HOLLOW AMERICAN NATIONAL STANDARD

METAL ANSI/
MANUAL NAAMM HMMA 861 –14
08 11 13 Hollow Metal Doors and Frames

GUIDE SPECIFICATIONS
FOR COMMERICAL
HOLLOW METAL
DOORS AND FRAMES
SEVENTH EDITION
September 15, 2014
 This standard was developed by representative members of and
approved by the Hollow Metal Manufacturers Association Division
(HMMA) of the National Association of Architectural Metal Manufactur-
ers (NAAMM) to provide their opinion and guidance on the specification
and use of swinging sound control hollow metal doors and frames. This
standard contains advisory information only and is published as a public
service by NAAMM and its HMMA Division.

NAAMM AND ITS HMMA DIVISION DISCLAIM ALL LIABILITY OF ANY

KIND FOR THE USE, APPLICATION OR ADAPTATION OF MATERIAL
PUBLISHED IN THIS STANDARD.

Current information on all NAAMM Standards is available by calling, writ-

ing, or visiting the website of the National Association of Architectural Met-
al Manufacturers, www.naamm.org.

National Association of Architectural Metal Manufacturers

800 Roosevelt Road, Building C, Suite 312
Glen Ellyn, IL 60137
Tel: 1-630-942-6591 · Fax: 1-630-790-3095
www.naamm.org

Copyright © 1974, 1976, 1987, 1993, 2000, 2006, 2014

All Rights Reserved

COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES i
 FOREWORD
These specifications have been prepared in accordance with the CSI recommended Master Format 2012 with
Part 1 - General, Part 2 - Product and Part 3 - Execution. Guide specifications are intended to be used as the
basis for developing project specifications and must be edited to fit specific project requirements. Inapplicable
provisions should be deleted, appropriate selections should be made where there are choices, and provisions
applicable to the project should be added where necessary. Options are shown in brackets. Notes, recom-
mendations and instructions to Specifiers are given in italics at the start of or directly following the sections to
which they apply. Notes that contain permissive language are not considered part of the standard. ASTM and
other standards shall be deemed as that in affect on publication date of this Guide, unless specifically noted
otherwise. When a more recent standard is available, the Specifier should verify its applicability to this Guide
prior to its inclusion. While the CSI Section Format locates Delivery, Storage and Handling in Part 1, NAAMM
standards include them under Part 3 – Execution.

Materials and fabrication methods are specified in detail in Part 2. Doors and frames manufactured in accor-
dance with these specifications have successfully met the testing and performance requirements of Section
1.05. However, the materials and fabrication methods called for in these specifications, while providing an
excellent guide, are not intended to restrict the use of other materials and methods where it can be demon-
strated through the specific testing procedures in Section 1.05 that the construction can equal or exceed the
performance levels specified. In order to ensure that a manufacturer’s product meets the desired performance
levels, the construction specifications must always include the Testing and Performance requirements of Sec-
tion 1.05 and the Quality Assurance requirements of Section 1.06.

The values stated in inch-pound units are to be regarded as the standard. Corresponding metric values are
included in parenthesis for reference purposes only.

This guide specification addresses the requirements for commercial steel stiffened hollow metal doors and
frame products.

For hollow metal doors and frames subject to less rigorous use than commercial and institutional applications,
give consideration to ANSI/NAAMM HMMA 860, “Guide Specifications for Hollow Metal Doors and Frames”,
or ANSI/NAAMM HMMA 867, “Guide Specifications for Commercial Laminated Core Hollow Metal Doors and
Frames”. If security is a factor, there are two hollow metal standards available - ANSI/NAAMM HMMA 862,
“Guide Specifications for Commercial Security Hollow Metal Doors and Frames”, and ANSI/NAAMM HMMA
863, “Guide Specifications for Detention Security Hollow Metal Doors and Frames”. For acoustic applications
consideration may be given to ANSI/NAAMM HMMA 865, “Guide Specifications for Sound Control Hollow Met-
al Doors and Frame Assemblies”. For situations where corrosion resistance beyond that of typical commercial
steel door and frame applications, or where specialized aesthetic appearance, are significant design criteria,
consideration should be given to ANSI/NAAMM HMMA 866, “Guide Specifications for Stainless Steel Hollow
Metal Doors and Frames”.

ii COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 CSI SECTION 08 11 13
HOLLOW METAL DOORS AND FRAMES
PART 1 - GENERAL
1.01 SUMMARY
This Section includes commercial hollow metal products, including doors, panels, frames, transom frames,
sidelight and window assemblies as shown in the contract documents.
1.02 PRODUCTS PROVIDED UNDER THIS SECTION
A. Commercial hollow metal doors, swinging type, including [glass moldings and stops] [louvers] [louver
inserts] [other] as shown in the approved submittal drawings.
B. Commercial hollow metal panels, fixed or removable, flush or rabbeted, similar in construction to
hollow metal doors.
C. Commercial hollow metal frames, transom frames, sidelight and window assemblies, including [glass
moldings and stops] [louvers] [louver inserts] [hollow metal panels] [in-fill panels] [other] as shown in
the approved submittal drawings.
In this guide specification the term “frame product” is used to define, as, a group; frames, tran-
som frames, sidelights,and window assemblies.
1.03 RELATED SECTIONS
A. Section 01 66 00 - Product Storage and Handling
B. Section 03 30 00 – Cast in Place Concrete
C. Section 04 20 00 – Unit Masonry
D. Section 05 10 00 - Structural Metal Framing (for Lintels, Posts, Columns or Other Load Bearing Ele-
ments)
E. Section 06 11 00 - Wood Framing
F. Section 08 11 19 - Stainless Steel Doors and Frames
G. Section 08 34 53 - Security Doors and Frames
H. Section 08 34 73 - Sound Control Doors and Frames
I. Section 08 71 00 - Door Hardware (including Weather Stripping and Seals)
J. Section 08 80 00 - Glazing
K. Section 09 20 00 – Plaster and Gypsum Board (for the Installation of Commercial Hollow Metal
Doors and Frames in Steel Stud Partitions).
L. Section 09 90 00 - Painting and Coating
M. Section 11 19 00 - Detention Equipment
N. Section __ __ __ - Field Measurements
This specification covers only those products listed in Section 1.02. Not included in Section
08 11 13 are builders or rough hardware of any kind, weather-stripping, gasketing, items fur-
nished by others, field painting, and protection at the building site of products furnished under
this Section.

