Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter-
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT -III. Refer to C
BCS-24, "COMB SW : CONSULT-III Function (BCM - COMB SW)".
• BCM reads the status of the combination switch at 10 ms internal normally. Refer to BCS-7, "System
Description".
D
Terminal No. Description
(Wire color) Reference Value
Input/ Condition
Signal name (Approx.)
+ − Output E
2
Ground Ground — — 0V
(B)
Insert mechanical key into ignition key cylin- F
Battery voltage
3 der
Ground Key switch Output
(G) Remove mechanical key from ignition key
0V
cylinder G
4 Rear window defog- Rear window Not pressed 5V
Ground Output
(W) ger switch defogger switch While pressing 0V
H
51 Back door opener Back door Not pressed Battery voltage
Ground Output
(V) switch opener switch Pressed 0V

52 Trunk opener Not pressed Battery voltage I

Ground Trunk opener switch Output
(V) switch Pressed 0V

6 Door lock/unlock Door lock/un- Not pressed 5V

Ground J
(GR) switch (Lock) Output lock switch Pressed to the lock side 0V

BCS

BCS-39
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4)

JPMIA0165GB

1.3V

Front fog lamp switch ON

(Wiper intermittent dial 4)

JPMIA0167GB

1.3V

7 Combination switch Combination Rear fog lamp switch ON

Ground Input
(LG) INPUT 5 switch (Wiper intermittent dial 4)

JPMIA0168GB

1.3V

Rear wiper switch ON

(Wiper intermittent dial 4)

JPMIA0169GB

1.3V

Any of the condition below

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 6
• Wiper intermittent dial 7
JPMIA0196GB

1.3V

BCS-40
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4) C

JPMIA0165GB

1.4V D

E
Lighting switch HI
(Wiper intermittent dial 4)
F
JPMIA0166GB

1.3V
G

8 Combination switch Combination Lighting switch 2ND

H
Ground Input
(V) INPUT 3 switch (Wiper intermittent dial 4)

JPMIA0167GB
I
1.3V

Rear wiper switch ON

K

JPMIA0169GB

1.3V L

Any of the condition below BCS

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3 N
JPMIA0196GB

1.3V
O

BCS-41
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

JPMIA0165GB

1.4V

Turn signal switch LH

JPMIA0167GB

1.3V

Combination
9 Combination switch switch
Ground Input Turn signal switch RH
(P) INPUT 1 (Wiper intermit-
tent dial 4)

JPMIA0166GB

1.3V

Front wiper switch LO

JPMIA0168GB

1.3V

Front washer switch ON

JPMIA0196GB

1.3V
OFF (When back door
Battery voltage
101 Back door closed)
Ground Back door switch Input
(Y) switch ON (When back door
0V
opened)

102 OFF (When trunk closed) Battery voltage

Ground Trunk switch Input Trunk switch
(Y) ON (When trunk opened) 0V

BCS-42
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value A
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF
0V B
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
Rear wiper switch INT C
13 Combination switch Combination (Wiper intermittent dial 4)
Ground Output
(V) OUTPUT 1 switch Any of the condition below
with all switch OFF D
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3 SKIA2167J
• Wiper intermittent dial 6 E
• Wiper intermittent dial 7
All switch OFF 0V
Lighting switch AUTO
F

Combination Rear fog lamp switch OFF

14 Combination switch switch
Ground Output Front wiper switch MIST
(L) OUTPUT 3 (Wiper intermit- G
tent dial 4) Front wiper switch INT

Front wiper switch LO H

SKIA2167J

All switch OFF 0V

Lighting switch 1ST I
Combination Lighting switch 2ND
15 Combination switch switch
Ground Output Lighting switch HI
(BR) OUTPUT 5 (Wiper intermit-
tent dial 4)
J
Turn signal switch RH
SKIA2167J
K
16 Depress the brake pedal Battery voltage
Ground Stop lamp switch Input
(R) Release the brake pedal 0V
Shift lever in reverse Battery voltage L
17
Ground Back up lamp signal Input
(Y) Other than above 0V
19 Input/
(L)
— CAN-H
Output
— — BCS

