Scribd Logo
Upload

Welcome to Scribd!

  • 65 views

    InteliATS NT 2.5 New Features r1

    Uploaded by

    fernando lozano
    InteliATS NT 2.5 New Features r1

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    InteliATS NT 2.5 New Features r1

    Uploaded by

    fernando lozano
    65 views7 pages
    InteliATS NT 2.5 New Features r1

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    InteliATS NT 2.5 New Features r1

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    65 views7 pages

    InteliATS NT 2.5 New Features r1

    Uploaded by

    fernando lozano
    InteliATS NT 2.5 New Features r1

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 7

    InteliATSNT

    Automatic Transfer Switch


    Controller

    SW version 2.5
    1 General information 2
    2 Changes in the version 2.5 3
    3 Related information 5
    4 Notes 7

    Copyright © 2016 ComAp a.s.


    Written by Michal Slavata
    Prague, Czech Republic
    ComAp a.s., Kundratka 2359/17,
    180 00 Praha 8, Czech Republic
    Tel: +420 246 012 111, Fax: +420 266 316 647
    E-mail: [email protected], www.comap.cz New Features List
    1 General information
    1.1 Version information
    Repair of evaluation of state of sources. Also repair of some small bugs.

    1.2 Clarification of notation


    Note: This type of paragraph calls readers attention to a notice or related theme.

    IMPORTANT: This type of paragraph highlights a procedure, adjustment etc., which can cause a
    damage or unproper function of the equipment if not performed correctly and may not be clear at
    first sight.

    Example: This type of paragraph contains information that is used to illustrate how a specific function
    works.

    Inteli ATS 2.5 New Features List 2


    2 Changes in the version 2.5
    2.1 Repairs
    Alarms on binary inputs 5, 6, 7 (PWR version only)
    Alarms were not recorded in alarmlist. Now when configured alarms are active, they are recorded in
    alarmlist.
    Active Call Fail for channel 2 (PWR version only)
    When email address was adjusted only for email address 1 and email address two was blank, then
    ActCallCH2Fail was activated when email was send. Now alarm is not evaluated when only email
    address 1 is adjusted.
    Source evaluation - Mains healthy binary input (STD and PWR version)
    Following changes were made:

    GenReadyToLoad binary input


    Indicates when the gen-set is ready to take over the load. Conditions for successful gen-set start and readiness
    to take over the load can be evaluated from the voltage and the frequency of the generator or from the state of
    GenReadyToLoad input or from both sources. The conditions have to be fulfilled during time defined by Basic
    Settings: Max Start Del setpoint (which can be even unlimited).
    Note: When this binary input isn’t configured, the setpoint GenerProtect is adjust to value ENABLED and this
    value can’t be changed.

    MainsHealthy
    Indicates when the mains is ready to take over the load. Conditions for take over the load can be evaluated from
    the voltage and the frequency of the mains or from the state of MainsHealthy input or from both sources.
    Note: When this binary input isn’t configured, the setpoint MainsProtect is adjust to value ENABLED and this
    value can’t be changed.

    GenerProtect [ENABLED/DISABLED]
    Setpoint enable or disable evaluating of generator voltage and frequency values.
    ENABLED: Values are used for evaluating of state of source and for protections.
    DISABLED: Values are not used for evaluating of state of source and for protections. If terminal for
    measurement are connected to controller, values are just shown on measuring screen.
    Note: When binary input GenReadyToLoad isn’t configured, the setpoint GenerProtect is adjust to value
    ENABLED and this value can’t be changed.

    MainsProtect [ENABLED/DISABLED]
    Setpoint enable or disable evaluating of mains voltage and frequency values.
    ENABLED: Values are used for evaluating of state of source and for protections.
    DISABLED: Values are not used for evaluating of state of source and for protections. If terminal for
    measurement are connected to controller, values are just shown on measuring screen.
    Note: When binary input MainsHealthy isn’t configured, the setpoint MainsProtect is adjust to value ENABLED
    and this value can’t be changed.

