2300

2/2-way Angle-Seat Control Valve

with stainless steel design for media
up to +180ºC, DN 13-50

• Excellent control characteristic and high flow rates

• High cycle life
• Clean design for optimal use in hygienic environment
• Quality certifications available

Type 2300 can be combined with...

Type 8692/8693 Type 8694 Type 8696 Type 8137 Typ 8222
Positioner / Process Positioner Positioner Radar level Conductivity
Controller TopControl TopControl Basic TopControl Basic transmitter transmitter

In line with Bürkert’s philosophy for modular Technical data

valves and sensors the construction of the Orifice DN 13 to 50
2300 angle-seat valve fulfils tough criteria for
Port connections
process environments. Unrivalled cycle life and Threaded port acc. to G 1/2 to G 2, NPT 1/2 to NPT 2, Rc 1/2 to Rc 2
sealing integrity is guaranteed by the proven Welded acc. to EN ISO 1127, DIN 11850 S2, ASME BPE, SMS 3008,
self adjusting packing gland. BS 4825
Clamp acc. to ISO 2852, ASME BPE
The parabolic trim results in a flow characteris- Body material Stainless steel 316L
tic approximately 35% larger than conventional Actuator material
control valves. It is available in either stainless Actuator PPS
steel on stainless steel or with a durable PTFE Cover Stainless steel 1.4561 (316Ti)
seal for tight shut-off. Plug sealing PTFE/St.st. (PTFE/stainless steel) and
St.st./St.st. (stainless steel/stainless steel)
The design enables the easy integration of au- Seat leakage IEC 534-4/EN Shut-off class IV for St.st./St.st.
tomation modules whether they are digital elec- 1349 Shut-off class VI for PTFE/St.st.
tropneumatic positioner or process controller. Media Water, alcohol, oils, fuels, hydraulic fluids, salt solution,
alkali solutions, organic solvents, steam
The fully integrated system has a compact and Viscosity max. 600 mm2/s
smooth design, integrated pneumatic lines, Packing gland PTFE V-rings with spring compensation
IP65/67/NEMA4X protection class and supe-
Medium temperature -10 to +180 ºC (max. +130°C for PTFE/St.st. sealing recommended)
rior chemical resistance.
Ambient temperature 0 to +60 ºC
Control medium Compressed air
This system has been engineered for reliable
Pilot pressure 5.5 to 7 bar
accurate control in applications where high
flow rate is an advantage. Pilot air ports Push-in connector for external ø 6 mm or 1/4” tube
Installation As required, preferably with actuator in upright position

Content
Valve specifications System spec. Continuous ELEMENT Request for quotation

Type 2300 Type 8802-YG Type 8802-YG

Technical data & ordering info. p. 1-7 Ordering info. & technical data p. 8-15 p. 16

www.burkert.com p. 1/16
 2300

Technical data Type 2300, continued

Kv values water/pressure
Orifice Actuator size Kv value water Minimum pilot pressure Operating pressure up to +180º
[mm] [mm] (m3/h) [bar] SFA [bar] SFB [bar]
13 50 5.0 5.5 16 16
20 70 9.5 5.5 16 16
25 70 15.45 5.5 16 16
32 70 22.0 5.5 8.5 16
40 90 31.9 5.5 16 16
50 90 47.0 5.5 10 16
Flow rate: Kv value water [m3/h]: Measured at +20 °C, 1 bar pressure at valve inlet and free outlet.
Pressure valves [bar]: Overpressure to the atmospheric pressure

Flow characteristic

Kv /Kvs [%]
100
90
80
70
60
50
40
30 Remarks on the flow characteristic
20 Modified equi-percentile flow characteristic, engineered for
10 a quick response during peak flow demand (an advantage for
0 many processes like heating/cooling with heat exchangers)
0 10 20 30 40 50 60 70 80 90 100
Stroke [%] and fine control at lower flow.
Flow rate standard control valve

Kvs values [m3/h]

