iTNC 530: User's Manual Cycle Programming

User’s Manual
Cycle Programming
iTNC 530
NC Software
340 490-06, 606 420-01
340 491-06, 606 421-01
340 492-06
340 493-06
340 494-06
English (en)
6/2010
About this Manual
About this Manual
The symbols used in this manual are described below.
This symbol indicates that important information about the

function described must be considered.
This symbol indicates that there is one or more of the

following risks when using the described function:
Danger to workpiece
Danger to fixtures
Danger to tool
Danger to machine
Danger to operator
This symbol indicates that the described function must be

adapted by the machine tool builder. The function
described may therefore vary depending on the machine.
This symbol indicates that you can find detailed

information about a function in another manual.
Would you like any changes, or have you found

any errors?
We are continuously striving to improve documentation for you.
Please help us by sending your requests to the following e-mail
address: [email protected].
HEIDENHAIN iTNC 530 3

TNC Model, Software and Features
This manual describes functions and features provided by TNCs as of
the following NC software numbers.
TNC model NC software number

iTNC 530 340 490-06
iTNC 530 E 340 491-06
iTNC 530 340 492-06
iTNC 530 E 340 493-06
iTNC 530 programming station 340 494-06
TNC model NC software number

iTNC 530, HSCI and HeROS 5 606 420-01
iTNC 530, HSCI and HeROS 5 606 421-01
The suffix E indicates the export version of the TNC. The export
version of the TNC has the following limitations:
Simultaneous linear movement in up to 4 axes
HSCI (HEIDENHAIN Serial Controller Interface) identifies the new
hardware platform of the TNC controls.
HeROS 5 identifies the new operating system of HSCI-based TNC
controls.
The machine tool builder adapts the usable features of the TNC to his
machine by setting machine parameters. Some of the functions
described in this manual may therefore not be among the features
provided by the TNC on your machine tool.
TNC functions that may not be available on your machine include:
Tool measurement with the TT
Please contact your machine tool builder to become familiar with the
features of your machine.
4
Many machine manufacturers, as well as HEIDENHAIN, offer
programming courses for the TNCs. We recommend these courses as
an effective way of improving your programming skill and sharing
information and ideas with other TNC users.
User's Manual:
All TNC functions that have no connection with cycles are
described in the User's Manual of the iTNC 530. Please
contact HEIDENHAIN if you require a copy of this User’s
Manual.
ID of Conversational Programming User's Manual:
670 387-xx.
ID of User’s Manual for ISO programming: 670 391-xx.
smarT.NC user documentation:

The smarT.NC operating mode is described in a separate
Pilot. Please contact HEIDENHAIN if you require a copy of
this Pilot. ID: 533 191-xx.

Software options
The iTNC 530 features various software options that can be enabled
by your machine tool builder. Each option is to be enabled separately
and contains the following respective functions:
Software option 1
Cylinder surface interpolation (Cycles 27, 28, 29 and 39)
Feed rate in mm/min for rotary axes: M116
Tilting the machining plane (Cycle 19, PLANE function and 3-D ROT
soft key in the Manual operating mode)
Circle in 3 axes with tilted working plane
Software option 2
Block processing time 0.5 ms instead of 3.6 ms
5-axis interpolation
Spline interpolation
3-D machining:
M114: Automatic compensation of machine geometry when
working with swivel axes
M128: Maintaining the position of the tool tip when positioning
with tilted axes (TCPM)
FUNCTION TCPM: Maintaining the position of the tool tip when
positioning with tilted axes (TCPM) in selectable modes
M144: Compensating the machine’s kinematic configuration for
ACTUAL/NOMINAL positions at end of block
Additional parameters for finishing/roughing and tolerance
for rotary axes in Cycle 32 (G62)
LN blocks (3-D compensation)
DCM Collision software option

Function which dynamically monitors areas defined by the machine
manufacturer to prevent collisions.
Additional Conversational Language software option

Function for enabling the conversational languages Slovenian,
Slovak, Norwegian, Latvian, Estonian, Korean, Turkish, Romanian,
Lithuanian.
DXF Converter software option

Extract contours from DXF files (R12 format).
6
Global Program Settings software option
Function for superimposing coordinate transformations in the
Program Run modes.
AFC software option

Function for adaptive feed-rate control for optimizing the machining
conditions during series production.
KinematicsOpt software option

Touch-probe cycles for inspecting and optimizing the machine
accuracy.
3D-ToolComp software option

3-D radius compensation depending on the tool’s contact angle for
LN blocks.

Feature content level (upgrade functions)
Along with software options, significant further improvements of the
TNC software are managed via the Feature Content Level (FCL)
upgrade functions. Functions subject to the FCL are not available
simply by updating the software on your TNC.
All upgrade functions are available to you without

surcharge when you receive a new machine.
Upgrade functions are identified in the manual with FCL n, where n

indicates the sequential number of the feature content level.
You can purchase a code number in order to permanently enable the
FCL functions. For more information, contact your machine tool
builder or HEIDENHAIN.
FCL 4 functions Description

Graphical depiction of the protected User’s Manual
space when DCM collision monitoring is
active
Handwheel superimposition in stopped User’s Manual

condition when DCM collision
monitoring is active
3-D basic rotation (set-up Machine manual

compensation)

Touch probe cycle for 3-D probing Page 451
Touch probe cycles for automatic datum Page 345

setting using the center of a slot/ridge
Feed-rate reduction for the machining of User’s Manual

contour pockets with the tool being in
full contact with the workpiece
PLANE function: Entry of axis angle User’s Manual
User documentation as a User’s Manual

context-sensitive help system
smarT.NC: Programming of smarT.NC User’s Manual

and machining can be carried out
simultaneously
smarT.NC: Contour pocket on point smarT.NC Pilot

pattern
8
smarT.NC: Preview of contour smarT.NC Pilot
programs in the file manager
smarT.NC: Positioning strategy for smarT.NC Pilot

machining point patterns

3-D line graphics User’s Manual
Virtual tool axis User’s Manual
USB support of block devices (memory User’s Manual

sticks, hard disks, CD-ROM drives)
Filtering of externally created contours User’s Manual
Possibility of assigning different depths User’s Manual

to each subcontour in the contour
formula
DHCP dynamic IP-address User’s Manual

management
Touch-probe cycle for global setting of Page 456

touch-probe parameters
smarT.NC: Graphic support of block smarT.NC Pilot

scan
smarT.NC: Coordinate transformation smarT.NC Pilot
smarT.NC: PLANE function smarT.NC Pilot
Intended place of operation

The TNC complies with the limits for a Class A device in accordance
with the specifications in EN 55022, and is intended for use primarily
in industrially-zoned areas.

New Cycle Functions of Software 340 49x-02
New Cycle Functions of Software
340 49x-02
New machine parameter for defining the positioning speed (see
“Touch trigger probe, rapid traverse for positioning: MP6151” on
page 317)
New machine parameter for consideration of basic rotation in
Manual Operation (see “Consider a basic rotation in the Manual
Operation mode: MP6166” on page 316)
Cycles 420 to 431 for automatic tool measurement were improved
so that the measuring log can now also be displayed on the screen
(see “Recording the results of measurement” on page 397)
A new cycle that enables you to set global touch probe parameters
was introduced (see “FAST PROBING (Cycle 441, DIN/ISO: G441,
FCL 2 Function)” on page 456)
10
340 49x-03
New cycle for setting a datum in the center of a slot (see “SLOT
CENTER REF PT (Cycle 408, DIN/ISO: G408, FCL 3 Function)” on
page 345)
New cycle for setting a datum in the center of a ridge (see “RIDGE
CENTER REF PT (Cycle 409, DIN/ISO: G409, FCL 3 function)” on
page 349)
New 3-D probing cycle (see “MEASURING IN 3-D (Cycle 4, FCL 3
function)” on page 451)
Cycle 401 now also allows you to compensate workpiece
misalignment by rotating the rotary table (see “BASIC ROTATION
from Two Holes (Cycle 401, DIN/ISO: G401)” on page 325)
Cycle 402 now also allows you to compensate workpiece
misalignment by rotating the rotary table (see “BASIC ROTATION
over Two Studs (Cycle 402, DIN/ISO: G402)” on page 328)
In the cycles for datum setting, the results of measurement are
available in the Q parameters Q15X (see “Measurement results in Q
parameters” on page 399)

340 49x-04
New cycle for saving a machine's kinematic configuration (see
“SAVE KINEMATICS (Cycle 450, DIN/ISO: G450; Option)” on page
464)
New cycle for testing and optimizing a machine's kinematic
configuration (see “MEASURE KINEMATICS (Cycle 451, DIN/ISO:
G451; Option)” on page 466)
Cycle 412: Number of measuring points selectable through
parameter Q423 (see “DATUM FROM INSIDE OF CIRCLE (Cycle
412, DIN/ISO: G412)” on page 360)
parameter Q423 (see “DATUM FROM OUTSIDE OF CIRCLE (Cycle
413, DIN/ISO: G413)” on page 364)
parameter Q423 (see “MEASURE HOLE (Cycle 421, DIN/ISO:
G421)” on page 408)
parameter Q423 (see “MEAS. CIRCLE OUTSIDE (Cycle 422,
DIN/ISO: G422)” on page 412)
Cycle 3: Error message can be suppressed if the stylus is already
deflected when a cycle starts (see “MEASURING (Cycle 3)” on
page 449)
New cycle for rectangular stud milling (see “RECTANGULAR STUD
(Cycle 256, DIN/ISO: G256)” on page 160)
New cycle for circular stud milling (see “CIRCULAR STUD (Cycle
257, DIN/ISO: G257)” on page 164)
12
340 49x-05
New machining cycle for single-fluted deep-hole drilling (see
“SINGLE-FLUTED DEEP-HOLE DRILLING (Cycle 241, DIN/ISO:
G241)” on page 98)
Touch Probe Cycle 404 (SET BASIC ROTATION) was expanded by
parameter Q305 (Number in table) in order to write basic rotations
to the preset table (see page 335)
Touch Probe Cycles 408 to 419: The TNC now also writes to line 0
of the preset table when the display value is set (see “Saving the
calculated datum” on page 344)
Touch Probe Cycle 412: Additional parameter Q365 "type of
traverse" (see “DATUM FROM INSIDE OF CIRCLE (Cycle 412,
traverse" (see “DATUM FROM OUTSIDE OF CIRCLE (Cycle 413,
Touch Probe Cycle 416: Additional parameter Q320 (setup
clearance, see "DATUM CIRCLE CENTER (Cycle 416, DIN/ISO:
G416)", page 377)
traverse" (see “MEASURE HOLE (Cycle 421, DIN/ISO: G421)” on
page 408)
traverse" (see “MEAS. CIRCLE OUTSIDE (Cycle 422, DIN/ISO:
G422)” on page 412)
Touch Probe Cycle 425 (MEASURE SLOT) was expanded by
parameters Q301 (Move to clearance height) and Q320 (setup
clearance) (see "MEASURE INSIDE WIDTH (Cycle 425, DIN/ISO:
G425)", page 424)
Touch Probe Cycle 450 (SAVE KINEMATICS) was expanded by input
option 2 (Display saving status) in parameter Q410 (mode) (see
“SAVE KINEMATICS (Cycle 450, DIN/ISO: G450; Option)” on page
464)
Touch Probe Cycle 451 (MEASURE KINEMATICS) was expanded by
parameters Q423 (Number of circular measurements) and Q432
(Set preset) (see “Cycle parameters” on page 475)
New Touch Probe Cycle 452 (PRESET COMPENSATION) simplifies
the measurement of tool changer heads (see “PRESET
COMPENSATION (Cycle 452, DIN/ISO: G452, Option)” on page
482)
New Touch Probe Cycle 484 for calibrating the wireless TT 449 tool
touch probe (see “CALIBRATING THE WIRELESS TT 449 (Cycle
484, DIN/ISO: G484)” on page 500)

340 49x-06
New Cycle 275 "Trochoidal Contour Slot"(see “TROCHOIDAL SLOT
In Cycle 241 "Single-Fluted Deep-Hole Drilling" it is now possible to
define a dwell depth (see “SINGLE-FLUTED DEEP-HOLE DRILLING
The approach and departure behavior of Cycle 39 "Cylinder Surface
Contour" can now be adjusted (see “Cycle run” on page 230)
New touch probe cycle for calibration of a touch probe on a
calibration sphere (see “CALIBRATE TS (Cycle 460, DIN/ISO:
G460)” on page 458)
KinematicsOpt: An additional parameter for determination of the
backlash in a rotary axis was introduced (see “Backlash” on page
473)
KinematicsOpt: Better support for positioning of Hirth-coupled axes
(see “Machines with Hirth-coupled axes” on page 469)
14
Cycle Functions Changed Since the Predecessor Versions
340 422-xx/340 423-xx
Cycle Functions Changed Since
the Predecessor Versions
340 422-xx/340 423-xx
The management of more than one block of calibration data was
changed (see Conversational Programming User's Manual).

Changed Cycle Functions of Software 34049x-05
Changed Cycle Functions of
Software 34049x-05
The cylindrical surface cycles 27, 28, 29 and 39 can now also be
used with modulo rotary axes. In the past, Machine Parameter 810.x
= 0 was required.
Cycle 403 does not check whether touch points and compensation
axis match. As a result, probing is also possible in a tilted coordinate
system (see “BASIC ROTATION Compensation via Rotary Axis
16
Changed Cycle Functions of Software 340 49x-06
Changed Cycle Functions of
Software 340 49x-06
The approach behavior during side finishing with Cycle 24 (DIN/ISO:
G124) was changed (see “Please note while programming:” on
page 199)

Changed Cycle Functions of Software 340 49x-06
18
Contents Fundamentals / Overviews
1
Using Cycles
2
Fixed Cycles: Drilling
3
Fixed Cycles: Tapping / Thread Milling
4
Fixed Cycles: Pocket Milling / Stud
Milling / Slot Milling 5
Fixed Cycles: Pattern Definitions
6
Fixed Cycles: Contour Pocket
7
Fixed Cycles: Cylindrical Surface
8
Fixed Cycles: Contour Pocket with
Contour Formula 9
Fixed Cycles: Multipass Milling
10
Cycles: Coordinate Transformations
11
Cycles: Special Functions
12
Using Touch Probe Cycles
13
Touch Probe Cycles: Automatic Measure-
ment of Workpiece Misalignment 14
Touch Probe Cycles: Automatic Datum
Setting 15
Touch Probe Cycles: Automatic
Workpiece Inspection 16
Touch Probe Cycles: Special Functions
17
Touch Probe Cycles: Automatic
Kinematics Measurement 18
Touch Probe Cycles: Automatic Tool
Measurement 19

1 Fundamentals / Overviews ..... 43
1.1 Introduction ..... 44
1.2 Available Cycle Groups ..... 45
Overview of fixed cycles ..... 45
Overview of touch probe cycles ..... 46

2 Using Fixed Cycles ..... 47
2.1 Working with Fixed Cycles ..... 48
Machine-specific cycles ..... 48
Defining a cycle using soft keys ..... 49
Defining a cycle using the GOTO function ..... 49
Calling cycles ..... 50
Working with the secondary axes U/V/W ..... 52
2.2 Program Defaults for Cycles ..... 53
Overview ..... 53
Entering GLOBAL DEF ..... 54
Using GLOBAL DEF information ..... 54
Global data valid everywhere ..... 55
Global data for drilling operations ..... 55
Global data for milling operations with pocket cycles 25x ..... 56
Global data for milling operations with contour cycles ..... 56
Global data for positioning behavior ..... 56
Global data for probing functions ..... 57
2.3 Pattern Definition PATTERN DEF ..... 58
Application ..... 58
Entering PATTERN DEF ..... 59
Using PATTERN DEF ..... 59
Defining individual machining positions ..... 60
Defining a single row ..... 61
Defining a single pattern ..... 62
Defining individual frames ..... 63
Defining a full circle ..... 64
Defining a circular arc ..... 65
2.4 Point Tables ..... 66
Function ..... 66
Creating a point table ..... 66
Hiding single points from the machining process ..... 67
Selecting a point table in the program ..... 68
Calling a cycle in connection with point tables ..... 69
22
3 Fixed Cycles: Drilling ..... 71
3.1 Basics ..... 72
Overview ..... 72
3.2 CENTERING (Cycle 240, DIN/ISO: G240) ..... 73
Cycle run ..... 73
Please note while programming: ..... 73
Cycle parameters ..... 74
3.3 DRILLING (Cycle 200) ..... 75
Cycle run ..... 75
3.4 REAMING (Cycle 201, DIN/ISO: G201) ..... 77
Cycle run ..... 77
3.5 BORING (Cycle 202, DIN/ISO: G202) ..... 79
Cycle run ..... 79
3.6 UNIVERSAL DRILLING (Cycle 203, DIN/ISO: G203) ..... 83
Cycle run ..... 83
3.7 BACK BORING (Cycle 204, DIN/ISO: G204) ..... 87
Cycle run ..... 87
3.8 UNIVERSAL PECKING (Cycle 205, DIN/ISO: G205) ..... 91
Cycle run ..... 91
3.9 BORE MILLING (Cycle 208) ..... 95
Cycle run ..... 95
3.10 SINGLE-FLUTED DEEP-HOLE DRILLING (Cycle 241, DIN/ISO: G241) ..... 98
Cycle run ..... 98
3.11 Programming Examples ..... 101

4 Fixed Cycles: Tapping / Thread Milling ..... 105
4.1 Basics ..... 106
Overview ..... 106
4.2 TAPPING NEW with a Floating Tap Holder (Cycle 206, DIN/ISO: G206) ..... 107
Cycle run ..... 107
4.3 RIGID TAPPING without a Floating Tap Holder NEW (Cycle 207, DIN/ISO: G207) ..... 109
Cycle run ..... 109
4.4 TAPPING WITH CHIP BREAKING (Cycle 209, DIN/ISO: G209) ..... 112
Cycle run ..... 112
4.5 Fundamentals of Thread Milling ..... 115
Prerequisites ..... 115
4.6 THREAD MILLING (Cycle 262, DIN/ISO: G262) ..... 117
Cycle run ..... 117
4.7 THREAD MILLING/COUNTERSINKING (Cycle 263, DIN/ISO: G263) ..... 120
Cycle run ..... 120
4.8 THREAD DRILLING/MILLING (Cycle 264, DIN/ISO: G264) ..... 124
Cycle run ..... 124
4.9 HELICAL THREAD DRILLING/MILLING (Cycle 265, DIN/ISO: G265) ..... 128
Cycle run ..... 128
4.10 OUTSIDE THREAD MILLING (Cycle 267, DIN/ISO: G267) ..... 132
Cycle run ..... 132
24
5 Fixed Cycles: Pocket Milling / Stud Milling / Slot Milling ..... 139
5.1 Basics ..... 140
Overview ..... 140
5.2 RECTANGULAR POCKET (Cycle 251, DIN/ISO: G251) ..... 141
Cycle run ..... 141
5.3 CIRCULAR POCKET (Cycle 252, DIN/ISO: G252) ..... 146
Cycle run ..... 146
5.4 SLOT MILLING (Cycle 253, DIN/ISO: G253) ..... 150
Cycle run ..... 150
5.5 CIRCULAR SLOT (Cycle 254, DIN/ISO: G254) ..... 155
Cycle run ..... 155
5.6 RECTANGULAR STUD (Cycle 256, DIN/ISO: G256) ..... 160
Cycle run ..... 160
5.7 CIRCULAR STUD (Cycle 257, DIN/ISO: G257) ..... 164
Cycle run ..... 164

6 Fixed Cycles: Pattern Definitions ..... 171
6.1 Fundamentals ..... 172
Overview ..... 172
6.2 CIRCULAR PATTERN (Cycle 220, DIN/ISO: G220) ..... 173
Cycle run ..... 173
6.3 LINEAR PATTERN (Cycle 221, DIN/ISO: G221) ..... 176
Cycle run ..... 176
26
7 Fixed Cycles: Contour Pocket, Contour Trains ..... 181
7.1 SL Cycles ..... 182
Fundamentals ..... 182
Overview ..... 184
7.2 CONTOUR GEOMETRY (Cycle 14, DIN/ISO: G37) ..... 185
7.3 Overlapping Contours ..... 186
Basics ..... 186
Subprograms: overlapping pockets ..... 187
Area of inclusion ..... 188
Area of exclusion ..... 189
Area of intersection ..... 189
7.4 CONTOUR DATA (Cycle 20, DIN/ISO: G120) ..... 190
7.5 PILOT DRILLING (Cycle 21, DIN/ISO: G121) ..... 192
Cycle run ..... 192
7.6 ROUGH-OUT (Cycle 22, DIN/ISO: G122) ..... 194
Cycle run ..... 194
7.7 FLOOR FINISHING (Cycle 23, DIN/ISO: G123) ..... 198
Cycle run ..... 198
7.8 SIDE FINISHING (Cycle 24, DIN/ISO: G124) ..... 199
Cycle run ..... 199
7.9 CONTOUR TRAIN (Cycle 25, DIN/ISO: G125) ..... 201
Cycle run ..... 201
7.10 CONTOUR DATA (Cycle 270, DIN/ISO: G270) ..... 203
7.11 TROCHOIDAL SLOT (Cycle 275, DIN/ISO: G275) ..... 205
Cycle run ..... 205

8 Fixed Cycles: Cylindrical Surface ..... 219
8.1 Basics ..... 220
Overview of cylindrical surface cycles ..... 220
8.2 CYLINDER SURFACE (Cycle 27, DIN/ISO: G127, Software Option 1) ..... 221
Execution of cycle ..... 221
8.3 CYLINDER SURFACE Slot Milling (Cycle 28, DIN/ISO: G128, Software Option 1) ..... 224
Cycle run ..... 224
8.4 CYLINDER SURFACE Ridge Milling (Cycle 29, DIN/ISO: G129, Software Option 1) ..... 227
Cycle run ..... 227
8.5 CYLINDER SURFACE Outside Contour Milling (Cycle 39, DIN/ISO: G139, Software Option 1) ..... 230
Cycle run ..... 230
28
9 Fixed Cycles: Contour Pocket with Contour Formula ..... 237
9.1 SL Cycles with Complex Contour Formula ..... 238
Basics ..... 238
Selecting a program with contour definitions ..... 240
Defining contour descriptions ..... 241
Entering a complex contour formula ..... 242
Overlapping contours ..... 243
Contour machining with SL Cycles ..... 245
9.2 SL Cycles with Simple Contour Formula ..... 249
Entering a simple contour formula ..... 251
Contour machining with SL Cycles ..... 251

10 Fixed Cycles: Multipass Milling ..... 253
10.1 Basics ..... 254
Overview ..... 254
10.2 RUN 3-D DATA (Cycle 30, DIN/ISO: G60) ..... 255
Cycle run ..... 255
10.3 MULTIPASS MILLING (Cycle 230, DIN/ISO: G230) ..... 257
Cycle run ..... 257
10.4 RULED SURFACE (Cycle 231, DIN/ISO: G231) ..... 259
Cycle run ..... 259
10.5 FACE MILLING (Cycle 232, DIN/ISO: G232) ..... 263
Cycle run ..... 263
30
11 Cycles: Coordinate Transformations ..... 271
Overview ..... 272
Effect of coordinate transformations ..... 273
11.2 DATUM SHIFT (Cycle 7, DIN/ISO: G54) ..... 274
Effect ..... 274
11.3 DATUM Shift with Datum Tables (Cycle 7, DIN/ISO: G53) ..... 275
Effect ..... 275
Selecting a datum table in the part program ..... 277
Editing the datum table in the Programming and Editing mode of operation ..... 278
Editing a pocket table in a Program Run operating mode ..... 279
Transferring the actual values into the datum table ..... 279
Configuring the datum table ..... 280
To exit a datum table ..... 280
11.4 DATUM SETTING (Cycle 247, DIN/ISO: G247) ..... 281
Effect ..... 281
Please note before programming: ..... 281
11.5 MIRROR IMAGE (Cycle 8, DIN/ISO: G28) ..... 282
Effect ..... 282
11.6 ROTATION (Cycle 10, DIN/ISO: G73) ..... 284
Effect ..... 284
11.7 SCALING (Cycle 11, DIN/ISO: G72) ..... 286
Effect ..... 286
11.8 AXIS-SPECIFIC SCALING (Cycle 26) ..... 288
Effect ..... 288

11.9 WORKING PLANE (Cycle 19, DIN/ISO: G80, Software Option 1) ..... 290
Effect ..... 290
Resetting ..... 292
Positioning the axes of rotation ..... 293
Position display in the tilted system ..... 295
Workspace monitoring ..... 295
Positioning in a tilted coordinate system ..... 295
Combining coordinate transformation cycles ..... 296
Automatic workpiece measurement in the tilted system ..... 296
Procedure for working with Cycle 19 WORKING PLANE ..... 297
32
12 Cycles: Special Functions ..... 301
Overview ..... 302
12.2 DWELL TIME (Cycle 9, DIN/ISO: G04) ..... 303
Function ..... 303
12.3 PROGRAM CALL (Cycle 12, DIN/ISO: G39) ..... 304
Cycle function ..... 304
12.4 ORIENTED SPINDLE STOP (Cycle 13, DIN/ISO: G36) ..... 306
12.5 TOLERANCE (Cycle 32, DIN/ISO: G62) ..... 307
Influences of the geometry definition in the CAM system ..... 308

13 Using Touch Probe Cycles ..... 311
13.1 General Information about Touch Probe Cycles ..... 312
Method of function ..... 312
Cycles in the Manual and El. Handwheel modes ..... 313
Touch probe cycles for automatic operation ..... 313
13.2 Before You Start Working with Touch Probe Cycles ..... 315
Maximum traverse to touch point: MP6130 ..... 315
Safety clearance to touch point: MP6140 ..... 315
Orient the infrared touch probe to the programmed probe direction: MP6165 ..... 315
Consider a basic rotation in the Manual Operation mode: MP6166 ..... 316
Multiple measurement: MP6170 ..... 316
Confidence interval for multiple measurement: MP6171 ..... 316
Touch trigger probe, probing feed rate: MP6120 ..... 317
Touch trigger probe, rapid traverse for positioning: MP6150 ..... 317
Touch trigger probe, rapid traverse for positioning: MP6151 ..... 317
KinematicsOpt: Tolerance limit in Optimization mode: MP6600 ..... 317
KinematicsOpt, permissible deviation of the calibration ball radius: MP6601 ..... 317
Executing touch probe cycles ..... 318
34
14 Touch Probe Cycles: Automatic Measurement of Workpiece Misalignment ..... 319
Overview ..... 320
Characteristics common to all touch probe cycles for measuring workpiece misalignment ..... 321
14.2 BASIC ROTATION (Cycle 400, DIN/ISO: G400) ..... 322
Cycle run ..... 322
14.3 BASIC ROTATION from Two Holes (Cycle 401, DIN/ISO: G401) ..... 325
Cycle run ..... 325
14.4 BASIC ROTATION over Two Studs (Cycle 402, DIN/ISO: G402) ..... 328
Cycle run ..... 328
14.5 BASIC ROTATION Compensation via Rotary Axis (Cycle 403, DIN/ISO: G403) ..... 331
Cycle run ..... 331
14.6 SET BASIC ROTATION (Cycle 404, DIN/ISO: G404) ..... 335
Cycle run ..... 335
14.7 Compensating Workpiece Misalignment by Rotating the C Axis (Cycle 405, DIN/ISO: G405) ..... 336
Cycle run ..... 336

15 Touch Probe Cycles: Automatic Datum Setting ..... 341
Overview ..... 342
Characteristics common to all touch probe cycles for datum setting ..... 343
15.2 SLOT CENTER REF PT (Cycle 408, DIN/ISO: G408, FCL 3 Function) ..... 345
Cycle run ..... 345
15.3 RIDGE CENTER REF PT (Cycle 409, DIN/ISO: G409, FCL 3 function) ..... 349
Cycle run ..... 349
15.4 DATUM FROM INSIDE OF RECTANGLE (Cycle 410, DIN/ISO: G410) ..... 352
Cycle run ..... 352
15.5 DATUM FROM OUTSIDE OF RECTANGLE (Cycle 411, DIN/ISO: G411) ..... 356
Cycle run ..... 356
15.6 DATUM FROM INSIDE OF CIRCLE (Cycle 412, DIN/ISO: G412) ..... 360
Cycle run ..... 360
15.7 DATUM FROM OUTSIDE OF CIRCLE (Cycle 413, DIN/ISO: G413) ..... 364
Cycle run ..... 364
15.8 DATUM FROM OUTSIDE OF CORNER (Cycle 414, DIN/ISO: G414) ..... 368
Cycle run ..... 368
15.9 DATUM FROM INSIDE OF CORNER (Cycle 415, DIN/ISO: G415) ..... 373
Cycle run ..... 373
36
15.10 DATUM CIRCLE CENTER (Cycle 416, DIN/ISO: G416) ..... 377
Cycle run ..... 377
15.11 DATUM IN TOUCH PROBE AXIS (Cycle 417, DIN/ISO: G417) ..... 381
Cycle run ..... 381
15.12 DATUM AT CENTER OF 4 HOLES (Cycle 418, DIN/ISO: G418) ..... 383
Cycle run ..... 383
15.13 DATUM IN ONE AXIS (Cycle 419, DIN/ISO: G419) ..... 387
Cycle run ..... 387

16 Touch Probe Cycles: Automatic Workpiece Inspection ..... 395
Overview ..... 396
Recording the results of measurement ..... 397
Measurement results in Q parameters ..... 399
Classification of results ..... 399
Tolerance monitoring ..... 400
Tool monitoring ..... 400
Reference system for measurement results ..... 401
16.2 REF. PLANE (Cycle 0, DIN/ISO: G55) ..... 402
Cycle run ..... 402
16.3 POLAR REFERENCE PLANE (Cycle 1) ..... 403
Cycle run ..... 403
16.4 MEASURE ANGLE (Cycle 420, DIN/ISO: G420) ..... 405
Cycle run ..... 405
16.5 MEASURE HOLE (Cycle 421, DIN/ISO: G421) ..... 408
Cycle run ..... 408
16.6 MEAS. CIRCLE OUTSIDE (Cycle 422, DIN/ISO: G422) ..... 412
Cycle run ..... 412
16.7 MEAS. RECTAN. INSIDE (Cycle 423, DIN/ISO: G423) ..... 416
Cycle run ..... 416
16.8 MEAS. RECTAN. OUTSIDE (Cycle 424, DIN/ISO: G424) ..... 420
Cycle run ..... 420
16.9 MEASURE INSIDE WIDTH (Cycle 425, DIN/ISO: G425) ..... 424
Cycle run ..... 424
38
16.10 MEASURE RIDGE WIDTH (Cycle 426, DIN/ISO: G426) ..... 427
Cycle run ..... 427
16.11 MEASURE COORDINATE (Cycle 427, DIN/ISO: G427) ..... 430
Cycle run ..... 430
16.12 MEAS. BOLT HOLE CIRC. (Cycle 430, DIN/ISO: G430) ..... 433
Cycle run ..... 433
16.13 MEASURE PLANE (Cycle 431, DIN/ISO: G431) ..... 437
Cycle run ..... 437

17 Touch Probe Cycles: Special Functions ..... 445
17.1 Basics ..... 446
Overview ..... 446
17.2 CALIBRATE TS (Cycle 2) ..... 447
Cycle run ..... 447
17.3 CALIBRATE TS LENGTH (Cycle 9) ..... 448
Cycle run ..... 448
17.4 MEASURING (Cycle 3) ..... 449
Cycle run ..... 449
17.5 MEASURING IN 3-D (Cycle 4, FCL 3 function) ..... 451
Cycle run ..... 451
17.6 MEASURE AXIS SHIFT (Touch Probe Cycle 440, DIN/ISO: G440) ..... 453
Cycle run ..... 453
17.7 FAST PROBING (Cycle 441, DIN/ISO: G441, FCL 2 Function) ..... 456
Cycle run ..... 456
17.8 CALIBRATE TS (Cycle 460, DIN/ISO: G460) ..... 458
Cycle run ..... 458
40
18 Touch Probe Cycles: Automatic Kinematics Measurement ..... 461
18.1 Kinematic Measurement with TS Touch Probes (Option KinematicsOpt) ..... 462
Overview ..... 462
18.2 Prerequisites ..... 463
18.3 SAVE KINEMATICS (Cycle 450, DIN/ISO: G450; Option) ..... 464
Cycle run ..... 464
Log function ..... 465
18.4 MEASURE KINEMATICS (Cycle 451, DIN/ISO: G451; Option) ..... 466
Cycle run ..... 466
Positioning direction ..... 468
Machines with Hirth-coupled axes ..... 469
Choice of number of measuring points ..... 470
Choice of the calibration sphere position on the machine table ..... 470
Notes on the accuracy ..... 471
Notes on various calibration methods ..... 472
Backlash ..... 473
Various modes (Q406) ..... 478
18.5 PRESET COMPENSATION (Cycle 452, DIN/ISO: G452, Option) ..... 482
Cycle run ..... 482
Adjustment of tool changer heads ..... 487
Drift Compensation ..... 489

19 Touch Probe Cycles: Automatic Tool Measurement ..... 493
Overview ..... 494
Differences between Cycles 31 to 33 and Cycles 481 to 483 ..... 495
Setting the machine parameters ..... 495
Entries in the tool table TOOL.T ..... 497
Display of the measurement results ..... 498
19.2 Calibrating the TT (Cycle 30 or 480, DIN/ISO: G480) ..... 499
Cycle run ..... 499
19.3 CALIBRATING THE WIRELESS TT 449 (Cycle 484, DIN/ISO: G484) ..... 500
Cycle run ..... 500
19.4 Measuring the Tool Length (Cycle 31 or 481, DIN/ISO: G481) ..... 501
Cycle run ..... 501
19.5 Measuring the Tool Radius (Cycle 32 or 482, ISO: G482) ..... 503
Cycle run ..... 503
19.6 Measuring Tool Length and Radius (Cycle 33 or 483, ISO: G483) ..... 505
Cycle run ..... 505
Overview ..... 509
Fixed cycles ..... 509
Touch probe cycles ..... 511
42
Fundamentals /
Overviews
1.1 Introduction
1.1 Introduction
Frequently recurring machining cycles that comprise several working
steps are stored in the TNC memory as standard cycles. Coordinate
transformations and several special functions are also available as
cycles.
Most cycles use Q parameters as transfer parameters. Parameters
with specific functions that are required in several cycles always have
the same number: For example, Q200 is always assigned the setup
clearance, Q202 the plunging depth, etc.
Danger of collision!
Cycles sometimes execute extensive operations. For
safety reasons, you should run a graphical program test
before machining.
If you use indirect parameter assignments in cycles with

numbers greater than 200 (e.g. Q210 = Q1), any change in
the assigned parameter (e.g. Q1) will have no effect after
the cycle definition. Define the cycle parameter (e.g. Q210)
directly in such cases.
If you define a feed-rate parameter for fixed cycles greater
than 200, then instead of entering a numerical value you
can use soft keys to assign the feed rate defined in the
TOOL CALL block (FAUTO soft key). You can also use the
feed-rate alternatives FMAX (rapid traverse), FZ (feed per
tooth) and FU (feed per rev), depending on the respective
cycle and the function of the feed-rate parameter.
Note that, after a cycle definition, a change of the FAUTO
feed rate has no effect, because internally the TNC
assigns the feed rate from the TOOL CALL block when
processing the cycle definition.
If you want to delete a block that is part of a cycle, the TNC
asks you whether you want to delete the whole cycle.
44 Fundamentals / Overviews
1.2 Available Cycle Groups
Overview of fixed cycles
U The soft-key row shows the available groups of
cycles.
Cycle group Soft key Page

Cycles for pecking, reaming, boring, and counterboring Page 72
Cycles for tapping, thread cutting and thread milling Page 106
Cycles for milling pockets, studs and slots Page 140
Cycles for producing point patterns, such as circular or linear hole patterns Page 172
SL (Subcontour List) cycles which allow the contour-parallel machining of relatively complex Page 184
contours consisting of several overlapping subcontours, cylinder surface interpolation
Cycles for multipass milling of flat or twisted surfaces Page 254
Coordinate transformation cycles which enable datum shift, rotation, mirror image, enlarging Page 272
and reducing for various contours
Special cycles such as dwell time, program call, oriented spindle stop and tolerance Page 302
U If required, switch to machine-specific fixed cycles.