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 1

 1.04 REFERENCES
The Standards listed in this Guide are referenced by basic designation only. The edition of
a Standard is deemed as that in affect on the publication date this Guide, unless specifically
noted otherwise. If a more recent standard is available, the Specifier should verify its applica-
bility to this Guide prior to its inclusion.
A. ANSI/SDI A250.4, Test Procedure and Acceptance Criteria for Physical Endurance for Steel Doors,
Frames and Hardware Reinforcings
B. ANSI/SDI A250.10, Standard Test Procedure and Acceptance Criteria for Prime Painted Steel Sur-
faces for Steel Doors and Frames
C. ANSI/NAAMM HMMA 801, Glossary of Terms for Hollow Metal Doors and Frames
D. ANSI/NAAMM HMMA 841, Tolerances and Clearences for Commercial Hollow Metal Doors and
Frames
E. ANSI/NAAMM HMMA 866, Guide Specifications for Stainless Steel Hollow Metal Doors and Frames
F. ANSI/NFPA 80 , Standard for Fire Doors and Other Opening Protectives
G. ANSI/NFPA 105, Standard for the Installation of Smoke Door Assemblies and Other Opening Pro-
tectives.
H. ANSI/NFPA 252, Standard Methods of Fire Tests of Door Assemblies
I. ANSI/NFPA 257, Standard Fire Test for Windows and Glass Block Assemblies
J. ANSI/UL 9, Fire Test of Window Assemblies
K. ANSI/UL 10C, Positive Pressure Fire Tests of Door Assemblies
L. ANSI/UL 1784, Air Leakage Test of Door Assemblies
M. ASTM A 653/A 653M, Specification for Steel Sheet, Zinc Coated (Galvanized) or Zinc-Iron Al-
loy-Coated (Galvannealed) by the Hot-Dip Process
N. ASTM A 1008/A 1008M, Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High
Strength Low-Alloy and High Strength Low-Alloy with Improved Formability, Solution Hardened, and
Bake Hardenable
O. ASTM A 1011/A 1011M, Specification for Steel, Sheet, and Strip, Hot-Rolled, Carbon, Structural,
High Strength Low-Alloy and High Strength Low-Alloy with Improved Formability and Ultra High
Strength
P. ASTM C 143/A 143M, Test Method for Slump of Hydraulic-Cement Concrete
Q. CAN/ULC-S104, Standard Method for Fire Test of Door Assemblies
R. CAN4-S106, Standard Method for Fire Test of Window and Glass Block Assemblies
S. NAAMM HMMA 802, Manufacturing of Hollow Metal Doors and Frames
T. NAAMM HMMA 803, Steel Tables
U. NAAMM HMMA 805, Recommended Selection and Usage Guide
V. NAAMM HMMA 810, Hollow Metal Doors
W. NAAMM HMMA 810 TN01, Defining Undercuts of Doors
X. NAAMM HMMA 820, Hollow Metal Frames
Y. NAAMM HMMA 820 TN01, Grouting Hollow Metal Frames
Z. NAAMM HMMA 820 TN02, Continuously Welded Frames
AA. NAAMM HMMA 830, Hardware Selection for Hollow Metal Doors and Frames
AB. NAAMM HMMA 831, Recommended Hardware Locations for Hollow Metal Doors and Frames
AC. NAAMM HMMA 840, Guide Specifications for Installation and Storage of Hollow Metal Doors and
Frames
AD. NAAMM HMMA 840 TN01, Painting Hollow Metal Products

2 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 AE. NAAMM HMMA 850, Fire-Rated and Smoke Control Hollow Metal Door and Frame Products
The following standards are used only for neutral pressure fire test methods and should be de-
leted from project specifications when ‘positive pressure’ is required by the governing building
code: CAN/ULC-S104 (1.04.R) and CAN4-S106 (1.04.S)
Conversely, ANSI/UL 10C (1.04.L) is used only for positive pressure fire tests and should be
deleted from project specifications requiring neutral pressure fire tests.
ANSI/NFPA 252 (1.04.H), ANSI/NFPA 257 (1.04.I) and ANSI/UL 9 (1.04.J) reference both neu-
tral pressure and ‘positive pressure’ fire test methods, and as such should be included in all
project specifications, except those requiring compliance with Canadian Building Codes.
ANSI/UL 1784 (1.04.M) is used for US smoke control assembly testing and therefore should
not be included in specifications requiring compliance with the Canadian Building Code.
Only project specifications requiring compliance with Canadian Building Codes should include
CAN/ULC-S104 (1.04.R) and CAN4-S106 (1.04.S)
Refer to Appendix 4 for a list of the Standards Writing or Accreditation Organizations refer-
enced in Section 1.04.
1.05 TESTING AND PERFORMANCE
A. Physical Endurance for Steel Doors and Hardware Reinforcings
1. Test a 3 ft. x 7 ft. (914 mm x 2134 mm), 1.75 in. (44 mm) thick nominal size door representative of
the construction and material to be provided.
2. Test in accordance with ANSI/SDI A250.4, Cycle and Twist Test procedure.
a. Cycle Test Acceptance Criteria:
i. Doors specified with 0.053 in. (1.3 mm) and thicker face sheets tested to 4,000,000
cycles.
ii. Doors specified with 0.042 in. (1.0 mm) minimum thick face sheets tested to Level A
(1,000,000 cycles ).
b. Twist Test Acceptance Criteria: Maximum deflection under 300 pound (136.1 kg) load.
i. 4,000,000 cycle-tested doors not to exceed 0.625 in. (15.8 mm) deflection and maxi-
mum permanent deflection not to exceed 0.062 in. (1.5 mm).
ii. 1,000,000 cycle-tested doors not to exceed 1.25 in. (31.7 mm) deflection and maxi-
mum permanent deflection not to exceed 0.125 in. (3.1 mm).
3. Provide Verification of Compliance from an Independent 3rd party which include a description of
the test specimen, procedures used in testing, and indicate compliance with the acceptance crite-
ria of the standard.
B. Labeled Fire-Rated and/or Smoke Control Door and Frame Product
1. Where determined and scheduled by the Architect;
a. Provide Listed or Classified doors, panels, frames, transom frames, sidelight, borrowed
light and window assemblies bearing the label of a testing agency having a factory inspec-
tion service for openings requiring fire protection and/or smoke control ratings.
b. Test doors, panels, frames, transom frames and sidelight assemblies in accordance with
[ANSI/NFPA 252] [CAN/ULC-S104] [ANSI/UL 10C] [and/or] [ANSI/UL 1784].
c. Test borrowed light and window assemblies in accordance with [ANSI/UL9 or ANSI/NFPA
257] [CAN4-S106].
ANSI/UL 10C provides for positive pressure testing to accommodate the requirements of
IBC jurisdictions and should be included only for such.
CAN/ULC-S104 and CAN4-S106 provide for ‘neutral pressure’ testing to accommodate
the requirements of the Canadian Building Code jurisdictions and should be included only
for such.

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 3

 ANSI/NFPA 252, ANSI/NFPA 257 and ANSI/UL 9 cover both neutral and positive pressure
testing and therefore should be included in all project specifications, except when compli-
ance with Canadian Building Codes is required.
ANSI/UL 1784 provides for smoke control assembly testing required by the IBC and ANSI/
NPFA 105 to accommodate these specific requirements and should be included only when
required.
Include CAN/ULC-S104 and CAN4-S106 only for projects requiring conformance with Ca-
nadian Building Codes.
2. For any door or frame product specified by the Architect to be fire-rated, which cannot qualify for
labeling due to design, hardware or other reason, advise the Architect, in the submittal documents.
Advise the Architect when hardware, glazing or other options specified, unknown at the time of
submittal document preparation, affect fire labeling eligibility.
The Specifier must ensure that all performance based criteria such as fire-protection rat-
ing, temperature-rise rating, smoke control for each opening are clearly detailed by the
Architect on the project door schedules.
For additional information, refer to NAAMM HMMA 850, “Fire-Rated and Smoke Control
Hollow Metal Door and Frame Products”.
C. Prime Paint Performance
1. Sheet steel specimens, with the product manufacturer’s production primer, replicating finish ‘as
shipped’, tested in accordance with ANSI/SDI A250.10
2. Provide Verification of Compliance from an Independent 3rd party which include a description of
the test specimen, procedures used in testing, and indicate compliance with the acceptance crite-
ria of the standard.
1.06 QUALITY ASSURANCE
A. Manufacturer’s Qualifications
1. Provide evidence of having personnel and plant equipment capable of fabricating hollow metal
door and frame product of the types specified.
2. Provide evidence of having a written quality control system in place.
B. Quality Criteria
1. Compliance with Section 1.05 is required for all door and frame product provided under this Sec-
tion.
2. Fabricate in accordance with the approved submittal drawings.
3. Meet fabrication methods and product quality standards set by the Hollow Metal Manufacturers
Association, HMMA, a division of the National Association of Architectural Metal Manufacturers,
NAAMM, as set forth in the contract documents and NAAMM’s HMMA 800 through 850 Series
documents.
1.07 SUBMITTALS
A. Submittal Drawings
1. Show dimensioned door and frame product elevations and sections.
2. Show listing of opening descriptions including locations, material thicknesses, and anchors.
3. Show location and details of openings.
4. Provide manufacturer’s recommended installation instructions and procedures.
B. Samples, upon request, provide the following.
1. Door: 1 ft. x 1 ft. (305 mm x 305 mm) corner section with hinge preparation showing top and in-
ternal construction.