Port size Stroke [%]
and orifice
[mm] 2.5 5 10 20 30 40 50 60 70 80 90 100
13/15 0.12 0.14 0.17 0.4 2.2 3.5 4.2 4.5 4.7 4.9 5.0 5.0
20 0.18 0.19 0.21 0.32 0.87 3.64 5.7 6.8 7.9 8.6 9.1 9.5
25 0.18 0.19 0.23 0.5 1.33 4.84 7.94 9.85 11.65 13.36 14.5 15.45
32 0.4 0.4 0.5 0.8 1.4 4.0 9.4 13.0 15.8 18.1 20.1 22.0
40 0.5 0.6 0.7 1.3 3.3 10.6 16.3 20.8 24.2 26.3 29.8 31.9
50 0.7 0.9 1.1 1.6 5.2 16.0 22.5 27.7 32.8 37.8 42.5 47.0

p. 2/16
 2300

Ordering chart Type 2300, flow direction below the seat (for gases and liquids)
G threaded port

pressure up to
pressure [bar]

St. st./St. st.

+180°C [bar]
Orifice [mm]

plug sealing

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.

Item no.
Control

thread
Port
A 2/2-way valve, 13 50 G 1/2 5.5 16 203 318 206 222
NC 20 70 G 3/4 5.5 16 203 494 206 225
A 25 70 G1 5.5 16 203 496 206 227
32 70 G 1 1/4 5.5 8.5 203 497 206 228
40 90 G 1 1/2 5.5 16 203 498 206 229
P
50 90 G2 5.5 10 203 500 206 230
B 2/2-way valve, 13 50 G 1/2 5.5 16 203 501
NO 20 50 G 3/4 5.5 16 203 503
B 25 50 G1 5.5 16 203 506
32 70 G 1 1/4 5.5 16 203 508
40 90 G 1 1/2 5.5 16 203 509
P
50 90 G2 5.5 16 203 510

NPT threaded port

pressure up to
pressure [bar]

St. st./St. st.

+180°C [bar]
Orifice [mm]

plug sealing

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.

Item no.
Control

thread
Port

A 2/2-way valve, 13 50 NPT 1/2 5.5 16 203 529 206 231

NC 20 70 NPT 3/4 5.5 16 203 532 206 234
A 25 70 NPT 1/2 5.5 16 203 534 206 236
32 70 NPT 1 1/4 5.5 8.5 203 535 206 237
40 90 NPT 1 1/2 5.5 16 203 536 206 238
P
50 90 NPT 2 5.5 10 203 537 206 239
B 2/2-way valve, 13 50 NPT 1/2 5.5 16 203 538
NO 20 50 NPT 3/4 5.5 16 203 540
B 25 50 NPT 1/2 5.5 16 203 542
32 70 NPT 1 1/4 5.5 16 203 544
40 90 NPT 1 1/2 5.5 16 203 545
P
50 90 NPT 2 5.5 16 203 546

RC threaded port
pressure [bar]

St. st./St. st.

Orifice [mm]

plug sealing

plug sealing
PTFE/St. st.
size Ø [mm]

pressure up
connection

Operating

to +180°C
Min. pilot
Actuator
function

Item no.

Item no.
Control

thread

[bar]
Port

A 2/2-way valve, 13 50 RC 1/2 5.5 16 203 547 206 240

NC 20 70 RC 3/4 5.5 16 203 550 206 243
A 25 70 RC 1/2 5.5 16 203 552 206 245
32 70 RC 1 1/4 5.5 8.5 203 553 206 246
40 90 RC 1 1/2 5.5 16 203 554 206 248
P
50 90 RC 2 5.5 10 203 555 206 249
B 2/2-way valve, 13 50 RC 1/2 5.5 16 203 556
NO 20 50 RC 3/4 5.5 16 203 558
B 25 50 RC 1/2 5.5 16 203 560
32 70 RC 1 1/4 5.5 16 203 562
40 90 RC 1 1/2 5.5 16 203 563
P
50 90 RC 2 5.5 16 203 564

p. 3/16
 2300

Ordering chart Type 2300, flow direction below the seat (for gases and liquids), continued
Weld end acc. to EN ISO 112

pressure up to
pressure [bar]
tube-Ø [mm]

St. st./St. st.

+180°C [bar]
Orifice [mm]

plug sealing

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.

