Scribd
Upload
286 views1 page

At13 240

This document provides specifications for the Band III 4 dipoles horizontal polarization panel antenna, including electrical specifications like its frequency range, gain, beamwidth, and power handling. It also lists mechanical specifications such as materials, dimensions, weight, mounting details, and environmental tolerances. Tables are included that show characteristics like gain, weight, wind load, and height for antenna systems with different numbers of bays and antennas per bay.

Uploaded by

Jina Paola Alvarez Hernandez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
286 views1 page

At13 240

This document provides specifications for the Band III 4 dipoles horizontal polarization panel antenna, including electrical specifications like its frequency range, gain, beamwidth, and power handling. It also lists mechanical specifications such as materials, dimensions, weight, mounting details, and environmental tolerances. Tables are included that show characteristics like gain, weight, wind load, and height for antenna systems with different numbers of bays and antennas per bay.

Uploaded by

Jina Paola Alvarez Hernandez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

AT13-240

Band III 4 dipoles horizontal polarization panel ● Especially suitable for square masts

Electrical Specifications
Frequency range 174-230 MHz
Peak gain 10.5 dB (ref. /2 dipole)
3 dB beam width E-plane: 69º H-plane: 25º
Polarization Horizontal
Impedance 50 Ohm
VSWR 1.1:1
Maximum power handling peak sync 2 kW 3.5 kW 6 kW
Maximum power handling RMS 1.4 kW 2.5 kW 4.2 kW
Connector type DIN 7/16 EIA 7/8” DIN 13/30
Non Gas barrier on input
Pressurization
pressurized connector

TV VHF          
Mechanical & Environmental Specifications
Reflector & dipoles Hot dip galvanized steel
Materials
Feed points radome Fiberglass
Dimensions (W x D x H) 1250 x 500 x 2900 mm
Maximum wind speed 200 km/h
Wind load (front) 1590 N (@160 km/h)
Wind load (lateral) 950 N (@160 km/h)
Weight 68 Kg
Typical mounting Square arrangement tower
Clamp type To Ø 80 – 115 mm pipe
Vertical spacing 3200 mm
Grounding DC grounded E-plane
Temperature range -40°C to +80°C Horizontal
Pattern
Humidity 100%

Antenna System Characteristics


Number Wind load System
Number Peak gain Weight
ant. per (@160 height
of Bays (dBd) (kg)
bay km/h) (mm)
2 8.5 136 2.5 kN
1 3 6.7 204 3.5 kN 2900
4 5.5 272 4.3 kN
2 11.5 272 5.1 kN
2 3 9.7 408 7.0 kN 6100
H-plane
4 8.5 544 8.5 kN Vertical
Pattern
2 14.5 544 10.1 kN
4 3 12.7 816 13.9 kN 12500
4 11.5 1088 17.1 kN NOTES:
2 16.3 816 15.2 kN
- Table supplies data up to 8 bays only for
6 3 14.5 1224 20.9 kN 18900 simplification purposes; systems with more
4 13.3 1632 25.6 kN bays are available.
2 17.5 1088 20.2 kN - Null fill, beam tilt, harness & feeder losses
NOT INCLUDED.
8 3 15.7 1632 27.8 kN 25300 - Wind load & weight figures without
4 14.5 2176 34.2 kN considering cables, splitters & hardware.

E-mail: [email protected]
RYMSA RF will reserve the right to make any changes without notice. Web: www.rymsarf.com

You might also like