4 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 2. Frame: 1 ft. x 1 ft. (305 mm x 305 mm) section showing assembled corner joint at head and jamb.
Include hinge reinforcement [and grout guard] in one rabbet. When glazed frame product is spec-
ified, apply and install glazing stop as specified in the opposite rabbet. Apply glazing stop to both
head and jamb section to show their intersection.
3. All samples submitted must represent in all respects the minimum quality of work to be furnished
by the manufacturer. Do not fabricate any work represented by the samples until the samples are
approved. Any deveation of fabrication quality compared to the approved samples is cause for
rejection of the work.
C. Contractor responsible for coordination and installation of products covered under this Section will;
1. Verify and provide to the manufacturer, actual opening sizes and site conditions by field mea-
surements before fabrication. Coordinate field measurements with fabrication and construction
schedules to avoid delays.
2. Verify that substrate conditions, whether existing or installed under other Sections, are as detailed
in the Architect’s drawings, and are acceptable for product installation in accordance with the man-
ufacturer’s instructions.
D. Reflect measurements and conditions determined under Section 1.07.C in submittal documents and
manufacture product accordingly.
E. Do not proceed with fabrication without receipt of approved submittal drawings and approved hard-
ware schedules.
The approved submittal drawings and the approved hardware schedule are the versions that
have been provided to the hollow metal manufacturer at the time of release for fabrication.
These drawings and the schedule are considered part of the project construction documents.
Insist upon receiving detailed templates along with approved submittal drawings to assure
proper coordination between Contractor and installers.
F. Contractor responsible for the coordination of procuring products provided under this Section and
Section 1.03 - Related Sections is hereby instructed to comply with the hollow metal manufacturer’s
ordering instructions and lead time requirements to avoid delays.
PART 2 - PRODUCTS
2.01 HOLLOW METAL DOORS
A. Materials
1. Steel
a. Cold-rolled steel conforming to ASTM A 1008/A 1008M, CS, Type B
b. Hot-rolled, pickled and oiled (HRPO) steel conforming to ASTM A 1011/A 1011M, CS,
Type B
c. Zinc-coated steel conforming to ASTM A 653/A 653M, CS, Type B
B. Construction
ANSI and ASTM Standards no longer utilize ‘gage’ to define steel thickness. In this Spec-
ification steel is expressed in terms of minimum decimal inch (millimeter) thickness. Di-
mensions or sizes traditionally expressed in fractional inches are shown in decimal inches
(millimeters). HMMA has developed a series of Tables, (NAAMM HMMA 803) included
as Appendix 1 of this Specification, to summarize the imperial standards and their corre-
sponding metric values.
1. Fabricate types, sizes, and construction, in accordance with the contract documents, and meeting
the performance requirements of Section 1.05.
2. Door face sheet thickness and steel type.
a. Interior doors constructed of 0.042 in. (1.06 mm) minimum thickness commercial quality
steel sheet, free of scale, pitting or surface defects, conforming to; ASTM A 1008/A 1008M
for cold-rolled steel; ASTM A 653/A 653M, CS, Type B, Coating Designation A25 (ZF75)
for zinc-coated steel; or ASTM A 1011/A 1011M, CS, Type B, for hot-rolled pickled and
oiled steel.

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 5

 For interior doors subject to corrosive conditions it is recommended that zinc-coated face
sheets, as specified in 2.01.B.2.b, be used.
b. Exterior doors constructed of 0.053 in. (1.3 mm) minimum thickness zinc-coated steel
conforming to ASTM A 653/A653M, CS, Type B, Coating Designation A60 (ZF180) or G60
(Z180).
If the Architect determines that zinc coated face sheets and internal components are need-
ed, 2.01.B is the appropriate location to specify this requirement.
For doors subject to severely corrosive conditions it is recommended that stainless steel
products, as detailed in NAAMM’s ANSI/NAAMM HMMA 866, “Guide Specifications for
Stainless Steel Hollow Metal Doors and Frames”, be utilized.
3. Join face sheets at their vertical edges by a continuous weld extending the full height of the door,
with no visible seams on their faces or vertical edges.
See “Welded, Continuously” in ANSI/NAAMM HMMA 801, “Glossary of Terms for Hollow Metal
Doors and Frames”
4. Fabricate doors with minimum nominal door thickness of 1.75 in. (44 mm). Fabricate doors neat
in appearance and free from warpage or buckle. Bend edges true and straight, and of minimum
radius for the thickness of metal used.
5. Prior to shipment mark each door with an identification number as shown on the approved submit-
tal drawings.
6. Stiffen doors using continuous vertically formed steel sections which, upon assembly, span the full
thickness of the interior space between door faces. Fabricate stiffeners from 0.026 in. (0.6 mm)
minimum thickness steel and space them so that the vertical interior webs are no more than 6 in.
(152 mm) apart. Securely fasten stiffeners to both face sheets by spot welds spaced a maximum
of 5 in. (127 mm) on center vertically. Fill spaces between stiffeners with fiberglass or mineral rock
wool batt-type material.
a. Where determined and scheduled by the Architect, insulate temperature rise rated (TRR)
fire doors to limit the temperature rise on the “unexposed” side of the door, as required by
the governing building code requirements.
7. Close the top and bottom edges with a continuous steel channel, not less than 0.053 in. (1.3 mm)
thickness, welded to both face sheets.
8. Close exterior doors, or doors where otherwise scheduled by the Architect, flush at the top edge.
Where required for attachment for weather-stripping, provide a flush steel closure channel at the
bottom edge. Provide openings in the bottom closure channel of exterior doors to permit the es-
cape of entrapped moisture.
9. Provide edge profiles on both vertical edges of doors as follows, unless hardware dictates other-
wise:
a. Single acting doors - beveled .125 in. (3.1 mm) in 2 in. (50.8 mm) profile
b. Double acting doors - rounded on 2.125 in. (54 mm) radius
10. Hardware Reinforcements and Preparations
a. Weld all hardware reinforcements to door.
b. Mortise, reinforce, drill and tap doors at the factory for templated hardware only, in ac-
cordance with the approved hardware schedule and templates provided by the hardware
supplier.
c. Mortise and reinforce doors for anchor hinges, thrust pivots, pivot reinforced hinges, or
non-templated hardware. Drilling and tapping, by others.
d. Reinforce doors for surface mounted hardware or continuous hinges. Drilling and tapping,
by others

6 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 e. Steel thickness for hardware reinforcements to be the manufacturer’s standard as re-
quired to adequately support the door and hardware, but not less than:
i. Full mortise hinges and pivots.....................................0.167 in. (4.24 mm) or 0.123 in.
(3.12 mm) angle or channel
shaped type
ii. Lock fronts, mortised latching devices
and strikes...................................................................0.093 in. (2.3 mm) or 0.053 in.
(1.34 mm) unitized reinforce-
ment with extruded tapped
holes that provide equivalent
number of thread as 0.093 in.
(2.3 mm)
iii. Concealed holders and surface mounted closers.......0.093 in. (2.3 mm)
iv. Internal reinforcements for other
surface mounted hardware..........................................0.067 in. (1.7 mm)
f. Where power operated hardware is indicated on the approved hardware schedule, provide
access from hinge edge to device in accordance with the templates provided.
11. Glazing Moldings and Stops
a. Where specified or scheduled, provide doors with steel moldings to secure glazing ma-
terials furnished and installed in the field by others, in accordance with glazing sizes and
thickness shown in the contract documents.
b. Provide fixed glazing molding or integral stops, 0.032 in. (0.81 mm) minimum thickness,
located on the secure side of the door, as designated on the Architect’s drawings and/or
door schedules.
c. Fabricate channel shaped removable glazing stops not less than 0.032 in. (0.8 mm) ma-
terial thickness, with tight fitting butt or mitered corners, and secure with #6 minimum,
corrosion resistant countersunk sheet metal screws.
d. Treat metal surfaces to which removable glazing stops are applied and the inside of the
removable glazing stops for maximum paint adhesion and coat with a rust inhibitive primer
prior to installation in the door. Glazing stops fabricated from zinc-coated steel conforming
to ASTM A 653/A 653M, A25 (ZF75) for interior doors, A60 (ZF180) for exterior openings
need not be primed on the inside.
e. Prepare fire-protection rated doors for listed glazing as required in accordance with the
door manufacturer’s fire rating procedure.
12. Louvers.
a. Provide doors with louvers where specified in the contract documents.
b. Louvers for non-fire-protection rated doors; welded inverted V type, Y type or Z type, face
sheet pierced construction or louver inserts.
c. Fabricate welded inverted V, Y and Z type vanes from 0.042 in. (1.06 mm) minimum thick-
ness steel, matching the Type and Finish of the door face sheets.
d. Prepare fire-rated doors for listed, fire door louvers.
e. Provide insect and/or bird screens at louvers for exterior application doors where shown
on the contract documents.
2.02 HOLLOW METAL PANELS
A. Hollow metal panels, 1.75 in. (44 mm) nominal thickness, of the same materials and construction as
specified in Section 2.01 of this specification.
B. Finish hollow metal panels as specified in Section 2.06 of this specification.

