XR-3100R/C33R

SERVICE MANUAL AEP Model

UK Model

Photo: XR-C33R

Model Name Using Similar Mechanism XR-C5100R

Tape Transport Mechanism Type MG-25G-136

SPECIFICATIONS

FM/MW/LW CASSETTE CAR STEREO

MICROFILM

Downloaded from www.Manualslib.com manuals search engine

 TABLE OF CONTENTS Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
1. GENERAL ing repairing.
Location of controls ........................................................ 3 • Do not touch the soldering iron on the same conductor of the
Resetteing the unit ........................................................... 4 circuit board (within 3 times).
Detaching the front panel ................................................ 4 • Be careful not to apply force on the conductor when soldering
Setting the clock .............................................................. 4 or unsoldering.
Installation ....................................................................... 5
Connections ..................................................................... 6 Notes on chip component replacement
• Never reuse a disconnected chip component.
2. DISASSEMBLY ......................................................... 10 • Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
3. ASSEMBLY OF MECHANISM DECK ........... 11

4. MECHANICAL ADJUSTMENTS ....................... 14

5. ELECTRICAL ADJUSTMENTS ......................... 14

6. DIAGRAMS

6-1. Block Diagram – TUNER Section – .............................. 18

6-2. Block Diagram – TAPE/MAIN Section – ...................... 19
6-3. Block Diagram – DISPLAY/KEY CONTROL/
BUS CONTROL/POWER SUPPLY Section – .............. 20
6-4. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 21
6-5. Printed Wiring Board
– MAIN Board (Component Side) – .............................. 22
6-6. Printed Wiring Board
– MAIN Board (Conductor Side) – ................................ 23
6-7. Schematic Diagram – MAIN Board (1/3) – ................... 24
6-8. Schematic Diagram – MAIN Board (2/3) – ................... 25
6-9. Schematic Diagram – MAIN Board (3/3) – ................... 26
6-10. Printed Wiring Board – KEY Board – ........................... 30
6-11. Schematic Diagram – KEY Board – ............................. 31
6-12. IC Pin Function Description ........................................... 32

7. EXPLODED VIEWS ................................................ 35

8. ELECTRICAL PARTS LIST ............................... 38

2
Downloaded from www.Manualslib.com manuals search engine
 SECTION 1 This section is extracted from
GENERAL instruction manual.

3
Downloaded from www.Manualslib.com manuals search engine
 4
Downloaded from www.Manualslib.com manuals search engine
 5
Downloaded from www.Manualslib.com manuals search engine
 6
Downloaded from www.Manualslib.com manuals search engine
 (XR-3100R)

7
Downloaded from www.Manualslib.com manuals search engine
 (XR-C33R)

8
Downloaded from www.Manualslib.com manuals search engine
 9
Downloaded from www.Manualslib.com manuals search engine
 SECTION 2
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.

SUB PANEL, MECHANISM DECK (MG-25G-136)

5 screw
(PTT2.6 × 6)
3 connector
(CN302)

6 mechanism deck
(MG-25G-136)

4 flexible flat cable

(CN301)

2 sub panel

1 three screws
(PTT2.6 × 8)

1 three screws
(PTT2.6 × 8)

MAIN BOARD, HEAT SINK

5 screw 5 two screws
(PTT2.6 × 8) (C33R) (PTT2.6 × 8)
1 screw
(PTT2.6 × 8)
7 heat sink
6 three screws
(PTT2.6 × 12)
3 two ground point 5 screw
screws (PTT2.6 × 8) (C33R)

5 screw
(PTT2.6 × 8)

4 main board
2 rubber cap (25)

1 two screws
(PTT2.6 × 8)

10
Downloaded from www.Manualslib.com manuals search engine
 SECTION 3
ASSEMBLY OF MECHANISM DECK
Note: Follow the assembly procedure in the numerical order given.

HOUSING
7 Holder the hanger by bending the claw.
5 Fit projection on C part.
1 Install the catch to the hanger.
2 Install the hanger onto
two claws of the housing.
hanger
4 Fit claw on B part.

3 Put the housing

6 Fit projection on D part.
under A part.

housing

C part
8 Hold the hanger by
bending the claw.

D part

A part

B part

ARM (SUCTION)
2 Move the arm (suction) in the arrow
direction and fit on projection.

projection
1 Fit the arm (suction) on the shaft.

11
Downloaded from www.Manualslib.com manuals search engine
 LEVER (LDG-A) / (LDG-B)

shaft A
shaft A
shaft B
shaft B
shaft C

1 Fit the lever (LDG-A) on

shafts A – C and install it. 3 type-E stop ring 2.0

2 Fit the lever (LDG-B) on

shafts A and B and
install it.

GEAR (LDG-FT)

gear (LDG-D)
6 polyethylene washer
hole
5 gear (LDG-FT)

hole lever (LDG-A)

gear (LDG-FB)

4 Align hole in the gear (LDG-D)

with hole the lever (LDG-A).

2 tension spring (LD-2)

3 Move the lever (LDG-B)

2 tension spring (LD-1) in the arrow direction.

12
Downloaded from www.Manualslib.com manuals search engine
 GUIDE (C)

2 guide (C)

1 three claws

MOUNTING POSITION OF CAPSTAN/REEL MOTOR (M901)

two precision screws

(P2 × 2)

capstan/reel motor
(M901)

30˚

13
Downloaded from www.Manualslib.com manuals search engine
 SECTION 4 SECTION 5
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
1. Clean the following parts with a denatured-alcohol-moistened TEST MODE
swab: This set have the test mode function. In the test mode, FM Auto
playback head pinch roller Scan/Stop Level and MW Auto Scan/Stop Level adjustments can
rubber belt capstan be performed easier than it in ordinary procedure.
idler
2. Demagnetize the playback head with a head demagnetizer. <Set the Test Mode>
3. Do not use a magnetized screwdriver for the adjustments. 1. Set the “power select” switch (S501) is “A (ON)” position.
4. After the adjustments, apply suitable locking compound to the 2. Turn ON the regulated power supply. (All LEDs on the set
parts adjusted. lights up, and the clock is displayed.)
5. The adjustments should be performed with the power supply Note: Press the [OFF] button, if the clock is not displayed.
voltage unless otherwise noted. 3. Push the preset [4] button.
4. Push the preset [5] button.
• Torque Measurement 5. Press the preset [1] button for more than two seconds.
6. Then the display indicates all lights, the test mode is set.
Mode Torque Meter Meter Reading
30 – 65 g•cm <Release the Test mode>
Forward CQ-102C
(0.42 – 0.90 oz•inch)
1. Push the [OFF] button.
Forward 0.5 – 4.5g•cm 2. Return the “power select” switch (S501) to initially set posi-
CQ-102C
Back Tension (0.01 – 0.06 oz•inch)
tion.
30 – 65 g•cm
Reverse CQ-102RC
(0.42 – 0.90 oz•inch)
Reverse 0.5 – 4.5g•cm See the adjustment location from on page 17 for the
CQ-102RC
Back Tension (0.01 – 0.06 oz•inch) adjustment.
60 – 200 g•cm
FF, REW CQ-201B
(0.83 – 2.78 oz•inch)
TAPE DECK SECTION 0 dB=0.775 V
• Tape Tension Measurement
Mode Tension Meter Meter Reading Tape Speed Adjustment
more than 90 g Setting:
Forward CQ-403A
(more than 3.18 oz) speed checker
more than 90 g or
Reverse CQ-403R frequency counter
(more than 3.18 oz) test tape
WS-48A
(3 kHz, 0 dB) 10 k Ω

set
– +
AUDIO OUT jack (CNJ151)

Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
reading on the speed checker or frequency counter becomes in
specification.

Specification: Constant speed

Speed checker Frequency counter
–1.5 to +2.5% 2,955 to 3,075 Hz

Adjustment Location: See page 17.

14
Downloaded from www.Manualslib.com manuals search engine
 FM Stereo Separation Adjustment
TUNER SECTION 0 dB=1 µV
Setting:
Cautions during repair
[SOURCE] button: FM
When the tuner unit is defective, replace it by a new one be- FM RF signal
cause its internal block is difficult to repair. generator antenna jack (J1) level meter

Note: 0.01 µF 10 k Ω
Adjust the tuner section in the sequence shown below. +
set –
1. FM Auto Scan/Stop Level Adjustment
2. FM Stereo Separation Adjustment Carrier frequency : 98.0 MHz
3. FM RDS S-Meter Adjustment Output level : 70 dB (3.2 mV) AUDIO OUT jack (CNJ151)
4. MW Auto Scan/Stop Level Adjustment Mode : stereo
Modulation : main: 1 kHz, 20 kHz deviation (26.7%)
sub: 1 kHz, 20 kHz deviation (26.7%)
FM Auto Scan/Stop Level Adjustment : 19 kHz pilot: 7.5 kHz deviation (10%)
Setting:
[SOURCE] button: FM Procedure:
FM Stereo
FM RF signal signal generator Level meter Level meter
generator antenna jack (J1) connection reading (dB)
output channel
0.01 µF L-CH L-CH A
set B
R-CH L-CH Adjust RV4 on TU1
Carrier frequency : 98.0 MHz for minimum reading.
Output level : 22 dB (12.6 µV)
Mode : mono R-CH R-CH C
Modulation : 1 kHz, 22.5 kHz deviation (30%) D
L-CH R-CH Adjust RV4 on TU1
Procedure: for minimum reading.
1. Set to the test mode. (See page 14)
2. Push the [SOURCE] button and set to FM. L-CH Stereo separation: A-B
Display R-CH Stereo separation: C-D
The separations of both channels should be equal.

SHUF Specification: Separation more than 30 dB

Adjustment Location: See page 17.

3. Adjust with the volume RV2 on TU1 so that the “FM” indica-
tion turns to “FM0” indication on the display window.
But, in case of already indicated “FM0”, turn the RV2 so that
put out light “0” indication and adjustment.

Display

SHUF

Adjustment Location: See page 17.

15
Downloaded from www.Manualslib.com manuals search engine
 FM RDS S-Meter Adjustment MW Auto Scan/Stop Level Adjustment
Setting: Make this adjustment after “FM Auto Scan/Stop Level Adjust-
[SOURCE] button: FM ment”.
Setting:
FM RF signal [SOURCE] button: MW
generator
antenna jack (J1)
0.01 µF 30 Ω 15 pF
set
65 pF
Carrier frequency : 98.00 MHz
Output level : 35 dB (56.2 µV)
Mode : mono AM RF signal
Modulation : no modulation generator
AM dummy antenna
Procedure: (50 Ω)
1. Set to the test mode. (See page 14) set
2. Push the [SOURCE] button and set to FM.
Carrier frequency : 999 kHz antenna jack (J1)
Display 30% amplitude
modulation by
1 kHz signal
Output level : 33 dB (44.7 µV)
SHUF
Procedure:
1. Set to the test mode. (See page 14)
3. Push the [6] button. 2. Push the [SOURCE] button and set to FM.
4. Adjust RV1 on main board so that the display indication is 3. Push the [MODE] button and set to MW.
“10.8”.
Display Display

SHUF TP SHUF

Specification: Display indication: 10.6 to 11.0 4. Adjust with the volume RV1 on TU1 so that the “MW” indi-
cation turns to “MW0” indication on the display window.
Adjustment Location: See page 17. But, in case of already indicated “MW0”, turn the RV1 so that
put out light “0” indication and adjustment.

