Communication Cable and Adapter

7XV5 and more

(Cable, Adapter, Converter, Special cable e.g.)

Application / Pin assignment

04/2009
 Caution !

This brochure also contains descriptions of products that have been

discontinued, or are only to be used for testing purposes or as commissioning
aids, and are not distributed by Siemens AG.

There will be no liability or guarantees for damages of any kind,

caused by the reproduction or re-fitting of the described products.

Our products are mainly custom made and are intended especially for
professional application and testing in substations.
Special attention is paid to safety against accidental contact and error free data
transmission, also in EMC burdened environment.

Current information regarding our products may be found in the Internet under:

www.siprotec.com

16.04.2009 Manual Communication Cable and Adapter Page 2 of 27

Index

GENERAL INSTRUCTIONS....................................................................................................................5
1 COMMUNICATION CABLE FOR THE OPERATION OF PROTECTION DEVICES WITH PC.....6
1.1 7XV5100 Serial RS232-communication cable (wire / FO) ................................................6
1.1.1 7XV5100-0/BB PC/PG 25-pole to the protection device 25-pole ......................................6
1.1.2 7XV5100-1 PG 750 to protection device 25-pole ..............................................................6
1.1.3 7XV5100-2 PC / PG to protection device 25-pole ............................................................6
1.1.4 7XV5100-3 PG 750 (COM2) to Plotter 1604.....................................................................7
1.1.5 7XV5100-4 (/BB) PC/PG 9-pole to protection device 9-pole (DIGSI-cable) .....................7
1.1.5.1 7XV5100-4 (/BB) Additional applications ...........................................................................8
1.1.5.2 7XV5100-8H 9/25-pol. Adapter for cable 7XV5100-4........................................................8
1.1.6 7XV5100-4A PC/PG 9-pole to the local interface of the channel switch 7XV5500 ..........8
1.1.7 7XV5100-5 PC / PG 25-pol. to protection device 9-pole ..................................................9
1.1.8 7XV5100-6 Serial RS232 cable with galvanic separation via FO cable ............................9
2 RS485-BUS SYSTEM FOR DIGSI- / IEC- / VDEW-COMMUNICATION ......................................10
2.1 RS485-Bus with 9-pole Sub-D plug...................................................................................10
2.1.1 7XV5103-0AAxx Y-Bus cable for RS485-Bus with 9-pole plug .......................................10
2.1.2 7XV5103-1AAxx Extension bus cable for RS485-Bus with 9-pole plug ..........................11
2.1.3 7XV5103-2AA00 adapter cable for devices with RS485-bus on terminals .....................11
2.1.4 7XV5103-7AAxx RS485 adapter cable from the RTD-Box to SIPROTEC 4 ...................11
2.2 RS485-Bus system with RJ45-plug...................................................................................12
2.2.1 7XV5103-2BA00 Adapter cable for devices with RS485-Bus on 9-pol. Sub-D plug .......13
2.2.2 7XV5103-2CA00 Adapter cable for devices with RS485-Bus on 8-pol. RJ45 plug.........13
2.2.3 7XV5103-5BA00 RS485-Terminator with RJ45 plug.......................................................13
2.2.4 7KE6000-8GDxx Ethernet patch cable CAT5 with RJ45 plugs .......................................13
3 BUS CABLE FOR TIME SYNCHRONISATION OF SIPROTEC PROTECTION DEVICES ........14
3.1 7XV5104 Bus cable for synchronization for standard time only ...................................14
3.1.1 7XV5104-0AAxx Y-Bus cable for standard time only ......................................................14
3.1.2 XV5104-1AA10 Extension cable for standard time only ..................................................15
3.1.3 7XV5104-2AA00 Adapter cable with open ends for standard time only..........................15
3.1.4 7XV5104-3AA00 T-Adapter cable (2 Busses) for standard time only .............................15
3.2 7XV5105 Bus cable for synchronization for standard time and second puls ..............15
3.2.1 7XV5105-0AAxx Y-Bus cable for standard time and second puls...................................16
3.2.2 7XV5105-1AA10 Extension cable for standard time and second puls ............................16
3.2.3 7XV5105-2AA00 Adapter cable with open ends for standard time and second puls ......16
4 CABLE FOR CONVERTER 7XV5700 (RS232 - RS485)..............................................................17
4.1 7XV5700 RS232-interface to the PC ..................................................................................17
4.1.1 7XV5100-2 RS232-cable from 7XV5700 to PC ...............................................................17
4.2 7XV5700 RS485-Bus-Interface...........................................................................................17
4.2.1 7XV5100-7/BB RS485-cable from 7XV5700 to the first protection device with terminals17
4.2.2 7XV5100-7B RS485-cable from 7XV5700 to protection device with 9-pole RS485 plug.18
5 7XV5710 CONVERTER CABLE USB 2.0 TO RS485 WITH SUB-D PLUG................................18

16.04.2009 Manual Communication Cable and Adapter Page 3 of 27

6 CABLE FOR REMOTE OPERATION OF THE PROTECTION DEVICES VIA MODEM .............19
6.1 Cable from PC to "Office modem" ....................................................................................19
6.1.1 Office modem cable from PC 9-pol. to modem 25-pol.....................................................19
6.1.2 Office modem cable from PC 9-pol. to modem 9-pol.......................................................19
6.2 Cable from "Substation modem" to converters or Prot. devices ..................................20
6.2.1 7XV5810-0AA10 Substation modem 25-pol. to Prot. device with 9-pol. interface ..........20
6.2.1.1 7XV5810-0AA10 Additional Application...........................................................................20
6.2.2 7XV5820-0AA10 Substation modem 9-pol. to Prot. device with 9-pol. interface ............20
6.2.2.1 7XV5820-0AA10 Additional Application...........................................................................21
6.2.3 Substation modem 25-pol. to Prot. device with 25-pol. front interface ............................21
6.2.4 Substation modem 25-pol. to I/O on Channel switch 7XV5500.......................................21
7 RS232 - FO CONVERTER WITH ACCESSORIES.......................................................................22
7.1 7XV5101 RS232 - FO Converter.........................................................................................22
7.1.1 7XV5101-0A For Prot. device with 25pol. interface ........................................................22
7.1.2 7XV5101-0B For modem with 25pol. interface ...............................................................22
7.1.3 7XV5101-1A For Channel switch (I/O-interface) ............................................................23
7.1.4 7XV5101-1B For PC (Desktop) with 25pol. interface .....................................................23
7.1.5 7XV5101-3A For Channel switch (Prot. device interface) ..............................................23
7.1.6 7XV5101-3C For Notebook with 9pol. interface .............................................................23
7.2 Designs and Pin Configurations .......................................................................................24
7.2.1 Tabular representation .....................................................................................................24
7.2.2 Graphical Outline .............................................................................................................25
7.2.3 Switching DTE / DCE in the 7XV5101-0x and -1x ...........................................................25
7.3 Ordering data (MLFB) .........................................................................................................25
7.4 Elbow plug for 25-pol. front interface on prot. device V3...............................................26
7.4.1 7XV5101-8A (angled towards long edge of relay connector) ..........................................26
7.4.2 7XV5101-8B (angled towards short edge of relay connector).........................................26