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 7

 2.03 HOLLOW METAL FRAMES
Provisions of Section 2.03 are applicable to frames, transom frames, sidelight and window
assemblies, unless indicated otherwise.
A. Materials
1. Steel
a. Cold-rolled steel conforming to ASTM A 1008/A 1008M, CS, Type B
b. Hot-rolled, pickled and oiled (HRPO) steel conforming to ASTM A 1011/A 1011M, CS,
Type B
c. Zinc-coated steel conforming to ASTM A 653/A 653M, CS, Type B
B. Construction
1. Fabricate frame product as welded units of the sizes and types shown on the approved submittal
drawings. Frame product shall be constructed in accordance with the contract documents and
meet the performance criteria specified in Section 1.05. Knocked-down frames are not acceptable.
2. Profile thickness and steel type:
a. Interior Frame Product: Construct profiles of commercial quality steel sheet, free of scale,
pitting or surface defects; cold-rolled steel conforming to ASTM A 1008/A 1008M; zinc-coat-
ed steel conforming to ASTM A 653/A 653M, CS, Type B, Coating Designation A25 (ZF75);
or hot-rolled, pickled and oiled steel conforming to ASTM A 1011/A 1011M, 0.053 in. (1.3
mm) minimum thickness. Fabricate frame product from 0.067 in. (1.7 mm) minimum thick-
ness for single door openings exceeding 4 ft. (1219 mm) in width, pairs with either door
exceeding 4 ft. (1219 mm) in width and for nominal door opening height exceeding 10 ft.
(3048 mm).
For interior areas subject to corrosive conditions it is recommended that zinc-coated frame
product, as specified in 2.03.B.2.b, be used.
b. Exterior Frame Product: Construct profiles from zinc coated steel conforming to ASTM A
653/A 653M, CS, Type B, Coating Designation A60 (ZF180) or G60 (Z180),0.053 in. (1.3
mm) minimum thickness. Fabricate frame product from 0.067 in. (1.7 mm) minimum thick-
ness for single door openings exceeding 4 ft. (1219 mm) in width, pairs with either door
exceeding 4 ft. (1219 mm) in width and for nominal door opening height exceeding 10 ft.
(3048 mm).
If the Architect determines that zinc coated frame product and internal components are
needed, 2.03.B is the appropriate location to specify this requirement.
For frame product subject to severely corrosive conditions it is recommended that stain-
less steel products, as detailed in NAAMM’s ANSI/NAAMM HMMA 866, “Guide Specifica-
tion for Stainless Steel Hollow Metal Doors and Frames”, be utilized.
3. Fabricate all finished work neat in appearance, square, and free of defects, warps and buckles.
Pressed steel members shall be straight and of uniform profile throughout their lengths.
4. Provide jamb, header, mullion and sill profiles in accordance with the frame schedule and as
shown on the approved submittal drawings.
5. Fabricate corner joints with all contact edges closed tight, with faces mitered where the two joining
memberers faces are equal , and with stops mitered or butted.
6. Welding
a. Perimeter face joints (flush or indented): Continuously welded internally or externally with
flush face joints finished smooth with seamless faces. Continuously weld internally the
rabbets and soffits.
b. Internal flush face joints: Continuously welded and finished smooth with seamless faces.
c. Members at internal indented intersections: Securely welded to concealed reinforcements,
and have hairline face seams.

8 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 d. All other intersection elements: Hairline seams.
See NAAMM HMMA 820, “Hollow Metal Frames”, and NAAMM HMMA 820-TN02-03, “Con-
tinuously Welded”, and Figure 1 of this specification, for further details on frame welding.
7. Fabricate frame product with stop heights of 0.625 in. (15.8 mm) minimum.
8. Cap cut-off stops, where specified, at heights as shown on the approved submittal drawings, weld,
fill and grind smooth so that there are no visible seams at the jamb joints below cut-off stops.
It is recommended that cut off stops not be used at exterior, lead lined, double egress or gas-
keted openings.
9. Prepare each door opening for single stud, resilient door silencers, three (3) per strike jamb for
single door openings, two (2) per head for pairs, except on gasketed or weather stripped frame
product. Silencers supplied and installed by others.
10. When shipping limitations or site access so dictate, or when advised by the contractor responsible
for coordination or installation, fabricate frame product for large openings in sections designated
for assembly in the field. Install alignment plates or angles at each joint of the same material and
thickness as the frame in accordance with aproved submittal drawings.. Assemble sections, weld
joints, grind smooth and prime paint by others under Section 06 11 00 or 09 20 00.
11. Prior to shipment mark frame product with an identification number as shown on the approved sub-
mittal drawings.
12. Hardware Reinforcements and Preparations
a. Weld all hardware reinforcements to frame product.
b. Mortise, reinforce, drill and tap frame product at the factory for templated hardware only, in
accordance with the approved hardware schedule and templates provided by the hardware
supplier.
c. Mortise and reinforce frame product for anchor hinges, thrust pivots or non-templated mor-
tised hardware. Drilling and tapping,by others.
d. Reinforce frame product for surface mounted hardware or continuous hinges. Drilling and
tapping, by others.
See NAAMM HMMA 830, “Hardware Selection for Hollow Metal Doors and Frames” for
additional information.
e. Minimum thickness of hardware reinforcements;
i. Full mortised hinges and pivots....................................0.167 in. x 1.25 in. x 10 in. length
(4.2 mm x 31.7 mm x 254 mm)
ii. Strikes..........................................................................0.093 in. (2.3 mm) or 0.053 in.
(1.3 mm) unitized reinforcement
with extruded tapped holes that
provide equivalent number of
threads as 0.093 in. (2.3 mm)
iii. Flush bolts, closers, hold open arms, and other
surface applied hardware.............................................0.093 in. (2.3 mm)
13. Where power opperated hardware is indicated on the Architect’s drawings or approved hardware
schedule, provide prepared grout guards in accordance with the templates provided. Fabricate
access plates, where required, of the same material, thickness and finish as the frame product,
fastened with corrosion resistant screws. Secure access plates with a minimum of four (4) #8-32
machine screws or #6 sheet metal screws, spaced at 12 in. (305 mm) on center maximum.
14. Floor Anchors
a. Weld floor anchors inside jambs. Provide two (2) holes for fasteners supplied and installed
by others under Section [06 10 00] [09 20 00].