21 Room lamp timer Interior room OFF Battery voltage

Ground Output
(BR) control lamp ON 0V
N
22 Battery power sup-
Ground Input — Battery voltage
(P) ply
Rear wiper stop position 0V O

P
231 Ground Rear wiper auto stop Output
Ignition switch
(LG) ON Any position other than
rear wiper stop position

JPMIA0197GB

BCS-43
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value
Input/ Condition
Signal name (Approx.)
+ − Output

24 Ignition power sup- Ignition switch OFF or ACC 0V

Ground Input
(O) ply Ignition switch ON or START Battery voltage

25 Door lock/unlock Door lock/un- Not pressed 5V

Ground
(L) switch (Unlock) Output lock switch Pressed to the unlock side 0V

26 Not pressed
Ground Hazard switch Output Hazard switch
(L)

SKIA2239J

Pressed 0V

BCS-44
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4) C

JPMIA0165GB

1.4V D

E
Lighting switch AUTO
(Wiper intermittent dial 4)
F
JPMIA0167GB

1.3V
G

27 Combination switch Combination Lighting switch 1ST

H
Ground Input
(Y) INPUT 4 switch (Wiper intermittent dial 4)

JPMIA0166GB
I
1.3V

Rear wiper INT

(Wiper intermittent dial 4) K

JPMIA0167GB

1.3V L

BCS
Any of the condition below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 6 N
JPMIA0196GB

1.3V
O

BCS-45
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

JPMIA0165GB

1.4V

Lighting switch PASS

JPMIA0167GB

1.3V

Combination
28 Combination switch switch
Ground Input Lighting switch 2ND
(R) INPUT 2 (Wiper intermit-
tent dial 4)

JPMIA0166GB

1.3V

Front wiper switch INT

JPMIA0168GB

1.3V

Front wiper switch HI

JPMIA0196GB

1.3V
OFF (When driver door
Battery voltage
29 Driver door closed)
Ground Driver door switch Input
(BR) switch ON (When driver door
0V
opened)
OFF (When passenger
Battery voltage
30 Passenger door Passenger door door closed)
Ground Input
(SB) switch switch ON (When passenger
0V
door opened)

313 OFF Battery voltage

Ground A/C indicator Output A/C switch
(SB) ON 0V

BCS-46
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value A
Input/ Condition
Signal name (Approx.)
+ − Output

324 Door lock status indi- Door lock status ON Battery voltage
Ground
cator
Output
indicator
B
(LG) OFF 0V
All switch OFF
0V
(Wiper intermittent dial 4)
C
Front washer switch ON
(Wiper intermittent dial 4)
Rear wiper switch ON
D
(Wiper intermittent dial 4)
33 Combination switch Combination
Ground Output
(G) OUTPUT 2 switch Rear washer switch ON
(Wiper intermittent dial 4)
E
Any of the condition below
with all switch OFF
• Wiper intermittent dial 1 SKIA2167J
• Wiper intermittent dial 5 F
• Wiper intermittent dial 6
All switch OFF 0V
Lighting switch 2ND G
Combination Lighting switch PASS
34 Combination switch switch
Ground Output Front fog lamp switch ON
(GR) OUTPUT 4 (Wiper intermit- H
tent dial 4)
Turn signal switch LH
SKIA2167J I
353, 7 ON 0V → 5V
Ground Sensor ground Output Ignition switch
(BR) OFF 0V
J
367 Ambient sensor sig- ON 0V → 5V
Ground Input Ignition switch
(V) nal OFF 0V
Just after Insert mechanical key K
385 Ground NATS antenna amp.
Input/ Insert mechanical key into ignition key cylin-
into ignition key cylinder. Pointer
(V) Output der
of tester should move
39 Input/ L
— CAN-L — —
(P) Output