Item no.
Control

Port
A 2/2-way valve, 15 50 21.3 x 1.6 5.5 16 203 565 206 250
NC 20 70 26.9 x 1.6 5.5 16 203 568 206 254
A 206 256
25 70 33.7 x 2 5.5 16 203 570
32 70 42.4 x 2 5.5 8.5 203 571 206 257
P 40 90 48.3 x 2 5.5 16 203 572 206 258
50 90 60.3 x 2.6 5.5 10 203 573 206 259
B 2/2-way valve, 15 50 21.3 x 1.6 5.5 16 203 574
NO 20 50 26.9 x 1.6 5.5 16 203 576
B 5.5
25 50 33.7 x 2 16 203 578
32 70 42.4 x 2 5.5 16 203 580
P 40 90 48.3 x 2 5.5 16 203 581
50 90 60.3 x 2.6 5.5 16 203 582

Weld end acc. to DIN 11850 S2

pressure up to
pressure [bar]
tube-Ø [mm]

+180°C [bar]
Orifice [mm]

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.
Control

Port

A 2/2-way valve, 15 50 19 x 1.5 5.5 16 203 583

NC 20 70 23 x 1.5 5.5 16 203 586
A
25 70 29 x 1.5 5.5 16 203 588
32 70 35 x 1.5 5.5 8.5 203 589
P 40 90 41 x 1.5 5.5 16 203 590
50 90 53 x 1.5 5.5 10 203 591
B 2/2-way valve, 15 50 19 x 1.5 5.5 16 203 592
NO 20 50 23 x 1.5 5.5 16 203 594
B 5.5
25 50 29 x 1.5 16 203 596
32 70 35 x 1.5 5.5 16 203 598
P 40 90 41 x 1.5 5.5 16 203 599
50 90 53 x 1.5 5.5 16 203 600

p. 4/16
 2300

Ordering chart Type 2300, flow direction below the seat (for gases and liquids), continued
Weld end acc. to ASME BPE

pressure up to
pressure [bar]
tube-Ø [mm]

+180°C [bar]
Orifice [mm]

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.
Control

Port
A 2/2-way valve, 15 50 12.7 x 1.65 5.5 16 203 601
NC 20 70 19.05 x 1.65 5.5 16 203 604
A
25 70 25.4 x 1.65 5.5 16 203 606
40 90 38.1 x 1.65 5.5 16 203 607
P
50 90 50.8 x 1.65 5.5 10 203 608
B 2/2-way valve, 15 50 12.7 x 1.65 5.5 16 203 609
NO 20 50 19.05 x 1.65 5.5 16 203 611
B
25 50 25.4 x 1.65 5.5 16 203 613
40 90 38.1 x 1.65 5.5 16 203 615
P 50 90 50.8 x 1.65 5.5 16 203 616

Weld end acc. to SMS 3008

pressure up to
pressure [bar]
tube-Ø [mm]

+180°C [bar]
Orifice [mm]

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.
Control

Port

A 2/2-way valve, 15 50 12 x 1.0 5.5 16 203 617

NC 20 70 18 x 1.0 5.5 16 203 620
A
25 70 25 x 1.2 5.5 16 203 622
40 90 38 x 1.2 5.5 16 203 623
P
50 90 51 x 1.2 5.5 10 203 624
B 2/2-way valve, 15 50 12 x 1.0 5.5 16 203 625
NO 20 50 18 x 1.0 5.5 16 203 627
B
25 50 25 x 1.2 5.5 16 203 629
40 90 38 x 1.2 5.5 16 203 631
P 50 90 51 x 1.2 5.5 16 203 632

Weld end acc. to BS 4825

pressure up to
pressure [bar]
tube-Ø [mm]

+180°C [bar]
Orifice [mm]

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.
Control

Port

A 2/2-way valve, 15 50 12.7 x 1.2 5.5 16 203 633

NC A
20 70 19.05 x 1.65 5.5 16 203 636
25 70 25.4 x 1.65 5.5 16 203 638
P 40 90 38.1 x 1.65 5.5 16 203 639
50 90 50.8 x 1.65 5.5 10 203 640
B 2/2-way valve, 15 50 12.7 x 1.2 5.5 16 203 641
NO 20 50 19.05 x 1.65 5.5 16 203 643
B
25 50 25.4 x 1.65 5.5 16 203 645
40 90 38.1 x 1.65 5.5 16 203 647
P 50 90 50.8 x 1.65 5.5 16 203 648

p. 5/16
 2300

Ordering chart Type 2300, flow direction below the seat (for gases and liquids), continued
Clamp acc. to ISO 2852

clamp external

pressure up to
pressure [bar]

+180°C [bar]
Orifice [mm]