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 9

 b. Where specified or scheduled, provide adjustable floor anchors with no more than 2 in.
(50.8 mm) height adjustment.
c. For applications that do not permit the use of a floor anchor, substitute an additional jamb
anchor at a location not to exceed 8 in. (204 mm) from the base of the jamb.
d. Thickness of floor anchor; same as frame, minimum..
15. Jamb Anchors
a. Provide frame product with anchorage appropriate to frame and wall construction.
b. Masonry Type:
Provide steel adjustable jamb anchors of the strap and stirrup or T-strap type not less than
0.053 in. (1.34 mm) thickness or 0.156 in. (4 mm) diameter wire type, for frame product
to be installed in new masonry walls. Straps; 2 in. x 10 in. (50 mm x 254 mm) in size
minimum, corrugated and/or perforated. Place jamb anchors at a maximum of 18 in. (457
mm) from top and bottom of openings. Minimum number of anchors, spaced at maximum
of 32 in. (813 mm) on center, provided on each jamb based on the over-all frame height.
i. Up to 60 in. (1524 mm)...................................2 anchors
ii. Greater than 60 in. (1524 mm)
up to 90 in. (2286 mm)...................................3 anchors
iii. Greater than 90 in. (2286 mm)
up to 96 in. (2438 mm)...................................4 anchors
iv. Greater than 96 in. (2438 mm).......................4 anchors plus one for each 24 in.
(610 mm) or fraction thereof, spaced
at 24 in. (610 mm) maximum between
anchors
c. Dry Wall Type
Provide steel jamb anchors of suitable design, not less that 0.042 in. (1.06 mm) thickness,
welded inside each jamb for frame product installed in drywall partitions. Place jamb
anchors at a maximum of 18 in. (457 mm) from top and bottom of openings. Minimum
number of anchors spaced at a maximum of 32 in. (813 mm) on center, provided on each
jamb, based on the over-all frame height:
i. Up to 60 in. (1524 mm)..................................3 anchors
ii. Greater than 60 in. (1524 mm)
up to 90 in. (2286 mm)...................................4 anchors
iii. Greater than 90 in. (2286 mm)
up to 96 in. (2438mm)....................................5 anchors
iv. Greater than 96 in. (2438 mm)......................5 anchors plus one for each 24 in. (610
mm) or fraction thereof, spaced at 24 in.
(610 mm) maximum between anchors
d. Expansion Bolt Type
Prepare frame product for installation in existing masonry or concrete walls for expansion
bolt type anchors. Provide a countersunk or dimpled hole for a 0.375 in. (9.5 mm) diame-
ter flat head bolt and a spacer welded within the frame profile. Locate anchors a maximum
of 6 in. (152 mm) from the top and bottom of the frame, with intermediate spacing at a
maximum of 26 in. (660 mm) on center. Bolts and shields for such anchors provided and
installed by others under Section 06 10 00.
e. Other Anchor Types
Construct and provide frame product to be installed in pre-finished concrete, masonry or
steel openings, with anchoring systems of suitable design and quantity as shown on the
approved submittal drawings. Fasteners for such anchors shall be provided and installed
by others under Section [03 30 00] [04 20 00].

10 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 A pre-finished opening may be one that is constructed as part of another assembly or sys-
tem (e.g., precast concrete panel) and which requires anchors similar in performance to
those covered by 2.03 B.15.b, and d.
16. Fabricate frame product installed in masonry walls with door openings greater than 48 in. (1219
mm) in width with a steel angle or channel stiffener factory welded into the head. Provide stiffeners
not less than 0.093 in. (2.3 mm) in thickness, not longer than the door opening width. Stiffeners and
frame product are not be used as lintels or load bearing members.
17. Attach grout guards fabricated from not less than 0.016 in. (0.4 mm) thick steel at hardware mortis-
es on frame product to be grouted.
18. For all door openings in frame product provide a temporary steel spreader welded to the base of
the jambs or mullions to serve as bracing during shipping, and handling. Spreaders are not be used
for installation.
19. In-Fill Panels
a. Where specified or scheduled, provided frame product with in-fill panels secured to frame
sections with removable steel stops.
b. For non-labeled frame product, construct in-fill panels from 0.032 in. (0.8 mm) minimum
thick steel, of the same type specified for the frame product, laminated to each face of the
manufacturer’s standard solid backing.
c. For fire-rated frame product, construct in-fill panels from 0.032 in. (0.8 mm) minimum sheet
steel, of the same type specified for the frame product, laminated to each face of a solid
approved backing.
Refer to NAAMM HMMA 850, “Fire-Rated Hollow Metal Doors and Frames”, for additional
information.
20. Removable Glazing Stops
a. Where specified, provide frame product with removable stops to secure glazing material or
in-fill panels. Glazing materials are furnished and installed in the field by others, in accor-
dance with glazing sizes and thickness shown in the contract documents.
b. Fabricate removable steel channel glazing from not less than 0.032 in. (0.8 mm) thick,
butted at corners and secured to the frame section using #6 minimum, corrosion resistant
countersunk sheet metal screws.
c. Treat the frame section underneath the glazing stops and the inside of the glazing stops
for maximum paint adhesion and coat with a rust inhibitive primer prior to installation in the
opening. Glazing stops fabricated from zinc-coated steel conforming to ASTM A 653/A
653M, A25 (ZF75) for interior frames, A60 (ZF180) or G60 (Z180) for exterior openings
need not be primed on the inside.
2.04 MANUFACTURING TOLERANCES
The manufacturer of hollow metal doors and frame product is responsible only for the manu-
facturing tolerances listed in 2.04.A. The final clearances and relationships between door and
frame depend on the setting of the frame (see Figure 4), and the hanging and adjustment of
the door and hardware. See Sections 3.02 and 3.03.
A. Maintain manufacturing tolerances within the following limits and in accordance with ANSI/NAAMM
HMMA 841:
1. Frame Product for Singles or Pairs of Doors
a. Width, measured between rabbets at the head: nominal opening width + 0.0625 in. (+ 1.5
mm), - 0.03125 in. (- 0.8 mm)
b. Height (total length of jamb rabbet): nominal opening height + 0.0625 in. (+ 1.5 mm), -
0.03125 in. (- 0.8 mm)

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 11

 c. Cross sectional profile dimensions (see Figure 2):
i. Face............................................................. ± 0.0313 in. (0.8 mm)
ii. Stop.............................................................. ± 0.0313 in. (0.8 mm)
iii. Rabbet.......................................................... ± 0.0313 in. (0.8 mm)
iv. Depth............................................................ ± 0.0625 in. (1.5 mm)
v. Throat........................................................... ± 0.0938 in (2.3 mm)
Frame product overlapping walls to have throat dimension 1/8 in. (3.1 mm) greater than
dimensioned wall thickness to accommodate irregularities in wall construction.
2. Doors
Tolerances for actual hollow metal door size are as follows:
a. Width................................................................... ± 0.0468 in. (1.2 mm)
b. Height.................................................................. ± 0.0468 in. (1.2 mm)
c. Thickness............................................................ ± 0.0625 in. (1.5 mm)
d. Perimeter Flatness.............................................. 0.0625 in. (1.5 mm) maximum
e. Surface Flatness................................................. 0.125 in (3.1 mm) maximum
f. Twist.................................................................... 0.0625 in. (1.5 mm) maximum
g. Squareness ......................................................... 0.0625 in. (1.5 mm) maximum
Surface flatness is applicable to doors up to 48” in width and 120” in height. Doors that
exceed these measurements will possible exceed this tolerance and are not considered
defective as long as they operate/function properly.
Hollow metal doors are undersized to fit the frame’s door opening. Edge clearances are
based upon individual manufacturer’s designs.
3. Hardware
a. Cutouts...............................................................Template dimensions +0.0156 in. (0.4
mm), - 0
b. Location............................................................. ± 0.0313 in. (0.8 mm)
c. Between hinge centerlines................................ ± 0.0156 in (0.4 mm)
d. Face cutout for hinges....................................... + 0.0625 in.(1.5 mm) – 0
e. Mortise depth of reinforcement.......................... ± 0.0156 in (0.4 mm)
These tolerances provide a reasonable guideline for manufacturing of hollow metal prod-
ucts. However, it should be noted that the cumulative effect of manufacturing tolerances
at or near their maximum levels could have an effect on operating clearances. Tolerance
buildup occurs when several tolerances are at or near their maximums. Care should be
taken to keep each of these tolerances as close to zero as possible.
2.05 HARDWARE LOCATIONS
A. The location of hardware on doors and frame product shall be as listed below. All dimensions, ex-
cept the hinge locations, are referenced from the floor as defined in Section 3.03.B.3.
When hollow metal frame products are specified for use with doors to be furnished by
others, hardware preparations on the doors are normally governed by the location on the
frames as stated, in 2.05 A.
1. Hinges
a. Top................................................................. 5 in. (127 mm) from underside of frame
rabbet at door opening to top of hinge
b. Bottom.......................................................... 10 in. (254 mm) from floor to bottom of
hinge

