Educational Note: Measuring With Digital Storage Oscilloscopes

Measuring with digital storage
oscilloscopes
Educational note
Products:
ı R&S®HMO1002
This educational note covers the theory and practice of digital

storage oscilloscopes based on concrete measurement examples
that address authentic everyday tasks.
The theoretical portion of this paper begins with an explanation of
the basic operating concepts for digital oscilloscopes. This is
followed by a discussion of the most important parameters to be
considered when setting up and performing the exercise
measurements. The final portion of the theoretical section prepares
the reader for the subsequent practical exercises.
The practical portion of the educational note contains detailed
measurement tasks that can be performed by small groups in the
university lab. These exercises are intended to demonstrate and
reinforce the knowledge gained in the theoretical portion. The
exercises build upon one another and show the students
measurement tasks that are encountered frequently by engineers
in their daily work.
Please find the most up-to-date document on our homepage

http://www.rohde-schwarz.com/appnote/1MA265
2.2016 – 1MAA265-1e
M. Reil, R. Wagner
Educational note
Contents
Contents 1 Basics ....................................................................................................... 4

1.1 Operation ......................................................................................................................5
1.1.1 Operating concept and default settings .........................................................................5
1.1.2 Signals and bandwidth ...................................................................................................7
1.1.3 Probes ............................................................................................................................8
1.2 Configuration .............................................................................................................11
1.2.1 Vertical resolution and dynamic range.........................................................................12
1.2.2 Signal sampling and processing ..................................................................................12
1.2.3 Triggering basics..........................................................................................................16
2 Preparing for the measurement exercises ..................................... 18
3 Basic measurements ........................................................................ 20

3.1 Exercise setup............................................................................................................20
3.2 Exercise ......................................................................................................................21
4 Documentation and storage ............................................................ 27

4.1 Exercise setup............................................................................................................27
4.2 Exercise ......................................................................................................................28
5 Advanced trigger settings................................................................ 32

5.1 Exercise setup............................................................................................................32
5.2 Exercise ......................................................................................................................33
6 Signal analysis using FFT ................................................................ 38

6.1 Exercise setup............................................................................................................38
6.2 Exercise ......................................................................................................................39
7 Analysis of protocol-based bus signals ......................................... 43

7.1 Test setup ...................................................................................................................43
7.2 Exercise ......................................................................................................................44
8 Reference .......................................................................................... 49
A.1 Appendix 1 The training board .....................................................................................50
1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 2

Contents
The following abbreviation are used in this Educational Note for Rohde & Schwarz test
equipment:
ı The R&S®HMO1002 Digital Oscilloscope is referred to as the HMO1002

Basics
1 Basics
Oscilloscopes are among the most versatile test instruments available for analyzing
and testing analog and digital circuits. Because they can display and analyze a broad
spectrum of electronic signals, digital storage oscilloscopes are used for a wide variety
of research and development applications.
Although modern oscilloscopes support automated assignment of all parameters, it is
essential for users to develop a fundamental understanding of the function and
operation of the test instruments. The high degree of automation over the entire
measurement process leaves many users entirely dependent on the results delivered
by the instrument, while the logic behind the measurements remains a mystery to
these users. Thorough practical knowledge is needed in order to assess the validity of
results. The purpose of this educational note is to provide the foundation for the correct
performance of typical measurement tasks.
The descriptions and exercises are applicable for modern storage oscilloscopes. The
R&S®HMO1002 as shown in Fig. 1 was used for all theoretical descriptions and
practical exercises.
The contents for this chapter are drawn in part from the manual for the R&S®RTO
oscilloscope (1) CITATION Roh15 \l 1031 and from "Oscilloscope Fundamentals" from
Rohde & Schwarz (2) CITATION Roh \l 1031.
Fig. 1: The R&S®HMO1002 digital storage oscilloscope.

Basics
1.1 Operation
This section introduces the most important settings for oscilloscope measurements and
describes the instrument operation. The reader should also gain a feeling for the
selection of both a suitable test setup and the necessary hardware for obtaining
reproducible and accurate results.
1.1.1 Operating concept and default settings
An oscilloscope typically displays a given variable as a function of another variable.

The most typical use case is the display of voltage versus time, where nearly all
phenomena can be converted to electrical signals by using an appropriate converter.
Oscilloscopes usually have at least two independent channels, making it possible for
example to reproduce the voltage from channel 2 over the voltage from channel 1. See
section 3.2 for a related use case. Either the vertical or horizontal system is used for
scaling the axes in the display.
The vertical system includes all settings affecting the scaling of the amplitude or the
vertical offset of the signal. The horizontal system, on the other hand, can be used to
influence the temporal offset and the resolution in parts of a second.
Beyond these basic settings, the trigger system is also key. Triggers can be used to
define the conditions under which the oscilloscope should start a measurement. This
ensures a stable signal display that always shows the segments of interest.
All of these settings are described in more detail in the preparatory test setup sections
of chapter 3.
The groupings controlling these settings can be seen based on the example of the
HMO1002 (see Fig. 1). Together with the setting options for the trigger system (see
section 1.2.3), the groupings for the vertical and horizontal display take up the entire
lower two-thirds of control area. The HMO1002 additionally provides buttons for
system-specific settings, specialized measurement tasks and automated analysis.
The HMO1002 display is divided into 12 horizontal and 8 vertical units. This allows the
user to make a quick visual assessment of the readings and to scale the axes. See
Fig. 2 for an introduction into the functionality for the horizontal and vertical systems.
The scaling for the vertical system is set using the large rotary knob labeled
VOLTS/DIV ( Fig. 2, right). The associated vertical scaling is displayed at the left,
under the signal for each active channel. For example, 50 mV means that the height of
one grid square is equal to 50 mV1. This setting then equals a vertical display over the
entire range of 50 mV * 8 = 400 mV.
1 This corresponds to 50 mV/div, where div is the abbreviation for 'division'.

Basics
Fig. 2: Basic settings for the horizontal and vertical systems.
The timebase is set in a similar fashion using the TIME/DIV rotary knob ( Fig. 2,
right). In the example provided in Fig. 2, 10 µs is the length of one grid square.
Consequently, the duration of the displayed signal is 10 µs * 12 = 120 µs. Unlike the
amplitude scaling, this setting applies to all channels. The rotary knobs labeled
POSITION set the offsets for the vertical and horizontal systems.
For example, Fig. 3 shows the measurement of two single-ended, square-wave signals
using the HMO1002. The timebase is 10 µs. As a result, one period of the signal
measured with channel 1 (yellow, top) is 20 µs in duration. This means that this is a
50 kHz signal. As mentioned above, the timebase applies to all channels. A visual
analysis will therefore immediately lead to the conclusion that the signal acquired with
channel 2 (blue, bottom) is at one-half the frequency. On the other hand, it can also be
observed that, as a result of the different vertical scalings, there is no distinction
between the two signals with respect to the maximum amplitude, even though the
amplitude of the signal acquired with channel 1 could appear larger at first glance.
Fig. 3: Measurement using the HMO1002.

Basics
1.1.2 Signals and bandwidth
Signal integrity is key to precise and reproducible measurements. Signal integrity

refers to the ability of an oscilloscope to reproduce an electrical signal in its true
original form. Measurements that do not provide signal integrity are essentially useless
because the measured signal might not match the actual signal in either its shape or
characteristics.
This is why bandwidth is one of the most important characteristics for an oscilloscope.
It is only when a signal is not affected by the finite bandwidth of the test instrument that
precise measurements are possible and the signal details can be displayed. However,
in certain situations a test instrument's bandwidth will be reduced intentionally, for
example, to minimize the effect of noise.
By definition, the bandwidth is the frequency at which a sinusoidal signal is attenuated
by 3 dB (about 30 %) as compared with the original amplitude. This frequency
corresponds to the –3 dB point in a lowpass, which have characteristics that are
essentially like those of an oscilloscope.. Fig. 4 shows the frequency response of the
HMO1002. Oscilloscopes are dimensioned for the flattest frequency response possible
within the specified bandwidth, which means that the –3 dB point will lie outside of the
specified bandwidth. This ensures that it is still possible to analyze and measure
signals near to the upper bandwidth limit. The HMO1002 can therefore be used for
measurements over the entire specified bandwidth. As seen in Fig. 4, measurements
above the specified bandwidth are in theory also possible with some restrictions.
However, signal distortion and imprecise measurement results must be expected in
this situation.
Fig. 4: Frequency response of the HMO1002.
Oscilloscopes are frequently used to measure digital pulses. In theory, square-wave

signals have an unlimited spectrum consisting of the fundamental frequency (e.g.
1 MHz) and odd-numbered multiples of the fundamental frequency, called harmonics
(e.g. 3 MHz, 5 MHz, 7 MHz, etc.).
The following rules of thumb are generally accepted for quickly estimating the required
bandwidth (2).
ı To preserve the integrity of digital signals, the bandwidth should be at least five
times the clock frequency, which means the bandwidth permits signal components
up to the 5th harmonic.

