Scribd
Upload
239 views

Week 5 Assignment 5 Solution Full Marks: 20: W + W - T 75 + 40 - 10 105 MM

This document contains solutions to 9 questions regarding design tensile strength calculations for structural members from IS 800:2007. 1) The design tensile strength due to yielding of the gross section of a member (Tdg) is given by Agfy/γm0. 2) The design tensile strength due to rupture of the critical section of a plate is given by 0.9Anfu/γm1. 3) A gusset plate is used to connect two or more structural members intersecting each other.

Uploaded by

amin alzuraiki
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
239 views

Week 5 Assignment 5 Solution Full Marks: 20: W + W - T 75 + 40 - 10 105 MM

This document contains solutions to 9 questions regarding design tensile strength calculations for structural members from IS 800:2007. 1) The design tensile strength due to yielding of the gross section of a member (Tdg) is given by Agfy/γm0. 2) The design tensile strength due to rupture of the critical section of a plate is given by 0.9Anfu/γm1. 3) A gusset plate is used to connect two or more structural members intersecting each other.

Uploaded by

amin alzuraiki
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Week 5 Assignment 5 Solution Full Marks: 20

Q.1 The design tensile strength of a member due to yielding of gross section, Tdg is
given by 1
(c) Agfy/m0
Solution: Cl. 6.2, IS 800: 2007.

Q.2 The design tensile strength of a plate due to rupture of critical section is given
by 1
(a) 0.9Anfu/m1

Solution: Cl. 6.3.1, IS 800: 2007.

Q.3 The slenderness ratio for a member if always in tension (other than pre-
tensioned member) is 1
(b) 400
Solution: Table 3, IS 800: 2007

Q.4 A plate used for connecting two or more structural members intersecting each
other is 1
(c) Gusset plate

Q.5 An ISA 150×75×10 is connected to a gusset plate of thickness 12mm by four


M18 grade 4.6. The Tensile strength governed by yielding of gross section of
the angle if gusset is connected to the longer leg is 2
(d) 490 kN
Solution: Gross area of the angle, Ag = 2156 mm2
𝑓𝑦 ×𝐴𝑔 250×2156
𝑇𝑑𝑔 = = × 10−3 = 490 kN
𝛾𝑚0 1.1

Q.6 The shear lag width for ISA 75X75X10 is (Assume gauge distance = 40 mm) 2
(b) 105 mm
Solution: The length of outstanding leg will be w = 75 mm and w1 = 40 mm.
So the shear lag width, bs = w + w1 – t = 75 + 40 – 10 = 105 mm.

Q.7 A single angle section 90X60X10 is connected with gusset plate with 7 bolts of 20
mm diameter in one line at pitch of 50 mm and edge distance of 30 mm. What is
the design tensile strength of the section for rupture of net section? (Assume the
section is connected with longer leg and gauge distance = 50 mm) 4
(a) 349 kN
Solution: Anc = (90 - 10/2 - 22) × 10 = 630 mm2
Ago = (60 - 10/2) × 10 = 550 mm2
An = 630 + 550 = 1180 mm2
The length of outstanding leg will be w = 60 mm and w1 = 50 mm.
So the shear lag width, bs = w + w1 – t = 60 + 50 – 10 = 100 mm.
Distance between end bolts , Lc = 6 × 50 = 300 mm.
𝑏 𝑤 𝑓𝑦 100 60 250
𝛽 = 1.4 − 0.076 𝐿𝑠 × × 𝑓 = 1 .4 − 0.076 × 300 × 10 × 410 = 1.307
𝑐 𝑡 𝑢

0.9𝑓𝑢 𝐴𝑛𝑐 𝛽𝑓𝑦 𝐴𝑔𝑜 0.9×410×630 1.307×250×550


Thus, 𝑇𝑑𝑛 = + = +
𝛾𝑚1 𝛾𝑚0 1.25 1.1

= 349.35 × 103 N = 349.35 kN.

Q.8 A single ISA 75 × 50 × 8 is connected (longer leg) with gusset plate using use 4
bolts of 20 mm diameter in one line at pitch of 50 mm and edge distance of 30
mm. What is the Design tensile strength due to block shear failure? (Assume
gauge distance = 35 mm) 4
(c) 213 kN

Solution:
Avg = 8 × (3 × 50 + 30) = 1440 mm2
Avn = 8 × (3 × 50 + 30 – 3.5 × 22) = 824 mm2
Atg = 8 × 40 = 320 mm2 [assuming gauge g = 35 for 75 mm leg]
Atn = 8 × (40 – 0.5 × 22) = 232 mm2
0.9𝐴𝑣𝑛 𝑓𝑢 𝑓𝑦 𝐴𝑡𝑔 0.9×410×824 250×320
𝑇𝑑𝑏1 = + = + = 213.16 × 103 N = 213.16 kN
√3𝛾𝑚1 𝛾𝑚0 √3×1.25 1.1

𝐴𝑣𝑔 𝑓𝑦 0.9 𝑓𝑢 𝐴𝑡𝑛 1440×250 0.9×410×232


𝑇𝑑𝑏2 = + = + = 257.44 × 103 N = 257.44 kN
√3𝛾𝑚0 𝛾𝑚1 √3×1.1 1.25

So, Tdb = 213.16 kN.

Q.9 An ISA 90  90  8 used as tension member is connected to a 10 mm gusset


plate by fillet weld of size 5 mm. The design strength of the member is 300
kN. Calculate the length of the weld. 4
(a) lower side 324 mm and upper side 125 mm

90−25.1
Solution: Force resisted by weld at lower side of angle P1 = 300 × = 216.33 kN
90
25.1
Force resisted by weld at upper side of angle P2 = 300 × = 83.67 kN
90

Assuming size of weld as 5mm, the throat thickness te will be 0.707 × 5 = 3.535 mm

𝑃1 216.33 ×103
Length required at lower side Lw1 = 𝑡𝑒 𝑓𝑢 = 3.535×410 = 323.15 mm ≈ 324 mm
√3𝛾𝑚𝑤 √3×1.25

𝑃2 83.67 ×103
Length required at upper side Lw2 = 𝑡𝑒 𝑓𝑢 = 3.535×410 = 124.9 mm ≈ 125 mm
√3𝛾𝑚𝑤 √3×1.25

You might also like