453 ON 0V
Ground Intake sensor Input Ignition switch
(GR) OFF Battery voltage BCS
ON 0V
475 Ground Security indicator Output
Security indica- Blinking
Battery voltage → 0V
(GR) tor (every 2.4 seconds) N
OFF Battery voltage

48 Ignition switch START Battery voltage

Ground Start power supply Input O
(W) Other than above 0V

49 Front demist vent Front demist ON 0V → 5V

Ground Input
(R) switch vent switch OFF 0V P
50 Not pressed Battery voltage
Ground Fan switch Output Fan switch
(P) Pressed 0

517 PTC heater 3 ON 0V

Ground PTC relay 3 control Output Ignition ON
(L) PTC heater 3 OFF Battery voltage

BCS-47
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value
Input/ Condition
Signal name (Approx.)
+ − Output

527 PTC heater 2 ON 0V

Ground PTC relay 2 control Output Ignition ON
(GR) PTC heater 2 OFF Battery voltage

58 Lock Battery voltage

Ground Door unlock sensor Input Driver door
(Y) Unlock 0V
OFF (When rear door LH
Battery voltage
59 Rear door closed)
Ground Rear door switch LH Input
(O) switch LH ON (When rear door LH
0V
opened)
OFF (When rear door RH
Battery voltage
60 Rear door closed)
Ground Rear door switch RH Input
(GR) switch RH ON (When rear door RH
0V
opened)

613 Not pressed Battery voltage

Ground A/C switch Output A/C switch
(O) Pressed 0V
Ignition switch OFF Battery voltage

63 Light & rain sensor

Ground Output
(R) serial link Ignition switch ON

MKIB0173E

647 PTC heater 1 ON 0V

Ground PTC relay 1 control Output Ignition ON
(O) PTC heater 1 OFF Battery voltage
Turn signal switch OFF 0V

65 Ignition switch
Ground Turn signal LH Output
(V) ON Turn signal switch LH

SKIA1120J

Turn signal switch OFF 0V

66 Ignition switch
Ground Turn signal RH Output
(W) ON Turn signal switch RH

SKIA1120J

Door unlock (pas- Pressed to the unlock side Battery voltage

67 Door lock/un-
Ground senger and rear Output
(G) lock switch Pressed to the lock side 0V
doors)

681 Back door lock actu- Back door Pressed Battery voltage
Ground Output
(R) ator opener switch Not pressed 0V

682 Trunk release sole- Trunk lid opener Pressed Battery voltage
Ground Output
(R) noid switch Not pressed 0V

BCS-48
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Reference Value A
Input/ Condition
Signal name (Approx.)
+ − Output
Lighting switch Rear fog lamp switch OFF 0V
69 1ST and front B
Ground Rear fog lamp Output
(G) fog lamp switch Rear fog lamp switch ON Battery voltage
ON
70 C
Ground Ground — — 0V
(B)

711 Rear wiper switch OFF 0V

Ground Rear wiper motor Output
(V) Rear wiper switch ON Battery voltage D
72 Battery power sup-
Ground Input — Battery voltage
(LG) ply
After passing the interior room lamp battery E
0V
73 Interior room lamp saver operation time
Ground Output
(R) power supply Any other time after passing the interior room
Battery voltage
lamp battery saver operation time F
74 Battery power sup-
Ground Input — Battery voltage
(Y) ply
When lock button of keyfob or Intelligent Key G
0V
75 4 is not pressed
Ground Super lock Output
(V) When lock button of keyfob or Intelligent Key
Battery voltage
is pressed H
76 Door lock/un- Pressed to the unlock side Battery voltage
Ground Driver door unlock Output
(G) lock switch Pressed to the lock side 0V
Pressed to the unlock side 0V
I
77 Door lock/un-
Ground Door lock (All) Output
(SB) lock switch Pressed to the lock side Battery voltage

