Design Project VN 2013

EE332 Design Project
“Variable Gain Amplifier with Output Stage Optimization for Audio Amplifier
Applications”
Overview:
This design project aims to utilize every single skill you have learned in EE 332 this
quarter. You will use your newly acquired knowledge to build a useful product that
could potentially be subsequently refined and sold. This is the second step, after
marketing, of a typical commercial production process: creating a working prototype.
Your job is to simulate an audio amplifier that can take the input from a CD player or
portable music player and amplify the signal to drive a loudspeaker. Your design can
utilize any passive electronic components, discrete BJT’s or MOSFET’s (array chips are
okay too), and operational amplifier’s (with some specific guidelines). Listed below are
some project specifications as well as the equipment that is available to you:
Input signal specifications:

Signal voltage: 1.0 VAC
Signal source resistance 50 Ω
Equipment available for testing: Software: PSPICE, LTSPICE etc.
Minimum Design Specifications of the amplifier:

Output power: 0.5W (minimum)
Load Impedance (speaker): 8Ω
Unity Gain Bandwidth: 20Hz – 20 kHz (-3dB)
Idling power: < 1W
Distortion: No distortion
Design Description:
A skeleton description of what your design may look like is as follows:

Your amplifier will take a small signal input from a music player, and then presumably
send it into a gain stage to meet the gain requirements for the design. As you have
learned, we will need a specially designed output stage to drive a speaker resistance of 8
ohms.
As you may have noticed, the input signal specifications provide a large range of input
amplitudes. There are a number of reasons for this. The first is to ease requirements for
simply meeting specifications, while leaving SIGNIFICANT room for optimization. Also,
input signal specifications from a music source are not always easily accessible, so this
will give you some flexibility to tune your amplifier to achieve good sound quality. And
finally, the .5W specification may be very loud for a speaker. The flexibility of your
amplifier will allow you to vary the gain for better audio quality.
Thus, the audio amplifier you design must be more flexible than audio amplifiers you are
used to, since you must be able to handle a wide range of inputs, and still tune the gain
to achieve .5W on the output.
Design Decision Justification:
There is no specific topology that you should follow, the method is open-ended and you
are free to explore any resources. With this in mind, the decisions and tradeoffs you
make in your design will be critical in determining the overall quality of your project, and
thus will play a significant role in the final grade.
You must justify all blocks in your design. Why did you implement a given output stage?
Which component did you use and why? It is encouraged to meet specifications while
looking to optimize performance (output power or bandwidth. This is a great
opportunity to design something that is truly yours, so use it that way.
Optimization:
There is much room for improvement to exceed the specifications. Please aim to meet
the specifications first (it may not be as easy as you think!), and then look to optimize an
aspect of your design.
Timeline:
You are highly encouraged to start early. I anticipate that this will take about 12 hours
each person of the group to complete. In order to guide you through this process,
Project Report Requirements
Introduction
 Briefly explain the objective of the project
Architecture Design
 Design specifications
 Block Diagrams
 Discussion on the chosen architecture
 Trade offs
Circuit Design
 Schematics
 Design equations and calculations
 Simulation results
Results
Maximum Output Power
- What is the largest Vpk-pk on output that is not distorted/clipping and greater
than or equal to .5W while achieving -3dB bandwidth of 20Hz-20KHz?
Idling power
- DC power used with no input
Grading:
Report: 100%
Functionality: 40%
Justification: 60%

Design Project VN 2013

Uploaded by

Copyright:

Available Formats

Design Project VN 2013

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design Project VN 2013

Uploaded by

Copyright:

Available Formats

EE332 Design Project

Input signal specifications:

Minimum Design Specifications of the amplifier:

A skeleton description of what your design may look like is as follows:

Design Decision Justification:

Project Report Requirements

You might also like