Testing Procedures for Power

Engineering

Contents

[hide]

 1 Testing Procedures for Power Engineering

o 1.1 Metallurgical Analysis

o 1.2 Testing According to IEC/EN

 1.2.1 Electrical Life

 1.2.2 Temperature Rise

 1.2.3 Analysis of the Switching Sequence

 1.2.4 Switching Capacity

o 1.3 Testing According to UL and CSA

 2 References

Testing Procedures for Power Engineering

The testing of electrical contacts for power engineering applications serves on the one hand the continuous
quality assurance, on the other one the new and improvement development efforts for contact materials. To
optimize the contact and switching performance contact materials and device designs have to complement
each other. The success of such optimizing is proven through switching tests.

The assessment of contact materials is performed using metallurgical test methods as well as switching tests in
model test set-ups and in commercial switching devices. While physical properties such as melting and boiling
point, electrical conductivity, etc. are fundamental for the selection of the base metals and the additional
components of the materials, they cannot provide a clear indication of the contact and switching behavior.
Metallurgical evaluations and tests are used primarily for determining material and working defects. The actual
contact and switching behavior can however only be determined through switching tests in a model switch or
preferably in the final electromechanical device.

Model testing devices offer the possibility of quick ratings of the make and break behavior and give a
preliminary classification of potential contact materials. Since such tests are performed under ideal conditions
they cannot replace switching tests in actual devices.

The electrical testing of commercially produced switching devices should follow DIN EN or IEC standards and
rules. Special test standards exist for each type of switching device which are differentiated by:
  Make capacity

 Break capacity

 Electrical life

 Temperature rise

The following chapters are limited to metallurgical analysis and the testing of the most important properties of
switching devices such as electrical life, temperature rise, and switching capacity.

Metallurgical Analysis
The main characteristic for the appraisal of contact materials for power engineering is the optical evaluation of
their microstructure in a metallographic mount. This provides a picture of the internal structure of the materials.
It allows detecting structural in-homogeneity, grain boundary enrichments, cracks, material separations, or
defects in the brazing interface. The metallographic view is however limited to the one two-dimensional plain in
which the mounting cut was made.

Figure 1 shows the microstructure of a Ag/CdO contact material after being affected by electrical arcing. In the
lower part the starting material structure is visible. In the upper part the de-mixing of the composite material
through the effects of the switching arc is clearly demonstrated. This “switching structure” shows in certain
areas depletion of metal oxide which increases the probability of contact welding during subsequenbt make
operations. Additional analysis by X-ray probing in a scanning electron microscope (SEM) allows the micro
analysis of the elements present in the contact surface region.

Microstructure of a powder metallurgical Ag/CdO material after being affected by intense electrical arcing

Testing According to IEC/EN

Electrical Life

The electrical life of contactors, motor switches, and auxiliary current switches used in power engineering is
classified into use categories which are shown in Table 1.

The making and breaking currents for tests IEC/EN 60947-4-1 are shown in Table 2 for the different use
categories.

The electrical life of a motor switch is influenced primarily by arc erosion which is generated during make and
break arcs on the contact surface. During AC-3 testing, for which the make current is six time the nominal rated
current, the arc erosion is mainly caused by the make arcs, especially if frequent contact bounces > 2 ms
occur. Therefore the bounce characteristic of switching devices primarily used for “normal” use in switching on
and off electrical motors is of critical importance. If make and break currents are the same, as in the ultilisation
categories AC-1 and AC-4, the break erosion dominates the arc erosion so much that make erosion can be
neglected.

