8 7 6 5 4 3 2 1

Ratio Options 1 SAE Clutch Housing Options 2 SAE Clutch Options 3 Pilot Bearing SAE Pump Pad Adapters 5 6 7 SAE Pump Spline Adapters 8 9 10
3PD08 SAE No. Dim. Dim. Bolt Size & Clutch Dim. Dim. Dim. Dim. Bolt Size & Std. Bearing Dim. SAE Bolt Size Bolt Pilot Dim. SAE Teeth
1.40 Dec. A B Qty. No. C D F G Qty. No. E Size & Qty. Circle Dia. H Size & Pitch
1.34 Dec. 1 20.875 20.125 7/16-14 (12) SP214 18.375 17.250 11.12 1.00 (8) 17/32 6407 ZZ 3.9370 A 3/8-16 (2) 4.187 3.25 5.69 A 9T-16/32
D D
1.23 Dec. 2 18.375 17.625 3/8-16 (12) SP211 13.875 13.125 8.25 1.56 (8) 13/32 6307 ZZ 3.1496 B 1/2-13 (2) 5.750 4.00 5.69 B 13T-16/32
1.13 Dec. 3 16.875 16.125 3/8-16 (12) SP114 18.375 17.250 8.25 1.00 (8) 17/32 6207 ZZ 2.8346 B 1/2-13 (4) 5.000 4.00 5.69 BB 15T-16/32
1:1 C111 13.875 13.125 8.25 1.56 (8) 13/32 C 5/8-11 (2) 7.125 5.00 5.69 C 14T-12/24
1.13 Inc. C110 12.375 11.625 8.25 2.12 (8) 13/32 C 1/2-13 (4) 6.375 5.00 5.69 CC 17T-12/24
1.23 Inc. D 3/4-10 (4) 9.000 6.00 5.69 D 13T-8/16
1.34 Inc. D2 3/4-10 (2) 9.000 6.00 5.81 F 15T-8/16
1.40 Inc. 25.00 E 3/4-10 (4) 12.500 6.50 5.81 21 21T-16/32
1.53 Inc. F 1.00-8 (4) 13.781 7.00 6.19 23 23T-16/32
12.50
8 27 27T-16/32

2
1 SEE MODEL DESCRIPTION
5 11
FOR DIPSTICK LOCATION

C C

NAME TAG 12
5/8-11 UNC X 1.00 DEEP
(4) PLCS. BOTH SIDES 3
8.00
4

26.75
2.25
4.50 E D C B A

5.29

B
11.79 B

7 3.50 F G
6 6.00 6.00
H 3.79
9 10
NOTE:
AMWF SEQUENCE NO.

1 OF 1
1) REFER TO ASSEMBLY BOOK FOR ADAPTER MOD DRAWINGS.

SHEET
2) LUBRICATE ALL ORINGS PRIOR TO INSTALLATION.
3) APPLY SILVER STREAK #200S TO EXTERNAL SPLINES OF INPUT SHAFT. ALL DIMENSIONS IN INCHES THIS PRINT IS CONFIDENTIAL AND IS THE PROPERTY OF
4) USE LOCTITE 609 WHEN INSTALLING EXP. PLUG, P/N 012043.
5) USE LOCTITE 609 WHEN INSTALLING DIPSTICK,
PATENT NO. 7,152,711 UNLESS OTHERWISE SPECIFIED:
CASTINGS
ALLOW .12 FINISH STOCK ON
MACHINED SURFACES.
DURST, DIV. REGAL BELOIT CORP.
THIS PRINT SHALL NOT BE USED, COPIED OR REPRODUCED
IN WHOLE OR IN PART, NOR SHALL THE CONTENTS
BE REVEALED IN ANY MANNER TO ANYONE,
DURST
DIVISION OF REGAL-BELOIT CORP.
A A
AND DIPSTICK HOLE PLUG, P/N 012326. 5 30214 DIM "F" FOR SP214 WAS 11.20, OTHER "F" DIMS WERE 8.69 KTS 9/24/10 FILLETS AND RADII .12 MAX. UNLESS WRITTEN PERMISSION IS OBTAINED FROM P.O. BOX 298

6) DO NOT USE LOCTITE ON PUMP PAD SCREWS.

7) TIGHTEN 1/2" SCREWS: 105 FT.LBS.
CAUTION 4
4
27445
27445
ADDED 1.13 RATIOS
ADDED 1.13 RATIOS
KTS
KTS
12/4/07
12/4/07
MACHINING TOLERANCES
.X ` .030
.XX ` .010
.XXX ` .005
FRAC. ` 1/64
ANGLE ` 30'
125 FINISH
MATERIAL
DURST, DIV. REGAL BELOIT CORP.
TITLE
BELOIT, WISCONSIN 53511

REF 8) TIGHTEN 5/8" SCREWS: 210 FT.LBS. Always insure that your powertrain is free of torsional 3 27445 REVISE NOTE 9, ADD PATENT NO. WEM 6/5/07
MODEL WHERE USED
3PD08 CLUTCH
9) OIL MUST MEET API GL-5 SPEC: 80W90, EP90 OR EQUIVALENT. vibrations. DURST is not responsible for damage or 2 25724 UPDATED ITEM NUMBERS NJS 9/24/04 N/A CHARTED DRAWING
failure due to unaddressed torsional vibrations. 1 24560 RELEASED TO PRODUCTION NJS 9/02/04 DRAWN BY DATE SCALE THIRD PART NO. SIZE
10) WHEN ORDERING PARTS REFER TO THE DURST SERVICE MANUAL. REV. W.O. NO. ZONE DESCRIPTION BY DATE NJS 9/01/04 3:8 ANGLE
3PD08C D
PROJECT
8 7 6 5 4 3 2 1