Basics
ı The simple bandwidth is sufficient for simple decoding of signals, however.

If the required bandwidth for measuring digital signals must be defined more precisely,
the rise time 𝑇𝑟 of a pulse can be included in the calculation instead of the clock
frequency. In the case of a digital signal, most of the energy is concentrated below a
given frequency. Formula (1) can calculate this frequency, also known in the literature
as cutoff frequency, or knee frequency 𝑓𝑘𝑛𝑒𝑒 . This shows that an electronic circuit with
a flat frequency response up to 𝑓𝑘𝑛𝑒𝑒 permits a digital signal to pass with practically no
distortion. The factor 0.35 is based on the rise time definition for digital signals typically
used today, which looks at the rise time between 10 % and 90 % of the settled final
value for the pulse.
0.35
𝑓𝑘𝑛𝑒𝑒 = (1)
𝑇𝑟
where
𝑇𝑟 Rise time of the pulse
Depending on how much accuracy is desired, 𝑓𝑘𝑛𝑒𝑒 must then be multiplied by a
constant. If an accuracy of 20 % is sufficient, then 𝑓𝑘𝑛𝑒𝑒 can be set to be equal to the
oscilloscope bandwidth, while 𝑓𝑘𝑛𝑒𝑒 must be multiplied by 1.3 for an accuracy of 10 %.
(3) CITATION Joh93 \l 1031
It is also important to remember while performing measurements that the oscilloscope
is not the only source of signal distortion. The probes being used can also be a
possible source. This is why the bandwidth of the probes must be selected with an eye
toward preserving the signal integrity of the signal under test.
The following section discusses this in more detail.
1.1.3 Probes
In a test setup, probes represent the connection between the signal source, i.e. the
DUT, and the oscilloscope. Their primary objective is to transmit the signal to the
oscilloscope in as close to its true form as possible to ensure maximum signal integrity
and measurement accuracy. To meet these requirements, selection of the appropriate
probe to match the measurement task and the hardware in use is essential. This
section provides an overview of the most important probe parameters and
characteristics.
An ideal probe would have an infinite bandwidth that would not place a load on the
circuit under test during the measurement. This would make an unadulterated analysis
of the circuit's behavior possible. However, this is not possible using any hardware
available today. That is why a check should be made before each measurement to
determine whether the expected limitations are still acceptable or whether the
permissible frequency range was exceeded. A reliable assessment is possible based
on the bandwidth and impedance of the probes being used.
Bandwidth
The combination of oscilloscope and probe creates a new system with its own
bandwidth. This can be approximated as shown in (2):

Basics
2 2
1 1 1
= √( ) + ( ) (2)
𝐵𝑠𝑦𝑠𝑡𝑒𝑚 𝐵𝑝𝑟𝑜𝑏𝑒 𝐵𝑜𝑠𝑐𝑖𝑙𝑙𝑜𝑠𝑐𝑜𝑝𝑒
To keep the possible measurement errors at a minimum, the selected system

bandwidth should be larger than the highest frequency present in the signal.
Use the following rule to quickly estimate the required bandwidth for the probe being
used (2) CITATION Roh \l 1031:
ı The bandwidth of the probe should be 1.5 times the bandwidth of the
oscilloscope(valid for Oscilloscopes to about 1 GHz bandwidth with a Gaussian
bandlimiting).
Impedance
In addition to the bandwidth, the probe impedance is another important characteristic
for practical applications. Impedance is closely linked to the load placed on the circuit
under test by the oscilloscope+probe system. As a result, a probe's resistance should
be at least equal to ten times the resistance of the circuit. If it is not, the measured
amplitude could be attenuated, for example. In this case, a significant portion of the
current flowing through the circuit is also passed through the probe.
For this introduction into measuring with oscilloscopes, only passive probes 2 are of any
relevance. Therefore only this type will be described here. The most important
characteristic to remember for passive probes is that the impedance can change
significantly versus the frequency. This effect can primarily be attributed to the various
factors that contribute to loading of the circuit. At low frequencies, the resistive
components are dominant. As the frequency rises, the capacitive and inductive
components increase in significance:
The capacitance of probes, which function as a lowpass filter at high frequencies, can
greatly reduce the input impedance. This results in the loss of information present in
high-frequency signal components, while the rise time and bandwidth of the system are
reduced.
The loop formed from the tip of the probe to its ground wire places an inductive load on
the circuit that results in distortions in the signal, in particular overshoot and
undershoot. To prevent this effect, the probe's ground connection should be kept as
short as possible, as should the physical distance to the device under test. Fig. 5 on
the following page shows two example measurements.
The effect can be significant enough for the measurement using the oscilloscope to
damage a functioning resonant circuit.
2 Probes without any active components, such as amplifiers.

Basics
Fig. 5: Measurements using a probe.
The use of 10:1 probes permits the dynamic of the system and the resistive input
impedance to be increased even further. This type of probe increases the input signal
by a factor of 10. The advantage is that the oscilloscope can now display signals with
ten times the amplitude as compared with measurements using a 1:1 probe. However,
the overall system loses sensitivity, making 1:1 probes preferred over 10:1 probes for
signals with amplitudes in the several millivolt range. Some probes offer selectable
attenuation ratios, including the probe shown in Fig. 6 used for these measurements,
the R&S®HZ154. The key point is that the attenuation ratio of the probe in use must be
known to the oscilloscope to ensure that the amplitudes are displayed correctly.
Fig. 6: R&S®HZ154 probe with 10:1 and 1:1 attenuation ratios.
Passive probes are typically characterized by a low resistive load. For measurements
in the high megahertz range, however, active probes should be used because of the
increasing capacitive load.
The following factors make passive probes suitable for general measurements in a
wide variety of applications:
ı Favorable price
ı Ability to operate without an additional power supply
ı Robust design
Passive probes additionally require an adjustment before a measurement is started.
The adjustment for low frequencies differs from that for high frequencies. The low-
frequency adjustment matches the capacitance of the probe to the input capacitance
on the oscilloscope. For example, if a 10:1 attenuation ratio is selected for the probe,
the probe will have a resistance of 9 MΩ, which in combination with the 1 MΩ input
resistance on the oscilloscope creates a voltage divider. The input capacitance of the
oscilloscope generates a lowpass for which the frequency response can be
compensated by using a highpass with the same cutoff frequency. This is why
impedance matching of the highpass must be possible using an adjustable capacitor.
The impedance matching is performed by manually adjusting the probes. For

Basics
measurements starting at about 50 MHz, an HF adjustment should additionally be

performed.
The R&S®HMO1002 includes a special menu item that launches a wizard for
performing the adjustment. Fig. 7 shows the adjustment of a probe for low frequencies.
A comparison against the image on the right shows that the probe still needs to be set
in order to more closely approximate the ideal square-wave format.
Fig. 7: Adjusting the HZ154 probe on the HMO1002.
1.2 Configuration
Once the appropriate setup has been selected for the measurement task, the
measurement can be started. Fig. 8 shows two possible test setups. In addition to the
items discussed above, the oscilloscope must be configured to optimally meet the
requirements for the measurement. This section provides the background needed to
perform these steps.
Fig. 8 Exercise setups for oscilloscope measurements.

