4/3/2018 Quiz - Quizizz

Quizizz Name :
Class :
NACE Date :

1. HOW DOES NACE DEFINE THE INSPECTORS ROLE?

a) THE INSPECTORS ROLE IS b) MAKING CHANGES TO THE

THAT OF A QUALITY SPECIFICATIONS FOR ANY
CONTROL TECHNICIAN REASON
RESPONSIBLE FOR
OBSERVING AND
REPORTING
CONFORMANCE OR
DEVIATION FROM THE
PROJECT SPECIFICATIONS
c) TO ENFORCE THEIR OWN d) PRODUCE DATA SHEETS
SPECIFICATIONS AS TO ON SPECIFICATIONS
THE PROJECT

2. WHAT IS THE INSPECTORS RESPONSIBILITY, WHEN IT COMES TO SAFETY ON THE PROJECT

a) SAFETY ENFORCEMENT IS b) KNOWING SAFETY

NOT THE RESPONSIBILITY SPECIFICATIONS ON HAND
OF THE INSPECTOR, ON MAINTAINED ON A
HOWEVER IT IS HIS/HER COATING PROJECT
RESPONSIBILITY TO
REPORT ANY ISSUES THAT
MAY EFFECT THE
PROJECT
c) KNOWING PRIMARY d) MAKING NECESSARY
RESPONSIBILITY AND SPECIFICATIONS ON THE
WHAT THE INSPECTOR PROJECT AS NEEDED
SHOULD NOT DO AS TO
SPECIFICATIONS

https://quizizz.com/print/quiz/56e4be7fac2c58b43abf3208 1/6
4/3/2018 Quiz - Quizizz

3. NAME SOME OF THE DOCUMENTATION/REPORTS THAT MAY BE REQUIRED TO BE MAINTAINED ON A

COATING PROJECT

a) DAILY, WEEKLY SUMMARY, b) ANCHOR PROFILE, DAILY,

MATERIAL USAGE REPORT, SPREED SHEETS,
MAN POWER & EQUIPMENT
c) METHODS AND d) TCC, OMC, AND AMC
EQUIPMENT, SHEETS
ENVIRONMENTAL, DEBRIS
SHEETS

4. NAME SOME TEST THAT MAY NEED TO BE CONDUCTED DURING SURFACE PREPARATION AND
COATING OPERATIONS

a) TEMPERATURE, RELATIVE b) TEMPERATURE,

HUMIDITY, DEW POINT, OXIDIZATION,
ANCHOR PROFILE, CONDUCTION
SURFACE CLEANLINESS
c) TEMPERATURE, d) TEMPERATURE,
CONDUCTION, WALL PRESSURE, COATING,
THICKNESS, OXIDIZATION THICKNESS

5. WHAT ARE THE MOST IMPORTANT CHARACTERISTICS OF A GOOD REPORT

a) OBJECTIVE, ACCURATE, b) OBJECTIVE, PUNCTUATION,

AND DETAILED AND WORDING
c) OBJECTIVE, PLACE, AND d) OBJECTIVE, TRUE, AND
TIME NICE

6. WHAT IS THE INSPECTORS PRIMARY RESPONSIBILITY AND WHAT SHOULD THE INSPECTOR NOT DO
AS IT PERTAINS TO THE SPECIFICATION

a) THE INSPECTORS PRIMARY b) THE INSPECTORS PRIMARY

RESPONSIBILITY AS THE RESPONSIBILITY AS THE
INSPECTOR IS TO INSPECTOR IS TO
ENFORCE THE ENFORCE COATING
SPECIFICATION AND NOT SAFETY
MAKE CHANGES TO THE
SPECIFICATION FOR ANY
REASON
c) THE INSPECTORS PRIMARY d) THE INSPECTORS PRIMARY
RESPONSIBILITY AS THE RESPONSIBILITY IS TO
INSPECTOR IS TO MAKE CHANGES TO THE
ENFORCE CLEANLINESS SPECIFICATIONS
https://quizizz.com/print/quiz/56e4be7fac2c58b43abf3208 2/6
4/3/2018 Quiz - Quizizz

7. WHAT TYPE OF INFORMATION COULD YOU EXPECT TO FIND ON A PRODUCT DATA SHEET

a) ENVIRONMENTAL b) HEALTH, SAFETY AND

PARAMETERS FOR ENVIRONMENTAL
APPLICATION SUCH AS
MAX AND MINIMUM
TEMPERATURES, CURING
TIMES, RECOATING
WINDOWS
c) PHYSICAL d) EMERGENCY RESPONDER
CHARACTERISTICS INFORMATION

8. WHAT TYPE OF INFORMATION COULD YOU EXPECT TO FIND ON A SAFETY DATA SHEET

a) EQUIPMENT AND b) HEALTH, SAFETY &

PARAMETERS ENVIRONMENTAL,
REQUIRED PPE, PHYSICAL
CHARACTERISTICS,
EMERGENCY RESPONDER
INFORMATION
c) APPLICATIONS, METHODS d) MAXIMUM AND MINIMUM
AND EQUIPMENT SIZES CURING TIMES

