JVC SP Uxg68

MICRO COMPONENT SYSTEM
UX-G68 —Consists of CA-UXG68 and SP-UXG68
SUPER VIDEO
INSTRUCTIONS
GVT0203-006A
[US,UN,UG,UX,A,UW]
Downloaded from www.Manualslib.com manuals search engine
Warnings, Cautions and Others
CAUTION— (Standby/on) button!
Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). When installing the apparatus,
ensure that the plug is easily accessible. The (Standby/on) button in any position does not disconnect the mains line.
• When the System is on standby, the STANDBY lamp lights red.
• When the System is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service
personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these
batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall
be placed on the apparatus.
Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm
or more.
Front view 15 cm Side view 15 cm
15 cm 1 cm 1 cm 15 cm
15 cm
10 cm
SP-UXG68 CA-UXG68 SP-UXG68 CA-UXG68
[European Union only]
G-1
Introduction
Precautions Contents
Installation Introduction ............................................................. 1
• Install the System in a location with adequate ventilation to Playable Disc/File Types .................................................... 2
prevent internal heat build-up in the System. How to Read This Manual .................................................. 2
DO NOT install the System in a location near Connections .............................................................. 3
heat sources, or in a place subject to direct Display Indicators.................................................... 6
sunlight, excessive dust or vibration.
Daily Operations—Playback .................................. 7
• Install in a place which is level, dry and neither too hot nor
too cold—between 5°C and 35°C. Daily Operations—Sound & Other Adjustments ..... 12
• Leave sufficient distance between the System and the TV. Adjusting the Volume ....................................................... 12
• Keep the speakers away from the TV to avoid interference Adjusting the Sound.......................................................... 12
with the TV. Creating 3-dimensional Sound Field—3D Phonic............ 13
Power sources Using Headphone Surround .............................................. 13
• When unplugging the System from the wall outlet, always Presetting Automatic DVD Video Sound Increase Level........ 13
pull on the plug, not the AC power cord. Changing the Display Brightness...................................... 13
Adjusting the Audio Input Level ...................................... 14
DO NOT handle the AC power cord with wet Changing the Scanning Mode ........................................... 14
hands. Changing the Picture Tone................................................ 14
Setting the Clock............................................................... 15
Moisture condensation Turning Off the Power Automatically .............................. 15
Moisture may condense on the lenses inside the System in
the following cases:
Unique DVD/VCD Operations ............................. 16
• After starting to heat the room Selecting the Audio Track................................................. 16
• In a damp room Selecting the Subtitle Language........................................ 17
• If the System is brought directly from a cold to a warm Selecting the View Angle ................................................. 17
place. Selecting the Browsable Still Pictures .............................. 17
Should this occur, the System may malfunction. In this case, Playing Back Bonus Group............................................... 17
leave the System turned on for a few hours until the moisture Making Dialogues Clear—Clear Voice ............................ 18
evaporates, unplug the AC power cord, then plug it in again. Special Effect Playback .................................................... 18
Internal heat Advanced Playback Operations ........................... 19
• Make sure there is good ventilation around the unit. Poor Programming the Playing Order—Program Play ............. 19
ventilation could overheat and damage the unit. Playing at Random—Random Play .................................. 20
DO NOT block the ventilation openings or Playing Repeatedly ........................................................... 21
holes. If they are blocked by a newspaper or Prohibiting Disc Ejection—Child Lock ............................ 21
cloth, etc., the heat may not be able to get out. On-screen Bar Operations ................................................. 22
Others Audio/Video File Operations ................................ 26

• Should any metallic object or liquid fall into the System, Advanced Tape Operations .................................. 28
unplug the AC power cord and consult your dealer before Recording on a Tape ......................................................... 28
operating any further. Synchronized Recording ................................................... 29
DO NOT disassemble the System since there Enjoying Karaoke.................................................. 30
are no user serviceable parts inside. Singing Along (Karaoke) .................................................. 30
Microphone Mixing .......................................................... 31
• If you are not going to operate the System for an extended Reserving Karaoke Songs—Karaoke Program Play......... 32
period of time, unplug the AC power cord from the wall Timer Operations .................................................. 33
outlet.
If anything goes wrong, unplug the AC power cord and Setup Menu Operations ........................................ 35
consult your dealer. Additional Information ......................................... 37
Learning More about This System.................................... 37
Troubleshooting ................................................................ 41
Operating JVC’s TVs Using the Remote Control............. 43
Specifications .................................................................... 44
Parts Index ............................................................ 45
1
When playing a multi-channel encoded DVDs, the System
Playable Disc/File Types properly converts these multi-channel signals into 2
channels, and emits the downmixed sound from the
speakers.
• To enjoy the powerful sound of these multi-channel
encoded DVDs, connect a proper decoder or an amplifier
with a proper built-in decoder to the OPTICAL DIGITAL
COMPACT
OUT terminal on the rear.
DIGITAL VIDEO SUPER VIDEO DIGITAL AUDIO IMPORTANT: Before playing a disc, make sure of
the following...
• CD-R/-RW: Recorded in the Audio CD, Video CD, and • Turn on the TV and select an appropriate input mode on
SVCD formats. MP3, WMA, WAV, JPEG, MPEG-1, the TV to view the pictures or on-screen displays.
MPEG-2, ASF, and DivX files written in accordance • For disc playback, you can change the initial setting to
with the “ISO 9660” format can also be played. your preference. See “Setup Menu Operations” on
• DVD-R/-RW, +R/+RW: Recorded in the DVD Video page 35.
format. MP3, WMA, WAV, JPEG, MPEG-1, MPEG-2, If “ ” appears on the TV screen when you press a
ASF and DivX files written in the UDF-Bridge format button, the disc cannot perform the operation you have
can also be played. tried to do.
• DVD-R/-RW: Recorded in the DVD Video Recording
(VR) format.
• DVD-ROM: Recorded in the MP3, WMA, WAV, JPEG, How to Read This Manual
MPEG-1, MPEG-2, ASF, and DivX format. • Button and control operations are explained in the table
• USB mass storage class device: MP3, WMA, WAV, below.
JPEG, MPEG-1, MPEG-2, ASF and DivX files. • Some related tips and notes are explained later in the
sections “Learning More about This System” and
In addition to the above discs/files, this System can playback
“Troubleshooting,” but not in the same section
audio data recorded on CD-Extra.
explaining the operations ( INFO indicates that the
• The following discs cannot be played back:
content has some information).
DVD-RAM, CD-I (CD-I Ready), CD-ROM, Photo CD,
CD-G (CD-Graphics) and DVD/CD Text. Indicates that you press the button briefly.
Playing back these discs will generate noise and damage
the speakers.
• In this manual, “file” and “track” are interchangeably used Indicates that you press the button briefly and
for MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/ repeatedly until an option you want is
DivX operations. selected.
• It is possible to playback finalized +R/+RW (DVD format Indicates that you press one of the buttons.
only) discs. “DVD” lights on the front display panel when
a +R/+RW disc is loaded.
About color system 2 sec. Indicates that you press and hold the button
This System accommodates the NTSC and PAL system and for a specified period.
can playback discs recorded in either the NTSC or the PAL
system.
• To change the color system, see page 14. Indicates that you turn the control toward the
Note on Region Code specified direction(s).
DVD players and DVDs have their own Region Code
numbers. This System can playback only DVDs with an Remote Indicates that this operation is only possible
appropriate Region Code number.
ONLY
using the remote control.
• For details, see “Specifications” on page 44. Indicates that this operation is only possible
EX.: Main Unit
ONLY
using the main unit.
“DVD Logo” is a trademark of DVD Format/Logo

(For Central and South American countries and Australia) Licensing Corporation registered in the US, Japan and other
countries.
Audio formats
The System can playback the following digital audio Caution for DualDisc playback
formats. The Non-DVD side of a “DualDisc” does not comply with
• LPCM (Linear PCM), DIGITAL (Dolby Digital), the “Compact Disc Digital Audio” standard. Therefore, the
DTS (Digital Theater Systems), MLP (Meridian Lossless use of the Non-DVD side of a DualDisc in this product is not
Packing) recommended.
2
Connections
Do not connect the AC power cord until all other Supplied accessories
connections have been made. Check to be sure that you have all the following items.
• FM antenna (x1)
• Connect VIDEO OUT directly to the video input of your • AM loop antenna (x1)
TV. Connecting VIDEO OUT to a TV via a VCR may • Composite video cord (x1)
interfere with your viewing when playing back a copy- • Remote control (x1)
protected disc. Connecting VIDEO OUT to an integrated • Batteries (x2)
TV/VCR system may also interfere with your viewing. • AC plug adapter (x1) (except for the Middle East and
Australia)
If any item is missing, consult your dealer immediately.
Rear panel
~ From AM/FM antenna

See page 4.
Ÿ From the speakers

See page 4.
! From the powered subwoofer

See page 4.
From the input of TV/monitor

See page 5.
GE
VOLTATOR
Voltage selector (except for Australia)
SELEC See page 5.
110V 127V
230V
V
-240
220V
@ From the digital input of digital
audio component
See page 5.
¤ To a wall outlet
Plug in the AC power cord only after
all connections are completed.
Front panel • If the wall outlet does not match the
Pull down the cover until you hear a clicking sound. AC plug, use the supplied AC plug
adapter (except for the Middle East
and Australia).
From the portable audio device

See page 5.
From the USB mass storage class device
From the headphones See page 5.
See page 7.
3
~ AM/FM antenna Ÿ Speakers
To assemble the AM loop antenna • When connecting the speaker cords, match the polarity of
the speaker terminals: red color to (+) and black color to (–).
Press and hold
To connect AM/FM antenna
AM loop antenna
(supplied)
Insert Release
Red
From right
CAUTION: Black From left
speaker
speaker
FM antenna (supplied)
• DO NOT connect more than one speaker to
Extend it so that you can obtain the best each terminal.
reception. • DO NOT push or pull the speakers as this
will damage the foot spacers at the bottom
of the speakers.
For better FM reception
! To connect the powered subwoofer

FM outdoor antenna SUBWOOFER
OUT
(not supplied) From the powered
subwoofer
(not supplied)
The subwoofer connected can reproduce the bass sounds

recorded in front left and right channels, but cannot
reproduce the LFE signals in DVD multi-channel discs.
• Disconnect the supplied FM antenna, and connect to an • Before plugging the unit to the main supply, make sure that
outdoor FM antenna using a 75 Ω wire with coaxial type the powered subwoofer is turned off.
connector (IEC or DIN45325).
4
TV/monitor • If an external device is not equipped with a stereo mini plug
audio output, use a plug adaptor to convert the stereo mini
Connect the COMPONENT, S-VIDEO, or VIDEO jacks plug to the corresponding plug of the audio output.
which you want to use.
When connecting a USB mass storage class device
Red
USB cable At the front
(not supplied) panel
Blue
Green Component video cord • You can connect a USB mass storage class device such as a
(not supplied) USB flash memory device, hard disk drive, multimedia card
• To select progressive scanning mode (see page 14), use reader, etc. to this System. See pages 10 and 37 for details.
COMPONENT jacks. • If you press USB MEMORY 3, the System detects the
USB mass storage class device and the control screen
appears on the TV screen. See page 26 for details.
• You cannot connect a computer to the USB MEMORY
Composite video cord (supplied) terminal of the System.
Before plugging in the System

(except for Australia)
Set the correct voltage for your area with the voltage selector
on the rear.
S-Video cord (not supplied) VOLTAGE
Use a screwdriver to set the voltage
SELECTOR selector to the same voltage as
• After connecting a TV, select the proper video signal mode where you are plugging in the unit.
according to the connection method. See “Changing the 110V (See also the back cover page.)
Scanning Mode” on page 14. 127V
@ Digital audio component 220V 230V

-240V
Protective cap Preparing the remote control
• Set “DIGITAL AUDIO OUTPUT” in the “AUDIO” menu

correctly according to the connected digital audio
equipment (see page 36). If the setting is incorrect, loud
noise may be generated causing damage to the speakers.
When connecting a portable audio device (AUX) R6(SUM-3)/AA(15F)
Stereo mini plug At the front • Dispose of batteries in the proper manner, according to
(not supplied) panel federal, state, and local regulations.
DO NOT recharge, short, disassemble, heat

the battery or dispose of it in a fire.
When using the remote control

• By using QP Link (Quick Portable Link), you can easily
Point the top of the remote control toward the remote sensor
start playing back a portable audio device on this unit. See
as directly as possible. If you operate it from a diagonal
page 11 for details.
position, the operating range (approx. 5 m) may be shorter.
5
Display Indicators
The indications on the display tell you a lot of things while you are operating the System.
Before operating the System, be familiar with when and how the indicator illuminates on the display.
1 2 3 4 5 6 7 8
QPLink S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM

S.TURBO AHB PRO USB MIC V.MASK C.VOICE PG PL ST MONO
PRGR. B.S.P. BONUS PRGM RND 1 TA NEWS INFO 12 3
REC
SLEEP
A.STBY
REC
9 p q w e rt y u i o ;as
1 QP Link (Quick Portable Link) indicator e AHB PRO indicator