12 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 c. Intermediate.................................................. Centered between top and bottom hinges
d. On dutch doors.............................................. 5 in. (127 mm) from underside of frame
rabbet at door opening to top of upper
hinge; 10 in. (254 mm) from floor to bottom
of lower hinge; and 5 in. (127 mm) from split
line to top and bottom of lower and upper
intermediate hinges, respectively
2. Locks and latches.......................................................38 in. (965 mm) to centerline of knob or lever
shaft
3. Deadlocks...................................................................46 in. (1168 mm) to centerline of cylinder
4. Exit hardware..............................................................Centerline of cross bar as shown on hard-
ware template or as shown on approved contract documents..
5. Door pulls....................................................................42 in. (1066 mm) to center of grip
6. Push/pull bars..............................................................42 in. (1066 mm) to centerline of bar
7. Hospital latch arm pulls................................................45 in. (1143 mm) to centerline
8. Push plates..................................................................46 in. (1168 mm) to centerline of plate
9. Roller latches...............................................................46 in. (1168 mm) to centerline of latch
The hardware locations listed in this specification reflects HMMA’s 830, “Hardware Selec-
tion for Hollow Metal Doors and Frames” and 831, “Recommended Hardware Locations
for Hollow Metal Doors and Frames”. However, specific hardware and/or individual door
frame manufacturers’ designs may require different locations.
2.06 FINISH
A. After fabrication, fill and sand all tool marks and surface imperfections as required to make face
sheets, continuously welded vertical door edges and weld joints free from irregularities and dressed
smooth.
B. After appropriate metal preparation to ensure maximum paint adhesion, provide a factory applied
rust inhibitive direct to metal (DTM) primer coating to all exposed surfaces of door and frame prod-
uct manufactured from cold-rolled, hot-rolled, or G60 (Z180) zinc-coated. Meet the performance
requirements of Section 1.05.C.
C. All primer must be cured prior to shipment.
PART 3 - EXECUTION
3.01 SITE STORAGE AND PROTECTION OF MATERIALS
Correct site storage and protection are essential to proper performance of doors and
frame product. The requirements for proper storage are given in the following Section.
However, it is important to recognize that these are not the responsibility of the hollow
metal manufacturer. For this reason the requirements for storage and protection of hol-
low metal doors and frame product should be included in the Section of the specification
where installation work is specified. For additional information regarding installation see
NAAMM HMMA 840, “Guide Specification for Installation and Storage of Hollow Metal
Doors and Frames”.
A. Responsibilities of the contractor responsible for receiving hollow metal door and frame product;
1. Remove wraps or covers upon delivery at the building site and ensure that any scratches or disfig-
urement caused by shipping or handling are promptly cleaned and touched up with a rust inhibitive
‘Direct to Metal’ (DTM) primer.
2. Ensure that materials are properly stored on planks or dunnage in a dry location. Store doors and
frame product in a vertical position, spaced by blocking. Figure 3 illustrates recommended storage
positioning. Cover materials to protect them from damage but in such a manner as to permit air
circulation.

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 13

 3.02 INSTALLATION
Correct installation is essential to the proper performance of doors and frame product.
The requirements for proper installation are given in the following Sections. However it is
important to recognize that installation is not the responsibility of the hollow metal manu-
facturer. For this reason the requirements for installation should be included in Sections
03 30 00, 04 20 00, 06 11 00 and/or 09 20 00 of the project specifications, as appropriate.
For additional information see NAAMM HMMA 840, “Guide Specifications for Installation
and Storage of Hollow Metal Doors and Frames”..
A. The installer is responsible for performing the following;:
1. Prior to installation;
a. Check the area of floor on which the frame product is to be installed, and within the path
of the door swing, for flatness and correct if nessesary.
b. Check doors and frame product for correct size, swing, fire rating and opening number. If
product does not comply with contract documents, do not install and contact the supplier.
c. Isolate and protect all interior surfaces of perimeter frame product sections to be installed
in masonry or concrete walls from grout and antifreeze agents.
The drawbacks and benefits associated with the use of water based masonry grouts, with
or without antifreeze agents, should be carefully weighed during the detailing and specifi-
cation process. Grouting of mullions and other closed sections is not recommended, and
plaster based grouts should not be used. Refer to NAAMM HMMA Tech Note, HMMA 820
TN01-03, “Grouting Hollow Metal Frames”, included as Appendix 2, for further guidance.
d. Remove temporary spreaders.
e. Refinish to match original, any marks caused by spreader removal.
2. During the setting of frame product check and correct as necessary for opening width, opening
height, squareness, alignment, twist and plumbness. Maintain installation tolerances within the
following limits.
a. Opening Width.............................................. measured from rabbet to rabbet at top,
middle and bottom of frame + 0.0625 in (1.5
mm), – 0.0313 in (0.8 mm)
b. Opening Height............................................. measured vertically between the frame head
rabbet and top of floor or bottom of frame
minus jamb extension at each jamb and
across the head; + 0.0625 in (1.5 mm), –
0.0313 in (0.8 mm)
c. Squareness ................................................... measured at rabbet on a line from jamb,
perpendicular to frame head; not to exceed
0.0625 in (1.5 mm)
d. Alignment...................................................... measured at jambs on a horizontal line
parallel to the plane of the face; not to ex-
ceed 0.0625 in (1.5 mm)
e. Twist...............................................................measured at opposite face corners of jambs
on parallel lines perpendicular to the plane
of the door rabbet; not to exceed 0.0625 in
(1.5 mm)
f. Plumbness.....................................................measured at the jambs on a perpendicular
line from the head to the floor; not to exceed
0.0625 in (1.5 mm)

14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 The above tolerances provide a reasonable guideline for proper installation of hollow metal
frame product. However, it should be noted that the cumulative affect of the installation toler-
ances at or near their maximum levels could result in sufficient misalignment to prevent the
door from functioning properly. Installers should be careful not to create a tolerance buildup.
Tolerance buildup occurs when several tolerances are at or near their maximums.
3. The details in Figure 4 illustrate the method of measuring the above specified tolerances.
4. Grout guards and junction boxes are intended to protect hardware mortises and tapped holes from
masonry grout of 4 in. (101 mm) maximum slump consistency which is hand troweled in place.
If a lighter consistency grout (greater than 4 in. (101 mm) slump when tested in accordance with
ASTM C 143/C 143M) is to be used, special precautions must be taken in the field by the installer
to protect the aforementioned.
5. Frame products are not intended or designed to act as forms for grout or concrete. Take precau-
tions otherwise to ensure that frames are not deformed or damaged by the hydraulic forces that
occur during this process.
6. Keep steel surfaces free of grout, tar, and/or other bonding materials or sealers. Promptly clean
grout, tar, and/or other bonding materials or sealers off of doors and frame product. If the primer
is removed, damaged or negitivly affected by this process, promptly finished smooth, cleaned,
treated for maximum paint adhesion and touched up with a rust inhibitive primer comparable to and
compatible with the shop applied primer and finish paint specified in Section 09 90 00. All touch-up
primer and finish paint must be formulated for Direct to Metal (DTM) application.
7. Install labeled fire doors and frame product in accordance with the terms of their listings, ANSI/
NFPA 80 or the local Authority Having Jurisdiction.
8. Maintain proper door edge clearances in accordance with Section 3.03, except for special condi-
tions otherwise noted. Where necessary, metal hinge shims, furnished by the installer, are permit-
ted to maintain clearances.
9. Exposed hollow metal surfaces which have been scratched or otherwise marred during installa-
tion, cleaning, and/or field welding, shall promptly be finished smooth, cleaned, treated for max-
imum paint adhesion and touched up with a rust inhibitive primer comparable to and compatible
with the shop applied primer and finish paint specified in Section 09 90 00. All touch-up primer and
finish paint must be formulated for Direct to Metal (DTM) application.
10. Install hardware in accordance with hardware manufacturer’s templates and instructions.
11. Finish paint in accordance with Section 09 90 00.
See NAAMM HMMA 840 TN01, Painting Hollow Metal Products.
12. Install door silencers.
13. Install glazing materials in accordance with Section 08 80 00.
3.03 CLEARANCES
A. Ensure that the edge clearance for swinging hollow metal doors provides for the functional operation
of the assembly and does not exceed the following:
1. Between doors and frame product at head and jamb..........0.125 in (3.1 mm) +/- 0.0625 in (1.5 mm)
2. Between edges of pairs of doors.........................................0.125 in (3.1 mm) +/- 0.0625 in (1.5 mm)
B. Floor clearance for fire-protection rated swinging hollow metal doors shall not exceed 0.75 in (19.0
mm). Floor clearance shall be provided for the functional operation of all swinging hollow metal
doors and shall not be less than 0.125 in (3.1 mm).
The architect must define the distance from top of the floor/finished floor to top of floor cov-
ering so appropriate undercuts can be provided. Floor/Finish Floor is defined as the top of
the concrete or structural slab. HMMA uses the term “top of floor covering” to describe the
NFPA term “nominal surface of floor covering”. Refer to HMMA’s Tech Note, HMMA 810
TN01-03, “Defining Undercuts”, included as Appendix 3 for further guidance.