These fixed cycles can be integrated by your machine
tool builder.

Overview of touch probe cycles
U The soft-key row shows the available groups of
cycles.
Cycle group Soft key Page

Cycles for automatic measurement and compensation of workpiece misalignment Page 320
Cycles for automatic workpiece presetting Page 342
Cycles for automatic workpiece inspection Page 396
Calibration cycles, special cycles Page 446
Cycles for automatic kinematics measurement Page 462
Cycles for automatic tool measurement (enabled by the machine tool builder) Page 494
U If required, switch to machine-specific touch probe

cycles. These touch probe cycles can be integrated
by your machine tool builder.
46 Fundamentals / Overviews
Using Fixed Cycles
2.1 Working with Fixed Cycles
Machine-specific cycles
In addition to the HEIDENHAIN cycles, many machine tool builders
offer their own cycles in the TNC. These cycles are available in a
separate cycle-number range:
Cycles 300 to 399
Machine-specific cycles that are to be defined through the CYCLE
DEF key
Cycles 500 to 599
Machine-specific touch probe cycles that are to be defined through
the TOUCH PROBE key
Refer to your machine manual for a description of the

specific function.
Sometimes, machine-specific cycles also use transfer parameters,

which HEIDENHAIN already used in the standard cycles. The TNC
executes DEF-active cycles as soon as they are defined (see also
”Calling cycles” on page 50). It executes CALL-active cycles only after
they have been called (see also ”Calling cycles” on page 50). When
DEF-active cycles and CALL-active cycles are used simultaneously, it
is important to prevent overwriting of transfer parameters already in
use. Use the following procedure:
U As a rule, always program DEF-active cycles before CALL-active
cycles
U If you do want to program a DEF-active cycle between the definition
and call of a CALL-active cycle, do it only if there is no common use
of specific transfer parameters
48 Using Fixed Cycles

Defining a cycle using soft keys
U The soft-key row shows the available groups of cycles
U Press the soft key for the desired group of cycles, for
example DRILLING for the drilling cycles
U Select the desired cycle, for example THREAD
MILLING. The TNC initiates the programming dialog
and asks all required input values. At the same time a
graphic of the input parameters is displayed in the
right screen window. The parameter that is asked for
in the dialog prompt is highlighted
U Enter all parameters requested by the TNC and
conclude each entry with the ENT key
U The TNC ends the dialog when all required data has
been entered
Defining a cycle using the GOTO function

U The soft-key row shows the available groups of cycles
U The TNC shows an overview of cycles in a pop-up

window
U Choose the desired cycle with the arrow keys, or
U Choose the desired cycle with CTRL and the arrow
keys (for pagewise scrolling), or
U Enter the cycle number and confirm it with the ENT
key. The TNC then initiates the cycle dialog as
described above
Example NC blocks
7 CYCL DEF 200 DRILLING
Q200=2 ;SETUP CLEARANCE
Q201=3 ;DEPTH
Q206=150 ;FEED RATE FOR PLNGNG
Q202=5 ;PLUNGING DEPTH
Q210=0 ;DWELL TIME AT TOP
Q203=+0 ;SURFACE COORDINATE
Q204=50 ;2ND SETUP CLEARANCE
Q211=0.25 ;DWELL TIME AT DEPTH

Calling cycles
Prerequisites
The following data must always be programmed before a
cycle call:
BLK FORM for graphic display (needed only for test
graphics)
Tool call
Direction of spindle rotation (M functions M3/M4)
Cycle definition (CYCL DEF)
For some cycles, additional prerequisites must be
observed. They are detailed in the descriptions for each
cycle.
The following cycles become effective automatically as soon as they

are defined in the part program. These cycles cannot and must not be
called:
Cycle 220 for point patterns on circles and Cycle 221 for point
patterns on lines
SL Cycle 14 CONTOUR GEOMETRY
SL Cycle 20 CONTOUR DATA
Cycle 32 TOLERANCE
Coordinate transformation cycles
Cycle 9 DWELL TIME
All touch probe cycles
You can call all other cycles with the functions described as follows.
Calling a cycle with CYCL CALL

The CYCL CALL function calls the most recently defined fixed cycle
once. The starting point of the cycle is the position that was
programmed last before the CYCL CALL block.
U To program the cycle call, press the CYCL CALL key
U Press the CYCL CALL M soft key to enter a cycle call
U If necessary, enter the miscellaneous function M (for
example M3 to switch the spindle on), or end the
dialog by pressing the END key
Calling a cycle with CYCL CALL PAT

The CYCL CALL PAT function calls the most recently defined fixed cycle
at all positions that you defined in a PATTERN DEF pattern definition
(see “Pattern Definition PATTERN DEF” on page 58) or in a point table
(see “Point Tables” on page 66).

Calling a cycle with CYCL CALL POS
The CYCL CALL POS function calls the most recently defined fixed cycle
once. The starting point of the cycle is the position that you defined in
the CYCL CALL POS block.
Using positioning logic the TNC moves o the position defined in the
CYCL CALL POS block.
If the current position in the tool axis is greater than the top surface
of the workpiece (Q203), the TNC moves the tool to the
programmed position first in the machining plane and then in the
tool axis
If the current tool position in the tool axis is below the top surface
of the workpiece (Q203), the TNC moves the tool to the
programmed position first in the tool axis to the clearance height and
then in the working plane to the programmed position
Three coordinate axes must always be programmed in the

CYCL CALL POS block. With the coordinate in the tool axis
you can easily change the starting position. It serves as an
additional datum shift.
The feed rate most recently defined in the CYCL CALL POS
block applies only for traverse to the start position
programmed in this block.
As a rule, the TNC moves without radius compensation
(R0) to the position defined in the CYCL CALL POS block.
If you use CYCL CALL POS to call a cycle in which a start
position is defined (for example Cycle 212), then the
position defined in the cycles serves as an additional shift
on the position defined in the CYCL CALL POS block. You
should therefore always define the start position to be set
in the cycle as 0.
Calling a cycle with M99/89

The M99 function, which is active only in the block in which it is
programmed, calls the last defined fixed cycle once. You can program
M99 at the end of a positioning block. The TNC moves to this position
and then calls the last defined fixed cycle.
If the TNC is to execute the cycle automatically after every positioning
block, program the first cycle call with M89 (depending on MP 7440).
To cancel the effect of M89, program:
M99 in the positioning block in which you move to the last starting
point, or
A CYCL CALL POS block or
A new fixed cycle with CYCL DEF

Working with the secondary axes U/V/W
The TNC performs infeed movements in the axis that was defined in
the TOOL CALL block as the spindle axis. It performs movements in
the working plane only in the principal axes X, Y or Z. Exceptions:
You program secondary axes for the side lengths in cycles 3 SLOT
MILLING and 4 POCKET MILLING
You program secondary axes in the first block of the contour
geometry subprogram of an SL cycle
In Cycles 5 (CIRCULAR POCKET), 251 (RECTANGULAR POCKET),
252 (CIRCULAR POCKET), 253 (SLOT) and 254 (CIRCULAR SLOT),
the TNC machines the cycle in the axes that you programmed in the
last positioning block before the cycle call. When tool axis Z is active,
the following combinations are permissible:
X/Y
X/V
U/Y
U/V

2.2 Program Defaults for Cycles
Overview
All Cycles 20 to 25, as well as all of those with numbers 200 or higher,
always use identical cycle parameters, such as the setup clearance
Q200, which you must enter for each cycle definition. The GLOBAL DEF
function gives you the possibility of defining these cycle parameters
once at the beginning of the program, so that they are effective
globally for all fixed cycles used in the program. In the respective fixed
cycle you then simply link to the value defined at the beginning of the
program.
The following GLOBAL DEF functions are available:
Machining pattern Soft key Page

GLOBAL DEF COMMON Page 55
Definition of generally valid cycle
parameters
GLOBAL DEF DRILLING Page 55

Definition of specific drilling cycle
parameters
GLOBAL DEF POCKET MILLING Page 56

Definition of specific pocket-milling cycle
parameters
GLOBAL DEF CONTOUR MILLING Page 56

Definition of specific contour milling
parameters
GLOBAL DEF POSITIONING Page 56

Definition of the positioning behavior for
CYCL CALL PAT
GLOBAL DEF PROBING Page 57

Definition of specific touch probe cycle
parameters

Entering GLOBAL DEF
U Select the Programming and Editing operating mode.
U Press the Special Functions key.
U Select the functions for program defaults.
U Select GLOBAL DEF functions.
U Select the desired GLOBAL DEF function, e.g. GLOBAL

DEF COMMON
U Enter the required definitions, and confirm each entry
with the ENT key.
Using GLOBAL DEF information

If you have entered the corresponding GLOBAL DEF functions at the
beginning of the program, then you can link to these globally valid
values when defining any fixed cycle.
Proceed as follows:
U Select the Programming and Editing operating mode
U Select fixed cycles
U Select the desired group of cycles, for example:

drilling cycles
U Select the desired cycle, e.g. DRILLING
U The TNC displays the SET STANDARD VALUES soft
key, if there is a global parameter for it
U Press the SET STANDARD VALUES soft key. The TNC
enters the word PREDEF (predefined) in the cycle
definition. You have now created a link to the
corresponding GLOBAL DEF parameter that you defined
at the beginning of the program
Please note that later changes to the program settings
affect the entire machining program, and can therefore
change the machining procedure significantly.
If you enter a fixed value in a fixed cycle, then this value
will not be changed by the GLOBAL DEF functions.

Global data valid everywhere
U Setup clearance: Distance between tool tip and workpiece surface
for automated approach of the cycle start position in the tool axis
U 2nd set-up clearance: Position to which the TNC positions the tool
at the end of a machining step. The next machining position is
approached at this height in the machining plane
U F positioning: Feed rate at which the TNC traverses the tool within
a cycle
U F retraction: Feed rate at which the TNC retracts the tool
The parameters are valid for all fixed cycles with numbers
greater than 2xx.
Global data for drilling operations

U Retraction rate for chip breaking: Value by which the TNC
retracts the tool during chip breaking
U Dwell time at depth: Time in seconds that the tool remains at the
hole bottom
U Dwell time at top: Time in seconds that the tool remains at the
setup clearance
The parameters apply to the drilling, tapping and thread

milling cycles 200 to 209, 240, and 262 to 267.

Global data for milling operations with pocket
cycles 25x
U Overlap factor: The tool radius multiplied by the overlap factor
equals the lateral stepover
U Climb or up-cut: Select the type of milling
U Plunging type: Plunge into the material helically, in a reciprocating
motion, or vertically
The parameters apply to milling cycles 251 to 257.
Global data for milling operations with contour

cycles
U Setup clearance: Distance between tool tip and workpiece surface
for automated approach of the cycle start position in the tool axis
U Clearance height: Absolute height at which the tool cannot collide
with the workpiece (for intermediate positioning and retraction at
the end of the cycle)
U Overlap factor: The tool radius multiplied by the overlap factor
equals the lateral stepover
U Climb or up-cut: Select the type of milling
The parameters apply to SL cycles 20, 22, 23, 24 and 25.
Global data for positioning behavior

U Positioning behavior: Retraction in the tool axis at the end of the
machining step: Return to the 2nd setup clearance or to the position
at the beginning of the unit
The parameters apply to each fixed cycle that you call with
the CYCL CALL PAT function.

Global data for probing functions
U Setup clearance: Distance between stylus and workpiece surface
for automated approach of the probing position
U Clearance height: The coordinate in the touch probe axis to which
the TNC traverses the touch probe between measuring points, if the
Move to clearance height option is activated
U Move to clearance height: Select whether the TNC moves the
touch probe to the setup clearance or clearance height between the
measuring points
Applies to all Touch Probe Cycles 4xx.

2.3 Pattern Definition PATTERN DEF
Application
You use the PATTERN DEF function to easily define regular machining
patterns, which you can call with the CYCL CALL PAT function. As with
the cycle definitions, support graphics that illustrate the respective
input parameter are also available for pattern definitions.
PATTERN DEF is to be used only in connection with the tool

axis Z.
The following machining patterns are available:
Machining pattern Soft key Page

POINT Page 60
Definition of up to any 9 machining
positions
ROW Page 61
Definition of a single row, straight or
rotated
PATTERN Page 62
Definition of a single pattern, straight,
rotated or distorted
FRAME Page 63
Definition of a single frame, straight,
rotated or distorted
CIRCLE Page 64
Definition of a full circle
PITCH CIRCLE Page 65

Definition of a circular arc

Entering PATTERN DEF
U Select the Programming and Editing operating mode
U Press the Special Functions key
U Select the functions for contour and point machining
U Open a PATTERN DEF block
U Select the desired machining pattern, e.g. a single row

U Enter the required definitions, and confirm each entry
with the ENT key
Using PATTERN DEF

As soon as you have entered a pattern definition, you can call it with
the CYCL CALL PAT function (see “Calling a cycle with CYCL CALL
PAT” on page 50). The TNC then performs the most recently defined
machining cycle on the machining pattern you defined.
A machining pattern remains active until you define a new

one, or select a point table with the SEL PATTERN function.
You can use the mid-program startup function to select
any point at which you want to start or continue machining
(see User's Manual, Test Run and Program Run sections).

Defining individual machining positions
You can enter up to 9 machining positions. Confirm each

entry with the ENT key.
If you have defined a workpiece surface in Z not equal to
0, then this value is effective in addition to the workpiece
surface Q203 that you defined in the machining cycle.
U X coord. of machining position (absolute): Enter X Example: NC blocks

coordinate
10 L Z+100 R0 FMAX
U Y coord. of machining position (absolute): Enter Y
coordinate 11 PATTERN DEF
POS1 (X+25 Y+33.5 Z+0)
U Workpiece surface coordinate (absolute): Enter Z POS2 (X+50 Y+75 Z+0)
coordinate at which machining is to begin

Defining a single row

U Starting point in X (absolute): Coordinate of the Example: NC blocks

starting point of the row in the X axis
10 L Z+100 R0 FMAX
U Starting point in Y (absolute): Coordinate of the
starting point of the row in the Y axis 11 PATTERN DEF
ROW1 (X+25 Y+33.5 D+8 NUM5 ROT+0 Z+0)
U Spacing of machining positions (incremental):
Distance between the machining positions. You can
enter a positive or negative value
U Number of positions: Total number of machining
positions
U Rot. position of entire pattern (absolute): Angle
of rotation around the entered starting point.
Reference axis: Major axis of the active machining
plane (e.g. X for tool axis Z). You can enter a positive
or negative value
U Workpiece surface coordinate (absolute): Enter Z

Defining a single pattern

The Rotary pos. ref. ax. and Rotary pos. minor ax.
parameters are added to a previously performed rotated
position of the entire pattern.

starting point of the pattern in the X axis
10 L Z+100 R0 FMAX
starting point of the pattern in the Y axis 11 PATTERN DEF
PAT1 (X+25 Y+33.5 DX+8 DY+10 NUMX5
U Spacing of machining positions X (incremental): NUMY4 ROT+0 ROTX+0 ROTY+0 Z+0)
Distance between the machining positions in the X
direction. You can enter a positive or negative value
U Spacing of machining positions Y (incremental):
Distance between the machining positions in the Y
U Number of columns: Total number of columns in the
pattern
U Number of lines: Total number of rows in the pattern
of rotation by which the entire pattern is rotated
around the entered starting point. Reference axis:
Major axis of the active machining plane (e.g. X for
tool axis Z). You can enter a positive or negative value
U Rotary pos. ref. ax.: Angle of rotation around which
only the principal axis of the machining plane is
distorted with respect to the entered starting point.
You can enter a positive or negative value
U Rotary pos. minor ax.: Angle of rotation around
which only the minor axis of the machining plane is

Defining individual frames

The Rotary pos. ref. ax. and Rotary pos. minor ax.
parameters are added to a previously performed rotated
position of the entire pattern.

starting point of the frame in the X axis
10 L Z+100 R0 FMAX
starting point of the frame in the Y axis 11 PATTERN DEF
FRAME1 (X+25 Y+33.5 DX+8 DY+10 NUMX5
U Spacing of machining positions X (incremental): NUMY4 ROT+0 ROTX+0 ROTY+0 Z+0)
Distance between the machining positions in the X
U Spacing of machining positions Y (incremental):
Distance between the machining positions in the Y
U Number of columns: Total number of columns in the
pattern
U Number of lines: Total number of rows in the pattern
of rotation by which the entire pattern is rotated
around the entered starting point. Reference axis:
Major axis of the active machining plane (e.g. X for
tool axis Z). You can enter a positive or negative value
U Rotary pos. ref. ax.: Angle of rotation around which
only the principal axis of the machining plane is
U Rotary pos. minor ax.: Angle of rotation around
which only the minor axis of the machining plane is

Defining a full circle

U Bolt-hole circle center X (absolute): Coordinate of Example: NC blocks

the circle center in the X axis.
10 L Z+100 R0 FMAX
U Bolt-hole circle center Y (absolute): Coordinate of
the circle center in the Y axis. 11 PATTERN DEF
CIRC1 (X+25 Y+33 D80 START+45 NUM8 Z+0)
U Bolt-hole circle diameter: Diameter of the bolt-hole
circle.
U Starting angle: Polar angle of the first machining
position. Reference axis: Major axis of the active
machining plane (e.g. X for tool axis Z). You can enter
a positive or negative value.
positions on the circle.
coordinate at which machining is to begin.

Defining a circular arc

U Bolt-hole circle center X (absolute): Coordinate of Example: NC blocks

the circle center in the X axis.
10 L Z+100 R0 FMAX
U Bolt-hole circle center Y (absolute): Coordinate of
the circle center in the Y axis. 11 PATTERN DEF
PITCHCIRC1 (X+25 Y+33 D80 START+45 STEP30
U Bolt-hole circle diameter: Diameter of the bolt-hole NUM8 Z+0)
circle.
U Starting angle: Polar angle of the first machining
position. Reference axis: Major axis of the active
machining plane (e.g. X for tool axis Z). You can enter
a positive or negative value.
U Stepping angle/end angle: Incremental polar angle
between two machining positions. You can enter a
positive or negative value. As an alternative you can
enter the end angle (switch via soft key).
positions on the circle.
coordinate at which machining is to begin.

2.4 Point Tables
2.4 Point Tables
Function
You should create a point table whenever you want to run a cycle, or
several cycles in sequence, on an irregular point pattern.
If you are using drilling cycles, the coordinates of the working plane in
the point table represent the hole centers. If you are using milling
cycles, the coordinates of the working plane in the point table
represent the starting-point coordinates of the respective cycle (e.g.
center-point coordinates of a circular pocket). Coordinates in the
spindle axis correspond to the coordinate of the workpiece surface.
Creating a point table

Select the Programming and Editing mode of operation.
Press the PGM MGT key to call the file manager.
FILE NAME?
Enter the name and file type of the point table and
confirm your entry with the ENT key.
To select the unit of measure, press the MM or INCH

soft key. The TNC changes to the program blocks
window and displays an empty point table.
With the soft key INSERT LINE, insert new lines and
enter the coordinates of the desired machining
position.
Repeat the process until all desired coordinates have been entered.
With the soft keys X OFF/ON, Y OFF/ON, Z OFF/ON

(second soft-key row), you can specify which coordinates
you want to enter in the point table.

2.4 Point Tables
Hiding single points from the machining process
In the FADE column of the point table you can specify if the defined
point is to be hidden during the machining process.
In the table, select the point to be hidden.
Select the FADE column.
Activate hiding, or
Deactivate hiding.

2.4 Point Tables
Selecting a point table in the program
In the Programming and Editing mode of operation, select the
program for which you want to activate the point table:
Press the PGM CALL key to call the function for

selecting the point table.
Press the POINT TABLE soft key.
Press the WINDOW SELECTION soft key: The TNC

superimposes a window where you can select the
desired datum table.
Select a point table with the arrow keys or by mouse click and confirm
by pressing ENT: The TNC enters the complete path name in the SEL
PATTERN block.
Conclude this function with the END key.
Alternatively you can also enter the table name or the complete path
name of the table to be called directly via the keyboard.
Example NC block
7 SEL PATTERN “TNC:\DIRKT5\NUST35.PNT”

2.4 Point Tables
Calling a cycle in connection with point tables
With CYCL CALL PAT the TNC runs the point table that you
last defined (even if you defined the point table in a
program that was nested with CALL PGM).
If you want the TNC to call the last defined fixed cycle at the points
defined in a point table, then program the cycle call with CYCLE CALL
PAT:
U To program the cycle call, press the CYCL CALL key
U Press the CYCL CALL PAT soft key to call a point table
U Enter the feed rate at which the TNC is to move from
point to point (if you make no entry the TNC will move
at the last programmed feed rate; FMAX not valid)
U If required, enter a miscellaneous function M, then
confirm with the END key
The TNC retracts the tool to the safety clearance between the starting
points. Depending on which is greater, the TNC uses either the spindle
axis coordinate from the cycle call or the value from cycle parameter
Q204 as the safety clearance.
If you want to move at reduced feed rate when pre-positioning in the
spindle axis, use the miscellaneous function M103.
Effect of the point tables with SL cycles and Cycle 12

The TNC interprets the points as an additional datum shift.
Effect of the point tables with Cycles 200 to 208 and 262 to 267
The TNC interprets the points of the working plane as coordinates of
the hole centers. If you want to use the coordinate defined in the point
table for the spindle axis as the starting point coordinate, you must
define the workpiece surface coordinate (Q203) as 0.
Effect of the point tables with Cycles 210 to 215

The TNC interprets the points as an additional datum shift. If you want
to use the points defined in the point table as starting-point
coordinates, you must define the starting points and the workpiece
surface coordinate (Q203) in the respective milling cycle as 0.
Effect of the point tables with Cycles 251 to 254

The TNC interprets the points of the working plane as coordinates of
the cycle starting point. If you want to use the coordinate defined in
the point table for the spindle axis as the starting point coordinate, you
must define the workpiece surface coordinate (Q203) as 0.

2.4 Point Tables

Fixed Cycles: Drilling
3.1 Basics
3.1 Basics
Overview
The TNC offers 9 cycles for all types of drilling operations:
Cycle Soft key Page

240 CENTERING Page 73
With automatic pre-positioning, 2nd
set-up clearance, optional entry of the
centering diameter or centering depth
200 DRILLING Page 75

setup clearance
201 REAMING Page 77

setup clearance
202 BORING Page 79

setup clearance
203 UNIVERSAL DRILLING Page 83

setup clearance, chip breaking, and
decrementing
204 BACK BORING Page 87

setup clearance
205 UNIVERSAL PECKING Page 91

setup clearance, chip breaking, and
advanced stop distance
208 BORE MILLING Page 95

setup clearance
241 SINGLE-LIP DEEP-HOLE Page 98

DRILLING
With automatic pre-positioning to
deepened starting point, shaft speed
and coolant definition
72 Fixed Cycles: Drilling

3.2 CENTERING (Cycle 240, DIN/ISO: G240)
3.2 CENTERING (Cycle 240,
DIN/ISO: G240)
Cycle run
1 The TNC positions the tool in the spindle axis at rapid traverse FMAX
to the setup clearance above the workpiece surface.
2 The tool is centered at the programmed feed rate F to the entered
centering diameter or centering depth.
3 If defined, the tool remains at the centering depth.
4 Finally, the tool moves to setup clearance or—if programmed—to
the 2nd setup clearance at rapid traverse FMAX.
Please note while programming:
Program a positioning block for the starting point (hole

center) in the working plane with radius compensation R0.
The algebraic sign for the cycle parameter Q344 (diameter)
or Q201 (depth) determines the working direction. If you
program the diameter or depth = 0, the cycle will not be
executed.
Enter in MP7441 bit 2 whether the TNC should output an
error message (bit 2=1) or not (bit 2=0) if a positive depth
is entered.
Keep in mind that the TNC reverses the calculation for pre-
positioning when a positive diameter or depth is
entered. This means that the tool moves at rapid traverse
in the tool axis to setup clearance below the workpiece
surface!

3.2 CENTERING (Cycle 240, DIN/ISO: G240)
Cycle parameters
U Setup clearance Q200 (incremental): Distance
between tool tip and workpiece surface. Enter a
positive value. Input range 0 to 99999.9999, Z Q206
alternatively PREDEF
U Select Depth/Diameter (1/0) Q343: Select whether
centering is based on the entered diameter or depth. Q210
If the TNC is to center based on the entered diameter, Q200 Q204
the point angle of the tool must be defined in the T- Q203
ANGLE column of the tool table TOOL.T.
0: Centering based on the entered depth Q201
1: Centering based on the entered diameter Q344
U Depth Q201 (incremental value): Distance between

workpiece surface and centering bottom (tip of
centering taper). Only effective if Q343=0 is defined.
Input range –99999.9999 to 99999.9999 X
U Diameter (algebraic sign) Q344: Centering
diameter. Only effective if Q343=1 is defined. Input
range –99999.9999 to 99999.9999
U Feed rate for plunging Q206: Traversing speed of Y
the tool during centering in mm/min. Input range: 0 to
99999.999; alternatively FAUTO, FU.
50
U Dwell time at depth Q211: Time in seconds that the
tool remains at the hole bottom. Input range 0 to
3600.0000, alternatively PREDEF
U Workpiece surface coordinate Q203 (absolute): 20
Coordinate of the workpiece surface. Input range:
-99999.9999 to 99999.9999
U 2nd setup clearance Q204 (incremental): Coordinate X
in the spindle axis at which no collision between tool 30 80
and workpiece (fixtures) can occur. Input range 0 to
Example: NC blocks
10 L Z+100 R0 FMAX
11 CYCL DEF 240 CENTERING
Q343=1 ;SELECT DEPTH/DIA.
Q201=+0 ;DEPTH
Q344=-9 ;DIAMETER
12 CYCL CALL POS X+30 Y+20 Z+0 FMAX M3
13 CYCL CALL POS X+80 Y+50 Z+0 FMAX

3.3 DRILLING (Cycle 200)
Cycle run
2 The tool drills to the first plunging depth at the programmed feed
rate F.
3 The TNC returns the tool at FMAX to the setup clearance, dwells
there (if a dwell time was entered), and then moves at FMAX to the
setup clearance above the first plunging depth.
4 The tool then advances with another infeed at the programmed
feed rate F.
5 The TNC repeats this process (2 to 4) until the programmed depth
is reached.
6 The tool is retracted from the hole bottom to the setup clearance
or—if programmed—to the 2nd setup clearance at FMAX.

The algebraic sign for the cycle parameter DEPTH
determines the working direction. If you program
DEPTH = 0, the cycle will not be executed.
is entered.
positioning when a positive depth is entered. This
means that the tool moves at rapid traverse in the tool axis
to setup clearance below the workpiece surface!

Cycle parameters
between tool tip and workpiece surface. Enter a
positive value. Input range 0 to 99999.9999, Z Q206
U Depth Q201 (incremental): Distance between
workpiece surface and bottom of hole (tip of drill Q210
taper). Input range –99999.9999 to 99999.9999 Q200 Q204
Q203
U Feed rate for plunging Q206: Traversing speed of
the tool during drilling in mm/min. Input range: 0 to Q202
99999.999; alternatively FAUTO, FU. Q201
U Plunging depth Q202 (incremental): Infeed per cut.

Input range 0 to 99999.9999. The depth does not
have to be a multiple of the plunging depth. The TNC
will go to depth in one movement if:
X
The plunging depth is equal to the depth
The plunging depth is greater than the depth
U Dwell time at top Q210: Time in seconds that the
tool remains at setup clearance after having been Y
retracted from the hole for chip release. Input range 0
to 3600.0000, alternatively PREDEF
50
U Workpiece surface coordinate Q203 (absolute):
-99999.9999 to 99999.9999
U 2nd setup clearance Q204 (incremental): Coordinate 20
in the spindle axis at which no collision between tool
X
U Dwell time at depth Q211: Time in seconds that the 30 80
Example: NC blocks
11 CYCL DEF 200 DRILLING

Q201=-15 ;DEPTH
12 L X+30 Y+20 FMAX M3
13 CYCL CALL
14 L X+80 Y+50 FMAX M99

3.4 REAMING (Cycle 201, DIN/ISO: G201)
3.4 REAMING (Cycle 201,
DIN/ISO: G201)
Cycle run
to the entered setup clearance above the workpiece surface.
2 The tool reams to the entered depth at the programmed feed
rate F.
3 If programmed, the tool remains at the hole bottom for the entered
dwell time.
4 The tool then retracts to the setup clearance at the feed rate F, and
from there—if programmed—to the 2nd setup clearance at FMAX.

determines the working direction. If you program DEPTH
= 0, the cycle will not be executed.
is entered.

