Service Manual: Viewsonic Vp2030B-1

Service Manual
ViewSonic VP2030b-1
Model No. VS10772
20” Color TFT LCD Display
(VP2030b-1_SM Rev. 1b Jan. 2007)

ViewSonic® 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright © 2007 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision SM Editing Date ECR Number Description of Changes Editor
1a 12/23/2005 Initial Release Jamie Chang
1b 01/05/2007 VS-E060426 Add 2nd panel source Jamie Chang
Viewsonic Corporation i Confidential - Do Not Copy VP2030b-1

TABLE OF CONTENTS
1. Precautions and Safety Notices 1
2. Specification 4
3. Front Panel Function Control Description 10
4. Circuit Description 13
5. Adjusting Procedure 26
6. Trouble Shooting Flow Chart 53
7. Recommended Spare Parts List 60
8. Exploded View And Exploded Parts List 63
9. Block Diagram 67
10. Schematic Diagrams 68
11. PCB Layout Diagrams 73
Viewsonic Corporation ii Confidential - Do Not Copy VP2030b-1

1. Precaution & Safety Notice
1. Caution :
No modification of any circuit should be attempted . Service work should only be performed after you are
thoroughly familiar with all of the following safety checks and servicing guide line
2. Safety Check :
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit.
These voltage are exposed in such areas as the associated transformer circuits .
3. POWER SUPPLY REQUIREMENTS

The external power converter for this display utilizes AC and DC cords , AC cord is detachable , but DC cord is
permanently attached . Any attempt to replace another adapter could result in serious problem on the display .
4. LEAKAGE CURRENT HOT CHECK

4-1 Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during this check.
4-2 Connect a 1500 ohm , 10 watt resistor , paralleled by a 0.15uF capacitor between each metallic part and a
good earth ground
4-3 Use an AC voltmeter with 1000 ohm / volt or more sensitivity and measure the AC voltage across the
combination 1500 ohm resistor and 0.15uF capacitor.
4-4 Move the resistor connection to each exposed metallic part and measure the voltage.
4-5 Reverse the polarity of the AC plug in the AC outlet and repeat the above measurement.
4-6 Voltage measured must not exceed 1.5 volt RMS, from any exposed metallic part to the ground. A leakage
current tester may be used in the above hot check, in which case any circuit measured must not exceed 1.0
milliamp. In the case of a measurement exceeding the 1.0 milliamp value, a rework is required to eliminate
the chance of a shock hazard .
AC VOLTMETER
0.15u
.
To Metal Parts 1500 10W Earth Ground
Viewsonic Corporation 1 Confidential - Do Not Copy VP2030b-1

Handling & Placing method
Correct methods : Incorrect Methods :

Only touch the metal-frame of the panel or the front cover of Surface of the panel is pressed by fingers & this may cause
the monitor . Do not touch the surface of the polarizer . “ MURA “

Take out the monitor with cushion Take out the monitor by grasping the LCD panel.
This may cause “ MURA“.

Place the monitor on a clean & soft foam pad . Place the monitor on foreign objects .
That could scratch the surface of panel

2. Specification
GENERAL specification
Test Resolution & Frequency 1600x1200 @ 60Hz

Test Image Size Full Size
Factory Default:
Contrast and Brightness Controls
Contrast = 70%, Brightness = 100%
VIDEO INTERFACE
Input Connector (refer the appendix A) D-Sub = DB-15 (Analog)

DVI-A = DVI-I (Analog)
DVI-D = DVI-I (Digital)
Default Input Connector Defaults to the first detected input
Equal to twice the weight of the monitor for
Video Cable Strain Relief
five minutes
Video Cable Connector DB-15 Pin out Compliant DDC/CI
Video RGB (Analog)
Video Signals Separate Sync / Composite Sync / SOG
TMDS (Digital)
Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals TTL
DDC/CI Compliant with Revision 1.0
Sync Compatibility Separate Sync / Composite Sync / SOG
Shall be compatible with all PC type
Video Compatibility computers, Macintosh computers, and after
market video cards
640 x 350, 640 x 400, 640 x 480, 720 x 400,
720 x 480, 720 x 576, 800 x 600, 832 x 624,
1024 x 768, 1152 x 864, 1152 x 870, 1280 x
Resolution Compatibility 720, 1280 x 768, 1280 x 960, 1280 x 1024,
1360 x 768, 1400 x 1050, 1440 x 900, 1600 x
1200, 1680 x 1050, 1920 x 1080, 1920 x 1200
Exclusions Not compatible with interlaced video

USB INTERFACE
Up Stream Connector B type USB port x1

Down Stream Connector A type USB port x4
Compatibility Compliant with Revision 2.0
Power The hub gets power from the display.
POWER SUPPLY
Internal Power Supply Delta EADP-64BF

Input Voltage Range 90 to 264 VAC
Input Frequency Range 47.5 to 63 Hertz
Short Circuit Protection Output can be shorted without damage
Over Current Protection 5.0 A typical at 12.0 VDC
Leakage Current 3.5mA (Max) at 254VAC / 60Hz
Efficiency 80 % typical at 115VAC Full Load
Fuse Internal and not user replaceable
Power Dissipation 64 Watts (typ)
Max Input AC Current 1.5 Arms @ 90VAC, 0.75 Arms @180VAC
50 A (max) @ 115VAC
Inrush Current (Cold Start)
90 A (max) @ 230VAC
Shall start and function properly when under
Power Supply Cold Start full load, with all combinations of input voltage,
input frequency, and operating temperature.
Shall be able to withstand an ANSI/IEEE
Power Supply Transient Immunity C62.41-1980 6000V 200 ampere ring wave
transient test with no damage.
Shall be able to withstand 1.5 times nominal
Power Supply Line Surge Immunity
line voltage for one cycle with no damage.
Shall be able to function properly, without
reset or visible screen artifacts, when ½ cycle
Power Supply Missing Cycle Immunity
of AC power is randomly missing at nominal
input.
The power supply shall not produce audible
noise that would be detectable by the user.
Audible shall defined to be in compliance with
Power Supply Acoustics
ISO 7779 (DIN EN27779:1991) Noise
measurements of machines acoustics. Power
Switch noise shall not be considered.
Power Saving Operation(Method) VESA DPMS Signaling
On Mode < 52 W (Typ) / 56 W (max)
Power Consumption
Active Off < 3 W
Recovery Time On Mode = N/A, Active Off < 8 sec

ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency

Horizontal Frequency 24 – 92 KHZ
Vertical Refresh Rate 50 – 85* HZ.
Maximum Pixel Clock 165 MHz
Sync Polarity Independent of sync polarity.
Timing Table
Digital - TMDS
Analog
Composite
Separated
Item Timing Remark
1 640 x 350 @ 70 Hz, 31.5 KHz ü ü SOG

ü ü
For Separated sync, Only horizontal full
2 640 x 350 @ 85 Hz, 37.9 KHz ü ü ü screen, The vertical position is at the
center.
For SOG sync, switch 640x400@60Hz
3 640 x 400 @ 60 Hz, 31.5 KHz ü ü ü ü and 640x480@60Hz by [1]+[2] short cut
key (primary = 640x480@60Hz)
For Separated Sync, Switch
640x400@70Hz and 720x400@70Hz by
4 640 x 400 @ 70 Hz, 31.5 KHz ü ü ü ü
[1]+[2] short cut key (primary =
640x400@70Hz)
640x400@85Hz and 720x400@85Hz by
5 640 x 400 @ 85 Hz, 37.9 KHz ü ü ü ü
640x400@85Hz)
6 640 x 480 @ 50 Hz, 24.7 KHz ü ü ü
8 640 x 480 @ 67 Hz, 35 KHz ü ü ü ü
9 640 x 480 @ 72 Hz, 37.9 KHz ü ü ü ü
10 640 x 480 @ 75 Hz, 37.5 KHz ü ü ü ü
11 640 x 480 @ 85 Hz, 43.3 KHz ü ü ü ü
12 720 x 400 @ 70 Hz, 31.5 KHz ü ü ü ü
13 720 x 400 @ 85 Hz, 37.9 KHz ü ü ü ü 640x400@85Hz and 720x400@85Hz by

640x400@85Hz)
14 720 x 480 @ 60 Hz, 31.5 KHz ü ü
15 720 x 576 @ 50 Hz, 31.3 KHz ü ü
16 800 x 600 @ 50 Hz, 24.7 KHz ü ü ü ü
17 800 x 600 @ 56 Hz, 35.1 KHz ü ü ü ü
18 800 x 600 @ 60 Hz, 37.9 KHz ü ü ü ü
19 800 x 600 @ 72 Hz, 48.1 KHz ü ü ü ü
20 800 x 600 @ 75 Hz, 46.9 KHz ü ü ü ü
21 800 x 600 @ 85 Hz, 53.7 KHz ü ü ü ü
22 832 x 624 @ 75 Hz, 49.7 KHz ü ü ü ü
For Separated and Composite sync,
Switch 1024x768@50Hz and
23 1024 x 768 @ 50 Hz, 39.6 KHz ü ü ü ü
1280x768@50Hz by [1]+[2] short cut key
(primary = 1024x768@50Hz)
24 1024 x 768 @ 60 Hz, 48.4 KHz ü ü ü ü
25 1024 x 768 @ 70 Hz, 56.5 KHz ü ü ü ü
26 1024 x 768 @ 72 Hz, 58.1 KHz ü ü ü ü
27 1024 x 768 @ 75 Hz, 60 KHz ü ü ü ü
28 1024 x 768 @ 75 Hz, 60.2 KHz ü ü ü ü
29 1024 x 768 @ 85 Hz, 68.7 KHz ü ü ü ü
30 1152 x 864 @ 75 Hz, 67.5 KHz ü ü ü ü
31 1152 x 870 @ 75 Hz, 68.7 KHz ü ü ü ü
32 1280 x 720 @ 50 Hz, 37.5 KHz ü ü
33 1280 x 720 @ 60 Hz, 45 KHz ü ü
34 1280 x 768 @ 50 Hz, 39.6 KHz ü ü ü ü
(primary = 1024x768@50Hz)
For analog sync, Switch
1280x768@60Hz and 1360x768@60Hz
35 1280 x 768 @ 60 Hz, 47.4 KHz ü ü ü
by [1]+[2] short cut key (primary =
1280x768@60Hz)
36 1280 x 768 @ 60 Hz, 47.8 KHz ü ü ü
37 1280 x 768 @ 75 Hz, 60.3 KHz ü ü ü ü
38 1280 x 768 @ 85 Hz, 68.6 KHz ü ü ü ü
39 1280 x 960 @ 50 Hz, 49.4 KHz ü ü ü ü
40 1280 x 960 @ 60 Hz, 59.7 KHz ü ü ü ü
41 1280 x 960 @ 75 Hz, 75.2 KHz ü ü ü ü
42 1280 x 960 @ 85 Hz, 85.9 KHz ü ü ü ü
43 1280 x 1024 @ 50 Hz, 52.7 KHz ü ü ü ü

44 1280 x 1024 @ 60 Hz, 64 KHz ü ü ü ü
45 1280 x 1024 @ 75 Hz, 80 KHz ü ü ü ü
46 1280 x 1024 @ 85 Hz, 91.1 KHz ü ü ü ü
1280x768@60Hz and 1360x768@60Hz
47 1360 x 768 @ 60 Hz, 47.7 KHz ü ü ü ü
by [1]+[2] short cut key (primary =
1280x768@60Hz)
48 1400 x 1050 @ 50 Hz, 54.1 KHz ü ü ü ü
1400x1050@60Hz and
49 1400 x 1050 @ 60 Hz, 64.7 KHz ü ü ü
1680x1050@60Hz by [1]+[2] short cut
50 1400 x 1050 @ 60 Hz, 65.3 KHz ü ü
1680x1050@60Hz by [1]+[2] short cut
51 1400 x 1050 @ 75 Hz, 82.3 KHz ü ü ü ü
52 1440 x 900 @ 60 Hz, 55.5 KHz ü ü ü ü
53 1440 x 900 @ 60 Hz, 59.9 KHz ü ü ü ü
54 1440 x 900 @ 75 Hz, 75 KHz ü ü ü ü
55 1440 x 900 @ 85 Hz, 84.8 KHz ü ü ü ü
56 1600 x 1200 @ 50 Hz, 61.8 KHz ü ü ü ü
57 1600 x 1200 @ 60 Hz, 75 KHz ü ü ü ü
1400x1050@60Hz and
58 1680 x 1050 @ 60 Hz, 64.7 KHz ü ü ü
1680x1050@60Hz by [1]+[2] short cut
59 1680 x 1050 @ 60 Hz, 65.3 KHz ü ü
1680x1050@60Hz by [1]+[2] short cut
60 1920 x 1080 @ 50 Hz, 28.1 KHz ü ü
61 1920 x 1080 @ 60 Hz, 33.8 KHz ü ü
62 1920 x 1200 @ 60 Hz, 74 KHz ü ü ü ü
*1. Tolerance ≧ ±2KHz. (if the range dose not cover other timing mode)
*2. Any timing not in the list, it should display as normal or show on “OUT OF RANGE” OSD message without
blanking.
*3. The image quality of 85Hz mode might be worse than 75Hz.

TFT LCD PANEL
1st Source Panel

Model number AUO M201UN02 V.5
Type Active Matrix TFT, PMVA technology
Active Size 20.1"
Pixel Arrangement RGB Vertical Stripe
Pixel Pitch 0.255 mm
Glass Treatment Anti-Glare
# of Backlights 6 CCFL
Backlight Life 50000 Hrs (Min)
Luminance (Center) – 300 cd/m2 (Typ after 30 minute warm up)
CT = 6500K, 240 cd/m2 (Min after 30 minute warm up)
Contrast/ Brightness = Max
Brightness Uniformity 80% (typ); 75% (min)
Contrast Ratio 1000 :1 (Typ)
700 : 1 (Min)
Color Depth 16.7 million colors (8 bit panel)
170 degrees (Typ) @ CR>10
Horizontal Viewing Angle
150 degrees (Min) @ CR>10
Vertical Viewing Angle
On/Off
Typical = 16 ms (Tr = 11 ms; Tf = 5 ms)
Response Time
Maximun = 22 ms (Tr = 15 ms; Tf = 7 ms)
10%-90% @ Ta=25°C
GTG
8 ms (Avg)
Mercury 3.5 mg per lamp
Panel Defects Please see Panel Quality Specifications.
*The average of measured value from monthly shipment shall be equal or better than the Typical value above.
2nd Source Panel

Model number AUO M201UN02 V.6
Type Active Matrix TFT, PMVA technology
Active Size 20.1"
Pixel Arrangement RGB Vertical Stripe
Pixel Pitch 0.255 mm
Glass Treatment Anti-Glare
# of Backlights 6 CCFL
Backlight Life 50000 Hrs (Min)
Luminance (Center) – 300 cd/m2 (Typ after 30 minute warm up)
CT = 6500K, 240 cd/m2 (Min after 30 minute warm up)
Contrast/ Brightness = Max
Brightness Uniformity 80% (typ); 75% (min)
Contrast Ratio 1000 :1 (Typ)
700 : 1 (Min)
Color Depth 16.7 million colors (8 bit panel)
Horizontal Viewing Angle
Vertical Viewing Angle
On/Off
Typical = 16 ms (Tr = 11 ms; Tf = 5 ms)
Response Time
Maximun = 22 ms (Tr = 15 ms; Tf = 7 ms)
10%-90% @ Ta=25°C
GTG
8 ms (Avg)
Mercury 3.5 mg per lamp
Panel Defects Please see Panel Quality Specifications.
*The average of measured value from monthly shipment shall be equal or better than the Typical value above.