END OF SECTION

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 15

 CONTINUOUS WELD CORNER JOINT

NOTE: Joint design may vary; see HMMA-820, “Hollow Metal Frames”
for representative corner joint details

FACE WELD

BUTTED AND FACE WELDED JOINTS

FIGURE #1

16 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

  

THROAT OPENING FRAME DEPTH

+/- 3/32 IN. (2.4 mm) +/- 1/16 IN. (1.5 mm)

RABBET +/- 1/32 IN. (0.8 mm)

(door/glass/panel)

FACE STOP
+/- 1/32 IN. (0.8 mm) +/- 1/32 IN. (0.8 mm)

 
Figure #2
Sectional Profile Tolerances

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 17

 WOOD
PLANKING

WOOD
PLANKING

WOOD
PLANKING

Figure #3STORAGE
RECOMMENDED
Recommended
Figure 3 Storage

18 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 OPENING WIDTH, MEASURED
HORZONTALLY FROM RABBET TO
RABBET AT TOP, MIDDLE AND
BOTTOM OF FRAME + 1/16 IN
(1.5 mm) - 1/32 IN (0.8 mm)
1/16"

SQUARENESS; MEASURED AT 1/16"

RABBET ON A LINE FROM JAMB 90.0°
PERPENDICULAR TO FRAME HEAD

HEAD

HINGE OR
STRIKE JAMB
OPENING HEIGHT; MEASURED
VERTICALLY BETWEEN FRAME
HEAD RABBET AND TOP OF
FLOOR OR BOTTOM OF FRAME
MINUS JAMB EXTENSIONS AT
EACH JAMB AND ACROSS THE
HEAD; + 1/16 IN ( 1.5 mm) ,
- 1/32 IN ( 0.8 mm) .

PLUMBNESS; MEASURED AT JAMB

ON A HORIZONTAL LINE FROM THE
HEAD TO THE FLOOR.

FLOOR

1/16"
1/16"
1/16"
LINE PARALLEL FACE

PROFILE MY VARY
ALIGNMENT; MEASURED AT JAMBS
AS A FUCTION OF
ON A HORIZONTAL LINE PARALLEL 1/16"
DESIGN
TO THE PLANE OF THE FACE.

PARALLEL LINES
TWIST; MEASURED AT OPPOSITE FACE
CORNERS OF JAMBS ON PARALLEL
LINES . PERPENDICULAR TO THE PLANE
OF THE DOOR RABBET.
1/16"
1/16"

Figure #4
InstallationTOLERANCES
INSTALLATION Tolerances

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES 19

 APPENDIX 1
(Not part of the Standard)
NAAMM/HMMA 803-08 - STEEL TABLES
Prior to 1970, sheet steel was referred to by gage. ASTM and ANSI currently do not list gage numbers in
their standards. Like many generic terms, gage (or gauge) is ingrained in many vocabularies and is misun-
derstood as a term for thickness. NAAMM is publishing this minimum thickness table to be used instead of
discontinued gage numbers.
The decimal inch values shown were taken from the Underwriters Laboratories, Inc. publication for gage num-
ber and equivalent thickness. Corresponding metric values are included for reference purposes only.

MINIMUM THICKNESS CONVERSION

(Uncoated Steel Sheet) Fractional Decimal Inch mm
Gage Decimal Inch mm Inch
1.000 25.40
4 0.214 5.43
15/16 0.937 23.81
5 0.199 5.05
7/8 0.875 22.22
6 0.184 4.67
13/16 0.812 20.63
7 0.167 4.24
3/4 0.750 19.05
8 0.152 3.86
11/16 0.687 17.46
10 0.123 3.12
5/8 0.625 15.87
12 0.093 2.36
9/16 0.562 14.28
14 0.067 1.70
1/2 0.500 12.70
16 0.053 1.34 7/16 0.437 11.11
18 0.042 1.06 3/8 0.375 9.52
20 0.032 0.81 5/16 0.312 7.93
22 0.026 0.66 1/4 0.250 6.35
24 0.020 0.50 3/16 0.187 4.76
26 0.016 0.40 1/8 0.125 3.17
28 0.013 0.33 1/16 0.062 1.58

DISCLAIMER
This sheet was developed by representative members of the Hollow Metal Manufacturers Association Division
(HMMA) of the National Association of Architectural Metal Manufacturers (NAAMM) to provide their opinion
and guidance on minimum thickness and corresponding metric equivalents used for hollow metal doors and
frames. This sheet contains advisory information only and is published as a public service by the HMMA
Division.
NAAMM AND ITS HMMA DIVISION DISCLAIM ALL LIABILITY OF ANY KIND FOR THE USE, APPLICATION
OR ADAPTATION OF MATERIAL SHOWN ON THIS SHEET

A1 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

 APPENDIX 2
(Not part of the Standard)

GROUTING HOLLOW METAL FRAMES

HMMA-820 TN01-03

Grout, when used in accordance with industry guidelines can improve frame durability, sound deadening
and, depending on wall construction, increases frame anchorage strength. Grouting of the frame does not
increase door durability, nor is it required for fire-rated frames. For most commercial applications, grouting of
mullions and other closed sections is not recommended.
For applications covered by ANSI/NAAMM HMMA 862, “Guide Specifications for Commercial Security Hollow
Metal Doors and Frames” and ANSI/NAAMM HMMA 863, “Guide Specifications for Detention Security Hollow
Metal Doors and Frames”, the standards require that “frame jambs shall be fully grouted to provide added
security protection against battering, wedging, spreading, and other means of forcing open the door”.
Grout is a water-based product. If not used properly, it can destroy the opening in a very short time. Grout
can be either “mortar”, which is a masonry mixture of lime, cement, sand and water, or “plaster”, a gyp-
sum-based product.
Plaster grout dries with exposure to air. When a frame member is filled solid with plaster grout, only those
areas exposed to air will dry and harden, while the center remains wet (uncured). The water remaining in the
plaster grout can rust the frame from the inside.
Mortar grout cures by chemical reaction and hardens throughout. Use mortar grout.
Frames are not designed to act as forms for grout. Grout must have a maximum 4 in. slump and be hand
troweled in place. Bracing of the frame may be necessary prior to grouting to prevent sagging of the header
or bowing of the jamb due to weight or pressure of the grout. Grout should not be installed after gypsum wall-
board is installed, as the liquid within the grout will deteriorate the wallboard.
When dictated by temperatures, anti-freezing agents for mortar may be recommended by specifications.
These agents can adversely affect metal and all surfaces in contact with grout must be coated with a corro-
sion resistant material.
It is recommended that the contractor be responsible for the grouting and for any additional barrier coating. It
is also the contractor’s responsibility to use care in the application of the grout.