Table 1: Important Use Categories and Their Typical Applications for Contactors and Power Switches
Contactors, Motor Starters according to IEC/N60947-4-1

Type of current Utilisation category T

Alternating current (AC) AC-1 Non-inductive or slightly inductive loads, resistance furnaces

AC-2 Slip ring motors: starting, switch-off

AC-3 Squirrel-cage motors: starting, switch-off, switch-off during runn

AC-4 Sqirrel-cage motors: starting, plugging, reversing, inching

Direct current (DC) DC-1 Non-inductive or slightly inductive loads, resistance furnaces

DC-3 Shunt motors: starting, plugging, reversing, inching, dynamic bra

DC-5 Series motors: starting, plugging, reversing, inching, dynamic bra

Auxiliary Current Switches according to IEC/EN 160947-5-1

Type of current Utilisation category T

Alternating current (AC) AC-12 Controlling resistive semiconductor loads in feed circuits of optoe

AC-14 Controlling small electromagnetic loads (72 VA max)

AC-15 Controlling electromagnetic loads (> 72 VA)

Direct Current (DC) DC-12 Controlling resistive semiconductor loads in feed circuits of optoe

DC-13 Controlling of electro magnets under direct current

DC-14 Controlling of electromagnetic loads under direct current with po

The electrical life for the utilization categories AC-3, DC-3, and DC-5 must be at a minimum 5% of the
mechanical lifetime of a switching device. The conditions for make and break tests of auxiliary current switches
and control circuit devices are described in IEC/EN 60947-5-1. Usually the electrical life of auxiliary switches is
of lesser importance since these devices see only smaller loads. Under certain conditions however
requirements for make and beak capacity can be as high as 10 times the nominal current. This results in very
severe requirements on the dielectric strength and recovery voltage of the arc affected region immediately after
arcing.

Table 2: Verification of Electrical Life Conditions for Make and Break Tests of Contactors and Motor
Starters by Utilization Category
Ultilisation Category Current Make operation

Ie/A I/Ie U/Ue cos

AC-1 Alle Werte 1 1 0.95

AC-2 Alle Werte 2.5 1 0.65

Ie ≤ 17 6 1 0.65
AC-3
Ie > 17 6 1 0.35

Ie ≤ 17 6 1 0.65
AC-4
Ie > 17 6 1 0.35

Ie/A I/Ie U/Ue L/R [m

DC-1 All values 1 1 1

DC-3 All values 2.5 1 2

DC-5 All values 2.5 1 7.5

Ie = Rated operational current

I = Make (ON) current
Ic = Break (OFF) current

Ue = Rated operational voltage

U = Voltage
Ur = Recovery voltage
AC-3 contact arc erosion of two differently produced Ag/SnO 2contact materials in a 37 kW contactor 1 Ag/SnO2 88/12,
produced by conventional powder metallurgy with MoO3 additive, extruded 2 Ag/SnO2 88/12, powder manufacturing by the
reaction-spray process with CuO and Bi2 O3additives, extruded

Temperature Rise

Testing for temperature rise is required only for switching devices in the new stage. During use however over
the entire life of the device no damages due to temperature rise are allowed in the device or at ist terminal
points.

Maximum movable bridge temperature rise for different contact materials in a 132 kW contactor after high load (AC-4)
switching 1 Ag/CdO 88/12 sintered and extruded 2Ag/SnO27.5In2O32.5 internally oxidized 3 Ag/SnO2 88/12 sintered and
extruded 4 Ag/SnO2 11.5 WO3 0.5 sintered and extruded 5Ag/SnO2 11.6 MO4 0.4 sintered and extruded

For the assessment of contact materials a temperature rise test is frequently performed after a specified
number of switching operations accompanied by arcing Figure 2. The most important characteristic is the
measured temeperature rise of the movable bridge contacts. If a certain upper limit of temperature is reached,
adjacent plastic components may be irreversibly damaged.

Analysis of the Switching Sequence

In switching devices, which are actuated by AC actuator magnets, the contact parts can close and open
synchronously at a specific phase angle relative to the voltage-zero of the supply voltage. Of similar importance
is the sequence of closing and opening of the contacts with regards to the three phases. The closing and
opening delays define at which time delay after the first phase (or pole) the other phases close and open.