Display

TP SHUF

Adjustment Location: See page 17.

16
Downloaded from www.Manualslib.com manuals search engine
 Adjustment Location:

– SET UPPER VIEW –

Tape Speed Adjustment

TU1

RV1 MW Auto Scan/Stop Level Adjustment

RV2 FM Auto Scan/Stop Level Adjustment

RV4 FM Stereo Separation Adjustment

RV1 FM RDS S-Meter Adjustment

17 17

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R
SECTION 6
DIAGRAMS
6-1. BLOCK DIAGRAM – TUNER Section –

D1

FM B+
AM B+

FM/AM TUNER UNIT

TU1
J1 9 8 10
(FM/AM ANTENNA)
+8V-AM
+8V-TU

+8V-FM

FM-L
2 FM-ANT LCH-OUT 17 A (Page 19)

1 AM-ANT RCH-OUT 15 R-CH MUTING

IF-COUNT/SEEK

Q151
AM-XTAL-IN

S-METER

AM-DET
FM-DET
LO/DX

R-CH
SEEK
VCO

SD
ST
VT

4 5 6 20 13 11 19 21 18 22 12

AM
B (Page 19)

MUTING
Q121

MUTING
CONTROL SWITCH
BUFFER Q61
Q51 D61

FILTER

11 18 20 19 15 16 13 10 2
RDS DECODER
FM-CPOUT

AM-CPOUT
LO/DX

FM-VCO

AM-VCO

IF IN

SEEK

OSC OUT
VT

IC51 SIGNAL 5
QUALITY
DECODER 4
XTOUT, XTIN

SC
57 kHz
1, 24

FM/AM PLL X1 OUT CIN RDS/RDBS

CLOCKED INTERFACE
IC1 10.25MHz 16 BAND-PASS 18 19 DEMODULATOR
MPX COMPARATOR REGISTER
FILTER & DECODER
MPTH
DOUT

LVIN MULTI OSCILLATOR IIC BUS

DIN
CK
CE

20 PATH 2 & CLOCK SLAVE

DETECTOR TRANSCEIVER
6 4 5 3
OSCO

DAVN
OSCI

SDA

SCL
5 4 8 9 10

BAND-PASS X51
RV1 FILTER 4.332MHz
CLOCK
DATA

IC90
FM RDS
S-METER
Q90 DATA, CLOCK
NOISE DET C (Page 19)
DISCHARGE
SWITCH

25 26 27 28 1 20 4 53 50 32 52 75 5
DAVN
PLLSI

SEEKOUT
SD-IN
ST-MONO

VSM

NOISE DET

NOISE ON

TUNMUTE
PLLSO
PLLCKO
PLLCE

MTP

SYSTEM CONTROLLER
IC501 (1/3)
• SIGNAL PATH
: FM

05
: AM (MW/LW)

18 18

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R

6-2. BLOCK DIAGRAM – TAPE/MAIN Section –

CNJ151 (1/2)
BUS
AUDIO IN
INPUT SELECT, (C33R)
L ELECTRICAL VOLUME CNJ151 (2/2)
IC401
L
R R-CH
AUDIO OUT
(C33R) LOUDNESS VOLUME TONE (LINE OUT)
PDL SOFT OUT FL
11 CONTROL CONTROL CONTROL FADER 22
MUTE

SELECTOR
FM-L SE1L CIRCUIT CIRCUIT CIRCUIT R-CH R
(Page 18) A 1

INPUT
SE3L
28
SE2L LOUDNESS OUT RL
12 CONTROL FADER 20
CIRCUIT POWER AMP CN601 (1/2)
AM
(Page 18) B R-CH IC611 (POWER CONNECTOR)

11
FL+ 17 FRONT L (+)
15 FL-IN 10
DIGITAL CONTROL FL– 19 FRONT L (–)
IIC BUS MUTING
TAPE EQUALIZER AMP, AMS CIRCUIT
HP901 IC301 Q171 + 12
(PLAYBACK) FR+ 9 FRONT R (+)

MUTE
PBF R-CH 11 FR-IN
SDA
SCL
PB TAPE LINE 13
FWD IN1 FR– 7 FRONT R (–)
34 OUT1 IN1 DOLBY OUT1 MUTING
L-CH EQ AMP 29 27 MUTE 24 25 24 26
NR AMP Q271 9
RL+ 21 REAR L (+)
FWD 14 RL-IN 8
R-CH RL– 23 REAR L (–)
R-CH R-CH R-CH MUTING
R-CH R-CH MS Q181 + 15
AMS OUT 5 REAR R (+)
REV
R-CH + DET
14 RR+
32 R-CH 12 RR-IN 14
L-CH PBR RR– 3 REAR R (–)
IN1 MUTING
Q281
TAPESW

DOLBY

MSSW
DRSW

ST-BY
REV

MUTE
INSW

R-CH
R-CH D621
D622 MUTING
19 18 17 16 20 BATT B+ CONTROL SWITCH 22 4
Q621

MUTING
CONTROL SWITCH
DATA, CLOCK DATA Q622
(Page 18) C D624
CLOCK

BATT B+

113 115 117 114 103 70 71 60 65

N-ROUT

MTLON

TAPE MUTE

AMSON

AMSIN

I2C SIO
I2C CKO

MUTE
EVOL MUTE

BEEP 15

AMP MUTE 68
SYSTEM CONTROLLER
AMP ON 118
IC501 (2/3)
LM-LOD

TAPEON

CM-ON
LM-EJ

REEL

POS0 – POS3
110 109 112 111 105 – 108 104

REGULATOR
REEL SENSOR B+ BATT B+
Q361

TAPE OPERATION BUFFER

REGULATOR SWITCH
3 CONTROL SWITCH
VCC Q362
OUT1 IN1 EJECT/FF/REW/ TAKE-UP SUPPLY
LOADING/TAPE 7 MOTOR 4 REV/FWD MODE DETECT REEL REEL
OPERATION
M OUT2 DRIVE IN2
SENSOR SENSOR
9 2
TAPE
DETECT

LOADING/TAPE OPERATION • SIGNAL PATH

REEL SENSOR BOARD
MOTOR DRIVE
IC361
: FM
: AM (MW/LW)
: TAPE PLAY

M901
CAPSTAN/REEL : BUS AUDIO IN
(CAPSTAN/REEL)
M MOTOR DRIVE BATT B+
Q364

Q365

05 19 19

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R
6-3. BLOCK DIAGRAM – DISPLAY/KEY CONTROL/BUS CONTROL/POWER SUPPLY Section –

SYSTEM CONTROLLER LIQUID CRYSTAL DISPLAY DRIVER CN701

SONY BUS INTERFACE
IC501 (3/3) IC901 IC701 BUS CONTROL IN
J501 ILL B+ (FOR SONY BUS)
REMOTE IN
RST RST RST 2
RESET
72 RC-IN1 LCD SO 13 64 DI OSC 60 13 2 RESET
SWITCH
LCD CKO 14 63 CL
48 RC-IN0 LCD CE 16 62 CE
DATA-OUT DATA IN DATA 5
9 6 DATA
D653 LSW901 – 903, 905, 906,
LED DRIVE DATA-IN DATA OUT
LSW901 – 903, 905, SHIFT 3 LSW921 – 923, 8
Q945
LSW906, 921 – 923, LSW925 – 933
LSW925 – 933, S901 46 KEYIN0 CLK CLK IN CLK 4
11 4 CLK
S04 – S47

47 KEYIN1
4 – 47

BUS BUS ON
BUS ON ON IN OUT 6
BUS ON
12 1 BUS ON
LIQUID CRYSTAL SWITCH
D501 DISPLAY
COM1 – COM4

LCD901
BU-IN BU IN BATT 7
52 – 55

BATTERY
RE901 10 3 BATT
SWITCH
VOLUME/BASS/TREBLE/
BALANCE/FADER CONTROL

ENCODE –
ROTARY 36 RE-IN0
ENCODER ENCODE + D702 TH701
RE901 37 RE-IN1
(C33R)

D701
BATTERY DETECT
BATT B+
Q701
BACKUP +5V
D707
RST BATTERY DETECT
KEY ACTIVE SYSRST 11
DATA-OUT Q701 – 703
SWITCH UNISO 18
Q651, 652 DATA-IN (3100R)
UNISI 17
CLK CN601 (2/2)
UNICKO 19 (POWER CONNECTOR)
35 AD-ON BUS ON
BUS-ON 10
BU-IN D673 2
76 KEYACK BU-IN 77
ANT REM
7
AMP REM
S981
D674
D-BASS
(C33R)

6 AMP+B
51 D-BASS +5V BATT B+
+5V
REGULATOR 8 ANT+B POWER AMP
(TUNER CIRCUIT B+)
Q71 (IC611) B+

FM B+ 11 FM8V
FM/AM TUNER UNIT REGULATOR
(TU1) B+ IC671 VCC 7
4 4 AM B+ 10 AM8V
12 DOORSW
COM +8V
15 15 9 COM8V
(AUDIO CIRCUIT B+)
80 NOSESW
MODE1
MODE2

BACKUP +5V 5 BU+B

STB

CNP901 CN500 D651

(FRONT PANEL SIDE) (MAIN BODY SIDE)
3 2 4

FM-ON 6
TU-ON 7
POWON 120
RESET SIGNAL
BACKUP +5V GENERATOR 90 RESET
+9V
IC652 +9V
86 HSTX REGULATOR
(TUNER CIRCUIT B+)
Q81
S503
(RESET) REGULATOR
CONTROL SWITCH
Q82

PL901, 902
(LCD BACK LIGHT)
S501
+10V 1
POWER SELECT
ILL B+ REGULATOR BATT
A (ON) Q631
56 POWSEL
REGULATOR
ILL-ON 29 CONTROL SWITCH
B (OFF) Q633 D662 5
ACCESSORY CHECK
ACC IN 81 ACC
Q661
X1A

X0A

X1

X0

05 73 74 93 92

X502 X501
32.768kHz 3.68MHz

20 20

Downloaded from www.Manualslib.com manuals search engine

 6-4. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

Note on Printed Wiring Board: Note on Schematic Diagram:

• X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. pF: µµF
• Y : parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics
• b : Pattern from the side which enables seeing. and tantalums.
(The other layers' patterns are not indicated.) • All resistors are in Ω and 1/4 W or less unless otherwise
specified.
Caution: • f : internal component.
Pattern face side: Parts on the pattern face side seen from • C : panel designation.
(Conductor Side) the pattern face are indicated. • U : B+ Line.
Parts face side: Parts on the parts face side seen from • H : adjustment for repair.
(Component Side) the parts face are indicated. • Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : MW(LW)
〈〈 〉〉 : TAPE PLAYBACK
∗ : Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : MW(LW)
L : BUS AUDIO IN
E : TAPE PLAYBACK
• Abbreviation
AMBER : Amber illumination type
GREEN : Green illumination type

21 21

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R
6-5. PRINTED WIRING BOARD – MAIN Board (Component Side) –

• Semiconductor Location
Ref. No. Location Ref. No. Location
D1 F-14 D702 E-3
D61 G-9 D703 F-3
D71 D-11 D704 C-3
D81 E-3 D705 B-3
D90 K-10 D706 B-3
D91 K-9 D707 F-2
D92 K-9
D93 K-9 IC1 E-12
D361 H-3 IC51 I-11
D441 A-12 IC90 J-10
D481 A-11 IC301 G-11
D501 H-8 IC361 I-2
D551 K-13 IC401 E-9
D552 K-13 IC501 H-6
D553 J-11 IC652 G-2
D554 K-12 IC701 F-3
D555 J-11
D556 J-12 Q51 J-13
D557 J-11 Q61 G-9
D558 J-11 Q71 D-11
D559 J-11 Q81 E-3
D561 K-13 Q82 E-2
D562 K-13 Q90 K-9
D602 B-4 Q121 F-8
D603 B-5 Q151 F-8
D604 H-10 Q171 C-10
D611 C-6 Q181 C-11
D612 C-7 Q251 F-9
D613 C-6 Q271 C-9
D614 C-6 Q281 C-10
D615 B-7 Q361 I-3
D616 B-8 Q362 I-2
D617 B-8 Q364 G-3
D618 B-8 Q365 H-3
D621 D-9 Q621 D-8
D622 E-8 Q622 E-7
D623 E-7 Q633 J-2
D624 E-7 Q651 J-8
D631 J-2 Q652 J-8
D653 I-8 Q661 C-5
D661 D-5 Q701 F-3
D662 C-5 Q702 F-2
D701 F-2 Q703 F-2

22 22

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R
6-6. PRINTED WIRING BOARD – MAIN Board (Conductor Side) –

• Semiconductor
Location
Ref. No. Location
D362 H-2
D601 C-1
D651 F-2
D671 C-4
D672 E-2
D673 E-2
D674 D-4

IC611 A-9
IC671 E-2

Q631 J-2

(Page 30)
23 23

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R
6-7. SCHEMATIC DIAGRAM – MAIN Board (1/3) – • See page 29 for Waveforms. • See page 27 for IC Block Diagrams.

(Page 26)

(Page 25)

(Page 26)

24 24

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R
6-8. SCHEMATIC DIAGRAM – MAIN Board (2/3) – • See page 29 for Waveforms.

(Page
24)

(Page 26)

25 25

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R
6-9. SCHEMATIC DIAGRAM – MAIN Board (3/3) – • See page 28 for IC Block Diagrams.

(Page
24)

(Page 31)

(Page
25)

(Page
24)

26 26

Downloaded from www.Manualslib.com manuals search engine

 • IC Block Diagrams
– MAIN Board –
IC1 TB2118F-EL-S

AM CP OUT

FM CP OUT
A-GND

D-GND

AM IN
FM IN
VDD
REG
VCC

IFC
VT
XI

24 23 22 21 20 19 18 17 16 15 14 13

+ AMP
VDD
VCC
– + – +
AMP

AMP
4BIT SWALLOW
REGULATOR COUNTER

SEEK/RECP SEEK/RECP
PRESCALLER +

SIG 12BIT
PHASE
PROGRAMMABLE
COMPARATOR
COUNTER
20BIT
REF

IF COUNTER
40BIT SHIFT
REFERENCE REGISTER
OSCILLATOR DIVIDER
18BIT
22BIT

ON/OFF 18BIT

BUFFER VDD2

SERIAL I/O OUTPUT

INTERFACE PORT PORT

1 2 3 4 5 6 7 8 9 10 11 12
I/O-1
CK
XO

SR

I/O-2
DOUT

OUT-1
OUT-2

VDD2
CE
DIN
OSC

IC51 SAA6588T/V2-118
SCOUT

PSWN
VDDA
VSSA
VREF

MAD
LVIN

AFIN
MPX
CIN

20 19 18 17 16 15 14 13 12 11

POWER SUPPLY PAUSE

MULTI & RESET DETECTOR
PATH 57kHz
DETECTOR 8th ORDER
BAND-PASS FILTER

CLOCKED SIGNAL QUALITY

COMPARATOR DECODER

4 5
4
CLOCK CLOCK
RDS/RDBS RDS/RDBS INTERFACE
DEMODULATOR DECODER REGISTER DATA

DATA

TEST OSCILLATOR IIC BUS SLAVE

CONTROL & CLOCK TRANSCEIVER

1 2 3 4 5 6 7 8 9 10
SDA
OSCI

VSSD

DAVN

SCL
MPTH

OSCO

VDDD
MRO

TCON

27
Downloaded from www.Manualslib.com manuals search engine
 IC301 CXA2509AQ-T4 IC361 LB1638M

LINEOUT2
TAPEIN2
PBOUT2

AUXIN2
PBEQ2

MSSW
DIREF
GND 1 10 N.C.

GND

NC
NC
30 29 28 27 26 25 24 23 22 21

CONTROL LOGIC
24dB IN1 2 9 OUT1
120µ/70µ
T2
+ –
8 VS
20 MSMODE
– + VCC 3
NR BIAS MS 7 OUT2
PBFB2 31 19 DRSW
X1 MODE IN2 4
PBRIN2 32
TAPE/AUX
18 TAPESW
PBREF2 33 F2
17 INSW GND 5 6 N.C.
TAPE EQ
PBFIN2 34
16 NC
FWD/RVS
VCT 35
VCT
PBGND 36 VCC MS ON/ 15 NC
OFF
+ LPF +
DETECT
–
PBFIN1 37 14 MSOUT
F3
PBREF1 38 F1
X1 13 DGND
PBRIN1 39
PBFB1 40 12 MSTC
+ –
– + 11 G1FB
T1

120µ/70µ 24dB

1 2 3 4 5 6 7 8 9 10
PBEQ1

PBOUT1

VCC
TAPEIN1
AUXIN1

MSLPF

LINEOUT1

NC

NC

G2FB

IC401 TDA7462D013TR

28 SE3L
27 SE3R
26 MUTE
25 SDA
24 SCL
PAUSE
23 PAUSE
DETECT

INPUT TREBLE/ FRONT

LOUDNESS VOLUME VOICE BANDPASS 22 OUT FL
GAIN & SOFT BASS FADER
FRONT SIDE

CONTROL
SELECTOR

SE1L 1 CONTROL MUTE

AUTO CONTROL HP LP
SE1R 2 CIRCUIT CIRCUIT
ZERO CIRCUIT
MD+ 3
INPUT MULTIPLEXER &

FRONT
MD– 4 21 OUT FR
FADER
MIXING STAGE

CDL+ 5
CDL– 6
CDR– 7 COMPANDER
CDR+ 8
PDR 9 REAR
REAR SIDE
SELECTOR

20 OUT RL
PDGND 10 FADER
PDL 11
SE2L 12 LOUDNESS
INPUT
SE2R 13 CONTROL REAR
GAIN 19 OUT RR
CIRCUIT FADER

SUBWOOFER FADER
BEEP LP

SUBWOOFER 18 SUBOUT+
OUT 17 SUBOUT–
SDA
IIC
DIGITAL CONTROL CIRCUIT SCL
BUS

POWER 16 VDD
CREF 14
SUPPLY 15 GND

28
Downloaded from www.Manualslib.com manuals search engine
 IC671 BA3918-V3 • Waveforms
– MAIN Board – – KEY Board –

1 IC1 2 (OSC OUT) 1 IC901 y; OSC

REGULATOR

0.8 Vp-p 2.7 Vp-p

OVER VOLTAGE
PROTECT

– – – –
+ + + +
98 ns 27 µs

2 IC51 5 (OSCI)
1 2 3 4 5 6 7 8 9 10 11 12
NC
MODE2
MODE1
STB

VDD
AMP

VCC

ANT
COM

AM

FM

GND

3.3 Vp-p

IC701 BA8270F-E2

231 ns
BUS ON 1 BUS ON 14 VCC
SWITCH

RESET
3 IC501 uf (X0A)
RST 2 13 RST
SWITCH
12 BUS ON
11 CLK IN
BATTERY
BATT 3 10 BU IN
SWITCH

CLK 4 3.6 Vp-p

VREF 5
DATA 6 9 DATA IN

GND 7 8 DATA OUT

30.5 µs

4 IC501 od (X1)

5.8 Vp-p

272 ns

29 29

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R

6-10. PRINTED WIRING BOARD – KEY Board –

• Semiconductor
Location
Ref. No. Location
D951 C-9

(Page 23)
• Semiconductor
Location
Ref. No. Location
D902 C-12
D903 B-12
D904 B-11

IC901 C-8

Q945 C-2

30 30

Downloaded from www.Manualslib.com manuals search engine

 XR-3100R/C33R

6-11. SCHEMATIC DIAGRAM – KEY Board – • See page 29 for Waveform.