9. EXPLAIN THE DIFFERENCE BETWEEN QUALITY ASSURANCE AND QUALITY CONTROL

a) QUALITY ASSURANCE b) QUALITY ASSURANCE:

PROCESS OF CHECKING ASSURING THE PRODUCT
TO SEE WHETHER A WILL WORK
PRODUCT BEING QUALITY CONTROL:
DEVELOPED IS MEETING MAKING SURE CRITERIA
SPECIFIED REQUIRMENTS DOESN'T MEET
QUALITY CONTROL: A REQUIREMENTS OF CLIENT
PROCEDURE OR SET OF
PROCEDURES INTENDED
TO ENSURE THAT A
PRODUCT ADHERES TO A
DEFINED SET OF QUALITY
CRITERIA

https://quizizz.com/print/quiz/56e4be7fac2c58b43abf3208 3/6
4/3/2018 Quiz - Quizizz

10. IDENTIFY SOME OF THE DEFECTS THAT CAN BE CAUSED BY INCORRECT APPLICATION
TEMPERATURES

a) FAILURE TO CURE, TOO b) CURING TIMES, BUBBLES,

RAPID SOLVENT STREAKING
EVAPORATION, POOR FILM
FORMATION
c) HIGH SATURATION, d) FAILURE TO FORM,
MOISTURE, FLAKING DRIPPING, DRY SPRAY

11. DESCRIBE RELATIVE HUMIDITY

a) THE AMOUNT OF b) THE TEMPERATURE AT

MOISTURE IN THE AIR WHICH MOISTURE WILL
COMPARED TO BEGIN TO FORM ON A
SATURATION LEVEL STEEL SURFACE
c) THE AMOUNT OF d) THE AMOUNT OF
MOISTURE IN THE AIR MOISTURE ON THE STEEL
COMPARED TO AFTER COATING
TEMPERATURES

12. WHAT IS THE DEW POINT TEMPERATURE

a) THE TEMPERATURE AT b) THE TEMPERATURE AT

WHICH MOISTURE WILL WHICH MOISTURE WILL
BEGIN TO FORM ON A BEGIN TO FORM ON
STEEL SURFACE COATING
c) THE TEMPERATURE AT d) THE TEMPERATURE AT
WHICH MOISTURE WILL WHICH DEW BECOMES
DRIP WATER

13. NAME SOME OF THE EFFECTS WIND MAY HAVE ON A COATING PROJECT

a) BLOWING ABRASIVES, b) EXCESSIVE SOLVENT

CAUSING EXCESSIVE ACCELERATION,
DRIFT OR OVER SPRAY, MOISTURE, FAILURE TO
ACCELERATING SOLVENT CURE
EVAPORATION,
CONTRIBUTING TO THE
FORMATION OF DRY SPARY
c) POOR FILM FORMATION, d) EXCESSIVE HEAT CURING,
ABRASIVES, EXCESSIVE SOLVENT
CONTRIBUTING TO SPOTS ACCELERATION, FAILURE
TO CURE, IONS MIXING
https://quizizz.com/print/quiz/56e4be7fac2c58b43abf3208 4/6
4/3/2018 Quiz - Quizizz

14. WHAT ARE SOME OF THE COMMON ERRORS WHEN USING AN ELECTRONIC HYGROMETER

a) FAILURE TO ACCLIMATE b) FAILURE TO ACCLIMATE

THE INSTRUMENT TO THE THE ENVIRONMENT
ENVIRONMENT WITH
ADEQUATE TIME
c) FAILURE TO CHECK d) FAILURE TO RECEIVE 3
PARAMETERS OF CONSECUTIVE READINGS
ENVIRONMENT AND
ATMOSPHERE

15. EXPLAIN THE PROCESS FOR USE OF THE SLING PSYCHROMETER

a) MAKE SURE THE WICK IS b) MAKE SURE THE METER IS

WET AND CLEAN, DRY AND STICKY,
CONTINUE TO "SLING" CONTINUE TO "SLING"
UNTIL 3 CONSECUTIVE UNTIL 4 CONSECTUTIVE
READINGS ARE ACHIEVED READINGS ARE ACHIEVED
c) MAKE SURE THE WICK IS d) MAKE SURE THE WICK IS
DRY AND STICKY, WET AND CLEAN,
CONTINUE TO "SLING" CONTINUE TO "SLING"
UNTIL 3 CONSECUTIVE UNTIL 6 CONSECUTIVE
READINGS ARE ACHIEVED READINGS ARE ACHIEVED

https://quizizz.com/print/quiz/56e4be7fac2c58b43abf3208 5/6
4/3/2018
Answer Key Quiz - Quizizz

1. a
2. a
3. a
4. a
5. a
6. a
7. a
8. b
9. a
10. a
11. a
12. a
13. a
14. a
15. a

https://quizizz.com/print/quiz/56e4be7fac2c58b43abf3208 6/6