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.
Control

Ø [mm]
Port
A 2/2-way valve, 15 50 34.0 5.5 16 203 649
NC 20 70 50.5 5.5 16 203 652
A
25 70 50.5 5.5 16 203 654
32 70 50.5 5.5 8.5 203 655
P 40 90 64.0 5.5 16 203 656
50 90 77.5 5.5 10 203 657
B 2/2-way valve, 15 50 34.0 5.5 16 203 658
NO 20 50 50.5 5.5 16 203 660
B
25 50 50.5 5.5 16 203 662
32 70 50.5 5.5 16 203 664
P 40 90 64.0 5.5 16 203 665
50 90 77.5 5.5 16 203 666

Clamp acc. to ASME BPE

clamp external

pressure up to
pressure [bar]

+180°C [bar]
Orifice [mm]

plug sealing
PTFE/St. st.
size Ø [mm]

connection

Operating
Min. pilot
Actuator
function

Item no.
Control

Ø [mm]
Port

A 2/2-way valve, 15 50 25.0 5.5 16 203 667

NC 20 70 25.0 5.5 16 203 670
A
25 70 50.5 5.5 16 203 672
40 90 50.5 5.5 16 203 673
P 50 90 64.0 5.5 10 203 674
B 2/2-way valve, 15 50 25.0 5.5 16 203 675
NO 20 50 25.0 5.5 16 203 678
B
25 50 50.5 5.5 16 203 680
40 90 50.5 5.5 16 203 682
P 50 90 64.0 5.5 16 203 683

p. 6/16
 2300

Materials Type 2300

1 Pilot air ports Push-in connector PP (standard)

2 Actuator PPS
1 3 Cover Stainless steel 1.4561 (316Ti)
4 Piston seal FKM
5 Spring Stainless steel 1.4310
2 6 Pipe Stainless steel 1.4401 (316)
3
(1.4404 (316L) on request)
7 V-seals PTFE
4 8 Spindle Stainless steel 1.4401 (316)
(1.4404 (316L) on request)
5 9 Wiper PEEK
6 10 Plug Stainless steel 1.4571
11 Plug seal Stainless steel 1.4571 (+PTFE disc for
7 soft seat sealing)
8 12 Valve body Stainless steel 316L

10
11

12

p. 7/16
 2300
System Continuous
ELEMENT 8802-YG
Ordering information for valve system Continuous ELEMENT Type 8802-YG
A valve system Continuous ELEMENT Type 8802-YG consists of an angle-seat control valve Type 2300 and a digital electropneumatic Positioner
Type 8692, a digital electropneumatic Process Controller Type 8693 or a digital electropneumatic Positioner Basic Type 8694 (for valve actuator sizes
ø 70/90 mm) or a digital electropneumatic Positioner Type 8696 (for valve actuator size ø 50 mm) (see separate datasheets).
For the configuration of further valve systems pleasee use the "Request for quotation" on p. 16 GOôTOôPAGE

You order two components and receive a complete assembled and certified valve.

Ordering the valve system Continuous ELEMENT Type 8802-YG with valve actuator sizes ø 70/90 mm
Angle seat valve Type 2300 with
actuator sizes ø 70/ ø 90 mm Control unit

Type 8692 Type 8693 Type 8694

ô ô
 M  M
M M

Angle seat valve

with desired control unit

ô ô ô ô ô ô
 M  M Valve system  M  M Valve system  M  M Valve system
M M M M M M
Continuous Continuous Continuous
ELEMENT ELEMENT ELEMENT
Type 8802-YG-I Type 8802-YG-J Type 8802-YG-L
2300 + 8692 2300 + 8693 2300 + 8694

Click on the orange box "More info." below... you will come to our website for the resp. product where you can download the datasheet.

