Scribd Logo
Upload

Welcome to Scribd!

  • 148 views

    Top Drive PB169 - Blower - Motor - U-Bolt - Support

    Uploaded by

    JoseMi Vacaflor Illanes
    BLOWER ASSY, 575V, 15HP-ELM PRECAUTION

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Top Drive PB169 - Blower - Motor - U-Bolt - Support

    Uploaded by

    JoseMi Vacaflor Illanes
    148 views6 pages
    BLOWER ASSY, 575V, 15HP-ELM PRECAUTION

    Original Title

    Top Drive PB169 - Blower_Motor_U-Bolt_Support

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    BLOWER ASSY, 575V, 15HP-ELM PRECAUTION

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    148 views6 pages

    Top Drive PB169 - Blower - Motor - U-Bolt - Support

    Uploaded by

    JoseMi Vacaflor Illanes
    BLOWER ASSY, 575V, 15HP-ELM PRECAUTION

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 6

    Model: 1250AC/1275AC

    Jul. 27, 2017


    Serial #: N/A

    Product Bulletin # TDS-169

    Blower Motor U-Bolt Support

    Issue
    During periods of rough drilling, the feet on the E01-1016-030 motor used on the P10576 blower
    could fatigue and crack. This could leave the motor unsecured to the blower baseplate and/or
    cause damage to the impeller.

    Affected Blower
    Blower Part No. Blower Motor Part No.
    P10576 E01-1016-030
    Note: Contact RIGLINE 24/7™ Support to order the U-bolt upgrade kit for blowers other than the
    one listed.

    Recommendation
    Canrig offers a kit that contains additional support to secure the motor to the baseplate and
    reduce the stress on the motor feet, see Table 1 below. This consists of (2) U-bolts which harness
    around the motor to secure to the blower baseplate. Install this kit on rigs that perform rough
    drilling.

    Canrig also recommends the following:

    • Regular inspection of the blower motor for loose or broken components as well as for loose or
    broken fasteners. Inspect weekly under regular drilling conditions. Inspect daily when
    operating in rough drilling conditions.
    • Replace the blower motor if feet are broken or damaged. Replace broken or damaged
    fasteners.

    Table 1: (AY23152) Blower Motor Support U-Bolt Assembly Components


    Item Qty. Part No. Description
    1 1 DT33137 U-BOLT, 1/2-13UNC x 13.38 H x 10.25 ID
    2 1 DT33138 U-BOLT, 1/2-13UNC x 14.38 H x 12.75 ID
    3 4 LN-0500NC-SS LOCKNUT, 1/2-13UNC, GR8, STOVER
    4 10FT M21-2000-010 WIRE ROPE, 1/16 IN, DIA
    5 10 M19-3006-010 FERRULE, 1/16, OVAL, ALUMINUM
    6 2 M15437 CLAMP, SPRING, 1/2 IN OD HOSE, 17-7SS

    RIGLINE 24/7™ Support: 866.433.4345 | International: +1 281.774.5649 | E-mail: [email protected]


    Document ID 17-032 v 1.0 | Copyright © 2017 Canrig Drilling Technology Ltd. All rights reserved.
    1 of 6
    Model: 1250AC/1275AC
    Jul. 27, 2017
    Serial #: N/A

    U-bolt Addition Procedure


    Preliminary Fabrication

    The blower motor mount will require four (4) drilled holes at locations indicated on Figure 1 for
    installation of the U-bolts.

    13.25 [336.6]

    Drilled Holes 6.63 [168.3]

    10.75 [273.1]
    2X 11.00 [279.4]
    5.38 [136.5]

    4X Ø 0.56 [14.3]

    2X 1.75 [44.5]

    ԩ
    Drilled Holes
    Figure 1: Four holes required to mount U-bolts.

    RIGLINE 24/7™ Support: 866.433.4345 | International: +1 281.774.5649 | E-mail: [email protected]


    Document ID 17-032 v 1.0 | Copyright © 2017 Canrig Drilling Technology Ltd. All rights reserved.
    2 of 6
    Model: 1250AC/1275AC
    Jul. 27, 2017
    Serial #: N/A

    Installing U-bolts
    1. Install spring clamps (M15437) on the U-bolts by squeezing the legs with the tool (for example,
    pliers) and position toward the bottom of the U-bolt as shown on Figure 2.

    Spring clamps

    Figure 2: Spring clamps on U-bolts

    RIGLINE 24/7™ Support: 866.433.4345 | International: +1 281.774.5649 | E-mail: [email protected]


    Document ID 17-032 v 1.0 | Copyright © 2017 Canrig Drilling Technology Ltd. All rights reserved.
    3 of 6
    Model: 1250AC/1275AC
    Jul. 27, 2017
    Serial #: N/A

    2. Clamp the front of the blower motor by installing DT33137 U-bolt firmly around the bottom of
    the blower motor and through holes drilled in blower support mount as shown on Figure 3.
    3. Install LN-0500NC-SS locknuts on DT33137, torque to 43 ft-lbs.
    4. Clamp the rear of the blower motor by installing DT33138 U-bolt firmly around the bottom of
    the blower motor and through holes drilled in blower support mount as shown on Figure 3.
    5. Install LN-0500NC-SS locknuts on DT33138, torque to 43 ft-lbs.

    DT33137

    4X LN-0500NC-SS

    DT33138

    Figure 3: Installing and Clamping the Motor U-Bolts

    RIGLINE 24/7™ Support: 866.433.4345 | International: +1 281.774.5649 | E-mail: [email protected]


    Document ID 17-032 v 1.0 | Copyright © 2017 Canrig Drilling Technology Ltd. All rights reserved.
    4 of 6
    Model: 1250AC/1275AC
    Jul. 27, 2017
    Serial #: N/A

    6. Add safety restraint to U-bolts by adding safety wire (M21-2000-010) through drilled holes in
    threaded end of U-bolts DT33137 and DT33138 as shown on Figure 4. Crimp with ferrules
    (M19-3006-010). Ensure minimal slack is in safety wire.

    See Table 1 on page 1 for items.

    4 5

    Figure 4: Safety Wire Restraint on the U-bolts

    RIGLINE 24/7™ Support: 866.433.4345 | International: +1 281.774.5649 | E-mail: [email protected]


    Document ID 17-032 v 1.0 | Copyright © 2017 Canrig Drilling Technology Ltd. All rights reserved.
    5 of 6
    Model: 1250AC/1275AC
    Jul. 27, 2017
    Serial #: N/A

    7. Use tool (for example, pliers) to squeeze the legs and relieve tension on spring clamp on the
    U-bolt.
    8. Connect safety restraint around spring clamp and secure with ferrule, see detail on Figure 5.
    9. Anchor safety restraint to the blower motor mount cut-outs as shown on Figure 5. Ensure
    minimal slack is in safety wire.

    Spring clamp
    Ferrule

    Safety
    Wire

    Spring clamp with safety


    restraint and ferrule

    Figure 5: Safety restraint for U-bolts

    RIGLINE 24/7™ Support: 866.433.4345 | International: +1 281.774.5649 | E-mail: [email protected]


    Document ID 17-032 v 1.0 | Copyright © 2017 Canrig Drilling Technology Ltd. All rights reserved.
    6 of 6

    You might also like