Basics
1.2.1 Vertical resolution and dynamic range
When working with the input signal, the analog-to-digital converter (ADC) is the core
component of every digital oscilloscope. In the case of the HMO1002, the ADC is an 8-
bit converter. The ADC converts the measured signal into 28 = 256 values. The
smallest voltage difference that can be displayed, which also corresponds to the least
significant bit (LSB) on the ADC, is calculated as follows:
∆𝑈𝑖𝑛𝑝𝑢𝑡
𝑈𝑙𝑠𝑏 = (3)
2𝑛
where
∆𝑈𝑖𝑛𝑝𝑢𝑡 Input voltage range
n Bit count for the ADC

The vertical scaling set by the user plays a decisive role. This scaling corresponds to
the entire input voltage range, or dynamic range, for the converter. For example, if an
8-bit converter is used with a vertical resolution of 50 mV/div, the smallest increment
that can be displayed is 2 mV. On the other hand, a vertical scaling of 100 mV/div
doubles the minimum resolution to 4 mV.
Fig. 9 shows these scenarios. The same signal is shown in both the right and the left
images with a vertical resolution of 50 mV and 100 mV, respectively. In the image on
the left, the entire dynamic range of the ADC (blue arrow) is utilized, which results in a
better resolution of the measured signal. Therefore, when using digital oscilloscopes
for measurements, always remember the following:
ı For the greatest possible accuracy, the display of the input signal should utilize the
entire dynamic range of the ADC.
Fig. 9: Vertical resolution at different scalings.
1.2.2 Signal sampling and processing
Not only the resolution of the converter, but also its speed are key factors for many
measurement tasks. The ADC samples the continuous signal at regular intervals and
at defined times. The obtained digitized values are known as samples. The sample

Basics
rate is equal to the number of samples the oscilloscope can take per second. In the
case of the HMO1002, a maximum of 1 Gsample/s is possible for one channel and 500
Msample/s in two-channel mode.
The sample rate must be sufficiently high in order to display the signal correctly. If the
selected rate is too low, aliasing errors will occur and the signal will be displayed
incorrectly. This is known as undersampling. Fig. 10 shows how a low sample rate
affects a 10 kHz input signal.
In this example, the sampling points are linked linearly; oscilloscopes typically use a
sine(𝑥)
interpolation here. The sampling rate has to be at least 2.5 times the maximum
𝑥
bandwidth of the oscilloscope. In summary, a high sample rate results in the following:
ı More precise signal reconstruction
ı Better detection of short-term anomalies (glitches). It should be noted that only the
anomalies are located within the bandwidth of the oscilloscope can be detected.
ı Higher sampling density requires a higher memory requirement.
Fig. 10: Effects of low sample rates.
Bandwidth and sample rate are key characteristics for oscilloscopes, and the highest
possible values should be targeted for both. Even though the two characteristics are
not physically coupled, the correct dimensioning is critical here.
To be able to faithfully reproduce measured signals the double sampling rate, ie 2 ∙
fsignal, max, according to the Nyquist-Shannon theorem, is already sufficient. Due to the
non-ideal band limitation of the oscilloscope the sample rate should correspond in
practice at least 2.5 times the bandwidth of the oscilloscope.
However, it has been shown that square-wave signals, whose transitions are often
very fast and which contain frequency components significantly higher than the Nyquist

Basics
frequency, require several times the bandwidth for reproducible measurements. For
example, the HMO1002 is available with a maximum bandwidth of 100 MHz whereas
the maximum sample rate is 1 Gsample/s.
In this context, it is important to note the following:
ı A high bandwidth can be much less useful if only a low sample rate is available.
With all of the apparent advantages, it begs the question: Why not simply always use
the oscilloscope with the highest sample rate? In addition to the obvious cost factor
represented by the converter – a higher sample rate is obtained by using expensive,
faster ADCs or multiple converters that combine the samples – this question can be
answered by looking at the memory depth.
Memory depth
Once the samples have been taken, the oscilloscope processes the sample values as
defined by its current settings. The result is transferred to the test instrument's high-
speed storage. The memory depth defines how many of these values can be saved
and thus also defines the maximum acquisition period. If a large time range is to be
acquired at the full sample rate, the oscilloscope must possess an appropriately large
memory depth. Typically, the oscilloscope measurement speed is greatly reduced if the
entire storage space is used because of the large amount of processing power
required for large volumes of data. This leads to topic of blind time as described in the
next section.
In summary it can be said that a high sample rate requires not only a fast analog-to-
digital converter, but also sufficient memory depth on the oscilloscope for trouble-free
operation. Both factors drive up the price of an instrument significantly, which is why it
is advisable to be clear about the T&M requirements before purchasing an
oscilloscope.
Update rate and blind time
The concept of an update rate was introduced to provide users with a convenient value
that defines the frequency at which the oscilloscope can take measurements. The
higher the update rate, the more acquisitions the oscilloscope can perform per second.
However, it must be remembered that a digital oscilloscope spends only a fraction of
the time actually acquiring the signal. The rest of the time, the instrument is processing
and storing the incoming data stream. For example, the HMO1002 in combination with
the 8-bit ADC must process 8 Gsample/s of data to achieve the maximum sample rate
(1 Gsample/s). Interpolation of the readings and the user-defined math or analysis
functions additionally delay the next acquisition point. During this time, the test
instrument is "blind," i.e. no new measurements can be started. As a result of this blind
time, errors and deviations in the signal are more difficult to detect and analyze.
Fig. 11 shows the acquisition cycle for a digital oscilloscope. The fixed portion of the
blind time is specific to each instrument. On the other hand, the variable portion is
dependent on the settings that have been defined for the acquisition and processing. In

Basics
this example, the instrument is processing data 99.999 % of the time. (4)
Fig. 11 Acquisition cycle for a digital oscilloscope.
Acquisition modes
Many oscilloscopes offer at least two different acquisition modes, each of which is
intended for different applications.
Realtime mode
Because the analog-to-digital converter has always the same speed, the number of
Samples will be reduced when the measurement is performed at a slow time basis. In
this case, the sampled values are used to reconstruct the signal directly. If a faster
timebase is selected, the acquired points from the ADC are supplemented with
interpolated values.
Equivalent time mode
This mode is used to analyze signals whose frequency is high above the sampling
frequency of the converter. However, this mode requires stable, repetitive signals. An
oscilloscope operating in equivalent time mode takes points from different acquisitions
that were sampled at different points of the periodic signal and combines them into a
single display.

Basics
1.2.3 Triggering basics
On oscilloscopes, the trigger is used among other things to provide a stable display of
repetitive signals. Another important application is the synchronization of the
acquisition to specific points in the signal that are of particular interest. When the
trigger is initiated, the oscilloscope generates a snapshot at that precise moment of the
current signal.
The trigger settings can be used to define the precise conditions under which a trigger
should be initiated. The trigger point is set when all of the defined requirements are
met by the signal at the same time. The oscilloscope has already continuously
acquired data points, which are then used to fill in the pre-trigger portion of the
acquisition. Once triggered, the oscilloscope acquires as many samples as required to
complete the post-trigger portion, at which point the signal can be displayed on the
monitor. Fig. 12 shows a simplified version of a digital trigger. This type of trigger
system works directly with the ADC samples. (5)
Fig. 12: Simplified digital trigger setup.
Most oscilloscopes support, at a minimum, the following trigger conditions:

ı Signal source
ı Trigger type, with various settings
ı Horizontal trigger position
ı Mode
The HMO1002 can use channel 1 or channel 2 as the signal source.
Modern digital oscilloscopes offer many different trigger types; this section will address
only the edge triggers. This type is triggered as soon as the signal exceeds the trigger
threshold (the vertical position of the trigger). The typical setting options include the
threshold height and either rising or falling edge.
By saving the samples before and after the trigger time, the acquisition at various pre-
trigger and post-trigger points can be analyzed later in leisure. The trigger settings can
also change the trigger time by adjusting the horizontal position of the trigger.
Each oscilloscope supports two basic trigger modes. The two modes differ only in how
they respond when the conditions for a trigger event are not met. The following
descriptions assume that the signal does not exceed the trigger threshold.

Basics
Auto mode
In auto mode, the oscilloscope uses fist the selected trigger condition. If the trigger
condition will not be fulfilled, the oscilloscope generates an asynchronous trigger that
displays the signal at random times. The advantage of this mode is that a general
assessment can be made as to whether a signal is present and what amplitude it has.
Normal mode
In normal mode, on the other hand, the oscilloscope does not refresh the monitor until
the trigger conditions have been met again. This mode is preferred if the trigger event
occurs only very infrequently.
Fig. 13 lists several settings for the edge trigger on the HMO1002 and their effects.
The arrows along the edges of the images show the horizontal and vertical position of
the trigger, which is indicated by a red circle.
In image , the trigger system is not yet set correctly. The selected trigger level is too
high, which is why a valid trigger event is not present. This setting will not generate a
stable image. The oscilloscope is apparently in auto mode, as it is displaying the
asynchronously triggered signal. In image , the trigger was set to rising edge with a
trigger level of 0 V. In image , the trigger was changed to falling edge, but the
selected horizontal offset (–10 µs in this example) is such that at first glance, it appears
to be the same as image . The final image shows that the display can also combine
rising edge and falling edge triggers. This is useful for assessing the symmetry of a
signal, for example.
Fig. 13: Effects of various trigger settings.