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES A2

 APPENDIX 3
(Not part of the Standard)
DEFINING UNDERCUTS
HMMA-810 TN01-03
Review of established definitions.
1. “ACTUAL DOOR HEIGHT” - The door opening CLEARANCE
height minus top clearance and undercut.
-
2. “DOOR OPENING HEIGHT” - The distance mea-
sured vertically between the frame head rabbet

ACTUAL DOOR HEIGHT

DOOR OPENING HEIGHT

and top of floor or bottom of frame minus jamb -
extension.
3. “FINISHED FLOOR” - See “Floor”
4. “FLOOR” - The top of the concrete or structural BOTTOM
OF FRAME
slab. FLOOR

5. “FLOOR CLEARANCE” - The distance between

the bottom of the door and the top of the material UNDERCUT,
directly below the door. This varies with applica- FLOOR CLEARANCE

tion, such as concrete, any floor covering and/or Figure # 1

a threshold.
Floor coverings; such as carpet, resilient or ceramic
6. “FLOOR COVERING” - Any material applied on tile, are typically installed on top of the floor, fitted
top of the floor that extends under the door in its around the frame, and under the door. In this situ-
closed position or under the door as it swings to ation, the formula for figuring Undercut is the total
its fully open position. of the Floor Clearance + Floor Covering Thickness.
7. “UNDERCUT” - The distance between the bot- See Figure # 2.
tom of door and the bottom of frame. The formula

ACTUAL DOOR HEIGHT

DOOR OPENING HEIGHT

in which to determine Undercut is derived by add-
ing the total sum of the following (Floor Clearance
BOTTOM
+ Floor Covering Thickness + Threshold Height OF FRAME
(assuming the threshold is mounted on top of the FLOOR
COVERING
floor covering) + Jamb Extensions Height).
FLOOR
8. “JAMB EXTENSIONS” - That portion of a jamb
or mullion which extends below the level of the FLOOR CLEARANCE
floor. UNDERCUT

Figure # 2
Typically frames are intended to be installed directly
on the floor. When no floor coverings or thresholds When a threshold is used, it is installed on top of
are used, the dimension for “Undercut” is the same the floor or floor covering, fitted around the frame
as for “Floor Clearance”. See Figure # 1. and under the door. Again the formula for figuring
“Undercut” changes. Undercut is the total of the
Floor Clearance + Threshold Height + Floor Covering
Thickness. See Figure # 3.
ACTUAL DOOR HEIGHT

DOOR OPENING HEIGHT

THRESHOLD
BOTTOM
OF FRAME
FLOOR
COVERING

FLOOR

FLOOR CLEARANCE
UNDERCUT

Figure # 3

A3 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

In situations with specialized floors such as thick ce-

ACTUAL DOOR HEIGHT

ramic tile or terrazzo, the frame is typically installed

DOOR OPENING HEIGHT

prior to the installation of the floor.
One method is to install the frame with adjustable

UNDERCUT
BOTTOM
floor anchors or for the frame to be installed on OF FRAME
a block or shim. This allows the frame to be po-
sitioned, as required, to accommodate the floor FLOOR

height. See Figures # 4A and 4B. Both illustrate a

raised frame condition in which the bottom of frame
is positioned to be directly on top of the floor after
the floor is installed. In this situation, the dimension FLOOR CLEARANCE JAMB
EXTENSION
measured for Undercut is also the same as Floor
Clearance. Figure # 5A

DOOR OPENING HEIGHT

ACTUAL DOOR HEIGHT
ACTUAL DOOR HEIGHT

DOOR OPENING HEIGHT

UNDERCUT
BOTTOM
OF FRAME
BOTTOM
OF FRAME FLOOR

FLOOR

FLOOR CLEARANCE JAMB

EXTENSION
ADJUSTABLE FLOOR CLEARANCE,
FLOOR ANCHOR UNDERCUT
Figure # 5B
Figure # 4A
The Architect/Designer must be very specific within
ACTUAL DOOR HEIGHT

DOOR OPENING HEIGHT

specifications and contract drawings, which should

include detailed drawings illustrating conditions for
each floor, including thicknesses and materials.
BOTTOM These drawings should designate the height at which
the hollow metal frame should be set. Thresholds
OF FRAME

FLOOR and hardware items requiring specific floor clearanc-

es shall be listed in the hardware schedule, which
allows the door and frame manufacturer to properly
size each opening.
FLOOR CLEARANCE,
BLOCKING
UNDERCUT Within the door and frame industry, both the Hollow
Metal Manufacturers Association (HMMA) a division
Figure # 4B of the National Association of Architectural Metal
Manufacturers (NAAMM) and the Steel Door Insti-
tute (SDI), publish recommended clearances. In
Another method, called “below floor installation”, is to addition, the National Fire Protection Association
install the frame directly on the rough slab. After the (NFPA) Publication 80, “Standard for Fire Doors and
frame is installed, the floor is then installed around Fire Windows”, regulates the installation and mainte-
the frame. That portion of the frame is covered by nance of labeled openings, and lists several different
the floor and is called jamb extensions. The formula scenarios consisting of different floor materials and
for figuring “Undercut” is the total of the Floor Clear- the maximum clearance under the bottoms of doors.
ance + Jamb Extensions. See Figures # 5A and 5B.

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES A4

 APPENDIX 4
(Not part of the Standard)
STANDARDS DEVELOPMENT ORGANIZATIONS

ANSI American National Standards Institute, Inc.

11 West 42nd Street
New York, NY 10036
Tel: (212) 642-4900
Website: www.ansi.org
ASTM ASTM International
100 Barr Harbor Drive
West Conshohocken, PA 19428-2959
Tel: (610) 832-9585
Website: www.astm.org
ICC International Code Council
500 New Jersey Avenue NW
6th Floor
Washington, DC 20001-2070
Tel: 1 (888) 422-7233
Website: www.iccsafe.org
NAAMM National Association of Architectural Metal Manufacturers
800 Roosevelt Road
Building C, Suite 312
Glen Ellyn, IL 60137
Tel: (630) 942-6591
Website: www.naamm.org
NFPA National Fire Protection Association
1 Batterymarch Park
P.O. Box 9101
Quincy, MA 02269
Tel: (617) 770-3000
Website: www.nfpa.org
UL Underwriters Laboratories, Inc.
333 Pfingsten Road
Northbrook, Illinois 60062
Tel: (847) 272-8800
Website: www.ul.com

A5 COMMERCIAL HOLLOW METAL DOORS AND FRAMES ANSI/NAAMM HMMA 861-14

ANSI/NAAMM HMMA 861-14 COMMERCIAL HOLLOW METAL DOORS AND FRAMES
RECOMMENDED GUIDE SPECIFICATIONS FOR
HOLLOW METAL DOORS AND FRAMES
HMMA 860- Hollow Metal Doors and Frames
ANSI/NAAMM
HMMA 861- Commercial Hollow Metal Doors and Frames
ANSI/NAAMM
HMMA 862- Commercial Security Hollow Metal Doors and Frames
ANSI/NAAMM
HMMA 863- Detention Security Hollow Metal Doors and Frames
NAAMM
HMMA 865- Sound Control Hollow Metal Door and Frame Assemblies
ANSI/NAAMM
HMMA 866- Stainless Steel Hollow Metal Doors and Frames
ANSI/NAAMM
HMMA 867- Commercial Laminated Core Hollow Metal Doors and Frames
RELATED HMMA DOCUMENTS
HMMA 800- Introduction to Hollow Metal
ANSI/NAAMM
HMMA 801- Glossary of Terms for Hollow Metal Doors and Frames
HMMA 802- Manufacturing of Hollow Metal Doors and Frames
HMMA 803- Steel Tables
HMMA 810- Hollow Metal Doors
HMMA 820- Hollow Metal Frames
HMMA 830- Hardware Selection for Hollow Metal Doors and Frames
HMMA 831- Recommended Hardware Locations for Hollow Metal Doors and Frames
HMMA 840 - Installation and Storage of Hollow Metal Doors and Frames
ANSI/NAAMM
HMMA 841- Tolerances and Clearances for Commercial Hollow Metal Doors and Frames
HMMA 850- Fire-Rated Hollow Metal Doors and Frames
HMMA 890- Technical Summary
HMMA 810-TN01 - Defining Undercuts
HMMA 820-TN01 - Grouting Hollow Metal Frames
HMMA 820-TN02 - Continuously Welded Frames
HMMA 820-TN03 - Guidelines for Glazing Hollow Metal Transoms, Sidelights and Windows
HMMA 840-TN01 - Painting Hollow Metal Products
HMMA 840-TN02 - Maintenance of Installed Hollow Metal Products