• Lights when QP Link is activated. • Lights when Active Hyper Bass Pro is activated.
2 Disc format indicators r BONUS indicator
• SVCD: lights when playing back an SVCD. • Lights when a DVD Audio disc with a bonus group is
• VCD: lights when playing back a VCD. detected.
• CD: lights when playing back a CD. t USB indicator
• DVD: lights when playing back a DVD. • Lights when “USB MEMORY” is selected as the source.
3 Audio file format indicators y Playback mode indicators
• MP3: lights when an MP3 track is detected. • PRGM: lights when Program Play is activated.
• WMA: lights when a WMA track is detected. • RND: lights when Random Play is activated.
4 3D PHONIC indicator • (repeat)1:
• Lights when 3D Phonic is activated. – 1 : lights when One Track/Chapter/Step Repeat is
• Lights when HP Surround is activated. activated.
5 C.VOICE (Clear Voice) indicator – : lights when One Group/Title/All Tracks Repeat is
• Lights when Clear Voice is activated. activated.
6 PG/PL indicators u Indicators for Karaoke function
• PG: lights when a DVD-VR formatted disc is called up. • MIC: lights when the microphone is connected.
• PL: lights when a Play List recorded on a DVD-VR • V.MASK (Voice Mask): lights when Voice Mask is
formatted disc is called up. activated.
7 Radio band indicators i A.STBY (Auto Standby) indicator
• AM: lights when tuning in to an AM station. • Lights when Auto Standby is activated.
• FM: lights when tuning in to an FM station. • Flashes when disc playback stops with Auto Standby
8 FM reception indicators activated.
• ST (stereo): lights while an FM stereo station with o REC indicator
sufficient signal strength is tuned in. • Lights while recording.
• MONO: lights while receiving an FM stereo station in ; 23 (tape direction) indicators
monaural. – Lights to indicate the current tape running direction.
9 S.TURBO (Sound Turbo) indicator – Flashes slowly during playback and recording.
• Lights when Sound Turbo II is activated. – Flashes quickly while rewinding a tape.
p PRGR. (Progressive) indicator a SLEEP indicator
• Lights when the progressive scanning mode is selected. • Lights when the Sleep Timer is activated.
q Main display s Daily Timer indicators
• While listening to radio: band (or preset number) and • : lights when Daily Timer is on standby or is being set;
station frequency appear. flashes while is working.
• While selecting “AUX”: “AUX” appears. • 1/2/3: lights when a Daily Timer (1, 2, or 3) is on standby
• While playing a disc or file: current status appears. or is working; flashes while being set.
• While selecting “TAPE”: “TAPE” appears. • REC: lights when the Recording Timer is on standby or
w B.S.P. (Browsable Still Picture) indicator is working; flashes while being set.
• Lights when Browsable Still Pictures are detected while
playing a DVD Audio disc.
6
Daily Operations—Playback
Remote control In this manual, operations using the remote control are
mainly explained; however, you can use the buttons
and controls on the main unit if they have the same (or
similar) name and marks.
Number
buttons
1
1 Turn on the power.
RETURN The STANDBY lamp on the main unit turns off.
ENTER/SET • Without pressing AUDIO, the System turns on
TOP MENU/PG MENU/PL by pressing one of the source buttons.
, , ,
• The System turns on and activates the AUX source
by starting playback on an external device when QP
2 GROUP/TITLE
Link is activated. (See page 11 for details.)
8
1,y
7
GROUP/TITLE SKIP
2 Select the source.
4,x Playback automatically starts if the selected source is
QP LINK FM/PLAY MODE ready.
• If you press AUX, start playback on the external
SHIFT 3 component.
3 Adjust the volume.
4 Operate the target source as explained
later.
To turn off (standby) the unit
1 The STANDBY lamp on the main unit
lights in red.
• A small amount of power is always
consumed even while on standby.
You can reduce power consumption by pressing DIMMER

2 USB FM/AM (while holding SHIFT) to turn the display off while on
DVD/CD MEMORY TAPE /AUX standby.
• When the display is turned off, QP Link does not work.
For private listening

Connect a pair of headphones to the PHONES jack on the
main unit. The sound will no longer come out of the
3 QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM F
S.TURBO AHB PRO USB MIC V.MASK C.VOICE PG PL S
speakers. Be sure to turn down the volume before
connecting or putting on the headphones.
PRGR. B.S.P. BONUS PRGM RND 1 TA NEWS INFO
• Disconnecting the headphones will activate the
speakers again.
TV VOL
AUDIO VOL
DO NOT turn off (standby) the System with

the volume set to an extremely high level;
4 otherwise, the sudden blast of sound may
damage your hearing, speakers and/or
headphones when you turn on the System or
start playback.
7
Listening to the Radio INFO To select the band (FM or AM)
Remote control: Main unit:
Main Unit
ONLY FM/AM
To set the AM tuner interval spacing /AUX FM/AM
/AUX
Before operating the tuner, it is required to select the
appropriate AM space interval used for your area.
• This is possible only while the System is on standby.
1 Select the AM band. To tune in to a station

While FM or AM is selected...
FM/AM FM AM Remote control: Main unit:
/AUX
AUX 2 sec. 2 sec.
GROUP/TITLE SKIP DOWN UP
2 Turn off the power.
Frequency starts changing on the display.

When a station (frequency) with sufficient signal strength is
tuned in, the frequency stops changing.
3 Select the appropriate AM space interval for your • When you repeatedly press the button, the frequency
area. changes step by step.
To stop searching manually, press either button.
Remote
ONLY
7 If the FM station has poor reception
DVD/CD
3/8 FM/PLAY
MODE
AM 9KHZ
(9 kHz interval)
(while holding...)
The MONO indicator lights on the display. Reception will
improve though stereo effect is lost—Monaural reception.
To restore the stereo effect, press the button again (the
7 MONO indicator disappears).
DISPLAY
Remote
ONLY
AM 10KHZ To preset the stations
(10 kHz interval) You can preset 30 FM and 15 AM stations.
(while holding...)
1 Tune in to a station you want to preset.
• You can also store the monaural reception mode for
FM preset stations if selected.
2 Activate the preset number entry mode.
ENTER/SET QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
REC
SLEEP
A.STBY
REC
• Finish the following process while the indication on

the display is flashing.
8
3 Select a preset number for the station you store.
Playing Back a Tape
Examples:
1 2 3 To select preset number 5, To insert a tape
press 5. You can playback type I tapes.
4 5 6 To select preset number 10, Push Insert Close
press 10.
7 8 9 To select preset number 15,
press 10, 1, then 5.
• You can also use the y or 1 button.

With the tape side facing outside
4 Store the station.
ENTER/SET QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
To start: To stop:
REC
SLEEP
A.STBY
REC
Remote
ONLY
To tune in to a preset station
When “TAPE” is not selected as the
1 Select the band (FM or AM). current source, press twice.
To rewind/fast-forward the tape:

FM/AM
/AUX
FM AM Remote control:
GROUP/TITLE SKIP
AUX Fast-forward the tape.
2 Select the preset number for the station you stored. Rewind the tape.
Examples: Main unit:

1 2 3 To select preset number 5, DOWN
press 5. Rewind the tape.

press 10.
UP
10 0 10 To select preset number 30, Fast-forward the tape.
• You can also use the y or 1 button.
9
Playing Back a Disc/File INFO On-screen guide icons
• During playback, the following icons may appear on the
Before operating a disc/file, be familiar how a disc/file is TV:
recorded.
• DVD Video comprises of “Titles” which includes At the beginning of a scene containing
“Chapters,” DVD Audio/MP3/WMA/WAV/MPEG-1/ multi-angle views.
MPEG-2/ASF/DivX comprises of “Groups” which At the beginning of a scene containing
includes “Tracks,” JPEG comprises of “Groups” which multi-audio sounds.
includes “Files,” and CD/SVCD/VCD comprises of only At the beginning of a scene containing
“Tracks.” multi-subtitles.
• For playback of MP3/WMA/WAV/JPEG/MPEG-1/ • The following icons will be also shown on the TV to
MPEG-2/ASF/DivX files in a USB mass storage class indicate your current operation.
device, see also page 26. , , , , ,
To insert a disc • To deactivate the on-screen guide icons, see “ON
You can insert a disc while playing another source. SCREEN GUIDE” in “OTHERS” menu on page 36.
Remote
ONLY
To select a title/group
While playing a disc/file...
GROUP/TITLE SKIP
• When using an 8 cm disc, place it on the inner circle of the

disc tray.
To close the disc tray, press 0 again. (while holding...)
• If you press DVD/CD 3, disc tray closes automatically
and playback starts (depending on how the disc is • You can select a title/group directly by pressing a number
programmed internally). button after pressing GROUP/TITLE (except for DVD-VR
disc).
To connect a USB mass storage class device • Group name appears for MP3/WMA/WAV playback.
You can connect a USB mass storage class device
(see page 5) while playing another source. To select a chapter/track
• If you press USB MEMORY 3, the System detects the • For VCD/SVCD, cancel PBC (see next page).
USB mass storage class device, the control screen appears While playing a disc/file...
on the TV screen, and playback starts. • First time you press 4, you
GROUP/TITLE SKIP
• To disconnect the USB mass storage class device safely, will go back to the beginning of
disconnect the device after turning the System off. the current chapter/track.
To playback a disc/file
To start: To pause: To stop: Remote
ONLY
To locate a particular portion
DVD/CD USB While playing a disc/file...
USB – SLOW +
DVD/CD MEMORY x2 x5 x10 x20 x60
To release, press
DVD/CD 3 or x2 x5 x10 x20 x60
USB MEMORY 3.
• While playing a disc/file: This System can store the stop • Search speed changes as illustrated above except for MP3/
point, and when you start playback again by pressing WMA/WAV/DivX discs/files. For MP3/WMA/WAV/
DVD/CD 3 or USB MEMORY 3 (even while on DivX discs/files, search speed and the indications on the
standby), it starts from the position where you have TV are different.
stopped—Resume Play. (“RESUME” appears on the • No sound comes out if searching is carried out while
display when you stop playback.) showing the moving picture.
To stop completely while Resume is activated, press 7 To return to normal playback, press DVD/CD 3 or USB
MEMORY 3 (depending on the source type).
twice. (To cancel Resume, see “RESUME” on page 36.)
• When operating the System, the on-screen guide icon (see
the following table) appears on the TV.
10
• For DivX, each time you press the > or < button, you can To move to the next or previous page of the current
skip to a scene for 30 seconds or 5 minutes depending on menu:
the DivX file.
GROUP/TITLE SKIP
Moves to the next page.
Moves to the previous page.
To return to the previous menu:

Remote
ONLY
To locate an item directly
You can select a title/chapter/track directly and start
playback. RETURN
• For DVD Video, you can select a title before starting
10
playback, while you can select a chapter after starting
playback.
Examples:
1 2 3 To select number 5, press 5. (while holding...)
To select number 10, press 10.
4 5 6
To select number 15, press 10, To cancel PBC, press 7, then select a track. Playback starts
8 9
1, then 5. with the selected track.
7
To select number 30, press 10, To reactivate PBC, press 7 (twice if Resume is turned
10 0 10 3, then 0. “ON”), then press DVD/CD 3.
Playing Back a
Remote
Remote
ONLY Portable Audio Device ONLY INFO
To playback using the disc menu By using QP Link (Quick Portable Link), you can easily start
7 For DVD Video/DVD Audio: playing back a portable audio device connected to the AUX
1 Show the disc menu. jack.
• Make sure to set the volume of your portable audio device
TOP MENU/PG MENU/PL
loud enough so that the System can detect the sound signal.
To activate QP Link
AHB PRO
2 Select an item on the disc menu. QP LINK
TV CH
QPL ON
(Initial setting)
ENTER/SET
QPL OFF
When QP Link is activated, connecting a portable device to
the AUX jack and starting playback performs the following:
TV CH
• While listening to another source...
Changes the source to AUX automatically. (If you change
• With some discs, you can also select items by entering the from AUX to another source, QP Link will be canceled.)
number using the number buttons. • While the System is on standby...
Turns on the System and activates the AUX source
7 For SVCD/VCD with PBC: automatically (except when the display is turned off).
While playing a disc with PBC, “PBC” appears on the
display.
QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
When disc menu appears on the TV, select an item on the REC
SLEEP
menu. Playback of the selected item starts.

A.STBY Bubbles appear when
REC QP Link works.
Examples:
1 2 3 To select number 5, press 5.
To select number 10, press 10. While QP Link plays back the device...
4 5 6
To select number 15, press 10, QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
1, then 5.
REC
SLEEP
Bubbles disappear
7 8 9
To select number 30, press 10,
A.STBY when the sound signal
REC stops or is too weak.
10 0 10 3, then 0.
11
Daily Operations—Sound & Other Adjustments
Adjusting the Volume
Remote control
You can adjust the volume level from VOL MIN to level 40
(VOL MAX).
DIMMER
3D PHONIC SLEEP Remote control: Main unit:
A.STANDBY VOLUME
CLOCK/TIMER
SCAN MODE
VFP
TV VOL
CANCEL DISPLAY AUDIO VOL
, , ,
ENTER/SET Remote
ONLY
To drop the volume in a moment
FADE To restore the volume, press again, or
MUTING adjust the volume level.
AHB PRO
DVD/AUX BASS/TREBLE
LEVEL AUDIO VOL
+,–
SHIFT Adjusting the Sound INFO
SOUND FADE
TURBO MUTING To reinforce the heavy sound
This boosts the low and high frequency sound—Sound
Turbo II.
SOUND
TURBO
Main unit TURBO ON
TURBOOFF
• When Sound Turbo II is turned on, AHB Pro is
automatically turned on, and cannot be turned off.
(AHB PRO indicator does not light even though the
function is turned on.)
Remote
ONLY
To reinforce the bass sound
While Sound Turbo II is off, the richness and fullness of the
bass sound is clearly maintained regardless of how you set
the volume—Active Hyper Bass Pro.
3D PHONIC/ AHB PRO
SOUND
HP SURROUND QP LINK AHB ON
TURBO
VOLUME +,– AHB OFF

(while holding...)
• When Sound Turbo II is turned on, AHB Pro setting cannot
be changed.
12
Remote
To adjust the tone ONLY

While playing a disc...
You can adjust the bass and treble level from –3 to +3. Remote control: Main unit:
To adjust the bass
3D PHONIC
BASS/
TREBLE BASS TREBLE 4
Canceled
TV VOL
AUDIO VOL (while holding...)
To adjust the treble
BASS/
SURR ON
TREBLE BASS TREBLE
SURR OFF
Canceled
SURR ON Creates a dynamic sound through the headphones.
TV VOL
AUDIO VOL
• If you plug in the headphones while 3D Phonic is activated,
Headphone Surround turns to SURR ON automatically.
Creating 3-dimensional Sound Field • When 3D Phonic is OFF and Headphone Surround is SURR
ON, unplugging the headphones turns 3D Phonic to ACTION.
—3D Phonic
• This does not function for MPEG-1/MPEG-2/ASF/DivX Presetting Automatic DVD Video Sound
discs. Remote
Increase Level ONLY
While playing a disc... DVD Video sound is sometimes recorded at a lower level
Remote control: Main unit: than other discs and sources. You can set the increase level
for the currently loaded DVD Video, so you do not have to
adjust the volume when you change the source.
3D PHONIC
• This only functions for DVD Video and DVD-VR format disc.
4 DVD/AUX
LEVEL NORMAL MIDDLE
(while holding...)
HIGH
3D PHONIC ACTION 3D PHONIC DRAMA

NORMAL Original recording level.
OFF THEATER
MIDDLE Output level is increased (less than “HIGH”).
3D PHONIC 3D PHONIC
HIGH Output level is increased (more than
“MIDDLE”). (initial setting)
ACTION Suitable for action movies and sports
programs.
Remote
DRAMA Creates natural and warm sound. Enjoy Changing the Display Brightness ONLY
movies in a relaxed mood. You can dim the display window.

