STAINLESS STEEL STOP LOGS

SERIES 95
STOP LOGS
Low leakage rate
Installation in new or existing channel
Sealing system completely mounted on log
***

The Fontaine SERIES 95 Stop Logs are an easy and economical way to control flow in a channel. Their
lightweight construction makes them easy to handle and the UHMWPE (ultra high molecular weight
polyethylene) guide eliminates all metal-to-metal contact between the slide and frame, thereby
allowing the logs to slide up and down with minimal friction.

Stainless Steel Construction Reinforced Log

Because of its stainless steel construction, the The log consists of a stainless steel plate
SERIES 95 has high corrosion and erosion reinforced with horizontal members welded to
resistance, and can be operated many years with the plate, making it a solid one-piece log.
minimum maintenance. Stainless steel allows
design flexibility and strength.

Stainless Steel Frame

The stainless steel frame on the SERIES 95 is a
stainless steel channel designed to be
embedded in a channel (FE) (Figure 95-01) or to
be anchored on the surface of an existing
channel (EC) (Figure 95-02). The sill can be flush
bottom or located on the surface of the channel.
The frame can also be mounted on a concrete
wall (CW)(Figure 95-03).

UHMWPE Guides and EPDM Seals

The seals on the SERIES 95 are installed on the
log. The UHMWPE guide is on the side of the log
and holds the EPDM seal. The log is sealed at all
times, even with a small water head behind it.
The bottom seal is made of a soft piece of EPDM
that seals on the sill or on top of another log. All
logs are manufactured to be interchangeable.

Effective 03/04 Section 6 PCode S95 Page 1 of 7

 STAINLESS STEEL STOP LOGS

SERIES 95
STOP LOGS

A A

CHANNEL
HEIGHT

FLOW

B
CHANNEL WIDTH
FRAME WIDTH
BOXOUT WIDTH Figure 95-01
Frame embedded arrangement of a set of
Stop Logs and frame (FE)
D

EPDM
SEAL

FRAME
W
FRAME
GROUT

ADJUSTING NUTS
FLOW TO LEVEL FRAME
BEFORE GROUTING W
Detail 95-01
Detail 95-02
Side section “A-A” of a frame embedded
Bottom section “B-B” of a frame embedded

Effective 07/98 Section 6 PCode S95 Page 2 of 7

 STAINLESS STEEL STOP LOGS

SERIES 95
STOP LOGS

OPENING

FRAME

A A

CHANNEL
HEIGHT

FLOW

INVERT
B
FRAME WIDTH
CHANNEL WIDTH ANCHOR

Figure 95-02
Channel mounted arrangement of a
stop logs and frame (EC)

EPDM
SEAL
EPDM SEAL

UHMWPE
SIDE SEAL
EPDM GASKET
FLOW

STIFFENER
GROUT
Detail 95-03
Detail 95-04
Side section “A-A” of a frame in channel
Bottom section “B-B” of a frame in channel

Effective 01/99 Section 6 PCode S95 Page 3 of 7

 STAINLESS STEEL STOP LOGS

SERIES 95
STOP LOGS

A A

CHANNEL
HEIGHT

INVERT

CHANNEL WIDTH
FRAME WIDTH
Figure 95-03
Wall mounted arrangement of a set
of stop logs and frame (CW)

ANCHOR S.S. LOG

EPDM SEAL EPDM
BOTTOM SEAL
LOG

EPDM GASKET
EPDM GASKET
S.S. FRAME
UHMWPE GUIDE

Detail 95-05
Side section “A-A” of a wall mounted Detail 95-06
Bottom section “B-B” of a wall mounted

Effective 05/98 Section 6 PCode S95 Page 4 of 7

 STAINLESS STEEL STOP LOGS

SERIES 95
STOP LOGS

Also available is a lifting device to reach the logs

at a lower elevation. The lifting device is
fabricated in stainless steel and is adjusted to fit
in the stop log’s frame. Cable to disengage the hooks
A

Section “A-A”
A
Figure 95-04

Frame width

Frame embedded Channel width + 5 1/2" (140 mm)

Log width Max Log thickness
Existing channel Channel width - approx. 1" (25 mm) (inches / mm ) (inches / mm )
0 - 84 4,5
Wall mounted Channel width + 8" (203 mm) 0 - 2134 115
85 - 102 5,5
2159 - 2591 140
Log width 103 - 120 6,5
2617 - 3048 165
Frame embedded Channel width + 4 1/4" (108 mm)

Existing channel Frame width - 1 1/4" (32 mm)

Concrete box-out minimum dimensions W x D

Size Channel less than 84" (2134 mm) wide Channel equal to or more than 84" (2134 mm) wide

Bottom = 8 1/4" (210 mm) wide x 3 1/4" (83 mm) deep 9 1/4" (235 mm) wide x 3 1/4" (83 mm) deep

Sides = 8 1/4" (210 mm) wide x 3 3/4" (95 mm) deep 9 1/4" (235 mm) wide x 3 3/4" (95 mm) deep

(*) These dimensions are for information only. Do not use for installation or submittal purposes.