3.4 REAMING (Cycle 201, DIN/ISO: G201)
Cycle parameters
between tool tip and workpiece surface. Input range
0 to 99999.9999, alternatively PREDEF Z Q206
workpiece surface and bottom of hole. Input range:
-99999.9999 to 99999.9999
U Feed rate for plunging Q206: Traversing speed of Q200 Q204
Q203
the tool during reaming in mm/min. Input range: 0 to
Q201
tool remains at the hole bottom. Input range 0 to Q211
U Retraction feed rate Q208: Traversing speed of the
tool in mm/min when retracting from the hole. If you X
enter Q208 = 0, the tool retracts at the reaming feed
rate. Input range 0 to 99999.999
Coordinate of the workpiece surface. Input range 0 to Y
99999.9999
U 2nd setup clearance Q204 (incremental): Coordinate
in the spindle axis at which no collision between tool 50
20
X
30 80
Example: NC blocks
11 CYCL DEF 201 REAMING

Q201=-15 ;DEPTH
Q208=250 ;RETRACTION FEED RATE
12 L X+30 Y+20 FMAX M3
13 CYCL CALL
14 L X+80 Y+50 FMAX M9
15 L Z+100 FMAX M2

3.5 BORING (Cycle 202, DIN/ISO: G202)
3.5 BORING (Cycle 202, DIN/ISO:
G202)
Cycle run
2 The tool drills to the programmed depth at the feed rate for
plunging.
3 If programmed, the tool remains at the hole bottom for the entered
dwell time with active spindle rotation for cutting free.
4 The TNC then orients the spindle to the position that is defined in
parameter Q336.
5 If retraction is selected, the tool retracts in the programmed
direction by 0.2 mm (fixed value).
6 The TNC moves the tool at the retraction feed rate to the setup
clearance and then, if entered, to the 2nd setup clearance at FMAX.
If Q214=0, the tool point remains on the wall of the hole.

Machine and TNC must be specially prepared by the

machine tool builder for use of this cycle.
This cycle is effective only for machines with servo-
controlled spindle.

determines the working direction. If you program
DEPTH = 0, the cycle will not be executed.
After the cycle is completed, the TNC restores the coolant
and spindle conditions that were active before the cycle
call.
is entered.
Select a disengaging direction in which the tool moves
away from the edge of the hole.
Check the position of the tool tip when you program a
spindle orientation to the angle that you enter in Q336 (for
example, in the Positioning with Manual Data Input mode
of operation). Set the angle so that the tool tip is parallel to
a coordinate axis.
During retraction the TNC automatically takes an active
rotation of the coordinate system into account.

Cycle parameters
-99999.9999 to 99999.9999
the tool during boring at mm/min. Input range: 0 to Q203
Q201 Q208
tool remains at the hole bottom. Input range 0 to Q211
tool in mm/min when retracting from the hole. If you X
enter Q208 = 0, the tool retracts at feed rate for
plunging. Input range 0 to 99999.999, alternatively
FMAX, FAUTO, PREDEF
-99999.9999 to 99999.9999

U Disengaging direction (0/1/2/3/4) Q214:
Determine the direction in which the TNC retracts the
tool at the hole bottom (after spindle orientation). Y
0 Do not retract tool.
1 Retract tool in the negative ref. axis direction. 50
2 Retract tool in the negative minor axis direction.
3 Retract tool in the positive ref. axis direction.
4 Retract tool in the positive minor axis direction.
20
U Angle for spindle orientation Q336 (absolute):
Angle at which the TNC positions the tool before
retracting it. Input range -360.000 to 360.000
X
30 80
Example:
10 L Z+100 R0 FMAX
11 CYCL DEF 202 BORING
Q201=-15 ;DEPTH
Q214=1 ;DISENGAGING DIRECTN
Q336=0 ;ANGLE OF SPINDLE
12 L X+30 Y+20 FMAX M3
13 CYCL CALL
14 L X+80 Y+50 FMAX M99

3.6 UNIVERSAL DRILLING (Cycle 203, DIN/ISO: G203)
3.6 UNIVERSAL DRILLING
(Cycle 203, DIN/ISO: G203)
Cycle run
rate F.
3 If you have programmed chip breaking, the tool then retracts by
the entered retraction value. If you are working without chip
breaking, the tool retracts at the retraction feed rate to the setup
clearance, remains there—if programmed—for the entered dwell
time, and advances again at FMAX to the setup clearance above the
first PLUNGING DEPTH.
feed rate. If programmed, the plunging depth is decreased after
each infeed by the decrement.
5 The TNC repeats this process (2 to 4) until the programmed total
hole depth is reached.
6 The tool remains at the hole bottom—if programmed—for the
entered dwell time to cut free, and then retracts to the setup
clearance at the retraction feed rate. If programmed, the tool
moves to the 2nd setup clearance at FMAX.


is entered.

Cycle parameters
0 to 99999.9999, alternatively PREDEF Z Q206 Q208
workpiece surface and bottom of hole (tip of drill
taper). Input range -99999.9999 to 99999.9999 Q210
Q200 Q204
Q203
the tool during drilling in mm/min. Input range: 0 to
Q201
have to be a multiple of the plunging depth. The TNC Q211
the plunging depth is equal to the depth X
the plunging depth is greater than the depth and no
chip breaking is defined
U Dwell time at top Q210: Time in seconds that the
tool remains at setup clearance after having been
retracted from the hole for chip release. Input range
0 to 3600.0000, alternatively PREDEF
-99999.9999 to 99999.9999
U Decrement Q212 (incremental): Value by which the
TNC decreases the plunging depth Q202 after each
infeed. Input range 0 to 99999.9999

Example: NC blocks
U No. of breaks before retracting Q213: Number of
chip breaks after which the TNC is to withdraw the
tool from the hole for chip release. For chip breaking, 11 CYCL DEF 203 UNIVERSAL DRILLING
the TNC retracts the tool each time by the value in Q200=2 ;SETUP CLEARANCE
Q256. Input range 0 to 99999
Q201=-20 ;DEPTH
U Minimum plunging depth Q205 (incremental): If you
have entered a decrement, the TNC limits the Q206=150 ;FEED RATE FOR PLNGNG
plunging depth to the value entered with Q205. Input Q202=5 ;PLUNGING DEPTH
range 0 to 99999.9999
tool remains at the hole bottom. Input range 0 to Q203=+20 ;SURFACE COORDINATE
3600.0000, alternatively PREDEF Q204=50 ;2ND SETUP CLEARANCE
U Retraction feed rate Q208: Traversing speed of the Q212=0.2 ;DECREMENT
tool in mm/min when retracting from the hole. If you
Q213=3 ;BREAKS
enter Q208 = 0, the TNC retracts the tool at the feed
rate in Q206. Input range 0 to 99999.999, alternatively Q205=3 ;MIN. PLUNGING DEPTH
FMAX, FAUTO, PREDEF
U Retraction rate for chip breaking Q256 Q208=500 ;RETRACTION FEED RATE
(incremental): Value by which the TNC retracts the
tool during chip breaking. Input range 0.1000 to Q256=0.2 ;DIST. FOR CHIP BRKNG

3.7 BACK BORING (Cycle 204, DIN/ISO: G204)
3.7 BACK BORING (Cycle 204,
DIN/ISO: G204)
Cycle run
This cycle allows holes to be bored from the underside of the
workpiece. Z
2 The TNC then orients the spindle to the 0° position with an
oriented spindle stop, and displaces the tool by the off-center
distance.
3 The tool is then plunged into the already bored hole at the feed rate
for pre-positioning until the tooth has reached the setup clearance
on the underside of the workpiece.
4 The TNC then centers the tool again over the bore hole, switches
on the spindle and the coolant and moves at the feed rate for
boring to the depth of bore. X
5 If a dwell time is entered, the tool will pause at the top of the bore
hole and will then be retracted from the hole again. Another
oriented spindle stop is carried out and the tool is once again
displaced by the off-center distance.
6 The TNC moves the tool at the pre-positioning feed rate to the
setup clearance and then—if entered—to the 2nd setup clearance
at FMAX.


controlled spindle.
Special boring bars for upward cutting are required for this
cycle.

The algebraic sign for the cycle parameter depth
determines the working direction. Note: A positive sign
bores in the direction of the positive spindle axis.
The entered tool length is the total length to the underside
of the boring bar and not just to the tooth.
When calculating the starting point for boring, the TNC
considers the tooth length of the boring bar and the
thickness of the material.
You can also execute Cycle 204 with M04 if you have
programmed M04 instead of M03 prior to the cycle call.
Check the position of the tool tip when you program a
spindle orientation to the angle that you enter in Q336 (for
example, in the Positioning with Manual Data Input mode
of operation). Set the angle so that the tool tip is parallel to
a coordinate axis. Select a disengaging direction in which
the tool moves away from the edge of the hole.

Cycle parameters
between tool tip and workpiece surface. Input range Z
U Depth of counterbore Q249 (incremental):
Distance between underside of workpiece and
the top of the hole. A positive sign means the hole
will be bored in the positive spindle axis direction. Q204
Input range -99999.9999 to 99999.9999 Q200
U Material thickness Q250 (incremental): Thickness of

the workpiece. Input range 0.0001 to 99999.9999 Q250 Q203
U Off-center distance Q251 (incremental): Off-center Q249
distance for the boring bar; value from tool data sheet.
Q200 X
Input range 0.0001 to 99999.9999
U Tool edge height Q252 (incremental): Distance
between the underside of the boring bar and the main
cutting tooth; value from tool data sheet. Input range
0.0001 to 99999.9999 Q253
Z
U Feed rate for pre-positioning Q253: Traversing
speed of the tool in mm/min when plunging into the
workpiece, or when retracting from the workpiece. Q251
Input range 0 to 99999,999 alternatively FMAX, FAUTO,
PREDEF. Q252
U Feed rate for back boring Q254: Traversing speed

of the tool during back boring in mm/min. Input range:
0 to 99999.999; alternatively FAUTO, FU.
Q255
U Dwell time Q255: Dwell time in seconds at the top of
Q254
the bore hole. Input range 0 to 3600.000
X
Q214

Example: NC blocks
Coordinate of the workpiece surface. Input range
-99999.9999 to 99999.9999, alternatively PREDEF 11 CYCL DEF 204 BACK BORING
U 2nd setup clearance Q204 (incremental): Coordinate Q200=2 ;SETUP CLEARANCE

in the spindle axis at which no collision between tool Q249=+5 ;DEPTH OF COUNTERBORE
99999.9999 Q250=20 ;MATERIAL THICKNESS
U Disengaging direction (0/1/2/3/4) Q214: Q251=3.5 ;OFF-CENTER DISTANCE

Determine the direction in which the TNC displaces Q252=15 ;TOOL EDGE HEIGHT
the tool by the off-center distance (after spindle
orientation). Input of 0 is not permitted. Q253=750 ;F PRE-POSITIONING
Q254=200 ;F COUNTERSINKING
1 Retract tool in the negative ref. axis direction.
Q255=0 ;DWELL TIME
2 Retract tool in the negative minor axis direction.
3 Retract tool in the positive ref. axis direction. Q203=+20 ;SURFACE COORDINATE
4 Retract tool in the positive minor axis direction. Q204=50 ;2ND SETUP CLEARANCE
U Angle for spindle orientation Q336 (absolute): Q214=1 ;DISENGAGING DIRECTN
Angle at which the TNC positions the tool before it is Q336=0 ;ANGLE OF SPINDLE
plunged into or retracted from the bore hole. Input
range -360.0000 to 360.0000

3.8 UNIVERSAL PECKING (Cycle 205, DIN/ISO: G205)
3.8 UNIVERSAL PECKING (Cycle 205,
DIN/ISO: G205)
Cycle run
1 The TNC positions the tool in the tool axis at rapid traverse FMAX to
the programmed setup clearance above the workpiece surface.
2 If you enter a deepened starting point, the TNC moves at the
defined positioning feed rate to the setup clearance above the
deepened starting point.
rate F.
breaking, the tool is moved at rapid traverse to the setup
clearance, and then at FMAX to the entered starting position above
the first plunging depth.
feed rate. If programmed, the plunging depth is decreased after
each infeed by the decrement.
7 The tool remains at the hole bottom—if programmed—for the
entered dwell time to cut free, and then retracts to the setup
clearance at the retraction feed rate. If programmed, the tool


If you enter advance stop distances Q258 not equal to Q259,
the TNC will change the advance stop distances between
the first and last plunging depths at the same rate.
If you use Q379 to enter a deepened starting point, the TNC
merely changes the starting point of the infeed
movement. Retraction movements are not changed by
the TNC, therefore they are calculated with respect to the
coordinate of the workpiece surface.
is entered.

Cycle parameters
workpiece surface and bottom of hole (tip of drill
taper). Input range -99999.9999 to 99999.9999
Q203
Q201
have to be a multiple of the plunging depth. The TNC Q211
the plunging depth is equal to the depth X
the plunging depth is greater than the depth
-99999.9999 to 99999.9999
U Decrement Q212 (incremental): Value by which the
TNC decreases the plunging depth Q202. Input range
0 to 99999.9999
U Minimum plunging depth Q205 (incremental): If you
have entered a decrement, the TNC limits the
plunging depth to the value entered with Q205. Input
range 0 to 99999.9999
U Upper advanced stop distance Q258 (incremental):
Setup clearance for rapid traverse positioning when
the TNC moves the tool again to the current plunging
depth after retraction from the hole; value for the first
plunging depth. Input range 0 to 99999.9999
U Lower advanced stop distance Q259 (incremental):
depth after retraction from the hole; value for the last
plunging depth. Input range 0 to 99999.9999

Example: NC blocks
U Infeed depth for chip breaking Q257 (incremental):
Depth at which the TNC carries out chip breaking. No
chip breaking if 0 is entered. Input range 0 to 11 CYCL DEF 205 UNIVERSAL PECKING
99999.9999 Q200=2 ;SETUP CLEARANCE
U Retraction rate for chip breaking Q256 Q201=-80 ;DEPTH
tool during chip breaking. The TNC retracts the tool at Q206=150 ;FEED RATE FOR PLNGNG
a feed rate of 3000 mm/min. Input range 0.1000 to Q202=15 ;PLUNGING DEPTH
99999.9999, alternatively PREDEF.
tool remains at the hole bottom. Input range 0 to Q204=50 ;2ND SETUP CLEARANCE
3600.0000, alternatively PREDEF Q212=0.5 ;DECREMENT
U Deepened starting point Q379 (incremental with Q205=3 ;MIN. PLUNGING DEPTH
respect to the workpiece surface): Starting position of
Q258=0.5 ;UPPER ADV. STOP DIST.
drilling if a shorter tool has already pilot drilled to a
certain depth. The TNC moves at the feed rate for Q259=1 ;LOWER ADV. STOP DIST.
pre-positioning from the setup clearance to the
Q257=5 ;DEPTH FOR CHIP BRKNG
deepened starting point. Input range 0 to 99999.9999
Q256=0.2 ;DIST. FOR CHIP BRKNG
velocity of the tool during positioning from the setup Q211=0.25 ;DWELL TIME AT DEPTH
clearance to a deepened starting point in mm/min. Q379=7.5 ;STARTING POINT
Effective only if Q379 is entered not equal to 0. Input
range 0 to 99999.999, alternatively FMAX, FAUTO, Q253=750 ;F PRE-POSITIONING
PREDEF

3.9 BORE MILLING (Cycle 208)
Cycle run
to the programmed setup clearance above the workpiece surface
and then moves the tool to the bore hole circumference on a
rounded arc (if enough space is available).
2 The tool mills in a helix from the current position to the first
plunging depth at the programmed feed rate F.
3 When the drilling depth is reached, the TNC once again traverses
a full circle to remove the material remaining after the initial
plunge.
4 The TNC then positions the tool at the center of the hole again.
5 Finally the TNC returns to the setup clearance at FMAX. If
programmed, the tool moves to the 2nd setup clearance at FMAX.


If you have entered the bore hole diameter to be the same
as the tool diameter, the TNC will bore directly to the
entered depth without any helical interpolation.
An active mirror function does not influence the type of
milling defined in the cycle.
Note that if the infeed distance is too large, the tool or the
workpiece may be damaged.
To prevent the infeeds from being too large, enter the
maximum plunge angle of the tool in the ANGLE column of
the tool table. The TNC then automatically calculates the
max. infeed permitted and changes your entered value
accordingly.
is entered.

Cycle parameters
between tool lower edge and workpiece surface.
Input range 0 to 99999.9999, alternatively PREDEF Z
-99999.9999 to 99999.9999 Q204
U Feed rate for plunging Q206: Traversing speed of Q200
Q203
the tool during helical drilling in mm/min. Input range: Q334
0 to 99999.999; alternatively FAUTO, FU, FZ.
Q201
U Infeed per helix Q334 (incremental): Depth of the
tool plunge with each helix (=360°). Input range 0 to
99999.9999
Coordinate of the workpiece surface. Input range: X
-99999.9999 to 99999.9999
in the spindle axis at which no collision between tool Y
U Nominal diameter Q335 (absolute value): Bore-hole
Q206
diameter. If you have entered the nominal diameter to
be the same as the tool diameter, the TNC will bore
directly to the entered depth without any helical
Q335
interpolation. Input range 0 to 99999.9999
U Roughing diameter Q342 (absolute): As soon as you
enter a value greater than 0 in Q342, the TNC no
longer checks the ratio between the nominal
diameter and the tool diameter. This allows you to
rough-mill holes whose diameter is more than twice X
as large as the tool diameter. Input range 0 to
99999.9999
U Climb or up-cut Q351: Type of milling operation with Example: NC blocks
M3
+1 = climb milling 12 CYCL DEF 208 BORE MILLING
–1 = up-cut milling
PREDEF = use the default value from GLOBAL DEF
Q201=-80 ;DEPTH
Q334=1.5 ;PLUNGING DEPTH
Q335=25 ;NOMINAL DIAMETER
Q342=0 ;ROUGHING DIAMETER
Q351=+1 ;CLIMB OR UP-CUT

3.10 SINGLE-FLUTED DEEP-HOLE DRILLING (Cycle 241, DIN/ISO: G241)
3.10 SINGLE-FLUTED DEEP-HOLE
DRILLING (Cycle 241, DIN/ISO:
G241)
Cycle run
2 Then the TNC moves the tool at the defined positioning feed rate
to the setup clearance above the deepened starting point and
switches on the drilling speed (M3) and the coolant. The approach
motion is executed at the direction of rotation defined in the cycle,
with clockwise, counterclockwise or stationary spindle.
3 The tool drills to the entered drilling depth or, if defined so, to the
entered dwell depth, at the programmed feed rate F.
4 If programmed, the tool remains at the hole bottom for chip
breaking. Then the TNC switches off the coolant and resets the
drilling speed to the value defined for retraction.
5 After the dwell time at the hole bottom, the tool is retracted to the
setup clearance at the retraction feed rate. If programmed, the tool

is entered.

Cycle parameters
-99999.9999 to 99999.9999 Q208
Q379 Q201
U Dwell time at depth Q211: Time in seconds that the Q206
U Workpiece surface coordinate Q203 (absolute): Q211
-99999.9999 to 99999.9999
U Deepened starting point Q379 (incremental with
respect to the workpiece surface): Starting position
for actual drilling operation. The TNC moves at the
feed rate for pre-positioning from the setup
clearance to the deepened starting point. Input range
0 to 99999.9999
velocity of the tool during positioning from the setup
clearance to the deepened starting point in mm/min.
Effective only if Q379 is entered not equal to 0. Input
range 0 to 99999.999, alternatively FMAX, FAUTO,
PREDEF
tool in mm/min when retracting from the hole. If you
enter Q208 = 0, the TNC retracts the tool at the feed
rate in Q206. Input range 0 to 99999.999, alternatively
FMAX, FAUTO, PREDEF

Example: NC blocks
U Rotat. dir. of entry/exit (3/4/5) Q426: Desired
direction of spindle rotation when tool moves into and
retracts from the hole. Input range: 11 CYCL DEF 241 SINGLE-LIP DEEP-HOLE
3: Spindle rotation with M3 DRILLING
4: Spindle rotation with M4 Q200=2 ;SETUP CLEARANCE
5: Movement with stationary spindle
Q201=-80 ;DEPTH
U Spindle speed of entry/exit Q427: Desired spindle
speed when tool moves into and retracts from the Q206=150 ;FEED RATE FOR PLNGNG
hole Input range 0 to 99999 Q211=0.25 ;DWELL TIME AT DEPTH
U Drilling speed Q428: Desired speed for drilling Input Q203=+100 ;SURFACE COORDINATE
range 0 to 99999
U M function for coolant on? Q429: M function for
switching on the coolant The TNC switches the Q379=7.5 ;STARTING POINT
coolant on if the tool is in the hole at the deepened Q253=750 ;F PRE-POSITIONING
starting point Input range 0 to 999
U M function for coolant off? Q430: M function for
Q426=3 ;DIR. OF SPINDLE ROT.
switching off the coolant The TNC switches the
coolant off if the tool is at the hole depth. Input range Q427=25 ;ROT. SPEED INFEED/OUT
0 to 999
Q428=500 ;DRILLING SPEED
U Dwell depth Q435 (incremental): Coordinate in the Q429=8 ;COOLANT ON
spindle axis at which the tool is to dwell. If 0 is
entered, the function is not active (standard setting) Q430=9 ;COOLANT OFF
Application: During machining of through-holes some Q435=0 ;DWELL DEPTH
tools require a short dwell time before exiting the
bottom of the hole in order to transport the chips to
the top. Define a value smaller than the hole depth
Q201; input range 0 to 99999.9999.

3.11 Programming Examples
Example: Drilling cycles
Y
100
90
10
X
10 20 80 90 100
0 BEGIN PGM C200 MM

1 BLK FORM 0.1 Z X+0 Y+0 Z-20 Definition of workpiece blank
2 BLK FORM 0.2 X+100 Y+100 Z+0
3 TOOL CALL 1 Z S4500 Tool call (tool radius 3)
4 L Z+250 R0 FMAX Retract the tool
5 CYCL DEF 200 DRILLING Cycle definition
Q201=-15 ;DEPTH
Q206=250 ;FEED RATE FOR PLNGN
Q203=-10 ;SURFACE COORDINATE
Q204=20 ;2ND SET-UP CLEARANCE

6 L X+10 Y+10 R0 FMAX M3 Approach hole 1, spindle ON
7 CYCL CALL Cycle call
8 L Y+90 R0 FMAX M99 Approach hole 2, call cycle
9 L X+90 R0 FMAX M99 Approach hole 3, call cycle
10 L Y+10 R0 FMAX M99 Approach hole 4, call cycle
11 L Z+250 R0 FMAX M2 Retract in the tool axis, end program
12 END PGM C200 MM

Example: Using drilling cycles in connection with PATTERN DEF
The drill hole coordinates are stored in the

pattern definition PATTERN DEF POS and are called
by the TNC with CYCL CALL PAT:
Y
M6
The tool radii are selected so that all work steps
100
can be seen in the test graphics.
90
Program sequence
65
Centering (tool radius 4)
Drilling (tool radius 2.4) 55
Tapping (tool radius 3)

30
10
X
10 20 40 80 90 100
0 BEGIN PGM 1 MM
2 BLK FORM 0.2 X+100 Y+100 Y+0
3 TOOL CALL 1 Z S5000 Call the centering tool (tool radius 4)
4 L Z+10 R0 F5000 Move tool to clearance height (enter a value for F)
The TNC positions to the clearance height after every cycle
5 PATTERN DEF Define all drilling positions in the point pattern
POS1( X+10 Y+10 Z+0 )
POS2( X+40 Y+30 Z+0 )
POS3( X+20 Y+55 Z+0 )
POS4( X+10 Y+90 Z+0 )
POS5( X+90 Y+90 Z+0 )
POS6( X+80 Y+65 Z+0 )
POS7( X+80 Y+30 Z+0 )
POS8( X+90 Y+10 Z+0 )

6 CYCL DEF 240 CENTERING Cycle definition: CENTERING
Q343=0 ;SELECT DEPTH/DIA.
Q201=-2 ;DEPTH
Q344=-10 ;DIAMETER
Q211=0 ;DWELL TIME AT DEPTH
7 CYCL CALL PAT F5000 M13 Call the cycle in connection with point pattern
8 L Z+100 R0 FMAX Retract the tool, change the tool
9 TOOL CALL 2 Z S5000 Call the drilling tool (radius 2.4)
11 CYCL DEF 200 DRILLING Cycle definition: drilling
Q201=-25 ;DEPTH
Q206=150 ;FEED RATE FOR PECKING
14 TOOL CALL 3 Z S200 Call the tapping tool (radius 3)
15 L Z+50 R0 FMAX Move tool to clearance height
16 CYCL DEF 206 TAPPING NEW Cycle definition for tapping
Q201=-25 ;DEPTH OF THREAD
19 END PGM 1 MM

Fixed Cycles: Tapping /
Thread Milling
4.1 Basics
4.1 Basics
Overview
The TNC offers 8 cycles for all types of threading operations:
Cycle Soft key Page

206 TAPPING NEW Page 107
With a floating tap holder, with automatic
pre-positioning, 2nd setup clearance
207 RIGID TAPPING NEW Page 109

Without a floating tap holder, with
automatic pre-positioning, 2nd setup
clearance
209 TAPPING W/ CHIP BREAKING Page 112

Without a floating tap holder, with
automatic pre-positioning, 2nd setup
clearance, chip breaking
262 THREAD MILLING Page 117

Cycle for milling a thread in pre-drilled
material
263 THREAD MILLING/CNTSNKG Page 120

Cycle for milling a thread in pre-drilled
material and machining a countersunk
chamfer
264 THREAD DRILLING/MILLING Page 124

Cycle for drilling into the solid material
with subsequent milling of the thread
with a tool
265 HEL.THREAD DRILLING/MILLING Page 128

Cycle for milling the thread into the solid
material
267 OUTSIDE THREAD MILLING Page 128

Cycle for milling an external thread and
machining a countersunk chamfer
106 Fixed Cycles: Tapping / Thread Milling

4.2 TAPPING NEW with a Floating Tap Holder (Cycle 206, DIN/ISO: G206)
4.2 TAPPING NEW with a Floating
Tap Holder (Cycle 206, DIN/ISO:
G206)
Cycle run
2 The tool drills to the total hole depth in one movement.
3 Once the tool has reached the total hole depth, the direction of
spindle rotation is reversed and the tool is retracted to the setup
clearance at the end of the dwell time. If programmed, the tool
4 At the setup clearance, the direction of spindle rotation reverses
once again.

A floating tap holder is required for tapping. It must
compensate the tolerances between feed rate and spindle
speed during the tapping process.
When a cycle is being run, the spindle speed override knob
is disabled. The feed-rate override knob is active only
within a limited range, which is defined by the machine
tool builder (refer to your machine manual).
For tapping right-hand threads activate the spindle with M3,
for left-hand threads use M4.
is entered.

4.2 TAPPING NEW with a Floating Tap Holder (Cycle 206, DIN/ISO: G206)
Cycle parameters
between tool tip (at starting position) and workpiece
surface. Standard value: approx. 4 times the thread Z
pitch. Input range 0 to 99999.9999, alternatively Q206
PREDEF
U Total hole depth Q201 (thread length, incremental):
Distance between workpiece surface and end of Q204
thread. Input range -99999.9999 to 99999.9999 Q200
Q203
U Feed rate F Q206: Traversing speed of the tool during
tapping. Input range: 0 to 99999.999, alternatively Q201
FAUTO
U Dwell time at bottom Q211: Enter a value between 0
and 0.5 seconds to avoid wedging of the tool during Q211
retraction. Input range 0 to 3600.0000, alternatively
PREDEF X
Example: NC blocks
-99999.9999 to 99999.9999 25 CYCL DEF 206 TAPPING NEW
U 2nd setup clearance Q204 (incremental): Coordinate Q200=2 ;SETUP CLEARANCE
and workpiece (fixtures) can occur. Input range 0 to Q201=-20 ;DEPTH
99999.9999, alternatively PREDEF Q206=150 ;FEED RATE FOR PLNGNG
The feed rate is calculated as follows: F = S x p Q211=0.25 ;DWELL TIME AT DEPTH
F: Feed rate (mm/min) Q203=+25 ;SURFACE COORDINATE
S: Spindle speed (rpm) Q204=50 ;2ND SETUP CLEARANCE
p: Thread pitch (mm)
Retracting after a program interruption

If you interrupt program run during tapping with the machine stop
button, the TNC will display a soft key with which you can retract the
tool.

4.3 RIGID TAPPING without a Floating Tap Holder NEW (Cycle 207,
DIN/ISO: G207)
4.3 RIGID TAPPING without a
Floating Tap Holder NEW (Cycle
207, DIN/ISO: G207)
Cycle run
The TNC cuts the thread without a floating tap holder in one or more
passes.
2 The tool drills to the total hole depth in one movement.
3 Once the tool has reached the total hole depth, the direction of
spindle rotation is reversed and the tool is retracted to the setup
clearance at the end of the dwell time. If programmed, the tool
4 The TNC stops the spindle turning at setup clearance.

DIN/ISO: G207) Please note while programming:

controlled spindle.

The algebraic sign for the total hole depth parameter
determines the working direction.
The TNC calculates the feed rate from the spindle speed.
If the spindle speed override is used during tapping, the
feed rate is automatically adjusted.
The feed-rate override knob is disabled.
At the end of the cycle the spindle comes to a stop. Before
the next operation, restart the spindle with M3 (or M4).
is entered.

DIN/ISO: G207)
Cycle parameters
surface. Input range 0 to 99999.9999, alternatively
PREDEF Q239
U Total hole depth Q201 (incremental): Distance Z
between workpiece surface and end of thread. Input
range: -99999.9999 to 99999.9999 Q204
Q200
U Pitch Q239 Q203
Pitch of the thread. The algebraic sign differentiates
between right-hand and left-hand threads: Q201
+= right-hand thread
–= left-hand thread
Input range -99.9999 to 99.9999
X
-99999.9999 to 99999.9999
Example: NC blocks
in the spindle axis at which no collision between tool 26 CYCL DEF 207 RIGID TAPPING NEW
99999.9999, alternatively PREDEF Q200=2 ;SETUP CLEARANCE
Q201=-20 ;DEPTH
If you interrupt program run during thread cutting with the machine Q239=+1 ;PITCH
stop button, the TNC will display the MANUAL OPERATION soft key. Q203=+25 ;SURFACE COORDINATE
If you press the MANUAL OPERATION key, you can retract the tool
under program control. Simply press the positive axis direction button Q204=50 ;2ND SETUP CLEARANCE
of the active spindle axis.

4.4 TAPPING WITH CHIP BREAKING (Cycle 209, DIN/ISO: G209)
4.4 TAPPING WITH CHIP
BREAKING (Cycle 209,
DIN/ISO: G209)
Cycle run
The TNC machines the thread in several passes until it reaches the
programmed depth. You can define in a parameter whether the tool is
to be retracted completely from the hole for chip breaking.
1 The TNC positions the tool in the tool axis at rapid traverse FMAX to
the programmed setup clearance above the workpiece surface.
There it carries out an oriented spindle stop.
2 The tool moves to the programmed infeed depth, reverses the
direction of spindle rotation and retracts by a specific distance or
completely for chip breaking, depending on the definition. If you
have defined a factor for increasing the spindle speed, the TNC
retracts from the hole at the corresponding speed
3 It then reverses the direction of spindle rotation again and
advances to the next infeed depth.
4 The TNC repeats this process (2 to 3) until the programmed thread
depth is reached.
5 The tool is then retracted to the setup clearance. If programmed,
the tool moves to the 2nd setup clearance at FMAX.
6 The TNC stops the spindle turning at setup clearance.


controlled spindle.

The algebraic sign for the parameter thread depth
The TNC calculates the feed rate from the spindle speed.
If the spindle speed override is used during tapping, the
feed rate is automatically adjusted.
The feed-rate override knob is disabled.
If you defined an rpm factor for fast retraction in cycle
parameter Q403, the TNC limits the speed to the maximum
speed of the active gear range.
At the end of the cycle the spindle comes to a stop. Before
the next operation, restart the spindle with M3 (or M4).
is entered.

