Scribd
Upload
63 views3 pages

Design of Beams at 419.10m LVL: General Data

This document summarizes the design of two beams, BR1 and BR2, at a height of 419.10m. It provides the general data used in the design including concrete strength, steel grade, clear cover, member widths and depths. It then shows the design calculations for bending moment, shear and reinforcement details for both positive and negative moments for each beam. Reinforcement amounts, bar diameters and spacings are specified to satisfy design code requirements.

Uploaded by

ankkeshmundra1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
63 views3 pages

Design of Beams at 419.10m LVL: General Data

This document summarizes the design of two beams, BR1 and BR2, at a height of 419.10m. It provides the general data used in the design including concrete strength, steel grade, clear cover, member widths and depths. It then shows the design calculations for bending moment, shear and reinforcement details for both positive and negative moments for each beam. Reinforcement amounts, bar diameters and spacings are specified to satisfy design code requirements.

Uploaded by

ankkeshmundra1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Design of Beams at 419.

10m LVL

General Data
Concrete G Fck N/mm2 = 25
Steel Grade Fy N/mm2 = 415
Clear cove Cv mm 25

BR1 BR2
Member No STAAD Pro 11 1647
Load Case No. 307 106
Width of 380 mm 200 200
Depth D mm = 500 500
Effective D d mm = 467 465

Design Calculation - (Using STAAD Pro Analysis Results )


( - ve ) Moment
Mu (-ve) At Face kNm = 111 124
Mu/bd^2 = 2.54 2.87
SP-16 Table 3
% of steel required 0.82 0.94
Ast (-ve) 0.053 mm2 = 762.144 0.055 876.06
Reinforcement provided
Dia of bar Φ mm = 16 16
No of bar N = 4 3
+ +
Dia of bar Φ mm = 0 12
No of bar N = 0 3
At continu Astxs mm2 = 804 942

( + ve ) Moment
Mu (-ve) kNm = 111 113
Mu/bd^2 = 2.54 2.61
SP-16 Table RECHECK
% of steel required 0.82 0.84
Ast (-ve) mm2 = 762.144 783.06
Reinforcement provided
Dia of bar Φ mm = 16 16
No of bar N = 5 4
+ +
Dia of bar Φ mm = 0 0
No of bar N = 0 0
At continu Astxs mm2 = 1005 804

check for shear


Shear at su Vus kN = 135 113
Nominal sh tv N/mm2 = 1.45 1.22
Ast provided mm2 = 804 942
%of steel pt % = 0.86 1.01
BSS = 3.37 2.87
Permissible tc = 0.61 0.42
Balance she Vus kN = 78.39 73.94
SP-16 Tabl Vus / d = 1.68 1.59
Dia of strriups mm = 8 8
Spacing of strriups re mm = 216 228
Spacing of strriups p mm = 200 150

You might also like