Effective 03/04 Section 6 PCode S95 Page 5 of 7

 STAINLESS STEEL STOP LOGS

SERIES 95
STOP LOGS

1. GENERAL CONDITIONS 2. PERFORMANCE

1.1. SCOPE. This section covers Stainless Steel Stop 2.1. LEAKAGE. Stop logs shall be substantially
Logs. watertight under the design head conditions. Leakage
shall not exceed 0.1 U.S. gallon per minute per foot
1.2. GENERAL. The equipment provided under this (1.25 l/min per meter) of periphery for the rated seating
section shall be fabricated, assembled, erected, and head.
placed in proper operating condition in full conformity
with the drawings, specifications, engineering data, 2.2. DESIGN HEAD. For the purpose of these
instructions and recommendations of the equipment specifications, stop logs shall be defined as meeting
manufacturer unless exceptions are noted by the the leakage requirements maximum water level (height
engineer. of stop logs in channel).

Stop logs shall be supplied with all the necessary parts 3. PRODUCT
and accessories indicated on the drawings, specified
or otherwise required for a complete, properly
operating installation, and shall be the latest standard 3.1. STOP LOGS
product of a manufacturer regularly engaged in the
production of stop logs. 3.1.1. GENERAL DESIGN. Stop logs shall be
constructed entirely of stainless steel. All hardware
The stop logs supplied under this section shall be shall be stainless steel.
Series 95 Stainless Steel Stop Logs as manufactured
by H. Fontaine Ltd. 3.1.2. FRAME. The frame shall be made of stainless
steel channels. The frame shall be suitable for
1.3. QUALITY ASSURANCE mounting on a concrete wall (CW), embedding in a
channel (FE), or installation inside an existing channel
1.3.1. The manufacturer shall have experience in the (EC).
production of substantially similar equipment and shall
show evidence of satisfactory operation in at least 5 3.1.3. LOGS. The logs shall consist of a flat plate
installations. The manufacturer's shop welds, welding reinforced with formed plates or structural members to
procedures and welders shall be qualified and certified limit their deflection to 1/360 of the gate's span under
in accordance with the requirement of the latest edition the design head. The guide shall be of UHMWPE (ultra
of ASME, Section IX. high molecular weight polyethylene).

1.3.2. The fully assembled stop logs shall be shop 3.1.5. SEALS. Seals shall be made of EPDM attached
inspected before shipping. to the logs by means of a UHMWPE retainer guide. The
bottom seal is attached to the log with a stainless steel
1.3.3. The manufacturer shall be ISO 9001 : 2000 retainer and seal on top of the log immediately
certified. underneath.

1.4. SUBMITTALS. The manufacturer shall submit, for 3.2. LIFTING DEVICE. When required, a stainless
approval by the purchaser, drawings showing the steel lifting device shall be supplied for each log width.
principal dimensions, general construction and The width of the lifting device will be the same as the log
materials used in the gate and lift mechanism. channel. The lifting device shall be equipped with a
device to allow releasing of the stop log from the
operating floor. This device shall grab the log
automatically.

Effective 03/04 Section 6 PCode S95 Page 6 of 7

 STAINLESS STEEL STOP LOGS

SERIES 95
STOP LOGS

4. MATERIALS
Part Material

Frame, log, reinforcements Stainless steel ASTM A-240

bottom seal retainer Type 304L or 316L

Guide Ultra high molecular weight

polyethylene (UHMWPE)
ASTM D-4020
Seal EPDM ASTM D-2000

Fasteners ASTM F593 and F594

GR1 for type 304 and
GR2 for type 316

5. SCHEDULE

Stop log
Identification
Channel
width
Channel invert
elevation

Top of channel
elevation

Mounting:
FE - Frame-embedded
EC - Existing channel
CW - Concrete wall mounted

6. EXECUTION

6.1. INSTALLATION. Gates and appurtenances shall

be handled and installed in accordance with the
manufacturer's recommendations.

Effective 03/04 Section 6 PCode S95 Page 7 of 7