Cycle parameters
surface. Input range 0 to 99999.9999, alternatively
PREDEF Q239
U Thread depth Q201 (incremental): Distance between Z
workpiece surface and end of thread. Input range -
99999.9999 to 99999.9999 Q204
Q200
U Pitch Q239 Q203
Pitch of the thread. The algebraic sign differentiates
between right-hand and left-hand threads: Q201
Input range -99.9999 to 99.9999
X
-99999.9999 to 99999.9999
Example: NC blocks
in the spindle axis at which no collision between tool 26 CYCL DEF 209 TAPPING W/ CHIP BRKG
99999.9999, alternatively PREDEF Q200=2 ;SETUP CLEARANCE
U Infeed depth for chip breaking Q257 (incremental): Q201=-20 ;DEPTH
Depth at which TNC carries out chip breaking. Input Q239=+1 ;PITCH
range 0 to 99999.9999
U Retraction rate for chip breaking Q256: The TNC
multiplies the pitch Q239 by the programmed value Q204=50 ;2ND SETUP CLEARANCE
and retracts the tool by the calculated value during Q257=5 ;DEPTH FOR CHIP BRKNG
chip breaking. If you enter Q256 = 0, the TNC retracts
the tool completely from the hole (to the setup Q256=+25 ;DIST. FOR CHIP BRKNG
clearance) for chip breaking. Input range 0.1000 to Q336=50 ;ANGLE OF SPINDLE
99999.9999
Q403=1.5 ;RPM FACTOR
U Angle for spindle orientation Q336 (absolute):
Angle at which the TNC positions the tool before
machining the thread. This allows you to regroove the
thread, if required. Input range –360.0000 to
360.0000.
U RPM factor for retraction Q403: Factor by which
the TNC increases the spindle speed—and therefore
also the retraction feed rate—when retracting from
the drill hole. Input range 0.0001 to 10, rpm is
increased at most to the maximum speed of the
active gear range.

If you interrupt program run during thread cutting with the machine
stop button, the TNC will display the MANUAL OPERATION soft key.
If you press the MANUAL OPERATION key, you can retract the tool
under program control. Simply press the positive axis direction button
of the active spindle axis.

4.5 Fundamentals of Thread Milling
Prerequisites
Your machine tool should feature internal spindle cooling (cooling
lubricant at least 30 bars, compressed air supply at least 6 bars).
Thread milling usually leads to distortions of the thread profile. To
correct this effect, you need tool-specific compensation values
which are given in the tool catalog or are available from the tool
manufacturer. You program the compensation with the delta value
for the tool radius DR in the TOOL CALL.
The Cycles 262, 263, 264 and 267 can only be used with rightward
rotating tools. For Cycle 265 you can use rightward and leftward
rotating tools.
The working direction is determined by the following input
parameters: Algebraic sign Q239 (+ = right-hand thread / – = left-
hand thread) and milling method Q351 (+1 = climb / –1 = up-cut).
The table below illustrates the interrelation between the individual
input parameters for rightward rotating tools.
Climb/Up-
Internal thread Pitch Work direction
cut
Right-handed + +1(RL) Z+
Left-handed – –1(RR) Z+
Right-handed + –1(RR) Z–
Left-handed – +1(RL) Z–
Climb/Up-
External thread Pitch Work direction
cut
Right-handed + +1(RL) Z–
Left-handed – –1(RR) Z–
Right-handed + –1(RR) Z+
Left-handed – +1(RL) Z+
The TNC references the programmed feed rate during

thread milling to the tool cutting edge. Since the TNC,
however, always displays the feed rate relative to the path
of the tool tip, the displayed value does not match the
programmed value.
The machining direction of the thread changes if you
execute a thread milling cycle in connection with Cycle 8
MIRRORING in only one axis.

Always program the same algebraic sign for the infeeds:
Cycles comprise several sequences of operation that are
independent of each other. The order of precedence
according to which the work direction is determined is
described with the individual cycles. For example, if you
only want to repeat the countersinking process of a cycle,
enter 0 for the thread depth. The work direction will then
be determined from the countersinking depth.
Procedure in case of a tool break
If a tool break occurs during thread cutting, stop the
program run, change to the Positioning with MDI
operating mode and move the tool in a linear path to the
hole center. You can then retract the tool in the infeed axis
and replace it.

4.6 THREAD MILLING (Cycle 262, DIN/ISO: G262)
4.6 THREAD MILLING (Cycle 262,
DIN/ISO: G262)
Cycle run
to the entered setup clearance above the workpiece surface. Y
2 The tool moves at the programmed feed rate for pre-positioning to
the starting plane. The starting plane is derived from the algebraic
sign of the thread pitch, the milling method (climb or up-cut milling)
and the number of threads per step. Q207
3 The tool then approaches the thread diameter tangentially in a
helical movement. Before the helical approach, a compensating
Q335
motion of the tool axis is carried out in order to begin at the
programmed starting plane for the thread path.
4 Depending on the setting of the parameter for the number of
threads, the tool mills the thread in one helical movement, in
several offset movements or in one continuous movement.
5 After this, the tool departs the contour tangentially and returns to X
the starting point in the working plane.
6 At the end of the cycle, the TNC retracts the tool at rapid traverse
to the setup clearance, or—if programmed—to the 2nd setup
clearance.


The algebraic sign for the cycle parameter “thread depth”
determines the working direction. If you program the
thread DEPTH = 0, the cycle will not be executed.
The nominal thread diameter is approached in a semi-circle
from the center. A pre-positioning movement to the side
is carried out if the pitch of the tool diameter is four times
smaller than the nominal thread diameter.
Note that the TNC makes a compensation movement in
the tool axis before the approach movement. The length
of the compensation movement is at most half of the
thread pitch. Ensure sufficient space in the hole!
If you change the thread depth, the TNC automatically
changes the starting point for the helical movement.
is entered.

Cycle parameters
U Nominal diameter Q335: Nominal thread diameter.
Input range 0 to 99999.9999
Q239
U Thread pitch Q239: Pitch of the thread. The algebraic
sign differentiates between right-hand and left-hand Z Q253
threads:
– = left-hand thread Q200 Q204
Input range -99.9999 to 99.9999
U Thread depth Q201 (incremental): Distance between Q201
workpiece surface and root of thread. Input range -
99999.9999 to 99999.9999 Q203
U Threads per step Q355: Number of thread revolutions
by which the tool is moved: X
0 = one 360° helical line to the thread depth
1 = continuous helical path over the entire length of
the thread
>1 = several helical paths with approach and
departure; between them, the TNC offsets the tool by Q355 = 0 Q355 = 1 Q355 > 1
Q355, multiplied by the pitch. Input range 0 to 99999
workpiece, or when retracting from the workpiece.
Input range 0 to 99999.999 alternatively FMAX, FAUTO,
PREDEF.
U Climb or up-cut Q351: Type of milling operation with
M3
+1 = climb milling
Alternatively PREDEF
U Workpiece surface coordinate Q203 (absolute): Example: NC blocks
-99999.9999 to 99999.9999 25 CYCL DEF 262 THREAD MILLING
Q335=10 ;NOMINAL DIAMETER
in the spindle axis at which no collision between tool Q239=+1.5 ;PITCH
Q355=0 ;THREADS PER STEP
U Feed rate for milling Q207: Traversing speed of the
tool during milling in mm/min. Input range: 0 to Q253=750 ;F PRE-POSITIONING
99999.999, alternatively FAUTO. Q351=+1 ;CLIMB OR UP-CUT
Q207=500 ;FEED RATE FOR MILLING

4.7 THREAD MILLING/COUNTERSINKING (Cycle 263, DIN/ISO: G263)
4.7 THREAD
MILLING/COUNTERSINKING
Cycle run
Countersinking
2 The tool moves at the feed rate for pre-positioning to the
countersinking depth minus the setup clearance, and then at the
feed rate for countersinking to the countersinking depth.
3 If a setup clearance to the side has been entered, the TNC
immediately positions the tool at the feed rate for pre-positioning
to the countersinking depth.
4 Then, depending on the available space, the TNC makes a
tangential approach to the core diameter, either tangentially from
the center or with a pre-positioning move to the side, and follows
a circular path.
Countersinking at front
countersinking depth at front.
6 The TNC positions the tool without compensation from the center
on a semicircle to the offset at front, and then follows a circular
path at the feed rate for countersinking.
7 The TNC then moves in a semicircle to the hole center.
Thread milling
8 The TNC moves the tool at the programmed feed rate for pre-
positioning to the starting plane for the thread. The starting plane
is determined from the thread pitch and the type of milling (climb
or up-cut).
9 Then the tool moves tangentially on a helical path to the thread
diameter and mills the thread with a 360° helical motion.
10 After this, the tool departs the contour tangentially and returns to
11 At the end of the cycle, the TNC retracts the tool at rapid
traverse to the setup clearance, or—if programmed—to the
2nd setup clearance.

Before programming, note the following:

The algebraic sign of the cycle parameters depth of thread,
countersinking depth or sinking depth at front determines
the working direction. The working direction is defined in
the following sequence:
1st: Depth of thread
2nd: Countersinking depth
3rd: Depth at front
If you program a depth parameter to be 0, the TNC does
not execute that step.
If you want to countersink with the front of the tool, define
the countersinking depth as 0.
Program the thread depth as a value smaller than the
countersinking depth by at least one-third the thread pitch.
is entered.

Cycle parameters
Input range 0 to 99999.9999 Y
sign differentiates between right-hand and left-hand
threads:
Q207
– = left-hand thread
Input range -99.9999 to 99.9999
Q335
U Thread depth Q201 (incremental): Distance between
workpiece surface and root of thread. Input range -
99999.9999 to 99999.9999
U Countersinking depth Q356 (incremental): Distance
between tool point and the top surface of the X
workpiece. Input range -99999.9999 to 99999.9999
Input range 0 to 99999.999 alternatively FMAX, FAUTO, Q356
PREDEF. Q239
U Climb or up-cut Q351: Type of milling operation with Z

M3
Q253
+1 = climb milling
–1 = up-cut milling Q200 Q204
U Setup clearance Q200 (incremental): Distance Q201
0 to 99999.9999, alternatively PREDEF Q203
U Setup clearance to the side Q357 (incremental):

Distance between tool tooth and the wall of the hole.
X
U Depth at front Q358 (incremental): Distance
between tool tip and the top surface of the workpiece
for countersinking at the front of the tool. Input range Q359
-99999.9999 to 99999.9999
U Countersinking offset at front Q359 (incremental): Z
Distance by which the TNC moves the tool center
away from the hole center. Input range 0 to
99999.9999
Q358
X
Q357

Example: NC blocks

-99999.9999 to 99999.9999 25 CYCL DEF 263 THREAD MLLNG/CNTSNKG
U 2nd setup clearance Q204 (incremental): Coordinate Q335=10 ;NOMINAL DIAMETER

99999.9999, alternatively PREDEF Q201=-16 ;DEPTH OF THREAD
U Feed rate for countersinking Q254: Traversing Q356=-20 ;COUNTERSINKING DEPTH

speed of the tool during countersinking in mm/min. Q253=750 ;F PRE-POSITIONING
Input range: 0 to 99999.999, alternatively FAUTO, FU.
tool during milling in mm/min. Input range: 0 to
99999.9999, alternatively FAUTO. Q357=0.2 ;CLEARANCE TO SIDE
Q358=+0 ;DEPTH AT FRONT
Q359=+0 ;OFFSET AT FRONT

4.8 THREAD DRILLING/MILLING (Cycle 264, DIN/ISO: G264)
4.8 THREAD DRILLING/MILLING
Cycle run
Drilling
rate for plunging.
breaking, the tool is moved at rapid traverse to the setup
clearance, and then at FMAX to the entered starting position above
the first plunging depth.
feed rate.
Thread milling
positioning to the starting plane for the thread. The starting plane
is determined from the thread pitch and the type of milling (climb
or up-cut).
10 Then the tool moves tangentially on a helical path to the thread
diameter and mills the thread with a 360° helical motion.


The algebraic sign of the cycle parameters depth of thread,
countersinking depth or sinking depth at front determines
the working direction. The working direction is defined in
the following sequence:
2nd: Total hole depth
3rd: Depth at front
Program the thread depth as a value smaller than the total
hole depth by at least one-third the thread pitch.
is entered.

Cycle parameters
threads:
Q207
– = left-hand thread
Input range -99.9999 to 99.9999
Q335
U Thread depth Q201 (incremental): Distance
between workpiece surface and root of thread.
Input range -99999.9999 to 99999.9999
U Total hole depth Q356 (incremental): Distance
between workpiece surface and bottom of hole. Input X
range -99999.9999 to 99999.9999
Input range 0 to 99999,999 alternatively FMAX, FAUTO,
PREDEF. Q239
Q253
U Climb or up-cut Q351: Type of milling operation with Z
M3
+1 = climb milling
–1 = up-cut milling Q200 Q204
The depth does not have to be a multiple of the Q257
plunging depth. Input range 0 to 99999.9999. The Q203
TNC will go to depth in one movement if: Q201
The plunging depth is equal to the depth Q202 Q356 X
The plunging depth is greater than the depth
U Upper advanced stop distance Q258 (incremental):
depth after retraction from the hole. Input range 0 to
99999.9999
U Infeed depth for chip breaking Q257 (incremental):
Depth at which TNC carries out chip breaking. No chip
breaking if 0 is entered. Input range 0 to 99999.9999,
U Retraction rate for chip breaking Q256
tool during chip breaking. Input range 0.1000 to
99999.9999

for countersinking at the front of the tool. Input range
-99999.9999 to 99999.9999
Z
U Countersinking offset at front Q359 (incremental): Q359
away from the hole center. Input range 0 to
99999.9999
Q358
-99999.9999 to 99999.9999
Example: NC blocks
99999.9999, alternatively PREDEF 25 CYCL DEF 264 THREAD DRILLNG/MLLNG
U Feed rate for plunging Q206: Traversing speed of Q335=10 ;NOMINAL DIAMETER
the tool during drilling in mm/min. Input range: 0 to
99999.999; alternatively FAUTO, FU. Q239=+1.5 ;PITCH
U Feed rate for milling Q207: Traversing speed of the Q201=-16 ;DEPTH OF THREAD
tool during milling in mm/min. Input range: 0 to Q356=-20 ;TOTAL HOLE DEPTH
99999.9999, alternatively FAUTO.
Q253=750 ;F PRE-POSITIONING
Q258=0.2 ;ADVANCED STOP DISTANCE
Q257=5 ;DEPTH FOR CHIP BRKNG
Q256=0.2 ;DIST. FOR CHIP BRKNG
Q358=+0 ;DEPTH AT FRONT

4.9 HELICAL THREAD DRILLING/MILLING (Cycle 265, DIN/ISO: G265)
4.9 HELICAL THREAD
DRILLING/MILLING (Cycle 265,
DIN/ISO: G265)
Cycle run
2 If countersinking is before thread milling, the tool moves at the
feed rate for countersinking to the sinking depth at front. If
countersinking occurs after thread milling, the TNC moves the tool
to the countersinking depth at the feed rate for pre-positioning.
Thread milling
positioning to the starting plane for the thread.
helical movement.
7 The tool moves on a continuous helical downward path until it
reaches the thread depth.


The algebraic sign of the cycle parameters depth of thread
or sinking depth at front determines the working direction.
The working direction is defined in the following
sequence:
2nd: Depth at front
If you change the thread depth, the TNC automatically
changes the starting point for the helical movement.
The type of milling (up-cut/climb) is determined by the
thread (right-hand/left-hand) and the direction of tool
rotation, since it is only possible to work in the direction of
the tool.
is entered.

Cycle parameters
threads:
Q207
Input range -99.9999 to 99.9999
Q335
U Thread depth Q201 (incremental): Distance
between workpiece surface and root of thread.
Input range -99999.9999 to 99999.9999
speed of the tool in mm/min when plunging into the X
PREDEF.
for countersinking at the front of the tool. Input range Q239
-99999.9999 to 99999.9999 Z Q253
U Countersinking offset at front Q359 (incremental):
away from the hole center. Input range 0 to Q200 Q204
99999.9999
U Countersink Q360: Execution of the chamfer Q201
0 = before thread machining
1 = after thread machining Q203

X
Z
Q359
Q358

Example: NC blocks

-99999.9999 to 99999.9999 25 CYCL DEF 265 HEL. THREAD DRLG/MLG
U 2nd setup clearance Q204 (incremental): Coordinate Q335=10 ;NOMINAL DIAMETER

99999.9999, alternatively PREDEF Q201=-16 ;DEPTH OF THREAD
U Feed rate for countersinking Q254: Traversing Q253=750 ;F PRE-POSITIONING

speed of the tool during countersinking in mm/min. Q358=+0 ;DEPTH AT FRONT
Q360=0 ;COUNTERSINK
99999.999, alternatively FAUTO. Q200=2 ;SETUP CLEARANCE

4.10 OUTSIDE THREAD MILLING (Cycle 267, DIN/ISO: G267)
4.10 OUTSIDE THREAD MILLING
Cycle run
2 The TNC moves in the reference axis of the working plane from
the center of the stud to the starting point for countersinking at
front. The position of the starting point is determined by the thread
radius, tool radius and pitch.
5 The tool then moves on a semicircle to the starting point.
Thread milling
6 The TNC positions the tool to the starting point if there has been
no previous countersinking at front. Starting point for thread milling
= starting point for countersinking at front.
7 The tool moves at the programmed feed rate for pre-positioning to
the starting plane. The starting plane is derived from the algebraic
sign of the thread pitch, the milling method (climb or up-cut milling)
and the number of threads per step.
helical movement.
9 Depending on the setting of the parameter for the number of
threads, the tool mills the thread in one helical movement, in
several offset movements or in one continuous movement.

Program a positioning block for the starting point (stud

The offset required before countersinking at the front
should be determined ahead of time. You must enter the
value from the center of the stud to the center of the tool
(uncorrected value).
The algebraic sign of the cycle parameters depth of thread
or sinking depth at front determines the working direction.
The working direction is defined in the following
sequence:
2nd: Depth at front
The algebraic sign for the cycle parameter thread depth
is entered.

Cycle parameters
threads: Q207
Input range -99.9999 to 99.9999
Q335
U Thread depth Q201 (incremental): Distance between
workpiece surface and root of thread.
U Threads per step Q355: Number of thread revolutions
by which the tool is moved:
0 = one helical line to the thread depth X
1 = continuous helical path over the entire length of
the thread
>1 = several helical paths with approach and
departure; between them, the TNC offsets the tool by
Q355, multiplied by the pitch. Input range 0 to 99999
speed of the tool in mm/min when plunging into the Z Q253
workpiece, or when retracting from the workpiece. Q335
PREDEF. Q200 Q204
U Climb or up-cut Q351: Type of milling operation with Q201

M3
+1 = climb milling
Q203
Q239
X
Q355 = 0 Q355 = 1 Q355 > 1

Example: NC blocks

0 to 99999.9999, alternatively PREDEF 25 CYCL DEF 267 OUTSIDE THREAD MLLNG
U Depth at front Q358 (incremental): Distance Q335=10 ;NOMINAL DIAMETER

between tool tip and the top surface of the workpiece Q239=+1.5 ;PITCH
for countersinking at the front of the tool. Input range
-99999.9999 to 99999.9999 Q201=-20 ;DEPTH OF THREAD
U Countersinking offset at front Q359 (incremental): Q355=0 ;THREADS PER STEP

Distance by which the TNC moves the tool center Q253=750 ;F PRE-POSITIONING
away from the stud center. Input range 0 to
99999.9999 Q351=+1 ;CLIMB OR UP-CUT
Coordinate of the workpiece surface. Input range: Q358=+0 ;DEPTH AT FRONT
-99999.9999 to 99999.9999
U 2nd setup clearance Q204 (incremental): Coordinate Q203=+30 ;SURFACE COORDINATE
and workpiece (fixtures) can occur. Input range 0 to Q204=50 ;2ND SETUP CLEARANCE
99999.9999, alternatively PREDEF Q254=150 ;F COUNTERSINKING
U Feed rate for countersinking Q254: Traversing Q207=500 ;FEED RATE FOR MILLING
speed of the tool during countersinking in mm/min.
99999.999, alternatively FAUTO.

Example: Thread milling
The drill hole coordinates are stored in the point

table TAB1.PNT and are called by the TNC with
CYCL CALL PAT.
Y
M6
The tool radii are selected so that all work steps
100
can be seen in the test graphics.
90
Program sequence
65
Centering
Drilling 55
Tapping
30
10
X
10 20 40 80 90 100
0 BEGIN PGM 1 MM
2 BLK FORM 0.2 X+100 Y+100 Y+0
3 TOOL DEF 1 L+0 R+4 Tool definition of center drill
4 TOOL DEF 2 L+0 2.4 Tool definition of drill
5 TOOL DEF 3 L+0 R+3 Tool definition of tap
6 TOOL CALL 1 Z S5000 Tool call of centering drill
7 L Z+10 R0 F5000 Move tool to clearance height (enter a value for F).
The TNC positions to the clearance height after every cycle
8 SEL PATTERN “TAB1” Defining point tables
9 CYCL DEF 200 DRILLING Cycle definition: CENTERING
Q201=-2 ;DEPTH
Q203=+0 ;SURFACE COORDINATE 0 must be entered here, effective as defined in point table

Q204=0 ;2ND SETUP CLEARANCE 0 must be entered here, effective as defined in point table
10 CYCL CALL PAT F5000 M3 Cycle call in connection with point table TAB1.PNT
Feed rate between points: 5000 mm/min
11 L Z+100 R0 FMAX M6 Retract the tool, change the tool
12 TOOL CALL 2 Z S5000 Call tool: drill
Q201=-25 ;DEPTH
16 L Z+100 R0 FMAX M6 Retract the tool, change the tool
17 TOOL CALL 3 Z S200 Tool call for tap
18 L Z+50 R0 FMAX Move tool to clearance height
19 CYCL DEF 206 TAPPING NEW Cycle definition for tapping
22 END PGM 1 MM

Point table TAB1.PNT
TAB1. PNT MM
NR X Y Z
0 +10 +10 +0
1 +40 +30 +0
2 +90 +10 +0
3 +80 +30 +0
4 +80 +65 +0
5 +90 +90 +0
6 +10 +90 +0
7 +20 +55 +0
[END]

Fixed Cycles: Pocket
Milling / Stud Milling /
Slot Milling
5.1 Basics
5.1 Basics
Overview
The TNC offers 6 cycles for machining pockets, studs and slots:
Cycle Soft key Page

251 RECTANGULAR POCKET Page 141
Roughing/finishing cycle with selection
of machining operation and helical
plunging
252 CIRCULAR POCKET Page 146

of machining operation and helical
plunging
253 SLOT MILLING Page 150

of machining operation and reciprocal
plunging
254 CIRCULAR SLOT Page 155

of machining operation and reciprocal
plunging
256 RECTANGULAR STUD Page 160

Roughing/finishing cycle with stepover, if
multiple passes are required
257 CIRCULAR STUD Page 164

Roughing/finishing cycle with stepover, if
multiple passes are required
140 Fixed Cycles: Pocket Milling / Stud Milling / Slot Milling

5.2 RECTANGULAR POCKET (Cycle 251, DIN/ISO: G251)
5.2 RECTANGULAR POCKET
Cycle run
Use Cycle 251 RECTANGULAR POCKET to completely machine
rectangular pockets. Depending on the cycle parameters, the
following machining alternatives are available:
Complete machining: Roughing, floor finishing, side finishing
Only roughing
Only floor finishing and side finishing
Only floor finishing
Only side finishing
Roughing
1 The tool plunges into the workpiece at the pocket center and
advances to the first plunging depth. Specify the plunging strategy
with Parameter Q366.
2 The TNC roughs out the pocket from the inside out, taking the
overlap factor (Parameter Q370) and the finishing allowances
(parameters Q368 and Q369) into account.
3 At the end of the roughing operation, the TNC moves the tool
tangentially away from the pocket wall, then moves by the setup
clearance above the current pecking depth and returns from there
at rapid traverse to the pocket center.
4 This process is repeated until the programmed pocket depth is
reached.
Finishing
5 Inasmuch as finishing allowances are defined, the TNC then
finishes the pocket walls, in multiple infeeds if so specified. The
pocket wall is approached tangentially.
6 Then the TNC finishes the floor of the pocket from the inside out.
The pocket floor is approached tangentially.

With an inactive tool table you must always plunge

vertically (Q366=0) because you cannot define a plunging
angle.
Pre-position the tool in the machining plane to the starting
position with radius compensation R0. Note Parameter
Q367 (pocket position).
The TNC runs the cycle in the axes (machining plane) with
which you approached the starting position. For example,
in X and Y if you programmed CYCL CALL POS X... Y... or
in U and V if you programmed CYCL CALL POS U... V...
The TNC automatically pre-positions the tool in the tool
axis. Note Parameter Q204 (2nd setup clearance).
At the end of the cycle, the TNC returns the tool to the
starting position.
At the end of a roughing operation, the TNC positions the
tool back to the pocket center at rapid traverse. The tool is
above the current pecking depth by the setup clearance.
Enter the setup clearance so that the tool cannot jam
because of chips.
is entered.
If you call the cycle with machining operation 2 (only
finishing), then the TNC positions the tool in the center of
the pocket at rapid traverse to the first plunging depth.

Cycle parameters
U Machining operation (0/1/2) Q215: Define the
machining operation: Y Q218
0: Roughing and finishing
1: Only roughing
2: Only finishing
Side finishing and floor finishing are only executed if
the finishing allowances (Q368, Q369) have been
Q
22
defined.
Q219
U First side length Q218 (incremental): Pocket length, Q207
parallel to the reference axis of the working plane.
U 2nd side length Q219 (incremental): Pocket length,
parallel to the minor axis of the working plane. Input
range 0 to 99999.9999 X
U Corner radius Q220: Radius of the pocket corner. If
you have entered 0 here, the TNC assumes that the
corner radius is equal to the tool radius. Input range 0
to 99999.9999 Y Y
U Finishing allowance for side Q368 (incremental):

Finishing allowance in the working plane. Input range
Q367=0
0 to 99999.9999
U Angle of rotation Q224 (absolute): Angle by which Q367=1 Q367=2
the entire pocket is rotated. The center of rotation is X X
the position at which the tool is located when the
cycle is called. Input range -360.0000 to 360.0000 Y Y
Q367=3 Q367=4
U Pocket position Q367: Position of the pocket in
reference to the position of the tool when the cycle is
called:
0: Tool position = Center of pocket
1: Tool position = Lower left corner
X X
2: Tool position = Lower right corner
3: Tool position = Upper right corner
4: Tool position = Upper left corner
U Feed rate for milling Q207: Traversing speed of the Y
99999.999; alternatively FAUTO, FU, FZ
M3:
+1 = climb milling Q351= 1
Q351= +1
k X

workpiece surface and bottom of pocket. Input range:
-99999.9999 to 99999.9999
Q206
Enter a value greater than 0. Input range 0 to Z
99999.9999
U Finishing allowance for floor Q369 (incremental):
Q338
Finishing allowance in the tool axis. Input range 0 to
99999.9999 Q202
Q201
the tool while moving to depth in mm/min. Input
range: 0 to 99999.999; alternatively FAUTO, FU, FZ.
U Infeed for finishing Q338 (incremental): Infeed per
cut. Q338=0: Finishing in one infeed. Input range 0 to X
99999.9999
0 to 99999.9999, alternatively PREDEF Z
Absolute coordinate of the workpiece surface. Input
range -99999.9999 to 99999.9999
in the spindle axis at which no collision between tool Q200 Q204
and workpiece (fixtures) can occur. Input range 0 to Q368
Q369
Q203

Example: NC blocks

U Path overlap factor Q370: Q370 x tool radius =
stepover factor k. Input range: 0.1 to 1.414
alternatively PREDEF. 8 CYCL DEF 251 RECTANGULAR POCKET
U Plunging strategy Q366: Type of plunging strategy: Q215=0 ;MACHINING OPERATION
0 = vertical plunging. The TNC plunges Q218=80 ;FIRST SIDE LENGTH

perpendicularly, regardless of the plunging angle Q219=60 ;2ND SIDE LENGTH
ANGLE defined in the tool table.
Q220=5 ;CORNER RADIUS
1 = helical plunging. In the tool table, the plunging
angle ANGLE for the active tool must be defined as Q368=0.2 ;ALLOWANCE FOR SIDE
not equal to 0. The TNC will otherwise display an Q224=+0 ;ANGLE OF ROTATION
error message.
Q367=0 ;POCKET POSITION
2 = reciprocating plunge. In the tool table, the
plunging angle ANGLE for the active tool must be Q207=500 ;FEED RATE FOR MILLING
defined as not equal to 0. Otherwise, the TNC
generates an error message. The reciprocation
length depends on the plunging angle. As a Q201=-20 ;DEPTH
minimum value the TNC uses twice the tool
diameter.
Alternative: PREDEF Q369=0.1 ;ALLOWANCE FOR FLOOR
U Feed rate for finishing Q385: Traversing speed of Q206=150 ;FEED RATE FOR PLUNGING
the tool during side and floor finishing in mm/min. Q338=5 ;INFEED FOR FINISHING
Input range: 0 to 99999.9999; alternatively FAUTO, FU,
FZ. Q200=2 ;SETUP CLEARANCE
Q370=1 ;TOOL PATH OVERLAP
Q366=1 ;PLUNGE
Q385=500 ;FEED RATE FOR FINISHING

5.3 CIRCULAR POCKET (Cycle 252, DIN/ISO: G252)
5.3 CIRCULAR POCKET (Cycle 252,
DIN/ISO: G252)
Cycle run
Use Cycle 252 CIRCULAR POCKET to completely machine circular
pockets. Depending on the cycle parameters, the following machining
alternatives are available:
Only roughing
Only side finishing
Roughing
1 The tool plunges into the workpiece at the pocket center and
advances to the first plunging depth. Specify the plunging strategy
with Parameter Q366.
2 The TNC roughs out the pocket from the inside out, taking the
overlap factor (Parameter Q370) and the finishing allowances
(parameters Q368 and Q369) into account.
3 At the end of the roughing operation, the TNC moves the tool
tangentially away from the pocket wall, then moves by the setup
clearance above the current pecking depth and returns from there
at rapid traverse to the pocket center.
4 This process is repeated until the programmed pocket depth is
reached.
Finishing
finishes the pocket walls, in multiple infeeds if so specified. The
pocket wall is approached tangentially.
6 Then the TNC finishes the floor of the pocket from the inside out.
The pocket floor is approached tangentially.


angle.
Pre-position the tool in the machining plane to the
starting position (circle center) with radius
compensation R0.
starting position.
At the end of a roughing operation, the TNC positions the
tool back to the pocket center at rapid traverse. The tool is
above the current pecking depth by the setup clearance.
Enter the setup clearance so that the tool cannot jam
because of chips.
is entered.
finishing), then the TNC positions the tool in the center of
the pocket at rapid traverse to the first plunging depth.

Cycle parameters
machining operation: Y
1: Only roughing
2: Only finishing
the finishing allowances (Q368, Q369) have been Q207
defined.
Q223
U Circle diameter Q223: Diameter of the finished
pocket. Input range 0 to 99999.9999
0 to 99999.9999
X
M3:
+1 = climb milling
Alternatively PREDEF Q206
Z
workpiece surface and bottom of pocket. Input range:
-99999.9999 to 99999.9999 Q338
U Plunging depth Q202 (incremental): Infeed per cut. Q202

Enter a value greater than 0. Input range 0 to
99999.9999 Q201

99999.9999 X
cut. Q338=0: Finishing in one infeed. Input range 0 to
99999.9999

range -99999.9999 to 99999.9999
Q369
U Path overlap factor Q370: Q370 x tool radius = Q203
alternatively PREDEF.
U Plunging strategy Q366: Type of plunging strategy: X
0 = vertical plunging. The TNC plunges
perpendicularly, regardless of the plunging angle Example: NC blocks
ANGLE defined in the tool table.
8 CYCL DEF 252 CIRCULAR POCKET
angle ANGLE for the active tool must be defined as Q215=0 ;MACHINING OPERATION
not equal to 0. The TNC will otherwise display an
Q223=60 ;CIRCLE DIAMETER
error message.
Alternative: PREDEF Q368=0.2 ;ALLOWANCE FOR SIDE
U Feed rate for finishing Q385: Traversing speed of Q207=500 ;FEED RATE FOR MILLING
the tool during side and floor finishing in mm/min. Q351=+1 ;CLIMB OR UP-CUT
FZ. Q201=-20 ;DEPTH
Q369=0.1 ;ALLOWANCE FOR FLOOR
Q206=150 ;FEED RATE FOR PLUNGING
Q338=5 ;INFEED FOR FINISHING
Q366=1 ;PLUNGE

5.4 SLOT MILLING (Cycle 253, DIN/ISO: G253)
5.4 SLOT MILLING (Cycle 253,
DIN/ISO: G253)
Cycle run
Use Cycle 253 to completely machine a slot. Depending on the cycle
parameters, the following machining alternatives are available:
Only roughing
Only side finishing
Roughing
1 Starting from the left slot arc center, the tool moves in a
reciprocating motion at the plunging angle defined in the tool table
to the first infeed depth. Specify the plunging strategy with
Parameter Q366.
2 The TNC roughs out the slot from the inside out, taking the
finishing allowances (parameters Q368 and Q369) into account.
3 This process is repeated until the slot depth is reached.
Finishing
finishes the slot walls, in multiple infeeds if so specified. The slot
side is approached tangentially in the right slot arc.
5 Then the TNC finishes the floor of the slot from the inside out. The
slot floor is approached tangentially.


angle.
Q367 (slot position).
At the end of the cycle the TNC merely moves the tool in
working plane back to the center of the slot; in the other
working plane axis the TNC does not do any positioning. If
you define a slot position not equal to 0, then the TNC only
positions the tool in the tool axis to the 2nd setup
clearance. Prior to a new cycle call, move the tool back to
the starting position or program always absolute traverse
motions after the cycle call.
If the slot width is greater than twice the tool diameter, the
TNC roughs the slot correspondingly from inside out. You
can therefore mill any slots with small tools, too.
is entered.
finishing), then the TNC positions the tool to the first
plunging depth at rapid traverse!

