SHEETPILE WALL Job #: Date: 4/1/2015

Soil Data:
Soil Type Silty SAND
Active Soil Frict. Angle 31.0 0.5411 0.54 Radians
Wet Unit. Wt. gm 115.0 pcf 18.07 kN/m3
Surcharge= (Ka*q)=Ps 16.00 psf 0.77 KPa
Act. Coeff Ka 0.320 0.32
Pass. Coef Kp 3.124 3.12
Eq. Active Fluid Press. 36.8 psf/ft 0.54 KPa/m
Eq. Pass. Fluid Press. 359.3 psf/ft 5.24 KPa/m
Mom.of Inertia, I 84.38 in^4 3512.16 cm4
Elastic Modulus, E 29000 ksi 22105.24 KPa

GWT, Hw 12.50 ft 0 to H 3.81 m

Surcharge 50 psf (qs) ` 2.39 KPa

Bkfl Slope 0 Deg. 0.0000 0.0000
Radians

Passive Soils Frict. Angle 31.0 0.5411 0.5411

Descrip: Silty SAND Degree Radians

REFERENCES

1. Foundation Engineering, 1986, A.R. Jumikis. Krieger Publishing

2. Modern Formulas for Statics and Dynamics, A Stress-and-Strain Approach, 1978
by Pilkey & Chang, McGraw Hill
3. Skyline (ArcelorMittal) Steel Sheetpile Technical Product Manual
4. Alex Tomanovich's BEAMANAL Program

RESULTS

Sigma bott. lateral active press. @ b.o.e. 460.14 psf 22.03

h/3 Active earth pressure moment arm 4.17 ft 1.27
m Depth to zero pressure height 1.43 ft 0.43
P1 Active earth press. thrust @h/3 2875.89 lb/ft 3.90
P2 Active earth press. thrust below b.o.e. 328.31 lb/ft 0.45
t Height of passive resistance 10.00 ft 3.05
y1 h/3 + m + t 15.59 ft 4.75
y2 0.667m + t 10.95 ft 3.34
Yr t/3 3.33 ft 1.02
Pr Passive resistance 3224.52 psf 154.39
dmin Theoretical Depth 11.43 ft 3.48
1.3(dmin) Required Embedment (D) 14.86 ft 4.53
Mmax Maximum Moment 27.78 k-ft 0.04
Loc. Max. Mom. Loc. from b.o.e. 5.55 ft 1.69
Req. Sx Required Section Modulus 11.11 in^3 182.07
Prov. Sx Provided Section Modulus 18.10 in^3 296.61

Note: b.o.e. = bottom of excavation

 Design By: LAA
Geometry / Sheeting In this worksheet,
Sheeting PZ 22 Only enter
Shored Ht,h 12.50 ft 3.81 m Input Cells
Yield Strength 50.0 ksi 2081.2 KPa
Allow. Stress 30.0 ksi 1248.7 KPa Computed Cells

Loading Diagram

Active Soils

Passive Soils

kPa
m
m
kN/m
kN/m
m
m
m
m
kPa
m
m
kN.m
m
cm3
cm3 O.K.
In this worksheet,
Yellow Cells

Active Soils GWT, Hw

 "BEAMANAL.xls" Program
Version 2.5

CANTILEVER SHEETPILE ANALYSIS using Tomanovich's BEAMANAL

Blum's Cantilever Sheetpile Method
For Full Uniform Load, w
Project Name: Location: Loading Functions Evaluated a
Job Number: Design By: Check By: Points:
###
Input Data: c ###
e ###
Sheeting Data: b ###
Boundary? Cantilever keep it at Cantilever a ###
Length, L = 27.36 ft. +P +M +we ###
Modulus, E = 29000 ksi +wb ###
Inertia, I = 84.38 in.^4 +w ###
E,I L ###
Loadings: Cantilever Sheetpile RL x RR ###
Full Uniform: Nomenclature ###
w= 0.0000 kips/ft. ###
Start End Results: ###
Distributed: b (ft.) wb (kips/ft.) e (ft.) we (kips/ft.) Reactions:
Active Pres. Top 0.0000 0.0000 12.5000 0.460 RL = N.A. RR = -14.56 k ###
Passive Resist. 13.9270 0.0000 23.9270 -3.593 ML = N.A. MR = 57.81 ft-k ###
Pore Water Pres. 12.5000 0.0000 12.5000 0.000 Maximum Moments: ###
Uniform Surch. 0.0000 0.016 12.5000 0.016 +M(max) = 57.81 ft-k @x= 27.36 ft. ###
Active. Pres. Bot. 12.5000 0.4601 13.9270 0.000 -M(max) = -27.78 ft-k @x= 18.05 ft. ###
Maximum Deflections: ###
-D(max) = -0.987 in. @x= 0.00 ft. ###
+D(max) = 0.500 in. @x= 17.51 ft. ###
D(ratio) = L/333 ###
Point Loads: a (ft.) P (kips) ###
#1: Shear Diagram ###
Shear (kips)

20.00
#2: ###
#3: ###
15.00
#4: ###
#5: ###
#6: 10.00 ###
#7: ###
#8: 5.00 ###
#9: ###
#10: 0.00
###
#11: ###
3.2826
4.3768
5.4710

8.7536
9.8478
10.9420
12.0362

17.5073
18.6015

22.9783
24.0725
0.0000
1.0942
2.1884

6.5652
7.6594

13.1305
14.2247
15.3189
16.4131

19.6957
20.7899
21.8841

25.1667
26.2609
27.3551

#12: x (ft.) ###

M o m e n t ( f t - k ip s )

-5.00
#13: ###
#14: ###
#15: ###
###
Moments: c (ft.) M (ft-kips) 80.00 Moment Diagram
###
60.00
#1: ###
40.00
#2: ###
20.00
#3: ###
0.00
12.0362

15.3189

17.5073

20.7899

22.9783

25.1667
10.9420

13.1305
14.2247

16.4131

18.6015
19.6957

21.8841

24.0725

26.2609
27.3551
0.0000
1.0942

3.2826

6.5652

8.7536
2.1884

4.3768
5.4710

7.6594

9.8478

#4: -20.00
###
-40.00
###
x (ft.)
###

6 of 6 05/12/2018 09:07:55