(Page 26)

31 31

Downloaded from www.Manualslib.com manuals search engine

 6-12. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 MB90574PMT-G-222-BND (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
Seek control signal output to the FM/AM tuner unit (TU1) 36 RE-IN0 I Dial pulse input of the rotary encoder (RE901)
AM mode: Used for IF count output/SD output request/AGC cut at SEEK or BTM 37 RE-IN1 I (for VOLUME/BASS/TREBLE/BALANCE/FADER control)
1 SEEKOUT O
FM mode: Used for SD speed up at SEEK, BTM, or AF
38 DVCC — Power supply terminal (+5V) (for D/A converter)
“L” is output at tuner off
39 DVSS — Ground terminal (for D/A converter)
PLL low-pass filter time constant selection signal output at AF SEEK
2 AF-SEEK O 40, 41 NCO O Not used (open)
“H” is output when AF SEEK Not used (open)
3 NCO O Not used (open) 42 AVCC — Power supply terminal (+5V) (for A/D converter)
FM stereo broadcasting detection signal input from the FM/AM tuner unit (TU1), or forced 43 AVRH I Reference voltage (+5V) input terminal (for A/D converter)
4 ST-MONO I/O monaural control signal output to the FM/AM tuner unit (TU1) 44 AVRL I Reference voltage (0V) input terminal (for A/D converter)
“L” is input in the FM stereo mode, or “L” is output in the forced monaural mode 45 AVSS — Ground terminal (for A/D converter)
5 TUNMUTE O Muting on/off control signal output of the FM and AM tuner signal “H”: muting on
Key input terminal (A/D input) (LSW901 to LSW903, S901, LSW905, LSW906)
FM system power supply on/off control signal output to the BA3918 (IC671) 46 KEYIN0 I OFF, SOURCE, MODE o, SEEK/AMS . m – > M +, SOUND, SHIFT keys
6 FM-ON O
“L”: AM power on, “H”: FM power on input
Tuner system power supply on/off control signal output to the BA3918 (IC671) Key input terminal (A/D input) (LSW921 to LSW923, LSW925 to LSW933)
7 TU-ON O
“H”: tuner power on 47 KEYIN1 I Z, PRST –/+ (XR-3100R), PRESET DISC –/+ (XR-C33R), AF/TA, PTY, DSPL, 6, 5, 4 t,
8 VCC — Power supply terminal (+5V) 3 PLAY MODE, 2 SET UP, 1 T keys input

9 NCO O Not used (open) 48 RC-IN0 I Rotary remote commander key input terminal (A/D input)
49 DSTSEL I Destination setting terminal (fixed at “H”)
Bus on/off control signal output to the SONY bus interface (IC701) “L”: bus on
10 BUS-ON O
Used for the XR-C33R only 50 NOISE DET I Noise level detection signal input at SEEK mode (A/D input)
11 SYSRST O Reset signal output to the SONY bus interface (IC701) “L”: reset Used for the XR-C33R only 51 D-BASS I D-BASS switch (S981) input terminal (A/D input)
12 DOORSW I Front panel open/close detection signal input “L” is input when the front panel is closed 52 MTP I Multi-path detection signal input from the RDS decoder (IC51)
13 LCD SO O Serial data output to the liquid crystal display driver (IC901) FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1)
53 VSM I
14 LCD CKO (A/D input)
O Serial data transfer clock signal output to the liquid crystal display driver (IC901)
15 BEEP O Beep sound drive signal output terminal 54 VCC — Power supply terminal (+5V)

16 LCD CE O Chip enable signal output to the liquid crystal display driver (IC901) “H” active Internal RAM reset detection signal input terminal
55 RAMBU I Input terminal to check that RAM data are not destroyed due to low voltage
17 UNISI I Serial data input from the SONY bus interface (IC701) Used for the XR-C33R only This checking is made within 100 msec after reset Fixed at “H” in this set
18 UNISO O Serial data output to the SONY bus interface (IC701) Used for the XR-C33R only 56 POWSEL I Power select switch (S501) input terminal “L”: off (halt mode), “H”: on (operation mode)
Serial data transfer clock signal output to the SONY bus interface (IC701) 57 NCO O Not used (open)
19 UNICKO O
Used for the XR-C33R only
58 TESTIN I Setting terminal for the test mode “L”: test mode, Normally: fixed at “H”
Station detector detect input from the FM/AM tuner unit (TU1)
20 SD-IN I LED drive signal output of the door indicator “H”: LED on
Stop level for SEEK, BTM, etc. is determined SD is present at input of “H” 59 DOOR-IND O
“H” is output to turn on LED when front panel is opened Not used (open)
21 to 23 NCO O Not used (open)
Muting control signal output to the electrical volume (IC401)
24 SIRCS I Sircs remote control signal input terminal Not used (fixed at “H”) 60 EVOL MUTE O
Volume minimum: “∞” output (“H” active)
25 PLLSI I PLL serial data input from the FM/AM PLL (IC1)
Setting terminal for the illumination color
26 PLLSO O 61 K SEL0 I
PLL serial data output to the FM/AM PLL (IC1) “L”: 2 colors, “H”: 1 color (fixed at “H” in this set)
27 PLLCKO O PLL serial data transfer clock signal output to the FM/AM PLL (IC1) Setting terminal for the illumination color “L”: amber (fixed at “L” in XR-3100R and
62 K SEL1 I
28 PLLCE O PLL chip enable signal output to the FM/AM PLL (IC1) “H” active XR-C33R: amber), “H”: green (fixed at “H” in XR-C33R: green)
Power on/off control signal output of the illumination LED and liquid crystal display driver 63 VSS — Ground terminal
(IC901) “H”: power on Depends on initial setting of power select switch (S501) 64 NCO O Not used (open)
29 ILL-ON O
Power select switch (S501) on: “H” output at the accessory on
65 MUTE O Audio line muting on/off control signal output terminal “H”: muting on
Power select switch (S501) off: “H” output at the power on
66, 67 NCO O Not used (open)
30, 31 NCO O Not used (open)
68 AMP MUTE O Muting on/off control signal output to the power amplifier (IC611) “L”: muting on
32 NOISE ON O Discharge control signal output for the noise detection circuit “H”: discharge
Internal flash memory data write mode detection signal input terminal “L”: data write mode
33 VSS — Ground terminal 69 FLASH-W I
Not used (fixed at “H” in this set)
34 C — Connected to coupling capacitor for the power supply
70 I2C SIO I/O Two-way data bus with the RDS decoder (IC51) and electrical volume (IC401)
A/D converter power control signal output terminal
71 I2C CKO O Bus clock signal output to the RDS decoder (IC51) and electrical volume (IC401)
35 AD-ON O When the KEYACK (pin uh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input 72 RC-IN1 I Rotary remote commander shift key input terminal “L”: shift
73 X1A O Sub system clock output terminal (32.768 kHz)
74 X0A I Sub system clock input terminal (32.768 kHz)

32 32

Downloaded from www.Manualslib.com manuals search engine

 Pin No. Pin Name I/O Description
75 DAVN I Data transmit completed detect signal input from the RDS decoder (IC51) “H” active
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
76 KEYACK I
and eject keys in the power off status On at input of “H”
Battery detect signal input from the SONY bus interface (IC701) and battery detect circuit
77 BU-IN I
“L” is input at low voltage IC701: Used for the XR-C33R only
Auto dimmer control illumination line detection signal input terminal
78 ILL IN I
“L” is input at dimmer detection Fixed at “L” in this set
Telephone muting signal input terminal At input of “H”, the signal is attenuated by –20 dB
79 TEL-ATT I
Not used (open)
Front panel block remove/attach detection signal input terminal
80 NOSESW I
“L”: front panel is attached
81 ACC IN I Accessory detect signal input terminal “L”: accessory on
82 to 85 NCO O Not used (open)
86 HSTX I Hardware standby input terminal “L”: hardware standby mode Reset signal input in this set
87 MD2 I Setting terminal for the CPU operational mode (fixed at “L” in this set)
88, 89 MD1, MD0 I Setting terminal for the CPU operational mode (fixed at “H” in this set)
System reset signal input from the reset signal generator (IC652) and reset switch (S503)
90 RESET I
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
91 VSS — Ground terminal
92 X0 I Main system clock input terminal (3.68 MHz)
93 X1 O Main system clock output terminal (3.68 MHz)
94 VCC — Power supply terminal (+5V)
95 to 99 NCO O Not used (open)
AM frequency step (9 kHz or 10 kHz) selection signal input terminal
100 9K/10K I
“L”: 9 kHz, “H”: 10 kHz Not used (open)
101 NCO O Not used (open)
102 MTLIN I Auto metal detection signal input terminal “L”: auto metal Fixed at “L” in this set
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
103 AMSIN I
“L”: music is present, “H”: music is not present
Rotation detect signal input from supply reel sensor and take-up reel sensor on the deck
104 REEL I
mechanism
105 POS0 I
Tape position (EJECT/FF/REW/ POS0: “L”: EJECT mode, “H”: others mode
106 POS1 I REV/FWD mode) detect input from POS1: “L”: FF and FWD mode, “H”: others mode
107 POS2 I the tape operation switch on the deck POS2: “L”: REW mode, “H”: others mode
mechanism POS3: “L”: REV and EJECT mode, “H”: others mode
108 POS3 I
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
109 LM-EJ O
(For the eject direction and reverse side operation) *1
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
110 LM-LOD O
(For the loading direction and forward side operation) *1
111 CM-ON O Capstan/reel motor (M901) drive signal output terminal “H”: motor on
112 TAPEON O Tape system power supply on/off control signal output terminal “H”: tape on
Forward/reverse direction control signal output to the CXA2509AQ (IC301)
113 N-ROUT O
“L”: forward direction, “H”: reverse direction
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
114 AMSON O
“L” is output to lower the gain for audio level at FF/REW mode
METAL control in/out terminal
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)
115 MTLON I/O
At manual mode: METAL on/off control signal output terminal (METAL on at “H” output)
At auto mode: input at MTLIN (pin <z/x)

33
Downloaded from www.Manualslib.com manuals search engine
 Pin No. Pin Name I/O Description
Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (valid at “L” input)
116 DOLON I/O
At normal mode: dolby on/off control signal output terminal (dolby on at “H” output)
Not used this function (fixed at “H”)
Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: muting on
117 TAPE MUTE O
Active at ATA, FF/REW mode
Standby on/off control signal output to the power amplifier (IC611)
118 AMP ON O
“L”: standby mode, “H”: amp on
119 VSS — Ground terminal
120 POWON O Main system power supply on/off control signal output to the BA3918 (IC671) “H”: power on

*1 Loading/tape operation motor control

Mode LOADING/ EJECT/
STOP BRAKE
Terminal FORWARD REVERSE
LM-LOD (pin <zz/) “L” “H” “L” “H”
LM-EJ (pin <z/.) “L” “L” “H” “H”

34
Downloaded from www.Manualslib.com manuals search engine
 SECTION 7
EXPLODED VIEWS
NOTE: • Abbreviation
• -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they AMBER : Amber illumination type
may have some difference from the original are seldom required for routine service. Some GREEN : Green illumination type
one. delay should be anticipated when ordering
• Color Indication of Appearance Parts these items.
Example: • The mechanical parts with no reference num-
KNOB, BALANCE (WHITE) . . . (RED) ber in the exploded views are not supplied.
↑ ↑ • Hardware (# mark) list and accessories and
Parts Color Cabinet's Color packing materials are given in the last of the
electrical parts list.