16.04.2009 Manual Communication Cable and Adapter Page 4 of 27

General Instructions
The description of the accessories in this manual includes the information required for the
normal use of the products described therein. It is intended for technically qualified
personnel that has been specially trained or has special knowledge in the fields of
protection-, instrumentation-, control-, and automatic control engineering (called
automation in the following). The knowledge and the technically correct implementation
of the safety instructions and warnings included in this manual are a prerequisite for the
safe installation and commissioning, as well as for safety during operation and
maintenance, of the product described. Only qualified personnel, as defined earlier, has
the necessary expertise for the specific implementation in all eventualities, of the safety
instructions and warnings in a generally accepted manner.
This manual is not an integral part of the scope of delivery. For reasons of transparency
it does not contain all details with respect to all configurations of the described products
and can also not cover every conceivable implementation with regard to operation or
maintenance. If further information is desired or in case special problems should arise,
which are not treated adequately in this document, it is possible to obtain additional
details from the local Siemens office or from the addresses stated in the back of this
manual.

Additionally, we point out that the content of this product documentation is not part of or
modifies any previous or existing agreement, promise, or legal relationship.
All obligations by Siemens result from the respective purchase order which also includes
the complete and exclusively valid warranty provision. The contractual warranty
regulations are neither extended nor limited by the statements in this document

Liability Statement
We have compared the text of this manual with the hardware and software described.
Omissions and deviations cannot be ruled out; we accept no liability for lack of total
conformity.
The information in this manual is checked periodically, and necessary corrections will
be included in future editions. We appreciate any suggested improvements.
We reserve the right to make technical improvements without notice. Any suggestions
for improvements are welcome.

Note !
This brochure also contains descriptions of products that have been discontinued, or
are only to be used for testing purposes or as commissioning aids, and are not
distributed by Siemens AG.

There will be no liability or guarantees for damages of any kind, caused by the
reproduction or re-fitting of the described products,

Copyright

Copyright © Siemens AG 2009. All rights reserved.

Dissemination or reproduction of this document, or evaluation and communication of its
contents, is not authorized except where expressly permitted. Violations are liable for
damages. All rights reserved, particularly for the purposes of patent application or trademark
registration

16.04.2009 Manual Communication Cable and Adapter Page 5 of 27

1 Communication cable for the operation of protection devices with PC

1.1 7XV5100 Serial RS232-communication cable (wire / FO)

1.1.1 7XV5100-0/BB PC/PG 25-pole to the protection device 25-pole

The serial patch cable establishes the connection of a serial 25-pole interface (e.g. COM 1)
or PG 685-interface to a protection device with a 25-pole service interface.

PC / PG 685 7XV5100-0/BB Prot. device

25pol. female Length 3m 25pol. male
2 TxD 2
3 RxD 3
7 GND 7
1
4
5
6
20

1.1.2 7XV5100-1 PG 750 to protection device 25-pole

The serial patch cable establishes the connection of the serial 25-pole PG-750 interface with
a socket plug and a protection device with a 25-pole service interface.

PG 750 7XV5100-1 Prot. device

25pol. male Length 3m 25pol. male
2 TxD 2
3 RxD 3
7 GND 7
1
4
5
6
20

1.1.3 7XV5100-2 PC / PG to protection device 25-pole

The serial patch cable establishes the connection of the serial 9-pole PC interface with male
plug (e.g. COM 1) or PG-interface with a protection device with 25-pole service interface.

Notebook / PC 7XV5100-2 Prot. device

9pol. female Length 3m 25pol. male
2 RxD 3
3 TxD 2
5 GND 7
4
6
7
8

16.04.2009 Manual Communication Cable and Adapter Page 6 of 27

1.1.4 7XV5100-3 PG 750 (COM2) to Plotter 1604
The serial patch cable establishes the connection of the serial 9-pole PG 750-interface
COM2 to a plotter 1604 with HP-Emulation by means of a 25-pole socket plug.

Plotter 1604 with

PG750 COM2 7XV5100-3
HP-Emulation
9pol. female Length 3m 25pol. male
2 RxD 2
3 TxD 3
5 GND 7
6 20
8
Housing

1.1.5 7XV5100-4 (/BB) PC/PG 9-pole to protection device 9-pole

(DIGSI-cable)
The serial patch cable (DIGSI-cable) establishes the connection of the serial 9-pole PC
interface with male plug (e.g. COM1) or PG interface to a protection device with 9-pole
service interface. The following devices have such an interface: 7SJ531, 7SJ602 and all
SIPROTEC 4 devices, e.g. 7SA522, 7SA6x, 7SJ61/62/63, 6MD6x, etc.

Notebook / PC 7XV5100-4 Prot. device

9pol female. Length 3m 9pol. male
2 RxD 3
3 TxD 2
5 GND 5
4 7*
6 8*
7
* for Starcoupler
8

In the case of cable 7XV5100-0 Version /BB the shielding was changed. The cable shield is
no longer connected with “GND”, but has plug housings at both ends.