THEATER Enjoy sound effects like in a major theater.
DIMMER DIM OFF DIM ON
(Canceled)
Using Headphone Surround 1
AUTO DIM
You can enjoy a surround effect while listening through
headphones. (while holding...)
• This only functions for disc/USB mass storage class device DIM ON Dims the display.
playback.
• This does not function for MPEG-1/MPEG-2/ASF/DivX AUTO DIM* Removes the display illumination when
discs. starting playback a disc with a video source.
• The display illuminates when playback
stops.
* “AUTO DIM” does not work for CD/MP3/WMA/WAV.
13
Remote Remote
Adjusting the Audio Input Level ONLY
Changing the Picture Tone ONLY
If the sound from the component connected to the • While showing a playback picture on the TV, you can
AUX jack is too loud or is too quiet when changing from select a preset picture tone, or adjust it and store your own
another source to “AUX,” you can change the audio input taste.
level through the AUX jack (without changing the volume To select a preset picture tone
level).
While the “AUX” is selected as a source...
1 While playing, display VFP setting screen.
NORMAL
DVD/AUX GAMMA 0
LEVEL VFP
AUX LVL1 AUX LVL2 BRIGHTNESS 0
10 CONTRAST 0
AUX LVL3 SATURATION 0
TINT 0
SHARPNESS 0
AUX LVL1 Select this when the sound is too loud with
(while holding...)
“AUX LVL2” selected. This setting is On the TV
recommended for listening and recording 2 Select a preset picture tone.
when connecting an audio device other than a
portable audio device to the AUX jack. NORMAL CINEMA
AUX LVL2 Select this when the sound is too loud with USER2 USER1
“AUX LVL3” selected.
AUX LVL3 Select this when listening to a portable audio
device or recording the sound from it (initial
setting). NORMAL Normally select this.
CINEMA Suitable for a movie source.
USER1/USER2 You can adjust parameters and can
Changing the Scanning Mode Remote
ONLY
INFO store the settings.
Select the color system and the video signal mode according To remove the screen, press VFP again while holding
to the type of your TV. If you connect a progressive TV to SHIFT.
the System through the COMPONENT jacks, you can enjoy
a high quality picture from the built-in DVD player by To adjust the picture tone
selecting “PAL PRG” or “NTSC PRG.”
1 Select “USER1” or “USER2.”
• Follow steps 1 and 2 explained above.
SCAN MODE 2 Select a parameter you want to adjust.
9 PAL PAL PRG
TV CH
NTSC PRG NTSC
ENTER/SET
TV CH
(while holding...)
ENTER/SET
GAMMA Adjust if the neutral color is bright or

dark (–3 to +3).
PAL Select for a conventional PAL TV. BRIGHTNESS Adjust if the entire picture is bright
or dark (–8 to +8).
PAL PRG Select for a progressive PAL TV.
Select to enjoy a progressive scanned CONTRAST Adjust if the far and near positions
picture with a progressive PAL TV. are unnatural (–7 to +7).
NTSC Select for a conventional NTSC TV. SATURATION Adjust if the picture is whitish or
blackish (–7 to +7).
NTSC PRG Select for a progressive NTSC TV.
Select to enjoy a progressive scanned TINT Adjust if the human skin color is
picture with a progressive NTSC TV. unnatural (–7 to +7).
SHARPNESS Adjust if the picture is indistinct
(–8 to +8).
14
3 Adjust the parameter. * Only when the source is DVD/CD.
TV CH ** DVD-VR: Program number/play list number and chapter
ENTER/SET number.
DVD Audio/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/
ASF/DivX: Group and track/file number.
TV CH DVD Video: Title and chapter number.
Remote
4 Repeat steps 2 to 3 to adjust other parameters. Turning Off the Power Automatically ONLY
To erase the screen, press VFP again while holding SHIFT. Auto Standby
Remote
Setting the Clock ONLY INFO A.STANDBY
On
3
Without setting the built-in clock, you cannot use Daily Canceled
Timers (see page 33).
• To exit from setting the clock, press CLOCK/TIMER
(while holding SHIFT) as required. (while holding...)
• To correct a mis-entry during the process, press CANCEL When Auto Standby is in use, the A.STBY indicator lights
(while holding SHIFT) or CLOCK/TIMER (while holding on the display.
SHIFT). You can return to the previous step. When disc play stops, the A.STBY indicator starts flashing.
If no operation is done for about 3 minutes while the
1 Activate the clock setting mode. indicator is flashing, the System turns off (standby)
automatically.
D V D MP3 WMA 3DPHONIC L-
CLOCK/TIMER B PRO USB MIC V.MASK C.VO
BONUS PRGM RND 1 TA
6 Sleep Timer
You can set the shut-off time so that you can go to bed
without turning it off yourself.
(while holding...) 1 Specify the time (in minutes).
• If you have already adjusted the clock before, press the
button repeatedly until the clock setting mode is SLEEP
selected. 2
2 Set the time.
• Adjust the hour, then the minute.
(while holding...)
ENTER/SET
10 20 30 60 90 120 150 180
Canceled
2 Wait until the set time disappears.
REC
SLEEP
To check the time remaining until the shut-off time, press
A.STBY
SLEEP while holding SHIFT.
REC
• If you press the button repeatedly, you can change
Now the built-in clock starts working. the shut-off time.
To check the current clock time during play

Ex.: While playing a disc...
DISPLAY Source information Disc/file type*
Clock Title and chapter
number**
15
Unique DVD/VCD Operations
Remote
Selecting the Audio Track ONLY INFO
Remote control
For DVD Video/DivX: While playing back a chapter
containing audio languages, you can select the language to
listen to.
For DVD Audio: While playing back a track containing
Number audio channels, you can select the audio channel to listen to.
buttons For DVD-VR and SVCD/VCD: When playing back a track,
you can select the audio channel to play.
C.VOICE • You can also select the audio track using the on-screen bar
ZOOM (see page 22).
ANGLE AUDIO/MPX
, , ,
ENTER
/SET While playing a DVD Video...
DVD/CD 3 7 Ex.:
8
1/3 2/3 3/3
SLOW ,
AUDIO/MPX PAGE ENGLISH FRENCH JAPANESE
SUBTITLE
SHIFT 1/3
ENGLISH
2/3
FRENCH
3/3
JAPANESE
While playing a DVD Audio/DivX...

Ex.:
1/3 2/3 3/3
1 2 3
While playing a DVD-VR, or SVCD/VCD...

SVCD
AUDIO/MPX ST1 ST2 L1
R2 L2 R1
DVD-VR/VCD
ST L R
ST1/ST2/ To listen to normal stereo (2-channel)

ST playback.
L1/L2/L To listen to the left audio channel.
R1/R2/R To listen to the right audio channel.
• SVCD can have 4 audio channels. SVCD usually uses
these 4 channels to record two 2-channel recordings (ST1/
ST2).
16
Remote Remote
Selecting the Subtitle Language ONLY
Selecting the View Angle ONLY
For DVD Video/DivX: While playing back a chapter For DVD Video only: While playing back a chapter
containing subtitles in different languages, you can select the containing multi-view angles, you can view the same scene
subtitle language to display on the TV. from different angles.
For DVD-VR: While playing, you can turn the subtitles on • You can also select the multi-view angles using the on-
or off. screen bar (see page 22).
For SVCD: While playing, you can select the subtitles even While playing...
if no subtitles are recorded on the disc.
• You can also select the subtitle language using the ANGLE
on-screen bar (see page 22).
8
While playing a DVD Video/DivX...
1
1/3 (while holding...)
1/3 ENGLISH
SUBTITLE
Ex.: 1/3 2/3 3/3
ENGLISH
1 2 3
1/3 2/3 3/3
1 2 3
2
TV CH
Remote
TV CH
Selecting the Browsable Still Pictures ONLY
For DVD Audio only: While playing back a track linked to

Ex.: browsable still pictures (B.S.P.), you can select the still
picture (turn the page) to be shown on the TV screen.
1/3 2/3 3/3
• If a track is linked to browsable still pictures (B.S.P.), they
are usually shown automatically during playback.
ENGLISH FRENCH JAPANESE • You can also select the page using the on-screen bar (see
page 25).
1/3 2/3 3/3 Each time you press
the button (while
ENGLISH FRENCH JAPANESE
PAGE
SUBTITLE holding SHIFT), the
still picture changes
one after another (if
available).
While playing a DVD-VR... (while holding...)
SUBTITLE Playing Back Bonus Group Remote

ONLY
ON OFF
ON
For DVD Audio only: Some DVD Audio discs have a
OFF
special group called “bonus group” whose contents are not
While playing an SVCD... open to the public.
• To playback a bonus group, you have to enter the specific
SUBTITLE “key number” (a kind of password) for the bonus group.
The way of getting the key number depends on the disc.
1 Select the bonus group.

• The bonus group is usually recorded as the last group
(for example, if a disc contains 4 groups including a
bonus group, “group 4” is the bonus group).
• For how to select the group, see “To select a title/group”
on page 10.
Continued on the next page
17
2 Enter the key number. Slow-motion playback
• This does not function for MPEG-1/MPEG-2/ASF/DivX
1 2 3
ENTER/SET discs.
4 5 6 1 While playing...
Still picture playback starts.
7 8 9
3 Follow the interactive instructions shown on the 2 Select slow motion speed.
screen. Forward slow motion starts.
– SLOW +
To cancel the key number entry, press 7. 1/32 1/16 1/8 1/4 1/2
Reverse slow motion* starts.

Making Dialogues Clear—Clear Voice Remote
ONLY
1/32 1/16 1/8 1/4 1/2
When you playback a disc or USB mass storage class device, * Only available for DVD Video.
you can make the singer’s voices or dialogues of the movie
clear—Clear Voice. When Clear Voice is in use, the To resume normal playback, press DVD/CD 3.
C.VOICE indicator lights on the display.
• This function works for center-channel encoded multi-
channel discs and 2-channel discs with 3D Phonic
To replay the previous scenes
activated. (One-Touch Replay)
• This function is only used while playing DVD Video/
C.VOICE C.VOICE DVD-VR.
While playing back...
5
Off The playback position moves
back about 10 seconds before the
current position (only within the
(while holding...) same title).
Special Effect Playback Remote

ONLY INFO
Zoom
Pause playback
1 While playing back...
To pause: To resume normal
playback: ZOOM ZOOM 1 ZOOM 2 ZOOM 3 ZOOM 4
While playing... 7
DVD/CD ZOOM OFF ZOOM 6 ZOOM 5
(while holding...)
2 Move the zoomed-in position.

Frame-by-frame playback TV CH
1 While playing...
Still picture playback starts.
TV CH
2 Advance the still picture frame by frame.

To cancel Zoom, press ZOOM (while holding SHIFT)
repeatedly until “ZOOM OFF” appears on the TV.
To resume normal playback, press DVD/CD 3.
18
Advanced Playback Operations
Remote control Programming the Playing Order
Remote
—Program Play ONLY INFO
You can arrange the playing order of the chapters or tracks

(up to 99) before you start playback.
Number • Program play cannot be used for DVD-VR/JPEG/
buttons MPEG-1/MPEG-2/ASF/DivX and files in a USB mass
ZOOM storage class device.
CANCEL • Resume does not work for Program Play.
TOP MENU/PG MENU/PL
1 Before starting playback, activate Program Play.
, , , ,
USB
MEMORY ENTER/SET FM/PLAY
MODE PROGRAM RANDOM
DVD/CD 3 ON SCREEN
7 Canceled
8
1 4,x
FM/PLAY S.TURBO AHB PRO USB MIC V.MASK C.VOICE PG PL ST MONO
MODE REPEAT A-B PRGR. B.S.P. BONUS PRGM RND 1 TA NEWS INFO 12 3
REC
SLEEP
REPEAT A.STBY
SHIFT REC
On the display
PROGRAM
No Group/Title Track/Chapter
1
2
3
4
5
6
7
8
Main unit 9
10
USE NUMERIC KEYS TO PROGRAM TRACKS.

USE CANCEL TO DELETE THE PROGRAM.
On the TV
2 Select chapters or tracks you want for Program Play.