    Inteli ATS 2.5 New Features List 3


    Comms Settings (STD version only)
    communication isn’t supported in standard version of IA-NT, this group of setpoint was removed from
    controller
    IMPORTANT: Communication via modules IL-NT GPRS and IB-Lite was never supported in IA-NT
    STD. In FW 2.4 it was bug.

    Inteli ATS 2.5 New Features List 4


    3 Related information
    3.1 Available files
    Firmware (*.Mhx)
    For IA-NT STD up to 1.3 For IA-NT STD For IA-NT PWR
    IA-NT-STD_HW1.3-2.5.0.3.mhx IA-NT-STD-2.5.0.3.mhx IA-NT-PWR-2.5.0.3.mhx

    Table 3.1 Available firmware

    Archives (*.ail)
    For IA-NT STD up to 1.3 For IA-NT STD For IA-NT PWR
    IA-NT-STD_HW1.3-2.5.0.3.AIL IA-NT-STD-2.5.0.3.AIL IA-NT-PWR-2.5.0.3.AIL

    Table 3.2 Available archives

    3.2 Overview of all available hardware


    IA-NT STD up to 1.3 IA-NT STD IA-NT PWR
    Binary Inputs 3 4 7
    Binary Outputs 4 4 7
    Analog Inputs 0 0 0
    Analog Outputs 0 0 0
    RS232, RS485, USB,
    Communications RS232, RS485, USB RS232, RS485, USB
    Ethernet

    Table 3.3 Available hardware

    Inteli ATS 2.5 New Features List 5


    3.3 Available related documentation
    Documents Description
    Global GuideIA-NT-STD-2.5
    IA-NT-STD-2.5-Reference Guide
    http://www.comap.cz/support/download-center/type/manuals/
    Global GuideIA-NT-PWR-2.5
    IA-NT-PWR-2.5-Reference Guide
    http://www.comap.cz/support/download-center/type/manuals/
    Global Guide of PC tool LiteEdit
    LiteEdit 5.1.0 Global Guide.pdf
    http://www.comap.cz/support/download-center/type/manuals/
    New Features List of PC tool LiteEdit
    LiteEdit 5.1.2 New Features List.pdf
    http://www.comap.cz/support/download-center/type/manuals/

    Table 3.4 Available documentation

    Inteli ATS 2.5 New Features List 6


    4 Notes
    4.1 Source evaluation
    Source evaluation is same for generator and mains. Setpoints and binary inputs connected with source
    evaluation are:
    GenProtect setpoint (for generator)
    MainsProtect setpoint (for mains)
    GenReadyToLoad binary input (for generator)
    MainsHealthy binary input (for mains)
    State of source can be evaluated in these ways:
    Binary input only
    Measured values only
    Binary input and measured values

    4.1.1 Binary input only


    In this case the binary input GenReadyToLoad or MainsHealthy has to be configured. After configuration of
    binary input, related setpoint GenProtect or MainsProtect should be adjust to DISABLED. After that the source
    will be evaluated only from binary inputs.

    4.1.2 Measured values only


    In this case the binary input GenReadyToLoad or MainsHealthy can’t be configured. Related setpoint
    GenProtect or MainsProtect is adjust to value ENABLED and its value can’t be changed. Source is evaluated
    only from measured values (voltage and frequency).

    4.1.3 Binary input and measured values


    In this case the binary input GenReadyToLoad or MainsHealthy has to be configured. After configuration of
    binary input, related setpoint GenProtect or MainsProtect should be adjust to ENABLED. After that the source
    will be evaluated from both sources. To evaluate that source is health the values of voltage and frequency have
    to be in limits and also related binary input has to be in logical one.

    4.2 Document history


    Revision number Related sw. version Date Author
    1 2.5 8.2.2016 Michal Slavata

    Inteli ATS 2.5 New Features List 7

    You might also like