Notebook / PC 7XV5100-4 /BB Prot. device

9pol. female Length 3m 9pol. male
2 RxD 3
3 TxD 2
5 GND 5
4
6
7 7*
8 8*
Shield
Housing Housing

* for Starcoupler

16.04.2009 Manual Communication Cable and Adapter Page 7 of 27

1.1.5.1 7XV5100-4 (/BB) Additional applications
The following devices have the same allocation as the protection devices with 9-pole
interfaces and can also be connected to a PC or notebook with this cable.
(Mini-) Star coupler 7XV5300, 7XV5450
Active Mini-Star coupler 7XV5550
RS232-FO Converter 7XV5652

With this cable and the 9/25-pole adapter 7XV5100-8H, protection devices with 25-pole
interfaces can also be connected.

1.1.5.2 7XV5100-8H 9/25-pol. Adapter for cable 7XV5100-4

P ro t. d e v ic e
7 X V 5 1 0 0 - 4 (/B B ) 7 X V 5 1 0 0 -8 H 2 5 p o l. m a le
9 p o l. fe m a le P lu g h o u s in g
2 R xD 2
3 TxD 3
5 GND 7

If this 9/25-pole adapter is connected with the 9-pole male plug of the cable 7XV5100-4
(/BB), protection devices with a 25-pole service interface can also be connected to the PC or
notebook with this cable.

1.1.6 7XV5100-4A PC/PG 9-pole to the local interface of the channel

switch 7XV5500
The serial patch cable establishes the connection between the PC and the local interface of
the channel switch 7XV5500.

Channel switch
Notebook / PC 7XV5100-4A Local interface
9pol. female Length 3m 9pol. male
1 1
2 RxD 2
3 TxD 3
4 4
5 GND 5
6 6
7 7
8 8

16.04.2009 Manual Communication Cable and Adapter Page 8 of 27

1.1.7 7XV5100-5 PC / PG 25-pol. to protection device 9-pole
The serial patch cable establishes the connection of the serial 25-pole PC interface with
male plug (e.g. COM 1) with a protection device having a 9-pole service interface. The
following devices have such an interface: 7SJ531, 7SJ602 and all SIPROTEC 4 devices, e.g.
7SA522, 7SA6x, 7SJ61/62/63, 6MD6x, etc.

PC 7XV5100-5 Prot. device

25pol. female Length 3m 9pol. male
2 TxD 2
3 RxD 3
7 GND 5
1 7*
4 8*
5
* for Starcoupler
6
20

1.1.8 7XV5100-6 Serial RS232 cable with galvanic separation

via FO cable
These cables connect the PC to the protection device, with galvanic separation, and as a
result extremely secure against interference, via FO cable. The conversion of RS232-level to
light takes place in so-called "self-supplying devices" without additional power supply, by
utilisation of the signalling voltage from the data signals. To do this, the interface of the
connected device (including a note-book running on batteries) must supply at least +/- 5V-
signals. Baud rates of up to 115kB are then possible.
7XV5100-6B PC 9-pole for protection 25-pole (2m)
7XV5100-6C PC 9 pole for protection 25-pole (5m)
7XV5100-6F PC 9-pole for protection 25-pole (3m)
7XV5100-6D PC 9-pole for protection/star-coupler 9-pole (2m)
7XV5100-6E PC 9-pole for protection/star-coupler 9-pole (5m)
Notebook / PC 7XV5100-6B/C/F Prot. device
9-pol. female 25-pol. male
2 RxD FO 3
3 TxD 2
5 GND 7
4
6
7
8
Prot. device/
Notebook / PC Starcoupler
9-pol. female
7XV5100-6D/E 9-pol. male
2 RxD 3
FO
3 TxD 2
5 GND 5
4 7*
6 8*
7 * for Starcoupler
8

16.04.2009 Manual Communication Cable and Adapter Page 9 of 27

 2 RS485-Bus system for DIGSI- / IEC- / VDEW-communication

2.1 RS485-Bus with 9-pole Sub-D plug

The bus system with 9-pole sub-D plugs has been used in systems with SIPROTEC 4
protection devices, the converters 7XV5 and Siemens control devices for a considerable
period of time. The connection of individual devices is done directly via special Y-cables, or
via the corresponding adapter cables to devices with different connection technologies.
The bus is terminated with a 9-pole sub-D bus termination plug with integrated 220 OHM
resistance.
These cables are not suitable for PROFIBUS.

Note: The baud rate and the data format of all devices connected to the bus must be
set the same. The devices addresses (1-254) must differ.

7SA6x 7SA522 7RW600

7SJ61 7SD522 7SJ602 7SD600
7SJ62/63 7SJ600

SIEMENS SIEMENS
SIEMENS SIPROTEC SIEMENS SIPROTEC
RUN RUN
RUN ERROR RUN ERROR
ERROR ERROR
Anr. L1
L1 402,1A Max450.1A Anr. L2 L1 402,1A Max450.1A
L2 402,1A Max450.1A Anr. L3 L2 402,1A Max450.1A
L3 402,1A Max450.1A Anr. Erde L3 402,1A Max450.1A
Anr. L1 Anr. L1
E 00.0A Automat E 00.0A Anr. L2 Anr. L2

Anr. L1 Aus L1
Anr. L2 Aus L2
Anr. L3 Aus L3
Anr. Er de Aus Erde
Automat

Adapter cable
7XV5103-2AA00

S2 S2 B1
C C

S2
B A B A

S2
RS485 S1 B3 S1 B3 S1 B3 S1 B3 ST
Master
Y-Bus cable RS485 Y-Bus cable RS485 Y-Bus cable RS485 Y-Bus cable RS485 RS485-Terminator
7XV5103-0AAxx 7XV5103-0AAxx 7XV5103-0AAxx 7XV5103-0AAxx 7XV5103-5AA00

2.1.1 7XV5103-0AAxx Y-Bus cable for RS485-Bus with 9-pole plug

7XV5103-0AAxx
RS485 Y-Bus cable
Prot. device
9pol. male
Housing 3 8
--> Master Slave -->
9pol. male Length 1 / 3 / 5 / 10 m 0,2 m 9pol. female
3 A 3
3+8 twisted pair
8 B 8
Housing Shield Housing

16.04.2009 Manual Communication Cable and Adapter Page 10 of 27

2.1.2 7XV5103-1AAxx Extension bus cable for RS485-Bus
with 9-pole plug

7XV5103-1AAxx
RS485 Extension cable
--> Master Slave -->
9pol. male Length 10 / 20 / 30 / 40 / 50 m 9pol. female
3 A 3
3+8 twisted pair
8 B 8
Housing Shield Housing

2.1.3 7XV5103-2AA00 adapter cable for devices with RS485-bus

on terminals
This adapter cable enables the connection of devices which have a RS485 interface on
terminals, e.g. 7SJ600, 7SD600, 7RW600, 7SS600 and SIPROTEC 4 surface mounting
devices, to the RS485-bus.