Cycle parameters
1: Only roughing
2: Only finishing
Q218
the finishing allowances (Q368, Q369) have been
defined. Q374
U Slot length Q218 (value parallel to the reference axis
Q219
of the working plane): Enter the length of the slot.
U Slot width Q219 (value parallel to the secondary axis
of the working plane): Enter the slot width. If you
enter a slot width that equals the tool diameter, the X
TNC will carry out the roughing process only (slot
milling). Maximum slot width for roughing: Twice the
tool diameter. Input range 0 to 99999.9999
U Finishing allowance for side Q368 (incremental): Y Y
Finishing allowance in the working plane. Q367=1 Q367=2
U Angle of rotation Q374 (absolute): Angle by which
the entire slot is rotated. The center of rotation is the
position at which the tool is located when the cycle is Q367=0
called. Input range -360.000 to 360.000
X X
U Slot position (0/1/2/3/4) Q367: Position of the slot
in reference to the position of the tool when the cycle Y Y
is called: Q367=3 Q367=4
0: Tool position = Center of slot
1: Tool position = Left end of slot
2: Tool position = Center of left slot circle
3: Tool position = Center of right slot circle
4: Tool position = Right end of slot X X
M3:
+1 = climb milling

workpiece surface and bottom of slot. Input range
-99999.9999 to 99999.9999
Q206
99999.9999
Q338
99999.9999 Q202
Q201
cut. Q338=0: Finishing in one infeed. Input range 0 to X
99999.9999

range -99999.9999 to 99999.9999
Q369
U Plunging strategy Q366: Type of plunging strategy: Q203

perpendicularly, regardless of the plunging angle
ANGLE defined in the tool table. X
angle ANGLE for the active tool must be defined as Example: NC blocks
not equal to 0. Otherwise, the TNC generates an
error message. Plunge on a helical path only if there 8 CYCL DEF 253 SLOT MILLING
is enough space.
Q215=0 ;MACHINING OPERATION
plunging angle ANGLE for the active tool must be Q218=80 ;SLOT LENGTH
defined as not equal to 0. The TNC will otherwise Q219=12 ;SLOT WIDTH
display an error message.
Q368=0.2 ;ALLOWANCE FOR SIDE
Alternative: PREDEF
Q374=+0 ;ANGLE OF ROTATION
U Feed rate for finishing Q385: Traversing speed of
the tool during side and floor finishing in mm/min. Q367=0 ;SLOT POSITION
Input range: 0 to 99999.9999; alternatively FAUTO, FU, Q207=500 ;FEED RATE FOR MILLING
FZ.
Q201=-20 ;DEPTH
Q366=1 ;PLUNGE

5.5 CIRCULAR SLOT (Cycle 254, DIN/ISO: G254)
5.5 CIRCULAR SLOT (Cycle 254,
DIN/ISO: G254)
Cycle run
Use Cycle 254 to completely machine a circular slot. Depending on the
cycle parameters, the following machining alternatives are available:
Only roughing
Only side finishing
Roughing
1 The tool moves in a reciprocating motion in the slot center at the
plunging angle defined in the tool table to the first infeed depth.
Specify the plunging strategy with Parameter Q366.
2 The TNC roughs out the slot from the inside out, taking the
finishing allowances (parameters Q368 and Q369) into account.
3 This process is repeated until the slot depth is reached.
Finishing
finishes the slot walls, in multiple infeeds if so specified. The slot
side is approached tangentially.
5 Then the TNC finishes the floor of the slot from the inside out. The
slot floor is approached tangentially.


angle.
Pre-position the tool in the machining plane with radius
compensation R0. Define Parameter Q367 (Reference for
slot position) appropriately.
At the end of the cycle the TNC merely moves the tool in
working plane back to the center of the pitch circle; in the
other working plane axis the TNC does not do any
positioning. If you define a slot position not equal to 0,
then the TNC only positions the tool in the tool axis to the
2nd setup clearance. Prior to a new cycle call, move the
tool back to the starting position or program always
absolute traverse motions after the cycle call.
At the end of the cycle the TNC returns the tool to the
starting point (center of the pitch circle) in the working
plane. Exception: if you define a slot position not equal to
0, then the TNC only positions the tool in the tool axis to
the 2nd setup clearance. In these cases, always program
absolute traverse movements after the cycle call.
If the slot width is greater than twice the tool diameter, the
TNC roughs the slot correspondingly from inside out. You
can therefore mill any slots with small tools, too.
The slot position 0 is not allowed if you use Cycle 254
Circular Slot in combination with Cycle 221.
is entered.
finishing), then the TNC positions the tool to the first
plunging depth at rapid traverse!

Cycle parameters
1: Only roughing
2: Only finishing
Side finishing and floor finishing are only executed if Q248
Q219
the finishing allowances (Q368, Q369) have been Q37
5 Q376
defined.
U Slot width Q219 (value parallel to the secondary axis
of the working plane): Enter the slot width. If you
enter a slot width that equals the tool diameter, the
TNC will carry out the roughing process only (slot
milling). Maximum slot width for roughing: Twice the
tool diameter. Input range 0 to 99999.9999
U Finishing allowance for side Q368 (incremental): X
0 to 99999.9999
U Pitch circle diameter Q375: Enter the diameter of Y Y
the pitch circle. Input range 0 to 99999.9999 Q367=0 Q367=1
U Reference for slot position (0/1/2/3) Q367:
Position of the slot in reference to the position of the
tool when the cycle is called:
0: The tool position is not taken into account. The slot
X X
position is determined from the entered pitch circle
center and the starting angle. Y Y
1: Tool position = Center of left slot circle. Starting
angle Q376 refers to this position. The entered pitch Q367=2 Q367=3
circle center is not taken into account.
2: Tool position = Center of center line. Starting angle
Q376 refers to this position. The entered pitch circle
center is not taken into account.
3: Tool position = Center of right slot circle. Starting X X
angle Q376 refers to this position. The entered pitch
circle center is not taken into account.
U Center in 1st axis Q216 (absolute): Center of the
pitch circle in the reference axis of the working plane.
Only effective if Q367 = 0. Input range: -99999.9999
to 99999.9999
U Center in 2nd axis Q217 (absolute): Center of the
pitch circle in the minor axis of the working plane.
Only effective if Q367 = 0. Input range: -99999.9999
to 99999.9999
U Starting angle Q376 (absolute): Enter the polar angle
of the starting point. Input range -360.000 to 360.000
U Angular length Q248 (incremental): Enter the angular
length of the slot. Input range 0 to 360.000

U Stepping angle Q378 (incremental): Angle by which
the entire slot is rotated. The center of rotation is at Y
the center of the pitch circle. Input range -360.000 to
360.000
U Number of repetitions Q377: Number of machining 8
operations on a pitch circle. Input range 1 to 99999 Q37
Q376
M3:
+1 = climb milling
Alternatively PREDEF X
workpiece surface and bottom of slot. Input range
-99999.9999 to 99999.9999
99999.9999 Q206
Z
99999.9999 Q338
range: 0 to 99999.999; alternatively FAUTO, FU, FZ. Q201
99999.9999
X

range -99999.9999 to 99999.9999
Q369

angle ANGLE for the active tool must be defined as Example: NC blocks
not equal to 0. Otherwise, the TNC generates an
error message. Plunge on a helical path only if there 8 CYCL DEF 254 CIRCULAR SLOT
is enough space.
plunging angle ANGLE for the active tool must be Q219=12 ;SLOT WIDTH
defined as not equal to 0. Otherwise, the TNC Q368=0.2 ;ALLOWANCE FOR SIDE
generates an error message. The TNC can only
plunge reciprocally once the traversing length on Q375=80 ;PITCH CIRCLE DIA.
the circular arc is at least three times the tool Q367=0 ;REF. SLOT POSITION
diameter.
Q216=+50 ;CENTER IN 1ST AXIS
Alternative: PREDEF
Q217=+50 ;CENTER IN 2ND AXIS
the tool during side and floor finishing in mm/min. Q376=+45 ;STARTING ANGLE
Input range: 0 to 99999.999; alternatively FAUTO, FU, Q248=90 ;ANGULAR LENGTH
FZ.
Q378=0 ;STEPPING ANGLE
Q377=1 ;NUMBER OF OPERATIONS
Q201=-20 ;DEPTH
Q366=1 ;PLUNGE

5.6 RECTANGULAR STUD (Cycle 256, DIN/ISO: G256)
5.6 RECTANGULAR STUD
Cycle run
Use Cycle 256 to machine a rectangular stud. If a dimension of the
workpiece blank is greater than the maximum possible stepover, then 2mm
Y
the TNC performs multiple stepovers until the finished dimension has
been machined.
1 The tool moves from the cycle starting position (stud center) in the
positive X direction to the starting position for the stud machining.
The starting position is 2 mm to the right of the unmachined stud.
2 If the tool is at the 2nd setup clearance, it moves at rapid traverse
FMAX to the setup clearance, and from there it advances to the first
plunging depth at the feed rate for plunging.
3 The tool then moves tangentially to the stud contour and machines
one revolution.
4 If the finished dimension cannot be machined with one revolution,
the TNC performs a stepover with the current factor, and X
machines another revolution. The TNC takes the dimensions of the
workpiece blank, the finished dimension, and the permitted
stepover into account. This process is repeated until the defined
finished dimension has been reached.
5 If further stepovers are required the tool then departs the contour
on a tangential path and returns to the starting point of stud
machining.
6 The TNC then plunges the tool to the next plunging depth, and
machines the stud at this depth.
7 This process is repeated until the programmed stud depth is
reached.
8 At the end of the cycle, the TNC merely positions the tool in the
tool axis at the clearance height defined in the cycle. This means
that the end position differs from the starting position.


Q367 (stud position).
At the end, the TNC positions the tool back to the setup
clearance, or to the 2nd setup clearance if one was
programmed.
is entered.
Leave enough room next to the stud for the approach
motion. Minimum: tool diameter + 2 mm

Cycle parameters
U First side length Q218: Stud length, parallel to the
Q424
reference axis of the working plane. Input range 0 to Y Q218
99999.9999
U Workpiece blank side length 1 Q424: Length of the
stud blank, parallel to the reference axis of the
working plane. Enter Workpiece blank side length 1
Q207
Q
greater than First side length. The TNC performs
22
0
Q425
Q219
multiple stepovers if the difference between blank
dimension 1 and finished dimension 1 is greater than
the permitted stepover (tool radius multiplied by path
overlap Q370). The TNC always calculates a constant
stepover. Input range 0 to 99999.9999
U Second side length Q219: Stud length, parallel to the
minor axis of the working plane. Enter Workpiece X
blank side length 2 greater than Second side Q368
length. The TNC performs multiple stepovers if the
difference between blank dimension 2 and finished
dimension 2 is greater than the permitted stepover Y Y
(tool radius multiplied by path overlap Q370). The TNC
always calculates a constant stepover. Input range 0
to 99999.9999
Q367=0
U Workpiece blank side length 2 Q425: Length of the
stud blank, parallel to the minor axis of the working Q367=1 Q367=2
plane. Input range 0 to 99999.9999 X X
U Corner radius Q220: Radius of the stud corner. Input Y Y
range 0 to 99999.9999
Q367=3 Q367=4
Finishing allowance in the working plane, is left over
after machining. Input range 0 to 99999.9999
U Angle of rotation Q224 (absolute): Angle by which
X X
the entire stud is rotated. The center of rotation is the
position at which the tool is located when the cycle is
called. Input range -360.000 to 360.000
U Stud position Q367: Position of the stud in reference
Y
to the position of the tool when the cycle is called:
0: Tool position = Center of stud
1: Tool position = Lower left corner Q351= +1
2: Tool position = Lower right corner
3: Tool position = Upper right corner
4: Tool position = Upper left corner
Q351= 1
k X

U Climb or up-cut Q351: Type of milling operation with Q206
M3: Z
+1 = climb milling
Alternatively PREDEF Q200 Q204
Q203
U Depth Q201 (incremental): Distance between Q202
workpiece surface and bottom of stud. Input range: Q201
-99999.9999 to 99999.9999
99999.9999
X
Example: NC blocks
range: 0 to 99999.999; alternatively FMAX, FAUTO, FU,
FZ. 8 CYCL DEF 256 RECTANGULAR STUD
U Setup clearance Q200 (incremental): Distance Q218=60 ;FIRST SIDE LENGTH
0 to 99999.9999, alternatively PREDEF Q424=74 ;WORKPC. BLANK SIDE 1
U Workpiece surface coordinate Q203 (absolute): Q219=40 ;2ND SIDE LENGTH

Absolute coordinate of the workpiece surface. Input Q425=60 ;WORKPC. BLANK SIDE 2
range -99999.9999 to 99999.9999
in the spindle axis at which no collision between tool Q368=0.2 ;ALLOWANCE FOR SIDE
and workpiece (fixtures) can occur. Input range 0 to Q224=+0 ;ANGLE OF ROTATION
Q367=0 ;STUD POSITION
alternatively PREDEF. Q351=+1 ;CLIMB OR UP-CUT
Q201=-20 ;DEPTH

5.7 CIRCULAR STUD (Cycle 257, DIN/ISO: G257)
5.7 CIRCULAR STUD (Cycle 257,
DIN/ISO: G257)
Cycle run
Use Cycle 257 to machine a circular stud. If a diameter of the
workpiece blank is greater than the maximum possible stepover, then 2mm
Y
the TNC performs multiple stepovers until the finished diameter has
been machined.
1 The tool moves from the cycle starting position (stud center) in the
positive X direction to the starting position for the stud machining.
The starting position is 2 mm to the right of the unmachined stud.
2 If the tool is at the 2nd setup clearance, it moves at rapid traverse
FMAX to the setup clearance, and from there it advances to the first
plunging depth at the feed rate for plunging.
3 The tool then moves tangentially to the stud contour and machines
one revolution.
4 If the finished diameter cannot be machined with one revolution,
the TNC performs a stepover with the current factor, and X
machines another revolution. The TNC takes the dimensions of the
workpiece blank diameter, the finished diameter, and the
permitted stepover into account. This process is repeated until the
defined finished diameter has been reached.
5 If further stepovers are required the tool then departs the contour
on a tangential path and returns to the starting point of stud
machining.
6 The TNC then plunges the tool to the next plunging depth, and
machines the stud at this depth.
7 This process is repeated until the programmed stud depth is
reached.
8 At the end of the cycle after tangential departure, the TNC merely
positions the tool in the tool axis at the clearance height defined in
the cycle. This means that the end position differs from the
starting position.


position (stud center) with radius compensation R0.
starting position.
At the end, the TNC positions the tool back to the setup
clearance, or to the 2nd setup clearance if one was
programmed.
is entered.
Leave enough room next to the stud for the approach
motion. Minimum: tool diameter + 2 mm

Cycle parameters
U Finished part diameter Q223: Diameter of the
completely machined stud. Input range 0 to Y
99999.9999
U Workpiece blank diameter Q222: Diameter of the
workpiece blank. Enter the workpiece blank diameter
greater than the finished diameter. The TNC performs
Q207
multiple stepovers if the difference between the
workpiece blank diameter and finished diameter is
Q223
Q222
greater than the permitted stepover (tool radius
multiplied by path overlap Q370). The TNC always
calculates a constant stepover. Input range 0 to
99999.9999
Finishing allowance in the working plane. Input range X
0 to 99999.9999 Q368
Y
M3: Q351= 1
+1 = climb milling
Q351= +1
k X

workpiece surface and bottom of stud. Input range:
-99999.9999 to 99999.9999
99999.9999
Q200
the tool while moving to depth in mm/min. Input Q203
range: 0 to 99999.999; alternatively FMAX, FAUTO, FU, Q202
FZ. Q201
U Workpiece surface coordinate Q203 (absolute): X
range -99999.9999 to 99999.9999
Example: NC blocks
in the spindle axis at which no collision between tool 8 CYCL DEF 257 CIRCULAR STUD
and workpiece (fixtures) can occur. Input range 0 to Q223=60 ;FINISHED PART DIA.
Q222=60 ;WORKPIECE BLANK DIA.
stepover factor k. Input range: 0.1 to 1.414 Q368=0.2 ;ALLOWANCE FOR SIDE
alternatively PREDEF. Q207=500 ;FEED RATE FOR MILLING
Q201=-20 ;DEPTH

Example: Milling pockets, studs and slots
Y Y
90
100
90°
70
45°
50
80
50
X Z
50 100 -40 -30 -20
0 BEGIN PGM C210 MM

2 BLK FORM 0.2 X+100 Y+100 Z+0
3 TOOL DEF 1 L+0 R+6 Define the tool for roughing/finishing
4 TOOL DEF 2 L+0 R+3 Define slotting mill
5 TOOL CALL 1 Z S3500 Call the tool for roughing/finishing

7 CYCL DEF 256 RECTANGULAR STUD Define cycle for machining the contour outside
Q218=90 ;FIRST SIDE LENGTH
Q424=100 ;WORKPC. BLANK SIDE 1
Q219=80 ;2ND SIDE LENGTH
Q425=100 ;WORKPC. BLANK SIDE 2
Q368=0 ;ALLOWANCE FOR SIDE
Q224=0 ;ROTATIONAL POSITION
Q367=0 ;STUD POSITION
Q201=-30 ;DEPTH
8 CYCL CALL POS X+50 Y+50 Z+0 M3 Call cycle for machining the contour outside
9 CYCL DEF 252 CIRCULAR POCKET Define CIRCULAR POCKET MILLING cycle
Q223=50 ;CIRCLE DIAMETER
Q201=-30 ;DEPTH
Q366=1 ;PLUNGE
10 CYCL CALL POS X+50 Y+50 Z+0 FMAX Call CIRCULAR POCKET MILLING cycle
11 L Z+250 R0 FMAX M6 Tool change

12 TOLL CALL 2 Z S5000 Call slotting mill
13 CYCL DEF 254 CIRCULAR SLOT Define SLOT cycle
Q219=8 ;SLOT WIDTH
Q375=70 ;PITCH CIRCLE DIA.
Q367=0 ;REF. SLOT POSITION No pre-positioning in X/Y required
Q376=+45 ;STARTING ANGLE
Q248=90 ;ANGULAR LENGTH
Q378=180 ;STEPPING ANGLE Starting point for 2nd slot
Q201=-20 ;DEPTH
Q366=1 ;PLUNGE
14 CYCL CALL FMAX M3 Call SLOT cycle
16 END PGM C210 MM

Fixed Cycles: Pattern
Definitions
6.1 Fundamentals
6.1 Fundamentals
Overview
The TNC provides two cycles for machining point patterns directly:
Cycle Soft key Page

220 CIRCULAR PATTERN Page 173
221 LINEAR PATTERN Page 176
You can combine Cycle 220 and Cycle 221 with the following fixed
cycles:
If you have to machine irregular point patterns, use CYCL

CALL PAT (see “Point Tables” on page 66) to develop point
tables.
More regular point patterns are available with the PATTERN
DEF function (see “Pattern Definition PATTERN DEF” on
page 58).
Cycle 200 DRILLING

Cycle 201 REAMING
Cycle 202 BORING
Cycle 203 UNIVERSAL DRILLING
Cycle 204 BACK BORING
Cycle 205 UNIVERSAL PECKING
Cycle 206 TAPPING NEW with a floating tap holder
Cycle 207 RIGID TAPPING without a floating tap holder NEW
Cycle 208 BORE MILLING
Cycle 209 TAPPING WITH CHIP BREAKING
Cycle 240 CENTERING
Cycle 251 RECTANGULAR POCKET
Cycle 252 CIRCULAR POCKET MILLING
Cycle 253 SLOT MILLING
Cycle 254 CIRCULAR SLOT (can only be combined with Cycle
221)
Cycle 256 RECTANGULAR STUD
Cycle 257 CIRCULAR STUD
Cycle 262 THREAD MILLING
Cycle 263 THREAD MILLING/COUNTERSINKING
Cycle 264 THREAD DRILLING/MILLING
Cycle 265 HELICAL THREAD DRILLING/MILLING
Cycle 267 OUTSIDE THREAD MILLING
172 Fixed Cycles: Pattern Definitions

6.2 CIRCULAR PATTERN (Cycle 220, DIN/ISO: G220)
6.2 CIRCULAR PATTERN (Cycle 220,
DIN/ISO: G220)
Cycle run
1 The TNC moves the tool at rapid traverse from its current position
to the starting point for the first machining operation.
Sequence:
Move to the 2nd set-up clearance (spindle axis)
Approach the starting point in the spindle axis.
Move to the setup clearance above the workpiece surface
(spindle axis).
2 From this position the TNC executes the last defined fixed cycle.
3 The tool then approaches on a straight line or circular arc the
starting point for the next machining operation. The tool stops at
the set-up clearance (or the 2nd setup clearance).
4 This process (1 to 3) is repeated until all machining operations have
been executed.
Cycle 220 is DEF active, which means that Cycle 220

automatically calls the last defined fixed cycle.
If you combine Cycle 220 with one of the fixed cycles 200
to 209 and 251 to 267, the setup clearance, workpiece
surface and 2nd setup clearance that you defined in Cycle
220 will be effective for the selected fixed cycle.

Cycle parameters
pitch circle in the reference axis of the working plane. Y
Input range -99999.9999 to 99999.9999 N = Q241
pitch circle in the minor axis of the working plane. Q247
Input range -99999.9999 to 99999.9999 Q246
Q24
4 Q245
U Pitch circle diameter Q244: Diameter of the pitch
Q217
circle. Input range 0 to 99999.9999
U Starting angle Q245 (absolute): Angle between the
reference axis of the working plane and the starting
point for the first machining operation on the pitch
circle. Input range -360.000 to 360.000
U Stopping angle Q246 (absolute): Angle between the X
reference axis of the working plane and the starting Q216
point for the last machining operation on the pitch
circle (does not apply to full circles). Do not enter the
same value for the stopping angle and starting angle.
If you enter the stopping angle greater than the
starting angle, machining will be carried out
counterclockwise; otherwise, machining will be
clockwise. Input range -360.000 to 360.000
U Stepping angle Q247 (incremental): Angle between
two machining operations on a pitch circle. If you
enter an angle step of 0, the TNC will calculate the
angle step from the starting and stopping angles
and the number of pattern repetitions. If you enter
a value other than 0, the TNC will not take the
stopping angle into account. The sign for the angle
step determines the working direction (– =
clockwise). Input range -360.000 to 360.000
U Number of repetitions Q241: Number of machining
operations on a pitch circle. Input range 1 to 99999

U Workpiece surface coordinate Q203 (absolute): Z
-99999.9999 to 99999.9999
U 2nd setup clearance Q204 (incremental): Coordinate Q200 Q204
Q203
U Moving to clearance height Q301: Definition of how
the tool is to move between machining processes.
0: Move to the setup clearance between operations.
1: Move to the 2nd setup clearance between
machining operations. X
Example: NC blocks
U Type of traverse? Line=0/Arc=1 Q365: Definition of
the path function with which the tool is to move 53 CYCLE DEF 220 POLAR PATTERN
between machining operations.
0: Move between operations on a straight line Q216=+50 ;CENTER IN 1ST AXIS
1: Move between operations on the pitch circle Q217=+50 ;CENTER 2ND AXIS
Q246=+360 ;STOPPING ANGLE
Q247=+0 ;STEPPING ANGLE
Q301=1 ;MOVE TO CLEARANCE
Q365=0 ;TYPE OF TRAVERSE

6.3 LINEAR PATTERN (Cycle 221, DIN/ISO: G221)
6.3 LINEAR PATTERN (Cycle 221,
DIN/ISO: G221)
Cycle run
1 The TNC automatically moves the tool from its current position to
the starting point for the first machining operation.
Sequence:
Z
Move to the 2nd set-up clearance (spindle axis)
Approach the starting point in the spindle axis. Y
Move to the setup clearance above the workpiece surface
(spindle axis). X
2 From this position the TNC executes the last defined fixed cycle.
3 The tool then approaches the starting point for the next machining
operation in the positive reference axis direction at the setup
clearance (or the 2nd setup clearance).
4 This process (1 to 3) is repeated until all machining operations on
the first line have been executed. The tool is located above the last
point on the first line.
5 The tool subsequently moves to the last point on the second line
where it carries out the machining operation.
6 From this position the tool approaches the starting point for the
next machining operation in the negative reference axis direction.
7 This process (6) is repeated until all machining operations in the
second line have been executed.
8 The tool then moves to the starting point of the next line.
9 All subsequent lines are processed in a reciprocating movement.
Cycle 221 is DEF active, which means that Cycle 221

automatically calls the last defined fixed cycle.
If you combine Cycle 221 with one of the fixed cycles 200
to 209 and 251 to 267, the setup clearance, workpiece
surface, 2nd setup clearance and the rotational position
that you defined in Cycle221 will be effective for the
selected fixed cycle.
The slot position 0 is not allowed if you use Cycle 254
Circular Slot in combination with Cycle 221.

6.3 LINEAR PATTERN (Cycle 221, DIN/ISO: G221)
Cycle parameters
U Starting point 1st axis Q225 (absolute): Coordinate
of the starting point in the reference axis of the Y
working plane.
7
U Starting point 2nd axis Q226 (absolute): Coordinate Q23
of the starting point in the minor axis of the working Q238
plane.
3
U Spacing in 1st axis Q237 (incremental): Spacing Q24
N=
between each point on a line.
2
Q24
U Spacing in 2nd axis Q238 (incremental): Spacing N=
between each line. Q224
Q226
U Number of columns Q242: Number of machining
operations on a line.
U Number of lines Q243: Number of passes. X
Q225
U Rotational position Q224 (absolute): Angle by
which the entire pattern is rotated. The center of
rotation lies in the starting point.
between tool tip and workpiece surface, alternatively
PREDEF. Z
Coordinate of the workpiece surface. Q200 Q204
Q203
and workpiece (fixtures) can occur, alternatively
PREDEF.
U Moving to clearance height Q301: Definition of how
the tool is to move between machining processes.
0: Move to the setup clearance between operations. X
1: Move to the 2nd setup clearance between
machining operations.
Alternatively PREDEF Example: NC blocks
54 CYCL DEF 221 CARTESIAN PATTERN

Q225=+15 ;STARTING PNT 1ST AXIS
Q226=+15 ;STARTING PNT 2ND AXIS
Q237=+10 ;SPACING IN 1ST AXIS
Q238=+8 ;SPACING IN 2ND AXIS
Q242=6 ;NUMBER OF COLUMNS
Q243=4 ;NUMBER OF LINES
Q224=+15 ;ROTATIONAL POSITION

Example: Circular hole patterns
100
R25
70 30°
R35
25
X
30 90 100
0 BEGIN PGM PATTERN MM

2 BLK FORM 0.2 Y+100 Y+100 Z+0
3 TOOL DEF 1 L+0 R+3 Tool definition
4 TOOL CALL 1 Z S3500 Tool call
5 L Z+250 R0 FMAX M3 Retract the tool
Q201=-15 ;DEPTH
Q210=0 ;DWELL TIME

7 CYCLE DEF 220 POLAR PATTERN Define cycle for circular pattern 1, CYCL 200 is called automatically.
Q216=+30 ;CENTER IN 1ST AXIS Q200, Q203 and Q204 are effective as defined in Cycle 220.
Q241=10 ;QUANTITY
8 CYCLE DEF 220 POLAR PATTERN Define cycle for circular pattern 2, CYCL 200 is called automatically.
Q216=+90 ;CENTER IN 1ST AXIS Q200, Q203 and Q204 are effective as defined in Cycle 220.
Q247=30 ;STEPPING ANGLE
Q241=5 ;QUANTITY
Q200=2 ;SET-UP CLEARANCE
10 END PGM PATTERN MM


Fixed Cycles: Contour
Pocket, Contour Trains
7.1 SL Cycles
7.1 SL Cycles
Fundamentals
SL cycles enable you to form complex contours by combining up to 12 Example: Program structure: Machining with SL
subcontours (pockets or islands). You define the individual cycles
subcontours in subprograms. The TNC calculates the total contour
from the subcontours (subprogram numbers) that you enter in Cycle 0 BEGIN PGM SL2 MM
14 CONTOUR GEOMETRY. ...
The memory capacity for programming an SL cycle (all 12 CYCL DEF 14 CONTOUR GEOMETRY ...
contour subprograms) is limited. The number of possible 13 CYCL DEF 20 CONTOUR DATA ...
contour elements depends on the type of contour (inside or
outside contour) and the number of subcontours. You can ...
program up to 8192 contour elements. 16 CYCL DEF 21 PILOT DRILLING ...
SL cycles conduct comprehensive and complex internal 17 CYCL CALL
calculations as well as the resulting machining operations.
For safety reasons, always run a graphical program test ...
before machining! This is a simple way of finding out 18 CYCL DEF 22 ROUGH OUT ...
whether the TNC-calculated program will provide the
desired results. 19 CYCL CALL
...
Characteristics of the subprograms 22 CYCLE DEF 23 FLOOR FINISHING ...
Coordinate transformations are allowed. If they are programmed 23 CYCL CALL
within the subcontour they are also effective in the following ...
subprograms, but they need not be reset after the cycle call.
The TNC ignores feed rates F and miscellaneous functions M. 26 CYCL DEF 24 SIDE FINISHING ...
The TNC recognizes a pocket if the tool path lies inside the contour, 27 CYCL CALL
for example if you machine the contour clockwise with radius ...
compensation RR.
50 L Z+250 R0 FMAX M2
The TNC recognizes an island if the tool path lies outside the
contour, for example if you machine the contour clockwise with 51 LBL 1
radius compensation RL.
...
The subprograms must not contain spindle axis coordinates.
55 LBL 0
The working plane is defined in the first coordinate block of the
subprogram. The secondary axes U,V,W are permitted in useful 56 LBL 2
combinations. Always define both axes of the machining plane in ...
the first block.
If you use Q parameters, then only perform the calculations and 60 LBL 0
assignments within the affected contour subprograms. ...
99 END PGM SL2 MM
182 Fixed Cycles: Contour Pocket, Contour Trains

7.1 SL Cycles
Characteristics of the fixed cycles
The TNC automatically positions the tool to the setup clearance
before a cycle.
Each level of infeed depth is milled without interruptions since the
cutter traverses around islands instead of over them.
In order to avoid leaving dwell marks, the TNC inserts a globally
definable rounding radius at non-tangential inside corners. The
rounding radius, which is entered in Cycle 20, affects the tool center
point path, meaning that it would increase a rounding defined by the
tool radius (applies to rough-out and side finishing).
The contour is approached in a tangential arc for side finishing.
For floor finishing, the tool again approaches the workpiece on a
tangential arc (for tool axis Z, for example, the arc may be in the Z/X
plane).
The contour is machined throughout in either climb or up-cut milling.
The miscellaneous functions M109 and M110 (feed rate at circular
arcs) are not effective within SL cycles, even if you programmed
these before a cycle call.
With bit 4 in MP7420 you can determine where the tool is

positioned at the end of Cycles 21 to 24.
Bit 4 = 0:
At the end of the cycle, the TNC at first positions the tool
in the tool axis at the clearance height (Q7) defined in the
cycle, and then to the position in the working plane at
which the tool was located when the cycle was called.
Bit 4 = 1:
At the end of the cycle, the TNC always positions the tool
in the tool axis at the clearance height (Q7) defined in the
cycle. Ensure that no collisions can occur during the
following positioning movements!
The machining data (such as milling depth, finishing allowance and

setup clearance) are entered as CONTOUR DATA in Cycle 20.