3. Front Panel Function Control Description
Main Menu
with on view
Front Control Panel

shown below in detail

ViewSonic VP2030
Main Menu Controls

Adjust the menu items shown below by using the up and down buttons.
A. Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and
distortion. Press the [2] button to obtain a sharper image.
NOTE: Auto Image Adjust works with most common video cards. If this function does not work on your LCD
display, then lower the video refresh rate to 60 Hz and set the resolution to its pre -set value.
B. Contrast adjusts the difference between the image background (black level) and the foreground (white level).
C. Brightness adjusts the lamps current to control the screen brightness.
D. Color Adjust provides several color options: preset color temperatures and Custom User Color which allows you
to adjust red (R), green (G), and blue (B). The factory setting for this product is 6500K (6500° Kelvin).
sRGB ─ Standard color space proposed by Microsoft and HP.
9300K — Adds blue to the screen image for cooler white (used in most office settings with fluorescent lighting).
7500K — Adds blue to the screen image for cooler white
5400K — Adds red to the screen image for warmer white and richer red.
5000K — Adds red to the screen image for warmer white and richer red.
Custom User Color — Individual adjustments for red, green, and blue.
1 To select color (R, G or B) press button [2].
2 To adjust selected color, press or .
3 When you are finished making all color adjustments, press button [1] twice.
E. Information displays the timing mode (video signal input) coming from the graphics card in your computer. See
your graphic card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).
VESA 1280 x 1024 @ 60 Hz (recommended) means that the resolution is 1280 x 1024 and the refresh rate is 60
Hertz.
F. Manual Image Adjust controls are explained below:
PIP (Picture in Picture) features are explained below:
PIP enables Picture in Picture function.
PIP Position is for user to adjust the position of PIP. Press button [2] to enter the PIP H. Position and use
or to adjust the PIP horizontal position. User can press [2] to enter V. Position and use or to
adjust the PIP vertical position.
PIP SWAP is for user to swap the signal in main window to daughter window while the signal of
daughter window will be displayed in main window.
H. Size (Horizontal Size) adjusts the width of the screen image.
NOTE: Vertical size is automatic with your LCD display.
H./V. Position adjusts horizontal and vertical position of the screen image. You can toggle between Horizontal
and Vertical by pressing button [2]. Horizontal moves the screen image to the left or to the right. Vertical moves
the screen image up and down.
Fine Tune sharpens focus by aligning the illuminated text and/or graphic characters.

Sharpness adjusts the clarity and focus of the screen image. This feature is disabled when the input signal is
1600x1200@60Hz analog signal.
Scaling features are explained below:
Fill All - the signal will be displayed on the whole screen and wide signal will be adjusted to 4:3 ratio.
Fill Aspect Ratio – the width of the signal will fit the screen horizontally while the vertical directions may
not fit the screen (if the input is wide signal)
1:1 – the signal will be displayed on the center of the screen with 1:1 ratio. This means you may see the
signal at the center of the screen while it is surrounded by black area.
G. Setup Menu controls are explained below:
Language allows you to choose the language used in the menus and control screens.
Resolution Notice displays the recommended resolution for this LCD display.
Enable allows the Resolution Notice to appear on-screen.
Disable will not allow the Resolution Notice to appear on-screen.
OSD Timeout sets the length of time an on-screen display screen is displayed. For example, with a“15
second” setting, if a control is not pushed within 15 seconds, the display OSD disappears.
OSD Position allows you to move the on-screen display menus and control screens.
H. Memory Recall returns adjustments to the original factory settings if the display is operating in a factory Preset
Timing Mode listed in this user guide.

4. Circuit Description
1. Outline
1.1 Buttons on the front panel: Power On/Off button, button 2 (ENTER / INPUT SELECT), up arrow button, down
arrow button, button 1 (MENU).
1.2 D-sub 15pin connector, DVI-I connector and AC-IN jack are located on the back side of the cabinet.
1.3 OSD menu includes the following function;
Auto Image Adjust (only active under analog input)
l Contrast/Brightness
l Input Select
l Color Adjust
l Information
l Manual Image Adjust
l Setup Menu
l Memory Recall
1.4 Contrast and Brightness can be directly controlled with UP / DOWN buttons.
2. Connectors
2.1 AC inlet : CEE22 typed connector
2.2 Video signal connector for analog input: 15P Mini D-Sub
CN6 PIN MNEMONIC SIGNAL

10
1
6
2
7
3
8
4
9
5
DB15HD 1 RV Red Video

16 17
2 GV Green Video
3 BV Blue Video
11
12
13
14
15
4 NC None
5 GND Ground (DDC return)
6 RG Red GND
7 GG Green GND
8 BG Blue GND
9 +5V +5V (for DDC)
10 SG Sync GND
11 NC None
12 SDA DDC Data
13 HS Horizontal Sync
14 VS Vertical Sync
15 SCL DDC Clock

2.3 Video signal connector for digital input: 29pin DVI-D,DVI-A connector
CN2 Pin No. Signal Name Description

25 1 RX2- TMDS negative differential input,
1
RX2-
2
RX2+
3
channel 2
GND
4
RX4-
RX4+
5 2 RX2+ TMDS positive differential input,
6
SCL
7
SDA
8
channel 2
VS
RX1-
9 3 GND Logic Ground
10
RX1+
11
GND
12
4 RX4- Reserved. No connection
RX3-
13
RX3+
5V
14 5 RX4+ Reserved. No connection
15
GND
16
HP 6 SCL DDC2B Clock
17
RX0-
RX0+
18 7 SDA DDC2B Data
19
GND
20
RX5-
21
8 VS Reserved. No connection
RX5+ 22
GND
RXC+
23 9 RX1- TMDS negative differential input,
24
RXC-
C1
channel 1
RED C2
GRN C3 10 RX1+ TMDS positive differential input,
BLU C4
HS C5
GND channel 1
26
11 GND Logic Ground
DVI-I 12 RX3- Reserved. No connection
13 RX3+ Reserved. No connection
14 +5V Power
15 GND Logic Ground
16 HP SENSE Pin, Pull High
17 RX0- TMDS negative differential input,
channel 0
18 RX0+ TMDS positive differential input,
channel 0
19 GND Logic Ground
20 RX5- Reserved. No connection
21 RX5+ Reserved. No connection
22 GND Logic Ground
23 RXC+ TMDS positive differential input,
reference clock
24 RXC- TMDS negative differential input,
reference clock
C1 RED Red Video for DVI-A only
C2 GRN Green Video for DVI-A only
C3 BLU BlueVideo for DVI-A only
C4 HS Horizontal Sync
C5 GND GND

3. ELECTRICAL SPECIFICATIONS
3.1 Standard conditions
Display Area 408.0 x 306.0 mm

Video Signal 0.7Vpp
Contrast Default
Brightness Max.
Ambient 20 +/- 5 °
C
Input AC 110~ 240V
Warming up > 30 min
Display 1600X1200
3.2 POWER
3.2.1 Power supply
Input voltage 100~240Vac
Power frequency 50~60Hz
Input current <1.5Arms@90Vac
Inrush current
80A(Max) at 230Vac(cold start)
Power consumption 52W(typical);56W(Max)
3.2.2 Power Management
State Power Indicator
On 56Watts Green
Standby < 3Watts Amber

Off <3Watts Off
3.3 Acceptable timing

If the timing is within following specification, this LCD display can automatically function with a certain position.
Horizontal: Sync frequency: 24~92 kHz
Vertical: Sync frequency: 50~85Hz

3.4 Signal level and input impedance
3.4.1 Video Signal level: 0.7Vp-p Video signal.
3.4.2 Sync Signal level
H/V Separate: TTL level
3.4.3 Input impedance
Analog video input: 75 ohm
Digital video input: 100 ohm
Sync input: > 1 k ohm
4. SIGNAL CABLE: Signal cable with Mini D-Sub 15P connectors at both ends. Length: 1.8 meter.

5. EDID data
AUO
Analog EDID
//////////Displaying Monitor EDID//////////
128 BYTES OF EDID CODE:
0 1 2 3 4 5 6 7 8 9
________________________________________
0 | 00 FF FF FF FF FF FF 00 5A 63
10 | 1C 13 01 01 01 01 01 0F 01 03
20 | 0E 29 1F 78 2E 30 85 A6 56 4A
30 | 99 24 14 50 54 BF EF 80 A9 40
40 | 90 4F 90 40 81 80 81 40 71 4F
50 | 01 01 01 01 48 3F 40 30 62 B0
60 | 32 40 40 C0 13 00 98 32 11 00
70 | 00 1E 00 00 00 FF 00 50 53 42
80 | 30 35 30 31 30 30 30 30 31 0A
90 | 00 00 00 FD 00 32 4B 1E 5C 11
100 | 00 0A 20 20 20 20 20 20 00 00
110 | 00 FC 00 56 50 32 30 33 30 20
120 | 53 45 52 49 45 53 00 FD
______________________________________________________________________
(08-09) ID Manufacturer Name ________________ = VSC
(11-10) Product ID Code _____________________ = 131C
(12-15) Last 5 Digits of Serial Number ______ = Not Used
(16) Week of Manufacture _________________ = 01
(17) Year of Manufacture _________________ = 2005
(10-17) Complete Serial Number ______________ = See Descriptor Block
(18) EDID Version Number _________________ = 1
(19) EDID Revision Number ________________ = 3
(20) VIDEO INPUT DEFINITION:
Analog Signal
0.700, 0.300 (1.000 Vp-p)
Separate Syncs, Composite Sync, Sync on Green
(21) Maximum Horizontal Image Size ________________ = 410 mm
(22) Maximum Vertical Image Size __________________ = 310 mm
(23) Display Gamma ________________________________ = 2.20
(24) Power Management and Supported Feature(s):
Active Off/Very Low Power, Standard Default Color Space,
Preferred Timing Mode
Display Type = R/G/B Color

(25-34) CHROMA INFO:
Red X - 0.648 Green X - 0.289 Blue X - 0.143 White X - 0.313
Red Y - 0.339 Green Y - 0.598 Blue Y - 0.078 White Y - 0.329
(35) ESTABLISHED TIMING I:
720 X 400 @ 70Hz (IBM,VGA)
640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 67Hz (Apple,Mac II)
640 X 480 @ 72Hz (VESA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 56Hz (VESA)
800 X 600 @ 60Hz (VESA)
(36) ESTABLISHED TIMING II:
800 X 600 @ 72Hz (VESA)
800 X 600 @ 75Hz (VESA)
1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 70Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)
(37) Manufacturer's Reserved Timing:
(38-53) Standard Timing Identification:
1600 X 1200 @60Hz
1400 X 1050 @75Hz
1400 X 1050 @60Hz
1280 X 1024 @60Hz
1280 X 960 @60Hz
1152 X 864 @75Hz
Not Used
Not Used
______________________________________________________________________
(54-71) Detailed Timing / Descriptor Block 1:
1600x1200 Pixel Clock: 162.00 MHz
______________________________________________________________________
Horizontal Image Size: 408 mm Vertical Image Size: 306 mm
Refreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:
Active Time: 1600 pixels Blanking Time: 560 pixels
Sync Offset: 64 pixels Sync Pulse Width: 192 pixels
Border: 0 pixels Frequency: 75.00 KHz

Vertical:
Active Time: 1200 lines Blanking Time: 50 lines
Sync Offset: 1 lines Sync Pulse Width: 3 lines
Border: 0 lines Frequency: 60.00 Hz
Digital Separate, Horizontal Polarity (+) Vertical Polarity (+)
______________________________________________________________________
Monitor Serial Number:

PSB050100001
______________________________________________________________________
Monitor Range Limits:

Min Vertical Freq - 50 Hz
Max Vertical Freq - 75 Hz
Min Horiz. Freq - 30 KHz
Max Horiz. Freq - 92 KHz
Pixel Clock - 170 MHz
Secondary GTF - Not Supported
______________________________________________________________________
Monitor Name:
VP2030 SERIES
(126) No Extension EDID Block(s)

Digital EDID
128 BYTES OF EDID CODE:

0 1 2 3 4 5 6 7 8 9
________________________________________
0 | 00 FF FF FF FF FF FF 00 5A 63
10 | 1C 13 01 01 01 01 01 0F 01 03
20 | 80 29 1F 78 2E 30 85 A6 56 4A
30 | 99 24 14 50 54 BF EF 80 A9 40
40 | 90 4F 90 40 81 80 81 40 71 4F
50 | 31 0A 01 01 48 3F 40 30 62 B0
60 | 32 40 40 C0 13 00 98 32 11 00
70 | 00 1E 00 00 00 FF 00 50 53 42
80 | 30 35 30 31 30 30 30 30 31 0A
90 | 00 00 00 FD 00 32 4B 1E 5C 11
100 | 00 0A 20 20 20 20 20 20 00 00
110 | 00 FC 00 56 50 32 30 33 30 20
120 | 53 45 52 49 45 53 00 52
______________________________________________________________________
(08-09) ID Manufacturer Name ________________ = VSC
(11-10) Product ID Code _____________________ = 131C
(12-15) Last 5 Digits of Serial Number ______ = Not Used
(16) Week of Manufacture _________________ = 01
(17) Year of Manufacture _________________ = 2005
(10-17) Complete Serial Number ______________ = See Descriptor Block
(18) EDID Version Number _________________ = 1
(19) EDID Revision Number ________________ = 3
(20) VIDEO INPUT DEFINITION:
Digital Signal
Non - VESA DFP 1.x Compatible
(21) Maximum Horizontal Image Size ________________ = 410 mm

(22) Maximum Vertical Image Size __________________ = 310 mm
(23) Display Gamma ________________________________ = 2.20
(24) Power Management and Supported Feature(s):
Active Off/Very Low Power, Standard Default Color Space,
Preferred Timing Mode
Display Type = R/G/B Color
(25-34) CHROMA INFO:
Red X - 0.648 Green X - 0.289 Blue X - 0.143 White X - 0.313
Red Y - 0.339 Green Y - 0.598 Blue Y - 0.078 White Y - 0.329

(35) ESTABLISHED TIMING I:
720 X 400 @ 70Hz (IBM,VGA)
640 X 480 @ 60Hz (IBM,VGA)
640 X 480 @ 72Hz (VESA)
640 X 480 @ 75Hz (VESA)
800 X 600 @ 56Hz (VESA)
800 X 600 @ 60Hz (VESA)
(36) ESTABLISHED TIMING II:
800 X 600 @ 72Hz (VESA)
800 X 600 @ 75Hz (VESA)
1024 X 768 @ 60Hz (VESA)
1024 X 768 @ 70Hz (VESA)
1024 X 768 @ 75Hz (VESA)
1280 X 1024 @ 75Hz (VESA)
(37) Manufacturer's Reserved Timing:
(38-53) Standard Timing Identification:
1600 X 1200 @60Hz
1400 X 1050 @75Hz
1400 X 1050 @60Hz
1280 X 1024 @60Hz
1280 X 960 @60Hz
1152 X 864 @75Hz
640 X 400 @70Hz
Not Used
______________________________________________________________________
1600x1200 Pixel Clock: 162.00 MHz
______________________________________________________________________
Horizontal Image Size: 408 mm Vertical Image Size: 306 mm
Refreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:
Active Time: 1600 pixels Blanking Time: 560 pixels
Sync Offset: 64 pixels Sync Pulse Width: 192 pixels
Border: 0 pixels Frequency: 75.00 KHz
Vertical:
Active Time: 1200 lines Blanking Time: 50 lines

Sync Offset: 1 lines Sync Pulse Width: 3 lines
Border: 0 lines Frequency: 60.00 Hz
Digital Separate, Horizontal Polarity (+) Vertical Polarity (+)
______________________________________________________________________
Monitor Serial Number:

PSB050100001
______________________________________________________________________
Monitor Range Limits:

Min Vertical Freq - 50 Hz
Max Vertical Freq - 75 Hz
Min Horiz. Freq - 30 KHz
Max Horiz. Freq - 92 KHz
Pixel Clock - 170 MHz
Secondary GTF - Not Supported
______________________________________________________________________
Monitor Name:
VP2030 SERIES
(126) No Extension EDID Block(s)