7XV5103-2AA00 RS485-Adapter cable

Prot. device e.g. 7SJ600 to SIPROTEC-devices with terminal RS485-Bus
2x wire end SUB-D
ferrule Length 10 cm Length 20 cm 9-pol. male
A (3) 3
Terminal 29
3+8 twisted pair
B (8) 8
Terminal 28
Length 15 cm Shield Housing
Housing
Ring cable lug
for screw typ M4

2.1.4 7XV5103-7AAxx RS485 adapter cable from the

RTD-Box to SIPROTEC 4
This adapter cable allows for the connection of an RTD-Box via the open cable ends directly
to a SIPROTEC device with a 9-pole sub D plug. Using the connections A’ and B’ the
application of the termination resistances or the connection of a second RTD-Box is possible.
The termination resistance is integrated in the sub-D plug to the SIPROTEC device.

RTD-Box
7XV5662-xAD10 SIPROTEC 4 Device
4x wire end ferrule SUB-D
Terminator 120 Ohm
A' 9pol. male
A = Pin 3 Length 5 / 25 / 50 m 3
A
B = Pin 8 3+8 twisted pair 8
B
Shield Housing
B'

16.04.2009 Manual Communication Cable and Adapter Page 11 of 27

2.2 RS485-Bus system with RJ45-plug

In the case of the serial bus system with RJ45 sockets on the device, the bus connection is
established with cost-effective, double-screened CAT 5 patch cables. This technology is
used in the case of redundant IEC 60870-5-103 system interfaces on the device. The
connection of the individual devices to the two redundant busses is in each case done via
two special Y adapter cables. The busses each terminate at a RJ45 bus termination plug
with integrated 120 Ohm resistance.
For the connection of SIPROTEC-devices with 9-pole sub-D plugs, or for connection to the
bus system with 9-pole sub-D plugs, a special adapter is available (see catalog sheet).
These cables are not suitable for PROFIBUS.

Note: The baud rate and the data format of all devices connected to the bus must be set the
same. The device addresses (1-254) must be different.

7SA522
7SJ6x 7SJ6x 7SJ6x 7SD522
7SJ62/63

SIEMENS SIPROTEC SIEMENS SIPROTEC SIEMENS SIPROTEC SIEMENS SIPROTEC

RUN ERROR RUN ERROR RUN ERROR RUN ERROR
Anr . L1
L1 402,1A Max450.1A L1 402,1A Max450.1A L1 402,1A Max450.1A Anr . L2 L1 402,1A Max450.1A
L2 402,1A Max450.1A L2 402,1A Max450.1A L2 402,1A Max450.1A Anr . L3 L2 402,1A Max450.1A
L3 402,1A Max450.1A L3 402,1A Max450.1A L3 402,1A Max450.1A Anr . Er de L3 402,1A Max450.1A
E 00.0A E 00.0A E 00.0A Automat E 00.0A

Anr . L1 Anr. L1 Anr . L1 Aus L1

Anr . L2 Anr. L2 Anr . L2 Aus L2
Anr . L3 Anr. L3 Anr . L3 Aus L3
Anr . Er de Anr. Er de Anr . Er de Aus Erde
Automat Automat Automat

2x RS485 (RJ45) 2x RS485 (RJ45) 2x RS485 (RJ45) RS485 (Sub_D)

redundant redundant not redundant

Master Master
RTU 1 RTU 2

C C C C

B A B A B A B A

Patch cable Patch cable Patch cable Patch cable RS485-Terminator

7XV5103-5BA00
Patch cable Patch cable Y-Adapter Y-Adapter
RJ45 to 2x RJ45 Sub-D to 2x RJ45
2x Y-Adapter 2x Y-Adapter 2x Y-Adapter 7XV5103-2CA00 7XV5103-2BA00
Sub-D to 2x RJ45 RJ45 to 2x RJ45 RJ45 to 2x RJ45 RS485-Terminator
7XV5103-2BA00 7XV5103-2CA00 7XV5103-2CA00 7XV5103-5BA00 -- All Patch cable 7KE6000-8GD0x-xAAx --

16.04.2009 Manual Communication Cable and Adapter Page 12 of 27

2.2.1 7XV5103-2BA00 Adapter cable for devices with RS485-Bus
on 9-pol. Sub-D plug

To RS485-Bus Y-Adapter cable 7XV5103-2BA00

Patch cable
For connect SIPROTEC 4 or 7XV5 devices with Sub-D interface plug
on a RS485-Bus with patch cables
1* Length 0,3 m To SIPROTEC 4
B*
RS485 with Sub-D
2*
A*
1 8
B B
2 3+8 twisted pair 3
A A
Housing Shield Housing

Housing with two Sub-D plug

RJ45 plugs 8-pol. female 9-pol. male

2.2.2 7XV5103-2CA00 Adapter cable for devices with RS485-Bus

on 8-pol. RJ45 plug

To RS485-Bus
Patch cable Y-Adapter cable 7XV5103-2CA00
1* For connect SIPROTEC 4 devices with RJ45 interface plug
B* on an RS485-Bus with patch cables
2* Length 0,3 m
A*
4*
X* To SIPROTEC 4
RS485 with RJ45
5*
Y*
1 A/A* and B/B* for RS485 data 1
B B
2 1+2 twisted pair 2
A A
4 4
X X
5 4+5 twisted pair 5
Y Y
Housing Shield Housing

Housing with two RJ45 plug

RJ45 plugs 8-pol. female 8-pol. female

2.2.3 7XV5103-5BA00 RS485-Terminator with RJ45 plug

Termination resistance, 120 Ohm integrated in 8-pole RJ45 plug for one-sided termination of
a RS485-Bus.