Positioner TopControl -OREô Process Controller -OREô Positioner TopControl Basic Type 8694 -OREô
Type 8692 INFO  TopControl Type 8693 INFO INFO

The new generation of integrated positioners for combination with actua-

tors from the process valve series Type 23xx/2103 is specially designed
for the requirements of hygienic process environments. The operation and
The new generation of integrated positioners/process controllers for com- selection of the software functions close tight function, inversion of the
bination with actuators from the process valve series Type 23xx/2103 is operating direction of the setpoint signal, characteristic curves selection
specially designed for the requirements of hygienic process environments. and switching manual/automatic operation are effected via push-buttons
The easy handling and the selection of additional software functions are and DIP switches or via the PC interface. The position setpoint is set using
done either on a big graphic display with backlight and keypad or via a PC the standard signal 4 - 20 mA. In addition, the enable can be controlled via
interface. A contact-free analog position sensor registers the valve position the binary input and an optional position feedback can be integrated.
without deterioration. Single-acting or double-acting actuators are control- The positioner, Type 8694, registers the valve position without deteriora-
led via the integral positioner system. With Type 8693, the process control- tion through a contact-free analogue position sensor. Single-acting or
ler function is superimposed on the position control loop. Profibus DPV1 double-acting actuators are controlled via the integral positioner system.
and DeviceNet communication interfaces are available as options. An AS-Interface communication interface is available as an option.
Main customer benefits: Main customer benefits:
• Compact design of the valve system with integrated positioner/process • Compact design of the valve system with integrated positioner
controller meets the demands for plant washdown environments meets the demands for plant washdown environments through the
through the selection of materials, external seals and integrated control selection of materials, external seals and integrated control air
air supply to the actuator supply to the actuator
• Extremely simple commissioning and operation thanks to the back- • Automatic parameterisation of the process controller using the
lighting of the graphics display and proven multilingual software structure Process TUNE function
• Automatic parameterisation of the positioner and process controller • Field bus communication via optional AS-Interface
using the TUNE functions • Air intake filter enhances the process valve system availability
• Field bus communication via Profibus DPV1 or DeviceNet • Simple and reliable actuator adaption allowing additional actuators
• Air intake filter enhances the process valve system availability of the process valve series, Type 20xx or actuators from other
• Simple and reliable actuator adaption manufacturers to be used
• Explosion-proof models for zone 2/22 • Explosion-proof models for zone 2/22

p. 8/16
 2300
System Continuous
ELEMENT 8802-YG
Ordering information for valve system Continuous ELEMENT Type 8802-YG, continued
A valve system Continuous ELEMENT Type 8802-YG consists of an angle-seat control valve Type 2300 and a digital electropneumatic Positioner
Type 8692, a digital electropneumatic Process Controller Type 8693 or a digital electropneumatic Positioner Basic Type 8694 (for valve actuator sizes
ø 70/90 mm) or a digital electropneumatic Positioner Type 8696 (for valve actuator size ø 50 mm) (see separate datasheets).
For the configuration of further valve systems pleasee use the "Request for quotation" on p. 16 GOôTOôPAGE

You order two components and receive a complete assembled and certified valve.

Ordering the valve system Continuous ELEMENT Type 8802-YG with valve actuator size ø 50 mm
Angle seat valve Type 2300 with
actuator sizes ø 50 mm Control unit

Type 8696

ô

 M
M

Angle seat valve

with desired control unit

Valve system
Continuous ELEMENT
Type 8802-YG-N
ô
 M 2300 + 8696
M

Click on the orange box "More info." below... you will come to our website
for the resp. product where you can download the datasheet.

TopControl Basic Type 8696 -OREô

INFO

The new generation of integrated positioners for combination with

small actuators from the process valve series Type 23xx/2103 is spe-
cially designed for the requirements of hygienic process environments.
The operation and selection of the software functions close tight func-
tion, inversion of the operating direction of the setpoint signal, charac-
teristic curves selection and switching manual/automatic operation are
effected via push-buttons and DIP switches or via the PC interface. The
position setpoint is set using the standard signal 4 - 20 mA. In addition,
the enable can be controlled via the binary input and an optional posi-
tion feedback can be integrated. The positioner, Type 8696, , registers
the valve end position without deterioration through a contact-free
analogue position sensor. Single-acting actuators are controlled via the
integral positioner system.
Main customer benefits:
• Compact design of the valve system with integrated positioner meets
the demands for plant washdown environments through the selec-
tion of materials, external seals and integrated control air supply to
the actuator
• Automatic parameterisation of the positioner using the TUNE function
• Simple and reliable actuator adaption
• Explosion-proof models for zone 2/22

p. 9/16
 2300
System Continuous
ELEMENT 8802-YG
Dimensions for valve system Continuous ELEMENT Type 8802-YG [mm]
Dimensions valve system Continuous ELEMENT Type 8802-YG-I with positioner TopControl Type 8692 or
8802-YG-J with process controller TopControl Type 8693 [mm]