(127) CheckSum OK

6. THEORY OF OPERATION
This section describes the function of the LCD monitor per functional block.
This monitor includes MB board, power board and button board and USB board
6.1 MB BOARD
The MB board is a Four-layer, single -landed design with ground and internal planes provided. DC power from the
power board enters the board through a 8P connector. The other connector on the board is for the button board. The
VGA cable is a signal cable that carries the video, sync and DDC signals from the PC VGA adapter. This system
board consists of 4 functional areas: flat panel controller, MCU with flash ROM, and power regulators
USB function.
6.1.1 Flat panel controller… Gm1601(U21)
The heart of the system board is the Realtek Gm1601. The Gm1601 is a graphics processing IC designed for
LCD monitors. It provides all key IC functions required for LCD displays. On-chip functions include a
high-speed triple -ADC, PLL, high scaling engine and OSD controller.
a) Clock Generation :
Crystal Input Clock (TCLK and XTAL). This is the input pair to an internal crystal oscillator and
corresponding logic. A 14.318 MHz crystal is recommended.
b) Analog to Digital Converter:
The Gm1601 chip has three ADC's (analog-to-digital converters), one for each color (red, green and
blue) .The analog RGB signals are connected to Gm1601 as described below
Pin Name Pin Number
Red + D2
Red - D1
Green + C2
Green - C1
Blue + B2
Blue - B1
c) SST 39VF040 Micro Controller: The SST 39VF040 micro controller (MCU) serves as the system micro
controller. It programs the Gm1601 and manages other devices in the system such as the keypad
Pin number Pin Number Usage
AE24 Key / Power on ,off
P3 NV_RAM (U4) SDA
P4 NV_RAM (U4) SCL
AF24 Key_down
AF26 Key_right
AF25 Key_up
AE25 Key_left
AD24 Key_select
D25 LED_red
D26 LED_green

AC2 LCD panel power1 on / off control
C25 Backlight on / off control
d) Panel interface (Pin B1,B2,C1,C2,D1,D2,A6,B6,A8,B8,A9,B9,A10,B10,) : The Gm1601 driver interface is
highly programmable.
6.1.2 Power Regulator AIC1577 (U23), AP1084 (U16,U20),LT1117(U18) : The AIC1577 is a current switching
regulator control IC containing the primary functions required for DC to DC converters and external
NMOS STEP-DOWN PWM controller ,operating input voltaqge from 4.5V to 24V The desired output
voltage is determined by the equation, Volt = 0.8[ ( R218+R219) / R218]. In this case, the output voltage is
5 Volts. The AIC1577 is a low dropout operation
6.1.3 Power Regulator AP1084 (U16,U20): The AP1084 is a low dropout positive adjustable or fixed mode
regulator with minimum of 5A output current capability. Specifically designed to provide supply for low
voltage IC and low current 3.3V logic supply. AP1084 is guaranteed to have lower than 1.4V dropout at
full load current ,provide well-regulated output of 1.25 to 3.3 with 4.7 to 12V input supply.
6.1.4 Power Regulator LT1117(U18): The LT1117 is a low drop voltage regulator ,provide up to 800 mA of
output current. Concerning fixed version, are offered the output voltage:1.2V, 1.8V, 2.5V, 2.85V, 3.0V,
3.3V, the regulator to reach a very tight output voltage tolerance, within ±1% at 25?C. The adjustable
LD1117 is pin to pin compatible with the other LD1117.
6.3 Power (Inverter) Board

This is a specific power (inverter) board for VP2030B monitor with output of 56W /12V / 2.4A and 20V/1.8A. It
provides 20 VDC to drive the four cold cathode fluorescence tubes in the backlight.
6.3.1 The inverter's electrical specification is described below.
Input Rated Input Voltage 20Vdc

Input Voltage Range 19 ~ 21 Vdc
Input Current 1.8A(MAX)
On / Off control Voltage 2.5~5.25 for on , 0~1 for off
Output Rated Output Strike-on Voltage 1800Vrms
Rated Output Voltage 700~900Vrms
Rate Output Frequency 35~80KHz
Rated Output Current 5.5~8.0 mA
6.3.2 power
This is a general purpose AC / DC adapter which converts 90~240 Vac to a stabilized DC voltage: 12 Volts,
with a rated output current of 2.4A. The electrical specification is described below.
Rated Input Voltage 90~240 Vac , 50 / 60Hz

Operation Input Voltage 90~260 Vac , 47 ~ 63Hz

Input Current <2.4A
Inrush Current <80A@230Vac
Standby Input Voltage 12Vdc
Output Voltage Regulation +/-5%
Output Ripple & Noise 300mVp-p
Rate Output Current <2.4A
6.4 USB Board: Include one Up-Stream port and four Down-Stream ports each one port cann’t exceed 1A
6.5 DDC/CI: VP2030B monitor can use Perfect Suit offer DDC/CI function, make use of Perfect Suit sofeware
to substitute OSD function even more , for instance ,the adjustment of the color temperature, adjustment of
the luminance ,the more special one is the rotation of the screen.

5. Adjusting Procedure
Function test
(1) Test equipment
Color video signal and pattern generator (or PC with WUXGA resolution)
(2) Test condition
Before function testing and alignment, the unit must warm up for at least 30 minutes under the following
conditions:
1. Room temperature
2. With full-white screen , RGB , black pattern
3. with cycled display modes.
2. Test display modes
Timing Table
Digital - TMDS
Analog
Composite
Separated
Item Timing Remark
SOG
1 640 x 350 @ 70 Hz, 31.5 KHz ü ü ü ü

For Separated sync, Only horizontal full
2 640 x 350 @ 85 Hz, 37.9 KHz ü ü ü screen, The vertical position is at the
center.
key (primery = 640x480@60Hz)
640x400@70Hz and 720x400@70Hz by
4 640 x 400 @ 70 Hz, 31.5 KHz ü ü ü ü
[1]+[2] short cut key (primery =
640x400@70Hz)
640x400@85Hz and 720x400@85Hz by
5 640 x 400 @ 85 Hz, 37.9 KHz ü ü ü ü
640x400@85Hz)
6 640 x 480 @ 50 Hz, 24.7 KHz ü ü ü
8 640 x 480 @ 67 Hz, 35 KHz ü ü ü ü
9 640 x 480 @ 72 Hz, 37.9 KHz ü ü ü ü
10 640 x 480 @ 75 Hz, 37.5 KHz ü ü ü ü
11 640 x 480 @ 85 Hz, 43.3 KHz ü ü ü ü
12 720 x 400 @ 70 Hz, 31.5 KHz ü ü ü ü
13 720 x 400 @ 85 Hz, 37.9 KHz ü ü ü ü
640x400@85Hz and 720x400@85Hz by

640x400@85Hz)
14 720 x 480 @ 60 Hz, 31.5 KHz ü
15 720 x 576 @ 50 Hz, 31.3 KHz ü ü Use Hot Key to switch the color.
16 800 x 600 @ 50 Hz, 24.7 KHz ü ü ü ü
17 800 x 600 @ 56 Hz, 35.1 KHz ü ü ü ü
18 800 x 600 @ 60 Hz, 37.9 KHz ü ü ü ü
19 800 x 600 @ 72 Hz, 48.1 KHz ü ü ü ü
20 800 x 600 @ 75 Hz, 46.9 KHz ü ü ü ü
21 800 x 600 @ 85 Hz, 53.7 KHz ü ü ü ü
22 832 x 624 @ 75 Hz, 49.7 KHz ü ü ü ü
23 1024 x 768 @ 50 Hz, 39.6 KHz ü ü ü ü
(primery = 1024x768@50Hz)
24 1024 x 768 @ 60 Hz, 48.4 KHz ü ü ü ü
25 1024 x 768 @ 70 Hz, 56.5 KHz ü ü ü ü
26 1024 x 768 @ 72 Hz, 58.1 KHz ü ü ü ü
27 1024 x 768 @ 75 Hz, 60 KHz ü ü ü ü
28 1024 x 768 @ 75 Hz, 60.2 KHz ü ü ü ü
29 1024 x 768 @ 85 Hz, 68.7 KHz ü ü ü ü
30 1152 x 864 @ 75 Hz, 67.5 KHz ü ü ü ü
31 1152 x 870 @ 75 Hz, 68.7 KHz ü ü ü ü
32 1280 x 720 @ 50 Hz, 37.5 KHz ü ü
33 1280 x 720 @ 60 Hz, 45 KHz ü ü
34 1280 x 768 @ 50 Hz, 39.6 KHz ü ü ü ü
(primery = 1024x768@50Hz)
1280x768@60Hz and 1360x768@60Hz
35 1280 x 768 @ 60 Hz, 47.4 KHz ü ü ü
by [1]+[2] short cut key (primery =
1280x768@60Hz)
36 1280 x 768 @ 60 Hz, 47.8 KHz ü ü ü
37 1280 x 768 @ 75 Hz, 60.3 KHz ü ü ü ü
38 1280 x 768 @ 85 Hz, 68.6 KHz ü ü ü ü
39 1280 x 960 @ 50 Hz, 49.4 KHz ü ü ü ü
40 1280 x 960 @ 60 Hz, 59.7 KHz ü ü ü ü
41 1280 x 960 @ 75 Hz, 75.2 KHz ü ü ü ü
42 1280 x 960 @ 85 Hz, 85.9 KHz ü ü ü ü

43 1280 x 1024 @ 50 Hz, 52.7 KHz ü ü ü ü
44 1280 x 1024 @ 60 Hz, 64 KHz ü ü ü ü
45 1280 x 1024 @ 75 Hz, 80 KHz ü ü ü ü
46 1280 x 1024 @ 85 Hz, 91.1 KHz ü ü ü ü
1280x768@60Hz and 1360x768@60Hz
47 1360 x 768 @ 60 Hz, 47.7 KHz ü ü ü ü
by [1]+[2] short cut key (primery =
1280x768@60Hz)
48 1400 x 1050 @ 50 Hz, 54.1 KHz ü ü ü ü
1400x1050@60Hz and
49 1400 x 1050 @ 60 Hz, 64.7 KHz ü ü ü
1680x1050@60Hz by [1]+[2] short cut
50 1400 x 1050 @ 60 Hz, 65.3 KHz ü ü
1680x1050@60Hz by [1]+[2] short cut
51 1400 x 1050 @ 75 Hz, 82.3 KHz ü ü ü ü
52 1440 x 900 @ 60 Hz, 55.5 KHz ü ü ü ü
53 1440 x 900 @ 60 Hz, 59.9 KHz ü ü ü ü
54 1440 x 900 @ 75 Hz, 75 KHz ü ü ü ü
55 1440 x 900 @ 85 Hz, 84.8 KHz ü ü ü ü
56 1600 x 1200 @ 50 Hz, 61.8 KHz ü ü ü ü
57 1600 x 1200 @ 60 Hz, 75 KHz ü ü ü ü
1400x1050@60Hz and
58 1680 x 1050 @ 60 Hz, 64.7 KHz ü ü ü
1680x1050@60Hz by [1]+[2] short cut
59 1680 x 1050 @ 60 Hz, 65.3 KHz ü ü
1680x1050@60Hz by [1]+[2] short cut
60 1920 x 1080 @ 50 Hz, 28.1 KHz ü ü
61 1920 x 1080 @ 60 Hz, 33.8 KHz ü ü
62 1920 x 1200 @ 60 Hz, 74 KHz ü ü ü ü
*1. Tolerance ≧ ±2KHz. (if the range dose not cover other timing mode)
*2. Any timing not in the list, it should display as normal or show on “OUT OF RANGE” OSD message without
blanking.
*3. The image quality of 85Hz mode might be worse than 75Hz.

Primary Presets
1600x1200 @ 60Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
Changing Modes
● Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding “Auto Adjust” time
● Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting when execute
“Auto Adjust”
● The monitor needs to do “Auto Adjust” the first time a new mode is detected
(see section “0 -Touch™ Function Actions”)
● While running Change Mode, Auto Adjust or Memory Recall, the image shall blank
3. Test pattern
Item Test condition Pattern Specification Remark
1 Frequency & performance Cross-hatch pattern No noise is allowed, all colors must Pattern 1
be clear
2 Monitor saturation 16-gray scale pattern 3 to 4 levels must be saturated when Pattern 2
brightness and contrast are set to
100%
3 RGB color performance RGB color Check the color temperature of Pattern 3,
RGB signal color 4, 5
4 Sub-pixel defect RGB color Check the sub-pixel defect Pattern 3,
4,5
5 Full white Full white Check the brightness and contrast Pattern 6
ratio, and check for bright pixel
defects
6 Full black Full black Pattern 7
7. 5-cycle pattern 5-cycle pattern Check the BU Pattern 8
8. 1-dot pattern 1-dot pattern Check the flicker Pattern 9

Pattern 1 Pattern2
Pattern 3 Pattern4
Pattern 5 Pattern6

Pattern 7 Pattern 8
Pattern 9

OSD Function Menu
A. When in Analog Input Mode

1. Main Menu
Press the [1] (Menu) button to enter the Main Menu:
Press the [▲] button to highlight the previous item or the [▼] button to highlight
the next item.
Press the [1] (Menu) button to exit the Main Menu.
(1) Auto Image Adjust Page:
Press the [2] button to execute the auto image adjust function.
Press the [1] button to exit the page.
(2) Contrast/Brightness Page:

Press the [2] button to enter the contrast adjustment page.
1) Contrast Item
Press the [▲] button to increase the contrast.
Press the [▼] button to decrease the contrast.
Press the [2] button to enter the brightness adjustment page.
2) Brightness Item
Press the [▲] button to increase the brightness.
Press the [▼] button to decrease the brightness.
(3) Input Select Page:

Press the [2] button to switch to digital input mode.
(4) Audio Adjust Page:

Press the [▲] button to increase the volume.
Press the [▼] button to decrease the volume.
Press the [2] button to enable or disable mute function .
(5) Color Adjust Page:

Press the [2] button to enter the color adjustment page.
Press the [▲] button to highlight the previous item or the [▼] button to
highlight the next item.
1) sRGB Item
2) 9300K Item
3) 6500K Item
4) 5400K Item
5) 5000K Item
Press the [2] button to select the currently highlighted item.
Press the [1] button to exit the currently highlighted item.
6) User Color Item
Press the [2] button to enter the user color page.

Red, Green, Blue Options:
Press the [2] button to cycle among the colors.
Press the [▲] button to increase the selected color level.
Press the [▼] button to decrease the selected color level.
(6) Information Page:

Press the [2] button to enter the information page.
Press the [1] button to exit the information page.
(7) Manual Image Adjust Page:

Press the [2] button to enter the manual image adjustment page.
1) H./V. Position Item
Press the [2] button to enter the horizontal/vertical postion adjustment page.
a) Horizontal Position:
Press the [2] button to enter the vertical position adjustment page.
Press the [▲] button to shift the image to the right.
Press the [▼] button to shift the image to the left.
b) Vertical Position:
Press the [2] button to return to the horizontal position adjustment page.
Press the [▲] button to shift the image upward.
Press the [▼] button to shift the image downward.
2) Horizontal Size Item

Press the [2] button to enter the horizontal size adjustment page.
Press the [▲] button to make the image wider.
Press the [▼] button to make the image narrower.
3) Fine tune Item

Press the [2] button to enter the fine tuning page.
Press “[▲]” Button to adjust character position in one direction.
Press “[▼]“Button to adjust character position in the other direction.
4) Sharpness Item
Press the [2] button to enter the sharpness adjustment page.
Press “[▲]” Button to increase image sharpness.
Press “[▼]“ Button to decrease image sharpness.
(8) Setup Menu Page:

Press the [2] button to enter the setup menu page.
1) Language Select Item
Press the [2] button to enter the language selection page.
English, French… Option
Press the [2] button to select the language.
2) Resolution Notice Item

Press the [2] button to enter the resolution notice page.
Enable, Disable Option
Press the [2] button to select the highlighted option.
Press the [▲] button to highlight the previous option or the [▼] button
to highlight the next option.
3) OSD Position Item

Press the [2] button to enter the OSD position adjustment page.
a) Horizontal Position Option
Press the [▲] button to shift the menu to the right.
Press the [▼] button to shift the menu to the left.
b) Vertical Position Option:

Press the [2] button to enter the horizontal position adjustment page.
Press the [▲] button to shift the menu upward.
Press the [▼] button to shift the menu downward.
4) OSD Time Out Item

Press the [2] button to enter the OSD time out adjustment page.
Press the [▲] button to increase the OSD time out.
Press the [▼] button to decrease the OSD time out.
5) OSD Background Item

Press the [2] button to enter the OSD background selection page.