Terminator plug 7XV5103-5BA00

1
B
R=120 Ohm
P= 0,25W
2
A

RJ45-Stecker
8-pol. Stift

2.2.4 7KE6000-8GDxx Ethernet patch cable CAT5 with RJ45 plugs

Only double-screened CAT 5 patch cables, SFTP 1:1 connection (e.g. 7KE6000) may be
used as bus cables. The maximum bus length may not exceed 800m.

16.04.2009 Manual Communication Cable and Adapter Page 13 of 27

3 Bus cable for time synchronisation of SIPROTEC protection devices

3.1 7XV5104 Bus cable for synchronization

for standard time only
These “bus cables” are intended for the distribution of IRIG-B signals (GPS), DCF77 signals
or minute impulses to port A of SIPROTEC devices. The 2-core cables 7XV5104 transmit
only the normal time, the 4-core cables 7XV5105 additionally transmit the highly accurate
second impulse for differential protection devices. The source of the signals is the GPS-
receiver 7XV5664 and the Sync-transceiver 7XV5654 with 24 V voltage level. The entire bus
length should not exceed 20m (do not use a termination resistance).

Confectioned Timesync bus cable for SIPROTEC 4 time synchronization

SIEMENS SIPROTEC SIEMENS SIPROTEC SIEMENS SIPROTEC

RUN ERROR RUN ERROR RUN ERROR
Anr. L1 Anr. L1
Anr. L2 L1 402,1A Max450.1A L1 402,1A Max450.1A Anr. L2 L1 402,1A Max450.1A
Anr. L3 L2 402,1A Max450.1A L2 402,1A Max450.1A Anr. L3 L2 402,1A Max450.1A
Anr. Erde L3 402,1A Max450.1A L3 402,1A Max450.1A Anr. Erde L3 402,1A Max450.1A
Automat E 00.0A E 00.0A Automat E 00.0A

Aus L1 Anr. L1 Aus L1

Aus L2 Anr. L2 Aus L2
Aus L3 Anr. L3 Aus L3
Aus Erde Anr. Erde Aus Erde
Automat

GPS-receiver 7XV5664 with

Wide range power supply 7XV5810
and Sync-transceiver 7XV5654

X1 X2

+Vin -Vin
+O C3 -OC3
+O C2 -OC2
RUN

R1 R2 1 2 1 2
0V 24V/ 6W +O C1 -OC1
BI 2
K2
7XV5810-0BA00 CLK DEF
C1-C 3
Weitbereichsnetzteil Sync-Transceiver
SERIES: A4-K7-655430 7XV5654-0BA00/BB
CE 5
RCV 1
RCV 2

UH 24-250V DC F.-Nr.: BF123456789 !

RUN

60-230V AC IRIG B / III I IIII IIII IIII III III III UH 24 -25 0V D C / 6W
DCF77-In 10 0-2 30 V AC / 15 VA
CE 5 FL1 50 / 6 0 Hz

UH UH
2 1 N /L - L1 /L+ 2 1 N /L - L1 /L+
GPS-In
FL1

T-Adapter
C S2 S3 7XV5104-3AA00 C S2 C S2

B A B A B A

Y-Bus cable Y-Bus cable Y-Bus cable

B3 7XV5104-0AAxx S1 B5 B4 S1 7XV5104-0AAxx B3 S1 7XV5104-0AAxx B3

3.1.1 7XV5104-0AAxx Y-Bus cable for standard time only

The SIPROTEC devices are connected directly via their TimeSynch interface to the bus with
a 2-core Y-bus cable.
7XV5104-0AAxx Y-Bus cable
Length 1/3/5/10 m (for standard time only)
Plug Sub-D
1 3 9pol. male
Plug Sub-D
Housing Plug Sub-D
9pol. male
9pol. female
1 24 V (Time) 1

3 GND (Time) 1+3 twisted pair 3

Housing Shield Housing

16.04.2009 Manual Communication Cable and Adapter Page 14 of 27

3.1.2 XV5104-1AA10 Extension cable for standard time only
The 2-core extension cable extends the bus by 10m (without second pulse).
The total length of the bus should not exceed 20 m

7XV5104-1AA10 Extension cable

Plug Sub-D Length 10 m (for standard time only)
Plug Sub-D
9pol. male
9pol. female
1 24 V (Time) 1

3 GND (Time) 1+3 twisted pair 3

Housing Shield Housing

3.1.3 7XV5104-2AA00 Adapter cable with open ends

for standard time only
The 2-core adapter cable with open ends facilitates the connection of the bus to the GPS-
receiver with connection terminals (without second pulse).

7XV5104-2AA00 Adapter cable

open ends with Length 0,3 m (for standard time only) Plug Sub-D
2x wire end ferrule 9pol. female
1 24 V (Time) 1

3 GND (Time) 1+3 twisted pair 3

Housing Shield Housing

Ring cable lug

for screw typ M4

3.1.4 7XV5104-3AA00 T-Adapter cable (2 Busses)

for standard time only
With this T-adapter cable, both channels of the Synch-transceiver 7XV5654 can be used
(without second pulse).

7XV5104-3AA00 Adapter cable

Length 2 x 0,3 m (for standard time only)

Plug Sub-D
1 3 8 4 9pol. male
Plug Sub-D Plug Sub-D
9pol. female 9pol. female
1 24 V (Time) 24 V (Time) 1

3 GND (Time) 1+3 twisted pair 1+3 twisted pair GND (Time) 3

Housing Shield Shield Housing

3.2 7XV5105 Bus cable for synchronization

for standard time and second puls
7XV5105 is a 4-core screened bus system for synchronization of the normal time with
second impulse at Port A (24V connection) in SIPROTEC-protection devices. The additional
highly accurate second impulse is exclusively required for the synchronisation of two line
differential protection devices via GPS. The entire bus length should not exceed 20m (do not
use a termination resistance).