7.1 SL Cycles
Overview
Cycle Soft key Page

14 CONTOUR GEOMETRY (essential) Page 185
20 CONTOUR DATA (essential) Page 190
21 PILOT DRILLING (optional) Page 192
22 ROUGH OUT (essential) Page 194
23 FLOOR FINISHING (optional) Page 198
24 SIDE FINISHING (optional) Page 199
Enhanced cycles:
Cycle Soft key Page

25 CONTOUR TRAIN Page 201
270 CONTOUR TRAIN DATA Page 203
275 TROCHOIDAL SLOT Page 205

7.2 CONTOUR GEOMETRY (Cycle 14, DIN/ISO: G37)
7.2 CONTOUR GEOMETRY
All subprograms that are superimposed to define the contour are
listed in Cycle 14 CONTOUR GEOMETRY.
Before programming, note the following: C D

Cycle 14 is DEF active which means that it becomes A B
effective as soon as it is defined in the part program.
You can list up to 12 subprograms (subcontours) in
Cycle 14.
Cycle parameters
U Label numbers for the contour: Enter all label
numbers for the individual subprograms that are to be
superimposed to define the contour. Confirm every
label number with the ENT key. When you have
entered all numbers, conclude entry with the END
key. Entry of up to 12 subprogram numbers 1 to 254.

7.3 Overlapping Contours
Basics
Pockets and islands can be overlapped to form a new contour. You can
thus enlarge the area of a pocket by another pocket or reduce it by an
island. Y
S1
A B
S2
Example: NC blocks
12 CYCL DEF 14.0 CONTOUR GEOMETRY

13 CYCL DEF 14.1 CONTOUR LABEL1/2/3/4

Subprograms: overlapping pockets
The subsequent programming examples are contour

subprograms that are called by Cycle 14 CONTOUR
GEOMETRY in a main program.
Pockets A and B overlap.

The TNC calculates the points of intersection S1 and S2. They do not
have to be programmed.
The pockets are programmed as full circles.
Subprogram 1: Pocket A
51 LBL 1
52 L X+10 Y+50 RR
53 CC X+35 Y+50
54 C X+10 Y+50 DR-
55 LBL 0
51 LBL 1
52 L X+10 Y+50 RR
53 CC X+35 Y+50
54 C X+10 Y+50 DR-
55 LBL 0
Subprogram 2: Pocket B
56 LBL 2
57 L X+90 Y+50 RR
58 CC X+65 Y+50
59 C X+90 Y+50 DR-
60 LBL 0

Area of inclusion
Both surfaces A and B are to be machined, including the overlapping
area:
The surfaces A and B must be pockets.
The first pocket (in Cycle 14) must start outside the second pocket.
Surface A: B
51 LBL 1
A
52 L X+10 Y+50 RR
53 CC X+35 Y+50
54 C X+10 Y+50 DR-
55 LBL 0
Surface B:
56 LBL 2
57 L X+90 Y+50 RR
58 CC X+65 Y+50
59 C X+90 Y+50 DR-
60 LBL 0

Area of exclusion
Surface A is to be machined without the portion overlapped by B:
Surface A must be a pocket and B an island.
A must start outside of B.
B must start inside of A.
Surface A:
B
51 LBL 1
A
52 L X+10 Y+50 RR
53 CC X+35 Y+50
54 C X+10 Y+50 DR-
55 LBL 0
Surface B:
56 LBL 2
57 L X+90 Y+50 RL
58 CC X+65 Y+50
59 C X+90 Y+50 DR-
60 LBL 0
Area of intersection
Only the area where A and B overlap is to be machined. (The areas
covered by A or B alone are to be left unmachined.)
A and B must be pockets.
A must start inside of B.
Surface A: A B
51 LBL 1
52 L X+60 Y+50 RR
53 CC X+35 Y+50
54 C X+60 Y+50 DR-
55 LBL 0
Surface B:
56 LBL 2
57 L X+90 Y+50 RR
58 CC X+65 Y+50
59 C X+90 Y+50 DR-
60 LBL 0

7.4 CONTOUR DATA (Cycle 20, DIN/ISO: G120)
7.4 CONTOUR DATA (Cycle 20,
DIN/ISO: G120)
Machining data for the subprograms describing the subcontours are
entered in Cycle 20.
Cycle 20 is DEF active, which means that it becomes

= 0, the TNC performs the cycle at the depth 0.
The machining data entered in Cycle 20 are valid for Cycles
21 to 24.
If you are using the SL cycles in Q parameter programs,
the cycle parameters Q1 to Q20 cannot be used as
program parameters.

Cycle parameters
U Milling depth Q1 (incremental): Distance between
workpiece surface and bottom of pocket. Input range
-99999.9999 to 99999.9999 Y
U Path overlap factor Q2: Q2 x tool radius = stepover
factor k. Input range -0.0001 to 1.9999.
Finishing allowance in the working plane. Input range: Q9=1
8
Q
-99999.9999 to 99999.9999
U Finishing allowance for floor Q4
Q9=+1
(incremental): Finishing allowance in the tool axis.
Input range -99999.9999 to 99999.9999
Absolute coordinate of the workpiece surface. Input k
range -99999.9999 to 99999.9999 X
U Setup clearance Q6 (incremental): Distance between

tool tip and workpiece surface. Input range 0 to
Z
U Clearance height Q7 (absolute): Absolute height at
which the tool cannot collide with the workpiece (for
intermediate positioning and retraction at the end of
the cycle). Input range -99999.9999 to 99999.9999,
U Inside corner radius Q8: Inside “corner” rounding Q6
radius; entered value is referenced to the path of the
tool center. Q8 is not a radius that is inserted as a Q10 Q7
Q1
separate contour element between programmed
elements! Input range 0 to 99999.9999 Q5
U Direction of rotation? Q9: Machining direction for

pockets. X
Q9 = –1 up-cut milling for pocket and island
Q9 = +1 climb milling for pocket and island Example: NC blocks
Alternative: PREDEF
57 CYCL DEF 20 CONTOUR DATA
You can check the machining parameters during a program
interruption and overwrite them if required. Q1=-20 ;MILLING DEPTH
Q3=+0.2 ;ALLOWANCE FOR SIDE
Q4=+0.1 ;ALLOWANCE FOR FLOOR
Q7=+80 ;CLEARANCE HEIGHT
Q8=0.5 ;ROUNDING RADIUS
Q9=+1 ;DIRECTION

7.5 PILOT DRILLING (Cycle 21, DIN/ISO: G121)
7.5 PILOT DRILLING (Cycle 21,
DIN/ISO: G121)
Cycle run
1 The tool drills from the current position to the first plunging depth
at the programmed feed rate F.
2 Then the tool retracts at rapid traverse FMAX to the starting position
and advances again to the first plunging depth minus the advanced
stop distance t.
3 The advanced stop distance is automatically calculated by the
control:
At a total hole depth up to 30 mm: t = 0.6 mm
At a total hole depth exceeding 30 mm: t = hole depth / 50
Maximum advanced stop distance: 7 mm
feed rate F.
5 The TNC repeats this process (1 to 4) until the programmed depth
is reached.
6 After a dwell time at the hole bottom, the tool is returned to the
starting position at rapid traverse FMAX for chip breaking.
Application
Cycle 21 is for PILOT DRILLING of the cutter infeed points. It accounts
for the allowance for side and the allowance for floor as well as the
radius of the rough-out tool. The cutter infeed points also serve as
starting points for roughing.

When calculating the infeed points, the TNC does not
account for the delta value DR programmed in a TOOL CALL
block.
In narrow areas, the TNC may not be able to carry out pilot
drilling with a tool that is larger than the rough-out tool.

7.5 PILOT DRILLING (Cycle 21, DIN/ISO: G121)
Cycle parameters
U Plunging depth Q10 (incremental): Dimension by
which the tool drills in each infeed (negative sign for
negative working direction). Input range: -99999.9999
to 99999.9999 Y
U Feed rate for plunging Q11: Drilling feed rate in
mm/min. Input range: 0 to 99999.9999; alternatively
FAUTO, FU, FZ.
U Rough-out tool number/name Q13 or QS13: Number
or name of rough-out tool. Input range 0 to 32767.9 if
a number is entered; maximum 16 characters if a
name is entered.
Example: NC blocks
58 CYCL DEF 21 PILOT DRILLING

Q10=+5 ;PLUNGING DEPTH
Q13=1 ;ROUGH-OUT TOOL

7.6 ROUGH-OUT (Cycle 22, DIN/ISO: G122)
7.6 ROUGH-OUT (Cycle 22,
DIN/ISO: G122)
Cycle run
1 The TNC positions the tool over the cutter infeed point, taking the
allowance for side into account.
2 In the first plunging depth, the tool mills the contour from the
inside outward at the milling feed rate Q12.
3 The island contours (here: C/D) are cleared out with an approach
toward the pocket contour (here: A/B).
4 In the next step the TNC moves the tool to the next plunging depth
and repeats the roughing procedure until the program depth is
reached.
5 Finally the TNC retracts the tool to the clearance height.

This cycle requires a center-cut end mill (ISO 1641) or pilot

drilling with Cycle 21.
You define the plunging behavior of Cycle 22 with
parameter Q19 and with the tool table in the ANGLE and
LCUTS columns:
If Q19=0 is defined, the TNC always plunges
perpendicularly, even if a plunge angle (ANGLE) is defined
for the active tool.
If you define the ANGLE=90°, the TNC plunges
perpendicularly. The reciprocation feed rate Q19 is used
as plunging feed rate.
If the reciprocation feed rate Q19 is defined in Cycle 22
and ANGLE is defined between 0.1 and 89.999 in the tool
table, the TNC plunges helically at the defined ANGLE.
If the reciprocation feed is defined in Cycle 22 and no
ANGLE is in the tool table, the TNC displays an error
message.
If geometrical conditions do not allow helical plunging
(slot geometry), the TNC tries a reciprocating plunge.
The reciprocation length is calculated from LCUTS and
ANGLE (reciprocation length = LCUTS / tan ANGLE).
If you clear out an acute inside corner and use an overlap
factor greater than 1, some material might be left over.
Check especially the innermost path in the test run graphic
and, if necessary, change the overlap factor slightly. This
allows another distribution of cuts, which often provides
the desired results.
During fine roughing the TNC does not take a defined wear
value DR of the coarse roughing tool into account.
Feed rate reduction through parameter Q401 is an FCL3
function and is not automatically available after a software
update (see “Feature content level (upgrade functions)”
on page 8).

Cycle parameters
U Plunging depth Q10 (incremental): Infeed per cut. Example: NC blocks
Input range: -99999.9999 to 99999.9999
59 CYCL DEF 22 ROUGH-OUT
U Feed rate for plunging Q11: Plunging feed rate in
mm/min. Input range: 0 to 99999.9999; alternatively Q10=+5 ;PLUNGING DEPTH
FAUTO, FU, FZ. Q11=100 ;FEED RATE FOR PLNGNG
U Feed rate for roughing Q12: Milling feed rate in Q12=750 ;FEED RATE FOR ROUGHING
mm/min. Input range: 0 to 99999.9999; alternatively
FAUTO, FU, FZ. Q18=1 ;COARSE ROUGHING TOOL
Q19=150 ;RECIPROCATION FEED RATE
U Coarse roughing tool Q18 or QS18: Number or name
of the tool with which the TNC has already coarse- Q208=99999 ;RETRACTION FEED RATE
roughed the contour. Switch to name input: Press the
Q401=80 ;FEED RATE REDUCTION
TOOL NAME soft key. The TNC automatically inserts
the closing quotation mark when you exit the input Q404=0 ;FINE ROUGH STRATEGY
field. If there was no coarse roughing, enter “0”; if
you enter a number or a name, the TNC will only
rough-out the portion that could not be machined with
the coarse roughing tool. If the portion that is to be
roughed cannot be approached from the side, the
TNC will mill in a reciprocating plunge-cut; For this
purpose you must enter the tool length LCUTS in the
tool table TOOL.T and define the maximum plunging
ANGLE of the tool. The TNC will otherwise generate an
error message. Input range 0 to 32767.9 if a number
is entered; maximum 16 characters if a name is
entered.
U Reciprocation feed rate Q19: Traversing speed of
the tool in mm/min during reciprocating plunge cut.
FZ.
tool in mm/min when retracting after machining. If
you enter Q208 = 0, the TNC retracts the tool at the
feed rate in Q12. Input range 0 to 99999.9999,
alternatively FMAX, FAUTO, PREDEF.

U Feed rate factor in %: Q401: Percentage factor by
which the TNC reduces the machining feed rate(Q12)
as soon as the tool moves within the material over its
entire circumference during roughing. If you use the
feed rate reduction, then you can define the feed rate
for roughing so large that there are optimum cutting
conditions with the path overlap (Q2) specified in
Cycle 20. The TNC then reduces the feed rate as per
your definition at transitions and narrow places, so
the machining time should be reduced in total. Input
range 0.0001 to 100.0000
U Fine-roughing strategy Q404: Specify how the TNC
should move the tool during fine roughing when the
radius of the fine-roughing tool is larger than half the
coarse roughing tool.
Q404 = 0
Move the tool along the contour at the current
depth between areas that need to be fine-roughed.
Q404 = 1
Between areas that need to be fine-roughed,
retract the tool to safety clearance and move to the
starting point of the next area to be rough-milled.

7.7 FLOOR FINISHING (Cycle 23, DIN/ISO: G123)
7.7 FLOOR FINISHING (Cycle 23,
DIN/ISO: G123)
Cycle run
The tool approaches the machining plane smoothly (on a vertically
tangential arc) if there is sufficient room. If there is not enough room,
the TNC moves the tool to depth vertically. The tool then clears the
finishing allowance remaining from rough-out.
The TNC automatically calculates the starting point for

finishing. The starting point depends on the available
space in the pocket.
The approaching radius for pre-positioning to the final
depth is permanently defined and independent of the
plunging angle of the tool.
Cycle parameters
U Feed rate for plunging Q11: Traversing speed of the
tool during plunging. Input range 0 to 99999.9999,
alternatively FAUTO, FU, FZ
U Feed rate for roughing Q12: Milling feed rate. Input
range 0 to 99999.9999, alternatively FAUTO, FU, FZ
Z
tool in mm/min when retracting after machining. If
you enter Q208 = 0, the TNC retracts the tool at the
feed rate in Q12. Input range 0 to 99999.9999,
alternatively FMAX, FAUTO, PREDEF. X
Q12
Q11
Example: NC blocks
60 CYCL DEF 23 FLOOR FINISHING

Q12=350 ;FEED RATE FOR ROUGHING

7.8 SIDE FINISHING (Cycle 24, DIN/ISO: G124)
7.8 SIDE FINISHING (Cycle 24,
DIN/ISO: G124)
Cycle run
The individual subcontours are approached and departed on a
tangential arc. The TNC finishes each subcontour separately.
The sum of allowance for side (Q14) and the radius of the
finish mill must be smaller than the sum of allowance for
side (Q3, Cycle 20) and the radius of the rough mill.
This calculation also holds if you run Cycle 24 without
having roughed out with Cycle 22; in this case, enter “0”
for the radius of the rough mill.
You can use Cycle 24 also for contour milling. Then you
must:
define the contour to be milled as a single island
(without pocket limit), and
enter the finishing allowance (Q3) in Cycle 20 to be
greater than the sum of the finishing allowance Q14 +
radius of the tool being used.
The TNC automatically calculates the starting point for
finishing. The starting point depends on the available
space in the pocket and the allowance programmed in
Cycle 20. The TNC executes the positioning logic to the
starting point of the finishing operation as follows:
approach the starting point in the working plane, then
move to depth in tool axis direction.
The starting point calculated by the TNC also depends on
the machining sequence. If you select the finishing cycle
with the GOTO key and then start the program, the
starting point can be at a different location from where it
would be if you execute the program in the defined
sequence.

7.8 SIDE FINISHING (Cycle 24, DIN/ISO: G124)
Cycle parameters
U Direction of rotation? Clockwise = –1 Q9:
Machining direction:
+1:Counterclockwise
–1:Clockwise
Alternatively PREDEF Z
Input range: -99999.9999 to 99999.9999
tool during plunging. Input range 0 to 99999.9999, X
Q10 Q12
U Feed rate for roughing Q12: Milling feed rate. Input
U Finishing allowance for side Q14
(incremental): Enter the allowed material for
several finish-milling operations. If you enter
Q14 = 0, the remaining finishing allowance will
Example: NC blocks
be cleared. Input range -99999.9999 to
99999.9999 61 CYCLE DEF 24 SIDE FINISHING
Q9=+1 ;DIRECTION
Q10=+5 ;PLUNGING DEPTH
Q14=+0 ;ALLOWANCE FOR SIDE

7.9 CONTOUR TRAIN (Cycle 25, DIN/ISO: G125)
7.9 CONTOUR TRAIN (Cycle 25,
DIN/ISO: G125)
Cycle run
In conjunction with Cycle 14 CONTOUR GEOMETRY, this cycle facilitates
the machining of open and closed contours.
Z
Cycle 25 CONTOUR TRAIN offers considerable advantages over
machining a contour using positioning blocks: Y
The TNC monitors the operation to prevent undercuts and surface
blemishes. It is recommended that you run a graphic simulation of
the contour before execution.
If the radius of the selected tool is too large, the corners of the
contour may have to be reworked.
The contour can be machined throughout by up-cut or by climb
milling. The type of milling even remains effective when the
contours are mirrored.
The tool can traverse back and forth for milling in several infeeds:
This results in faster machining. X
Allowance values can be entered in order to perform repeated
rough-milling and finish-milling operations.

When you use Cycle 25 CONTOUR TRAIN you can define only
one contour program in Cycle 14 CONTOUR.
The memory capacity for programming an SL cycle is
limited. You can program up to 8192 contour elements in
one SL cycle.
The TNC does not need Cycle 20 CONTOUR DATA in
conjunction with Cycle 25.
The miscellaneous functions M109 and M110 are not
effective when machining a contour with Cycle 25.
To avoid collisions,
Do not program positions in incremental dimensions
immediately after Cycle 25 since they are referenced to
the position of the tool at the end of the cycle.
Move the tool to defined (absolute) positions in all main
axes, since the position of the tool at the end of the
cycle is not identical to the position of the tool at the
start of the cycle.

7.9 CONTOUR TRAIN (Cycle 25, DIN/ISO: G125)
Cycle parameters
U Milling depth Q1 (incremental): Distance between Example: NC blocks
workpiece surface and contour floor. Input range -
99999.9999 to 99999.9999 62 CYCL DEF 25 CONTOUR TRAIN
U Finishing allowance for side Q3 (incremental): Q1=-20 ;MILLING DEPTH

Finishing allowance in the working plane. Input range Q3=+0 ;ALLOWANCE FOR SIDE
-99999.9999 to 99999.9999
Absolute coordinate of the workpiece surface Q7=+50 ;CLEARANCE HEIGHT
referenced to the workpiece datum. Input range: Q10=+5 ;PLUNGING DEPTH
-99999.9999 to 99999.9999
U Clearance height Q7 (absolute): Absolute height at
which the tool cannot collide with the workpiece.
Position for tool retraction at the end of the cycle. Q15=-1 ;CLIMB OR UP-CUT
Input range -99999.9999 to 99999.9999, alternatively
PREDEF
Input range: -99999.9999 to 99999.9999
tool in the spindle axis. Input range 0 to 99999.9999,
tool in the working plane. Input range 0 to
99999.9999, alternatively FAUTO, FU, FZ
U Climb or up-cut? Up-cut = –1 Q15:
Climb milling: Input value = +1
Up-cut milling: Input value = –1
To enable climb milling and up-cut milling alternately
in several infeeds:Input value = 0

7.10 CONTOUR DATA (Cycle 270,
DIN/ISO: G270)
If desired, you can use this cycle to specify various properties of Cycle
25, CONTOUR TRAIN.

Cycle 270 is DEF active, which means that it becomes
The TNC resets Cycle 270 as soon as you define another
SL cycle (with the exception of Cycle 25).
If Cycle 270 is used, do not define any radius
compensation in the contour subprogram.
Approach and departure properties are always performed
identically (symmetrically) by the TNC.
Define Cycle 270 before Cycle 25.

Cycle parameters
U Type of approach/departure Q390: Definition of the Example: NC blocks
type of approach or departure.
62 CYCL DEF 270 CONTOUR TRAIN DATA
Q390 = 1:
Approach the contour tangentially on a circular arc. Q390=1 ;TYPE OF APPROACH
Q390 = 2: Q391=1 ;RADIUS COMPENSATION
Approach the contour tangentially on a straight line. Q392=3 ;RADIUS
Q390 = 3:
Approach the contour at a right angle. Q393=+45 ;CENTER ANGLE
Q394=+2 ;DISTANCE
U Radius compensation (0=R0/1=RL/2=RR) Q391:
Definition of the radius compensation:
Q391 = 0:
Machine the defined contour without radius
compensation
Q391 = 1:
Machine the defined contour with compensation to
the left
Q391 = 2:
Machine the defined contour with compensation to
the right
U Approach/departure radius Q392: Only in effect if
tangential approach on a circular path was selected.
Radius of the approach/departure arc. Input range 0 to
99999.9999
U Center angle Q393: Only in effect if tangential
approach on a circular path was selected. Angular
length of the approach arc. Input range 0 to
99999.9999
U Distance to auxiliary point Q394: Only in effect if
tangential approach on a straight line or right-angle
approach was selected. Distance to the auxiliary point
from which the TNC is to approach the contour. Input
range 0 to 99999.9999

7.11 TROCHOIDAL SLOT (Cycle 275, DIN/ISO: G275)
7.11 TROCHOIDAL SLOT (Cycle 275,
DIN/ISO: G275)
Cycle run
In conjunction with Cycle 14 CONTOUR GEOMETRY, this cycle facilitates Example: TROCHOIDAL SLOT scheme
the complete machining of open and closed slots or contour slots
using trochoidal milling. 0 BEGIN PGM CYC275 MM
With trochoidal milling, large cutting depths and high cutting speeds ...
are possible because the equally distributed cutting conditions prevent 12 CYCL DEF 14.0 CONTOUR GEOMETRY
wear-increasing influences on the tool. When tool inserts are used the
entire cutting length is exploited to increase the attainable chip volume 13 CYCL DEF 14.1 CONTOUR LABEL 10
per tooth. Moreover, trochoidal milling is easy on the machine 14 CYCL DEF 275 TROCHOIDAL SLOT ...
mechanics. Enormous amounts of time can also be saved by
combining this milling method with the integrated adaptive feed 15 CYCL CALL M3
control AFC software option (see User's Manual on conversational ...
programming).
50 L Z+250 R0 FMAX M2
Depending on the cycle parameters you select, the following
machining alternatives are available: 51 LBL 10
...
Complete machining: Roughing, side finishing
Only roughing 55 LBL 0
Only side finishing ...
99 END PGM CYC275 MM

Roughing with closed slots
The contour description of a closed slot must always start with a
straight-line block (L block).
1 Following the positioning logic, the tool moves to the starting point
of the contour description and moves in a reciprocating motion at
the plunging angle defined in the tool table to the first infeed
depth. Specify the plunging strategy with Parameter Q366.
2 The TNC roughs the slot in circular motions to the contour end
point. During the circular motion the TNC moves the tool in
machining direction by an infeed you can define (Q436). Define
climb or up-cut of the circular motion in Parameter Q351.
3 At the contour end point, the TNC moves the tool to clearance
height and returns to the starting point of the contour description.
4 This process is repeated until the programmed slot depth is
reached.
Finishing with closed slots
5 Inasmuch as a finishing allowance is defined, the TNC finishes the
slot walls, in multiple infeeds if so specified. Starting from the
defined starting point, the TNC approaches the slot wall
tangentially. Climb or up-cut are taken into consideration.
Roughing with open slots
The contour description of an open slot must always start with an
approach block (APPR).
1 Following the positioning logic, the tool moves to the starting point
of the machining operation as defined by the parameters in the
APPR block and positions there perpendicular to the first plunging
depth.
2 The TNC roughs the slot in circular motions to the contour end
point. During the circular motion the TNC moves the tool in
machining direction by an infeed you can define (Q436). Define
climb or up-cut of the circular motion in Parameter Q351.
3 At the contour end point, the TNC moves the tool to clearance
height and returns to the starting point of the contour description.
4 This process is repeated until the programmed slot depth is
reached.
Finishing with closed slots
5 Inasmuch as a finishing allowance is defined, the TNC finishes the
slot walls, in multiple infeeds if so specified. Starting from the
defined starting point of the APPR block, the TNC approaches the
slot wall. Climb or up-cut are taken into consideration.


When you use Cycle 275 TROCHOIDAL SLOT, you can define
only one contour program in Cycle 14 CONTOUR GEOMETRY.
Define the center line of the slot with all available path
functions in the contour subprogram.
one SL cycle.
The TNC does not need Cycle 20 CONTOUR DATA in
conjunction with Cycle 275.
The miscellaneous functions M109 and M110 are not
effective when machining a contour with Cycle 275.
To avoid collisions,
Do not program positions in incremental dimensions
immediately after Cycle 275 since they are referenced
to the position of the tool at the end of the cycle.
Move the tool to defined (absolute) positions in all main
axes, since the position of the tool at the end of the
cycle is not identical to the position of the tool at the
start of the cycle.

Cycle parameters
1: Only roughing
Q436
2: Only finishing
The TNC also executes side finishing if the finishing
allowance (Q368) defined is 0.
Q368
U Slot width Q219: Enter the slot width; If you enter a
slot width that equals the tool diameter, the TNC will
only machine the contour outline. Input range 0 to
99999.9999
U Finishing allowance for side Q368 (incremental): Q207
Finishing allowance in the working plane.
U Infeed per rev. Q436 absolute: Value by which the Q219 X
TNC moves the tool in the machining direction per
revolution. Input range: 0 to 99999.9999
M3:
+1 = climb milling

workpiece surface and bottom of slot. Input range -
99999.9999 to 99999.9999
Q206
99999.9999
Q338
range: 0 to 99999.999; alternatively FAUTO, FU, FZ. Q202
Q201
99999.9999
the tool during side finishing in mm/min. Input range: X
0 to 99999.9999; alternatively FAUTO, FU, FZ

range -99999.9999 to 99999.9999
in the spindle axis at which no collision between tool Q204
Q200 Q368
1: No function
2 = reciprocating plunge. In the tool table, the Example: NC blocks
plunging angle ANGLE for the active tool must be
defined as not equal to 0. The TNC will otherwise 8 CYCL DEF 275 TROCHOIDAL SLOT
display an error message. Q215=0 ;MACHINING OPERATION
Alternative: PREDEF
Q219=12 ;SLOT WIDTH
Q436=2 ;INFEED PER REVOLUTION
Q201=-20 ;DEPTH
Q366=2 ;PLUNGE
9 CYCL CALL FMAX M3

Example: Roughing-out and fine-roughing a pocket
10
Y 10
R20
55
R30 60°
30
X
30
0 BEGIN PGM C20 MM

1 BLK FORM 0.1 Z X-10 Y-10 Z-40
2 BLK FORM 0.2 X+100 Y+100 Z+0 Definition of workpiece blank
3 TOOL CALL 1 Z S2500 Tool call: coarse roughing tool, diameter 30
5 CYCL DEF 14.0 CONTOUR GEOMETRY Define contour subprogram
6 CYCL DEF 14.1 CONTOUR LABEL 1
7 CYCL DEF 20 CONTOUR DATA Define general machining parameters
Q1=-20 ;MILLING DEPTH
Q4=+0 ;ALLOWANCE FOR FLOOR
Q9=-1 ;DIRECTION

8 CYCL DEF 22 ROUGH-OUT Cycle definition: Coarse roughing
Q18=0 ;COARSE ROUGHING TOOL
Q401=100 ;FEED RATE FACTOR
Q404=0 ;FINE ROUGH STRATEGY
9 CYCL CALL M3 Cycle call: Coarse roughing
10 L Z+250 R0 FMAX M6 Tool change
11 TOOL CALL 2 Z S3000 Tool call: fine roughing tool, diameter 15
12 CYCL DEF 22 ROUGH-OUT Define the fine roughing cycle
13 CYCL CALL M3 Cycle call: Fine roughing
15 LBL 1 Contour subprogram

16 L X+0 Y+30 RR
17 FC DR- R30 CCX+30 CCY+30
18 FL AN+60 PDX+30 PDY+30 D10
19 FSELECT 3
20 FPOL X+30 Y+30
21 FC DR- R20 CCPR+55 CCPA+60
22 FSELECT 2
23 FL AN-120 PDX+30 PDY+30 D10
24 FSELECT 3
25 FC X+0 DR- R30 CCX+30 CCY+30
26 FSELECT 2
27 LBL 0
28 END PGM C20 MM

Example: Pilot drilling, roughing-out and finishing overlapping contours
Y
16 16
100
R2
5
50
16
5
R2
X
35 65 100
0 BEGIN PGM C21 MM

2 BLK FORM 0.2 X+100 Y+100 Z+0
3 TOOL CALL 1 Z S2500 Tool call: Drill, diameter 12
6 CYCL DEF 14.1 CONTOUR LABEL1/2/3/4
Q9=-1 ;DIRECTION

8 CYCL DEF 21 PILOT DRILLING Cycle definition: Pilot drilling
Q13=2 ;ROUGH-OUT TOOL
9 CYCL CALL M3 Cycle call: Pilot drilling
10 L +250 R0 FMAX M6 Tool change
11 TOOL CALL 2 Z S3000 Call the tool for roughing/finishing, diameter 12
12 CYCL DEF 22 ROUGH-OUT Cycle definition: Rough-out
13 CYCL CALL M3 Cycle call: Rough-out
14 CYCL DEF 23 FLOOR FINISHING Cycle definition: Floor finishing
15 CYCL CALL Cycle call: Floor finishing
16 CYCLE DEF 24 SIDE FINISHING Cycle definition: Side finishing
Q9=+1 ;DIRECTION
17 CYCL CALL Cycle call: Side finishing

19 LBL 1 Contour subprogram 1: left pocket
20 CC X+35 Y+50
21 L X+10 Y+50 RR
22 C X+10 DR-
23 LBL 0
24 LBL 2 Contour subprogram 2: right pocket
25 CC X+65 Y+50
26 L X+90 Y+50 RR
27 C X+90 DR-
28 LBL 0
29 LBL 3 Contour subprogram 3: square left island
30 L X+27 Y+50 RL
31 L Y+58
32 L X+43
33 L Y+42
34 L X+27
35 LBL 0
36 LBL 4 Contour subprogram 4: triangular right island
39 L X+65 Y+42 RL
37 L X+57
38 L X+65 Y+58
39 L X+73 Y+42
40 LBL 0
41 END PGM C21 MM

Example: Contour train
Y
100
95
R7
R7,5
,5
80
75
20
15
X
5 50 100
0 BEGIN PGM C25 MM

2 BLK FORM 0.2 X+100 Y+100 Z+0
3 TOOL CALL 1 Z S2000 Tool call: Diameter 20
7 CYCL DEF 25 CONTOUR TRAIN Define machining parameters
8 CYCL CALL M3 Cycle call

11 L X+0 Y+15 RL
12 L X+5 Y+20
13 CT X+5 Y+75
14 L Y+95
15 RND R7.5
16 L X+50
17 RND R7.5
18 L X+100 Y+80
19 LBL 0
20 END PGM C25 MM


Fixed Cycles: Cylindrical
Surface
8.1 Basics
8.1 Basics
Overview of cylindrical surface cycles
Cycle Soft key Page

27 CYLINDER SURFACE Page 221
28 CYLINDER SURFACE slot milling Page 224
29 CYLINDER SURFACE ridge milling Page 227
39 CYLINDER SURFACE outside Page 230

contour milling
220 Fixed Cycles: Cylindrical Surface

8.2 CYLINDER SURFACE (Cycle 27, DIN/ISO: G127, Software Option 1)
8.2 CYLINDER SURFACE (Cycle 27,
DIN/ISO: G127, Software
Option 1)
Execution of cycle
This cycle enables you to program a contour in two dimensions and
then roll it onto a cylindrical surface for 3-D machining. Use Cycle 28 if
you want to mill guideways on the cylinder.
The contour is described in a subprogram identified in Cycle 14
CONTOUR GEOMETRY.
The subprogram contains coordinates in a rotary axis and in its parallel
axis. The rotary axis C, for example, is parallel to the Z axis. The path
functions L, CHF, CR, RND, APPR (except for APPR LCT) and DEP are
available.
The dimensions in the rotary axis can be entered as desired either in
degrees or in mm (or inches). You can select the desired dimension
type in the cycle definition.
1 The TNC positions the tool over the cutter infeed point, taking the
allowance for side into account.
2 At the first plunging depth, the tool mills along the programmed
contour at the milling feed rate Q12.
3 At the end of the contour, the TNC returns the tool to the setup
clearance and returns to the point of penetration.
Z
4 Steps 1 to 3 are repeated until the programmed milling depth Q1
is reached.
5 Then the tool moves to the setup clearance.