Preparing for the measurement exercises
2 Preparing for the measurement exercises

This chapter begins the practical portion of the educational note. The following
chapters deepen the reader's understanding with typical measurement tasks used in
the analysis and verification of electronic circuitry.
Before starting with the actual measurements, however, a few points should be
mentioned about using oscilloscopes.
When using passive probes, always measure against ground!
Even though an oscilloscope measures voltages like a multimeter, it cannot be used in
the same way in the test setup. The ground clip for a probe must always be connected
to ground to prevent a short circuit of the circuit nodes. Fig. 14 shows what happens
when a measurement is performed incorrectly. The red arrow corresponds to the tip of
the probe and the gray arrow to the ground clip. As seen in the image on the right, the
circuit is set completely out of operation. This setup will not produce any useful
measurements! In a worst-case scenario, the short circuit can cause serious damage.
Specialized differential probes can be used for differential measurements.
Fig. 14: Correct use of an oscilloscope for measurements.
Passive probes require adjustment, and the attenuation ratio must be known in
the oscilloscope!
As described in section 1.1.3, all probes must be adjusted before being used in the
measurements. On the HMO1002, this is done by pressing the Setup button in the
General grouping. In the submenu, use PROBE ADJUST to open the adjustment
wizard. Once a probe is connected as described on the monitor, the appropriate
channel must be selected. Fig. 15 shows an LF adjustment on channel 1. To perform
the HF adjustment, select NEXT STEP.
► Perform the adjustment on both channels.

Preparing for the measurement exercises
Fig. 15: Performing the probe adjustment.
Once the adjustments have been successfully completed, a check must be made to
ensure that the correct attenuation ratio for the probes is known in the oscilloscope.
First check that the switch is set to 10:1 (x10) on both probes. In the grouping for the
vertical system, use the MENU key and select PROBE on the monitor (page 2) to set
the attenuation ratio. The channel can be changed by pressing the CH1 / CH2 key.
After every preset, the duty cycle must be set again!
Note: higher class Oscilloscopes, such as R&S® RTM200 or R&S® RTO offer with
suitable probes an automatic recognition of the division ratio.
Almost every modern oscilloscope offers an autoset function that automatically
performs all necessary settings on the instrument to optimally display the signal. While
this function can be very convenient for daily measurement tasks, to increase the
educational value of these exercises it is better not to use it here. Once you are
sufficiently comfortable working with oscilloscopes, you can use autoset to get an initial
overview of the measured signal. The HMO1002 offers an education mode that
deactivates the autoset function along with all automated measurements. If necessary
this mode can be password-protected.
► Use SETUP → EDUCATION MODE (page 3) to enter education mode.
Perform all exercises in education mode!
𝑆𝐴𝑉𝐸
Press the button and select DEVICE SETTINGS → DEFAULT SETT. to reset
𝑅𝐸𝐶𝐴𝐿𝐿
the oscilloscope to the default settings.
By performing a Preset, the instrument should be reset to the default settings
before every exercise!
Throughout the exercises, you will find thought-provoking questions that will lead to a
better understanding of the exercise. The questions are in italics and indicated by the
symbol . Most of the questions can also be answered beforehand in order to prepare
for the exercises.

Basic measurements
3 Basic measurements
In spite of all the automation of measurements, manual setup and estimation of
measurement results are still an important part of an engineer's everyday life. This
chapter provides a practical introduction into the operation of a modern oscilloscope
and the completion of basic measurement and display procedures.
3.1 Exercise setup

The setup in Fig. 16 is provided as a general overview and will be worked through
step-by-step in the exercise.
The training board in Appendix A.1 will not be used until later in the exercise.
Fig. 16: Test setup for manual measurements.

Basic measurements
3.2 Exercise
► Set the oscilloscope to the default state (PRESET).
► Set the duty cycle for channel 1 to 1:1 and for channel 2 to 10:1; see also chapter 2.
The HMO1002 has both an integrated function generator and a test pattern generator.
The function generator whose output signal can be tapped on BNC jack AUX OUT is
used for the initial measurements.
► Connect a BNC cable from the function generator to the input for channel 1.
To switch on the generator, press the UTIL button in the VERTICAL grouping and then
select FUNCTION GEN. on the monitor.
► Switch on the function generator and then use the key to exit the menu.
The function generator generates a 1 kHz sine-wave signal with a peak-to-peak
voltage of 500 mV.
The crosshair in the center of the screen, in combination with the arrows at the left and
upper edges of the monitor, indicates the current trigger position.
► Set the horizontal and vertical scaling and the trigger threshold to generate a stable
image similar to Fig. 17 on the oscilloscope.
The display of the second channel can be removed by pressing the CH2 key twice.
Fig. 17: Measuring the period and the peak-to-peak voltage of a sine-wave signal.
► Read the frequency of the sine-wave signal by counting off the grid squares
multiplied by the horizontal scaling. (Do this even if you already know it!)
By varying the vertical offset, you can obtain a display as shown in Fig. 17 , which
makes it possible to read the amplitude of the signal more precisely.
► Determine the peak-to-peak voltage of the sine-wave signal and compare your
results against the settings in the function generator.
The method used above does not provide exact measurement results. While a visual
analysis is suitable for quick estimations, cursor measurements deliver significantly
more accurate results.
After it is reset to its default settings, the oscilloscope will automatically use the edge
trigger. As you have seen, when working with sine-wave signals it is useful to trigger
on the falling or rising edge. This type of trigger is suitable for square-wave signals as
well.

Basic measurements
► Set the function generator to a pulse signal at a frequency of 10 kHz and leave the
other parameters unchanged. Use the KEYPAD button to set the frequency.
This signal is triggered correctly with the current settings, as well.
► Adjust the horizontal scaling for optimal measurement of one pulse width.
In the CURSOR/MENU grouping, locate the CURSOR MEASURE button.
► Open the cursor menu and select the time measurement.
You can show shift the displayed markers horizontally using the SELECT rotary knob.
𝐶𝑂𝐴𝑅𝑆𝐸
The key must be pressed for fine adjustments. Pressing the SELECT rotary
𝐹𝐼𝑁𝐸
knob switches between active cursors.
► Measure the pulse width; see Fig. 18 for an example. The pulse width is measured
at 50 % of the amplitude in the steady state.
Fig. 18: Cursor measurement of a pulse width.
► Measure the duty cycle for the signal.

Fig. 18 shows the finite rise time for the pulse. Depending on the bus specifications,
the 10 % to 90 % definition (for example TTL) or the 20 % to 80 % definition (for fast
buses based on LVDS) is used to measure the rise time. In this definition, the rise time
is the time required for the amplitude to rise from 20 % to 80 % of the final settled
value.
► Set the oscilloscope so that the rise time can be properly measured.
Fig. 19 provides an example of a correct HMO1002 display configuration for measuring
the rise time 𝑡𝐴 . The important thing to note is that the steady state is assumed for 0 %
and 100 %.

Basic measurements
Fig. 19: Measuring the rise time of a pulse.
What is the minimum bandwidth an oscilloscope must have in order to

measure the signal from Fig. 19 with 10 % accuracy? Use formula (1) to
calculate.
► Measure the rise time for the pulse and calculate the required oscilloscope
bandwidth.
The MEASURE TYPE menu also offers a number of automated measurements.
► Select Rise Time 80% and set the cursor so that the rise and fall times can be
measured simultaneously; see Fig. 20.
Fig. 20: Automated cursor measurement.
► Compare the results.