10
(1) CHASSIS SECTION
not supplied 11
12 13

(C33R)
MG-25G-136 #3 14
F801
15

9 7
(C33R) #2
6
#2
TU1
5 #2

#4 (C33R)
#2

#2
16

8
#2
2 4 17
3

18

19

#2
1
#2

Front panel section

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 3-030-828-01 PANEL, SUB 11 3-012-859-01 CAP (25), RUBBER
2 X-3367-636-1 LOCK ASSY 12 3-937-650-01 PLATE (C), GROUND
3 3-027-437-41 DOOR, CASSETTE 13 1-782-093-11 CORD (WITH CONNECTOR) (ISO-S)
4 3-935-003-01 SPRING, TORSION (SPEAKER)
* 5 A-3326-071-A MAIN BOARD, COMPLETE (3100R) 14 1-777-989-21 CORD (WITH CONNECTOR) (AMP REM)
(C33R)
* 5 A-3326-073-A MAIN BOARD, COMPLETE (C33R: AMBER) 15 1-782-092-11 CORD (WITH CONNECTOR) (ISO-P) (POWER)
* 5 A-3326-106-A MAIN BOARD, COMPLETE (C33R: GREEN)
* 6 3-031-828-01 BRACKET (REG. IC) 16 3-935-014-01 CUSHION (U)
* 7 3-019-147-01 BRACKET (IC) (M) * 17 3-009-306-01 SHEET, INSULATING
* 8 3-031-050-02 HEAT SINK (C33R) * 18 3-009-813-43 CHASSIS
19 3-042-244-11 SCREW (T)
* 8 3-031-056-01 HEAT SINK (3100R) F801 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
9 3-915-923-01 SCREW, GROUND POINT
* 10 X-3373-269-1 COVER ASSY (ISO) TU1 1-693-440-23 TUNER UNIT (FM/AM TUNER UNIT)

35
Downloaded from www.Manualslib.com manuals search engine
 (2) FRONT PANEL SECTION

66

60 65

59 64 #5
LCD901 63
62
56
61
58 55

not supplied
57 (KEY board)
54

53

52

51

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 3-030-835-01 BUTTON (1-6) (OFF. SHIFT. 1. 2. 3. 4. 5. 6) 59 3-030-830-01 KNOB (VOL)
52 3-030-837-01 BUTTON (D-BASS) 60 3-030-832-01 LEVER (S/A) (+. –)
53 3-030-838-03 BUTTON (RELEASE) * 61 3-030-840-01 PLATE (B), GROUND
54 3-932-475-01 SPRING (RELEASE) * 62 3-030-839-01 SHEET (REFLECTOR)
55 X-3378-491-1 PANEL SUB ASSY (C33R) * 63 3-030-824-01 PLATE, LIGHT GUIDE

55 X-3378-492-1 PANEL SUB ASSY (3100R) 64 1-694-508-11 CONDUCTIVE BOARD, CONNECTION

56 3-030-834-01 BUTTON (M/S) (MODE o. SOUND) * 65 3-030-825-01 HOLDER (LCD)
57 3-030-836-01 BUTTON (D/P/A) 66 3-030-827-01 PANEL, FRONT BACK
(Z. – DISC +. DSPL. PTY. AF/TA) (C33R) LCD901 1-803-497-11 DISPLAY PANEL, LIQUID CRYSTAL
57 3-031-027-01 BUTTON (P/P/A)
(Z. – PRST +. DSPL. PTY. AF/TA) (3100R)
58 3-030-831-02 BUTTON (SOURCE)

36
Downloaded from www.Manualslib.com manuals search engine
 (3) MECHANISM DECK SECTION
(MG-25G-136)

160
159

163
158

HP901
155 161
154

157 162

#6

156 M901
A
164

153 152

not supplied

#7
168
168
166

167

151 165

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 X-3291-667-A CLUTCH (FR) ASSY 161 3-933-346-01 CATCHER
* 152 3-019-130-01 LEVER (LDG-A) 162 3-933-344-01 GUIDE (C)
* 153 3-019-131-01 LEVER (LDG-B) 163 3-014-798-01 SCREW (HEAD), SPECIAL
154 3-020-539-01 SPRING (LD-1), TENSION 164 3-364-151-01 WASHER
155 3-020-540-01 SPRING (LD-2), TENSION 165 A-3220-610-A MECHANISM DECK ASSY

156 3-020-542-01 GEAR (LOADING FT) 166 3-017-302-01 BELT (25)

157 3-341-753-11 WASHER, POLYETHYLENE 167 3-936-853-01 FLYWHEEL (F)
158 3-020-533-01 HOUSING 168 3-701-437-21 WASHER
* 159 3-020-532-01 ARM (SUCTION) HP901 1-500-196-21 HEAD, MAGNETIC (PLAYBACK)
160 3-020-534-01 HANGER M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)

37
Downloaded from www.Manualslib.com manuals search engine
 SECTION 8
KEY ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they • Abbreviation
parts list may be different from the parts speci- are seldom required for routine service. AMBER : Amber illumination type
fied in the diagrams or the components used Some delay should be anticipated when order- GREEN : Green illumination type
on the set. ing these items.
When indicating parts by reference
• -XX and -X mean standardized parts, so they • SEMICONDUCTORS number, please include the board.
may have some difference from the original In each case, u: µ, for example:
one. uA. . : µA. . uPA. . : µPA. .
• RESISTORS uPB. . : µPB. . uPC. . : µPC. .
All resistors are in ohms. uPD. . : µPD. .
METAL: Metal-film resistor. • CAPACITORS
METAL OXIDE: Metal oxide-film resistor. uF: µF
F: nonflammable • COILS
uH: µH

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
KEY BOARD LSW905 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (SOUND)
********** (GREEN)
LSW906 1-771-609-11 SWITCH, TACTILE (WITH LED) (SHIFT)
1-694-508-11 CONDUCTIVE BOARD, CONNECTION (GREEN)
* 3-030-824-01 PLATE, LIGHT GUIDE LSW906 1-771-882-21 SWITCH, TACTILE (WITH LED) (SHIFT)
* 3-030-825-01 HOLDER (LCD) (AMBER)
* 3-030-839-01 SHEET (REFLECTOR)
* 3-030-840-01 PLATE (B), GROUND LSW921 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (Z)
(AMBER)
< CAPACITOR > LSW921 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (Z)
(GREEN)
C952 1-163-033-00 CERAMIC CHIP 0.022uF 50V LSW922 1-762-617-21 SWITCH, KEY BOARD (WITH LED)
C953 1-163-251-11 CERAMIC CHIP 100PF 5% 50V (3100R: PRST –/C33R: PRESET –, DISC –)
C954 1-165-319-11 CERAMIC CHIP 0.1uF 50V (AMBER)
C955 1-165-319-11 CERAMIC CHIP 0.1uF 50V LSW922 1-762-619-21 SWITCH, KEY BOARD (WITH LED)
C956 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V (3100R: PRST –/C33R: PRESET –, DISC –)
(GREEN)
< CONNECTOR > LSW923 1-762-617-21 SWITCH, KEY BOARD (WITH LED)
(3100R: PRST +/C33R: PRESET +, DISC +)
CNP901 1-785-773-11 PIN, CONNECTOR 15P (AMBER)

< DIODE > LSW923 1-762-619-21 SWITCH, KEY BOARD (WITH LED)
(3100R: PRST +/C33R: PRESET +, DISC +)
D902 8-719-056-82 DIODE UDZ-TE-17-6.2B (GREEN)
D903 8-719-056-82 DIODE UDZ-TE-17-6.2B LSW925 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (AF/TA)
D904 8-719-056-82 DIODE UDZ-TE-17-6.2B (AMBER)
D951 8-719-976-99 DIODE UDZ-TE-17-5.1B LSW925 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (AF/TA)
(GREEN)
< IC > LSW926 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (PTY)
(AMBER)
IC901 8-759-366-34 IC LC75824E LSW926 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (PTY)
(GREEN)
< LIQUID CRYSTAL DISPLAY >
LSW927 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (DSPL)
LCD901 1-803-497-11 DISPLAY PANEL, LIQUID CRYSTAL (AMBER)
LSW927 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (DSPL)
< SWITCH > (GREEN)
LSW928 1-771-609-11 SWITCH, TACTILE (WITH LED) (6) (GREEN)
LSW901 1-771-609-11 SWITCH, TACTILE (WITH LED) (OFF) (GREEN) LSW928 1-771-882-21 SWITCH, TACTILE (WITH LED) (6) (AMBER)
LSW901 1-771-882-21 SWITCH, TACTILE (WITH LED) (OFF) (AMBER) LSW929 1-771-609-11 SWITCH, TACTILE (WITH LED) (5) (GREEN)
LSW902 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (SOURCE)
(AMBER) LSW929 1-771-882-21 SWITCH, TACTILE (WITH LED) (5) (AMBER)
LSW902 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (SOURCE) LSW930 1-771-609-11 SWITCH, TACTILE (WITH LED) (4, t)
(GREEN) (GREEN)
LSW903 1-762-617-21 SWITCH, KEY BOARD (WITH LED) LSW930 1-771-882-21 SWITCH, TACTILE (WITH LED) (4, t)
(MODE, o) (AMBER) (AMBER)
LSW931 1-771-609-11 SWITCH, TACTILE (WITH LED)
LSW903 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (3, PLAY MODE) (GREEN)
(MODE, o) (GREEN) LSW931 1-771-882-21 SWITCH, TACTILE (WITH LED)
LSW905 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (SOUND) (3, PLAY MODE) (AMBER)
(AMBER)

38
Downloaded from www.Manualslib.com manuals search engine
 KEY MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
LSW932 1-771-609-11 SWITCH, TACTILE (WITH LED) (2, SET UP) R969 1-216-037-00 METAL CHIP 330 5% 1/10W
(GREEN) (AMBER)
LSW932 1-771-882-21 SWITCH, TACTILE (WITH LED) (2, SET UP)
(AMBER) R975 1-216-029-00 METAL CHIP 150 5% 1/10W
LSW933 1-771-609-11 SWITCH, TACTILE (WITH LED) (1, T) (GREEN)
(GREEN) R975 1-216-037-00 METAL CHIP 330 5% 1/10W
LSW933 1-771-882-21 SWITCH, TACTILE (WITH LED) (1, T) (AMBER)
(AMBER) R977 1-216-037-00 METAL CHIP 330 5% 1/10W
R981 1-216-655-11 METAL CHIP 1.5K 0.5% 1/10W
< PILOT LAMP > R982 1-216-663-11 METAL CHIP 3.3K 0.5% 1/10W

PL901 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT) R983 1-216-671-11 METAL CHIP 6.8K 0.5% 1/10W
PL902 1-517-633-21 LAMP, PILOT (LCD BACK LIGHT) R984 1-216-081-00 METAL CHIP 22K 5% 1/10W
R990 1-216-295-00 SHORT 0
< TRANSISTOR > R991 1-216-295-00 SHORT 0

