Scribd
Upload
3K views3 pages

EXP17 Class A Power Amplifier

This document describes an experiment to study the operation of a Class A power amplifier. Class A amplifiers operate in the active region for the entire input signal cycle, so collector current flows continuously even without an input signal. The experiment involves building a Class A amplifier circuit, applying a 1 kHz sinusoidal input signal, and measuring the output waveform on an oscilloscope. Key measurements include input and output signal amplitudes to calculate voltage gain. Analysis questions address comparing theoretical and practical results, deriving efficiency laws, and discussing types of distortion.

Uploaded by

Mohammed Dyhia Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views3 pages

EXP17 Class A Power Amplifier

This document describes an experiment to study the operation of a Class A power amplifier. Class A amplifiers operate in the active region for the entire input signal cycle, so collector current flows continuously even without an input signal. The experiment involves building a Class A amplifier circuit, applying a 1 kHz sinusoidal input signal, and measuring the output waveform on an oscilloscope. Key measurements include input and output signal amplitudes to calculate voltage gain. Analysis questions address comparing theoretical and practical results, deriving efficiency laws, and discussing types of distortion.

Uploaded by

Mohammed Dyhia Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Middle Technical University Electronics Lab.

Electrical Engineering Technical College 2nd Stage


Electrical Power Technical Engineering Dept. Mohammed D. Altamemi

Experiment 17
Class A Power Amplifier

17-1 Object:

In this experiment we will study the operation of a power amplifier class A.

17-2 Theory:

The class A amplifiers are the amplifiers which deliver maximum


undistorted symmetrical output voltage swing to the low impedance load.
Generally any system (like a stereo, radio or television) consists of several
stages of amplification. When the signal passes through these stages, the
power level of signal rises so much that the later stages require high power
handling circuit elements such as power transistors. Also as the load
impedance of these later stages is very small (of the order of 8 ohm for
stereo amplifier speakers), heavy collector current flows. To handle this,
transistors heaving power rating of 1W or more are used in power
amplifiers.

Class A amplifier is basically a voltage amplifier in which transistor


operates in active region for the entire cycle of input AC signal. In other
words the collector current flows for 360° of AC signal

Figure 17-1: input waveform of class A power amplifier

For class A amplifiers the Q point is located somewhere near the middle of the
AC load line and thus offers maximum amplification of the input signal as shown
below :

The collector current IC is non-zero even when the input signal is zero i.e. the
IC flows for 100% of time. This leads to power dissipation even in quiescent
condition.

MD
Middle Technical University Electronics Lab.
Electrical Engineering Technical College 2nd Stage
Electrical Power Technical Engineering Dept. Mohammed D. Altamemi

Figure (17-2) effect of input signal on output current and voltage

17-3 Procedures:

Circuit used to study the operation of Class A Amplifier is shown below :

Figure (17-3) connection of class A power amplifier

 Connect +12V variable DC power supplies at their indicated position from


external source.

MD
Middle Technical University Electronics Lab.
Electrical Engineering Technical College 2nd Stage
Electrical Power Technical Engineering Dept. Mohammed D. Altamemi

 Connect Vp-p = 600m V sinusoidal wave with (1KHz) at the Vin input of the
circuit.
 Connect Oscilloscope at the output terminals and observe
the output waveform.
 Gradually increase the input signal up to the value before the signal
just get clipped or decrease the DC supply voltage to the value before the
signal just get clipped. This is the maximum amplification of Class A
Amplifier.
 Calculate the peak-to-peak value of the output signal.

Results

 Draw the input and output signals of class A Amplifier 600 mV p.p.
 Input ac signal amplitude (Vin) : ...................................Vp-p
 Output ac signal amplitude (Vout) : ...................................Vp-p
 Voltage gain (A = Vout/Vin) : ................................... at 600mV p.p

17-4 Discussions:

1. Compare between the theoretical and your practical results.


2. Derive the laws of efficiency and maximum efficiency used in calculations.
3. Discuss the various types of distortion in amplification and how they can be
minimized?

MD

You might also like