The machine and TNC must be prepared for cylinder

surface interpolation by the machine tool builder. Refer to
your machine tool manual.
In the first NC block of the contour program, always

program both cylinder surface coordinates.
one SL cycle.
This cycle requires a center-cut end mill (DIN 844).
The cylinder must be set up centered on the rotary table.
The tool axis must be perpendicular to the rotary table. If
this is not the case, the TNC will generate an error
message.
This cycle can also be used in a tilted working plane.

Cycle parameters
the cylindrical surface and the floor of the contour.
Input range: -99999.9999 to 99999.9999 63 CYCL DEF 27 CYLINDER SURFACE

Finishing allowance in the plane of the unrolled Q3=+0 ;ALLOWANCE FOR SIDE
cylindrical surface. This allowance is effective in
the direction of the radius compensation. Input Q6=+0 ;SETUP CLEARANCE
range -99999.9999 to 99999.9999 Q10=+3 ;PLUNGING DEPTH
U Setup clearance Q6 (incremental): Distance between Q11=100 ;FEED RATE FOR PLNGNG
the tool tip and the cylinder surface. Input range 0 to
99999.9999, alternatively PREDEF Q12=350 ;FEED RATE FOR MILLING
Q16=25 ;RADIUS
Input range: -99999.9999 to 99999.9999 Q17=0 ;TYPE OF DIMENSION
U Cylinder radius Q16: Radius of the cylinder on which
the contour is to be machined. Input range 0 to
99999.9999
U Dimension type? ang./lin. Q17: The dimensions for
the rotary axis of the subprogram are given either in
degrees (0) or in mm/inches (1).

Option 1)
8.3 CYLINDER SURFACE Slot Milling (Cycle 28, DIN/ISO: G128, Software
8.3 CYLINDER SURFACE Slot Milling
(Cycle 28, DIN/ISO: G128,
Software Option 1)
Cycle run
This cycle enables you to program a guide notch in two dimensions
and then transfer it onto a cylindrical surface. Unlike Cycle 27, with this
cycle the TNC adjusts the tool so that, with radius compensation
active, the walls of the slot are nearly parallel. You can machine exactly
parallel walls by using a tool that is exactly as wide as the slot.
The smaller the tool is with respect to the slot width, the larger the
distortion in circular arcs and oblique line segments. To minimize this
process-related distortion, you can define in parameter Q21 a
tolerance with which the TNC machines a slot as similar as possible to
a slot machined with a tool of the same width as the slot.
Program the midpoint path of the contour together with the tool radius
compensation. With the radius compensation you specify whether the
TNC cuts the slot with climb milling or up-cut milling.
1 The TNC positions the tool over the cutter infeed point.
slot wall at the milling feed rate Q12 while respecting the finishing
allowance for the side.
3 At the end of the contour, the TNC moves the tool to the opposite
wall and returns to the infeed point. Z
4 Steps 2 and 3 are repeated until the programmed milling depth Q1
is reached.
5 If you have defined the tolerance in Q21, the TNC then remachines
the slot walls to be as parallel as possible.
6 Finally, the tool retracts in the tool axis to the clearance height or
to the position last programmed before the cycle (depending on
machine parameter 7420).

Option 1)


one SL cycle.
This cycle requires a center-cut end mill (DIN 844).
message.

Option 1)
Cycle parameters
Input range: -99999.9999 to 99999.9999 63 CYCL DEF 28 CYLINDER SURFACE

Finishing allowance on the slot wall. The finishing Q3=+0 ;ALLOWANCE FOR SIDE
allowance reduces the slot width by twice the
entered value. Input range -99999.9999 to Q6=+0 ;SETUP CLEARANCE
99999.9999 Q10=+3 ;PLUNGING DEPTH
Q16=25 ;RADIUS
U Feed rate for plunging Q11: Traversing speed of the Q20=12 ;SLOT WIDTH
tool in the spindle axis. Input range 0 to 99999.9999, Q21=0 ;TOLERANCE
99999.9999
U Slot width Q20: Width of the slot to be machined.
Input range -99999.9999 to 99999.9999
U Tolerance? Q21: If you use a tool smaller than the
programmed slot width Q20, process-related
distortion occurs on the slot wall wherever the slot
follows the path of an arc or oblique line. If you define
the tolerance Q21, the TNC adds a subsequent
milling operation to ensure that the slot dimensions
are a close as possible to those of a slot that has been
milled with a tool exactly as wide as the slot. With
Q21 you define the permitted deviation from this
ideal slot. The number of subsequent milling
operations depends on the cylinder radius, the tool
used, and the slot depth. The smaller the tolerance is
defined, the more exact the slot is and the longer the
remachining takes. Recommendation: Use a
tolerance of 0.02 mm. Function inactive: Enter 0
(default setting) Input range 0 to 9.9999

8.4 CYLINDER SURFACE Ridge Milling (Cycle 29, DIN/ISO: G129, Software
Option 1)
8.4 CYLINDER SURFACE Ridge
Milling (Cycle 29, DIN/ISO:
G129, Software Option 1)
Cycle run
This cycle enables you to program a ridge in two dimensions and then
transfer it onto a cylindrical surface. With this cycle the TNC adjusts
the tool so that, with radius compensation active, the walls of the slot
are always parallel. Program the midpoint path of the ridge together
with the tool radius compensation. With the radius compensation you
specify whether the TNC cuts the ridge with climb milling or up-cut
milling.
At the ends of the ridge the TNC always adds a semicircle whose
radius is half the ridge width.
1 The TNC positions the tool over the starting point of machining.
The TNC calculates the starting point from the ridge width and the
tool diameter. It is located next to the first point defined in the
contour subprogram, offset by half the ridge width and the tool
diameter. The radius compensation determines whether
machining begins from the left (1, RL = climb milling) or the right
of the ridge (2, RR = up-cut milling).
2 After the TNC has positioned to the first plunging depth, the tool
moves on a circular arc at the milling feed rate Q12 tangentially to
the ridge wall. If so programmed, it will leave metal for the finishing
allowance. Z
ridge wall at the milling feed rate Q12 until the stud is completed.
4 The tool then departs the ridge wall on a tangential path and
returns to the starting point of machining.
is reached.
to the position last programmed before the cycle (depending on 1 2

Option 1) Please note while programming:


Ensure that the tool has enough space laterally for contour
approach and departure.
one SL cycle.
message.

Option 1)
Cycle parameters
Input range: -99999.9999 to 99999.9999 63 CYCL DEF 29 CYLINDER SURFACE RIDGE

Finishing allowance on the ridge wall. The finishing Q3=+0 ;ALLOWANCE FOR SIDE
allowance increases the ridge width by twice the
entered value. Input range: -99999.9999 to Q6=+0 ;SETUP CLEARANCE
99999.9999 Q10=+3 ;PLUNGING DEPTH
Q16=25 ;RADIUS
U Feed rate for plunging Q11: Traversing speed of the Q20=12 ;RIDGE WIDTH
99999.9999
U Ridge width Q20: Width of the ridge to be machined.
Input range -99999.9999 to 99999.9999

8.5 CYLINDER SURFACE Outside Contour Milling (Cycle 39, DIN/ISO: G139,
Software Option 1) 8.5 CYLINDER SURFACE Outside
Contour Milling (Cycle 39,
Option 1)
Cycle run
This cycle enables you to program an open contour in two dimensions
and then roll it onto a cylindrical surface for 3-D machining. With this
cycle the TNC adjusts the tool so that, with radius compensation
active, the wall of the open contour is always parallel to the cylinder
axis.
Unlike Cycles 28 and 29, in the contour subprogram you define the
actual contour to be machined.
1 The TNC positions the tool over the starting point of machining.
The TNC locates the starting point next to the first point defined in
the contour subprogram, offset by the tool diameter (standard
behavior).
2 After the TNC has positioned to the first plunging depth, the tool
moves on a circular arc at the milling feed rate Q12 tangentially to
the contour. If so programmed, it will leave metal for the finishing
allowance.
contour at the milling feed rate Q12 until the contour train is
completed.
4 The tool then departs the ridge wall on a tangential path and
returns to the starting point of machining.
is reached.
to the position last programmed before the cycle (depending on
You can define the approach behavior of Cycle 39 in

Machine Parameter 7680, bit 16.
Bit 16 = 0:
Tangential approach and departure
Bit 16 = 1:
Move to depth vertically at the starting point of the
contour without tangential tool approach and move up at
the contour end point without tangential departure.

Software Option 1)


Ensure that the tool has enough space laterally for contour
approach and departure.
one SL cycle.
message.

Software Option 1) Cycle parameters
Input range: -99999.9999 to 99999.9999 63 CYCL DEF 39 CYL. SURFACE CONTOUR

Finishing allowance on the contour wall. Input range: Q3=+0 ;ALLOWANCE FOR SIDE
-99999.9999 to 99999.9999
Q6=+0 ;SETUP CLEARANCE
U Setup clearance Q6 (incremental): Distance between
the tool tip and the cylinder surface. Input range 0 to Q10=+3 ;PLUNGING DEPTH
99999.9999, alternatively PREDEF Q11=100 ;FEED RATE FOR PLNGNG
U Plunging depth Q10 (incremental): Infeed per cut. Q12=350 ;FEED RATE FOR MILLING
Input range: -99999.9999 to 99999.9999
Q16=25 ;RADIUS
U Feed rate for plunging Q11: Traversing speed of the Q17=0 ;TYPE OF DIMENSION
99999.9999

Example: Cylinder surface with Cycle 27
Note:
Machine with B head and C table
Cylinder centered on rotary table Z
Datum at center of rotary table
.5
R7
60
20
C
30 50 157
0 BEGIN PGM C27 MM

1 TOOL CALL 1 Z S2000 Tool call: Diameter 7
3 L X+50 Y0 R0 FMAX Pre-position tool on rotary table center
4 PLANE SPATIAL SPA+0 SPB+90 SPC+0 Positioning
TURN MBMAX FMAX
7 CYCL DEF 27 CYLINDER SURFACE Define machining parameters
Q16=25 ;RADIUS
Q17=1 ;TYPE OF DIMENSION

8 L C+0 R0 FMAX M13 M99 Pre-position rotary table, spindle ON, call the cycle
10 PLANE RESET TURN FMAX Tilt back, cancel the PLANE function
11 M2 End of program
13 L C+40 X+20 RL Data for the rotary axis are entered in mm (Q17=1), traverse in the X
axis because of 90° tilting
14 L C+50
15 RND R7.5
16 L X+60
17 RND R7.5
18 L IC-20
19 RND R7.5
20 L X+20
21 RND R7.5
22 L C+40
23 LBL 0
24 END PGM C27 MM

Example: Cylinder surface with Cycle 28
Notes:
Cylinder centered on rotary table
Machine with B head and C table Z
Datum at center of rotary table
Description of the midpoint path in the 70
contour subprogram
52.5
35
C
40 60 157
0 BEGIN PGM C28 MM

1 TOOL CALL 1 Z S2000 Tool call, tool axis Z, diameter 7
3 I X+50 Y+0 R0 FMAX Position tool on rotary table center
4 PLANE SPATIAL SPA+0 SPB+90 SPC+0 Positioning
TURN FMAX
7 CYCL DEF 28 CYLINDER SURFACE Define machining parameters
Q10=-4 ;PLUNGING DEPTH
Q16=25 ;RADIUS
Q17=1 ;TYPE OF DIMENSION
Q20=10 ;SLOT WIDTH
Q21=0.02 ;TOLERANCE Remachining active

8 L C+0 R0 FMAX M3 M99 Pre-position rotary table, spindle ON, call the cycle
10 PLANE RESET TURN FMAX Tilt back, cancel the PLANE function
11 M2 End of program
12 LBL 1 Contour subprogram, description of the midpoint path
13 L C+40 X+0 RL Data for the rotary axis are entered in mm (Q17=1), traverse in the X
axis because of 90° tilting
14 L X+35
15 L C+60 X+52.5
16 L X+70
17 LBL 0
18 END PGM C28 MM

Fixed Cycles: Contour
Pocket with Contour
Formula
9.1 SL Cycles with Complex Contour Formula
9.1 SL Cycles with Complex
Contour Formula
Basics
SL cycles and the complex contour formula enable you to form Example: Program structure: Machining with SL
complex contours by combining subcontours (pockets or islands). You cycles and complex contour formula
define the individual subcontours (geometry data) as separate
programs. In this way, any subcontour can be used any number of 0 BEGIN PGM CONTOUR MM
times. The TNC calculates the complete contour from the selected ...
subcontours, which you link together through a contour formula.
5 SEL CONTOUR “MODEL“
The memory capacity for programming an SL cycle (all 6 CYCL DEF 20 CONTOUR DATA...
contour description programs) is limited to 128 contours.
The number of possible contour elements depends on the 8 CYCL DEF 22 ROUGH-OUT...
type of contour (inside or outside contour) and the number 9 CYCL CALL
of contour descriptions. You can program up to 16384
elements. ...
The SL cycles with contour formula presuppose a 12 CYCL DEF 23 FLOOR FINISHING...
structured program layout and enable you to save 13 CYCL CALL
frequently used contours in individual programs. Using the
contour formula, you can connect the subcontours to a ...
complete contour and define whether it applies to a 16 CYCL DEF 24 SIDE FINISHING...
pocket or island.
17 CYCL CALL
In its present form, the “SL cycles with contour formula”
63 L Z+250 R0 FMAX M2
function requires input from several areas in the TNC’s
user interface. This function is to serve as a basis for 64 END PGM CONTOUR MM
further development.
238 Fixed Cycles: Contour Pocket with Contour Formula

Example: Program structure: Calculation of the

Properties of the subcontours
subcontours with contour formula
By default, the TNC assumes that the contour is a pocket. Do not
program a radius compensation. In the contour formula you can 0 BEGIN PGM MODEL MM
convert a pocket to an island by making it negative.
1 DECLARE CONTOUR QC1 = “CIRCLE1“
The TNC ignores feed rates F and miscellaneous functions M.
Coordinate transformations are allowed. If they are programmed 2 DECLARE CONTOUR QC2 = “CIRCLE31XY“
within the subcontour they are also effective in the following 3 DECLARE CONTOUR QC3 = “TRIANGLE“
4 DECLARE CONTOUR QC4 = “SQUARE“
Although the subprograms can contain coordinates in the spindle
axis, such coordinates are ignored. 5 QC10 = ( QC1 | QC3 | QC4 ) \ QC2
The working plane is defined in the first coordinate block of the 6 END PGM MODEL MM
subprogram. The secondary axes U,V,W are permitted.
Characteristics of the fixed cycles 0 BEGIN PGM CIRCLE1 MM
The TNC automatically positions the tool to the setup clearance 1 CC X+75 Y+50
before a cycle.
2 LP PR+45 PA+0
cutter traverses around islands instead of over them. 3 CP IPA+360 DR+
The radius of “inside corners” can be programmed—the tool keeps 4 END PGM CIRCLE1 MM
moving to prevent surface blemishes at inside corners (this applies
for the outermost pass in the Rough-out and Side Finishing cycles).
The contour is approached on a tangential arc for side finishing. 0 BEGIN PGM CIRCLE31XY MM
For floor finishing, the tool again approaches the workpiece on a ...
plane). ...
With Machine Parameter 7420 you can determine where

the tool is positioned at the end of Cycles 21 to 24.


Selecting a program with contour definitions
With the SEL CONTOUR function you select a program with contour
definitions, from which the TNC takes the contour descriptions:
U Show the soft-key row with special functions.
U Select the menu for functions for contour and point

machining.
U Press the SEL CONTOUR soft key.
U Press the WINDOW SELECTION soft key: The TNC

U Select a program with the arrow keys or by mouse
click and confirm by pressing ENT: The TNC enters
the complete path name in the SEL CONTOUR block.
U Conclude this function with the END key.
U Enter the full name of the program with the contour
definition and confirm with the END key.
Alternatively you can also enter the program name or the complete
path name of the program with the contour definition directly via the
keyboard.
Program a SEL CONTOUR block before the SL cycles. Cycle

14 CONTOUR GEOMETRY is no longer necessary if you use SEL
CONTOUR.

Defining contour descriptions
With the DECLARE CONTOUR function you enter in a program the path for
programs from which the TNC draws the contour descriptions. In
addition, you can select a separate depth for this contour description
(FCL 2 function):

machining.
U Press the DECLARE CONTOUR soft key.
U Enter the number for the contour designator QC, and
confirm with the ENT key.
program to be called.
U Select the program with the contour description with
the arrow keys or by mouse click and confirm by
pressing ENT: The TNC enters the complete path
name in the SEL CONTOUR block.
U Define a separate depth for the selected contour.
Alternatively you can also enter the name of the program with the
contour description or the complete path name of the program directly
via the keyboard.
With the given contour designators QC you can include the

various contours in the contour formula.
If you program separate depths for contours, then you
must assign a depth to all subcontours (assign the depth 0
if necessary).

Entering a complex contour formula
You can use soft keys to interlink various contours in a mathematical
formula.

machining.
U Press the CONTOUR FORMULA soft key. The TNC
then displays the following soft keys:
Mathematical function Soft key

Intersected with
e.g. QC10 = QC1 & QC5
Joined with
e.g. QC25 = QC7 | QC18
Joined without intersection

e.g. QC12 = QC5 ^ QC25
Intersected with complement of

e.g. QC25 = QC1 \ QC2
Complement of the contour area

e.g. QC12 = #QC11
Opening parenthesis
e.g. QC12 = QC1 * (QC2 + QC3)
Closing parenthesis
e.g. QC12 = QC1 * (QC2 + QC3)
Defining a single contour

e.g. QC12 = QC1

Overlapping contours
By default, the TNC considers a programmed contour to be a pocket.
With the functions of the contour formula, you can convert a contour
from a pocket to an island.
Pockets and islands can be overlapped to form a new contour. You can
thus enlarge the area of a pocket by another pocket or reduce it by an
island. B
Subprograms: overlapping pockets

A
The following programming examples are contour
description programs that are defined in a contour
definition program. The contour definition program is
called through the SEL CONTOUR function in the actual main
program.
Pockets A and B overlap.

The TNC calculates the points of intersection S1 and S2 (they do not
have to be programmed).
The pockets are programmed as full circles.

Contour description program 1: pocket A
0 BEGIN PGM POCKET_A MM
1 L X+10 Y+50 R0
2 CC X+35 Y+50
3 C X+10 Y+50 DR-
4 END PGM POCKET_A MM
Contour description program 2: pocket B

0 BEGIN PGM POCKET_B MM
1 L X+90 Y+50 R0
2 CC X+65 Y+50
3 C X+90 Y+50 DR-
4 END PGM POCKET_B MM
Area of inclusion
Both surfaces A and B are to be machined, including the overlapping
area:
The surfaces A and B must be programmed in separate programs
without radius compensation.
In the contour formula, the surfaces A and B are processed with the
“joined with” function. B
Contour definition program:

A
50 ...
51 ...
52 DECLARE CONTOUR QC1 = “POCKET_A.H“
53 DECLARE CONTOUR QC2 = “POCKET_B.H“
54 QC10 = QC1 | QC2
55 ...
56 ...

Area of exclusion
Surface A is to be machined without the portion overlapped by B:
The surfaces A and B must be entered in separate programs without
radius compensation.
In the contour formula, the surface B is subtracted from the surface
A with the “joined with complement of” function.
Contour definition program: B
50 ... A
51 ...
54 QC10 = QC1 \ QC2
55 ...
56 ...
Area of intersection
Only the area where A and B overlap is to be machined. (The areas
covered by A or B alone are to be left unmachined.)
The surfaces A and B must be entered in separate programs without
radius compensation.
In the contour formula, the surfaces A and B are processed with the
“intersection with” function. A B
Contour definition program:
50 ...
51 ...
54 QC10 = QC1 & QC2
55 ...
56 ...
Contour machining with SL Cycles
The complete contour is machined with the SL Cycles 20

to 24 (see “Overview” on page 184).

Example: Roughing and finishing superimposed contours with the contour formula
Y
16 16
100
R2
5
50
16
5
R2
X
35 65 100
0 BEGIN PGM CONTOUR MM

2 BLK FORM 0.2 X+100 Y+100 Z+0
3 TOOL DEF 1 L+0 R+2.5 Tool definition of roughing cutter
4 TOOL DEF 2 L+0 R+3 Tool definition of finishing cutter
5 TOOL CALL 1 Z S2500 Tool call of roughing cutter
7 SEL CONTOUR “MODEL“ Specify contour definition program
Q9=-1 ;DIRECTION
9 CYCL DEF 22 ROUGH-OUT Cycle definition: Rough-out

10 CYCL CALL M3 Cycle call: Rough-out
11 TOOL CALL 2 Z S5000 Tool call of finishing cutter
12 CYCL DEF 23 FLOOR FINISHING Cycle definition: Floor finishing
13 CYCL CALL M3 Cycle call: Floor finishing
14 CYCLE DEF 24 SIDE FINISHING Cycle definition: Side finishing
Q9=+1 ;DIRECTION
15 CYCL CALL M3 Cycle call: Side finishing
17 END PGM CONTOUR MM
Contour definition program with contour formula:
0 BEGIN PGM MODEL MM Contour Definition Program

1 DECLARE CONTOUR QC1 = “CIRCLE1“ Definition of the contour designator for the program “CIRCLE1“
2 FN 0: Q1 =+35 Assignment of values for parameters used in PGM “CIRCLE31XY”
3 FN 0: Q2 = +50
4 FN 0: Q3 =+25
5 DECLARE CONTOUR QC2 = “CIRCLE31XY“ Definition of the contour designator for the program “CIRCLE31XY”
6 DECLARE CONTOUR QC3 = “TRIANGLE“ Definition of the contour designator for the program “TRIANGLE”
7 DECLARE CONTOUR QC4 = “SQUARE“ Definition of the contour designator for the program “SQUARE”
8 QC10 = ( QC 1 | QC 2 ) \ QC 3 \ QC 4 Contour formula
9 END PGM MODEL MM

Contour description programs:
0 BEGIN PGM CIRCLE1 MM Contour description program: circle at right

1 CC X+65 Y+50
2 L PR+25 PA+0 R0
3 CP IPA+360 DR+
4 END PGM CIRCLE1 MM
0 BEGIN PGM CIRCLE31XY MM Contour description program: circle at left

1 CC X+Q1 Y+Q2
2 LP PR+Q3 PA+0 R0
3 CP IPA+360 DR+
4 END PGM CIRCLE31XY MM
0 BEGIN PGM TRIANGLE MM Contour description program: triangle at right

1 L X+73 Y+42 R0
2 L X+65 Y+58
3 L X+58 Y+42
4 L X+73
5 END PGM TRIANGLE MM
0 BEGIN PGM SQUARE MM Contour description program: square at left

1 L X+27 Y+58 R0
2 L X+43
3 L Y+42
4 L X+27
5 L Y+58
6 END PGM SQUARE MM

9.2 SL Cycles with Simple Contour Formula
9.2 SL Cycles with Simple Contour
Formula
Fundamentals
SL cycles and the simple contour formula enable you to form contours Example: Program structure: Machining with SL
by combining up to 9 subcontours (pockets or islands) in a simple cycles and complex contour formula
manner. You define the individual subcontours (geometry data) as
separate programs. In this way, any subcontour can be used any 0 BEGIN PGM CONTDEF MM
number of times. The TNC calculates the contour from the selected ...
subcontours.
5 CONTOUR DEF
The memory capacity for programming an SL cycle (all P1= “POCK1.H”
contour description programs) is limited to 128 contours. I2 = “ISLE2.H“ DEPTH5
The number of possible contour elements depends on the I3 “ISLE3.H“ DEPTH7.5
type of contour (inside or outside contour) and the number
6 CYCL DEF 20 CONTOUR DATA...
of contour descriptions. You can program up to 16384
elements. 8 CYCL DEF 22 ROUGH-OUT...
9 CYCL CALL
Properties of the subcontours ...
By default, the TNC assumes that the contour is a pocket. Do not 12 CYCL DEF 23 FLOOR FINISHING...
program a radius compensation.
13 CYCL CALL
The TNC ignores feed rates F and miscellaneous functions M.
Coordinate transformations are allowed. If they are programmed ...
within the subcontour they are also effective in the following 16 CYCL DEF 24 SIDE FINISHING...
17 CYCL CALL
Although the subprograms can contain coordinates in the spindle
axis, such coordinates are ignored. 63 L Z+250 R0 FMAX M2
The working plane is defined in the first coordinate block of the 64 END PGM CONTDEF MM
subprogram. The secondary axes U,V,W are permitted.

Characteristics of the fixed cycles
The TNC automatically positions the tool to the setup clearance
before a cycle.
cutter traverses around islands instead of over them.
The radius of “inside corners” can be programmed—the tool keeps
moving to prevent surface blemishes at inside corners (this applies
for the outermost pass in the Rough-out and Side Finishing cycles).
The contour is approached on a tangential arc for side finishing.
For floor finishing, the tool again approaches the workpiece on a
plane).
With Machine Parameter 7420 you can determine where

the tool is positioned at the end of Cycles 21 to 24.


Entering a simple contour formula
You can use soft keys to interlink various contours in a mathematical
formula.

machining.
U Press the CONTOUR DEF soft key. The TNC opens
the dialog for entering the contour formula.
U Select the name of the first subcontour with the
WINDOW SELECTION soft key or enter it directly.
The first subcontour must always be the deepest
pocket. Confirm with the ENT key.
U Specify via soft key whether the next subcontour is a
pocket or an island. Confirm with the ENT key.
U Select the name of the second subcontour with the
WINDOW SELECTION soft key or enter it directly.
Confirm by pressing the ENT key.
U If needed, enter the depth of the second subcontour.
Confirm with the ENT key.
U Carry on with the dialog as described above until you
have entered all subcontours.
As a rule, always start the list of subcontours with the

deepest pocket!
If the contour is defined as an island, the TNC interprets
the entered depth as the island height. The entered
value (without an algebraic sign) then refers to the
workpiece top surface!
If the depth is entered as 0, then for pockets the depth
defined in the Cycle 20 is effective. Islands then rise up
to the workpiece top surface!
Contour machining with SL Cycles
The complete contour is machined with the SL Cycles 20

to 24 (see “Overview” on page 184).


Fixed Cycles: Multipass
Milling
10.1 Basics
10.1 Basics
Overview
The TNC offers four cycles for machining surfaces with the following
characteristics:
Created with a CAD/CAM system
Flat, rectangular surfaces
Flat, oblique-angled surfaces
Surfaces that are inclined in any way
Twisted surfaces
Cycle Soft key Page
30 RUN 3-D DATA Page 255
For multipass milling of 3-D data in
several infeeds
230 MULTIPASS MILLING Page 257

For flat rectangular surfaces
231 RULED SURFACE Page 259

For oblique, inclined or twisted surfaces
232 FACE MILLING Page 263

For level rectangular surfaces, with
indicated oversizes and multiple infeeds
254 Fixed Cycles: Multipass Milling

10.2 RUN 3-D DATA (Cycle 30, DIN/ISO: G60)
10.2 RUN 3-D DATA (Cycle 30,
DIN/ISO: G60)
Cycle run
1 From the current position, the TNC positions the tool at rapid
traverse FMAX in the tool axis to the setup clearance above the MAX
point that you have programmed in the cycle.
2 The tool then moves at FMAX in the working plane to the MIN point
you have programmed in the cycle.
3 From this point, the tool advances to the first contour point at the
feed rate for plunging.
4 The TNC subsequently processes all points that are stored in the
digitizing data file at the feed rate for milling. If necessary, the
TNC retracts the tool between machining operations to the setup
clearance if specific areas are to be left unmachined.
5 At the end of the cycle, the tool is retracted at FMAX to the setup
clearance.
You can particularly use Cycle 30 to run conversational

programs created offline in multiple infeeds.

10.2 RUN 3-D DATA (Cycle 30, DIN/ISO: G60)
Cycle parameters
U PGM name 3-D data: Enter the name of the program in
which the contour data is stored. If the file is not
stored in the current directory, enter the complete
Y
path. A maximum of 254 characters can be entered. MAX
U Min. point of range: Lowest coordinates (X, Y and

Z coordinates) in the range to be milled. Input range
-99999.9999 to 99999.9999
U Max. point of range: Largest coordinates (X, Y and 4
Z coordinates) in the range to be milled. Input range
-99999.9999 to 99999.9999
U Setup clearance 1 (incremental): Distance between
tool tip and workpiece surface for tool movements at
rapid traverse. Input range 0 to 99999.9999
MIN X
U Plunging depth 2 (incremental value): Infeed per cut
Input range: -99999.9999 to 99999.9999
U Feed rate for plunging 3: Traversing speed of the
tool during plunging in mm/min. Input range: 0 to
99999.999; alternatively FAUTO.
U Feed rate for plunging 4: Traversing speed of the 3
99999.9999; alternatively FAUTO. Z
U Miscellaneous function M: Optional entry of one to
two miscellaneous functions, for example M13. Input 1
range 0 to 999
2 X
Example: NC blocks
64 CYCL DEF 30.0 RUN 3-D DATA

65 CYCL DEF 30.1 PGM DIGIT.: BSP.H
66 CYCL DEF 30.2 X+0 Y+0 Z-20
67 CYCL DEF 30.3 X+100 Y+100 Z+0
68 CYCL DEF 30.4 SETUP 2
69 CYCL DEF 30.5 PECKG -5 F100
70 CYCL DEF 30.6 F350 M8

10.3 MULTIPASS MILLING (Cycle 230, DIN/ISO: G230)
10.3 MULTIPASS MILLING (Cycle 230,
DIN/ISO: G230)
Cycle run
1 From the current position in the working plane, the TNC positions
the tool at rapid traverse FMAX to the starting point 1; the TNC
moves the tool by its radius to the left and upward. Z
2 The tool then moves at FMAX in the tool axis to the setup clearance.
From there it approaches the programmed starting position in the
tool axis at the feed rate for plunging.
3 The tool then moves at the programmed feed rate for milling to the
end point 2. The TNC calculates the end point from the
Y
programmed starting point, the program length, and the tool 2
radius.
4 The TNC offsets the tool to the starting point in the next pass at
the stepover feed rate. The offset is calculated from the 1 X
programmed width and the number of cuts.
5 The tool then returns in the negative direction of the first axis.
6 Multipass milling is repeated until the programmed surface has
been completed.
7 At the end of the cycle, the tool is retracted at FMAX to the setup
clearance.
From the current position, the TNC positions the tool at

the starting point, first in the working plane and then in the
spindle axis.
Pre-position the tool in such a way that no collision
between tool and clamping devices can occur.