Threaded body



(
×
$

37
% #
"- ,

All bodies G NPT Rc

Orifice [mm] Actuator size [mm] H BM C L SW D E D E D E
20 70 287 322 35 95 32 G 3/4 16 NPT 3/4 14 RC 3/4 14.5
25 70 295 330 35.5 105 41 G1 18 NPT 1 16.8 RC 1 16.8
32 70 301 343 41 120 50 G 1 1/4 20 NPT 1 1/4 17.3 RC 1 1/4 19.1
40 90 348 386 40 130 55 G 1 1/2 22 NPT 1 1/2 17.3 RC 1 1/2 19.1
50 90 362 405 45 150 65 G2 24 NPT 2 17.6 RC 2 23.4

Clamp body


(
×
‹$4
‹$4
34

#4
,4
"4

All clamp bodies ISO 2852 DIN 32676 BS 4825 ASME BPE
Orifice Actuator
[mm] size [mm] H BT CT LT øD1T øD2T ST øD1T øD2T ST øD1T øD2T ST øD1T øD2T ST
20 70 287 344 57 150 50.5 26.9 1.6 34 23 1.5 25.2 19.05 1.2 25 19.05 1.65
25 70 295 355 58.5 160 50.5 33.7 2 50.5 29 1.5 50.5 25.4 1.65 50.5 25.4 1.65
32 70 301 360 58 180 50.5 42.4 2 50.5 35 1.5 – – – – – –
40 90 348 416 69.5 200 64 48.3 2 50.5 41 1.5 50.5 38.1 1.65 50.5 38.1 1.65
50 90 362 438 78 230 77.5 60.3 2.6 64 53 1.5 64 50.8 1.65 64 50.8 1.65

p. 10/16
 2300
System Continuous
ELEMENT 8802-YG
Dimensions for valve system Continuous ELEMENT Type 8802-YG [mm], continued
Dimensions valve system Continuous ELEMENT Type 8802-YG-I with positioner TopControl Type 8692 or
8802-YG-J with process controller TopControl Type 8693 [mm]

Welded body



(
×
ô73
‹$3

#3
,3
"3

ISO 4200, DIN 11850 S2, ASME BPE

All bodies acc. to ISO 4200, DIN 11850 S2, ISO 4200 DIN 11850 S2 ASME BPE BS 4825
ASME BPE, BS 4825
Orifice Actuator
[mm] size [mm] H CS LS BS WS ø DS WS ø DS WS ø DS WS ø DS
20 70 287 39 115 326 1.6 26.9 1.5 23.0 1.65 19.05 1.2 19.05
25 70 295 43 130 339 2 33.7 1.5 29.0 1.65 25.4 1.65 25.4
32 70 301 40 145 342 2 42.4 1.5 35.0 – – – –
40 90 348 49 160 395 2 48.3 1.5 41.0 1.65 38.1 1.65 38.1
50 90 362 50 175 410 2.6 60.3 1.5 53.0 1.65 50.8 1.65 50.8

SMS 3008
Orifice Actuator
[mm] size [mm] H CS LS BS CS LS WS ø DS
20 70 287 39 115 339 52 145 1.2 25.0
25 70 295 43 130 347 51 152 1.2 25.0
32 70 301 40 145 342 40 145 1.2 38.0
40 90 348 49 160 406 60 182 1.2 38.0
50 90 362 50 175 424 64 210 1.2 51.0

p. 11/16
 2300
System Continuous
ELEMENT 8802-YG
Dimensions for valve system Continuous ELEMENT Type 8802-YG [mm], continued
Dimensions valve system Continuous ELEMENT Type 8802-YG-L with positioner TopControl Basic Type 8694 [mm]

Threaded body


‹

(
×
$ 37
% #
,
"-

All threaded bodies G NPT Rc

Orifice [mm] Actuator size [mm] H BM C L SW D E D E D E
20 70 259 293 35 95 32 G 3/4 16 NPT 3/4 14 RC 3/4 14.5
25 70 267 302 35.5 105 41 G1 18 NPT 1 16.8 RC 1 16.8
32 70 273 314 41 120 50 G 1 1/4 20 NPT 1 1/4 17.3 RC 1 1/4 19.1
40 90 318 357 40 130 55 G 1 1/2 22 NPT 1 1/2 17.3 RC 1 1/2 19.1
50 90 332 376 45 150 65 G2 24 NPT 2 17.6 RC 2 23.4