Basic measurements
The automated measurements are suitable for quick analyses. As you have seen here,
however, the user has very little influence on these measurements. It must therefore
always be remembered for these types of measurements that even if the measurement
is automated, the plausibility of the results must be manually checked at the very least!
It can sometimes be useful to measure two signals simultaneously. The HMO1002 has
two independent inputs for this purpose.
► As shown in Fig. 16, connect channel 2 to the output S0. Always remember to
connect the probe ground wire.
Press the CH2 key to select channel 2. Repeated pressing of the CH1 or CH2 key
displays or hides the respective channel.
► Display channel 2 and hide channel 1.
The signal under test is present on channel 2. The oscilloscope must therefore know to
apply the trigger to this channel.
► Under the TRIGGER grouping, use the SOURCE button to select CHANNEL 2.
The test pattern generator is used as the signal source for channel 2. This is designed
for higher frequencies than the signal generator on the HMO1002. As a result, the
signal edges are significantly steeper.
Like the signal generator, the test pattern generator is selected using the UTIL button.
► Switch on the PATTERN GENERATOR and select SQUARE WAVE. Accept the
remaining settings without modification.
► Perform another rise time measurement on this signal and calculate the required
oscilloscope bandwidth for 10 % accuracy.
Is the HMO1002 reliable enough to perform precise time measurements on
this signal?
Next, the effect of smaller bandwidths on the measured signal will be explored.
► Set the test pattern generator to the highest possible frequency and zoom in on a
falling edge via the scaling function. (Set the trigger to falling edge.)
Press the MENU key and reduce the channel bandwidth to 20 MHz.
► Observe how the signal display changes.
What advantages might bandwidth limitation have for measurements?
What is causing the ripple in the unfiltered signal (see Fig. 21)?
► Switch off the bandwidth limiting.

Basic measurements
Fig. 21: Comparing measurements with full bandwidth and limited bandwidth.
► Turn on both channels.

► Set the following parameters for the pulse and square-wave signal sequence on the
signal generator and test pattern generator:
FREQUENCY 10 kHz
DUTY CYCLE 50 %
Display both channel 1 and channel 2 on the monitor; see Fig. 22.
Many signals possess both DC and AC components. Sometimes only the AC
components are of interest. In this case, it makes sense to use AC coupling. When AC
coupling is being used, an upstream 2 Hz input filter is used to suppress the DC
components.
What is the expected result when the DC is suppressed for these signals
(Fig. 22)?
► Press the MENU key and use COUPLING to select the AC option for both channels.
Check the result against your expectations.
Fig. 22: Displaying both channels simultaneously with DC coupling.
DC coupling is more commonly used for measurements.

► Select DC coupling to make all signal components visible again.
The final step in this exercise presents a new display mode, the XY display.

Basic measurements
As you learned in section 1.1.1, an oscilloscope displays a variable as the function of

another variable. The voltage versus time display is most commonly used, but in some
cases it can be very useful to display both of the oscilloscope's independent channels
as X and Y axis. This makes it possible to display diode characteristics, for example.
► Connect the training board from Appendix 50A.1 to the USB port as shown in Fig.
16.
The training board must be configured so that a sine-wave signal can be tapped at the
ANA output.
► Use the two keys to switch to state as defined in Table 2.
► Use the probe connected to channel 2 to tap into the signal at the ANA output.
► Perform a cursor measurement to determine the frequency and amplitude of the
sine-wave signal being measured on channel 2.
XY mode is not only very practical for measuring component characteristics but can
also be used to determine the phase difference between two signals.
You have already learned about the integrated signal generator on the oscilloscope.
► Configure the signal generator so that channel 1 has a signal that approximates the
sine-wave signal just measured on channel 2 as closely as possible.
An oval figure is displayed after switching to XY display mode. The phase angle of the
two signals can be identified based on the shape and position of the displayed figure;
see Fig. 23.
Fig. 23: Display of frequency ratio 1:1 in XY mode.
On the HMO1002, use the UTIL key and select XY to change to XY mode.
► What is the phase angle for the signals on your monitor?
► Change the frequency on the signal generator in small increments. What do you see
in the standard display and in XY mode?
The images generated in XY mode are called Lissajous figures.
► Set frequency ratio 3:1 and watch the resulting changes.

Documentation and storage
4 Documentation and storage

This chapter provides a practical introduction into the documentation of oscilloscope
measurements. Especially when sharing test instruments, as is typically the case in a
university environment, it can be practical to save all settings and measurement data to
a personal storage medium for later use.
You should have a USB flash drive handy to perform this exercise.
The HMO1002 can save different types of information in order to document
measurements or save current settings:
ı Device setup
Device setup for later import. Data can be stored locally or externally.
ı References
Data records consisting of the device setup and the ADC data. Data can be stored
locally or externally.
ı Traces
Measurement results consisting of only the ADC data and which can be stored
only externally.
ı Screenshots
Image files showing what is displayed on the monitor at a given point in time.
4.1 Exercise setup

The setup for this exercise (see Fig. 24) is identical to the exercise setup in section 3.1.
Fig. 24: Test setup for documentation and storage.

4.2 Exercise
Storing a reference signal:
► Set the oscilloscope to the default state (PRESET). Don't forget to set the correct
duty cycle!
► Configure the test pattern generator so that a 100 kHz square-wave signal is
generated with a duty cycle of 50 %.
► Set several periods of this signal on the monitor with channel 2.
In practice, a generated signal – and in particular its edges – might not meet the
requirements for a product. One possible correction might be to use different filters.
References are a convenient way to compare the signals acquired using different
filters.
The menu for references is opened using the REF button in the VERTICAL subgroup.
► Open the reference signal menu and select RE1.
► Use SAVE to save the signal and the following parameter configuration:
TRACE CH2
STORAGE INTERNAL
Go up one level in the REFERENCES menu and select DISPLAY to make the
reference signal visible.
The display should now look something like Fig. 25. The white signal is the saved
reference.
Fig. 25: Saved reference signal.
The oscilloscope's integrated lowpass filter is useful for simulating a filter being
switched out.
The cutoff frequency for the filter can be set based on the current sample frequency.
To make the cutoff frequency as low as possible, the oscilloscope sample speed must
be reduced.

► In the HORIZONTAL grouping, press the ACQUIRE button and select the option
RECORD MODE → MAX. WFM. RATE.
This setting will reduce the sample rate to obtain the maximum trigger repetition rate.
► In the ACQUIRE menu, select the option ARITHMETIC → FILTER.
Use the SELECT rotary knob to set the cutoff frequency within the range defined by
the sample frequency.
The current display (see Fig. 26) can now be used to visually compare the two signals.
► Experiment with the settings to find out at which harmonics of the fundamental
frequency the square-wave signal is displayed satisfactorily.
► Use ACQUIRE to return the acquisition options to the default:
ARITHMETIC REFRESH
RECORD MODE AUTOMATIC
Fig. 26: Comparing a signal against the reference.
Saving a trace for external analysis:

For many applications, an analysis on the oscilloscope monitor is not sufficient. The
data must often be analyzed and processed in more detail on a computer. This is why
it is possible to load the values acquired via the ADC directly onto a USB flash drive.
► Connect the USB stick to the front jack.
► Turn off the display of the reference signal by tapping the REF key twice on the
GUI.
► Configure the signal generator so that the following signal is generated:
FUNCTION RAMP
FREQUENCY 10 kHz
AMPLITUDE 500 mV (Vpp)
► Display the signal on channel 1.

𝑆𝐴𝑉𝐸 𝐹𝐼𝐿𝐸
The button opens a menu that permits configuration of the button.
𝑅𝐸𝐶𝐴𝐿𝐿 𝑃𝑅𝐼𝑁𝑇
► Under TRACES, accept the settings from Fig. 27:

STORAGE FRONT USB
TRACE CH1
FORMAT CSV
Fig. 27: Saving an acquired signal.
Before saving the signal, the acquisition should be stopped so that the maximum
number of values is used.
𝑅𝑈𝑁
► Use the button to stop the acquisition.
𝑆𝑇𝑂𝑃
► Return to the main menu and then under the option KEY, select TRACES.
𝐹𝐼𝐿𝐸
The button is now configured so that when it is pressed, the current ADC values
𝑃𝑅𝐼𝑁𝑇
are automatically saved to the USB flash drive.
𝐹𝐼𝐿𝐸
► Use the button to save the signal trace.
The ADC values are now available in an Excel-readable .csv format on your USB stick.
If you have a computer available to perform the assessment, you can open the file in
Excel and generate a chart using the data as shown in Fig. 28.

Fig. 28: Importing the data into Excel.
Saving screenshot:
Even though screenshots cannot be loaded back into the instruments like the other
formats described above, they are still a very good format for documenting
measurements.
𝐹𝐼𝐿𝐸
The easiest method is to configure the button so that it saves a screenshot to the
USB stick. The behavior of the button can be configured in the KEY submenu of the
𝑆𝐴𝑉𝐸
button.
𝑅𝐸𝐶𝐴𝐿𝐿
𝐹𝐼𝐿𝐸
► Configure the button as described and save a screenshot to the USB flash
drive, similar to the example in Fig. 27.