DVD/CD #/8 • For DVD Video/DVD Audio/MP3/WMA/WAV:
1 Select a title or group number.
USB 2 Select a chapter or track number.
MEMORY
3 Repeat the above steps 1 and 2.
• For SVCD/VCD/CD:
4, 7, x 0 1 Select tracks.
To enter the numbers directly:
Examples:
1 2 3 To enter number 5, press 5.
To enter number 10, press 10.
4 5 6 To enter number 15, press 10,
1, then 5.
7 8 9
To enter number 30, press 10,
10
3, then 10.
10 0
19
3 Start playback. Remote
Playback starts in the order you

Playing at Random—Random Play ONLY
DVD/CD have programmed. You can play all chapters or tracks at random.
• Random Play cannot be used for DVD-VR/JPEG/
MPEG-1/MPEG-2/ASF/DivX, some DVDs and files in the
USB mass storage class device.
To skip a step: To pause: To stop: 1 Before starting playback, activate Random Play.
FM/PLAY
GROUP/TITLE SKIP MODE PROGRAM RANDOM
Canceled
To release, press
DVD/CD 3.
To check the programmed contents REC
SLEEP
A.STBY
Before or after playback... REC
TV CH
In the reverse order. 2 Start playback.

Playback starts in random order.
TV CH DVD/CD Random Play ends when the
In the programmed order. entire disc has been played.
• You can also use 4 or x to check the programmed
contents.
To modify the program To skip a chapter/ To pause: To stop:
Before or after playback... track:
To erase the last track/file:
CANCEL
To release, press
0 DVD/CD 3.
To exit from Random Play

(while holding...) Before or after playback...
To erase the entire program: To add another track/ FM/PLAY
MODE PROGRAM RANDOM
file to the program:
Repeat step 2. Canceled
2 sec.
CANCEL
0
(while holding...)
To exit from Program Play

Before or after playback...
FM/PLAY
MODE PROGRAM RANDOM
Canceled
20
Remote * During Program Play and Random Play, “REP STEP”
Playing Repeatedly ONLY INFO
appears instead of these indications, and repeat modes
• You can also select the repeat mode using the on-screen bar change as follows for all the discs.
(see pages 23 and 24). REP STEP REP ALL
• For MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/
DivX, see page 27. REP OFF
(Canceled)
Repeat Play
You can repeat playback. A-B Repeat
• For DVD Video: You can repeat playback of a desired portion by specifying
While playing... the beginning (point A) and the ending (point B).
• A-B Repeat cannot be used for MP3/WMA/WAV/MPEG-1/
REPEAT A-B MPEG-2/ASF/DivX, some DVDs and files in the USB mass
REPEAT
REP CHAP* REP TTL storage class device.
REP OFF
(Canceled) 1 While playing (without PBC for SVCD/VCD), select
• For DVD Audio: the start point (A).
While playing or before playback... starts flashing on the
REPEAT A-B REPEAT A-B display.
REP TRK *
REPEAT
REPEAT
REP GRP • A- appears on the
TV if the TV is turned on.
REP OFF
(Canceled)
• For CD/SVCD/VCD: (while holding...)

While playing (without PBC for SVCD/VCD) or before
playback... 2 Select the end point (B).
REPEAT A-B
stops flashing.
REPEAT
REP TRK* REP ALL
REPEAT A-B • A-B appears on the
REPEAT
REP OFF TV.
(Canceled)
• You can search for the
• For DVD-VR: end point using the y
While playing an original program... button.
(while holding...)
REPEAT A-B
REPEAT
REP CHAP REP PG
To cancel A-B Repeat, press REPEAT A-B again while
REP OFF REP ALL holding SHIFT.
(Canceled) • A-B Repeat will also be canceled when you stop play or
While playing a Program List... skip the chapter or track.
REPEAT A-B Main Unit
REPEAT
REP CHAP REP PL Prohibiting Disc Ejection—Child Lock ONLY
REP OFF You can lock the disc tray so that no one can eject the loaded
(Canceled)
disc.
• This is possible only while the System is on standby.
REP CHAP* Repeats the current chapter.
While the disc tray is closed...
REP TTL Repeats the current title.
REP TRK* Repeats the current track. QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
REP GRP Repeats the current group. PRGR. B.S.P. BONUS PRGM RND 1 TA NEWS INFO 12 3
REC
SLEEP
A.STBY
REP PG Repeats the current program. REC
REP ALL Repeats the disc or program. (while holding...)

REP PL Repeats the current Program List. To cancel the prohibition, repeat the same procedure.
“UNLOCKED” appears on the display.
21
Remote
On-screen Bar Operations ONLY INFO On-screen Bar Information
You can check the disc information and use some functions 1 Disc type
through the on-screen bar. 2 Playback information
On-screen bars Indication Meanings
Dolby D, LPCM Audio format
DVD Video
3/2.1ch, 2/0.0 ch Channel number
1 2 3 TITLE 2 Current title
Dolby D
DVD-VIDEO 3/2.1ch 14 2CHAP
TITLE
TITLE TIME 1:25:58
CHAP233 TOTAL 0:00:58 CHAP 3 Current chapter
TIME
TIME OFF
OFF CHAP. 1/3
1/3 1/1/3
3 1/3
1/1 GROUP 1 Current group
TRACK 14 Current track
4 Current title
DVD Audio
Current play list
1 2 3
TOTAL 1:25:58 Time indications
DVD-AUDIO LPCM GROUP 14 TRACK 23 TIME 0:00:58
2/0.0ch 3 Operation modes
TIME OFF TRACK 1/ 3 PAGE 1/ 3
Indication Meanings
4 Playback
DVD-VR / Forward/Reverse search
/ Forward/Reverse slow-motion
Pause
Stop
4 Function icons (on the pull-down menu)
SVCD Indication Meanings
TIME Select to change the time
1 2 3 indication.
SVCD TITLE 14 CHAP
TRACK TIME 1:25:58
233 TOTAL 0:00:58 OFF Select to repeat playback.
TIME
TIME OFF
OFF 1/3
ST1 -/1/3
4 1/3 1/3 Select for time search.
CHAP. Select for chapter search.
4 TRACK Select for track search.
VCD
1/3 Select to change the audio
1 2 3 language or channel (see also
page 16).
VCD TITLE 14 CHAP
TRACK TIME 1:25:58
233 TOTAL 0:00:58
1/3 Select to change subtitle
TIME
TIME OFF
OFF 1/3
ST 1/3 1/3
language (see also page 17).
4 1/3 Select to change the view angle
CD (see also page 17).
PAGE 1 / 5 Select to change the page (see
1 2 3
also page 17).
CD TITLE 14 CHAP
TRACK TIME 1:25:58
233 TOTAL 0:00:58
TIME
TIME OFF
OFF 1/3 1/3 1/3
4
MPEG-1/MPEG-2/ASF/DivX
1 2 3
FILE TIME 1:25:58
CHAP 23 TOTAL 00:00:58
USB for MPEG-1/MPEG-2/ASF/DivX

1 2 3
USB TIME 1:25:58
CHAP 23 TOTAL 00:00:58
22
To operate using the On-screen Bar For detailed operations of the following functions, see
Ex.: Selecting a subtitle (French) for DVD Video also “To operate using the On-screen Bar” on the left.
While a disc is selected as the source...
1 Display the entire on-screen bar. To change the time information

You can change the time information in the on-screen bar
ON SCREEN
Dolby D
and the display window on the main unit.
DVD-VIDEO 3/2.1ch TITLE 2 CHAP 3 TIME 0:00:58
Dolby D
* 1 While playing, display the on-screen bar with the
DVD-VIDEO 3/2.1ch
TIME
TIME OFF
OFF CHAP.
TITLE
TITLE
1/3
1/3 1/3
1/3
TIME 1:25:58
CHAP233 TOTAL
14 2CHAP 0:00:58
1/3
1/1
pull-down menu.
Dolby D TIME 1:25:58
CHAP233 TOTAL
DVD-VIDEO 3/2.1ch 14 2CHAP
TITLE
TITLE 0:00:58
disappears TIME
TIME OFF
OFF CHAP. 1/3
1/3 1/3
1/3 1/3
1/1
* This does not appear for MP3/WMA/WAV/JPEG/MPEG- 2 Make sure TIME is selected (highlighted).
1/MPEG-2/ASF/DivX discs and files in a USB mass
storage class device.
3 Change the time indication.
ENTER/SET
TIME 0:00:58 REM 0:11:23
2 Select (highlight) the item you want.
T. REM 0:35:24 TOTAL 1:01:58
TIME Elapsed playing time of the current

Dolby D
14 2CHAP
TITLE
TITLE TIME 1:25:58
CHAP233 TOTAL 0:00:58
chapter/track (except for DVD-VR).
DVD-VIDEO 3/2.1ch
TIME
TIME OFF
OFF CHAP. 1/3
1/3 1/3
1/3 1/3
1/1 REM Remaining time of the current chapter/
track (except for DVD-VR).
3 Display the pop-up window. TOTAL Elapsed disc time.
ENTER/SET
TITLE 2CHAP TOTAL 1:25:58
CHAP233 TOTAL 1:01:58 T. REM Remaining disc time.
1/3
1/3 1/3
1/3 1/3
1/1
To remove the on-screen bar
ENGLISH
ON SCREEN
4 Select the desired option in the pop-up window.

TV CH
TITLE
TITLE TOTAL 1:25:58
CHAP233 TOTAL
14 2CHAP 1:01:58
1/3
1/3 1/3
2/3 1/3
1/1 Repeat Play
TV CH FRENCH • See also page 21.
1 While playing a disc (without PBC for SVCD/VCD),

5 Finish the setting. display the entire on-screen bar.
Pop-up window disappears. • Repeat Play can be selected before starting playback,
ENTER/SET
except for DVD Video/DVD-VR.
2 Select OFF .
3 Display the pop-up window.
Dolby D TOTAL 1:25:58
CHAP233 TOTAL
DVD-VIDEO 3/2.1ch TITLE 14 2CHAP
TITLE 1:01:58
To remove the on-screen bar TIME
TIME OFF
OFF CHAP. 1/3
1/3 1/3
1/3 1/3
1/1
ON SCREEN OFF
23
4 Select the repeat mode you want. Time Search
A-B Repeats a desired portion (see below). You can move to a particular point by specifying the elapsed
playing time from the beginning.
TITLE*1 Repeats the current title.
GROUP Repeats the current group. 1 While playing (without PBC for SVCD/VCD), display
ALL Repeats the disc (except for DVD) or the entire on-screen bar.
program. • Time Search can be used before starting playback,
except for DVD Video/DVD-VR.
CHAPTER*2 Repeats the current chapter.
2
2 Select .
TRACK* Repeats the current track.
3 Display the pop-up window.
OFF Cancels Repeat Play.
Dolby D
TITLE
TITLE TIME 1:25:58
CHAP233 TOTAL
14 2CHAP 0:00:58
*1 While playing a DVD-VR disc, “PG” appears, and DVD-VIDEO 3/2.1ch
TIME
TIME OFF
OFF CHAP. 1/3
1/3 1/3
1/3 1/3
1/1
while playing a Play list, “PL” appears.
TIME _ : _ _ : _ _
*2 During Program Play and Random Play, “STEP”
appears. 4 Enter the time.
5 Finish the setting. You can specify the time in hours/minutes/seconds.
ENTER/SET
Examples:
1 2 3 To move to a point of 1
(hours): 02 (minutes): 00
4 5 6
(seconds), press 1, 0, 2, 0, then
A-B Repeat 8 9
0.
7
• See also page 21. To move to a point of 54
0 (minutes): 00 (seconds), press
1 While playing, display the entire on-screen bar. 0, 5, 4, 0, then 0.
2 Select OFF . • It is always required to enter the hour digit (even “0”
3 Display the pop-up window. hour), but it is not required to enter trailing zeros (the
DVD-VIDEO Dolby D
14 2CHAP
TITLE
TITLE TOTAL 1:25:58
CHAP233 TOTAL 1:01:58 last two digits in the examples above).
3/2.1ch
TIME
TIME OFF
OFF CHAP. 1/3
1/3 1/3
1/3 1/3
1/1
• To correct a mis-entry, press cursor < to erase the last
entry.
OFF
5 Finish the setting.
4 Select “A-B.” The System starts playing the disc
ENTER/SET
TV CH
from the selected playing time.
Dolby D
DVD-VIDEO 3/2.1ch T
TIME
TIME OFF
OFF CHAP.
TV CH
A–B
5 Select the start point (A). Chapter/Track Search

You can search for the chapter (DVD Video/DVD-VR) or
ENTER/SET
DVD-VIDEO
Dolby D
TITLE 14 2CHC
TITLE
track (DVD Audio) number to play.
3/2.1ch
TIME
TIME A- CHAP. 1/3
1/3
1 While playing, display the entire on-screen bar.
2 Select CHAP. or TRACK .
6 Select the end point (B). 3 Display the pop-up window.
Dolby D TOTAL 1:25:58
ENTER/SET A-B Repeat starts. The selected DVD-VIDEO 3/2.1ch
TITLE
TITLE CHAP233 TOTAL
14 2CHAP 1:01:58
portion plays repeatedly. TIME

TIME OFF CHAP. 1/3
1/3 1/3
1/3 1/3
1/1
• Before pressing ENTER/SET, you CHAPTER _
can search for the end point using

the y button.
To cancel A-B Repeat, repeat steps 1 to 3, and select “OFF”

in step 4.
24
4 Enter the desired chapter/track number. Control screen for DVD-R/-RW in DVD-VR format
Examples: The control screen is superimposed on the TV screen when
1 2 3 To select chapter/track 5, press you call up Program List (PG) or Play List (PL).
5. To select playback type
4 5 6 To select chapter/track 10, To select the Program To select the Play List:
press 1, then 0. List:
7 8 9 To select chapter/track 15,
TOP MENU/PG MENU/PL
press 1, then 5.
0
To select chapter/track 30,
press 3, then 0.
• To correct a mis-entry, press the number buttons until To remove the list, press the same button again.
the desired number shown in the pop-up window.
5 Finish the setting. Ex.: When Program List is selected.
ENTER/SET The System starts playing the

