CCNA 2 Chapter 1

Name:__________________________
CCNA 2 Chapter 1: WANs and Routers
One major characteristic of a wide-area network (WAN) is that the network operates
beyond the local LAN's geographic scope. It uses the services of carriers, such as
regional Bell operating companies (RBOCs), Sprint, and MCI.
WANs use serial connections of various types to access bandwidth over wide-area
geographies. By definition, the WAN connects devices that are separated by wide areas.
WAN devices include the following:
• Routers, which offer many services, including internetworking and WAN
interface ports
• Switches, which connect to WAN bandwidth for voice, data, and video
communication
• Modems, which interface voice-grade services and channel service units/digital
service units
• Channel service units/data service units (CSUs/DSUs) that interface T1/E1
services and Terminal Adapters/Network Termination 1 (TA/NT1s)
• TA/NT1s that interface Integrated Services Digital Network (ISDN) services
• Communication servers, which concentrate on dial-in and dial-out user
communication
Concept Questions
Demonstrate your knowledge of these concepts by answering the following questions in
the space provided.
1. A WAN is used to interconnect local-area networks (LANs) that are typically
separated by a large geographic area. A WAN operates at the OSI reference
model physical and data link layers. The WAN provides for the exchange of
data packets/frames between routers/bridges and the LANs that they
support. Draw a WAN that includes three LANs.
2. Compare and contrast WANs and LANs layer by layer.
3. Routers and the modern PC have many hardware components in common.

Which components are shared by a PC and a router?
4. There are many steps that must occur to communicate with a router using a
PC. Explain both the hardware and software components needed to establish
a terminal session with a Cisco router.
Vocabulary Exercise
Define the following terms as completely as you can. Refer to the online curriculum or
CCNA 2 Chapter 1 from the Cisco Networking Academy Program CCNA 1 and 2
Companion Guide, Revised Third Edition, for help.
• Auxiliary port
• Console port
• CSU (channel service unit)
• DCE (Data Communications Equipment (EIA expansion) or data circuit
terminating
• equipment (ITU-T expansion)
• DSU (data service unit)
• DTE (data terminal equipment)
• E1--
• Frame Relay--
• HDLC (High-Level Data Link Control)--
• ISDN (Integrated Services Digital Network)--
• PPP (Point-to-Point Protocol)--
• PTT (Post, Telephone, and Telegraph)--
• RBOC (Regional Bell Operating Company) --
• T1--
Focus Questions
1. Name and briefly describe four WAN devices.
2. Name two ways in which WANs differ from LANs.
3. What do the acronyms DTE and DCE stand for?
4. List three WAN physical layer standards.
5. List four WAN data link layer protocols.
6. List the two ports on a router that you can use to enter an initial
configuration.
7. List the settings used in HyperTerminal to connect to the console port of a

Cisco router.
8. What is the purpose of NVRAM on a Cisco router?
9. What is the purpose of RAM on a Cisco router?

10. What is the purpose of Flash on a Cisco router?
CCNA Exam Review Questions

The following questions help you review for the CCNA exam.
Highlight the correct answer in red.
1. Which of the following best describes a WAN?

A. It connects LANs that are separated by a large geographic area.
B. It connects workstations, terminals, and other devices that are in a
metropolitan area.
C. It connects LANs that are within a large building.
D. It connects workstations, terminals, and other devices that are within a
building.
2. Which of the following are WAN technologies?

A. Token Ring and ARCnet
B. Frame Relay and SMDS
C. Star and Banyan VINES
D. CSU/DSU and ARCview
3. What service does a WAN provide to LANs?

A. High-speed multiple access to data networks
B. IP addressing and secure data transfer
C. Exchange of data packets between routers and the LANs those
routers support
D. Direct routing with error checking
4. What type of connections do WANs use that LANs typically do not use?
A. Parallel, lower speed
B. Multiple, higher speed
C. Multiple, lower speed
D. Serial, lower speed
5. At which layers of the OSI model does a WAN operate?

A. Physical and application
B. Physical and data link
C. Data link and network
D. Data link and presentation
6. Which layers of the OSI model do WAN standards describe?

A. Data link and network
B. Data link and presentation
C. Physical and application
7. How do WANs differ from LANs?
A. WANs typically exist in defined geographic areas.
B. WANs provide high-speed multiple access services.
C. WANs use tokens to regulate network traffic.
D. WANs use services of common carriers.
8. How are operational and functional connections for WANs obtained?

A. From your local telephone company
B. From InterNIC
C. From RBOCs
D. From the WWW Consortium (W3C)
9. What do the WAN physical layer standards describe?

A. Interface between SDLC and HDLC
B. How frames are sent and verified
C. How voice and data traffic are routed
D. Interface between DTE and DCE
10. Which of the following best describes what WAN data link protocols define?
A. How frames are carried between systems on a single data link
B. Methods for determining optimum path to a destination
C. How data packets are transmitted between systems on multiple data links
D. Methods for mapping IP addresses to MAC addresses
11. Which of the following is a WAN data link protocol?