(9) Memory Recall Page

Press the [2] button to execute the memory recall function.
2. Other Menu:
This “shortcut” menu is directly accessible without bringing up the OSD.
(1) Contrast Dialog
Press the [▲] or [▼] button to enter the Contrast Dialog.
Press the [1] button to exit the Contrast Dialog.
Press the [2] button to enter the Brightness Dialog.
(2) Brightness Dialog

Press the [▲] or [▼] button to enter the Brightness Dialog.
Press the [1] button to exit the Brightness Dialog.
Press the [2] button to enter the Contrast Dialog.
(3) Analog/Digital Dialog

Press the [2] button to toggle between analog and digital modes.
B. When in Digital Input Mode

1. Main Menu
Press the [1] (Menu) button to enter the Main Menu:
Press the [▲] button to highlight the previous item or the [▼] button to highlight
the next item.
Press the [1] (Menu) button to exit the Main Menu.
(1) Auto Image Adjust Page:
Press the [2] button to execute the auto image adjust function.
(2) Contrast/Brightness Page:

1) Contrast Item
Press the [2] button to enter the brightness adjustment page.
2) Brightness Item

(3) Input Select Page:
Press the [2] button to switch to analog input mode.
(4) Audio Adjust Page:

Press the [▲] button to increase the volume.
Press the [▼] button to decrease the volume.
Press the [2] button to enable or disable mute function .
(4) Color Adjust Page:

Press the [2] button to enter the color adjustment page.
1) sRGB Item
2) 9300K Item
3) 6500K Item
4) 5400K Item
5) 5000K Item
Press the [2] button to select the currently highlighted item.
Press the [1] button to exit the currently highlighted item.
6) User Color Item
Press the [2] button to enter the user color page.
Red, Green, Blue Options:
Press the [2] button to cycle among the colors.
Press the [▲] button to increase the selected color level.
Press the [▼] button to decrease the selected color level.
(5) Information Page:

Press the [2] button to enter the information page.
Press the [1] button to exit the information page.
(6) Manual Image Adjust Page:

Press the [2] button to enter the manual image adjustment page.
1) Sharpness Item
Press the [2] button to enter the sharpness adjustment page.
Press “[▲]” Button to increase image sharpness.
Press “[▼]“ Button to decrease image sharpness.
(7) Setup Menu Page:

Press the [2] button to enter the setup menu page.

1) Language Select Item
Press the [2] button to enter the language selection page.
English, French… Option
Press the [2] button to select the language.
2) Resolution Notice Item

Press the [2] button to enter the resolution notice page.
3) OSD Position Item

Press the [2] button to enter the OSD position adjustment page.
a) Horizontal Position Option
Press the [▲] button to shift the menu to the right.
Press the [▼] button to shift the menu to the left.
b) Vertical Position Option:

Press the [2] button to enter the horizontal position adjustment page.
Press the [▲] button to shift the menu upward.
Press the [▼] button to shift the menu downward.
4) OSD Time Out Item

Press the [2] button to enter the OSD time out adjustment page.
Press the [▲] button to increase the OSD time out.
Press the [▼] button to decrease the OSD time out.
5) OSD Background Item

Press the [2] button to enter the OSD background selection page.

(8) Memory Recall Page
Press the [2] button to execute the memory recall function.
2. Other Menu:
This “shortcut” menu is directly accessible without bringing up the OSD.
(1) Contrast Dialog
Press the [▲] or [▼] button to enter the Contrast Dialog.
Press the [1] button to exit the Contrast Dialog.
Press the [2] button to enter the Brightness Dialog.
(2) Brightness Dialog
Press the [▲] or [▼] button to enter the Brightness Dialog.
Press the [1] button to exit the Brightness Dialog.
Press the [2] button to enter the Contrast Dialog.
(3) Analog/Digital Dialog

Press the [2] button to toggle between analog and digital modes.
C. Other Information
When the “No Signal” or “Out of Range” messages appear:
If no input signal is detected, the “No Signal” message will appear in the center of
the screen.
If the V-Sync signal rate is greater than than 85Hz or its resolution is greater than
SXGA, the “Out of Range” message will appear in the center of the screen.
Activating Factory Mode and Burn Mode:
While the device is in standby, press the [2] button, then press the power button to
enter Factory Mode. While Factory Mode is active, an additional menu page titled
“Factory Menu” will be accessible. Press the [2] button to enter the Factory Menu
page, then press the [2] button to enter Burn Mode.
When Installing a New Main Board

1. Enter Factory Mode.
2. Use a PC or chrom to send a 32-tone gray scale signal to the monitor.
3. Select “Auto Color”

Firmware update procedure :
When you received a received monitor , please check whether the firmware version. If not , please following procedure to
upgrade to the latest version .
1. Equipment needed :
- VP2030
- PC ( Personal computer )
- USB (A Male to B Male) cable
- Genesis firmware update board
- 9-Male to 9-Female serial cable
- VGA cable

2. Connection :
The 9-pin serial cable connects the com port of PC and the Genesis firmware update board. VP2030 and the Genesis
firmware update board is connected by VGA cable. The male A to male B USB cable connects the PC and Genesis
firmware update board.
Appendix A : How to install the software for ISP :

0. To setup ISP environment :
Hardware:
PC or notebook, 9-pin serial cable, VGA cable and USB cable (Male A to Male B). If your PC does not have serial
port, please get a USB to RS232 cable.
Software:
If the OS is Win2000 or WinXP , please install “GProbe”
In order to ensure can execute ISP program, please connect the USB to RS232 cable and set it as COM 1 in control panel if your
PC does not have COM port

0.1 Double-click the “ GProbe5.0.exe” in Windows & install the program. , see Fig 0.1
Fig 0.1
0.2 Keep on press “ Next “ 4 times to go through the installation processes, see Fig. 0.2
Fig. 0.2

0.3 Check the “I accept the agreement” then press “ Next “ , see Fig. 0.3
Fig. 0.3
0.4 Keep on press “ Next “ , see Fig. 0.4
Fig. 0.4

0.5 Keep on press “ Next “ , see Fig. 0.5
Fig. 0.5
0.6 Click “Next” to start the installation. See Fig 0.6
Fig. 0.6

0.7 If you see this message, click “Yes”. See Fig 0.7.
Fig. 0.7
0.8 If you see the Fig 0.8, click “Finich” button to restart the system.
Fig. 0.8
0.9 Installation is completed

Appendix B : How to use software to upgrade the BIOS :
1.1 After installation , we could find the shortcut in the setting path or the program bar ( default setting ) , see Fig 1.1
Fig. 1.1
1.2 Move your mouse cursor to GProbe 5 and click it. You will see the Fig. 1.2
Fig. 1.2

1.3 Please create a directory such as “ISP” below the root directory (the path is “drive letter”:\ISP now).
1.4 Copy the create a text file with the following string and save it as “ISP.txt”
SetBuffer 0x1000 4096

RAMWrite d:\GNSSISP\loader.hex
Run 0x500
RAMWrite d:\GNSSISP\isp8.hex
Run 0x580
FlashErase
FastFlashWrite d:\GNSSISP\rd_monitor.hex
1.5 Set the monitor to Factory Mode by pressing “2” and “Power” at the same time.
1.6 Click the right-lower terminal window and type “batch d(or other drive letter):\ISP\isp.txt” in the upper blank area then
click “Execute” button. See the Fig 1.3.
Fig. 1.3

1.7 After click the “Execute” button, you will see the terminal information in Fig. 1.4 . When the message “Batch: command
successful” is shown, the flash progress is completed.
Fig. 1.4

VP2030b-1 / VP2030b-1H series de-assembling procedure
1. Move the monitor our from carton 2. Put the monitor on desk & face down
3. Remove the VESA cover 4. Loose the screws & remove the stand
5. Separate the hook by tool (coin or screw-driver) 6. Remove the cover & AL-Foil &Mylar& Button/B CABLE

7. Loose the INVERTER SHIELDING SCREW 8. Tear off the yellow tape &Pull out the CCFL cables
9. Loose the INVERTER/B screw 10. Loose the SHIELDING SCREW
11. Tear off the yellow tape &Pull out the LVDS CABLE 12.Remove the shielding

15. Loose the bezel 16.Remove the Button/B
17. Loose the shield 18. Remove the PCBA & mylar
19. Loose the IO-NUT SCREW 20. Take out PCBA & remove the cables

19. Loose the BKT-T/B SCREW 20. Loose the BKT-R/L SCREW

VP2030b / VP2030bH Series packing method
1. Sticker on LCD protection film 2. Put the monitor into the PE or EPE bags
3. Put on the end-cap left / right 4. Put the monitor into carton
Face-up
5. Put all accessories into carton 6. Seal the monitor

handler
Power cable Users manual
VGA & DVI cable

6. Trouble Shooting Chart
6.1 Monitor Cann't Boot-up
Monitor Cann't Boot-

Up
NG Check Power Board

Change Power Board CN7 PIN 1,2
NG
Change Key Button Check Key Bottom
NG Check Crystal
Change Crystal X1
NG Check M/B
Change M/B 5V,3.3V.2.5V
1.8V
Change M/B

6.2 Black Screen
Black Screen
NG Check Panel Vcc

Change Power Board 5V
NG Check M/B Panel

Change Scalar M/B ON/OFF CN7
PIN 8 3.3V
Check M/B
NG CN7 PIN 7
Change Scalar M/B Brightness MAX
3.3V
Panel Break

6.3 No Signal
No Signal
NG Check VGA
Change VGA Card CARD
NG Check VGA
Change VGA Cable Cable
NG Check H/V Sync

Change Scalar M/B U22 PIN 14,15
Check CN5
Change Scalar M/B Pin Signal
Change Scalar M/B

6.4 No Signal In DVI-D
No Signal In DVI-D
NG Check VGA
Change VGA Card CARD
NG Check DVI-D
Change DVI Cable Cable
NG Check H/V Sync

Check CN5
Change Scalar M/B Pin Signal
Change Scalar M/B

6.5 No Signal In DVI_A
No Signal In DVI_A
Check VGA Card

Contact To VGA NG Support DVI-A
Card Seller Signal
NG Check DVI
Change DVI Cable Cable
NG Check H/V Sync

NG Check CN5
Change Scalar M/B Signal
Change Scalar M/B

6.6 U.S.B doesn't Work
U.S.B doesn't Work
NG Check USB M/B

Device Problem R20 5V
NG
Change Scalar M/B Check USB M/B
CN6 PIN1,2
NG
Check USB M/B
Change USB M/B U3 3.3V
NG Check USB M/B

Change USB M/B FUSE F1~F4
Short
Change USB M/B

6.7 OSD Pivot doesn't Work
OSD Pivot doesn't

Work
Solder R178 Both NG Check R178

Voltage 3.3V
Ends
NG When Pivot
Change Scalar M/B 0 or 90 Degree
Check R178
Voltege
Change Scalar M/B

7. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (VP2030b-1)

ViewSonic Model Number: VS10772
Serial No. Prefix: PSB Rev: 1d
Item Description ECR/ECN ViewSonic P/N Ref. P/N Location Universal number#
1 Accessories: Power Cord A-PC-0106-0224 DM333181G97 Power cable
2 POWER CORD SP-305+IS-14 3P 1.8M(TWN)B GP Added on 12/22/06 A-00003642 DM33T181004 power cord
3 POWER 3P 1.8M(CHN)Y546B300012180QD GP Added on 12/22/06 A-PC-0106-0306 DM333181S01 power cord
4 POWER CORD SP-023+IS-14 1.8M(B)EU GP Added on 12/22/06 A-PC-0106-0227 DM333181801 power cord
Board Assembly: 12/06/05: Update AS08B50000
5 Power Module (DTA)EADP-64BF B,90~264V GP B-00004348 Power board
Vendor P/N AS08B500000
6 L0VP M/B SPARE PART(GM1601,AU)FQ GP Added on 12/22/06 B-00008265 10L0VPMB000 Main board 38.16
12/06/05: Update 21LAVPMB003
7 Main Board Assy LAVP (GM1601-LF-CF) GP B-00004349 Main board
Vendor P/N 1SL0VPMB007
12/06/05: Update 23L0VPBB007
8 Button Board Assy L0VP GP B-00004350 Button board
Vendor P/N 1SL0VPBB001
12/06/05: Update 22L0VPUB005
9 USB Board Assy L0VP GP) B-00004351 USB board
Vendor P/N 1SL0VPUB001
10 Inverter Module B-00004352 AS023190407 Inverter board
Cabinets: 12/06/05: Update 24L0VPLB008
11 Front Bezel Assy L0VP LCD BEZEL SUB ASSY GP C-00004353 front bezel ass'y
Vendor P/N 34L0VPLB008
12 Back Cover Assy C-00004354 25L0VPLC005 back cover assy
13 Back Cover Assy Lovp Lcd Bezel Sub Assy VP2030b-H 03/14/06 Added C-00005378 35L0VPLC005 back cover assy
14 Stand Assy C-00004355 37LAVPSU003 Stand sub assy
15 Base Assy Replace VS Part # C-00004356 Base sub assy
38LAVPBS002
16 Pedestal on 12/22/06 PL-00008060
17 Stand Vesa Cover LAVP(EALAVP03,REV3A)GP 12/06/05: Added C-00004642 EALAVP03011 stand vesa cover
18 Cables: FFC Cable MB-BB CB-00004357 DEFC3609000 Cable MB-BB
19 CABLE MB-VGA (15/15P,1.8M)L7VD GP Added on 12/22/06 CB-00002602 DDL7VDPC005 VGA cable
20 CABLE DVI-D L0T BLACK 1.8 6.0 GP Added on 12/22/06 CB-00003440 DD0L0TTH108 DVI cable
21 Cable POWER-MB CB-00004358 DDLAVPPB104 Cable POWER-MB
22 Cable MB-LCD CB-00004359 DDL0VPLC004 Cable MB-LCD
23 VGA cable CB-00004360 DD0M7TPC005 VGA cable
VS-E060098/ Updated CB-00004361 DDWCVPDV019 DVI-I cable
24 DVI cable
and replaced on 12/11/06 CB-00003440 DD0L0TTH108
25 Documentation: User manual + CD wizard DC-00004362 HGL0VP01011 User manual
26 QC-PASS LABEL L7VC(HCL7V026,REV3A)GP Added on 12/22/06 DC-00003444 HCL7V026017
27 VSCN WARRANTY CARD W0VA(HDW0VA01,R3A) GP Added on 12/22/06 DC-00005215 HDW0VA01011
28 ADDRESS LABEL L7VC(HCL7V024,REV3B) Added on 12/22/06 DC-00003443 HCL7V024014
29 Electronic 20" AUO TFT LCD panel E-00004363 AAM201UN029 LCD panel
Components: VS-E060426/ Added on
30 AUO Panel M201UN02 V.6 2nd Source E-00008259 AAM201UN037
12/13/06
VS-E060319 / Added on
31 Integrated Circuit E-00008135 AKD37W+TW06 U13
10/30/06
32 Hardware: Screw M3.0*5.0-B BLACK HW-00004364 MM30050BJ21 Screw
SCREW M4.0*8-B (NI, NYLOK) M-SCW-0824-0795 MM40080BCI5 Screw
12/22/06: Removed &
33 M-SCW-0824-6761 panel to L/F BKT
SCREW M3.0*3.0-I Replaced Part MM30030IBJ4
HW-00008069
34 IO NUT LI1(MBLI1004,REV3A)GP 12/06/05: Added M-MS-0808-8986 MBLI1004018 DVI,D-SUB
35 Miscellaneous: LCD film M-00004365 JXL0VP01018 LCD FILM
36 WARRANTY STICKER L7VC(HCL7V023,R3A)GP Added on 12/22/06 M-00003446 HCL7V023018 WARRANTY STICKER
37 Packing Material: PE bags P-00004159 HAL0T002019 PE bags
38 PE BAG L0T(HAL0T002,REV3A)GP Added on 12/22/06 P-00008271 HAL0VP04015 PE bag
39 Inner Carton VP2030b-H(carton-s Lovp(HFL0VP04,Rev3A) 03/14/06 Added P-00005379 HFL0VP04010 carton
40 Outer Carton VP2030b-H(carton-s Lovp(HFL0VP05,Rev3A) 03/14/06 Added P-00005380 HFL0VP05016 carton
41 Foam- End cap Left VP2030b-H 03/14/06 Added P-00005381 HBL0VP03010 cushion
42 Foam - End Cap Right VP2030b-H 03/14/06 Added P-00005382 HBL0VP04016 cushion
43 Carton P-00004366 HFL0VP01011 carton
VS-E060480/ Added on
44 Carton P-00008255 HFL0VP03013
12/13/06
12/06/05: Update HBLAVP01017
45 END CAP(L) L0VP(HBL0VP01,REV3A)GP P-00004367 cushion
Vendor P/N HBL0VP01017
12/06/05: Update HBLAVP02013
46 END CAP(R) L0VP(HBL0VP02,REV3A)GP P-00004368 cushion
Vendor P/N HBL0VP02013
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This
is to eliminate repeated cross checks of each item between this version and prior versions.

