Scribd
Upload
1K views2 pages

Lab 12 - Total Internal Reflection

This lab investigates the phenomenon of total internal reflection that occurs when light travels from an optically dense medium to a less dense one. When the angle of incidence exceeds the critical angle, the light is totally internally reflected rather than refracted. Students use an acrylic block and ray table to observe total internal reflection and calculate the critical angle. They then measure the angle of incidence for total internal reflection to determine the index of refraction of the acrylic, finding a result that differs from the accepted value by around 88%.

Uploaded by

api-408463795
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views2 pages

Lab 12 - Total Internal Reflection

This lab investigates the phenomenon of total internal reflection that occurs when light travels from an optically dense medium to a less dense one. When the angle of incidence exceeds the critical angle, the light is totally internally reflected rather than refracted. Students use an acrylic block and ray table to observe total internal reflection and calculate the critical angle. They then measure the angle of incidence for total internal reflection to determine the index of refraction of the acrylic, finding a result that differs from the accepted value by around 88%.

Uploaded by

api-408463795
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Name: Ivan wilberg

LAB 12. RAY OPTICS: TOTAL INTERNAL REFLECTION


AP PHYSICS II

Driving Question | Objective


We have seen what happens when light goes from low index (fast) to high
index (low), but what happens when light goes from high index to low
index? What is the maximum refractive angle you can get?
Investigate what happens as light tries to go from slow to fast.

Materials and Equipment


 Light Source  Acrylic Block
 Protractor  Acrylic Semicircle
 Ray Table  Ruler

Procedure
1. Place the acrylic Semicircle on the ray table in the
outline provided on the ray table.

2. Place the light source on the table in ray-box mode and


aim a ray to the curved side of the acrylic semicircle as
seen in the image to the right. Assure that the incident
ray is aimed perpendicular to the surface and directly
toward the center of the ray table as seen.

3. Begin rotating the ray table and observe what happens


to the refracted light that leaves the flat side of the acrylic semicircle. Describe what you see below.

It’s getting dimmer and dimmer And eventually dies at 90°

4. The incident angle in which this happens is the angle that results in a refracted angle of 90°. Using Snell’s Law,
we get: 𝒏𝟏 𝐬𝐢𝐧 𝜽𝟏 = 𝒏𝟐 𝐬𝐢𝐧 𝜽𝟐 → 𝒏𝒂𝒄𝒓𝒚𝒍𝒊𝒄 𝐬𝐢𝐧 𝜽𝒄𝒓𝒊𝒕𝒊𝒄𝒂𝒍 = 𝒏𝒂𝒊𝒓 𝐬𝐢𝐧 𝟗𝟎°.

5. Solve for 𝜃𝑐𝑟𝑖𝑡𝑖𝑐𝑎𝑙 in terms of the other variables:


1
𝜽𝒄𝒓𝒊𝒕𝒊𝒄𝒂𝒍 =1/sin−1
𝑛𝑎𝑐𝑟𝑦𝑙𝑖𝑐

6. This is known as the critical angle. Note that any


angle of incidence greater than this does not result
in any refraction at all, but rather a reflection. This
is called total internal reflection and is widely
used in modern appliances such as fiber optics to
transmit signals via pulses of light through cables
over long distances. Even if the cable bends!
Activity
Now that we know about total internal reflection, lets attempt to determine the index of refraction of our acrylic
block using a critical angle.

1. Place the light source in ray-box mode on the lab table.

2. Position the trapezoid in the box below as shown in the figure. Trace the
perimeter of the block.

3. Shine a ray into the side of the block and move the position of the light source
until you just reach the point where you achieve total internal reflection.

4. Mark the exact points where light enters, reflects, and exits the block.

5. Remove the block, connect a ray from Entrance to Reflection points as well as a
ray from Reflection point to Exit Point.

6. Measure the angle between the two rays inside the block with the protractor. This is 2𝜃𝑐 .

a. What is 𝜃𝑐 ? 𝜽𝒄 = 48.5°

7. Using the equation that you determined on the front of this page for 𝜃𝑐 , calculate the index of refraction of this
acrylic block.

8. 𝑛𝑎𝑐𝑟𝑦𝑙𝑖𝑐 = 0.846The accepted value for the index of refraction of acrylic is 𝑛 = 1.5. What was your % difference?

Attach a picture of your ray tracing below.

Calculate your % error

𝑒𝑥𝑝𝑒𝑟𝑖𝑚𝑒𝑛𝑡𝑎𝑙−𝑎𝑐𝑡𝑢𝑎𝑙
% difference = 100 × | | = 𝟖𝟕. 𝟓%
𝑎𝑐𝑡𝑢𝑎𝑙

Save this file as a PDF (NOT WORD!) document for submission.

You might also like