Advanced trigger settings
5 Advanced trigger settings

The objective of this chapter is to build on the fundamentals in section 1.2.3 and to
discuss advanced trigger system applications. The exercise shows the correct method
to select and configure appropriate triggers for more complex measurement tasks.
5.1 Exercise setup

For the exercise setup, the internal signal generator of the oscilloscope is connected to
channel 1 and the training board from Appendix A.1 is connected to channel 2 and
supplied with power via the USB port. Fig. 29 shows this setup in its entirety. The
probe connected to channel 2 is first connected to the UART/LIN output on the circuit
board and then later during the exercise to the SIGNAL output.
Fig. 29: Test setup for advanced trigger settings.

5.2 Exercise
duty cycle!
You already learned about the simplest and most frequently used trigger, and you have
used it in the exercises in section 1.2.3. The additional setting options for the edge
trigger are briefly discussed here before the other trigger types are introduced.
► Configure the signal generator so that the following signal is generated:
FUNCTION SINUS
FREQUENCY 1 kHz
AMPLITUDE 500 mV
OFFSET 400 mV
► Display the signal on the monitor.
Triggerfilter:
► Use the FILTER button to open the setup menu for the edge trigger and then select
option AC.
The display should resemble that in Fig. 30. In this mode, the DC component can be
changed at will. The AC filtering ensures that the threshold value for the trigger
remains constant and the signal appears to be triggered correctly. In addition, in auto
mode the threshold value is limited within the signal automatically, which results in a
stable display of the signal even though the trigger level actually does not appear to be
set correctly as shown in Fig. 30. In normal mode, the trigger level can be shifted
above the peak values for the signal.
Fig. 30: Triggering with an AC filter.
► Set the AUTO LEVEL option.

As shown in Fig. 30, it is also possible to add in a lowpass that filters the trigger signal
with an upper cutoff frequency of 5 kHz. The measured signal is not affected by this.
In cases of strong noise, the edge trigger can interpret signal transitions that are
generated by noise components as actual signal edges. To prevent this, the noise

suppression can be switched on, in which case a 100 MHz lowpass filter is inserted
before the trigger signal.
Triggering of data bursts:
► Hide the display of channel 1 and change the training board state to as defined in
Table 2 in Appendix A.1.
The board will generate a UART signal at 115.2 kbaud.
► Use the probe connected to channel 2 to tap into the output signal at the UART/LIN
output.
► Set the oscilloscope so that you can clearly identify the individual bit lengths of a
burst in the bus signal; see also Fig. 31.
Fig. 31: Display of a bus signal with random trigger points.
Although the individual bit lengths are easily recognized in the above screenshot, this
type of display cannot be used to decode the information contained in the
transmission. This is because the oscilloscope triggers on random edges within the
burst. You could either press the SINGLE key in the TRIGGER grouping to initiate a
single acquisition and then use the oscilloscope memory for analysis or you could set a
hold-off time.
The hold-off setting permits the trigger to initiate only after a defined time period. This
ensures that the oscilloscope always triggers on the first falling edge (the start bit) of
the entire burst. In the example of the bus transmission, a time period should be
defined that lies between the length of a burst and the timespan between two bursts.
► Set the horizontal scaling to permit you to estimate the length of a burst and the
timespan between the bursts.
Use the TYPE key to set the trigger type and the hold-off time.
► Set the hold-off value to be a time lying between your two estimated values.
The bus transmission is now displayed with the correct triggering and you should also
be able to see the differences between individual bursts in the form of alternating bits.
The transmission acquired with a hold-off time is shown in Fig. 32.
► Turn off the hold-off time.

Fig. 32: Display of the bus signal with hold-off triggering.
Another trigger form that can now be introduced is the pulse trigger.
This trigger is especially suited to square-wave signals. The many possibilities for
configuring this trigger make it possible to trigger on specific ranges within a
transmission.
The training board can simulate several bus standards as well as different types of
signal errors.
Complex digital circuits are prone to glitches. Glitches cause momentary false
interpretation in logic circuits and a temporary distortion of a Boolean function. They
arise because the signal transient times in the individual logic gates are never
completely equal or by crosstalk. ► Switch the board to state as shown in Table 2 in
Appendix A.1 and use the probe to tap into the signal at the SIGNAL output.
► Use the edge trigger to set the oscilloscope so that several pulses are displayed.
The glitch cannot be detected with these settings even though it appears 100 times per
second. If a glitch is suspected in a signal, the sample rate should be reduced in order
to achieve the highest possible rate of trigger events. This reduces the dead time3
between the measurements and increases the odds of acquiring even rare signal
errors. As described in section 4.2, the HMO1002 offers MAX. WFM. RATE mode.
► Switch to this mode for the maximum signal repetition rate.
The signal errors cannot be detected with the naked eye because of their very short
duration, even with this setting. The HMO1002 offers the option of continuing to display
signals on the monitor for a defined time after the trigger event. In this case, the display
is not updated with the latest acquisition after every trigger event. Instead, a static
image consisting of many acquisitions is displayed.
𝐼𝑁𝑇𝐸𝑁𝑆
This mode is called PERSISTENCE and can be called using the button.
𝑃𝐸𝑅𝑆𝐼𝑆𝑇
3 See section 1.2.2.

► Make the following settings under SETTINGS:

MANUAL INFINITE (maximum value)
BACKGROUND ON
The background option continues to display the existing lines on the monitor for an
unlimited length of time.
To better detect measured glitches, the display intensity should be increased by using
the SELECT rotary knob.
► Set the following on the oscilloscope:
INTENSITY 100 %
This setting makes it possible to detect short pulses occurring at irregular intervals. In
Fig. 33, an acquired glitch can be seen within each regular pulse.
Fig. 33: Pulse packet with a glitch.
This makes it possible to identify the shape of a glitch. With this information, the pulse
trigger can be configured so that it reliably triggers on the transmission error.
► Make a note of the pulse width of a glitch at the height of the trigger threshold.
► Return all PERSISTENCE settings to their original values.
► Make the following settings for the trigger:
TYPE PULSE
FILTER POLARITY POSITIVE
COMPARISON ti < t
TIME t Width of the glitch < t < pulse width
The trigger will now search for a pulse that has a duration shorter than the specified
timespan. Because only the searched glitch matches this condition, the oscilloscope
reliably triggers on the interference, as seen in Fig. 34.

Fig. 34: Triggering on a glitch using the pulse trigger.
In the case of digital signals, runts can occur in addition to glitches. These are normally
shaped pulses that do not have the necessary amplitude. Runts can cause logical 1
not to be recognized correctly, leading to incorrect processing of a data message.
Because the signal errors occur only rarely, a maximum update rate should be used
once more.
► Switch the board to state as shown in Table 2 in Appendix A.1.
► Repeat the glitch analysis steps in order to get an idea of the error properties.
After you have an idea of the shape of the faulty pulse, the trigger must be set so that
the oscilloscope will reliably trigger on the runts.
Some oscilloscopes offer a special runt trigger for this situation, although this is not
offered by the HMO1002. The properties of runts make the procedure used for
triggering on glitches ineffective for runts. Runt triggers analyze the height of a pulse in
order to correctly initiate the trigger.
The following procedure can be used for the pulse trigger in this situation: If the trigger
threshold is set high enough, i.e. over the maximum amplitude of a runt pulse and
under the amplitude of the other pulses, then an unusually long time will pass without a
pulse. The trigger system evaluates this time period as a segment with negative
polarity.
► Turn off the PERSISTENCE settings and configure the pulse trigger so that a stable
image similar to that in Fig. 35 is generated.
Fig. 35: Triggering a runt pulse.

Signal analysis using FFT
6 Signal analysis using FFT

Even if it initially seems unusual, many digital oscilloscopes offer a simple form of
spectrum analysis that uses Fast Fourier transformations. This chapter provides a
practical introduction into the analysis of signals in the frequency domain using an
oscilloscope.
6.1 Exercise setup

The exercise setup consists of the oscilloscope and the training board from Appendix
A.1, which is supplied with power via the USB port. Fig. 36 shows this setup in its
entirety. The oscilloscope's integrated signal generator is first connected to channel 1.
A probe is then connected that will measure the signal that is output at the
10_MHZ_CLK output. Channel 2 on the oscilloscope is connected to the MICP output
of the circuit board via a probe.
Fig. 36: Test setup for signal analysis using FFT.