BOM LIST ( VP2030b-1 )
Rev: 1b
Item Viewsonic P/N Ref. P/N Description Location Universal No. Qty
1 N/A 1L0VPZXVS07 L0VP LCD MONITOR(USA,VP2030) GP
2 B-00004349 21LAVPMB003 LAVP M/B ASSY(GM1601-LF-CF) GP 1
3 N/A 31LAVPSS009 LAVP M/B S/S ASSY(GM1601-LF-CF) GP 1
C5,C6,C28,C29,C44,C46,C47,
4 N/A CC647T1MD05 CAP EC 47U 10V(+-20%,105C,5*11,2000H)GP C59,C62,C64,C76,C77,C96,C 21
100,C103,C107,C119,C126,C1
5 N/A CC71004MD09 CAP ELEC DIP 100U 25V(+-20%,105C,6*7) GP C124 1
6 N/A CC73303MD69 CAP ELEC DIP 330U 16V(+-20%,105C,8*9) GP C174,C204,C205 3
7 N/A CC810T1MD13 CAP EC 1000U6.3V(+-20%,105C,8*15,2KH)GP C206 1
8 N/A CC710T3MD04 CAP EC 100U 16V +-20%,105C,6.3*5,1000 GP C180,C181,C184,C185,C187,C188 6
9 N/A DC11050K007 CHOKE COIL 100UH(5A,+-10%,HKH050-101K)GP L28 1
10 N/A DHR31110002 ROLL BALL SWITCH 4P RBS311100 GP U19 1
11 N/A BG614318072 XTAL DIP 14.318MHZ(+-30PPM,49/US) GP X1 1
12 N/A DFDI30FR103 CONN DVI-I DIP30P 3R FR(P1.905,H10.04)GP CN2 1
13 N/A DFDS15FR076 CONN D-SUB 15P 3R FR(P1.15,H12.55) GP CN1 1
14 N/A DFHD30MR267 CONN DIP HEADER 30P 2R MR(P2.0,H4.0) GP CN5 1
15 N/A DFHD04FR007 CONN DIP HEADER 4P 2R FR(P2.5,H5) GP CN6 1
16 N/A DFHD08MR319 CONN DIP HEADER 8P 1R MR(P2.0,H4.1) GP CN7 1
17 B-00004350 23L0VPBB007 L0VP BUTTON/B ASSY GP 1
18 N/A DAL0VPTB011 PCB(BUTTON) L0VP TB(2L,111*13,REVA) GP 1
19 N/A DHPTMG53311 SWITCH PU-BUTTON TMG-533-T/R(160+-50G)GP SW1,SW2,SW3,SW4,SW5 5
20 N/A DFFC11FR001 CONN SMD FFC 11P 1R FR(P 1,H1.55) GP CN1 1
21 N/A BEYG0003ZA5 LED(SMD) Y/G(KPB-3025NSGC-F01) GP LED1 1
22 B-00004348 AS08B500000 PWR MODULE(DTA)EADP-64BF B,90~264V GP 1
23 B-00004351 22L0VPUB005 L0VP USB/B ASSY(GP) 1
24 N/A 32L0VPSS007 L0VP USB/B S/S ASSY(GP) 1
25 N/A CC71004MD09 CAP ELEC DIP 100U 25V(+-20%,105C,6*7) GP C1,C7,C13,C16,C26,C27 6
26 N/A DFUB08MR009 CONN DIP USB A-T D-8P 2R MR(P2,H15.35)GP J1,J2 2
27 N/A DFUB04MR001 CONN DIP USB B-T 4P 2R MR(P2.5,H11.3) GP USB1 1
28 N/A BG612000202 XTAL DIP 12MHZ(+-30PPM,HC-49/S TYPE) GP X1 1
29 N/A DFHD04MR001 CONN DIP HEADER 4P 2R MR(P2.54,H5) GP CN1 1
30 C-00004353 24L0VPLB008 L0VP LCD BEZEL ASSY GP 1
31 C-00004353 34L0VPLB008 L0VP LCD BEZEL SUB ASSY GP 1
32 CB-00004357 DEFC3609000 FFC CABLE MB-BUTTOM(11P,360MM)LAVP GP 1
33 CB-00004358 DDLAVPPB104 CABLE POWER-MB(8P,55MM)LAVP GP 1
34 CB-00004359 DDL0VPLC004 CABLE MB-LCD(30P,100MM,AU)L0VP GP 1
35 N/A FALAVP01019 PCB SHIELD LAVP(FALAVP01,REV3A)GP 1
36 N/A FALAVP02015 INVER SHIELD LAVP(FALAVP02,REV3A)GP 1
37 N/A FAL0VP01016 LCD BRACKET-R L0VP(FAL0VP01,REV3A)GP 1
38 N/A FAL0VP02012 LCD BRACKET-L L0VP(FAL0VP02,REV3A)GP 1
39 N/A FALAVP05014 LCD BAK BOTTOM LAVP((FALAVP05,REV3A)GP 1
40 N/A FCLAVP01011 INVERTER MYLAR LAVP(FCLAVP01,REV3A)GP 1
41 HW-00004364 MM30050BJ21 SCREW M3.0*5.0-B BLACK GP 25
42 N/A FALAVP08013 LCD BRACKET TOP LAVP(FALAVP080,R3A) GP 1
43 N/A MBL9V001019 IO NUT L9VDA-5(MBL9V001,REV3A)M3*15*6 GP 4
44 N/A FCLAVP02017 AL FOIL LAVP(FCLAVP02,REV3A)210*10 GP 1
45 N/A FCLAVP03013 AL FOIL LAVP(FCLAVP03,REV3A)65*30 GP 3
46 N/A FCW0E002016 POWER MYLAR W0E-A1(FAW0E002, REV3A)GP 1
47 N/A FCLAVP04010 POWER MYLAR TOP LAVP(FCLAVP04,R3A) GP 1
48 N/A FCLAVP05016 SHIELD MYLAR LAVP(FCLAVP05,R3A) GP 1
49 N/A FCLAVP06012 BUTTON/B MYLAR LAVP(FCLAVP06,R3A) GP 1
50 N/A FCLAVP07019 BUTTON EVA LAVP(FCLAVP07,REV3A) GP 1
51 M-MS-0808-8984 FCL70004010 LCD MYLAR L70L-E(FCL70004,REV3A)GP 1
52 C-00004354 25L0VPLC005 L0VP LCD COVER ASSY GP 1
53 C-00005378 35L0VPLC005 L0VP LCD COVER SUB ASSY GP 1
54 N/A EAL0VP02012 LCD COVER L0VP(EAL0VP02,REV3A)GP 1
55 M-MS-0808-9411 FBL70008014 LOCK METAL L70B(FBL70008,REV3A) GP 1
56 N/A EBWCVP02011 VSC ELLIP LOGO POLISH(EBWCVP02,REV3A) GP 1
57 N/A 26LAVPSA009 LAVP STAND ASSY GP 1
58 C-00004355 37LAVPSU003 LAVP STAND SUB ASSY GP 1
59 N/A FALAVP07017 HINGE ASSY LAVP(FALAVP07,REV3A)GP 1
60 N/A EALAVP04018 STAND TOP LAVP((EALAVP04,REV3A)GP 1
61 N/A EALAVP05014 STAND BOTTOM LAVP((EALAVP05,REV3A)GP 1
62 N/A EALAVP06011 HINGE COVER FRONT LAVP(EALAVP06,REV3A)GP 1
63 N/A EALAVP07017 HINGE COVER BACK LAVP((EALAVP07,REV3A)GP 1
64 N/A EBLAVP02016 CLAMP LAVP(EBLAVP02,REV3A)GP 3
65 M-SCW-0824-0725MF30050IBJ6 SCREW F3*5-I(NI)GP 9
66 PL-00008060 38LAVPBS002 LAVP BASE SUB ASSY GP 1
67 N/A EALAVP08013 BASE LAVP (EALAVP08,REV3A)GP 1
68 N/A FALAVP06011 BASE PLATE LAVP(FALAVP06,REV3A)GP 1
69 N/A GALAVP01019 RUBBER FOOT LAVP D24*4 GALAVP01,REV3A GP 4
70 M-SCW-0824-0725MF30050IBJ6 SCREW F3*5-I(NI)GP 6
71 M-SCW-0824-0795MM40080BCI5 SCREW M4.0*8-B(NI,NYLOK)GP 8

72 N/A 27LAVPCS007 LAVP CHASSIS ASSY GP 1
73 C-00004642 EALAVP03011 STAND VISA COVER LAVP(EALAVP03,REV3A)GP 1
74 M-SCW-0824-0814MM30060BBJ3 SCREW M3.0*6,B(NI) GP 4
75 N/A 2AL0VPPTA03 L0VP PANEL DEPENDENT KIT ASSY(AU) GP 1
76 E-00004363 AAM201UN029 LCD(TFT) 20"M201UN02 V.5(LF/8MS) GP 1
77 E-00008259 AAM201UN037 LCD(TFT) 20"M201UN02 V.6(LF/8MS) GP (2nd panel source) 1
78 N/A AZL0VP0A001 L0VP SW BIOS IMAGE(AU)GM1601-LF-CF N/A 1
79 B-00004352 AS023190407 INV MODULE(SEL)LAVP(20V,V=900V,MAX)GP 1
80 N/A 28L0VPPK001 L0VP PACKING ASSY GP 1
81 CB-00004360 DD0M7TPC005 CABLE ASSY M7T MB-VGA(15/15P,REV1A) GP 1
82 CB-00004361 DDWCVPDV019CABLE DVI-I(29/29P,1.8M)WCVP GP 1
83 P-00004367 HBL0VP01017 END CAP(L) L0VP(HBL0VP01,REV3A)GP 1
84 P-00004368 HBL0VP02013 END CAP(R) L0VP(HBL0VP02,REV3A)GP 1
85 M-LB-0813-0747 HCL7V004013 CORE LABEL(HCL7V004,REV3A) 1
86 N/A HCL0VP01018 ID LABEL L0VP(HCL0VP01,REV3A)GP 1
87 M-LB-0813-0745 HCL7V002011 SERIAL LEBAL L7V(HCL7V002,REV3A) GP 1
88 M-LB-0813-1042 HCL7V019011 CARTON LABEL L7VC(HCL7V019,REV3B) GP 1
89 P-00004366 HFL0VP01011 CARTON L0VP(HFL0VP01,REV3A)GP 1
90 DC-00004362 HGL0VP01011 CD+QSG L0VP(HGL0VP01,REV3A)GP 1
91 PL-00005198 JXLM5003011 HANDLE LM5S(JXLM5003,REV 3B) GP 1
92 M-00004365 JXL0VP01018 LCD FILM L0VP(JXL0VP01,REV3A)GP 1
93 M-LB-0813-1043 HCL70021011 HI-POT LABEL L70L(HCL70021,REV3A) 1
94 N/A HFL0VP02017 SPACE PLATE L0VP(HFL0VP02,REV3A)GP 0.083
95 P-00004159 HAL0T002019 PE BAG L0T(HAL0T002,REV3A)GP 1
96 N/A HDL7VC01019 SERVICR PAPER L7VC(HDL7VC01,REV3A) GP 1
97 DC-00003536 HCL9V009011 HG LABEL L9VD(HCL9V009,REV3A) 1
98 A-PC-0106-0224 DM333181G97 POWER CORD 3P 1.8M(USA)V04VS350012180 GP 1

8. Exploded View And Wxploded Parts List

Cable connection diagram
33 34 PANEL LVDS
CN2 CN1 CN4 CN5

CN1 CN2
CN3
To panel
Main board CN3
Inv./B Power board
CN5
USB board
CN6 CN1
CN4
Button board CN1 32 FFC cable

EXPLODED PARTS LIST ( VP2030b-1)
Rev: 1b
Item Viewsonic P/N PART No. DESCRIPTION Q'ty
1 C-00004353 34L0VPLB008 L0VP BEZEL SUB ASSY 1
2 N/A EAL0VP01016 LCD BEZEL L0VP 1
3 N/A ECL0VP01011 CONTROL BUTTON LAVP 1
4 N/A EBLAVP01010 LED LENS LAVP 1
5 N/A FALAVP01019 PCB SHILED LAVP 1
6 N/A FALAVP02015 INVER SHIELD LAVP 1
7 N/A FAL0VP01016 LCD BRACKET-R 1
8 N/A FAL0VP012012 LCD BRACKET-L 1
9 N/A FALAVP05014 LCD BRACKET BOTTOM LAVP 1
10 N/A FCLAVP01011 TNVERTER MYLAR LAVP 1
11 M-SCW-0824-0728 MM30050IBJ3 SCREW M3.0*5.0-I(NI) 25
12 C-00004422 25LAVPLC008 LAVP LCD COVER ASSY 1
13 N/A EALAVP02015 LCD COVER LAVP 1
14 C-00004642 EALAVP03011 STAND VESA COVER LAVP 1
15 N/A FBL7000B014 LOCK METAL L70B 1
16 M-SCW-0824-0814 MM30060BBJ3 SCREW M3*6-B (NI) 4
17 N/A 26LAVPSA009 LAVP STAND ASSY 1
18 N/A FALAVP07017 HINGE ASSY LAVP 1
19 N/A EALAVP04018 STAND TOP LAVP 1
20 N/A EALAVP05014 STAND BOTTOM LAVP 1
21 N/A EALAVP06011 HINGE COVER FRONT 1
22 N/A EALAVP07017 HINGE COBER BACK LAVP 1
23 N/A EBLAVP02016 CLAMP LAVP 3
24 M-SCW-0824-0795 MM40080BCI5 SCREW M4.0*8-B(NI, NYLOK) 8
25 M-SCW-0824-0725 MF30050IBJ6 SCREW F3*5-I(NI) 15
26 N/A EALAVP09013 BASE LAVP 1
27 N/A FALAVP06011 BASE PLATE LAVP 1
28 N/A GALAVP01019 RUBBER FOOT LAVP 4
29 M-MS-0808-8986 MBLI1004018 IO NUT 4
30 N/A FALAVP08013 LCD BRACKET TOP 1
31 N/A MS30030I934 SCREW 3*3.0-I 4
32 CB-00004357 DEFC3609000 FFC CABLE MB-BUTTON 1
33 CB-00004358 DDLAVPPB104 CABLE POWER-MB 1
34 CB-00004359 DDL0VPLC004 CABLE MB-LCD 1
35 E-00004363 AAM201UN029 LCD(TFT) 20"M201UN02 V.5 1
35 E-00008259 AAM201UN037 LCD(TFT) 20"M201UN02 V.6 (2nd panel 1
36 B-00004352 AS023190407 INV MODULE 1
37 B-00004348 AS08B500000 PWR MODULE(DTA)EADP-64BF 1
38 B-00004349 21LAVPMB003 M/B ASSY(GM1601-LF-CF) GP 1
39 B-00004351 22L0VPUB005 USB/B ASSY(GP) 1