ORIGINAL PROGRAM
searched chapter or track.
No Date Ch Time Title
1 03/12/07 L 12:15 La fleur
2 09/12/07 L 23:05 The last struggle
3 18/12/07 L 08:17 free flyer
4 20/12/07 L 07:47 BOOM!
5 25/12/07 L 19:38 Mr. Lawrence
Browsable Still Pictures 6 28/12/07 L 14:20 Satisfy U
For DVD Audio only: While playing back a track linked to

browsable still pictures (B.S.P.), you can select the still
picture (turn the page) to be shown on the TV. 1 2 3 4 5 6
• If a track is linked to browsable still pictures (B.S.P.), they
are usually shown automatically during playback. Ex.: When Play List is selected.
1 While playing a DVD Audio, display the entire PLAY LIST

on-screen bar. No Date Chap Length Title
1 03/12/07 002 0:23:24 Nebula G.
2 Select PAGE 1 / 5 . 2 15/12/07 004 1:04:39 CDJ
3 24/12/07 013 0:41:26 Secret Garden
3 Display the pop-up window. 4 27/12/07 017 0:09:08 S. Walker
DVD-AUDIO LPCM
2/0.0ch
GROUP 14 TRACK 23 TIME 0:00:58
TIME OFF TRACK 1/3 PAGE 1/5
1
1 2 7 8 6
4 Select a still picture you want.
TV CH 1 Listed number
2 Recording date
P 14 TRACK 23 TIME 0:00:58
3 Recording channels
1/3 PAGE 3/5
4 Recording time
TV CH
3 5 Title
6 Highlight bar (current selection)
5 Finish the setting. 7 Chapters included
8 Playback time
ENTER/SET
To select an item in the list and start playback

TV CH
ENTER/SET
TV CH
25
Audio/Video File Operations
Remote control Ex.: While playing a MP3 disc.
6
7
8
RANDOM REPEAT STEP TIME : 00:00:14 9
1
ZOOM Group : 2 / 3 Track : 6 / 14 (Total 41) 0
Spring Cloudy.mp3
2 Summer Fair.mp3
Fall Fog.mp3
, , , ENTER/SET Winter Hail.mp3
3 Indian summer.mp3
USB MEMORY 3
Track Information Rain.mp3 -
Title Shower.mp3
DVD/CD 3 Rain Snow.mp3 =
7 Artist Thunder.mp3
8 4 Typhoon.mp3
GROUP/TITLE Album Wind.mp3
Winter sky.mp3
REPEAT A-B GROUP/TITLE
SKIP 5
REPEAT 4,x
SHIFT 1 Current group number/total group number
2 Current group
3 Group list
4 Track information (ID3 Tag Version 1.0: only for
MP3/WMA/WAV)
5 Current track
6 Random/Program Play setting (except for USB)
Operations on the Control Screen 7 Repeat Play setting
Remote
ONLY INFO 8 Elapsed playing time of the current track
(except for JPEG)
You can search for and play the desired items through the 9 Operation mode icon
control screen for MP3/WMA/WAV/JPEG/MPEG-1/ 0 Current track number/total number of tracks in the
MPEG-2/ASF/DivX files. current group (total number of tracks on the loaded
disc)
Control screen for MP3/WMA/WAV/JPEG/ - Highlight bar
MPEG-1/MPEG-2/ASF/DivX files = Track list
The control screen automatically appears on the TV screen
• If files of different types (MP3, WMA, WAV, JPEG,
when you load a disc or connect and select a USB mass
MPEG-1, MPEG-2, ASF and DivX) are recorded on a
storage class device in which MP3, WMA, WAV, JPEG,
disc or device, select the file type to play (see
MPEG-1, MPEG-2, ASF, or DivX is recorded.
page 35).
To move the highlight bar between group list and track
list
Moves the bar to the track
list.
Moves the bar to the group

list.
To select an item in the list

TV CH Move the highlight bar to the
desired item.
• If you move the highlight bar
TV CH
while playing back an MP3/
WMA/WAV file or DVD-VR
(PG/PL) disc, the selected track
starts playback automatically.
26
To start playback To repeat MP3/WMA/WAV playback
For JPEG: While playing or before playback...
ENTER/SET The selected track (still picture) REPEAT A-B
is displayed until you change it.
REPEAT
REP TRK* REP GRP
REP OFF REP ALL
(Canceled)
DVD/CD USB Press one of the buttons To repeat slide-show for JPEG
USB depending on the current source. While playing or before playback...
DVD/CD MEMORY
Slide-show playback starts. REPEAT A-B
Each track (still picture) is shown REPEAT
REP GRP REP ALL
on the screen for about 3
seconds, then changes one after REP OFF
(Canceled)
another.
For the other files: To repeat MPEG-1/MPEG-2/ASF/ DivX playback
ENTER/SET Playback starts with the selected While playing or before playback...
track. REPEAT A-B
• Pressing DVD/CD 3 or REPEAT
REP TRK* REP GRP
USB MEMORY 3 also starts
playback. REP OFF REP ALL
(Canceled)
• Once you start viewing a JPEG/MPEG-1/MPEG-2/
ASF/DivX track, the control screen disappears. REP TRK* Repeats the current track.
• To cancel slide-show and display the current still picture, REP GRP Repeats the current group.
press 8.
REP ALL Repeats the disc.
To select a group:
* During Program Play and Random Play, “REP STEP”
appears instead of this indication.
GROUP/TITLE SKIP
To zoom in the JPEG files
• You cannot zoom in the still picture during slide-show.
1 While playing back a still picture...
• During slide-show, press 8 to display the still picture,
(while holding...) then...
To skip a track: To stop playback:

ZOOM
ZOOM 1 ZOOM 2
GROUP/TITLE SKIP
7
ZOOM OFF
(while holding...)
• You can select a group directly by pressing a number
button after pressing GROUP/TITLE (except for DVD-VR 2 Move the zoomed-in position.
disc). TV CH
TV CH
To cancel Zoom, press ZOOM (while holding SHIFT)

repeatedly until “ZOOM OFF” appears on the TV.
27
Advanced Tape Operations
IMPORTANT
Remote control
It may be unlawful to record or playback copyrighted
material without the consent of the copyright owner.
Recording on a Tape INFO
You can use type I tapes for recording.

• To play a tape, see page 9.
1 Insert a recordable cassette.

USB MEMORY 3 Push Insert Close
TAPE
DVD/CD 3 FM/AM/AUX
7
With the tape side facing outside
2 Select and start playing the source—“FM,” “AM,”

“DVD/CD,” “USB MEM,” or “AUX.”
• When recording from a disc or USB source, you can
also use “Synchronized Recording” (see page 29).
3 Start recording.
REC
Main unit
On the main unit

PUSH OPEN 0 To stop recording:
FM/AM/AUX
DVD/CD #/8
USB TAPE
MEMORY #/8 REC
28
Synchronized Recording INFO To record only your favorite track
You can specify tracks to be recorded on the tape while
You can start and stop both playback and tape recording at listening from a disc (except for DVD Video/DVD-VR) or
the same time. USB mass storage class device.
To record the entire tracks 1 Start playing a disc/file.

USB
1 Load a disc or connect a USB mass storage class DVD/CD MEMORY
device and insert a recordable cassette.
• Press DVD/CD 3 or USB MEMORY 3 to select the
current playing source, then 7.
2 While a track you want to record on the tape is
2 Start recording. playing...
The System automatically Playback returns to the
REC REC
creates 4-second blanks between beginning of that track and the
the tunes recorded on the tapes. track is recorded on the tape.
After recording the track,
On the main unit On the main unit playback and recording
automatically stop.
• When either playback* or recording ends, both playback
and recording stop at the same time. 3 Repeat steps 1 and 2 to record other tracks you want.
* For DVD Video: When a title is finished playing. • You can change the disc if necessary.
• When the tape reaches its end, both playback and recording
also stop at the same time. To protect your recording
Cassettes have two small tabs on the back to protect
To record a “Live” disc from unexpected erasure or re-recording.
It will not be desirable to put 4-second blank portions To protect your recording, remove these tabs.
between the tunes recorded on the tape.
To record the entire tracks without any interruption
recorded, pause playback (press DVD/CD 3 or USB
MEMORY 3, then 8) before pressing REC.
To record Program Play To re-record on a protected tape, cover the holes with
1 Select Program Play (and make a program), but do not adhesive tape.
start playback.
2 Press REC to start recording.
• When disc play stops, recording stops automatically.
29
Enjoying Karaoke
IMPORTANT
Remote control Always set MIC VOLUME to MIN when connecting or
disconnecting the microphone.
DO NOT keep the microphone connected

while they are not in use.
KEY , KEY
Singing Along (Karaoke) INFO
To sing along using the Karaoke discs

ECHO You can enjoy Karaoke using the Karaoke disc (except
RESERVE Karaoke CD).
KARAOKE • By pressing REC, you can record your singing-along (for
USB MEMORY 3
DVD/CD 3 FM/AM SVCD/VCD without PBC).
7 /AUX
TAPE
1 Turn MIC VOLUME to MIN.
VOLUME
AUDIO/MPX
SHIFT MIN MAX
2 Connect the microphone (not supplied) to the MIC

jack.
MIC VOLUME
MIN MAX
Main unit 3 Insert and start playing a Karaoke disc.

4 Select an audio track.
AUDIO/MPX
MIC jack
MIC VOLUME
• For details, see “Selecting the Audio Track” on page 16.
5 Sing into the microphone.
6 Adjust the MIC VOLUME and VOLUME.
VOLUME VOLUME
DVD/CD #/8 FM/AM/AUX

USB TAPE
MEMORY #/8 REC
MIN MAX
VOLUME
Karaoke function is not available in the Australian model.
30
To adjust the Key (disc/file playback only) 4 Activate Vocal Masking.
1 Activate Key Control. ON SCREEN
KARAOKE
KEYCON V-CANCEL
ON SCREEN OFF
KARAOKE
KEYCON V-CANCEL (Canceled)
OFF (while holding...)

(Canceled)
(while holding...) 6 Adjust the MIC VOLUME and VOLUME.
2 Adjust the Key VOLUME VOLUME
KEY KEY
To raise the
key. MIN MAX
To lower the • You can apply echo to your voice.

key.
(while holding...)
To deactivate Vocal Masking, select “OFF” in step 4.
• Key Control cannot be activated for DVD Audio/
DVD-VR/MPEG-1/MPEG-2/ASF/DivX.
To deactivate Key Control, press KARAOKE (while Microphone Mixing
holding SHIFT) to select “OFF.” You can enjoy microphone mixing while playing any source.
To apply echo to your voice • By pressing REC, you can record your singing-along
(except when the playing source is “TAPE”).
MENU/PL
ECHO
ECHO ON 1 Turn MIC VOLUME to MIN.
VOLUME
ECHO OFF
(Canceled)
(while holding...) MIN MAX
To sing along using the stereo discs/audio files

—Vocal Masking 2 Connect the microphone (not supplied) to the MIC
You can enjoy Karaoke while playing a stereo disc or an jack.
audio file.
Vocal Masking reduces the lead vocal of any disc except 3 Start playing the source—“FM,” “AM,” “DVD/CD,”
DVD Audio and DVD-VR. “USB MEM,” “TAPE,” or “AUX.”
1 Turn MIC VOLUME to MIN.
VOLUME
5 Adjust the MIC VOLUME and VOLUME.
VOLUME VOLUME
MIN MAX
2 Connect the microphone (not supplied) to the MIC

jack. MIN MAX
3 Insert and start playing a stereo disc or start playing

an audio file. • You can apply echo to your voice. While playing a disc,
DVD/CD USB
you can also adjust Key Control and apply echo.
USB
• When selecting “TAPE” as the source, microphone
DVD/CD MEMORY mixing is available only during tape playback.
To use the microphone only, select “AUX” in step 3, but do

not start playback.
31
4 Start playback.
Reserving Karaoke Songs Remote
ONLY
DVD/CD
—Karaoke Program Play
You can determine the playback order of the titles or tracks Playback starts in the order
on the disc player. You can program up to 12 steps. you have programmed.
1 Change the source to “DVD/CD.” To check the programmed contents

During Karaoke Program Play...
DVD/CD
The Karaoke reserve screen appears.
2 Activate Karaoke Program Play. To modify the program

While the Karaoke reserve screen is shown on the TV...
SET UP
To remove the unwanted track:
RESERVE TV CH
CANCEL
0
(while holding...) TV CH
No Gr/Tt Tr/Chap
1 (while holding...)
2
3
4
To add another track to the program:
5 Repeat step 3.
On the TV screen To erase the entire program:
• PRGM indicator flashes during this mode.
2 sec.
3 Select songs you want for Karaoke Program Play.
Press the number buttons to select a song in the following CANCEL
order. 0
1 Select a title/group.
2 Select a chapter/track.
Examples:
1 2 3 To select preset number 5, To exit from Karaoke Program Play
press 5. Before or after playback...
press 10. SET UP
7 8 9
To select preset number 15, RESERVE
10 0 10
To select preset number 30,
(while holding...)
During playback...
SET UP
RESERVE
(while holding...)
32
Timer Operations
1 Select one of the timer setting modes you want to set—
Remote control DAILY 1 ON time, DAILY 2 ON time, DAILY 3 ON
time, or REC TMR(Recording Timer) ON time.
CLOCK/TIMER
6
AUDIO
CLOCK/TIMER
(while holding...)
CANCEL DAILY Timer 1 DAILY Timer 2 DAILY Timer 3
ENTER/SET DAILY 1 ON (Time) DAILY 2 ON (Time) DAILY 3 ON (Time)
,
Canceled Clock setting ON (Time) REC TMR
(see page 15) Recording Timer