Clamp body

‹

(
×
‹ $4
‹$4
34

#4
,4
"4

All clamp bodies ISO 2852 DIN 32676 BS 4825 ASME BPE

Orifice Actuator
[mm] size [mm] H BT CT LT ø D1T ø D2T ST ø D1T ø D2T ST ø ø D2T ST ø ø ST
D1T D1T D2T
20 70 259 315 57 150 50.5 26.9 1.6 34 23 1.5 25.2 19.05 1.2 25 19.05 1.65
25 70 267 325 58.5 160 50.5 33.7 2 50.5 29 1.5 50.5 25.4 1.65 50.5 25.4 1.65
32 70 273 331 58 180 50.5 42.4 2 50.5 35 1.5 – – – – – –
40 90 318 386.5 69.5 200 64 48.3 2 50.5 41 1.5 50.5 38.1 1.65 50.5 38.1 1.65
50 90 332 409 78 230 77.5 60.3 2.6 64 53 1.5 64 50.8 1.65 64 50.8 1.65

p. 12/16
 2300
System Continuous
ELEMENT 8802-YG
Dimensions for valve system Continuous ELEMENT Type 8802-YG [mm], continued
Dimensions valve system Continuous ELEMENT Type 8802-YG-L with positioner TopControl Basic Type 8694 [mm]

Welded body


‹

(
×
ô73
‹$3

#3
,3
"3

ISO 4200, DIN 11850 S2, ASME BPE

All welded bodies acc. to ISO 4200, DIN 11850 S2, ISO 4200 DIN 11850 S2 ASME BPE BS 4825
ASME BPE, BS 4825
Orifice Actuator
[mm] size [mm] H CS LS BS WS ø DS WS ø DS WS ø DS WS ø DS
20 70 259 39 115 297 1.6 26.9 1.5 23.0 1.65 19.05 1.2 19.05
25 70 267 43 130 309.5 2 33.7 1.5 29.0 1.65 25.4 1.65 25.4
32 70 273 40 145 313 2 42.4 1.5 35.0 – – – –
40 90 318 49 160 366 2 48.3 1.5 41.0 1.65 38.1 1.65 38.1
50 90 332 50 175 381 2.6 60.3 1.5 53.0 1.65 50.8 1.65 50.8

SMS 3008
Orifice Actuator
[mm] size [mm] H BS CS LS WS ø DS
20 70 259 310 52 145 1.2 25.0
25 70 267 317.5 51 152 1.2 25.0
32 70 273 313 40 145 1.2 38.0
40 90 318 377 60 182 1.2 38.0
50 90 332 395 64 210 1.2 51.0

p. 13/16
 2300
System Continuous
ELEMENT 8802-YG
Dimensions for valve system Continuous ELEMENT Type 8802-YG [mm], continued
Dimensions valve system Continuous ELEMENT Type 8802-YG with control head Type 8696 [mm]

Threaded body




(
×
$ 37
% #-
,-
"-

All threaded bodies Port connection

G NPT RC
Orifice Actuator
[mm] size [mm] H BM CM SW LM D E D E D E
13 50 234 265 31 27 85 G 1/2 14 NPT 1/2 13.7 RC 1/2 13.2
262 28 32 G 3/4 16 NPT 3/4 14 RC 3/4 14.5
20 50 242 276 35 32 95 G 3/4 16 NPT 3/4 14 RC 3/4 14.5
272 31 41 G1 18 NPT 1 16.8 RC 1 16.8
25 50 250 285 35.5 41 105 G1 18 NPT 1 16.8 RC 1 16.8
281 31.5 50 G 1 1/4 20 NPT 1 1/4 17.3 RC 1 1/4 19.1

Clamp body



(
‹ $4
‹$4

34

#4
,4
"4

All clamp bodies ISO 2852 DIN 32676 BS 4825 ASME BPE

Orifice Ac-
[mm] tuator H BT CT LT ØD1T ØD2T ST ØD1T ØD2T ST ØD1T ØD2T ST ØD1T ØD2T ST
size
[mm]
13 50 234 284 49.5 130 34 21.3 1.6 34 19 1.5 25.2 12.7 1.2 25 12.7 1.65
20 50 242 298 57 150 50.5 26.9 1.6 50.5 26.9 1.6 25.2 19.05 1.2 25 19.05 1.65
25 50 250 309 58.5 160 50.5 33.7 2 50.5 33.7 2 50.5 25.4 1.65 – – –

p. 14/16
 2300
System Continuous
ELEMENT 8802-YG
Dimensions for valve system Continuous ELEMENT Type 8802-YG [mm], continued
Dimensions valve system Continuous ELEMENT Type 8802-YG with control head Type 8696 [mm]