6.2 Exercise
duty cycle!
Before beginning the exercise, configure the oscilloscope to use the maximum sample
rate.
► Switch the oscilloscope to MAX. SA. RATE mode.
► Press the FFT button under the ANALYZE grouping.
The screen is split into two panes; see Fig. 37. The upper pane ( ) displays the
previously defined voltage-time trace for the measured signal and the settings for the
horizontal system.
The zoom and position information is displayed in between the two panes ( ). Only the
signal segment that is displayed on the monitor and bound by the two vertical white
lines is used for the FFT.
What does the frequency spectrum for a sine-wave signal look like if its
maximum amplitude lies far above the displayed range as a result of the
vertical system being set incorrectly?
The lower pane ( ) shows the result of the FFT analysis and the associated settings:
Span shows the size of the currently displayed frequency range. The span, timebase
and selected segment are directly linked to one another. As the selection for the
timebase and the range in the time domain displayed between the two vertical lines
increases, so too decreases the frequency band that can be set.
Center defines the frequency at the center of the segment displayed on the monitor.
The minimum step size ∆𝑓 can be set indirectly via the number of points.
Fig. 37: Setup of FFT mode.

Press the TIME/DIV rotary knob to switch between the panes. The currently active
pane (time domain, selected signal segment for the FFT or frequency domain) is boxed
in white. The rotary knobs are assigned different tasks depending on the currently
KNOB
MODE VOLTS/DIV + Offset TIME/DIV + Offset
Voltage range (total)
Time domain Timebase (s/div)+Position
of the signal segment
Voltage range (total) Width of the signal
Signal segment
of the signal segment segment for the FFT (ms)
Voltage scaling (V/div)
Frequency domain Frequency band (Hz)
in the spectral display
active pane:
Table 1: Controls in FFT mode
A sine-wave signal is initially measured as an output signal from the signal generator.
► Set the following on the function generator:
FUNCTION Sinusoid
FREQUENCY 50 kHz
AMPLITUDE 350 mV (Vpp)
► Set the timebase for the oscilloscope to 500 µs and select a maximum signal
segment for the FFT.
► Select the minimum frequency band for these settings and verify that the spectrum
of the sinusoidal signal is displayed correctly.
Press the FFT button to open the menu again.
► Display the result in dBV; see Fig. 38.
The HMO1002 offers four different window functions.
► Explain why the window functions are needed, and explain the differences between
the various functions. (For detailed information please see the HMO1002 manual)
► Compare how each of the window functions affects the spectrum.

Fig. 38: Measuring a sine-wave signal using the rectangle window.
Clocksignal:
The training board provides a 10 MHz clock in all operating modes. Use a probe to tap
into this clock pulse.
► Accept the following settings:
TIME BASE 1 µs
VOLT RANGE 500mV
SPAN 100 MHz
POINTS 131072
Fig. 39: FFT analysis of a square-wave signal.
As can be assumed for a square-wave signal, only odd harmonics of the fundamental
frequency are present.
What is the rule that says that the amplitudes decrease for a square-wave
signal?
As seen in Fig. 39, FFT mode also supports cursor measurements.
► Measure the amplitudes of the harmonics and verify your assumptions.

The signal has a DC component that can be filtered.

How does the DC component affect the FFT?
MIC-Signal:
The training board is equipped with a microphone. This hardware can be used to make
acoustical signals visible on the oscilloscope and available for analysis using the FFT
function.
The output signal from the microphone is differential. Two outputs, MICP and MICN,
are therefore available. In the next chapter, you will learn how to measure these
signals differentially using the oscilloscope. For this exercise, it is sufficient to tap into
the MICP signal.
► Switch the board to state as shown in Table 2 in Appendix A.1.
The image at the left of Fig. 40 shows the measurement of a 1 kHz sine-wave signal
generated by a smartphone. The screenshot in the right half of the figure was acquired
during playback of an .mp3 file. In this image, the attenuation of the higher frequencies
by the format is visible.
If the source is located directly at the microphone, the volume can be set very low.
Fig. 40: Measuring different signals using the training board microphone.
The optimum settings depend on the signal source. For the measurements in Fig. 40,
the following configuration was used:
TIME BASE 10 ms
WINDOW WIDTH 78.64 ms
SPAN 50 kHz
CENTER 5 kHz
► Using an appropriate device (such as a smartphone), generate a variety of signals

and analyze them using the oscilloscope's FFT function.

Analysis of protocol-based bus signals
7 Analysis of protocol-based bus signals

Signal buses play an important role in electronic systems, ensuring error-free and rapid
communication between all system components. Modern oscilloscopes are able to
decode bus signals. Therefore they are perfectly suited for the important task of
screening all bus functions. This chapter provides a look into the various bus systems
and analysis methods using an oscilloscope.
IMPORTANT NOTE: A portion of this exercise requires the H0012/HV112 option.
7.1 Test setup

For the test setup, the training board from Appendix A.1 is connected to both channels
and supplied with power via the USB port. Fig. 41 shows this setup in its entirety. The
probe connected to channel 1 is first connected to the UART/LIN output on the circuit
board and then later during the exercise to the CAN_H output. The signal is applied to
channel 2 from the CAN_L output.
Fig. 41: Test setup for analysis of bus signals.

7.2 Exercise
duty cycle!
UART-Bus:
As an example for a simple bus transmission, let us take a closer look at the UART
signal from section 5.2. The following values are defined for the transmission:
THRESHOLD 1.65V
BIT RATE 115.2Kbps
STOP BITS 1
DATA BITS 8
PARITY None
BIT ORDER LSB First
POLARITY Idle High
What defines the THRESHOLD value?

► Switch the training board to state as shown in Table 2 in Appendix A.1.
► Use a pulse trigger as described in section 5.2 to generate a stable display of the
channel 1 signal.
► Use a marker measurement to check the bit rate.
In Fig. 42, a data byte is marked within a UART transmission. Note that the
transmission begins with the least significant bit (LSB) and ends with the most
significant bit (MSB). A start bit (logical 0) is inserted before and a stop bit (logical 1)
after every transmitted byte. The bytes to be transmitted are arranged sequentially
following these rules. The resulting byte sequence is combined into packets. Individual
packets are separated by idle time. The Idle High setting is interpreted by the bus as
logical 1 during this time.
Fig. 42: Setup of a data byte within a UART transmission.

The marked byte in Fig. 42 transmits the value: 0101 0100b.

In this example, an entire packet consists of a 12-byte ASCII string.
► Read the first four bytes of the string as ASCII characters.
You can likely now explain why several of the middle bits in the transmission
continually alternate. You will soon be able to decode the entire data message using
the automated tools on the HMO1002.
Before moving on to the measurement of other bus systems, it is important to
understand a peculiarity of UART transmissions:
A UART transmission is started asynchronously. This means that the transmitter can
start transmitting the data at any time. In addition, no clock signal is needed because
the accuracy of the local oscillator synchronized to the frame is sufficient for the short
packets within the transmission.
One of the most widely used UART buses is the RS232 interface.
During the manual analysis of the UART transmission, you probably noticed how time
consuming and error prone the manual analysis of a bus transmission can be. The
HMO1002 offers automated analysis programs for a variety of buses. The oscilloscope
must first be used to decode the entire content of the UART transmission.
Use the BUS button under the VERTICAL grouping to turn on the bus analysis.
► Set the oscilloscope to BUS mode and open the settings using the MENU key.
► Select UART as the BUS TYPE and set the parameters listed at the start of the
chapter under CONFIGURATION.
To get a display as shown in Fig. 43, the vertical scaling must be adjusted and the data
decoded as ASCII characters.
► Set the scaling to 500 mV/div and then set DISPLAY SETUP to ASCII to display the
transmission in plain text.
Fig. 43: Automated analysis of a UART transmission.
CAN-Bus decoding and triggering:

The CAN bus standard was developed in large part for use in the automotive arena.
For this application, immunity to noise is very important. Therefore, systems like the
RS232 interface are not possible here.
In the CAN bus, differential signals are used to suppress common-mode disturbances.
Even if the passive probes are designed only for measurements relative to the ground
potential, they can still be used to measure differential signals. Basically, when a
differential signal is received, the negative component is subtracted from the positive
component. This task can be undertaken using the oscilloscope test setup shown in
Fig. 41.
► Use channel 1 to measure the CAN_H signal and channel 2 to measure CAN_L.
Superimpose the two signal components on the oscilloscope display over the length of
the packet.
Fig. 44: Measuring differential signals.
► Press the MATH key under the VERTICAL grouping on the edge of the monitor and
select SUB instead of ADD in the menu.
With these settings, the signal measured with channel 2 is subtracted from channel 1
and the actual bit sequence is displayed as a red signal; see Fig. 44.
What other advantages of differential transmission can be seen in Fig. 44?
► Calculate the bit rate for the transmission.
CAN bus signals also do not require a separate clock signal. Multiple nodes are
connected to the bus simultaneously. A wired AND connection makes it possible for
these nodes to detect conflicts and respond appropriately.
You can then analyze the previously analyzed CAN bus signals similar to the UART
transmission using the HMO1002.
► Set up an automated CAN bus measurement for the current signal on the
oscilloscope. Use your previously calculated bit rate for the configuration.
The current trigger settings will not permit a stable display of the CAN signal. However,
by using the automated bus measurements, a new trigger type is available:

► Under TYPE, select the option SERIAL BUS.