A. TCP/IP
B. Point-to-Point Protocol
C. EIGRP
D. OSPF
12. Which of the following best describes data terminal equipment (DTE)?
A. It is a physical connection between networks and users.
B. It generates clocking signals to control network traffic.
C. It is a device at the user end of a network.
D. It is a physical device such as a modem and interface card.
13. Which of the following is an example of DTE?

A. Interface card
B. Modem
C. Computer
D. CSU/DSU
14. Which of the following best describes data circuit-terminating equipment (DCE)?
A. It is a device at the user end of a network.
B. It serves as the data source or destination.
C. It is physical devices such as protocol translators and multiplexers.
D. It is a physical connection between networks and users.
15. Which is an example of DCE?

A. Multiplexer
B. Modem
C. Translator
D. Computer
16. Which of the following best describes High-Level Data Link Control (HDLC)?
A. It is a digital service that transmits voice and data over existing phone
lines.
B. It uses high-quality digital facilities and is the fastest WAN protocol.
C. It provides router-to-router and host-to-network connections over
synchronous and asynchronous circuits.
D. It supports point-to-point and multipoint configurations and uses
frame characters and checksums.
17. Which WAN protocol can be described as supporting point-to-point and

multipoint configurations?
A. HDLC
B. Frame Relay
C. PPP
D. ISDN
18. Which WAN protocol can be described as using frame characters and checksums?
A. ISDN
B. Frame Relay
C. PPP
D. HDLC
19. Which of the following best describes Frame Relay?

A. It uses high-quality digital facilities and is the fastest WAN protocol.
B. It supports point-to-point and multipoint configurations, and it uses frame
characters and checksums.
C. It is a digital service that transmits voice and data over existing telephone
lines.
D. It provides router-to-router and host-to-network connections over
20. Which of the following are not used in a WAN?
A. Hub
B. Modem
C. Router
D. Communications server
21. Which WAN protocol can be described as the fastest WAN protocol?
A. HDLC
B. PPP
C. Frame Relay
D. ISDN
22. Which of the following best describes PPP?

A. It uses high-quality digital facilities and is the fastest WAN protocol.
B. It supports point-to-point and multipoint configurations, and it uses frame
C. It provides router-to-router and host-to-network connections over
D. It is a digital service that transmits voice and data over existing telephone
lines.
23. Which WAN protocol can be described as providing router-to-router and host-
tonetwork
connections over synchronous and asynchronous circuits?
A. HDLC
B. Frame Relay
C. PPP
D. ISDN
24. Which of the following best describes ISDN?

A. It is a digital service that transmits voice and data over existing phone
lines.
B. It provides router-to-router and host-to-network connections over
C. It uses high-quality digital facilities and is the fastest WAN protocol.
D. It supports point-to-point and multipoint configurations, and it uses frame
25. Which of the following is stored in NVRAM?

A. The active Cisco IOS software image
B. The backup configuration file for the router
C. The backup Cisco IOS software image
D. The active routing table
26. Which of the following cannot be accomplished using the console port?
A. Troubleshoot problems
B. Monitor the system
C. Configure the router
D. Capture data packets from a LAN
27 no question free points!
28. What type of cable do you use to connect a PC to the console port?
A. Patch cable
B. Rollover
C. Crossover
D. EIA/TIA 568B
29. What type of cable do you use to connect a PC to a switch?

A. Patch cable
B. Rollover
C. Crossover
D. EIA/TIA 568B
30. What type of cable do you use to connect a switch to a hub?

A. Patch cable
B. Rollover
C. Crossover
D. EIA/TIA 568B

CCNA 2 Chapter 1

Uploaded by

Copyright:

Available Formats

CCNA 2 Chapter 1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CCNA 2 Chapter 1

Uploaded by

Copyright:

Available Formats

Name:__________________________

CCNA 2 Chapter 1: WANs and Routers

2. Compare and contrast WANs and LANs layer by layer.

3. Routers and the modern PC have many hardware components in common.

2. Name two ways in which WANs differ from LANs.

3. What do the acronyms DTE and DCE stand for?

4. List three WAN physical layer standards.

5. List four WAN data link layer protocols.

7. List the settings used in HyperTerminal to connect to the console port of a

8. What is the purpose of NVRAM on a Cisco router?

9. What is the purpose of RAM on a Cisco router?

CCNA Exam Review Questions

1. Which of the following best describes a WAN?

2. Which of the following are WAN technologies?

3. What service does a WAN provide to LANs?

5. At which layers of the OSI model does a WAN operate?

6. Which layers of the OSI model do WAN standards describe?

8. How are operational and functional connections for WANs obtained?

9. What do the WAN physical layer standards describe?

11. Which of the following is a WAN data link protocol?

13. Which of the following is an example of DTE?

15. Which is an example of DCE?

17. Which WAN protocol can be described as supporting point-to-point and

19. Which of the following best describes Frame Relay?

22. Which of the following best describes PPP?

24. Which of the following best describes ISDN?

25. Which of the following is stored in NVRAM?

27 no question free points!

29. What type of cable do you use to connect a PC to a switch?

30. What type of cable do you use to connect a switch to a hub?

You might also like