REC
SLEEP
A.STBY
REC
Ex. When Daily Timer 1 setting mode is selected

SHIFT
• When the clock has not been set, pressing CLOCK/
TIMER (while holding SHIFT) makes the System enter
the clock setting mode.
2 Make the timer setting as you want.
Repeat the procedure for the following settings until
finished—
Remote
Setting the Timer ONLY INFO
ENTER/SET
Using Daily Timer, you can wake up with your favorite
music. On the other hand, with Recording Timer, you can
make a tape of a radio broadcast automatically.
You can store three Daily Timer settings and one Recording
Timer setting; however, you can activate only one of the
1 Set the hour then the minute for on-time.
timers at the same time.
• To exit from the timer setting, press CLOCK/TIMER 2 Set the hour then the minute for off-time.
(while holding SHIFT) as required. 3 Select the playback source—“TUNER FM,”
• To correct a mis-entry during process, press CANCEL “TUNER AM,” “TAPE,” “DISC,”
(while holding SHIFT). You can go back to the previous “USB MEM,” or “AUX.”
step. QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
REC
SLEEP
Daily Timer initial settings when shipped from the A.STBY
factory REC
• DAILY 1: ON Time (6:00)/OFF Time (8:00)/

Source (TUNER FM 1)/Volume level (– –) 4 For “TUNER FM” and “TUNER AM”: Select a
• DAILY 2: ON Time (7:00)/OFF Time (9:00)/
preset channel.
Source (TUNER FM 1)/Volume level (– –)
• DAILY 3: ON Time (10:00)/OFF Time (12:00)/ For “DISC”: Select the title/group number, then
Source (TUNER FM 1)/Volume level (– –) the chapter/track number.
For “USB MEM”: Select the group number, then
the track/file number.
33
5 Select the volume level. To turn on or off the Timer
• You can adjust the volume level (“1” to “40” Since Daily Timer is activated at the same time everyday,
and “VOL – –”). you may need to cancel it on some particular days.
If you select “VOL – –,” the volume is set to the last To cancel the Timer
level when the unit has been turned off.
Once settings are completed, the Timer setting
1 Select the Timer (DAILY 1, DAILY 2, or DAILY 3)
you want to cancel.
information appears in sequence.
• This function is not available for VCD with PBC
activated. CLOCK/TIMER
For Recording Timer: 6
1 Set the hour then the minute for on-time.
2 Set the hour then the minute for off-time.
3 Select the playback source—“TUNER FM,” (while holding...)
“TUNER AM,” or “AUX.” DAILY Timer 1 DAILY Timer 2 DAILY Timer 3
4 For “TUNER FM” and “TUNER AM”: Select a DAILY 1 ON (Time) DAILY 2 ON (Time) DAILY 3 ON (Time)
preset channel.
Once settings are completed, the Timer setting Canceled Clock setting ON (Time) REC TMR
(see page 15) Recording Timer
information appears in sequence. The volume is set to the
last level when the unit has been turned off. QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
3 Turn off the unit (on standby).
REC
SLEEP
A.STBY
Ex. To cancel Daily
Timer 1
REC
2 Turn off the selected Timer.
CANCEL
0
How Daily Timer works
Once the Daily Timer has been set, the timer indicator
( ) and timer number indicator (1/2/3) are lit on the (while holding...)
display. Daily Timer is activated at the same time
everyday until the timer is turned off manually (see the To turn on the Timer
next column) or another timer is activated.
When the on-time comes 1 Select the Timer (DAILY 1, DAILY 2, or DAILY 3)
The System turns on, tunes in to the specified station or you want to activate.
starts playing the loaded disc with the specified chapter or
track, and sets the volume level gradually to the preset CLOCK/TIMER
level after about 30 seconds.
6
• While Daily Timer is working, the timer indicator ( )
flashes on the display.
When the off-time comes
The System stops playback, and turns off (on standby) (while holding...)
automatically. DAILY Timer 1 DAILY Timer 2 DAILY Timer 3
• The timer setting remains in memory until you change DAILY 1 ON (Time) DAILY 2 ON (Time) DAILY 3 ON (Time)
it.
Canceled Clock setting ON (Time) REC TMR
How Recording Timer works (see page 15) Recording Timer
When Recording Timer has been set, Timer ( )
indicator and the REC indicator are lit on the display. 2 Activate the selected Timer.
Recording Timer works only once. QP Link S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM
When the on-time comes ENTER/SET PRGR. B.S.P. BONUS PRGM RND 1 TA NEWS INFO 12 3
REC
SLEEP
The System turns on, tunes in to the specified station or A.STBY
changes the source to “AUX”, and starts recording. REC
When the off-time comes Ex. When Daily Timer 1 (DAILY 1) is

The System stops recording, and turns off (on standby). activated
• The timer setting remains in memory until you change
it.
3 Wait until the indication disappears.
34
Setup Menu Operations INFO
Remote
Remote Control
Initial settings ONLY
The Setup Menu cannot be activated during playback.
1 Press SET UP.

LANGUAGE
MENU LANGUAGE ENGLISH
AUDIO LANGUAGE ENGLISH
SUBTITLE ENGLISH
ON SCREEN LANGUAGE ENGLISH
, , ,
ENTER/SET
SET UP
2 Press (or )to select the menu.
3 Press (or ) to move to select the item.
4 Press ENTER/SET.
5 Press (or ) to select the options, then press
ENTER/SET.
• For settings of the LANGUAGE menu, see also
“Language Code List” on page 42.
To remove a preference display
Press SET UP.
LANGUAGE menu
Item Contents
MENU LANGUAGE You can select the initial menu language of the DVD Video.
AUDIO LANGUAGE You can select the initial audio language of the DVD Video.
SUBTITLE You can select the initial subtitle language of the DVD Video.
ON SCREEN LANGUAGE You can select “ENGLISH,” “CHINESE,” or “SPANISH” as the on-screen language.
PICTURE menu
Item Contents
MONITOR TYPE You can select the monitor type to match your TV when you playback DVD Video discs recorded for
16:9 4:3 LB wide-screen televisions.
16:9 NORMAL/16:9 MULTI NORMAL (Wide television screen): Select this when the aspect ratio
of your wide TV is fixed to 16:9.
16:9 AUTO/16:9 MULTI AUTO (Wide television screen): Select this when your TV is an ordinary
wide TV.
4:3 PS 4:3 LB/4:3 MULTI LB (Letter Box conversion): For a conventional (4:3) TV. Displays a
wide-screen picture to fit the width of the TV screen keeping the aspect ratio.
4:3 PS/4:3 MULTI PS (Pan Scan conversion): For a conventional (4:3) TV. The picture is zoomed
in to fill the screen vertically and the left and right sides of the picture are cut off.
• For multi-color system TVs, select the [MULTI] option.
PICTURE SOURCE You can obtain optimal picture quality by selecting the source type of the disc contents.
AUTO: Normally, select this option. The System recognizes the picture type (film or video source) of
the current disc according to the disc information.
FILM: For a film source disc.
VIDEO: For a video source disc.
SCREEN SAVER You can set the screen saver function to ON or OFF. If no operation is done for about 5 minutes, the
display dims.
FILE TYPE You can select the file type to play.
AUDIO: To play MP3/WMA/WAV files.
STILL PICTURE: To play JPEG files.
VIDEO: To play MPEG-1/MPEG-2/ASF/DivX files.
35
AUDIO menu
Item Contents
DIGITAL AUDIO OUTPUT Set this item correctly when using the OPTICAL DIGITAL OUT terminal on the rear.
PCM ONLY: When connecting to audio equipment which can decode only linear PCM signals.
DOLBY DIGITAL/PCM: When connecting to a Dolby Digital decoder or an amplifier with a built-
in Dolby Digital decoder.
STREAM/PCM: When connecting to a DTS decoder or an amplifier with a built-in DTS decoder.
DOWN MIX This setting is effective for digital audio output if “DIGITAL AUDIO OUTPUT” is set to “PCM
ONLY.”
DOLBY SURROUND: Select this when connecting to a surround decoder.
STEREO: Select this when connecting to a stereo receiver, MD player, TV, etc.
D. RANGE COMPRESSION Set this item to listen to DVD Video recorded in Dolby Digital format at low or middle volume.
AUTO: You can enjoy powerful playback sound with full dynamic range.
ON: Select this when you want to fully apply the compression effect to make the sound at lower
volume clear (useful at midnight).
OTHERS menu
Item Contents
RESUME You can select Resume.
ON: The System resumes playback from the position where playback has been stopped if the disc is
still in the disc tray.
OFF: Resume is deactivated.
ON SCREEN GUIDE Activate or deactivate the on-screen guide.
DivX REGISTRATION The System has its own Registration Code.
If necessary, you can confirm it.
Once you have played back a disc in which the Registration Code is recorded, the System’s
Registration Code is overwritten for copyright protection.
36
Additional Information
• This System can recognize up to 4 000 tracks in a disc.
Learning More about This System Also, the System can recognize up to 150 tracks per group
Connections (see pages 3 to 5) and up to 99 groups in a disc.
• Make sure the antenna conductors do not touch any other – If there are any unplayable files in a folder, those files are
terminals, connecting cords or the power cord. Also, keep also counted in the total file number.
the antennas away from metallic parts of the System, – Playable files which do not belong to any groups are
connecting cords and the AC power cord. This could cause handled as group 1.
poor reception. • For playback of files in the USB mass storage class
• Use only speakers with the same speaker impedance as device...
indicated by the speaker terminals on the rear of the System. – While the System is reading a disc, changing the source
• The speakers are magnetically shielded to avoid color to USB MEMORY may cause the System to continue
distortions on TVs. However, if not installed properly, it playback the DVD/CD source. In this case, press 7 on
may cause color distortions. So, pay attention to the the main unit to reactivate the USB source.
following when installing the speakers. – When connecting a USB mass storage class device, refer
– When placing the speakers near a TV set, turn off the also to its manual.
TV’s main power switch or unplug it before installing the – Connect one USB mass storage class device to the
speakers. System at a time. Do not use a USB hub.
Then wait at least 30 minutes before turning on the TV’s – You cannot charge any USB device through the USB
main power switch again. MEMORY jack of this System.
– Some TVs may still be affected even though you have – While playing back a file in a USB mass storage class
followed the above instructions. If this happens, move device, do not disconnect the device. It may cause a
the speakers away from the TV. malfunction of both the System and the device.
Daily Operations—Playback (see pages 7 to 11) – JVC bears no responsibility for any loss of data in the
Listening to the Radio: USB mass storage class device while using this System.
• If you store a new station into an occupied preset number, – When connecting with a USB cable, use the cable whose
the previously stored station in that number will be erased. length is less than 1 m.
• When you unplug the AC power cord or if a power failure – This System is compatible with the USB Full-Speed (not
occurs, the preset stations will be erased in a few days. If compatible with the USB 1.1).
this happens, preset the stations again. – You can playback the following types of files in a USB
Playing Back a Disc/File: mass storage class device (maximum data transfer rate:
• When you change the source to DVD/CD or USB 2 Mbps):
MEMORY, it may take a while to activate the source. – Music: MP3, WMA, WAV
– Picture: JPEG
• The following functions cannot be used for the files in the – Movie: MPEG-1, MPEG-2, ASF, DivX (maximum
USB mass storage class device: frame rate of 30 fps for progressive)
– Selecting the View Angle (page 17) – You cannot playback a file larger than 2 Gigabyte.
– Special Effect Playback (page 18) – When playing a file which has a large transfer rate,
– Program Play (page 19) frames or sounds may be dropped during playback.
– A-B Repeat (page 21) – This System cannot recognize a USB mass storage class
– Time Search (page 24)
device whose rating is other than 5 V and does not
• On some DVD, SVCD, or VCD discs, the actual operations
exceed 500 mA.
may be different from what is explained in this manual, due
– This System may not playback some USB mass storage
to the programming and disc structure; such differences are
class devices and does not support DRM (Digital Rights
not a malfunction of this System.
Management).
• If you playback a DVD Video for more than 10 hours, “_”
– This System may not playback some files even though
appears instead of the hour digits.
their formats are listed above.
• Some DVD Audio discs prohibit downmix. When you
– It will take some time to start up a Digital Audio Player
playback such a disc, “LR ONLY” appears on the display
(DAP) larger than 1 Gigabyte.
and the System plays back the left front and right front
• For DVD-VR playback...
signals.
– This System can play only a disc of UDF-Bridge format.
• When playing back a DVD Audio disc recorded in MLP
– For details about DVD-VR format and play list, refer to
(Meridian Lossless Packing; a lossless audio compression
the manual of the recording equipment.
system that can completely recreate the PCM signal), the – You cannot use reverse slow motion, Program Play, or
signals are recognized as the linear PCM signals, however, Random Play.
no indicator lights up on the display.
37
• For MP3/WMA/WAV playback... – Some recorded files may not be able to playback
– MP3/WMA/WAV discs require a longer readout time depending on file characteristics, kind of digital camera/
than regular CDs. (It depends on the complexity of the video camera, or recording conditions.
group/file configuration.) – You cannot use the following functions—One Touch
– Some MP3/WMA/WAV files cannot be played back and Replay, Slow motion, A-B Repeat, Program Play and
will be skipped. This results from their recording Random Play.
processes and conditions. • For DivX playback...
– This System can play only a disc of ISO 9660 Level 1 or – This System can play only a disc of UDF-Bridge format.
Level 2. “Multi-border” is not supported.
– This System can playback MP3/WMA/WAV files with – The System supports all versions of DivXR video
the extension code <.mp3>, <.wma>, or <.wav> (including DivXR 6).
(regardless of the letter case—upper/lower). – The System supports DivX files whose resolution is 720
– It is recommended that you make each MP3/WMA/ x 480 pixels or less (30 fps), and 720 x 576 pixels or less
WAV file at a sampling rate of 44.1 kHz and at a bit rate (25 fps).
of 128 kbps. For WAV files: 44.1 kHz/16 bit. This – Audio stream should conform to Dolby Digital, MPEG1
System cannot playback files made at a bit rate of less Audio Layer-2, or MPEG Audio Layer-3 (MP3).
than 64 kbps. – This System can playback DivX files with the extension
• For JPEG files playback... code <.divx> <.div> <.avi> (regardless of the letter
– It is recommended that you record a file at 640 x 480 case—upper/lower).
resolution. (If a file has been recorded at a resolution of – The System does not support GMC (Global Motion
more than 640 x 480, it will take a long time to be Compression).
shown.) – The file encoded in the interlaced scanning mode may
– This System can play only baseline JPEG files*. not be played back correctly.
Progressive JPEG files* or lossless JPEG files* cannot – You cannot use the following functions—One Touch
be played. Replay, Slow motion, A-B Repeat, Program Play,
* Baseline JPEG format: Used for digital cameras, Random Play and on-screen operations.
web, etc. Playing Back a Portable Audio Device:
Progressive JPEG format: Used for web. • When QP Link fails due to a weak sound signal from the
Lossless JPEG format: An old type and rarely AUX jack, Auto Standby may turn the System off even if
used now. you can hear the sound from the speakers.
– This System can playback JPEG files with the extension In such cases, adjust the volume level of the component
code <.jpg> or <.jpeg> (regardless of the letter case— louder so that the System can detect the sound signal
upper/lower). properly.
– This System may not playback JPEG files properly if • Changing from AUX to another source while QP Link
they are recorded from a device other than a digital works will deactivate QP Link temporarily.
camera. In this case, the following reactivates QP Link:
– During slide-show playback, zoom cannot be operated. – Pressing QP LINK on the remote control twice.
• For MPEG-1/MPEG-2 playback... – Unplug the component from the AUX jack, then plug it
– The stream format should conform to MPEG system/ in again.
program stream. • If you press (Standby/on) to turn the System off or if
– 720 x 576 pixels (25 fps)/720 x 480 pixels (30 fps) is preset Timer turns the System off while QP Link works,
recommended for the highest resolution. the System will deactivate QP Link temporarily.
– This System also supports the resolutions of 352 x 576/ In such cases, the following reactivates QP Link:
480 x 576/352 x 288 pixels (25 fps) and 352 x 480/480 x – When the sound signal from the AUX jack stops or is too
480/352 x 240 pixels (30 fps). weak for about 30 seconds after the System is turned off.
– The file format should be MP@ML (Main Profile at – When you turn on the power again.
Main Level)/SP@ML (Simple profile at Main Level)/ • QP Link may start working when you just plug in the
MP@LL (Main Profile at Low Level). component to the AUX jack or unplug it. This is not a
– Audio streams should conform to Dolby Digital, MPEG1 malfunction.
Audio layer-2 or MPEG2 Audio Layer-2.
• For ASF playback...
– This System can playback ASF files with the extension
code <.asf> (regardless of the letter case—upper/lower).
– This System supports ASF files whose resolution is 352
x 288 pixels or less.
38
Daily Operations—Sound & Other Adjustments or radio broadcasts, wind the leader tape first to ensure that
(see pages 12 to 15) the recording will be made without any music part lost.
• If you start recording with no cassette inserted, “NO REC”
Adjusting the Sound:
appears on the display. If a protected tape has been
• This function also affects the sound through the headphones.
inserted, “NO REC” appears.
Changing the Scanning Mode:
• You cannot open or close the disc tray while recording a
• You cannot change the scanning mode to progressive in the
disc.
following cases:
Synchronized Recording:
– When your TV does not support the progressive video input.
• Synchronized recording does not function on the file
– When you have not connected your TV to the system
format of MPEG-1, MPEG-2, ASF, and DivX.
using a component video cord.
Setting the Clock: Enjoying Karaoke (see pages 30 to 32) (Not
• “0:00” will flash on the display until you set the clock. available in the Australian model)
• The clock may gain or lose 1 to 2 minutes per month. If this
Singing Along (Karaoke):
happens, reset the clock.
• Karaoke mode setting (Key Control and Vocal Masking)
Unique DVD/VCD Operations (see pages 16 to 18) can be used when selecting “DVD/CD” or “USB
Selecting the Audio Track: MEMORY” as the source, except for DVD-VR/DVD
• On some DVD Video discs, you cannot change audio Audio/MPEG-1/MPEG-2/ASF/DivX files.
languages while playing back. Even if the source is “DVD/CD” or “USB MEMORY,”
Karaoke mode setting cannot be used while “NO DISC” or
Special Effect Playback:
“NO DEVICE” appears on the display.
• During slow-motion playback, no sound will be reproduced.
• Karaoke mode setting is automatically canceled when the
• While zoomed in, the picture may look coarse.
source is changed.
Advanced Playback Operations (see pages 19 • When selecting “DVD/CD” or “USB MEMORY” as the
to 25) source, the microphone is not available while playback is
stopped or paused. To use the microphone, activate Key
Programming the Playing Order—Program Play:
Control or Vocal Masking.
• While programming steps...
• Karaoke mode setting is also applied to the optical digital
Your entry will be ignored if you have tried to program an
output signals.
item number that does not exist (for example, selecting
• When Vocal Masking is activated, 3D Phonic will be
track 14 on a disc that only has 12 tracks).
canceled temporarily.
Playing Repeatedly:
• On some music discs, Vocal Masking does not provide the
• A-B Repeat can be used within the same title while playing
correct effect.
a DVD Video, and within the same track for the other discs.
• You can also use the microphone when selecting “FM,”
On-screen Bar Operations: “AM,” or “AUX” as the source. When selecting “TAPE”
• For DVD-R/-RW in the VR format, “PG” or “PL” appears as the source, you can use the microphone only during tape
instead of “TITLE” on the on-screen bar. playback.
Audio/Video File Operations (see pages 26 Timer Operations (see pages 33 and 34)
and 27) Setting the Timer:
Operations on the Control Screen: • If you do not specify the preset station or track number
• If you press ON SCREEN on the remote control during correctly while setting a timer, the currently selected
video file playback, playback information appears on the station or the first track will be played when the timer is
TV screen. activated.
• If you press ON SCREEN on the remote control during • When you unplug the AC power cord or if a power failure
audio file playback, “ ” will appear on the TV screen. occurs, the timer will be canceled. You need to set the
clock first, then the timer again.
Advanced Tape Operations (see pages 28 and 29)
• If you set DVD Video as the source, Daily Timer will not
Recording on a Tape: work correctly.
• The recording level is automatically set correctly. Thus,
Timer Priority:
you can adjust the sound you are actually listening to
• If you set the Sleep Timer after Daily Timer starts playing
without affecting the recording level.
the selected source, Daily Timer is canceled.
• There is leader tape which cannot be recorded onto at the
start and end of cassette tapes. Thus, when recording CDs
39
Setup Menu Operations (see pages 35 and 36) Cleaning the System
General: • Stains should be wiped off with a soft cloth. If the System
• If the upper and lower parts of the menu are cut off, adjust is heavily stained, wipe it with a cloth soaked in water-
the picture size control of the TV. diluted neutral detergent and wrung well, then wipe clean
LANGUAGE menu: with a dry cloth.
• When the language you have selected for MENU • Since the System may deteriorate in quality, become
LANGUAGE, AUDIO LANGUAGE, or SUBTITLE is damaged or get its paint peeled off, be careful about the
not recorded on a disc, the original language is used as the following:
initial language. – DO NOT wipe it with a hard cloth.
PICTURE menu—MONITOR TYPE: – DO NOT wipe it forcefully.
• Even if “4:3 PS/4:3 MULTI PS” is selected, the screen size – DO NOT wipe it with thinner or benzine.
may become 4:3 letter box while playing a disc. This – DO NOT apply any volatile substance such as
depends on how the discs are recorded. insecticides to it.
• When you select “16:9 NORMAL/16:9 MULTI – DO NOT allow any rubber or plastic to remain in contact
NORMAL” or “16:9 AUTO/16:9 MULTI AUTO” for a for a long time.
picture whose aspect ratio is 4:3, the picture slightly
changes due to the process for converting the picture width. To remove the speaker grilles:
OTHERS menu—ON SCREEN GUIDE:
• The setup menu and on-screen bar will be displayed (and
recorded) even though this function is set to “OFF.”
Subtitles and the information for zoom-in always appear on
the display regardless of this setting.
Maintenance
To get the best performance of the System, keep your discs,
tapes and mechanism clean. Speaker
grille
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc. Holes Projection
• Put the disc back in its case after use to prevent warping.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, extreme temperature,
and moisture.
To clean the disc:
Wipe the disc with a soft cloth in a straight line from center
to edge.
Handling cassette tapes