Relevant experiments have shown that combined effects of synchronism, phase sequence and switching delay
can, under severe adverse conditions, lead to extreme damage, especially on at least one of the phases or
poles. They are the cause of early failure of this phase and therefore the complete switching device and can
happen as early as after only 30% of the normally expected lifetime. Because of variations in the mechanical
characteristics of switching devices from manufacturing processes life testing cannot be performed on one
device alone. Only statistical analysis of tests from multiple device samples can be used as reliable results.
Such a procedure is however time consuming and costly. If however every single switching operation during a
test is monitored for bounce behavior, on- and off-switching synchronization and related phase sequencing and
phase delays, the arc moving behavior, and especially arc energy which is transferred during make and break
arcing to the contact pieces, and then these data are properly analyzed, is it possible to assess a specific
contact material from a test in only one device alone. Only statistical analysis of tests from multiple device
samples can be used as reliable results. Such a procedure is however time consuming and costly. If however
every single switching operation during a test is monitored for bounce behavior, on- and offswitching
synchronization and related phase sequencing and phase delays, the arc moving behavior, and especially arc
energy which is transferred during make and break arcing to the contact pieces, and then these data are
properly analyzed, is it possible to assess a specific contact material from a test in only one device.

Switching Capacity

The main requirement for low voltage power switches is the withstanding of high short circuit currents. The
short circuit switching capacity of power switches is determined in tests according to IEC/EN 60947-2 Table 3.
These test differentiate between the maximum short circuit current switching capacity (ultimate current limit)
ICU and the operational (or service) short circuit current capacity ICS .

When specifying ICU it must be guaranteed that short circuit current up to the maximum limit value can be
interrupted safely. After its occurrence it must be possible to switch on one additional time onto the not yet
eliminated short circuit and again interrupt this short circuit current again safely. The switch does not have to be
functional any more after this second interruption. A switch specified for ICS must still be capable to protect the
circuit and be further usable within certain limitations.

To safely withstand short circuit currents high requirements are imposed on the weld resistance of the materials
used for the mating contacts. During short circuit switching the contact force between the contacts pairing is
reduced by electromagnetic forces. Above a certain device specific current value the contacts will separate.
This generates an electrical arc with contact material melting at its root points. During the next closing of the
contacts this can cause contact welding, prohibiting the opening of the contacts during a subsequent short
circuit and therefore eliminating the safety function of the switching device.
Table 3: Testing for the Short Circuit Breaking Capacity of Low Voltage Power Switches According to
IEC/EN 60947-2 (Shortened Summary)
Test characteristics Rated ultimate short circuit breaking capacity ICU

Ue
cosn depends on value of current I in kA, i.e
6 < l ≤ 10 cosφ 0.5
Test conditions 10 < l ≤ 20 cosφ 0.3
20 < l ≤ 50 cosφ 0.25
50 < l cosφ 0.2

Testing sequence O - t - CO

Subsequent isolation test 2 x Ue, with min. 1.000 V

Subsequent temperature rise test

Ue = Rated operational voltage

U = Current
O = Switch off
T = Pause
CO = Switch on and off

Testing According to UL and CSA

The test standards for North America according to UL (USA) and CSA (Canada) differ in part substantially from
those of the IEC and harmonized European EN standards. In the US and Canada the standards differentiate
between switchgear for power distribution, for example low voltage circuit breakers and power switches
covered by UL 489 (UL = Underwriters Laboratories) and CSAC22.2 No. 5-02 (CSA = Canadian Standard
Association) and those for industrial switching devices, for example contactors covered by UL 508 and CSA-
C22.2 No. 14 respectively. For industrial controls contactors and other switching devices are often classified in
the USA according to NEMA (National Electrical Manufacturers Association) current rating. North American
standards emphasize the prevention of fires and therefore have high limit requirements on temperature rise.
They also require larger air and creep gaps than those of IEC, which leads to significant differences in the
design of the switches and their contact systems.

References

References

Navigation menu
  Create account

 Log in

 Discussion
 View
 View source
 History
Go Search

Powered by

Navigation
 Table of Contents
 Contents
 Contact-Wiki Guide
 Recent changes
 Random page
 Create new article
 Contact DODUCO
In other languages
 Deutsch
 This page was last modified on 22 September 2014, at 23:08.
 This page has been accessed 3,514 times.

 Privacy policy

 About Doduco

 Disclaimers

 Impressum
Scroll To Top