16.04.2009 Manual Communication Cable and Adapter Page 15 of 27

3.2.1 7XV5105-0AAxx Y-Bus cable for standard time
and second puls
Using a 4-core Y bus cable, the SIPROTEC-devices are directly connected to the bus via
their Time Sync interface. The IRIG-B telegrams for normal time and the second impulse are
transmitted in parallel.

7XV5105-1AA10 Y-Bus cable

Length 1/3/5/10 m for standard time and second puls
Plug Sub-D
Plug Sub-D Housing 1 3 8 4 9pol. male Plug Sub-D
9pol. male 9pol. female
8 24 V (Puls) 8

4 GND (Puls) 4+8 twisted pair 4

1 24 V (Time) 1

3 GND (Time) 1+3 twisted pair 3

Housing Housing

3.2.2 7XV5105-1AA10 Extension cable for standard time

and second puls
The 4-core adapter cable extends the bus by 10m. The total length of the bus should not
exceed 20m.

7XV5105-1AA10 Extension cable

Plug Sub-D Length 10 m for standard time and second puls Plug SUB-D
9pol. male 9pol. female
8 24 V (Puls) 8

4 GND (Puls) 4+8 twisted pair 4

1 24 V (Time) 1

3 GND (Time) 1+3 twisted pair 3

Housing Housing

3.2.3 7XV5105-2AA00 Adapter cable with open ends for standard time
and second puls
The 4-core adapter cable with open ends enables the connection of the bus to radio
controlled clocks with connection terminals.
7XV5105-2AA00 Adapter cable
open ends with Length 0,3 m for standard time and second puls Plug Sub-D
2x wire end ferrule 9pol. female
8 24 V (Puls) 8

4 GND (Puls) 4+8 twisted pair 4

1 24 V (Time) 1

3 GND (Time) 1+3 twisted pair 3

Shield Housing

16.04.2009 Manual Communication Cable and Adapter Page 16 of 27

4 Cable for converter 7XV5700 (RS232 - RS485)

4.1 7XV5700 RS232-interface to the PC

NOTE! Depending on the order number 7XV5700-xx the cable 7XV5100-2 and the RS232-
interface adapter may or may not be contained in the scope of delivery.

4.1.1 7XV5100-2 RS232-cable from 7XV5700 to PC

The socket plug of the 25-pole RS232-interface of the converter 7XV5700 may be attached
directly to the serial 25-pole interface of the PC. If the PC only has a 9-pole interface, the
conversion is done via a standard adapter from the Sub-D 9-pole plug socket to the 25 pole
male plug or the DIGSI cable 7XV5100-2. The adapter and the DIGSI cable swap the
connections of the pins 2 and 3.

Notebook / PC 7XV5100-2 Prot. device

9-pol. female Length 3m 25pol. male
2 RxD 3
3 TxD 2
5 GND 7
4
6
7
8

4.2 7XV5700 RS485-Bus-Interface

Note! The cables 7XV5100-7 /BB or 7XV5100-7B to the RS485-interface are, depending on
the order number 7XV5700-xx, included in the scope of delivery.

4.2.1 7XV5100-7/BB RS485-cable from 7XV5700 to the first protection

device with terminals
The cable connects the RS485-converter to the first protection device with RS485-interface
on terminals with ring lugs, e.g. 7SJ600, 7SD600, 7RW600 etc. If further devices (maximally
31) are to be connected, the RS485 bus can be extended.

To 7XV5700-x Device with Terminals

RS485 converter Cable 7XV5100-7/BB
25pol. male (RS485) Length 1m Ring cable lug
B
10 Terminal 28
11
19
A
21 Terminal 29
22
23 GND
Housing Terminal 27
13 Shield
25

16.04.2009 Manual Communication Cable and Adapter Page 17 of 27

4.2.2 7XV5100-7B RS485-cable from 7XV5700 to
protection device with 9-pole RS485 plug.
The cable connects the RS485-converter 7XV5700 with one protection device with 9-pole
RS485-interface, e.g. 7SA522, 7SA6x, 7SJ602, 7SJ61/62/63, 7SD522, 6MD6x etc.

If further devices (maximally 31) are to be connected, the RS485-Bus can be extended with
the Y bus cables 7XV5103-0AAxx and a standard 9-pole "Gender Changer" (socket, socket)
(also see 7XV5103-xx).
To 7XV5700 Prot. device
RS 485-Interface 7XV5100-7B
25pol. male Length 1m 9-pol. male
B
10 8
11
19 A
21 3
22
23
GND
Housing 5
13
25

NOTE! The mode of operation in the RS485-converter is set with the jumpers in the 25-pole
plug of the cables 7XV5100-7.

5 7XV5710 Converter cable USB 2.0 to RS485 with Sub-D plug

The USB - RS485 converter cable with it’s specific pin allocation enables a temporary
connection of up to 31 Siemens protection devices with electric RS485 interface to a PC with
USB interface, for direct or central operation with DIGSI 4.

Converter cable 7XV5710-0AA00

Converter cable USB 2.0 (1.1) to RS485
100k

390

Length 1,8 m
3
A 10
Plug USB
Plug Sub-D
220

USB-A S1
9-pol. male
B 8
B 10
100k

390

TTL 5
A

16.04.2009 Manual Communication Cable and Adapter Page 18 of 27

6 Cable for remote operation of the protection devices via modem

6.1 Cable from PC to "Office modem"

The standard modem cables connect the office modem with the PC or notebook. These
cables are not contained in the scope of delivery of each order, are however available as a
standard article by mail order or from specialised dealers.

6.1.1 Office modem cable from PC 9-pol. to modem 25-pol.

Notebook / PC Modem
9-pol. female Max. length 3m 25-pol. male

1 DCD 8
2 RxD 3
3 TxD 2
4 DTR 20
5 GND 7
6 DSR 6
7 RTS 4
8 CTS 5
9 RI 22
Housing Housing

6.1.2 Office modem cable from PC 9-pol. to modem 9-pol.

Notebook / PC Modem
9-pol. female Max. length 3m 9-pol. male
1 < DCD 1
2 < RxD 2
3 TxD > 3
4 DTR > 4
5 GND 5
6 < DSR 6
7 RTS > 7
8 < CTS 8
9 < RI 9
Housing Housing

16.04.2009 Manual Communication Cable and Adapter Page 19 of 27

6.2 Cable from "Substation modem" to converters or Prot. devices
A direct connection from the modem to the protection devices is generally not advisable, as
induced over-voltages (e.g. lighting strike or inadequate earthing conditions) may destroy
non-isolated interfaces of the protection devices.