78 Power window pow- OFF or ACC 0V J

Ground Output Ignition switch
(L) er supply ON Battery voltage
79 Battery power sup-
Ground Input — Battery voltage
(Y) ply K
1: Hatchback
2: Sedan
3: Manual A/C L
4: Superlock
5: Remote keyless entry
6: Intelligent Key BCS
7: LHD diesel

BCS-49
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram INFOID:0000000001451496

ALMWA0067GB

BCS-50
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

BCS

ALMWA0068GB

BCS-51
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

ALMWA0069GB

BCS-52
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

BCS

ALMIA0320GB

DTC Inspection Priority Chart INFOID:0000000001451498 P

Priority DTC
• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)

BCS-53
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
DTC Index INFOID:0000000001451499

NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
• PAST: Displays when there is a malfunction that is detected in the past and stored.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.

CONSULT display TIME Fail-safe Refer to

No DTC is detected.
further testing — — — —
may be required.
U1000: CAN COMM CIRCUIT 0 1 - 39 — BCS-28
U1010: CONTROL UNIT (CAN) 0 1 - 39 — BCS-29

BCS-54
 COMBINATION SWITCH SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table INFOID:0000000001451500
B

1. Perform “Data Monitor” of CONSULT-III to check for any malfunctioning item.

2. Check the malfunction combinations. C
Malfunction item: ×

Data monitor item

D
HEAD LAMP SW 1

HEAD LAMP SW 2

RR WASHER SW
AUTO LIGHT SW

FR WASHER SW
TURN SIGNAL R

TURN SIGNAL L

FR WIPER LOW
TAIL LAMP SW

RR WIPER INT
RR WIPER ON
FR WIPER INT
PASSING SW

FR WIPER HI

INT VOLUME
HI BEAM SW

RR FOG SW
FR FOG SW
Malfunction combi-
nation
E

× × × × A F
× × × × B
× × × × C
G
× × × × D
× × × × E
× × × F H
× × × × G
× × × × H
I
× × × × I
× × × × J
Combinations other than those above K J
All Items L
If only one item is detected or the item is not applicable to the combinations A to L M
K
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.

Malfunction
Malfunctioning part Repair or replace L
combination
A Combination switch INPUT 1 circuit
B Combination switch INPUT 2 circuit BCS
Inspect the combination switch input circuit applicable to the malfunctioning
C Combination switch INPUT 3 circuit
part. Refer to BCS-31, "Diagnosis Procedure".
D Combination switch INPUT 4 circuit
E Combination switch INPUT 5 circuit N
F Combination switch OUTPUT 1 circuit
G Combination switch OUTPUT 2 circuit
Inspect the combination switch output circuit applicable to the malfunction- O
H Combination switch OUTPUT 3 circuit
ing part. Refer to BCS-33, "Diagnosis Procedure".
I Combination switch OUTPUT 4 circuit
J Combination switch OUTPUT 5 circuit P
Light and turn signal switch or front wip-
K Refer to BCS-34, "Description".
er and washer switch
L BCM Replace BCM. Refer to BCS-57, "Removal and Installation of BCM".
Light and turn signal switch or front wip-
M Replace the switch that cannot be operated.
er and washer switch

BCS-55
 PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000001523305

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

BCS-56
 BCM (BODY CONTROL MODULE)
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR A
BCM (BODY CONTROL MODULE)
Removal and Installation of BCM INFOID:0000000001523223
B
NOTE:
The LHD model shown, RHD model similar.
C
REMOVAL
1. Remove the glove box. Refer to IP-11, "Removal and Installation".
2. Remove the BCM screws, disconnect the connectors and D
remove the BCM (1).

WKIA5672E G
INSTALLATION
Installation is in the reverse order of removal.
NOTE: H
• When replacing BCM, it must be configured. Refer to BCS-4, "CONFIGURATION : Special Repair Require-
ment".
• When replacing BCM, perform initialization of NATS system and registration of all NATS ignition key IDs. I
Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
ment".
• When replacing BCM, if new BCM does not come with keyfobs attached, all existing keyfobs must be re-reg-
istered. J

BCS

BCS-57