• If the tape is loose in its cassette, take up the slack by inserting
a pencil in one of the reels and rotate it.
– If the tape is loose, it may get stretched, cut, or caught in the
cassette.
• Be careful not to touch the tape surface.
• Avoid the following places to store the tape—in dusty places,
in direct sunlight or heat, in moist areas, on a TV or speaker,
or near a magnet.
To keep the best recording and playback sound quality:
• Use a cotton swab moistened with alcohol to clean the heads,
capstans, and pinch rollers.
• Use a head demagnetizer (available at electronics and audio
shops) to demagnetize the heads (when the System turned off).
40
sYou have changed the “FILE TYPE” setting after the
Troubleshooting System read the disc or the USB mass storage class
General: device. In this case, reload the disc or disconnect the
USB mass storage class device and connect it again.
Adjustments or settings are suddenly canceled before
you finish. “NO AUDIO” appears.
sThere is a time limit. Repeat procedure again. sThis System cannot playback illegally produced DVD
Audio discs.
Operations are disabled.
sThe built-in microprocessor may malfunction due to “LR ONLY” appears.
external electrical interference. Unplug the AC power sSome DVD Audio discs prohibit downmixed output.
cord and then plug it back in. When you playback such a disc, this System plays back
the left front and right front signals only.
Unable to operate the System from the remote control.
sThe path between the remote control and the remote The disc sound is discontinuous.
sensor on the System is blocked. sThe disc is scratched or dirty.
sThe batteries are exhausted. No subtitle appears on the display though you have
No sound is heard. selected the initial subtitle language.
sSpeaker connections are incorrect or loose. sSome DVDs are programmed to always display no
sHeadphones are connected. subtitle initially. If this happens, press SUBTITLE after
starting playback (see page 17).
No picture appears on the screen.
sThe video cord connections are incorrect or loose. Audio language is different from the one you have
selected as the initial audio language.
No picture is displayed on the TV screen, the picture is
sSome DVDs are programmed to always use the original
blurred, or the picture is divided into two parts.
language initially. If this happens, press AUDIO/MPX
sThe System is connected to a TV which does not support
after starting playback (see page 16).
progressive video input.
The disc tray does not open or close.
The left and right edges of the picture are missing on the
sThe AC power cord is not plugged in.
screen.
sChild Lock is in use. “LOCKED” appears in the display
sSelect “4:3 LB” for “MONITOR TYPE” (see page 35).
window (see page 21).
Radio Operations:
Tape Operations:
Hard to hear broadcasts because of noise.
sAntennas connections are incorrect or loose. The cassette holder cannot be opened.
sPower supply from the AC power cord has been cut off
sThe AM loop antenna is too close to the System.
while the tape was running. Turn on the System.
sThe FM antenna is not properly extended and positioned.
Disc/File Playback Operations: QP Link Operations:

The disc does not play. The System automatically turns on even if the Timer
turn the System to standby or if you turn the System to
sYou have inserted a disc whose Region Code is not
standby while playback is going on the portable audio
correct. (“RG ERROR” appears on the display.) device.
sThe disc is placed upside down. Place the disc with the s In this case, deactivate QP Link or stop playback on the
label side up. device connected to the AUX jack.
ID3 Tag on an MP3/WMA/WAV file cannot be shown.
sThere are two types of ID3 Tag—Version 1 and Version 2. Recordings:
This System can only show ID3 Tag Version 1. Impossible to record.
Groups and tracks are not played back as you expect. sSmall tabs on the back of the cassette are removed.
sThe playing order is determined when the groups and Cover the holes with adhesive tape.
tracks were recorded. It depends on the writing
application.
Timer Operations:
MP3, WMA, WAV, JPEG, MPEG-1, MPEG-2, ASF or Daily Timer does not work.
DivX files are not played back. sThe System has been turned on when the on-time comes.
sThe disc or the USB mass storage class device may Timer starts working only when the System is turned off.
include different types of tracks (ex. MP3/WMA/WAV Daily Timer does not start playback.
files and JPEG files). In this case, you can only playback sThe disc loaded is a DVD Video. Change the disc.
the files selected by the “FILE TYPE” setting (see sTitle/group number and chapter/track number are not
page 35). entered while setting the Daily Timer. Do not skip these
steps when you want to play a disc using Daily Timer.
41
Language Code List
AA Afar JW Javanese SM Samoan
AB Abkhazian KA Georgian SN Shona
AF Afrikaans KK Kazakh SO Somali
AM Ameharic KL Greenlandic SQ Albanian
AR Arabic KM Cambodian SR Serbian
AS Assamese KN Kannada SS Siswati
AY Aymara KO Korean (KOR) ST Sesotho
AZ Azerbaijani KS Kashmiri SU Sundanese
BA Bashkir KU Kurdish SV Swedish
BE Byelorussian KY Kirghiz SW Swahili
BG Bulgarian LA Latin TA Tamil
BH Bihari LN Lingala TE Telugu
BI Bislama LO Laothian TG Tajik
BN Bengali, Bangla LT Lithuanian TH Thai
BO Tibetan LV Latvian, Lettish TI Tigrinya
BR Breton MG Malagasy TK Turkmen
CA Catalan MI Maori TL Tagalog
CO Corsican MK Macedonian TN Setswana
CS Czech ML Malayalam TO Tonga
CY Welsh MN Mongolian TR Turkish
DA Danish MO Moldavian TS Tsonga
DZ Bhutani MR Marathi TT Tatar
EL Greek MS Malay (MAY) TW Twi
EO Esperanto MT Maltese UK Ukrainian
ET Estonian MY Burmese UR Urdu
EU Basque NA Nauru UZ Uzbek
FA Persian NE Nepali VI Vietnamese
FI Finnish NL Dutch VO Volapuk
FJ Fiji NO Norwegian WO Wolof
FO Faroese OC Occitan XH Xhosa
FY Frisian OM (Afan) Oromo YO Yoruba
GA Irish OR Oriya ZU Zulu
GD Scots Gaelic PA Panjabi
GL Galician PL Polish
GN Guarani PS Pashto, Pushto
GU Gujarati PT Portuguese
HA Hausa QU Quechua
HI Hindi RM Rhaeto-Romance
HR Croatian RN Kirundi
HU Hungarian RO Rumanian
HY Armenian RW Kinyarwanda
IA Interlingua SA Sanskrit
IE Interlingue SD Sindhi
IK Inupiak SG Sangho
IN Indonesian SH Serbo-Croatian
IS Icelandic SI Singhalese
IW Hebrew SK Slovak
JI Yiddish SL Slovenian
42
OPTICAL DIGITAL OUT Signals
DIGITAL AUDIO
Output Signals
OUTPUT
Playback disc/file STREAM/PCM DOLBY DIGITAL/PCM PCM ONLY
DVD Video
with 48 kHz, 16/20/24 bit Linear PCM 48 kHz, 16 bit Linear PCM*
with 96 kHz, Linear PCM 48 kHz, 16 bit Linear PCM
with Dolby Digital Dolby Digital bitstream 48 kHz, 16 bit Linear PCM
with DTS DTS bitstream 48 kHz, 16 bit Linear PCM
DVD Audio
with 48/96/192 kHz, 16/20/24 bit 48 kHz, 16 bit Linear PCM
Linear PCM
with 44.1/88.2/176.4 kHz,
44.1 kHz, 16 bit Linear PCM
16/20/24 bit Linear PCM
with DTS DTS bitstream 48 kHz, 16 bit Linear PCM
DVD-R/-RW/-ROM in DVD-VR format
with 48 kHz, 16/20/24 bit Linear PCM 48 kHz, 16 bit Linear PCM*
SVCD, VCD, CD 44.1 kHz, 16 bit Linear PCM/48 kHz, 16 bit Linear PCM
CD with DTS DTS bitstream 44.1 kHz, 16 bit Linear PCM
MP3/WMA/WAV/MPEG-1/
32/44.1/48 kHz, 16 bit Linear PCM
MPEG-2 disc/file
DivX disc/file
with MP2, MP3 32/44.1/48 kHz, 16 bit Linear PCM
with Dolby Digital 32/44.1/48 kHz,
Dolby Digital bitstream
16 bit Linear PCM
ASF disc/file 32 kHz, 16 bit Linear PCM
* While playing some DVDs, digital signals may be emitted at 20 bits or 24 bits (at their original bit rate) through the OPTICAL DIGITAL
OUT terminal if the discs are not copy-protected.
Operating JVC’s TVs Using the Remote Control