Note: A galvanic separation between modem and protection device via RS232-FO
converter e.g. 7XV5101 or 7XV5652-0BA00 is strongly recommended.

6.2.1 7XV5810-0AA10 Substation modem 25-pol. to

Prot. device with 9-pol. interface
Starcoupler/
Modem Prot. device
25-pol. male Max. length 3m 9pol. male
2 TxD 3
3 RxD 2
7 GND 5
Housing Housing
4 7*
5 8*
6
20 * for Starcoupler

6.2.1.1 7XV5810-0AA10 Additional Application

The following devices have the same pin allocation as the protection devices with 9-pole
interface and can also be connected to a modem with a 9-pole interface with this cable.

(Mini-) Star coupler 7XV5300, 7XV5450

Active Mini-Star coupler 7XV5550
RS232-FO Converter 7XV5652

With this cable and the 9/25-pole adapter 7XV5100-8H, protection devices with 25-pole
interface can also be connected.

6.2.2 7XV5820-0AA10 Substation modem 9-pol. to

Prot. device with 9-pol. interface
Starcoupler/
Modem Prot. device
9pol. male Length 2m 9pol. male
2 RxD 2
3 TxD 3
5 GND 5
Housing Housing
7 7*
* for Starcoupler
8 8*
6 6
4 4

16.04.2009 Manual Communication Cable and Adapter Page 20 of 27

6.2.2.1 7XV5820-0AA10 Additional Application
The following devices have the same pin allocation as the protection devices with 9-pole
interface and can also be connected to a modem with a 9-pole interface with this cable.

(Mini-) Star coupler 7XV5300, 7XV5450

Active Mini-Star coupler 7XV5550
RS232-FO Converter 7XV5652

With this cable and the 9/25-pole adapter 7XV5100-8H, protection devices with 25-pole
interface can also be connected.

6.2.3 Substation modem 25-pol. to Prot. device with 25-pol. front interface

Modem Prot. device

25pol. male Max. length 3m 25-pol. male
2 TxD 3
3 RxD 2
7 GND 5
Housing Housing
4
5
6
20

6.2.4 Substation modem 25-pol. to I/O on Channel switch 7XV5500

The 25-pole modem interface of the channel switch can be directly connected to the modem,
if all protection devices are connected via FO-converter.
Channel switch
Modem (l/O interface)
25-pol. male Max. length 3m 25-pol. female
2 TxD 2
3 RxD 3
7 GND 7
8 DCD 8
4 4
5 Pin 8 activates the I/O interface 5
6 of the channel switch, only when 6
20 a modem connection is active. 20
Housing

16.04.2009 Manual Communication Cable and Adapter Page 21 of 27

7 RS232 - FO Converter with accessories
The RS232 – FO plug modules enable the optical connection of protection devices with
electrical (also non-isolated) RS232 interface to e.g. a star coupler for central operation.
Further devices such as a PC, notebook, modem, or channel switch can be protected from
electro-magnetic interference in this way. A suitable plug module is available for each of the
listed applications.

The RS232 – FO plug modules are supplied in Sub-D plug housings and may be plugged
directly onto the interface of the corresponding devices. If the plug modules are applied
correctly, no additional settings need to be made.

The quiescent state of the optical interface is generally light OFF. Data transmission takes
place full-duplex and is transparent up to 115 kBaud. The optical interface with FSMA plug
operates at 850nm and has a typical reach of 1500m with 62,5µm fibre optic cable.

The various versions have the following differences: number of pins (9 or 25-pole), the plug
design (male or socket) and the auxiliary voltage supply (pin 9 or power supply plug). More
information regarding application and type can be found in the following individual
descriptions, the technical data and the order information.

7.1 7XV5101 RS232 - FO Converter

7.1.1 7XV5101-0A For Prot. device with 25pol. interface

The RS232 - FO Converter 7XV5101-0A may be directly plugged onto the 25-pole front
interface of the numerical protection devices. The RS232 signals are transparently converted
into light signals. The control wires are bypassed and are not supported.
The module is supplied via the protection device interface (Pin 9) and accordingly does not
require additional power supply. After opening the housing, the plug allocation DCE/DTE
may be converted for other applications. The default setting is DCE and quiescent state light
“OFF”. The quiescent state of the light cannot be changed.

7.1.2 7XV5101-0B For modem with 25pol. interface

The RS232 - FO plug module 7XV5101-0B may be directly plugged onto the 25-pole modem
interface. The RS232 signals are transparently converted into light signals. The control wires
are bypassed and are not supported.
The module is supplied via a binder socket by an external power supply (not included in the
scope of delivery). The plug allocation DCE/DTE may be converted for applications after
opening of the housing. The default setting is DCE and the quiescent state light OFF. The
quiescent state of the light cannot be changed.

A standard mouse adapter (9-pole male to 25-pole socket) can be used between the modem
and the plug module in the case of a modem with a 9-pole connection.

16.04.2009 Manual Communication Cable and Adapter Page 22 of 27

7.1.3 7XV5101-1A For Channel switch (I/O-interface)
The RS232 – FO plug module 7XV5101-1A may be plugged directly onto the rear 25-pole
I/O-interface of the active channel switch 7XV55. Die RS232 signals are transparently
converted into light signals. Die control wires are bypassed and are not supported.
The module is supplied via the I/O interface (Pin 9), and accordingly requires no additional
power supply. The plug allocation DCE/DTE may be converted for applications after opening
of the housing. The default setting is DTE and quiescent state light OFF. The quiescent state
of the light cannot be changed.

7.1.4 7XV5101-1B For PC (Desktop) with 25pol. interface

The RS232 - FO plug module 7XV5101-1B may be directly plugged onto the 25-pole PC
interface. The RS232 signals are transparently converted into light signals. The control wires
are bypassed and are not supported.