Q945 8-729-900-53 TRANSISTOR DTC114EKA-T146 < ROTARY ENCODER >

< RESISTOR > RE901 1-475-014-11 ENCODER, ROTARY (VOLUME/BASS/TREBLE/

BALANCE/FADER CONTROL)
R901 1-216-647-11 METAL CHIP 680 0.5% 1/10W
R902 1-216-647-11 METAL CHIP 680 0.5% 1/10W < SWITCH >
R903 1-216-647-11 METAL CHIP 680 0.5% 1/10W
R904 1-216-651-11 METAL CHIP 1K 0.5% 1/10W S901 1-771-290-11 SWITCH, SLIDE
R905 1-216-655-11 METAL CHIP 1.5K 0.5% 1/10W (SEEK/AMS, > M +, . m –)
S981 1-762-937-11 SWITCH, ROTARY (D-BASS)
R906 1-216-655-11 METAL CHIP 1.5K 0.5% 1/10W **************************************************************
R907 1-216-659-11 METAL CHIP 2.2K 0.5% 1/10W
R921 1-216-647-11 METAL CHIP 680 0.5% 1/10W * A-3326-071-A MAIN BOARD, COMPLETE (3100R)
R922 1-216-647-11 METAL CHIP 680 0.5% 1/10W * A-3326-073-A MAIN BOARD, COMPLETE (C33R: AMBER)
R923 1-216-647-11 METAL CHIP 680 0.5% 1/10W * A-3326-106-A MAIN BOARD, COMPLETE (C33R: GREEN)
*********************
R924 1-216-651-11 METAL CHIP 1K 0.5% 1/10W
R925 1-216-655-11 METAL CHIP 1.5K 0.5% 1/10W * 3-019-147-01 BRACKET (IC) (M)
R926 1-216-655-11 METAL CHIP 1.5K 0.5% 1/10W * 3-031-050-02 HEAT SINK (C33R)
R927 1-216-659-11 METAL CHIP 2.2K 0.5% 1/10W * 3-031-056-01 HEAT SINK (3100R)
R928 1-216-663-11 METAL CHIP 3.3K 0.5% 1/10W * 3-031-828-01 BRACKET (REG. IC)
7-685-793-09 SCREW +PTT 2.6X8 (S)
R929 1-216-667-11 METAL CHIP 4.7K 0.5% 1/10W
R930 1-216-671-11 METAL CHIP 6.8K 0.5% 1/10W 7-685-795-09 SCREW +PTT 2.6X12 (S)
R931 1-208-806-11 RES, CHIP 10K 2% 1/10W
R932 1-208-810-11 RES, CHIP 15K 2% 1/10W < CAPACITOR >
R951 1-216-041-00 METAL CHIP 470 5% 1/10W
C1 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
R953 1-216-121-00 RES, CHIP 1M 5% 1/10W C2 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
R954 1-216-049-11 RES, CHIP 1K 5% 1/10W C3 1-124-233-11 ELECT 10uF 20% 16V
R955 1-216-049-11 RES, CHIP 1K 5% 1/10W C4 1-124-233-11 ELECT 10uF 20% 16V
R956 1-216-049-11 RES, CHIP 1K 5% 1/10W C5 1-124-233-11 ELECT 10uF 20% 16V
R957 1-216-109-00 METAL CHIP 330K 5% 1/10W
C6 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
R961 1-216-021-00 METAL CHIP 68 5% 1/10W C7 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
(GREEN) C8 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
R961 1-216-029-00 METAL CHIP 150 5% 1/10W C10 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
(AMBER) C11 1-163-020-00 CERAMIC CHIP 0.0082uF 10% 50V
R963 1-216-033-00 METAL CHIP 220 5% 1/10W
(GREEN) C12 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
R963 1-216-037-00 METAL CHIP 330 5% 1/10W C13 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
(AMBER) C14 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
R965 1-216-033-00 METAL CHIP 220 5% 1/10W C15 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(GREEN) C16 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V

R965 1-216-037-00 METAL CHIP 330 5% 1/10W C17 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(AMBER) C18 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
R967 1-216-033-00 METAL CHIP 220 5% 1/10W C19 1-163-059-00 CERAMIC CHIP 0.01uF 10% 50V
(GREEN) C20 1-124-234-00 ELECT 22uF 20% 16V
R967 1-216-037-00 METAL CHIP 330 5% 1/10W C21 1-163-091-00 CERAMIC CHIP 8PF 50V
(AMBER)
R969 1-216-033-00 METAL CHIP 220 5% 1/10W C22 1-163-231-11 CERAMIC CHIP 15PF 5% 50V
(GREEN) C23 1-163-087-00 CERAMIC CHIP 4PF 50V

39
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C24 1-163-133-00 CERAMIC CHIP 470PF 5% 50V C183 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
C25 1-124-233-11 ELECT 10uF 20% 16V C184 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C26 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C201 1-163-263-11 CERAMIC CHIP 330PF 5% 50V

C27 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C202 1-163-263-11 CERAMIC CHIP 330PF 5% 50V
C33 1-163-133-00 CERAMIC CHIP 470PF 5% 50V C205 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C34 1-163-133-00 CERAMIC CHIP 470PF 5% 50V C207 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
C51 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C208 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C52 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C210 1-163-007-11 CERAMIC CHIP 680PF 10% 50V

C53 1-163-229-11 CERAMIC CHIP 12PF 5% 50V C211 1-126-163-11 ELECT 4.7uF 20% 50V
C54 1-163-229-11 CERAMIC CHIP 12PF 5% 50V C235 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V
C55 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C241 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C56 1-124-234-00 ELECT 22uF 20% 16V (C33R)
C57 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C242 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
(C33R)
C58 1-163-263-11 CERAMIC CHIP 330PF 5% 50V C251 1-163-020-00 CERAMIC CHIP 0.0082uF 10% 50V
C59 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C60 1-163-135-00 CERAMIC CHIP 560PF 5% 50V C252 1-124-257-00 ELECT 2.2uF 20% 50V
C61 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V C253 1-124-257-00 ELECT 2.2uF 20% 50V
C62 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C271 1-126-163-11 ELECT 4.7uF 20% 50V
C273 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
C63 1-163-133-00 CERAMIC CHIP 470PF 5% 50V C274 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C64 1-124-233-11 ELECT 10uF 20% 16V
C71 1-124-234-00 ELECT 22uF 20% 16V C281 1-126-163-11 ELECT 4.7uF 20% 50V
C73 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C282 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C81 1-124-589-11 ELECT 47uF 20% 16V (C33R)
C283 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
C82 1-124-234-00 ELECT 22uF 20% 16V C284 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C83 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C301 1-124-584-00 ELECT 100uF 20% 10V
C90 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C91 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C302 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C92 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C303 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
C304 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C93 1-163-133-00 CERAMIC CHIP 470PF 5% 50V C305 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C94 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V C306 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C95 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
C96 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V C331 1-124-234-00 ELECT 22uF 20% 16V
C97 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C361 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C362 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C98 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C363 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C101 1-163-263-11 CERAMIC CHIP 330PF 5% 50V C364 1-126-157-11 ELECT 10uF 20% 16V
C102 1-163-263-11 CERAMIC CHIP 330PF 5% 50V
C105 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C365 1-124-234-00 ELECT 22uF 20% 16V
C107 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V C366 1-126-933-11 ELECT 100uF 20% 16V
C401 1-124-584-00 ELECT 100uF 20% 10V
C108 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C402 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C110 1-163-007-11 CERAMIC CHIP 680PF 10% 50V C404 1-124-233-11 ELECT 10uF 20% 16V
C111 1-126-163-11 ELECT 4.7uF 20% 50V
C121 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V C405 1-124-234-00 ELECT 22uF 20% 16V
C122 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V C408 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C502 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C123 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V C503 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C135 1-163-227-11 CERAMIC CHIP 10PF 0.5PF 50V C504 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C141 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(C33R) C505 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C142 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V C506 1-163-102-00 CERAMIC CHIP 24PF 5% 50V
(C33R) C507 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C151 1-163-020-00 CERAMIC CHIP 0.0082uF 10% 50V C509 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C510 1-124-584-00 ELECT 100uF 20% 10V
C152 1-124-257-00 ELECT 2.2uF 20% 50V
C153 1-124-257-00 ELECT 2.2uF 20% 50V C511 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C171 1-126-163-11 ELECT 4.7uF 20% 50V C527 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C173 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V C601 1-107-885-31 ELECT 3300uF 20% 16V
C174 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C602 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C603 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C181 1-126-163-11 ELECT 4.7uF 20% 50V (C33R)
C182 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(C33R) C611 1-124-233-11 ELECT 10uF 20% 16V