PACKING PART LIST ( VP2130b-1 )
ViewSonic Model Number: VS10773-1W
Rev: 1b
Serial No. Prefix: PSD
Item ViewSonic P/N Ref. P/N Description Q'ty
1 CB-00004361 DDWCVPDV019 DVI cable 1
2 A-PC-0106-0224 DM333181G97 POWER CORD 3P 1.8M 1
3 CB-00004360 DD0M7TPC005 VGA CABLE 1
4 P-00004159 HAL0T002019 PE bag 1
5 P-00004429 HBLAVP01010 END CAP -L 1
6 #N/A HBLAVP01016 END CAP R 1
7 M-LB-0813-0747 HCL7V004013 Core label 1
8 #N/A HCLAVP01011 ID label 1
9 M-LB-0813-0745 HCL7V002011 S/N label 1
10 M-LB-0813-1042 HCL7V019011 Carton label 1
11 P-00004428 HFLAVP01013 Carton 1
12 DC-00004425 HGLAVP01014 CD+QSG 1
13 #N/A JXLM5003011 Handle 1
14 M-00004427 JXLAVP01011 LCD film 1
15 #N/A HFL0VP02017 Space Plate 1

+3.3V +2.5V +1.8V
LVDS+,LVDS-
VS
HS
Triple ADC PANEL AC IN 110V~264V
Analog R +12V
G 20,21,23
RGB Interface CLK+
B DC OUT +20V
BACKLIGHT
CLK-
BACKLIGHT
+3.3V
SCL
SDA
SCL
SDA
74HCT4053 RESET
9. Block Dragram
+5V
Viewsonic Corporation
RX
TX +3.3V
+5V
+5V
FSDATA,FSADDR
SCL
GM1601
24LC02 SDA K4D263238G-VC33
74HCT4053 74HCT4053 FSCLK+
+5V
FSCLK-
+5V
+3.3V
24LC02
RX0- ~RX2-
BRIGHTNESS
DSCL
DSDA
ASCL
ASDA
RX0+ ~RX2+ OCMADDR,OCMDATA
PANEL ON/OFF
DVI_R
67
DVI SST39VF040
DVI_G
DVI DVI_B Interface
RXC+
RXC-
HS VS
HS
VS
74HCT4053 POWER BLOCK
+5V +3.3V
AIC1084
+12V AIC1577 ADJ
+5V
+2.5V
LT1117
Confidential - Do Not Copy

KEYPAD +1.8V
AIC1084
VP2030b-1
CN1 CN2
D_SUB DVI_I
PIN1 PIN2
Viewsonic Corporation
CN6
PIN3 PIN4
10. Schematic Diagrams
GM1601M/B BLOCK
U21
GM1601H_CF U13
PIN1 DDR
68
CN3
KEYPAD
U11
FLASH
POWER
3 4
Confidential - Do Not Copy

U19
1 2
PIN2 PIN1
CN10 CN7
VP2030b-1
LVDS POWER_IN
BK2125HS102/8
1 2
VGA_5V +5V
3 L19
+5V
47uF/6.3V
L27
C1
C2
0.1u C3
0.1u C4
C17
R4
R5
R6
R7
R8
R9
R15
R16
R25
0.1u
0.1u
C5
R186
BK2125HS102/8
R12
U2 24AA02 100K(NC)
0.1u
1 8 R23
A0 VCC 100R CN1
10K
10K
2 7
3.3K
3.3K
3.3K
4.7K
4.7K
4.7K
A1 WP VGASCL
10K
3 6 15 5
10K(NC)
A2 SCL R24 0R C189 22u
4 GND SDA 5 10 VGA_CAB 5
VGA_VS 14 4 U1 AD8186
9 DVI_BLUE+ C9 0.1u 1 24 R14
VGA_HS VGA_5V IN0A VCC
R30 13 3 VGA_BLUE+ 2 23 0R
VGA_SCL 100R DVI_GREEN+ C11 0.1u DGND OE A/D_SEL
8 3 IN1A SEL A/B 22 A/D_SEL 5
VGA_SDA VGASDA 12 2 VGA_GREEN+ 4 21
C190 22u VREF VCC
7 5 IN2A OUT 0 20 BLUE 5
11 1 VGA_RED+ C191 22u 6 19
DVI_RED+ C14 0.1u VCC VEE
R208
R209
6 7 VEE OUT 1 18 GREEN 5
VGA_RED+ C13 0.1u 8 17
R26
R31
R32
IN2B VCC SOG 5
DB15 HD C192 22u 9 16
VEE OUT 2 RED 5
VGA_GREEN+ C18 0.1u 10 15
75R/NC R17
75R/NC R18
75R/NC R19
IN1B VEE
11 VEE DVCC 14
C193 22u
10K
10K
12 13
R20
R21
R22
IN0B VCC
75R
75R
75R
VGA_BLUE+ C20 0.1u
3.3K
3.3K
3.3K
C194 22u L31 L33 L34
+5V +5V +5V +5V +5V +5V +5V
C6
C7
C8
R27
R28
R29
BK2125HS102/8/NC
BK2125HS102/8/NC
BK2125HS102/8/NC
1
1
D23 D24 D9 D10 D1 D2 D3
DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC
0.1u
4.7K
4.7K
4.7K
0.01u
47uF/6.3V
3 VGA_HS 3 VGA_VS 3 VGASCL 3 VGASDA 3 VGA_BLUE+ 3 VGA_GREEN+ 3 VGA_RED+ L21 L22 L24
BK2125HS102/8
BK2125HS102/8
BK2125HS102/8
2
2
DVI_BLUE+ R1 0R(NC) BLUE
VGA_BLUE+ R10 0R(NC)

DDCD_5V +5V
R33
R34
DVI_GREEN+ R2 0R(NC) GREEN
16
U3
DVI_SCL R184 0R(NC) DSCL 1 2 12 RXD VGA_GREEN+ R11 0R(NC)
DVI_5V +5V RXD 5
VCC
VGA_SCL R35 22R X0 DDC_SCL
3 14 X X1 13 DDC_SCL 5
DVI_SDA R185 0R(NC) DSDA VGA_SDA R36 22R
10K
10K
15 Y
DDCD_5V ASCL 2 TXD VGA_RED+ R13 0R(NC) RED
ASDA Y0 DDC_SDA TXD 5
CN2 4 1
C23
Z Y1 DDC_SDA 5 DVI_RED+
U4 R3 0R(NC)
R39
R40
C22
25 1 A0 VCC 8 Z0 5
1 RX2- 0.1u
2 7 3
C24
RX2- RX2+ RX2- 5 A1 WP Z1
Swap Pin 2 & Pin12
0.1u
RX2+ 2 RX2+ 5 3 A2 SCL 6
3 4 5 6
16
GND U5 GND SDA INH

10K
10K
0.1u
RX4- 4 7 VEE A 11
5 12 DSCL 24AA02 10
VCC
RX4+ DVISCL R44 100R DVI_SCL X0 ASCL B R43 0R

SCL 6 14 X X1 13 8 GND C 9 DEBUG 5
7 DVISDA R45 100R DVI_SDA 15
SDA DVI_VS Y DSDA DDCD_5V 74HCT4053 R47
VS 8 Y0 2
R210 10K 4 1 ASDA
R49
R50
RX1- Z Y1
RX1- 9 RX1- 5
10 RX1+ 5 VGA_SCL R37 0R(NC) DDC_SCL
RX1+ RX1+ 5 Z0
11 3 100K
GND DVI_5V Z1 VGA_SDA R38 0R(NC) DDC_SDA
RX3- 12
10K
10K
13 6
DVI CONNECTOR
RX3+ INH DSCL +3.3V

14 R51 10K 7 11 R55 R52 22R
14
14
5V DVI_CAB 5 VEE A DSDA DSCL_1 5
15 10 0R R53 22R
GND B DSDA_1 5
16 R54 10K 8 9 U6
HP GND C +5V HS R58 20R
1 A0 VCC 8 1 2 3 4 AHS 5
17 RX0- R56 74HCT4053 2 7 C26
C25
RX0- RX0+ RX0- 5 A1 WP
18 R57 3 6 0.1u R60 C213 U7A U7B
RX0+ RX0+ 5 A2 SCL
19 100K 4 5 74LCX14MX/NC 74LCX14MX/NC
GND GND SDA
0.1u
20
7
RX5- 100K 24AA02 33P
21
16
RX5+ U22 510R +3.3V
GND 22
23 RXC+ VGA_HS R211 0R VGA_HS_C 12 R182 0R
C27
RXC+ 5
VCC
RXC+ RXC- DVI_HS R212 0R DVI_HS_C X0
RXC- 24 RXC- 5 13 X1 X 14
Y 15
C1 DVI_RED+ VGA_VS R213 0R VGA_VS_C 2
RED DVI_GREEN+ +5V +5V DVI_VS R214 0R DVI_VS_C Y0
0.1u
GRN C2 +5V EDID_SEL 5 1 Y1 Z 4
C3 DVI_BLUE+
BLU DVI_HS
C195
C196
C197
C198
C4 5
R64
R63
R62
HS Z0 +3.3V
1
C5 D6 D7 D8 3
14
14
GND DAN217K/NC DAN217K/NC DAN217K/NC Z1
R215
26
6
22p/NC
22p/NC
22p/NC
22p/NC
INH
3 DVI_GREEN+ 3 DVI_BLUE+ 3 DVI_RED+ 11 A VEE 7 VS R61 20R 5 6 9 8 AVS 5
10
75R
75R
75R
B
DVI-I 9 C GND 8 R65
C212
U7C
74LCX14MX/NC
U7D
74LCX14MX/NC
10K
74HCT4053
7
33P
2
R59 R187 510R

A/D_SEL 0R 100K R183 0R
+5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V
VGA_HS R41 0R(NC) HS
ViewSonic Corporation
1
D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 DVI_HS R46 0R(NC)
DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC DAN217K/NC
3 DVISDA 3 DVISCL 3 DVI_HS 3 DVI_VS 3 RXC+ 3 RXC- 3 RX2+ 3 RX2- 3 RX1+ 3 RX1- 3 RX0+ 3 RX0- VGA_VS
DVI_VS
R42
R48
0R(NC)
0R(NC)
VS
Model INPUT
Title
2
Date Rev:

L1 +1.8V_CORE L2 +3.3V_LVDS
+1.8V +1.8V_CORE +3.3V +3.3V_LVDS
CX000800000 CX000800000
C28
C29
C44
C30
C31
C32
C33
C34
C35
C36
C37
C38
C39
C40
C41
C42
C43
C45
FSDATAU3 FSDATA[0..31] 6
RN1 8 1 33R FSDATA11
FSDATAU2 FSDATA10
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
7 2
47uF/6.3V
47uF/6.3V
47uF/6.3V
FSDATAU1 6 3 FSDATA9
FSDATAU0 FSDATA8
+3.3V_LBADC
+1.8V_CORE
+1.8V_CORE
+3.3V_DIG
+3.3V_LBADC
FS_2.5
+3.3V_LVDS
FSVREF1
+1.8V_DVI
+3.3V_DVI
+1.8V_ADC
+3.3V_ADC
+3.3V_PLL
+3.3V_DIG
FS_2.5
+3.3V_PLL
AD12 +3.3V_LVDSB
+3.3V_LVDSA
+3.3V_LVDS
FSVREF1
5 4
+1.8V_ADC
+3.3V_ADC
+1.8V_DVI
+3.3V_DVI
AD13 +3.3V_LVDSB
+3.3V_LVDSA
FSDATAU31 RN2 8 1 33R FSDATA24
FSDATAU[0..31]
L3 +3.3V_DIG L4 FSVREF1
+3.3V +3.3V_DIG FSVREF FSVREF1 FSDATAU5
CX000800000 CX000800000 RN3 1 33R FSDATA13
AC10
AC12
AD20
AC22
AC21
AA23
AB23
AE17
8
C46
C47
C59
W23
W25
AC4
AC6
AC8
M23
AA4
AB4
U17
U11
U16
U10
D17
D23
D22
C13
H23
R23
D10
C11
C10
K17
K10
K16
K11
K23
P23
V23
E23
T16
T17
T11
F23
L16
L11
L23
J23
J24
FSDATAU4 FSDATA12
W4
G1
7 2
C48
C49
C50
C51
C52
C53
C54
C55
C56
C57
C58
C60
C61
D6
D8
D9
C9
C8
C6
D3
H3
H1
Y4
A3
A4
A2
B3
E3
F4
F2
J3
J1
U21 FSDQMU0 6 3 FSDQM1
FSDQSU0 FSDQS1 FSDQM1 6
5 4 FSDQS1 6
FSVREF
FSVREF
IO_3.3
IO_3.3
IO_3.3
IO_3.3
IO_3.3
IO_3.3
IO_3.3
IO_3.3
IO_3.3
IO_3.3
IO_3.3
LBACD-33
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
FS_2.5
LVDSB_3.3
LVDSB_3.3
LVDSB_3.3
LVDSA_3.3
LVDSA_3.3
LVDSA_3.3
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
CORE_1.8
VDDA18_DLL
DVI_1.8
DVI_1.8
DVI_1.8
DVI_1.8
DVI_3.3
DVI_3.3
DVI_3.3
DVI_3.3
DVI_3.3
ADC_1.8
ADC_1.8
ADC_3.3
ADC_3.3
ADC_3.3
ADC_3.3
VDDA33_RPLL
VDDA33_PLL
VDDA33_FPLL
VDDD33_LVDS
VDDA33_SDDS
VDDA33_SDDS
VDDA33_DDDS
VDDA33_DDDS
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
47uF/6.3V
47uF/6.3V
47uF/6.3V
FSDATAU14 RN4 8 1 33R FSDATA1
E24 FSDATAU0 FSDATAU15 7 2 FSDATA0
FSDATA0 FSDATAU1 FSDATAU7 FSDATA15
FSDATA1 E25 6 3
N4 E26 FSDATAU2 FSDATAU6 5 4 FSDATA14
4 DSCL_1 DVI_SCL FSDATA2 FSDATAU3
4 DSDA_1 N3 DVI_SDA FSDATA3 F24
A8 G23 FSDATAU4 FSDQSU1 RN5 8 1 33R FSDQS0
4 RX0+ RX0+ FSDATA4 FSDATAU5 FSDQMU1 FSDQM0 FSDQS0 6
4 RX0- B8 RX0- FSDATA5 G24 7 2 FSDQM0 6
L5 +3.3V_LBADC L6 +3.3V_DVI A9 G25 FSDATAU6 FSDATAU12 6 3 FSDATA3
+3.3V +3.3V_LBADC +3.3V +3.3V_DVI 4 RX1+ RX1+ FSDATA6 FSDATAU7 FSDATAU13 FSDATA2
CX000800000 CX000800000 B9 G26 5 4
C62
C64
4 RX1- RX1- FSDATA7 FSDATAU8
A10 R24
C63
C65
C66
C67
C68
C69
4 RX2+ RX2+ FSDATA8 FSDATAU9
4 RX2- B10 RX2- FSDATA9 P26 FSDATAU18 RN6 8 1 33R FSDATA18
A6 P25 FSDATAU10 FSDATAU19 7 2 FSDATA19
4 RXC+ RXC+ FSDATA10 FSDATAU11 FSDQMU2 FSDQM2
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
B6 P24 6 3
47uF/6.3V
47uF/6.3V
4 RXC- RXC- FSDATA11 FSDATAU12 FSDQSU2 FSDQS2 FSDQM2 6
D5 NO_CONNECT FSDATA12 N24 5 4 FSDQS2 6
C5 N23 FSDATAU13
+3.3V_DVI R66 249R NO_CONNECT FSDATA13 FSDATAU14 FSDATAU8 RN7
+3.3V_DVI B11 REXT FSDATA14 M26 8 1 33R FSDATA7
1% M25 FSDATAU15 FSDATAU9 7 2 FSDATA6
FSDATA15 FSDATAU16 FSDATAU10 FSDATA5
FSDATA16 R25 6 3
R67 100R C70 0.01u B1 R26 FSDATAU17 FSDATAU11 5 4 FSDATA4
R68 100R C71 0.01u BLUE- FSDATA17 FSDATAU18
4 BLUE B2 BLUE+ FSDATA18 T24
L7 FS_2.5 R69 100R C72 0.01u C1 T25 FSDATAU19 FSDATAU20 RN8 8 1 33R FSDATA20
+2.5V FS_2.5 GREEN- FSDATA19 FSDATAU20 FSDATAU21 FSDATA21
CX000800000 R70 100R C73 0.01u C2 U26 7 2
C76
C77
4 GREEN GREEN+ FSDATA20 FSDATAU21 FSDATAU22 FSDATA22
R71 100R C74 0.01u D1 V24 6 3
C78
C79
C80
C81
C82
C83
C84
C85
C86
C87
C88
C89
C90
C91
C92
R72 100R C75 0.01u RED- FSDATA21 FSDATAU22 FSDATAU23 FSDATA23
4 RED D2 RED+ FSDATA22 V25 5 4
R73 470R C93 0.01u C3 V26 FSDATAU23
4 SOG SOG FSDATA23 FSDATAU24 FSDQSU3 RN14 8 1 33R FSDQS3
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
A1 M24
47uF/6.3V
47uF/6.3V
NO_CONNECT FSDATA24 FSDATAU25 FSDQM3 FSDQS3 6