The module obtains its power (5V) from an external power supply via a binding socket
(contained in the scope of delivery).
The plug allocation DCE/DTE may be converted for applications after opening of the
housing. The default setting is DTE and quiescent state light OFF. The quiescent state of the
light cannot be changed.

For a notebook with a 9-pole connection, a standard mouse adapter (9-pole male to 25-pole
socket) can be used between modem and plug module.

7.1.5 7XV5101-3A For Channel switch (Prot. device interface)

The RS232 - FO plug module 7XV5101-3A may directly be plugged into one of the up to 32
rear 9-pole interfaces of the active channel switch 7XV5500. The RS232 signals are
transparently converted into light signals. The control wires are bypassed and are not
supported.

The module obtains its power via the interface of the active channel switch (Pin 9), and
accordingly does not require additional power supply. The default setting is DTE and
quiescent state light OFF. The quiescent state of the light cannot be changed.

7.1.6 7XV5101-3C For Notebook with 9pol. interface

The RS232 – FO plug module 7XV5101-3C may be directly plugged onto the 9-pole serial
interface of the notebook.

The RS232 signals are transparently converted into light signals. The control wires are
bypassed and are not supported.

The module obtains its power via a cable from the keyboard DIN interface or the mouse DIN
interface of the notebook.
The default setting is DTE and quiescent state light OFF. The quiescent state of the light
cannot be changed.

16.04.2009 Manual Communication Cable and Adapter Page 23 of 27

7.2 Designs and Pin Configurations

7.2.1 Tabular representation

7XV5101- 0A 0B 1A 1B 3A 3C
Housing: Plastics , metal-plated X X X X X X
Dimensions 58 x 53 x 17 X X X X
Dimensions 72 x 32 x 17 X X
Power supply +5V via pin 9 X 1) X 1) X
+5V via female connector 2) X 2) X
Plug-in PSU 220V/50Hz (included in delivery) X X
via keyboard connector of the notebook X
Electrical V.24 / RS232 DCE (steady light OFF) X X
interfaces
V.24 / RS232 DTE (steady light OFF) X X X
DTE / DCE switchable X X X X
Assignment: 2 TxD, 3 RxD, 5 GND X
Assignment: 3 TxD, 2 RxD, 5 GND
Assignment: 2 TxD, 3 RxD, 7 GND X X
Assignment: 2 RxD, 3 TxD, 7 GND X X
Assignment: 9 +5V X X X X X
Bridge contact: 4-5, 6-8-20 (25-pin) X X X X
Bridge contact: 7-8, 1-4-6 (9-pin) X X
Optical Plug-in connection FSMA black = transmit X X X X
interfaces blue = receive
Plug-in connection FSMA T = transmit X X
R = receive
Optical Power 27µW (-5,7dBm)* X X X X X X
Sensitivity 1µW (-30dBm)* X X X X X X
Optical Budget 7dB (+3dB Res.)* X X X X X X
Wavelength 850nm X X X X X X
Transmission Distance 1500m / 62,5µm X X X X X X
800m / 50µm
* Valid for 62,5µm glass fibre cable
1) Only for 7XV5101-xB (not for 7XV5101-xB /B)
2) Pin 9 may not be allocated

16.04.2009 Manual Communication Cable and Adapter Page 24 of 27

7.2.2 Graphical Outline

1m

Power Supply

Fibre optic connector

black blue
Binder- transmit receive
connector
transmit receive

2
1

T R
1 = +5V
2 = Gnd

7XV5101-0A
7XV5101-3A

SUB-D Connector 25pol.

SUB-D Connector 9pol.

7.2.3 Switching DTE / DCE in the 7XV5101-0x and -1x

SUB-D
1F
7XV5101-1A and -1B
F4 F2 F3 F5
DTE
2 = TxD, 3 = RxD
51
CS422

C5 7XV5101-0A and -0B

2u2
DCE
2 = RxD, 3 = TxD
C9
100n MAX232

7.3 Ordering data (MLFB)

Description
RS232 - LWL plug modules 7XV5101 -
for Protection device 25-pol. male UH +5V on Pin 9 0 A
for Modem 25-pol. male UH 220V AC 0 B
for 7XV5500 I/O 25-pol. female UH +5V on Pin 9 1 A
for PC 25-pol. female UH 220V AC 1 B
for 7XV5500 to Prot. device 9-pol. female UH +5V on Pin 9 3 A
for Notebook 9-pol. female UH +5V (DIN-plug) 3 C

16.04.2009 Manual Communication Cable and Adapter Page 25 of 27

7.4 Elbow plug for 25-pol. front interface on prot. device V3
If FO plug converters 7XV5101-0A are to be plugged onto the front interface under the cover
of the protection devices, the elbow plug 7XV5101-8x must be used. Two outlets have to be
applied at a suitable place on the front frame for the FO cables. As the protection devices V3
have differing interfaces, the elbow plugs are available in two variants.

7.4.1 7XV5101-8A (angled towards long edge of relay connector)

Front plate of protection relay:

7SA500 1)
7SA501 1)
7SJ511
7SJ512
Elbow plug 7XV5101-8A
7SD502
angled to long edge
7SD503
of the front connector
7SV51
7VK51

7XV5101-0A

1) Connector on the left; fibre-optic outlet down to the right.

7.4.2 7XV5101-8B (angled towards short edge of relay connector)

Front plate of protection relay:

7SA511
7SA513 1)
7SD511
7SD512
7UM516
7UT51 Elbow plug 7XV5101-8B
7SJ52 2) angled to short edge of the
7SK52 2) front connenctor
7UM511
7UM512
7SD510
7XV5101-0A

1) Connector on the left; fibre-optic outlet down to the right.

2) Connector on the right; fibre-optic outlet on the left passing through the cover.

16.04.2009 Manual Communication Cable and Adapter Page 26 of 27

Suggestions and questions regarding this product are to be
addressed to:

Siemens AG
Sector:
Energy Sector
Energy Automation

P.O. Box 4806

D-90026 Nürnberg

In the case of general problems please contact our Hotline:

Tel.: +49 (0)180 524 7000

E-Mail: [email protected]

Current information regarding our products may also be found

in the Internet under: www.siprotec.com

Printed in Germany

16.04.2009 Manual Communication Cable and Adapter Page 27 of 27