Welded body




(
73
‹$3

#3
"3 ,3

All welded bodies EN ISO 1127/ISO 4200 DIN 11850 S2

Orifice Actuator
[mm] size [mm] H BS CS LS ø DS WS BS CS LS ø DS WS

15 50 234 268 34 100 13.5 1.6 268 34 100 19 1.5

17.2
21.3
20 50 242 280 39 115 26.9 1.6 280 39 115 23 1.5
25 50 250 293 43 130 33.7 2 293 43 130 29 1.5

All welded bodies SMS 3008 ASME BPE

Orifice Actuator
[mm] size [mm] H BS CS LS ø DS WS BS CS LS ø DS WS
15 50 234 280 46 135 12.0 1 268 34 100 12.7 1.65
20 50 242 293 52 145 18.0 1 280 39 115 19.05 1.65
25 50 250 301 51 152 25.0 1.2 293 43 130 25.4 1.65

All welded bodies BS 4825

Orifice Actuator
[mm] size [mm] H BS CS LS ø DS WS

15 50 234 268 34 100 12.7 1.2

20 50 242 280 39 115 19.05 1.2
25 50 250 293 43 130 25.4 1.65

p. 15/16
 2300
System Continuous
ELEMENT 8802-YG
Note
Valve system Continuous ELEMENT Type 8802-YG - Request for quotation fill out
You can
directly
Please fill out and send to your nearest Bürkert facility* with your inquiry or order the fields
th e P D F file
in
nting
Company Contact person before pri
rm.
out the fo
Customer no. Department

Address Tel./Fax

Postcode/town E-mail

= mandatory fields to fill out Quantity Required delivery date

Operating data
Pipe line DN PN
Pipe material
Process medium
Type of medium Liquid Steam Gas
min standard max unit
Flow rate (Q, QN, W) 1)
Temperature at valve inlet T1
Absolute pressure at valve inlet P1
Absolute pressure at valve outlet P2
Steam pressure Pv
Kinematic viscosity (ν) mm2/s or cSt
Dynamic viscosity (η) mPa.s or cP
Standard density Kg/m3
Max. sound level accepted dB (A) 1)
standard unit: Liquid Q = m3/h; Steam W = kg/h; Gas QN = Nm3/h
Type of media
Valve features Liquid Steam Gas

Plug seal material PTFE/Stainless steel Stainless steel/Stainless steel

Nominal pressure PN
Orifice DN
Type of connection Threaded Welded Clamp
Standard connection ISO DIN Other
Control function NC2) NO 2)
Please specify item no. if known:
2)
NC: normally closed by spring action; NO: normally open by spring action

Control unit features

ô ô ô
 M  M For actuator sizes 70/90 mm  M For actuator size 50 mm
M M M

Positioner -OREô Process -OREô Positioner TopControl -OREô Positioner TopControl -OREô
INFO
TopControl INFO Controller Top- INFO Basic Type 8694 Basic Type 8696 INFO

Type 8692 Control Type 8693

Pneumatic function Pneumatic function Pneumatic function
Single-acting Double-acting Single-acting Single-acting
Communication Pilot air ports Pilot air ports
Profibus DeviceNet Push-in connector external Push-in connector external
ø 6 mm or 1/4” ø 6 mm or 1/4”
Electrical connection
Thread G 1/8” Thread G 1/8”
Cable gland Multipol connection
Feedback Feedback Feedback
4-20 mA 4-20 mA + 2 binary outputs 4-20 mA 4-20 mA
Initiator
Initiator
Please specify item no. if known: Please specify item no. if known: Please specify item no. if known:

Comments

* To find your nearest Bürkert facility, click on the orange box www.burkert.com Reset form

In case of special application conditions, Subject to alteration.

please consult for advice. © Christian Bürkert GmbH & Co. KG 0909/6_EU-en_00895101

p. 16/16