40
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C612 1-124-233-11 ELECT 10uF 20% 16V D556 8-719-056-82 DIODE UDZ-TE-17-6.2B
C613 1-109-982-11 CERAMIC CHIP 1uF 10% 10V D557 8-719-056-82 DIODE UDZ-TE-17-6.2B
C614 1-107-909-11 ELECT 47uF 20% 16V
C616 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V D558 8-719-056-82 DIODE UDZ-TE-17-6.2B
D559 8-719-056-82 DIODE UDZ-TE-17-6.2B
C617 1-136-165-00 MYLAR 0.1uF 5% 50V D561 8-719-056-82 DIODE UDZ-TE-17-6.2B
C621 1-124-589-11 ELECT 47uF 20% 16V D562 8-719-056-82 DIODE UDZ-TE-17-6.2B
C622 1-124-257-00 ELECT 2.2uF 20% 50V D601 8-719-049-38 DIODE 1N5404TU
C623 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C631 1-164-222-11 CERAMIC CHIP 0.22uF 25V D602 8-719-056-93 DIODE UDZ-TE-17-18B
D603 8-719-056-93 DIODE UDZ-TE-17-18B (C33R)
C632 1-164-222-11 CERAMIC CHIP 0.22uF 25V D604 8-719-056-82 DIODE UDZ-TE-17-6.2B
C641 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V D611 8-719-053-18 DIODE 1SR154-400TE-25
C653 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V D612 8-719-053-18 DIODE 1SR154-400TE-25
C654 1-125-701-11 DOUBLE LAYER 0.047F 5.5V
C655 1-126-933-11 ELECT 100uF 20% 16V D613 8-719-053-18 DIODE 1SR154-400TE-25
D614 8-719-053-18 DIODE 1SR154-400TE-25
C661 1-109-982-11 CERAMIC CHIP 1uF 10% 10V D615 8-719-053-18 DIODE 1SR154-400TE-25
C671 1-126-157-11 ELECT 10uF 20% 16V D616 8-719-053-18 DIODE 1SR154-400TE-25
C672 1-126-157-11 ELECT 10uF 20% 16V D617 8-719-053-18 DIODE 1SR154-400TE-25
C673 1-126-157-11 ELECT 10uF 20% 16V
C674 1-126-157-11 ELECT 10uF 20% 16V D618 8-719-053-18 DIODE 1SR154-400TE-25
D621 8-719-422-12 DIODE UDZ-TE-17-3.9B
C675 1-126-157-11 ELECT 10uF 20% 16V D622 8-719-073-01 DIODE MA111-TX
C676 1-126-157-11 ELECT 10uF 20% 16V D623 8-719-977-22 DIODE UDZ-TE-17-9.1B
C701 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V D624 8-719-073-01 DIODE MA111-TX
(C33R)
C702 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V D631 8-719-158-49 DIODE UDZ-TE-17-12B
C703 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V D651 8-719-911-19 DIODE 1SS119-25TD
(C33R) D653 8-719-073-01 DIODE MA111-TX
D661 8-719-073-01 DIODE MA111-TX
C704 1-163-077-00 CERAMIC CHIP 0.1uF 10% 25V D662 8-719-056-85 DIODE UDZ-TE-17-8.2B
(C33R)
D671 8-719-970-02 DIODE 1SR139-400T-32 (C33R)
< CONNECTOR > D672 8-719-970-02 DIODE 1SR139-400T-32
D673 8-719-970-02 DIODE 1SR139-400T-32
CN301 1-766-260-11 CONNECTOR, FFC/FPC (ZIF) 7P D674 8-719-970-02 DIODE 1SR139-400T-32 (C33R)
* CN302 1-506-995-11 PIN, CONNECTOR (PC BOARD) 13P D701 8-719-056-93 DIODE UDZ-TE-17-18B
CN500 1-785-772-11 PLUG, CONNECTOR 15P
CN601 1-785-761-11 PIN, CONNECTOR (ISO) (POWER) D702 8-719-017-62 DIODE MA8068-L-TX (C33R)
CN701 1-580-907-31 PLUG, CONNECTOR (BUS CONTROL IN) D703 8-719-056-82 DIODE UDZ-TE-17-6.2B (C33R)
(C33R) D704 8-719-056-93 DIODE UDZ-TE-17-18B (C33R)
D705 8-719-056-93 DIODE UDZ-TE-17-18B (C33R)
CNJ151 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN, AUDIO OUT) D706 8-719-072-70 DIODE MA2ZD14001S0 (C33R)
(C33R)
D707 8-719-056-84 DIODE UDZ-TE-17-7.5B (3100R)
< DIODE >
< FERRITE BEAD >
D1 8-719-991-65 DIODE SB02W03C-TB
D61 8-719-422-12 DIODE UDZ-TE-17-3.9B FB501 1-414-233-22 FERRITE BEAD INDUCTOR
D71 8-719-158-15 DIODE UDZ-TE-17-5.6B
D81 8-719-977-28 DIODE UDZ-TE-17-10B < IC >
D90 8-719-073-01 DIODE MA111-TX
IC1 8-759-586-59 IC TB2118F-EL-S
D91 8-719-073-01 DIODE MA111-TX IC51 8-759-650-68 IC SAA6588T/V2-118
D92 8-719-976-99 DIODE UDZ-TE-17-5.1B IC90 8-759-909-71 IC BA4558F
D93 8-719-422-12 DIODE UDZ-TE-17-3.9B IC301 8-752-079-78 IC CXA2509AQ-T4
D361 8-719-977-22 DIODE UDZ-TE-17-9.1B IC361 8-759-823-87 IC LB1638M
D362 8-719-911-19 DIODE 1SS119-25TD
IC401 8-759-572-10 IC TDA7462D013TR
D441 8-719-056-82 DIODE UDZ-TE-17-6.2B (C33R) IC501 8-759-659-11 IC MB90574PMT-G-222-BND
D481 8-719-056-82 DIODE UDZ-TE-17-6.2B (C33R) IC611 8-759-486-44 IC TDA7386
D501 8-719-914-44 DIODE DAP202K-T-146 IC652 8-759-574-61 IC XC61AN4302MR
D551 8-719-056-82 DIODE UDZ-TE-17-6.2B IC671 8-759-347-50 IC BA3918-V3
D552 8-719-056-82 DIODE UDZ-TE-17-6.2B
IC701 8-759-449-89 IC BA8270F-E2 (C33R)
D553 8-719-056-82 DIODE UDZ-TE-17-6.2B
D554 8-719-056-82 DIODE UDZ-TE-17-6.2B
D555 8-719-056-93 DIODE UDZ-TE-17-18B

41
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< JACK > R51 1-216-097-00 RES, CHIP 100K 5% 1/10W
R52 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
J1 1-764-808-21 JACK (ANT) (FM/AM ANTENNA) R53 1-216-113-00 METAL CHIP 470K 5% 1/10W
J501 1-566-822-41 JACK (REMOTE IN)
R54 1-216-049-11 RES, CHIP 1K 5% 1/10W
< SHORT > R55 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R56 1-216-041-00 METAL CHIP 470 5% 1/10W
JC1 1-216-295-00 SHORT 0 R57 1-216-037-00 METAL CHIP 330 5% 1/10W
JC301 1-216-295-00 SHORT 0 R58 1-216-037-00 METAL CHIP 330 5% 1/10W
JC503 1-216-295-00 SHORT 0
R59 1-216-001-00 METAL CHIP 10 5% 1/10W
< COIL > R60 1-216-009-00 RES, CHIP 22 5% 1/10W
R61 1-216-037-00 METAL CHIP 330 5% 1/10W
L1 1-410-989-11 INDUCTOR CHIP 0.47uH R62 1-216-045-00 METAL CHIP 680 5% 1/10W
L51 1-410-509-11 INDUCTOR 10uH R71 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
L601 1-411-669-21 CHOKE COIL
R81 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
< TRANSISTOR > R90 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R91 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q51 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R92 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
Q61 8-729-921-25 TRANSISTOR FMC2-T148 R93 1-216-097-00 RES, CHIP 100K 5% 1/10W
Q71 8-729-015-11 TRANSISTOR 2SD1802FAST-TL
Q81 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R94 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
Q82 8-729-921-25 TRANSISTOR FMC2-T148 R95 1-216-121-00 RES, CHIP 1M 5% 1/10W
R96 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
Q90 8-729-900-53 TRANSISTOR DTC114EKA-T146 R97 1-216-049-11 RES, CHIP 1K 5% 1/10W
Q121 8-729-920-21 TRANSISTOR DTC314TK-T-146 R101 1-216-097-00 RES, CHIP 100K 5% 1/10W
Q151 8-729-920-21 TRANSISTOR DTC314TK-T-146
Q171 8-729-920-21 TRANSISTOR DTC314TK-T-146 R102 1-216-097-00 RES, CHIP 100K 5% 1/10W
Q181 8-729-920-21 TRANSISTOR DTC314TK-T-146 R105 1-216-109-00 METAL CHIP 330K 5% 1/10W
R106 1-216-077-00 RES, CHIP 15K 5% 1/10W
Q251 8-729-920-21 TRANSISTOR DTC314TK-T-146 R107 1-216-079-00 METAL CHIP 18K 5% 1/10W
Q271 8-729-920-21 TRANSISTOR DTC314TK-T-146 R108 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q281 8-729-920-21 TRANSISTOR DTC314TK-T-146
Q361 8-729-015-11 TRANSISTOR 2SD1802FAST-TL R109 1-216-077-00 RES, CHIP 15K 5% 1/10W
Q362 8-729-921-25 TRANSISTOR FMC2-T148 R110 1-216-041-00 METAL CHIP 470 5% 1/10W
R121 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
Q364 8-729-106-60 TRANSISTOR 2SB1132-T100-R R141 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q365 8-729-900-53 TRANSISTOR DTC114EKA-T146 (C33R)
Q621 8-729-027-23 TRANSISTOR DTA114EKA-T146 R142 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q622 8-729-021-94 FET 2SK1657-T1B (C33R)
Q631 8-729-423-99 TRANSISTOR 2SD2137-OP-TA
R151 1-216-077-00 RES, CHIP 15K 5% 1/10W
Q633 8-729-921-25 TRANSISTOR FMC2-T148 R152 1-216-085-00 METAL CHIP 33K 5% 1/10W
Q651 8-729-027-23 TRANSISTOR DTA114EKA-T146 R171 1-216-033-00 METAL CHIP 220 5% 1/10W
Q652 8-729-027-23 TRANSISTOR DTA114EKA-T146 R172 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
Q661 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R173 1-216-089-00 RES, CHIP 47K 5% 1/10W
Q701 8-729-900-53 TRANSISTOR DTC114EKA-T146
R174 1-216-121-00 RES, CHIP 1M 5% 1/10W
Q702 1-801-806-11 TRANSISTOR DTC144EKA-T146 (3100R) R181 1-216-033-00 METAL CHIP 220 5% 1/10W
Q703 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R182 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
(3100R) R183 1-216-089-00 RES, CHIP 47K 5% 1/10W
R184 1-216-121-00 RES, CHIP 1M 5% 1/10W
< RESISTOR >
R201 1-216-097-00 RES, CHIP 100K 5% 1/10W
R1 1-216-049-11 RES, CHIP 1K 5% 1/10W R202 1-216-097-00 RES, CHIP 100K 5% 1/10W
R2 1-216-029-00 METAL CHIP 150 5% 1/10W R205 1-216-109-00 METAL CHIP 330K 5% 1/10W
R3 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R206 1-216-077-00 RES, CHIP 15K 5% 1/10W
R6 1-216-073-00 METAL CHIP 10K 5% 1/10W R207 1-216-079-00 METAL CHIP 18K 5% 1/10W
R7 1-216-073-00 METAL CHIP 10K 5% 1/10W
R208 1-216-073-00 METAL CHIP 10K 5% 1/10W
R8 1-216-073-00 METAL CHIP 10K 5% 1/10W R209 1-216-077-00 RES, CHIP 15K 5% 1/10W
R11 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R210 1-216-041-00 METAL CHIP 470 5% 1/10W
R12 1-216-067-00 METAL CHIP 5.6K 5% 1/10W R241 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R13 1-216-025-00 RES, CHIP 100 5% 1/10W (C33R)
R14 1-216-067-00 METAL CHIP 5.6K 5% 1/10W R242 1-216-073-00 METAL CHIP 10K 5% 1/10W
(C33R)
R15 1-216-025-00 RES, CHIP 100 5% 1/10W
R16 1-216-073-00 METAL CHIP 10K 5% 1/10W R251 1-216-077-00 RES, CHIP 15K 5% 1/10W