You can use the remote control to operate JVC’s TVs.
Remote control
TV Turn on/off TV.
TV/VIDEO Change the input mode.
TV While holding SHIFT, press...

TV/VIDEO TV VOL +,– Adjust the volume.
TV CH , Change the channels.

TV CH ,
TV VOL
SHIFT +,–
43
Specifications General
Power requirement:
Amplifier section—CA-UXG68 AC 110 V/AC 127V/AC 220 V/AC 230 V-240V
Output Power: (adjustable with the voltage selector), 50 Hz/60 Hz
120 W (60 W + 60 W) at 6 Ω (10% THD) For Oceanian countries: AC 240 V , 50 Hz
Audio Input AUX: 500 mV/50 kΩ (at “AUX LVL1”) Power consumption: 125 W (at operation)
250 mV/50 kΩ (at “AUX LVL2”) 14 W (at standby)
125 mV/50 kΩ (at “AUX LVL3”) 3.5 W (at standby dimmer OFF mode)
Digital output: OPTICAL DIGITAL OUT: Dimensions (approx.): 170 mm x 250 mm x 342 mm
–21 dBm to –15 dBm (660 nm ±30 nm) (W/H/D)
Digital input: USB MEMORY Mass (approx.): 5.7 kg
Video Out: Speaker section—SP-UXG68
Color system: NTSC or PAL (interlaced/progressive) Speaker units: Tweeter: 1.5 cm dome x 1
VIDEO (composite): 1 V(p-p)/75 Ω Squawker: 4 cm cone x 1
S-VIDEO: Y (luminance) 1 V(p-p)/75 Ω Woofer: 13.5 cm cone x 1
C (chrominance, burst) Impedance: 6Ω
NTSC 0.286 V(p-p)/75 Ω Dimensions (approx.): 166 mm x 250 mm x 232 mm
PAL 0.3 V(p-p)/75 Ω (W/H/D)
COMPONENT: (Y) 1 V(p-p)/75 Ω Mass (approx.): 2.8 kg each
(PB/PR) 0.7 V(p-p)/75 Ω Supplied Accessories
Speaker impedance: 6 Ω – 16 Ω See page 3.
Tuner section Design and specifications are subject to change without notice.
FM tuning range: 87.50 MHz – 108.00 MHz • Manufactured under license from Dolby Laboratories. “Dolby”,
AM (MW) tuning range: “Pro Logic”, “MLP lossless”, and the double-D symbol are
531 kHz – 1 710 kHz (at 9 kHz intervals) trademarks of Dolby Laboratories.
530 kHz – 1 710 kHz (at 10 kHz intervals) • “DTS” is a registered trademark of DTS, Inc. and
For Saudi Arabia only: “DTS2.0+Digital Out” is a trademark of DTS, Inc.
531 kHz – 1 602 kHz (at 9 kHz intervals) • “Official DivX® Certified product” “Plays all versions of DivX®
video (including DivX® 6) with standard playback of DivX®
530 kHz – 1 600 kHz (at 10 kHz intervals) media files” “DivX, DivX certified, and associated logos are
Tape section trademarks of DivX, Inc. and are used under licence.”
Frequency response: 60 Hz – 14 000 Hz • “Official DivX® Ultra Certified product” “Plays all versions of
Wow and flutter: 0.15 % (WRMS) DivX® video (including DivX® 6) with enhanced playback of
DivX® media files and the DivX® Media Format” “DivX, DivX
Disc/file player section Ultra Certified, and associated logos are trademarks of DivX, Inc.
Region codes: and are used under licence.”
Middle East: 2 • Microsoft and Windows Media are either registered trademarks or
South East Asia: 3 trademarks of Microsoft Corporation in the United States and/or
Central and South America, Australia: 4 other countries.
Playable disc: • USE OF THIS PRODUCT IN ANY MANNER THAT
COMPLIES WITH THE MPEG-4 VISUAL STANDARD IS
DVD Video/DVD Audio/CD/VCD/SVCD/ PROHIBITED, EXCEPT FOR USE BY A CONSUMER
CD-R/CD-RW (CD/SVCD/VCD/MP3/ ENGAGING IN PERSONAL AND NON-COMMERCIAL
WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/ ACTIVITIES.
DivX format) • This product incorporates copyright protection technology that is
DVD-R/-RW (DVD-VR/DVD Video/MP3/ protected by U.S. patents and other intellectual property rights.
WMA/WAV/JPEG/MPEG-1/MPEG-2/ASF/ Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
DivX format) uses only unless otherwise authorized by Macrovision. Reverse
+R/+RW (DVD Video/MP3/WMA/WAV/ engineering or disassembly is prohibited.
JPEG/MPEG-1/MPEG-2/ASF/DivX format) “CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DVD-ROM (MP3/WMA/WAV/JPEG/ DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
MPEG-1/MPEG-2/ASF/DivX format) WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625
Playable file: PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/ RECOMMENDED THAT THE USER SWITCH THE
ASF/DivX format CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT.
Dynamic range: 80 dB IF THERE ARE QUESTIONS REGARDING OUR TV SET
Horizontal resolution: 500 lines COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD
Wow and flutter: Immeasurable PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE
CENTER.”
44
Parts Index
Remote control x UP, DOWN 4 9& 8, 20
Button Page USB MEMORY jack ( 5
AUDIO g 7 USB MEMORY #/8 4 7, 10, 27, 28, 29, 31
TV h 43 VOLUME + , – % 12, 30, 31
7 t 10, 11, 18, 20, 27, 28, 29
y,1 u 9, 10 Remote control
x,4 , 9, 10, 11, 20, 27
8 y 10, 18, 20, 27, 29 1
, , , , ENTER/SET q 9, 11, 14, 15, 18, 23, 25, 27, 33, 34, 35 2
(One-Touch Replay) n 18 f
3
3D PHONIC 5 13 4 g
AHB PRO ; 12 5 1 2 3 h
ANGLE 7 17 j
AUDIO/MPX o 16, 30 4 5 6
AUDIO VOL + , – Q 7, 12
6 k
A.STANDBY f 15 7 7 8 9
l
BASS/TREBLE E 13 8 10 0 10 /
C.VOICE 4 18 9 z
CANCEL 9 20, 34 p
CLOCK/TIMER j 15, 33, 34 x
DIMMER 3 14
q
DISPLAY / 15 w
e c
DVD/AUX LEVEL a 13
r v
DVD/CD 3 r 7, 10, 27
ECHO* x 31 t b
FADE MUTING W 12 y n
FM/PLAY MODE . 8, 19, 20 m
FM/AM/AUX b 7, 8, 28 u ,
GROUP/TITLE m 10, 27 i .
GROUP/TITLE SKIP , 10 P
KARAOKE* c 31 o
KEY , * q 31 ; Q
MENU/PL x 11, 25
Number buttons 1 9, 11, 18, 19, 24, 25
a W
ON SCREEN c 23 s
PAGE i 17 E
QP LINK ; 11
d
REPEAT P 21
REPEAT A-B P 21
RESERVE* w 32
RETURN 8 11
This remote control can also operate JVC’s TVs
SCAN MODE l 14 (see page 43).
SET UP w 35
SHIFT s 10, 11, 13, 14, 15, 17, 18, 21, 27, 31, 32, 33, 34, 43
Main unit
SLEEP 2 15
SLOW 9 , ( u 18
SOUND TURBO II d 12
SUBTITLE i 17
TAPE v 7
TOP MENU/PG p 11, 25
TV CH 9 , ( q 43
TV VOL + , – Q 43
TV/VIDEO k 43
USB MEMORY 3 e 7, 10, 27, 28, 29, 31
VFP z 14
ZOOM 6 18, 27
Main unit
Button Page
& STANDBY lamp 8 7
7 0 10, 21
0 ^ 10, 21
3D PHONIC/HP SURROUND $ 13
AUX jack * 5
Cassette holder ~ 9, 28
Display 3 6
DISPLAY 6 15
DVD/CD #/8 5 7, 10, 27, 28, 29, 31
FM/AM/AUX ! 7, 8, 28
MIC jack* 1 30, 31
MIC VOLUME* = 30, 31
PHONES - 7 * Not on the Australian model.
REC # 28, 29, 30
Remote sensor 2 5
SOUND TURBO II 7 12
TAPE @ 10
45
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada,
Australia, and U.K.)
UX-G68
MICRO COMPONENT SYSTEM
CAUTION for mains (AC) line
BEFORE PLUGGING IN, do check
that your mains (AC) line voltage
corresponds with the position of the
voltage selector switch provided on
the outside of this equipment and, if
different, reset the voltage selector
switch, to prevent from a damage or
risk of fire/electric shock.
EN
© 2007 Victor Company of Japan, Limited 0207WMKMDCJEM

JVC SP Uxg68

Uploaded by

Copyright:

Available Formats

JVC SP Uxg68

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

JVC SP Uxg68

Uploaded by

Copyright:

Available Formats

MICRO COMPONENT SYSTEM

UX-G68 —Consists of CA-UXG68 and SP-UXG68

IMPORTANT FOR LASER PRODUCTS

Caution: Proper Ventilation

SP-UXG68 CA-UXG68 SP-UXG68 CA-UXG68

[European Union only]

Others Audio/Video File Operations ................................ 26

“DVD Logo” is a trademark of DVD Format/Logo

~ From AM/FM antenna

Ÿ From the speakers

! From the powered subwoofer

From the input of TV/monitor

From the portable audio device

Press and hold

To connect AM/FM antenna

! To connect the powered subwoofer

The subwoofer connected can reproduce the bass sounds

Before plugging in the System

@ Digital audio component 220V 230V

Protective cap Preparing the remote control

• Set “DIGITAL AUDIO OUTPUT” in the “AUDIO” menu

When connecting a portable audio device (AUX) R6(SUM-3)/AA(15F)

DO NOT recharge, short, disassemble, heat

When using the remote control

QPLink S V C D V D MP3 WMA 3DPHONIC L-BANDIII AM FM

1 QP Link (Quick Portable Link) indicator e AHB PRO indicator

You can reduce power consumption by pressing DIMMER

For private listening

DO NOT turn off (standby) the System with

1 Select the AM band. To tune in to a station

2 Turn off the power.

Frequency starts changing on the display.

• Finish the following process while the indication on

• You can also use the y or 1 button.

To rewind/fast-forward the tape:

Examples: Main unit:

press 5. Rewind the tape.

• You can also use the y or 1 button.

• When using an 8 cm disc, place it on the inner circle of the

To return to the previous menu:

menu. Playback of the selected item starts.

VOLUME +,– AHB OFF

To adjust the tone ONLY

3D PHONIC ACTION 3D PHONIC DRAMA

movies in a relaxed mood. You can dim the display window.

GAMMA Adjust if the neutral color is bright or

To check the current clock time during play

While playing a DVD Audio/DivX...

While playing a DVD-VR, or SVCD/VCD...

ST1/ST2/ To listen to normal stereo (2-channel)

1/3 2/3 3/3

For DVD Audio only: While playing back a track linked to

SUBTITLE Playing Back Bonus Group Remote

1 Select the bonus group.

Reverse slow motion* starts.

Special Effect Playback Remote

2 Move the zoomed-in position.

2 Advance the still picture frame by frame.

To resume normal playback, press DVD/CD 3.