+3.3V_PLL +3.3V_PLL R74 0R N2 L26 FSDQMU3 7 2
4 DDC_SCL VGA_SCL FSDATA25 FSDATAU26 FSDATAU27 FSDATA28 FSDQM3 6
R75 0R N1 L25 6 3
+3.3V_PLL +3.3V_PLL 4 DDC_SDA VGA_SDA FSDATA26 FSDATAU27 FSDATAU26 FSDATA29
R76 0R L4 L24 5 4
4 AHS AHSYNC FSDATA27 FSDATAU28
R77 0R L3 J25
4 AVS AVSYNC FSDATA28 FSDATAU29 FSDATAU25
C94 C95 R78 10K R4 EXTCLK FSDATA29 H26 RN19 8 1 33R FSDATA30
H25 FSDATAU30 FSDATAU24 7 2 FSDATA31
5p X1 5p FSDATA30 FSDATAU31 FSDATAU16 FSDATA16
FSDATA31 H24 6 3
L8 +3.3V_LVDSB L9 +1.8V_ADC G4 FSDATAU17 5 4 FSDATA17
+3.3V +3.3V_LVDSB +1.8V +1.8V_ADC XTAL
CX000800000 CX000800000 T23 /FSWEU
C100
G3
C96
TCLK /FSALTWE
14.318MHz Y23 /FSCASU
0.1u C101
0.1u C102
F1
C97
C98
C99
NO_CONNECT /FSALTCAS
K3 NO_CONNECT /FSALTRAS AC23/FSRASU
R79 3.3K K2 ACS_RSET_HD FSADDRU[0..11]
0.1u
0.1u
0.1u
47uF/6.3V
47uF/6.3V
Y20 FSADDR[0..11] 6
C19 VRED0 FSADDR0 AD25FSADDRU0 FSADDRU6 RN9 8 1 33R FSADDR6
Y21 B19 AD26FSADDRU1 FSADDRU7 7 2 FSADDR7
Y22 VRED1 FSADDR1
A19 VRED2 FSADDR2 AC24FSADDRU2 FSADDRU5 6 3 FSADDR5
Y23 D18 AC25FSADDRU3 FSADDRU8 5 4 FSADDR8
Y24 VRED3 FSADDR3
C18 VRED4 FSADDR4 AB26 FSADDRU4
Y25 B18 AA24 FSADDRU5 FSADDRU2 RN13 8 1 33R FSADDR2
Y26 VRED5 FSADDR5
A18 VRED6 FSADDR6 AA25 FSADDRU6 FSADDRU9 7 2 FSADDR9
L10 +3.3V_LVDSA L11 +1.8V_DVI Y27 C17 AA26 FSADDRU7 FSADDRU4 6 3 FSADDR4
+3.3V +3.3V_LVDSA +1.8V +1.8V_DVI VRED7 FSADDR7
CX000800000 CX000800000 Y24 FSADDRU8 FSADDRU11 FSADDR11
C103
C107
FSADDR8 5 4
C20 AB25 FSADDRU9
0.1u C104
0.1u C105
0.1u C106
0.1u C108
0.1u C109
0.1u C110
0.1u C111
A23 VGRN0 FSADDR9
C21 C22 AC26FSADDRU10 FSADDRU1 RN11 8 1 33R FSADDR1
C22 VGRN1 FSADDR10
B22 VGRN2 FSADDR11 AB24 FSADDRU11 FSADDRU0 7 2 FSADDR0
C23 A22 FSADDRU3 6 3 FSADDR3
47uF/6.3V
47uF/6.3V
C24 VGRN3
D21 VGRN4 FSCLKp U24 FSCLKU+ R80 33
FSCLK+ 6
FSADDRU10 5 4 FSADDR10
C25 C21 U23 FSCLKU- R81 33
C26 VGRN5 FSCLKn FSCLK- 6 FSBKSELU0 RN12 8
B21 VGRN6 1 33R FSBKSEL0 FSBKSEL0 6
C27 A21 F26 FSDQMU0 /FSRASU 7 2 /FSRAS
VGRN7 DM0 FSDQMU1 /FSRAS 6
DM1 N25 6 3
PAB0 B25 T26 FSDQMU2 5 4
PAB1 VBLU0 DM2 FSDQMU3
A25 VBLU1 DM3 K24
PAB2 D24 /FSWEU RN10 8 1 33R /FSWE
PAB3 VBLU2 FSDQSU0 FSCKEU FSCKE /FSWE 6
C24 VBLU3 DQS0 F25 7 2 FSCKE 6
PAB4 B24 N26 FSDQSU1 /FSCASU 6 3 /FSCAS
PAB5 VBLU4 DQS1 FSDQSU2 FSBKSELU1 FSBKSEL1 /FSCAS 6
A24 VBLU5 DQS2 U25 5 4 FSBKSEL1 6
PAB6 C23 J26 FSDQSU3
PAB7 VBLU6 DQS3
B23 VBLU7
FSCKE W26 FSCKEU
VCLK A20 Y25 FSBKSELU0
VODD VCLK FSBKSEL0
B20 Y26 FSBKSELU1
Gm1601
VVS VODD FSBKSEL1
C20 VVS
VHS_CSYNC D19 AC18
VDV VHS_CSYNC GPIO_G06_B0
D20 VDV GPIO_G06_B1 AD18
R86 10K VCLAMP B17 AE18
VCLAMP GPIO_G06_B2
GPIO_G06_B3 AF18
C26 PWM0 A3+ AE19 TXA3+
BRIGHTNESSC25 AF19 TXA3-
7 BRIGHTNESS LED_G PWM1 A3-
D26 PWM2 AC+ AE20 TXAC+ 3
LED_R D25 AF20 TXAC-
ADC_IN3
ADC_IN2
ADC_IN1
A12
B12
OCM_TIMER1
LBADC_IN3
LBADC_IN2
LCD TV / MONITOR CONTROLLER AC-
GPIO_G05_B0 AD21
1AM
C12 LBADC_IN1 GPIO_G05_B3 AD22 2 1

D12 AE21 TXA2+ +3.3V
LBADC_RETURN A2+
A2- AF21 TXA2- MMBT3904L
YUV0 C16 AE22 TXA1+
YUV1 SVDATA0 A1+
B16 SVDATA1 A1- AF22 TXA1- Component
YUV2 AE23 TXA0+
33K
33K
33K
33K
33K
33K
33K
0R
A16 SVDATA2 A0+
YUV3 D15 AF23 TXA0-
top view
YUV4 SVDATA3 A0-
C15 SVDATA4
YUV5 B15 AD23MENU
YUV6 SVDATA5 GPIO_G04_B0
A15 AD24SEL
R87
R88
R89
R90
R94
R91
R92
YUV7 SVDATA6 GPIO_G04_B1
D14 AE24 PWR CN3
R93
SVDATA7 GPIO_G04_B2
GPIO_G04_B3 AF24 DOWN 11
SVDV A17 AF25 UP MENU R95 1K
SVODD SVDV GPIO_G04_B4 +3.3V 10
R105 0R/NC AF26 RIGHT SEL R96 1K
AFN110-A2G1T
+5V A14 SVODD GPIO_G04_B5 9
SVVSYNC B14 AE25 LEFT PWR R97 1K
SVHSYNC SVVSYNC GPIO_G04_B6 6 DOWN R99 1K 8
C14 SVHSYNC GPIO_G04_B7 AE26 USB_CTRL 7
R100 10K SVCLK UP R101 1K
4606-04-04P-R
R103
D16 SVCLK 6
R110 0R CN4 AE8 RIGHT R102 1K
+3.3V GPIO_G07_B0 5
AF8 LEFT R104 1K
1 +5V 4 TXD GPIO_G07_B1 4
R106 0R M1 AC9 Q1 R107 100R
2 OCM_UDO GPIO_G07_B2 3
3
0R MMST3906 R109 100R
10K
3 M2 OCM_UDI GPIO_G07_B3 AD9 2
R108
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
4 4 RXD GPIO_G07_B4 AE9 1
VCC
AF9 LED_R R111 470R

GPROBE GPIO_G07_B5 +3.3V
OUT 1 K1 /RESET GPIO_G07_B6 AD10
IRDATA M4 AE10
IR1 GPIO_G07_B7
C112
C113
C114
C115
C116
C117
C118
M3
GND
MSTR_SCL R114 0R IR0
R116
P4 MSTR_SCL
MSTR_SDA R115 0R P3 AF10
U10 MSTR_SDA LVDS_SHIELD[0]
LVDS_SHIELD[1] AC11
MAX809_0 AD11 Q2
2
LVDS_SHIELD[2] MMST3906
LVDS_SHIELD[3] AE11
3 /OCM_WE AF11 TXB3+
10K
R3 /OCM_WE B3+
/OCM_RE R2 AF12 TXB3- LED_G R117 470R
/OCM_CS /OCM_RE B3-
2 1 R1 /ROM_CS BC+ AE12 TXBC+
R118 0R(NC) L1 /OCM_INT2 BC- AF13 TXBC-
R119 0R(NC) L2
R120 0R(NC) /OCM_INT1
P2 /OCM_CS2
R121 0R(NC) P1
+3.3V +3.3V R122 0R(NC) /OCM_CS1
T4 /OCM_CS0 LVDS_SHIELD[4] AE13
LVDS_SHIELD[5] AD14
AF14 TXB2+
14
14
OCMADDR19 B2+
U11 29LV040B T3 OCMADDR19 B2- AE14 TXB2- CN5
OCMDATA7 21 1 OCMADDR18 T2 AF15 TXB1+ TXA0- TXA0+
OCMDATA6 DQ7 A18 OCMADDR17 OCMADDR18 B1+ 1 2
11 10 13 12 20 DQ6 A17 30 T1 OCMADDR17 B1- AE15 TXB1- TXA1-
3 4
TXA1+
OCMDATA5 19 2 OCMADDR16 U4 AF16 TXB0+ TXA2- TXA2+ +3.3V
OCMDATA4 DQ5 A16 OCMADDR15 OCMADDR16 B0+ +3.3V 5 6
U7E U7F 18 DQ4 A15 3 U3 OCMADDR15 B0- AE16 TXB0- 7 8
74LCX14MX 74LCX14MX OCMDATA3 17 29 OCMADDR14 U2 TXAC- TXAC+
OCMDATA2 DQ3 A14 OCMADDR13 OCMADDR14 TXA3- 9 10 TXA3+
R123
15 28 U1
7
OCMDATA1 DQ2 A13 OCMADDR12 OCMADDR13 TXB0- 11 12 TXB0+
R124
14 DQ1 A12 4 V4 OCMADDR12 13 14
OCMDATA0 13 25 OCMADDR11 V3 AC7
DQ0 A11 OCMADDR10 OCMADDR11 DCLK TXB1- 15 16 TXB1+
A10 23 V2 OCMADDR10 GPIO_14 AF17 17 18
OCMADDR9 TXB2- TXB2+
10K(NC)
A9 26 V1 OCMADDR9 GPIO_15 AD16 19 20
/OCM_CS OCMADDR8 TXBC- TXBC+
10K(NC)
22 CE# A8 27 W3 OCMADDR8 GPIO_16 AD7 21 22
/OCM_RE 24 5 OCMADDR7 W2 TXB3- TXB3+
L12 +3.3V_ADC /OCM_WE OE# A7 OCMADDR6 OCMADDR7 23 24
+3.3V +3.3V_ADC 31 WE# A6 6 W1 OCMADDR6 25 26
CX000800000 OCMADDR5
C119
A5 7 Y3 OCMADDR5 27 28
OCMADDR4
0.1u C120
0.1u C121
0.1u C122
0.1u C123
0R(NC) R126
A4 8 Y2 OCMADDR4 29 30
OCMADDR3 R125 2.7K
R127
+3.3V 32 VCC A3 9 Y1 OCMADDR3 GPIO_G08_B5/JTAG_RESET AD8 +3.3V
10 OCMADDR2 AA3 AF7 1841-30P
A2 OCMADDR1 AA2 OCMADDR2 GPIO_G08_B4/JTAG_TDO
16 11 AE7
47uF/6.3V
VSS A1 OCMADDR0 AA1 OCMADDR1 GPIO_G08_B3

12 AF6
0R(NC)
A0 OCMADDR0 GPIO_G08_B2/JTAG_TDI
GPIO_G08_B1/JTAG_MODE AE6
A28F001 AD6 Panel_Power
GPIO_G08_B0/JTAG_CLK Panel_Power
L13 +3.3V_PLL
C124
+3.3V +3.3V_PLL GPIO_G09_B5 AF5
CX000800000 R128 0R
C126
0.1u C125
4 A/D_SEL AB3 OCMDATA15 GPIO_G09_B4 AE5
R129 0R
0.1u C127
0.1u C128
0.1u C129
0.1u C130
0.1u C131
0.1u C132
0.1u C133
4 EDID_SEL AB2 OCMDATA14 GPIO_G09_B3 AD5

R130 0R AB1 AC5 R131 10K
4 DEBUG OCMDATA13 GPIO_G09_B2 +3.3V
R132 0R AC3 AF4 R133 0R VGA_CAB
100uF/25V
7 SWITCH OCMDATA12 GPIO_G09_B1 VGA_CAB 4
+3.3V R134 0R AC2 AE4 R135 0R DVI_CAB
47uF/6.3V
7 INVSW OCMDATA11 GPIO_G09_B0 DVI_CAB 4