42
Downloaded from www.Manualslib.com manuals search engine
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R252 1-216-085-00 METAL CHIP 33K 5% 1/10W R623 1-216-073-00 METAL CHIP 10K 5% 1/10W
R271 1-216-033-00 METAL CHIP 220 5% 1/10W R624 1-216-049-11 RES, CHIP 1K 5% 1/10W
R272 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R631 1-249-383-11 CARBON 1.5 5% 1/6W
R273 1-216-089-00 RES, CHIP 47K 5% 1/10W
R632 1-249-383-11 CARBON 1.5 5% 1/6W
R274 1-216-121-00 RES, CHIP 1M 5% 1/10W R633 1-249-383-11 CARBON 1.5 5% 1/6W
R281 1-216-033-00 METAL CHIP 220 5% 1/10W R634 1-249-383-11 CARBON 1.5 5% 1/6W
R282 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R636 1-216-037-00 METAL CHIP 330 5% 1/10W
R283 1-216-089-00 RES, CHIP 47K 5% 1/10W R641 1-216-097-00 RES, CHIP 100K 5% 1/10W
R284 1-216-121-00 RES, CHIP 1M 5% 1/10W
R642 1-216-113-00 METAL CHIP 470K 5% 1/10W
R301 1-208-812-11 RES, CHIP 18K 2% 1/10W R651 1-216-113-00 METAL CHIP 470K 5% 1/10W
R302 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R652 1-216-097-00 RES, CHIP 100K 5% 1/10W
R303 1-216-077-00 RES, CHIP 15K 5% 1/10W R653 1-208-806-11 RES, CHIP 10K 0.5% 1/10W
R304 1-216-105-00 RES, CHIP 220K 5% 1/10W R654 1-216-073-00 METAL CHIP 10K 5% 1/10W
R305 1-216-001-00 METAL CHIP 10 5% 1/10W
R655 1-216-025-00 RES, CHIP 100 5% 1/10W
R361 1-216-049-11 RES, CHIP 1K 5% 1/10W R656 1-216-025-00 RES, CHIP 100 5% 1/10W
R362 1-249-389-11 CARBON 4.7 5% 1/4W R661 1-249-421-11 CARBON 2.2K 5% 1/4W
R363 1-249-389-11 CARBON 4.7 5% 1/4W R662 1-216-081-00 METAL CHIP 22K 5% 1/10W
R364 1-216-073-00 METAL CHIP 10K 5% 1/10W R663 1-216-089-00 RES, CHIP 47K 5% 1/10W
R365 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
R664 1-216-089-00 RES, CHIP 47K 5% 1/10W
R504 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R683 1-216-089-00 RES, CHIP 47K 5% 1/10W
R505 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R701 1-216-017-00 RES, CHIP 47 5% 1/10W
R506 1-216-057-00 METAL CHIP 2.2K 5% 1/10W (C33R)
R508 1-216-073-00 METAL CHIP 10K 5% 1/10W R702 1-216-073-00 METAL CHIP 10K 5% 1/10W
R509 1-216-097-00 RES, CHIP 100K 5% 1/10W (C33R)
R703 1-216-025-00 RES, CHIP 100 5% 1/10W
R511 1-216-097-00 RES, CHIP 100K 5% 1/10W (C33R)
R512 1-216-097-00 RES, CHIP 100K 5% 1/10W
R518 1-216-097-00 RES, CHIP 100K 5% 1/10W R704 1-216-025-00 RES, CHIP 100 5% 1/10W
R519 1-216-097-00 RES, CHIP 100K 5% 1/10W (C33R)
R520 1-216-097-00 RES, CHIP 100K 5% 1/10W R705 1-216-089-00 RES, CHIP 47K 5% 1/10W
(3100R)
R522 1-216-097-00 RES, CHIP 100K 5% 1/10W R706 1-216-089-00 RES, CHIP 47K 5% 1/10W
R523 1-216-097-00 RES, CHIP 100K 5% 1/10W (3100R)
R524 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R708 1-216-097-00 RES, CHIP 100K 5% 1/10W
R525 1-216-057-00 METAL CHIP 2.2K 5% 1/10W (3100R)
R526 1-216-097-00 RES, CHIP 100K 5% 1/10W R712 1-216-089-00 RES, CHIP 47K 5% 1/10W
(3100R)
R527 1-208-806-11 RES, CHIP 10K 0.5% 1/10W
R529 1-216-073-00 METAL CHIP 10K 5% 1/10W < COMPOSITION CIRCUIT BLOCK >
R535 1-216-097-00 RES, CHIP 100K 5% 1/10W
R536 1-216-097-00 RES, CHIP 100K 5% 1/10W RB601 1-233-413-11 RES, CHIP NETWORK 2.2K (3216)
(C33R: GREEN) RB602 1-233-810-21 RES, NETWORK 100K (3216)
R537 1-216-097-00 RES, CHIP 100K 5% 1/10W RB701 1-233-810-21 RES, NETWORK 100K (3216) (3100R)
(3100R/C33R: AMBER)
< VARIABLE RESISTOR >
R539 1-216-097-00 RES, CHIP 100K 5% 1/10W
R540 1-216-097-00 RES, CHIP 100K 5% 1/10W RV1 1-223-836-11 RES, ADJ, CARBON 220K
R542 1-216-089-00 RES, CHIP 47K 5% 1/10W
R551 1-208-806-11 RES, CHIP 10K 0.5% 1/10W < SWITCH >
R552 1-208-806-11 RES, CHIP 10K 0.5% 1/10W
S501 1-571-478-11 SWITCH, SLIDE (POWER SELECT)
R553 1-216-025-00 RES, CHIP 100 5% 1/10W S503 1-692-431-21 SWITCH, TACTILE (RESET)
R554 1-216-025-00 RES, CHIP 100 5% 1/10W
R555 1-216-097-00 RES, CHIP 100K 5% 1/10W < THERMISTOR >
R556 1-216-097-00 RES, CHIP 100K 5% 1/10W
R558 1-216-025-00 RES, CHIP 100 5% 1/10W TH701 1-801-792-21 THERMISTOR, POSITIVE (C33R)

R559 1-216-025-00 RES, CHIP 100 5% 1/10W < TUNER >

R560 1-216-025-00 RES, CHIP 100 5% 1/10W
R561 1-216-025-00 RES, CHIP 100 5% 1/10W TU1 1-693-440-23 TUNER UNIT (FM/AM TUNER UNIT)
R611 1-216-049-11 RES, CHIP 1K 5% 1/10W
R612 1-216-049-11 RES, CHIP 1K 5% 1/10W < VIBRATOR >

R621 1-216-017-00 RES, CHIP 47 5% 1/10W X1 1-781-246-21 VIBRATOR, CRYSTAL (10.25MHz)

R622 1-216-295-00 SHORT 0 X51 1-579-242-41 VIBRATOR, CRYSTAL (4.332MHz)

43
Downloaded from www.Manualslib.com manuals search engine
 XR-3100R/C33R
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
X501 1-767-833-21 VIBRATOR, CERAMIC (3.68MHz) 3-043-534-41 MANUAL, INSTRUCTION, INSTALL (GERMAN)
X502 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) (C33R: German)
************************************************************** 3-043-535-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH, SWEDISH, PORTUGUESE)
MISCELLANEOUS (3100R: AEP, UK)
************** 3-043-535-21 MANUAL, INSTRUCTION, INSTALL (FRENCH,
GERMAN, DUTCH, ITALIAN, GREEK)
13 1-782-093-11 CORD (WITH CONNECTOR) (ISO-S) (3100R: AEP)
(SPEAKER)
14 1-777-989-21 CORD (WITH CONNECTOR) (AMP REM) 3-043-535-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
(C33R) CZECH, POLISH, TURKISH, RUSSIAN)
15 1-782-092-11 CORD (WITH CONNECTOR) (ISO-P) (POWER) (3100R: South European)
64 1-694-508-11 CONDUCTIVE BOARD, CONNECTION 3-043-535-41 MANUAL, INSTRUCTION, INSTALL (GERMAN)
F801 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A) (3100R: German)
X-3373-412-1 CASE (PANEL) ASSY (for FRONT PANEL)
HP901 1-500-196-21 HEAD, MAGNETIC (PLAYBACK) ************************************************************
LCD901 1-803-497-11 DISPLAY PANEL, LIQUID CRYSTAL
M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL) PARTS FOR INSTALLATION AND CONNECTIONS
************************************************************ **************************************

************** 501 X-3370-077-1 SCREW ASSY (AE. KEY), FITTING

HARDWARE LIST 502 X-3373-600-1 FRAME ASSY
************** 503 1-465-459-21 ADAPTER, ANTENNA
504 1-782-093-11 CORD (WITH CONNECTOR) (ISO-S)
#2 7-685-793-09 SCREW +PTT 2.6X8 (S) (SPEAKER)
#3 7-685-792-09 SCREW +PTT 2.6X6 (S) 505 1-782-092-11 CORD (WITH CONNECTOR) (ISO-P) (POWER)
#4 7-685-795-09 SCREW +PTT 2.6X12 (S)
#5 7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT 506 1-777-989-21 CORD (WITH CONNECTOR) (AMP REM)
#6 7-624-104-04 STOP RING 2.0, TYPE-E (C33R)

#7 7-627-553-17 PRECISION SCREW +P 2X2 TYPE 3

************************************************************ 501
ACCESSORIES & PACKING MATERIALS
********************************

3-043-533-11 MANUAL, INSTRUCTION (ENGLISH, SPANISH, FITTING SCREW BUSHING KEY

×1 ×1 ×1
SWEDISH, PORTUGUESE) (AEP, UK)
3-043-533-21 MANUAL, INSTRUCTION (FRENCH, GERMAN,
DUTCH, ITALIAN, GREEK) (AEP) 502 503 504 SPEAKER CORD
3-043-533-31 MANUAL, INSTRUCTION (GERMAN) (German) ×1
3-043-533-41 MANUAL, INSTRUCTION (ENGLISH, CZECH,
POLISH, TURKISH, RUSSIAN)
(South European)
505
3-043-534-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRAME ASSY ANTENNA ADAPTER POWER CORD
SPANISH, SWEDISH, PORTUGUESE) ×1 ×1 ×1
(C33R: AEP, UK)
C33R
3-043-534-21 MANUAL, INSTRUCTION, INSTALL (FRENCH, 506
GERMAN, DUTCH, ITALIAN, GREEK)
(C33R: AEP)
3-043-534-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
CZECH, POLISH, TURKISH, RUSSIAN) AMP PEM, ATT COARD
×1
(C33R: South European)

9-870-047-11 Sony Corporation

99L057542-1
Mobile Electronics Division Company Printed in Hungary C 1999. 12
44 Published by General Engineering Dept.
Downloaded from www.Manualslib.com manuals search engine