The FILTER key can be used to set the various trigger conditions.
► Select START OF FRAME.
The various segments of a CAN transmission are now visible on the oscilloscope
monitor; see Fig. 45.
The structure of a CAN frame is briefly described here based on Fig. 45.
A single, dominant bit indicates the start of a frame.
This is followed by the identifier (dID), which displays the content of the data message.
The identifier does not provide the destination; instead the receivers decide whether
the data message is relevant for them.
The identifier is followed by the control field, which specifies the number of bytes in the
current frame. In the example, the receiver is expecting two bytes of information that
the oscilloscope has identified as data.
Finally, a CRC code is sent for error detection. (6) CITATION Rob91 \l 1031
Fig. 45: Automated analysis of a CAN bus transmission.

During the analysis of a bus transmission, faulty data packets are of particular interest.
The manual analysis of all received transmissions is not practicable in this case. The
HMO1002 offers special trigger settings for this purpose that permit reliable and rapid
detection of various types of errors.
► Set the oscilloscope up with the optimal trigger and acquisition mode to detect rare
events with the highest level of probability.
► Under FILTER, select the following for the current trigger type:
ERROR CRC
If you shift the horizontal trigger position slightly, you will get a display as shown in Fig.
46. With these settings, the oscilloscope reliably detects the faulty CRC sequence
received every three seconds.
Fig. 46: Triggering on a CRC error.

Reference
8 Reference
[1] 1. Rohde & Schwarz GmbH & Co. KG. R&S®RTO Digital Oscilloscope - User
Manual. [Manual] München : s.n., 2015.
[2] 2. —. Oscilloscope Fundamentals - Primer. Columbia : s.n.
[3] 3. Johnson, Dr. Howard W. and Graham, Dr. Martin. High-speed Digital Design
– A Handbook of Black Magic. s.l. : Pearson Education, 1993.
[4] 4. Rohde & Schwarz GmbH & Co. KG. The Impact of Digital Oscilloscope Blind
Time on Your Measurements. München : Rohde & Schwarz GmbH & Co. KG,
2011.
[5] 5. —. Benefits of the R&S®RTO Oscilloscope's Digital Trigger. 2012.
[6] 6. Robert Bosch GmbH. CAN Specification Version 2.0. Stuttgart : s.n., 1991.

Appendix
A.1 Appendix 1 The training board
Fig. 47 shows the training board used in sections 3.2, 5.2, 6.2 and 7.2. The items used
in those sections are boxed in red and the used outputs (as well as the microphone
input) are identified on the board. To acquire the "Demo Board Time Domain
Measurements" (Service Part No. PW0002.9763.00), please contact the local Rohde &
Schwarz sales representative or service center.
Fig. 47: The training board.

Table 2 lists the various modes for the board. The two keys can be used to switch
between the modes. The LEDs indicate the current operating state.
Table 2: The different training board modes

Rohde & Schwarz Regional contact
The Rohde & Schwarz electronics group offers Europe, Africa, Middle East
innovative solutions in the following business fields: +49 89 4129 12345
test and measurement, broadcast and media, secure [email protected]
communications, cybersecurity, radiomonitoring and
North America
radiolocation. Founded more than 80 years ago, this
1 888 TEST RSA (1 888 837 87 72)
independent company has an extensive sales and [email protected]
service network and is present in more than 70
countries. Latin America
+1 410 910 79 88
The electronics group is among the world market
[email protected]
leaders in its established business fields. The
company is headquartered in Munich, Germany. Asia Pacific
Regional headquarters are located in Singapore and +65 65 13 04 88
in Columbia, Maryland in the U.S. [email protected]
China
+86 800 810 82 28 |+86 400 650 58 96
[email protected]
Sustainable product design

ı Environmental compatibility and eco-footprint
ı Energy efficiency and low emissions
ı Longevity and optimized total cost of ownership
This document and any included programs may be

used only upon acceptance of the terms and
conditions of use as defined in the downloads area
of the Rohde & Schwarz Internet site.
R&S ® is a registered trademark of Rohde & Schwarz GmbH &

Co. KG Trade names are trademarks of the owners
PAD-T-M: 3573.7380.03/02.04/DE/
Rohde & Schwarz GmbH & Co. KG

Mühldorfstraße 15 | D - 81671 Munich
Phone + 49 89 4129 - 0 | Fax + 49 89 4129 – 13777
www.rohde-schwarz.com

Educational Note: Measuring With Digital Storage Oscilloscopes

Uploaded by

Copyright:

Available Formats

Educational Note: Measuring With Digital Storage Oscilloscopes

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Educational Note: Measuring With Digital Storage Oscilloscopes

Uploaded by

Copyright:

Available Formats

Measuring with digital storage

This educational note covers the theory and practice of digital

Please find the most up-to-date document on our homepage

Contents 1 Basics ....................................................................................................... 4

2 Preparing for the measurement exercises ..................................... 18

3 Basic measurements ........................................................................ 20

4 Documentation and storage ............................................................ 27

5 Advanced trigger settings................................................................ 32

6 Signal analysis using FFT ................................................................ 38

7 Analysis of protocol-based bus signals ......................................... 43

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 2

ı The R&S®HMO1002 Digital Oscilloscope is referred to as the HMO1002

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 3

Fig. 1: The R&S®HMO1002 digital storage oscilloscope.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 4

1.1.1 Operating concept and default settings

An oscilloscope typically displays a given variable as a function of another variable.

1 This corresponds to 50 mV/div, where div is the abbreviation for 'division'.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 5

Fig. 2: Basic settings for the horizontal and vertical systems.

Fig. 3: Measurement using the HMO1002.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 6

1.1.2 Signals and bandwidth

Signal integrity is key to precise and reproducible measurements. Signal integrity

Fig. 4: Frequency response of the HMO1002.

Oscilloscopes are frequently used to measure digital pulses. In theory, square-wave

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 7

ı The simple bandwidth is sufficient for simple decoding of signals, however.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 8

To keep the possible measurement errors at a minimum, the selected system

2 Probes without any active components, such as amplifiers.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 9

Fig. 5: Measurements using a probe.

Fig. 6: R&S®HZ154 probe with 10:1 and 1:1 attenuation ratios.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 10

measurements starting at about 50 MHz, an HF adjustment should additionally be

Fig. 7: Adjusting the HZ154 probe on the HMO1002.

Fig. 8 Exercise setups for oscilloscope measurements.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 11

1.2.1 Vertical resolution and dynamic range

n Bit count for the ADC

Fig. 9: Vertical resolution at different scalings.

1.2.2 Signal sampling and processing

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 12

Fig. 10: Effects of low sample rates.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 13

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 14

Fig. 11 Acquisition cycle for a digital oscilloscope.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 15

1.2.3 Triggering basics

Fig. 12: Simplified digital trigger setup.

Most oscilloscopes support, at a minimum, the following trigger conditions:

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 16

Fig. 13: Effects of various trigger settings.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 17

2 Preparing for the measurement exercises

Fig. 14: Correct use of an oscilloscope for measurements.

1MAA265-1e Rohde & Schwarz Measuring with digital storage oscilloscopes 18

Fig. 15: Performing the probe adjustment.