Scribd Logo
Upload

Welcome to Scribd!

  • 39 views

    IS11002 NV Series Configuring Power Boost Presets

    Uploaded by

    BG Jluis
    Configuración presets poder

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    IS11002 NV Series Configuring Power Boost Presets

    Uploaded by

    BG Jluis
    39 views5 pages
    Configuración presets poder

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Configuración presets poder

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    39 views5 pages

    IS11002 NV Series Configuring Power Boost Presets

    Uploaded by

    BG Jluis
    Configuración presets poder

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    Information Sheet

    IS11002

    NV Series –
    Configuring HD
    PowerBoost
    Presets

    Issue 1.0 ......................... 22 February 2011

    Nautel Limited
    10089 Peggy's Cove Road,
    Hackett's Cove, NS, Canada B3Z 3J4
    T. +1.877 6 nautel (628835) or +1.902.823.2233
    F.+1.902.823.3183 [email protected]

    U.S. customers please contact:


    Nautel Inc.
    201 Target Industrial Circle, Bangor ME 04401
    T.+1.877 6 nautel (628835) or +1.207.947.8200
    F.+1.207.947.3693 [email protected]

    e-mail: [email protected]
    www.nautel.com

    © Copyright 2011 NAUTEL. All rights reserved.


    IS11002: NV Series – Configuring HD PowerBoost
    Presets
    INFORMATION SHEET
    1 INTRODUCTION
    This document describes how to use the NV transmitter’s local or remote advanced user
    interface (AUI) to configure an HD PowerBoost preset.

    1.1 Equipment Affected


    This procedure applies to NV series transmitters that have been factory equipped or field
    modified with the Nautel Part # NAE104/01 or NAE105/01 Digital Exciter and have the
    PowerBoost license enabled.

    1.1.1 Minimum Software Required


    NV SW version 3.0. This is included with NV transmitters containing the exciters referenced
    in paragraph 1.1.

    1.2 Responsibility for Implementation of Procedure


    This procedure should be carried out by qualified station maintenance personnel who are
    familiar with the operation of NV series transmitters.

    1.3 Scheduling
    This procedure must be performed when operation with a PowerBoost preset is desired. The
    transmitter can remain “on air” during this procedure.

    1.4 Manpower Requirements


    Implementing this modification will require approximately 10 minutes.

    1.5 Special Tools/Test Equipment


    None.

    1.6 Publications Affected


    This modification does not affect the NV series documentation. AUI screens that are pertinent
    to configuring HD PowerBoost presets are included in this document.

    NV Series – Configuring HD PowerBoost Presets Page 1


    IS11002 Issue 1.0
    2 CONFIGURING A POWERBOOST PRESET
    Configure an HD PowerBoost preset, using the AUI on the local front panel or remotely
    accessed web-interface as follows:

    NOTE
    It is recommended that a user configuring an HD PowerBoost preset be familiar with the
    transmitter’s AUI. As necessary, refer to “Section 2: Operating the Transmitter” of the NV
    Operations and Maintenance Manual for detailed information on the AUI and its Presets
    page.

    In order to enable HD PowerBoost, you must use the AUI’s Presets page to either load an
    existing PowerBoost preset or create a new PowerBoost preset. For general details on
    loading, editing and activating a preset, refer to the “Editing and Saving Presets” paragraph
    under “Operating Presets” in Section 2 of the NV Operations and Maintenance Manual. For
    specific detail on creating HD PowerBoost presets, follow the naming convention described
    below:

    For PowerBoost presets, the name must begin with the characters ‘PB’ (not case sensitive),
    followed by one or two numbers that indicate the IBOC power injection ratio levels, and finally
    the characters ‘dBc’. See Figure 1 for examples of this naming convention.

    Injection ratios, which can be expressed in 0.1 dB increments, represent the nominal
    symmetric MP1 level. If only one number appears in the preset name, a symmetric mode is
    selected. If two numbers appear in the preset name, the first number is applied to the lower
    sideband and the second number to the upper sideband. The two numbers can be separated
    via spaces or slashes. The ‘–‘ sign is optional.

    The preset injection field (see Figure 2) is ignored in PowerBoost mode; it should be set to
    -20 dB at all times.

    Examples of -10 dB, -20 dB


    and -14 dB symmetric
    PowerBoost presets

    Examples of asymmetric mode


    PowerBoost presets. First number
    applies to lower sideband; second
    number to upper sideband.

    Figure 1: PowerBoost Preset Examples (shown using the Load button)

    Page 2 NV Series – Configuring HD PowerBoost Presets


    Issue 1.0 IS11002
    This field is ignored
    in PowerBoost
    mode; set to -20 dB

    Figure 2: Presets Page showing PowerBoost Preset

    3 RESUMING TRANSMITTER OPERATION


    This completes the procedure. Select (activate) the desired preset for transmitter operation.

    If you have any questions or require additional assistance, please contact


    Nautel’s Customer Service Department at:

    Telephone: 1-902-823-5100

    Email: [email protected]

    NV Series – Configuring HD PowerBoost Presets Page 3


    IS11002 Issue 1.0

    You might also like