R136 0R(NC) AC1
R137 0R(NC) OCMDATA10
AD1 OCMDATA9
R138 0R(NC)
C134
AE1 OCMDATA8
OCMDATA7 A26 PPWR
0.1u C135
AF1 OCMDATA7 PPWR PPWR 7

+3.3V OCMDATA6 AD2 B26 PBIAS
OCMDATA5 OCMDATA6 PBIAS PBIAS 7 +3.3V
AE2 OCMDATA5
+3.3V OCMDATA4
R140
R141
AF2 AC17
47uF/6.3V
OCMDATA[0..7] OCMDATA3 OCMDATA4 NO_CONNECT

AD3 OCMDATA3 OEXTR AC16OEXTR R139 3.3K
OCMDATA2
R188
R189
R190
R191
R192
R193
R194
AE3 OCMDATA2 D_GND AD15

OCMDATA1 AF3 U12
OCMDATA0 OCMDATA1
0.1u C136
AD4 8 1
2.7K
2.7K
OCMDATA0 VCC A0
7 WP A1 2
MSTR_SCL
10K
10K
10K
10K
10K
10K
10K
6 SCK A2 3
MSTR_SDA 5 4
AC19VSSA33A_LVDS
AC20VSSA33A_LVDS
AD19VSSA33A_LVDS
OCMADDR8 SI VSS
VSSD33_DDDS
VSSD33_SDDS
VSSA33_DDDS
R142 0R R195 10K Socket for a X8 Flash (64/128/256/512K) and
VSSA33_SDDS
Custom1
AD17VSSD33_LVDS
VSSA33_RPLL
VSSA33_FPLL
OCMADDR9
VSSA18_DLL
VSSD33_PLL
D13 LBADC_GND
R143 0R(NC) R196 10K 24LC32-SN
AC13LVDSB_GND
AC14LVDSB_GND
Custom2 LVDSB_GND
K26 FSVREFVSS
W24 FSVREFVSS
PROMJETmemory Emulator
ADC_DGND
ADC_DGND
ADC_AGND
ADC_AGND
ADC_AGND
ADC_AGND
ADC_AGND
OSCSEL R197 10K OCMADDR10
DVI_GND
DVI_GND
DVI_GND
DVI_GND
DVI_GND
DVI_GND
DVI_GND
OUTPUTS_ZERO R198 10K OCMADDR12 10: LOW (Use TCLK)
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
11: LOW (set all display output to '0')

OUTPUTS_ZERO R199 10K OCMADDR11 12: LOW
R144 0R Serial_Interface_Debug1 R200 10K OCMADDR13 13: LOW(disable serial interface debug)
AC15
R145 0R R201 10K OCMADDR14 14: LOW

M15
M11
M13
M12
M16
M14
M10
M17
Serial_Interface_Debug2
U14
R15
U15
N11
R11
N17
N10
R10
N12
U12
N13
R13
N14
N15
N16
R16
R12
U13
R14
R17
D11
A13
P15
P16
K12
P12
K14
P14
B13
K25
K15
K13
P13
P11
P17
P10
A11
T12
T13
T10
T14
T15
L15
L12
L13
L10
L14
L17
G2
D4
C4
C7
D7
H4
H2
B4
E2
A5
E1
E4
A7
B7
B5
K4
F3
J4
J2
R146 0R(NC) Serial_Interface_Debug3 R202 10K OCMADDR15 15: LOW
16: HIGH (use crystal)
17: LOW (8bit bus with OCM access external ROM)
INT_OSC OCMADDR16 18: HIGH BGA416-26X26_1_27
8-BIT_FLASH2 OCMADDR18 19: LOW GM1601
8-BIT_FLASH1 R147 10K OCMADDR17 BOOTSTRAP HEADER
8-BIT_FLASH3 R148 10K OCMADDR19
OPEN=1
CONTROLLER
SHUNTED=0
Model
Title
Date Rev:

L14 +2.5V_DDR
+2.5V +2.5V_DDR
CX000800000
C137
C138
0.1u C139
0.1u C140
0.1u C141
0.1u C142
0.1u C143
0.1u C144
0.1u C145
0.1u C146
0.1u C147
0.1u C148
0.1u C149
0.1u C150
0.1u C151
0.1u C152
0.1u C153
0.1u C154
0.1u C155
0.1u C156
0.1u C157
0.1u C158
0.1u C159
0.1u C160
0.1u C161
0.1u C162
47uF/6.3V
47uF/6.3V
+2.5V_DDR FSVREF2
+2.5V_DDR FSVREF2
G11
C10
C12
N13
E12
K11
E11
F11
L11
J11
U13
G4
C3
C5
C7
C8
D7
D8
E3
K4
E4
F4
L4
L7
L8
J4
BGA144-12X12_0_8
FSDATA[0..31] 5
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VREF
B7 FSDATA0
5 FSADDR[0..11] FSADDR0 N5 DQ0 FSDATA1
A0 DQ1 C6
FSADDR1 N6 B6 FSDATA2
FSADDR2 M6 A1 DQ2 FSDATA3
A2 DQ3 B5
FSADDR3 N7 C2 FSDATA4
FSADDR4 N8 A3 DQ4 FSDATA5
A4 DQ5 D3
FSADDR5 M9 D2 FSDATA6
FSADDR6 N9 A5 DQ6 FSDATA7
A6 DQ7 E2
FSADDR7 N10
FSADDR8 N11 A7
FSADDR9 M8 A8/AP
FSADDR10 L6 A9
FSADDR11 M7 A10
+2.5V_DDR R203 10K A11 FSDATA8
L9 A12 DQ8 K13
K12 FSDATA9
FSBKSEL0 N4 DQ9 FSDATA10
R204
5 FSBKSEL0 BA0 DQ10 J13

FSBKSEL1 M5 J12 FSDATA11
5 FSBKSEL1 BA1 DQ11 FSDATA12
DQ12 G13
FSCLK- M12 G12 FSDATA13
10K(NC)
5 FSCLK- FSCLK+ CLK DQ13 FSDATA14

5 FSCLK+ M11 CLK DQ14 F13
FSCKE N12 F12 FSDATA15
5 FSCKE CKE DQ15
N2 CS
/FSRAS M2
5 /FSRAS /FSCAS RAS
R205
5 /FSCAS L2 CAS
/FSWE L3 F3 FSDATA16
5 /FSWE FSDQS0 WE DQ16 FSDATA17
5 FSDQS0 B2 DQS0 DQ17 F2
FSDQS1 H13 G3 FSDATA18
5 FSDQS1 FSDQS2 DQS1 DQ18 FSDATA19
0R
5 FSDQS2 H2 DQS2 DQ19 G2

FSDQS3 B13 J3 FSDATA20
5 FSDQS3 DQS3 DQ20 FSDATA21
DQ21 J2
K4D263238G-VC33
FSDQM0 B3 K2 FSDATA22
5 FSDQM0 FSDQM1 DM0 DQ22 FSDATA23
5 FSDQM1 H12 DM1 DQ23 K3
FSDQM2 H3
5 FSDQM2 FSDQM3 DM2
5 FSDQM3 B12 DM3
+2.5V_DDR C4 NC
C11 NC FSDATA24
R206
H4 NC DQ24 E13
H11 D13 FSDATA25
NC DQ25 FSDATA26
L9 NC DQ26 D12
FSCLK+ R149 140R FSCLK- L12 C13 FSDATA27
10K(NC)
NC DQ27 FSDATA28
L13 NC DQ28 B10
Place R602 termination close to M3 B9 FSDATA29
NC DQ29 FSDATA30
corresponding U600 Pins M4 NC DQ30 C9
M10 B8 FSDATA31
NC DQ31
R207
N3 NC
+2.5V_DDR
J9 VSS VSS G9
+2.5V_DDR J8 G8
0R(NC)
R150 VSS VSS

J7 VSS VSS G7
J6 VSS VSS G6
H9 VSS VSS F9
H8 VSS VSS F8
10K H7 F7
VSS VSS
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
H6 VSS VSSQ VSS F6
MCL
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
FSVREF
L15 FSVREF2
M13
G10
D10
D11
H10
B11
K10
E10
F10
L10
J10
FSVREF2
G5
D4
D5
D6
D9
H5
B4
E6
E9
K5
E5
E7
E8
K6
K7
K8
K9
F5
L5
J5
CX000800000
R151
0.1u C163
C164
0.01u
10K Model DDR

Title
Date Rev:

+12V
CX000800000 +18V
C200 L29 U24
1 2 +20V L32
R220 1 2 1 3
330u/16V
C203 VIN VOUT
C211
0.1u
C204
330u/16V
GND
1nF 0R CX000800000/NC
C208
0.1u
C205
C207
0.1u
C214
0.1u/NC
MC7818/CASE936/NC
AF4410N
220u/35V/NC
2
U23
5
6
7
8
CN7 +12V
220u/35V/NC
1 1 CS VIN 8
3
C215
2 2 ITH/RUN BOOST 7
3 3 FB DRI 6
C199 4 5
4 GND SW C202
Q9
4500-8P-R
330pF +5V
AIC1577 0.1u R222
4
3
2
1
47 L28 100uH CX000800000
L30
5 R217 2 1 1 2
1000u/6.3V
6 ADJ 24K
3
+20V
1000u/6.3V
7 ON/OFF D28 L16
2
C216
C206
8 +18V
C201 1nF 1 CX000800000/NC
C209
0.1u
C210
1nF
Vout=0.8(12K+62K)/12K=4.93 SPL1040PT L17
+12V
CX000800000/NC
L18
R158
1
2
+5V
CX000800000 Panel_Power
C166
Q4
R218 R219 AO4411
12K/1% 62K/1% 線1,線2的地要拉回點3,D28 L28 C216要互相靠近 1 8 L20
CX000800000
Modify Power AIC 1563 to
1u
2 7
4.7K
330u/16V
U16 3 6
AIC 1577 R161 0R(NC)
0.1u
0.1u
4 5
L23 3 2
+5V VIN VOUT +3.3V
CX000800000
C173
C174
C175
R221
1
2.2K
ADJ/GND USB_VDD
AIC1084/TO252 Q10 SI2301DS
200/1%
100u/16V
100u/16V
+5V
R166
+ + 1 3 3
MMBT3904
R162 4.7K 2
5 PPWR
C170 C169
Q5
C180
C181
1
R82 C167 R84
C168
330/1%
2200P/6 10K/6 330U/16V 0.1U/6
2
82K/6 2200P/6
R169
2
D 3 +5V
U18 R83
0.8A Max
R167
L25 3 2
+5V
CX000800000 VIN VOUT +2.5V
10K/6
G2 1
Q3 S
1 4 USB_VDD
4.7K/NC
ADJ/GND 4
3
DTC144EUA
LT1117/TO223
100u/16V
200/1%
100u/16V
2 USB_CTRL 4 CN6
R168 0R ON/OFF
R174
+ + 4 3 R216
C 3 2 1 0/NC 3
MMBT3904/NC
ENTERY_3273-G04N R170 4.7K/NC 2
C184
C185
5 PBIAS
Q7
1
1
B 2 1 E
200/1%
5 INVSW
R176
整塊線路靠近CN6,C169,C170更要靠近CN6
U20 +5V
L26
R173
+5V 3 VIN VOUT 2 +1.8V
CX000800000
1 ADJ/GND
3
100u/16V
AIC1084/TO252
100u/16V
330/1%
10K
+
R180
+ 2 1 R175 100K ADJ

C187
MMBT3904L TOP VIEW

C188
0.1u
3
147R/1%
MMBT3904
R177 4.7K 2
5 BRIGHTNESS
Q8
R181
C186
2
1 3
+3.3V
R178
2 4 1 3
H1 MTH276D126 H2 MTH276D126 H3 MTH276D126 H4 MTH276D126
RBS31 TOPVIEW AIC1084/TO252 TOP VIEW 2 9 2 9 2 9 2 9
10K
3 8 3 8 3 8 3 8
U19 RBS31 2 4 1 7 4 1 7 4 1 7 4 1 7
R179 220R 1 4 5 6 5 6 5 6 5 6
+3.3V SWITCH 5
2 3
Model POWER
1 3
Title
AIC1084/TO252 TOP VIEW
Date Rev:

11. PCB Layout Diagrams

* Reader’s Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagrams
10. Schematic Diagrams
11.PCB Layout Diagrams
B. Are you satisfied with this Service Manual?

Item Excellent Good Fair Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Reader’s basic dada:

Name: Title:
Company:
Add:
Tel: Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
([email protected])

Service Manual: Viewsonic Vp2030B-1

Uploaded by

Copyright:

Available Formats

Service Manual: Viewsonic Vp2030B-1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: Viewsonic Vp2030B-1

Uploaded by

Copyright:

Available Formats

Service Manual

(VP2030b-1_SM Rev. 1b Jan. 2007)

1a 12/23/2005 Initial Release Jamie Chang

1b 01/05/2007 VS-E060426 Add 2nd panel source Jamie Chang

Viewsonic Corporation i Confidential - Do Not Copy VP2030b-1

1. Precautions and Safety Notices 1

3. Front Panel Function Control Description 10

6. Trouble Shooting Flow Chart 53

7. Recommended Spare Parts List 60

8. Exploded View And Exploded Parts List 63

10. Schematic Diagrams 68

11. PCB Layout Diagrams 73

Viewsonic Corporation ii Confidential - Do Not Copy VP2030b-1

3. POWER SUPPLY REQUIREMENTS

4. LEAKAGE CURRENT HOT CHECK

To Metal Parts 1500 10W Earth Ground

Viewsonic Corporation 1 Confidential - Do Not Copy VP2030b-1

Correct methods : Incorrect Methods :

Viewsonic Corporation 2 Confidential - Do Not Copy VP2030b-1

Correct methods : Incorrect Methods :

Viewsonic Corporation 3 Confidential - Do Not Copy VP2030b-1

Test Resolution & Frequency 1600x1200 @ 60Hz

Input Connector (refer the appendix A) D-Sub = DB-15 (Analog)

Exclusions Not compatible with interlaced video

Viewsonic Corporation 4 Confidential - Do Not Copy VP2030b-1

Up Stream Connector B type USB port x1

Internal Power Supply Delta EADP-64BF

Viewsonic Corporation 5 Confidential - Do Not Copy VP2030b-1

Horizontal / Vertical Frequency

1 640 x 350 @ 70 Hz, 31.5 KHz ü ü SOG

Viewsonic Corporation 6 Confidential - Do Not Copy VP2030b-1

Viewsonic Corporation 7 Confidential - Do Not Copy VP2030b-1

Viewsonic Corporation 8 Confidential - Do Not Copy VP2030b-1

1st Source Panel

2nd Source Panel

Viewsonic Corporation 9 Confidential - Do Not Copy VP2030b-1

Front Control Panel

Viewsonic Corporation 10 Confidential - Do Not Copy VP2030b-1

Main Menu Controls

Viewsonic Corporation 11 Confidential - Do Not Copy VP2030b-1

Viewsonic Corporation 12 Confidential - Do Not Copy VP2030b-1

CN6 PIN MNEMONIC SIGNAL

DB15HD 1 RV Red Video

Viewsonic Corporation 13 Confidential - Do Not Copy VP2030b-1

CN2 Pin No. Signal Name Description

Viewsonic Corporation 14 Confidential - Do Not Copy VP2030b-1

Display Area 408.0 x 306.0 mm

3.2.2 Power Management

State Power Indicator

Standby < 3Watts Amber

3.3 Acceptable timing

Viewsonic Corporation 15 Confidential - Do Not Copy VP2030b-1

Viewsonic Corporation 16 Confidential - Do Not Copy VP2030b-1

Viewsonic Corporation 17 Confidential - Do Not Copy VP2030b-1

Viewsonic Corporation 18 Confidential - Do Not Copy VP2030b-1

Digital Separate, Horizontal Polarity (+) Vertical Polarity (+)

Monitor Serial Number:

Monitor Range Limits:

(126) No Extension EDID Block(s)