10.3 MULTIPASS MILLING (Cycle 230, DIN/ISO: G230)
Cycle parameters
U Starting point in 1st axis Q225 (absolute):
Minimum point coordinate of the surface to be Y
multipass-milled in the reference axis of the working Q207
plane. Input range -99999.9999 to 99999.9999
U Starting point in 2nd axis Q226 (absolute):
Minimum-point coordinate of the surface to be
multipass-milled in the minor axis of the working N = Q240
Q219
Q209
U Starting point in 3rd axis Q227 (absolute): Height
in the spindle axis at which multipass-milling is carried
out. Input range -99999.9999 to 99999.9999
Q226
U First side length Q218 (incremental): Length of the
surface to be multipass-milled in the reference axis of
the working plane, referenced to the starting point in Q218 X
the 1st axis. Input range 0 to 99999.9999 Q225
U Second side length Q219 (incremental): Length of

the surface to be multipass-milled in the minor axis of
the working plane, referenced to the starting point in
the 2nd axis. Input range 0 to 99999.9999 Q206
U Number of cuts Q240: Number of passes to be made Z
over the width. Input range 0 to 99999
the tool while moving from setup clearance to the Q227
milling depth in mm/min. Input range: 0 to
99999.9999; alternatively FAUTO, FU, FZ.
U Stepover feed rate Q209: Traversing speed of the
tool in mm/min when moving to the next pass. If you X
are moving the tool transversely in the material, enter
Q209 to be smaller than Q207. If you are moving it Example: NC blocks
transversely in the open, Q209 may be greater than
Q207. Input range 0 to 99999.9999, alternatively 71 CYCL DEF 230 MULTIPASS MILLING
FAUTO, FU, FZ
Q225=+10 ;STARTING PNT 1ST AXIS
U Setup clearance Q200 (incremental): Distance Q226=+12 ;STARTING PNT 2ND AXIS
between tool tip and milling depth for positioning at
the start and end of the cycle. Input range 0 to Q227=+2.5 ;STARTING PNT 3RD AXIS
99999.9999, alternatively PREDEF Q218=150 ;FIRST SIDE LENGTH
Q219=75 ;SECOND SIDE LENGTH
Q240=25 ;NUMBER OF CUTS
Q209=200 ;STEPOVER FEED RATE

10.4 RULED SURFACE (Cycle 231, DIN/ISO: G231)
10.4 RULED SURFACE (Cycle 231,
DIN/ISO: G231)
Cycle run
1 From the current position, the TNC positions the tool in a linear 3-D
movement to the starting point 1.
2 The tool subsequently advances to the stopping point 2 at the feed Z
rate for milling.
3 From this point, the tool moves at rapid traverse FMAX by the tool 4
diameter in the positive tool axis direction, and then back to 3
starting point 1.
Y
4 At the starting point 1 the TNC moves the tool back to the last 1
traversed Z value.
5 Then the TNC moves the tool in all three axes from point 1 in the
direction of point 4 to the next line.
2 X
6 From this point, the tool moves to the stopping point on this pass.
The TNC calculates the end point from point 2 and a movement in
the direction of point 3.
7 Multipass milling is repeated until the programmed surface has
been completed.
8 At the end of the cycle, the tool is positioned above the highest
programmed point in the spindle axis, offset by the tool diameter. Z
3
Y
1

Cutting motion
The starting point, and therefore the milling direction, is selectable
because the TNC always moves from point 1 to point 2 and in the total Z
movement from point 1 / 2 to point 3 / 4. You can program point 1 at
any corner of the surface to be machined.
If you are using an end mill for the machining operation, you can 3
optimize the surface finish in the following ways:
A shaping cut (spindle axis coordinate of point 1 greater than 2
spindle-axis coordinate of point 2) for slightly inclined surfaces. Y
A drawing cut (spindle axis coordinate of point 1 smaller than 4
spindle-axis coordinate of point 2) for steep surfaces.
When milling twisted surfaces, program the main cutting direction 1
(from point 1 to point 2) parallel to the direction of the steeper
inclination.
X
If you are using a spherical cutter for the machining operation, you can
optimize the surface finish in the following way:
When milling twisted surfaces, program the main cutting direction
(from point 1 to point 2) perpendicular to the direction of the
steepest inclination.
From the current position, the TNC positions the tool in a

linear 3-D movement to the starting point 1. Pre-position
the tool in such a way that no collision between tool and
fixtures can occur.
The TNC moves the tool with radius compensation R0 to
the programmed positions.
If required, use a center-cut end mill (DIN 844).

Cycle parameters
U Starting point in 1st axis Q225 (absolute): Starting
point coordinate of the surface to be multipass-milled
in the reference axis of the working plane. Input range Z
-99999.9999 to 99999.9999
Starting point coordinate of the surface to be
4
multipass-milled in the minor axis of the working Q236
3
Q233
U Starting point in 3rd axis Q227 (absolute): Starting
Q227
1
point coordinate of the surface to be multipass-milled
in the tool axis. Input range -99999.9999 to 2
Q230
99999.9999
U 2nd point in 1st axis Q228 (absolute): End point X
coordinate of the surface to be multipass milled in Q228 Q231 Q234 Q225
the reference axis of the working plane. Input range
-99999.9999 to 99999.9999
U 2nd point in 2nd axis Q229 (absolute): End Y
point coordinate of the surface to be multipass
milled in the minor axis of the working plane.
Input range -99999.9999 to 99999.9999 Q235 4
3
U 2nd point in 3rd axis Q230 (absolute): End point Q232
coordinate of the surface to be multipass milled in the
spindle axis. Input range -99999.9999 to 99999.9999 N = Q240
U 3rd point in 1st axis Q231 (absolute): Coordinate

of point 3 in the reference axis of the working plane. 2
Input range -99999.9999 to 99999.9999 Q229
U 3rd point in 2nd axis Q232 (absolute): Coordinate Q226 1

of point 3 in the minor axis of the working plane. Input Q207
range -99999.9999 to 99999.9999
X
U 3rd point in 3rd axis Q233 (absolute): Coordinate
of point 3 in the spindle axis. Input range:
-99999.9999 to 99999.9999

Example: NC blocks
U 4th point in 1st axis Q234 (absolute): Coordinate
of point 4 in the reference axis of the working plane.
Input range -99999.9999 to 99999.9999 72 CYCL DEF 231 RULED SURFACE
U 4th point in 2nd axis Q235 (absolute): Coordinate Q225=+0 ;STARTING PNT 1ST AXIS
of point 4 in the minor axis of the working plane. Input Q226=+5 ;STARTING PNT 2ND AXIS
range -99999.9999 to 99999.9999
Q227=-2 ;STARTING PNT 3RD AXIS
U 4th point in 3rd axis Q236 (absolute): Coordinate
of point 4 in the spindle axis. Input range: Q228=+100 ;2ND POINT 1ST AXIS
-99999.9999 to 99999.9999 Q229=+15 ;2ND POINT 2ND AXIS
U Number of cuts Q240: Number of passes to be made Q230=+5 ;2ND POINT 3RD AXIS
between points 1 and 4, 2 and 3. Input range 0 to
Q231=+15 ;3RD POINT 1ST AXIS
99999
Q232=+125 ;3RD POINT 2ND AXIS
tool in mm/min while milling. The TNC performs the Q233=+25 ;3RD POINT 3RD AXIS
first step at half the programmed feed rate. Input Q234=+15 ;4TH POINT 1ST AXIS
Q235=+125 ;4TH POINT 2ND AXIS
Q236=+25 ;4TH POINT 3RD AXIS

10.5 FACE MILLING (Cycle 232, DIN/ISO: G232)
10.5 FACE MILLING (Cycle 232,
DIN/ISO: G232)
Cycle run
Cycle 232 is used to face mill a level surface in multiple infeeds while
taking the finishing allowance into account. Three machining
strategies are available:
Strategy Q389=0: Meander machining, stepover outside the
surface being machined
Strategy Q389=1: Meander machining, stepover within the surface
being machined
Strategy Q389=2: Line-by-line machining, retraction and stepover
at the positioning feed rate
1 From the current position, the TNC positions the tool at rapid
traverse FMAX to the starting position 1 using positioning logic: If
the current position in the spindle axis is greater than the 2nd
setup clearance, the TNC positions the tool first in the machining
plane and then in the spindle axis. Otherwise it first moves to the
2nd setup clearance and then in the machining plane. The starting
point in the machining plane is offset from the edge of the
workpiece by the tool radius and the safety clearance to the side.
2 The tool then moves in the spindle axis at the positioning feed rate
to the first plunging depth calculated by the control.
Strategy Q389=0
3 The tool then advances to the stopping point 2 at the feed rate for
milling. The end point lies outside the surface. The control Z
calculates the end point from the programmed starting point, the
programmed length, the programmed safety clearance to the side
and the tool radius.
2
the pre-positioning feed rate. The offset is calculated from the
programmed width, the tool radius and the maximum path overlap Y
factor.
5 The tool then moves back in the direction of the starting point 1.
1 X
6 The process is repeated until the programmed surface has been
completed. At the end of the last pass, the tool plunges to the next
machining depth.
7 In order to avoid non-productive motions, the surface is then
machined in reverse direction.
8 The process is repeated until all infeeds have been machined. In
the last infeed, simply the finishing allowance entered is milled at
the finishing feed rate.
9 At the end of the cycle, the TNC retracts the tool at FMAX to the

Strategy Q389=1
milling. The end point lies within the surface. The control Z
programmed length and the tool radius.
2
the pre-positioning feed rate. The offset is calculated from the Y
programmed width, the tool radius and the maximum path overlap
factor.
5 The tool then moves back in the direction of the starting point 1.
The motion to the next line occurs within the workpiece borders.
1 X
6 The process is repeated until the programmed surface has been
completed. At the end of the last pass, the tool plunges to the next
machining depth.
Strategy Q389=2
milling. The end point lies outside the surface. The control Z
programmed length, the programmed safety clearance to the side
and the tool radius.
4 The TNC positions the tool in the spindle axis to the setup
clearance over the current infeed depth, and then moves at the 2
pre-positioning feed rate directly back to the starting point in the Y
next line. The TNC calculates the offset from the programmed
width, the tool radius and the maximum path overlap factor.
5 The tool then returns to the current infeed depth and moves in the 1 X
direction of the next end point 2.
6 The milling process is repeated until the programmed surface has
been completed. At the end of the last pass, the tool plunges to
the next machining depth.
Enter the 2nd setup clearance in Q204 so that no collision

between tool and clamping devices can occur.

Cycle parameters
U Machining strategy (0/1/2) Q389: Specify how the
TNC is to machine the surface: Y
0: Meander machining, stepover at positioning feed
rate outside the surface to be machined
1: Meander machining, stepover at feed rate for
milling within the surface to be machined
2: Line-by-line machining, retraction and stepover at
the positioning feed rate
Q219
U Starting point in 1st axis Q225 (absolute):
Starting point coordinate of the surface to be
machined in the reference axis of the working Q226
Starting point coordinate of the surface to be Q218 X
multipass-milled in the minor axis of the working Q225
U Starting point in 3rd axis Q227 (absolute):
Coordinate of the workpiece surface used to calculate
the infeeds. Input range -99999.9999 to 99999.9999
U End point in 3rd axis Q386 (absolute): Coordinate Z
in the spindle axis to which the surface is to be face
milled. Input range -99999.9999 to 99999.9999
U First side length Q218 (incremental value): Length Q227
of the surface to be machined in the reference axis of
the working plane. Use the algebraic sign to specify
the direction of the first milling path in reference to Q386
the starting point in the 1st axis. Input range:
-99999.9999 to 99999.9999
U Second side length Q219 (incremental value):
Length of the surface to be machined in the minor
X
axis of the working plane. Use the algebraic sign to
specify the direction of the first stepover in
reference to the starting point in the 2nd axis.
Input range -99999.9999 to 99999.9999

U Maximum plunging depth Q202 (incremental value):
Maximum amount that the tool is advanced each
time. The TNC calculates the actual plunging depth
from the difference between the end point and
starting point of the tool axis (taking the finishing Z
allowance into account), so that uniform plunging
depths are used each time. Input range 0 to Q204
99999.9999 Q200
U Allowance for floor Q369 (incremental): Distance Q202
used for the last infeed. Input range 0 to 99999.9999
Q369
U Max. path overlap factor Q370: Maximum stepover
factor k. The TNC calculates the actual stepover from
the second side length (Q219) and the tool radius so
that a constant stepover is used for machining. If you
have entered a radius R2 in the tool table (e.g. tooth X
radius when using a face-milling cutter), the TNC
reduces the stepover accordingly. Input range 0.1 to
Y
tool during milling in mm/min. Input range: 0 to Q207
U Feed rate for finishing Q385: Traversing speed of k
the tool in mm/min, while milling the last infeed. Input
speed of the tool in mm/min when approaching the
starting position and when moving to the next pass.
If you are moving the tool transversely to the material Q253
(Q389=1), the TNC moves the tool at the feed rate for
milling Q207. Input range 0 to 99999.9999, X
alternatively FMAX, FAUTO, PREDEF. Q357

Example: NC blocks

between tool tip and the starting position in the tool
axis. If you are milling with machining strategy 71 CYCL DEF 232 FACE MILLING
Q389=2, the TNC moves the tool at the setup Q389=2 ;STRATEGY
clearance over the current plunging depth to the
starting point of the next pass. Input range 0 to Q225=+10 ;STARTING PNT 1ST AXIS
99999.9999, alternatively PREDEF Q226=+12 ;STARTING PNT 2ND AXIS
U Clearance to side Q357 (incremental): Safety Q227=+2.5 ;STARTING PNT 3RD AXIS
clearance to the side of the workpiece when the tool
approaches the first plunging depth, and distance at Q386=-3 ;END POINT IN 3RD AXIS
which the stepover occurs if the machining strategy Q218=150 ;FIRST SIDE LENGTH
Q389=0 or Q389=2 is used. Input range 0 to
99999.9999 Q219=75 ;SECOND SIDE LENGTH
U 2nd setup clearance Q204 (incremental): Coordinate Q202=2 ;MAX. PLUNGING DEPTH
in the spindle axis at which no collision between tool Q369=0.5 ;ALLOWANCE FOR FLOOR
99999.9999, alternatively PREDEF Q370=1 ;MAX. OVERLAP
Q357=2 ;CLEARANCE TO SIDE

Example: Multipass milling
Y Y
100
X Z
100 35
0 BEGIN PGM C230 MM

1 BLK FORM 0.1 Z X+0 Y+0 Z+0 Definition of workpiece blank
2 BLK FORM 0.2 X+100 Y+100 Z+40
6 CYCL DEF 230 MULTIPASS MILLING Cycle definition: MULTIPASS MILLING
Q225=+0 ;STARTNG PNT 1ST AXIS
Q226=+0 ;STARTNG PNT 2ND AXIS
Q227=+35 ;STARTNG PNT 3RD AXIS
Q219=100 ;2ND SIDE LENGTH
Q209=150 ;STEPOVER FEED RATE

7 L X+-25 Y+0 R0 FMAX M3 Pre-position near the starting point
8 CYCL CALL Cycle call
10 END PGM C230 MM


Cycles: Coordinate
Transformations
11.1 Fundamentals
11.1 Fundamentals
Overview
Once a contour has been programmed, you can position it on the
workpiece at various locations and in different sizes through the use
of coordinate transformations. The TNC provides the following
coordinate transformation cycles:
Cycle Soft key Page

7 DATUM SHIFT Page 274
For shifting contours directly within the
program or from datum tables
247 DATUM SETTING Page 281

Datum setting during program run
8 MIRROR IMAGE Page 282

Mirroring contours
10 ROTATION Page 284

For rotating contours in the working
plane
11 SCALING FACTOR Page 286

For increasing or reducing the size of
contours
26 AXIS-SPECIFIC SCALING FACTOR Page 288

For increasing or reducing the size of
contours with scaling factors for each
axis
19 WORKING PLANE Page 290

Machining in tilted coordinate system on
machines with swivel heads and/or
rotary tables
272 Cycles: Coordinate Transformations

11.1 Fundamentals
Effect of coordinate transformations
Beginning of effect: A coordinate transformation becomes effective as
soon as it is defined—it is not called. It remains in effect until it is
changed or canceled.
To cancel coordinate transformations:
Define cycles for basic behavior with a new value, such as scaling
factor 1.0
Execute a miscellaneous function M2, M30, or an END PGM block
(depending on MP7300).
Select a new program
Program miscellaneous function M142 "Erasing modal program
information".

11.2 DATUM SHIFT (Cycle 7, DIN/ISO: G54)
11.2 DATUM SHIFT (Cycle 7,
DIN/ISO: G54)
Effect
A DATUM SHIFT allows machining operations to be repeated at
various locations on the workpiece. Z
When the DATUM SHIFT cycle is defined, all coordinate data is based Z
Y Y
on the new datum. The TNC displays the datum shift in each axis in X
the additional status display. Input of rotary axes is also permitted.
Reset
Program a datum shift to the coordinates X=0, Y=0 etc. directly with
X
a cycle definition.
Use the TRANS DATUM RESET function.
Call a datum shift to the coordinates
X=0; Y=0 etc. from the datum table.
Graphics
If you program a new BLK FORM after a datum shift, you can use
MP 7310 to determine whether the BLK FORM is referenced to the
current datum or to the original datum. Referencing a new BLK FORM
to the current datum enables you to display each part in a program in
which several pallets are machined.
Z
Y
Y X
Cycle parameters
U Datum shift: Enter the coordinates of the new datum. Example: NC blocks
Absolute values are referenced to the manually set
workpiece datum. Incremental values are always 13 CYCL DEF 7.0 DATUM SHIFT
referenced to the datum which was last valid—this 14 CYCL DEF 7.1 X+60
can be a datum which has already been shifted. Input
range: Up to 6 NC axes, each from –99999.9999 to 16 CYCL DEF 7.3 Z-5
99999.9999 15 CYCL DEF 7.2 Y+40

11.3 DATUM Shift with Datum Tables (Cycle 7, DIN/ISO: G53)
11.3 DATUM Shift with Datum
Tables (Cycle 7, DIN/ISO: G53)
Effect
Datum tables are used for:
Frequently recurring machining sequences at various locations on
the workpiece
Z
Frequent use of the same datum shift
Y
Within a program, you can either program datum points directly in the N5
cycle definition or call them from a datum table. N4
N3
Reset N2 X
Call a datum shift to the coordinates N1
X=0; Y=0 etc. from the datum table. N0
Execute a datum shift to the coordinates X=0, Y=0 etc. directly with
a cycle definition:
Use the TRANS DATUM RESET function.
Graphics
If you program a new BLK FORM after a datum shift, you can use
MP 7310 to determine whether the BLK FORM is referenced to the
current datum or to the original datum. Referencing a new BLK FORM
to the current datum enables you to display each part in a program in
which several pallets are machined. Z
Y
Status displays N2
In the additional status display, the following data from the datum
table are shown: N1
Y2 X
Name and path of the active datum table
Active datum number Y1 N0
Comment from the DOC column of the active datum number X2
X1

Datums from a datum table are always and exclusively
referenced to the current datum (preset).
MP7475, which earlier defined whether datums are
referenced to the machine datum or the workpiece datum,
now serves only as a safety measure. If MP7475 = 1, the
TNC outputs an error message if a datum shift is called
from a datum table.
Datum tables from the TNC 4xx whose coordinates are
referenced to the machine datum (MP7475 = 1) cannot be
used in the iTNC 530.
If you are using datum shifts with datum tables, then use
the SEL TABLE function to activate the desired datum table
from the NC program.
If you work without SEL TABLE, then you must activate the
desired datum table before the test run or the program
run. (This applies also to the programming graphics).
Use the file management to select the desired table for
a test run in the Test Run operating mode: The table
receives the status S.
Use the file management in a program run mode to
select the desired table for a program run: The table
receives the status M.
The coordinate values from datum tables are only effective
with absolute coordinate values.
New lines can only be inserted at the end of the table.

Cycle parameters
U Datum shift: Enter the number of the datum from the Example: NC blocks
datum table or a Q parameter. If you enter a Q
parameter, the TNC activates the datum number 77 CYCL DEF 7.0 DATUM SHIFT
entered in the Q parameter. Input range: 0 to 9999 78 CYCL DEF 7.1 #5
Selecting a datum table in the part program

With the SEL TABLE function you select the table from which the TNC
takes the datums:
U To select the functions for program call, press the
PGM CALL key.
U Press the DATUM TABLE soft key.

U Select a dati, table with the arrow keys or by mouse
click and confirm by pressing ENT: The TNC enters
the complete path name in the SEL TABLE block.
Alternatively you can also enter the table name or the complete path
name of the table to be called directly via the keyboard.
Program a SEL TABLE block before Cycle 7 Datum Shift.

A datum table selected with SEL TABLE remains active until
you select another datum table with SEL TABLE or through
PGM MGT.
You can define datum tables and datum numbers in an NC
block with the TRANS DATUM TABLE function.

Editing the datum table in the Programming and
Editing mode of operation
After you have changed a value in a datum table, you must

save the change with the ENT key. Otherwise the change
might not be included during program run.
Select the datum table in the Programming and Editing mode of

operation.
U Press the PGM MGT key to call the file manager.
U Display the datum tables: Press the soft keys SELECT
TYPE and SHOW .D.
U Select the desired table or enter a new file name.
U Edit the file. The soft-key row comprises the following
functions for editing:
Function Soft key

Select beginning of table
Select end of table
Go to previous page
Go to next page
Insert line (only possible at end of table)
Delete line
Confirm the entered line and go to the beginning of

the next line
Add the entered number of lines (datums) to the end

of the table

Editing a pocket table in a Program Run
operating mode
In a program run mode you can select the active datum table. Press
the DATUM TABLE soft key. You can then use the same editing
functions as in the Programming and Editing mode of operation.
Transferring the actual values into the datum

table
You can enter the current tool position or the last probed position in
the datum table by pressing the “actual-position-capture” key:
U Place the text box on the line of the column in which you want to
enter the position.
U Select the actual-position-capture function: The TNC
opens a pop-up window that asks whether you want
to enter the current tool position or the last probed
values.
U Select the desired function with the arrow keys and
confirm your selection with the ENT key.
U To enter the values in all axes, press the ALL VALUES
soft key.
U To enter the value in the axis where the text box is
located, press the CURRENT VALUE soft key.

Configuring the datum table
In the second and third soft-key rows you can define for each datum
table the axes for which you wish to set the datums. In the standard
setting all of the axes are active. If you wish to exclude an axis, set the
corresponding soft key to OFF. The TNC then deletes that column
from the datum table.
If you do not wish to define a datum table for an active axis, press the
NO ENT key. The TNC then enters a dash in that column.
To exit a datum table

Select a different type of file in file management and choose the
desired file.

11.4 DATUM SETTING (Cycle 247, DIN/ISO: G247)
11.4 DATUM SETTING (Cycle 247,
DIN/ISO: G247)
Effect
With the Cycle DATUM SETTING, you can activate as the new datum
a preset defined in a preset table. Z
After a DATUM SETTING cycle definition, all of the coordinate inputs Z
Y Y
and datum shifts (absolute and incremental) are referenced to the new X
preset.
Status display
In the status display the TNC shows the active preset number behind
X
the datum symbol.
Please note before programming:
When activating a datum from the preset table, the TNC

resets the active datum shift.
The TNC sets the preset only in the axes that are defined
with values in the preset table. The datums of axes
marked with — remain unchanged.
If you activate preset number 0 (line 0), then you activate
the datum that you last set in a manual operating mode.
Cycle 247 is not functional in Test Run mode.
Cycle parameters
U Number for datum?: Enter the number of the datum to Example: NC blocks
be activated from the preset table. Input range: 0 to
65535 13 CYCL DEF 247 DATUM SETTING
Q339=4 ;DATUM NUMBER

11.5 MIRROR IMAGE (Cycle 8, DIN/ISO: G28)
11.5 MIRROR IMAGE (Cycle 8,
DIN/ISO: G28)
Effect
The TNC can machine the mirror image of a contour in the working
plane. Z
Y
The mirror image cycle becomes effective as soon as it is defined in
the program. It is also effective in the Positioning with MDI mode of
operation. The active mirrored axes are shown in the additional status
display.
X
If you mirror only one axis, the machining direction is reversed.
(Except in fixed cycles).
If you mirror two axes, the machining direction remains the same.
The result of the mirror image depends on the location of the datum:
If the datum lies on the contour to be mirrored, the element simply
flips over.
If the datum lies outside the contour to be mirrored, the element
also “jumps” to another location.
Reset
Program the MIRROR IMAGE cycle once again with NO ENT.
Z
If you mirror only one axis, the machining direction is

reversed for the milling cycles (Cycles 2xx). Exception:
Cycle 208, in which the direction defined in the cycle
applies.

11.5 MIRROR IMAGE (Cycle 8, DIN/ISO: G28)
Cycle parameters
U Mirrored axis?: Enter the axis to be mirrored. You Example: NC blocks
can mirror all axes except for the spindle axis—
including rotary axes—with the exception of the 79 CYCL DEF 8.0 MIRROR IMAGE
spindle axis and its associated auxiliary axis. You can 80 CYCL DEF 8.1 X Y U
enter up to three axes. Input range: Up to three NC
axes X, Y, Z, U, V, W, A, B, C

11.6 ROTATION (Cycle 10, DIN/ISO: G73)
11.6 ROTATION (Cycle 10, DIN/ISO:
G73)
Effect
The TNC can rotate the coordinate system about the active datum in
the working plane within a program. Z
The ROTATION cycle becomes effective as soon as it is defined in the
program. It is also effective in the Positioning with MDI mode of Y Z
operation. The active rotation angle is shown in the additional status Y X
display.
Reference axis for the rotation angle: X
X/Y plane X axis
Y/Z plane Y axis
Z/X plane Z axis
Reset
Program the ROTATION cycle once again with a rotation angle of 0°.
Y
Y
X
35°
40
X
60
An active radius compensation is canceled by defining

Cycle 10 and must therefore be reprogrammed, if
necessary.
After defining Cycle 10, you must move both axes of the
working plane to activate rotation for all axes.

11.6 ROTATION (Cycle 10, DIN/ISO: G73)
Cycle parameters
U Rotation: Enter the rotation angle in degrees (°). Input Example: NC blocks
range –360.000° to +360.000° (absolute or
incremental) 12 CALL LBL 1
13 CYCL DEF 7.0 DATUM SHIFT
14 CYCL DEF 7.1 X+60
15 CYCL DEF 7.2 Y+40
16 CYCL DEF 10.0 ROTATION
17 CYCL DEF 10.1 ROT+35
18 CALL LBL 1

11.7 SCALING (Cycle 11, DIN/ISO: G72)
11.7 SCALING (Cycle 11, DIN/ISO:
G72)
Effect
The TNC can increase or reduce the size of contours within a program,
enabling you to program shrinkage and oversize allowances. Z
The SCALING FACTOR becomes effective as soon as it is defined in
the program. It is also effective in the Positioning with MDI mode of Y Z
Y
operation. The active scaling factor is shown in the additional status X
display.
The scaling factor has an effect on X
The working plane, or on all three coordinate axes at the same time
(depending on MP 7410)
Dimensions in cycles
The parallel axes U,V,W
Prerequisite
It is advisable to set the datum to an edge or a corner of the contour
before enlarging or reducing the contour.
Enlargement: SCL greater than 1 and up to 99.999 999
Reduction: SCL less than 1 and at least 0.000 001 Y
Y
Reset
Program the SCALING FACTOR cycle once again with a scaling factor
of 1. (22.5)
40
30 X
(27)
X
36 60

11.7 SCALING (Cycle 11, DIN/ISO: G72)
Cycle parameters
U Scaling factor?: Enter the scaling factor SCL. The Example: NC blocks
TNC multiplies the coordinates and radii by the SCL
factor (as described under “Effect” above). Input 11 CALL LBL 1
range: 0.000000 to 99.999999 12 CYCL DEF 7.0 DATUM SHIFT
13 CYCL DEF 7.1 X+60
14 CYCL DEF 7.2 Y+40
15 CYCL DEF 11.0 SCALING
16 CYCL DEF 11.1 SCL 0.75
17 CALL LBL 1

11.8 AXIS-SPECIFIC SCALING (Cycle 26)
11.8 AXIS-SPECIFIC SCALING
(Cycle 26)
Effect
With Cycle 26 you can account for shrinkage and oversize factors for
each axis.
The SCALING FACTOR becomes effective as soon as it is defined in Y
the program. It is also effective in the Positioning with MDI mode of
operation. The active scaling factor is shown in the additional status
display.
Reset CC
Program the SCALING FACTOR cycle once again with a scaling factor
of 1 for the same axis.
Coordinate axes sharing coordinates for arcs must be

enlarged or reduced by the same factor.
You can program each coordinate axis with its own axis-
specific scaling factor.
In addition, you can enter the coordinates of a center for all
scaling factors.
The size of the contour is enlarged or reduced with
reference to the center, and not necessarily (as in Cycle 11
SCALING) with reference to the active datum.

11.8 AXIS-SPECIFIC SCALING (Cycle 26)
Cycle parameters
U Axis and scaling factor: Select the coordinate
axis/axes by soft key and enter the factor(s) involved Y
in enlarging or reducing. Input range: 0.000000 to
99.999999
U Center coordinates: Enter the center of the axis-
specific enlargement or reduction. Input range: 20 CC
-99999.9999 to 99999.9999
X
15
Example: NC blocks
25 CALL LBL 1
26 CYCL DEF 26.0 AXIS-SPECIFIC SCALING
27 CYCL DEF 26.1 X 1.4 Y 0.6 CCX+15 CCY+20
28 CALL LBL 1

11.9 WORKING PLANE (Cycle 19, DIN/ISO: G80, Software Option 1)
11.9 WORKING PLANE (Cycle 19,
Option 1)
Effect
In Cycle 19 you define the position of the working plane—i.e. the
position of the tool axis referenced to the machine coordinate B
system—by entering tilt angles. There are two ways to determine the
position of the working plane:
Enter the position of the rotary axes directly. Z
Describe the position of the working plane using up to 3 rotations
(spatial angle) of the fixed machine coordinate system. The
required spatial angle can be calculated by cutting a perpendicular
line through the tilted working plane and considering it from the axis
around which you wish to tilt. With two spatial angles, every tool
position in space can be defined exactly.
Note that the position of the tilted coordinate system, and

therefore also all movements in the tilted system, are
dependent on your description of the tilted plane.
X
If you program the position of the working plane via spatial angles, the
TNC will calculate the required angle positions of the tilted axes
automatically and will store these in the parameters Q120 (A axis) to
Q122 (C axis). Z
Warning! Y
Depending on your machine configuration, two
mathematical solutions (axis positions) are possible for a
spatial angle definition. Conduct appropriate tests on your Y'
machine to find out which axis position the TNC software
selects in each case.
If the DCM software option is available to you, the axis
position can be displayed in the PROGRAM +
KINEMATICS view during test run (see User’s Manual for
Conversational Programming, Dynamic Collision X
Monitioring). X'

The axes are always rotated in the same sequence for calculating the
tilt of the plane: The TNC first rotates the A axis, then the B axis, and
finally the C axis.
Cycle 19 becomes effective as soon as it is defined in the program. As
soon as you move an axis in the tilted system, the compensation for
this specific axis is activated. You must move all axes to activate
compensation for all axes.
If you set the function Tilting program run to Active in the Manual
Operation mode, the angular value entered in this menu is overwritten
by Cycle 19 WORKING PLANE.
The functions for tilting the working plane are interfaced to

the TNC and the machine tool by the machine tool builder.
With some swivel heads and tilting tables, the machine
tool builder determines whether the entered angles are
interpreted as coordinates of the rotary axes or as
mathematical angles of a tilted plane. Refer to your
machine tool manual.
Because nonprogrammed rotary axis values are

interpreted as unchanged, you should always define all
three spatial angles, even if one or more angles are at zero.
The working plane is always tilted around the active
datum.
If you use Cycle 19 when M120 is active, the TNC
automatically rescinds the radius compensation, which
also rescinds the M120 function.
Ensure that the last defined angle is smaller than 360°.

Cycle parameters
U Rotary axis and tilt angle?: Enter the axes of
rotation together with the associated tilt angles. The
rotary axes A, B and C are programmed using soft
keys. Input range: -360.000 to 360.000
If the TNC automatically positions the rotary axes, you can enter the
following parameters:
U Feed rate? F=: Traverse speed of the rotary axis
during automatic positioning. Input range: 0 to S Y Z
99999.999
X
U Setup clearance? (incremental value): The TNC
positions the tilting head so that the position that B
results from the extension of the tool by the set-up X
clearance does not change relative to the workpiece. C
Input range: 0 to 99999.9999 S S-S
Please note that the setup clearance in Cycle 19 does not
refer to the upper edge of the workpiece (as is the case in
the fixed cycles) but rather to the active datum.
Resetting
To cancel the tilt angle, redefine the WORKING PLANE cycle and enter
an angular value of 0° for all axes of rotation. You must then program
the WORKING PLANE cycle once again by answering the dialog
question with the NO ENT key to disable the function.

Positioning the axes of rotation
The machine tool builder determines whether Cycle 19

positions the axes of rotation automatically or whether
they must be positioned manually in the program. Refer to
Manual positioning of rotary axes

If the rotary axes are not positioned automatically in Cycle 19, you
must position them in a separate L block after the cycle definition.
If you use axis angles, you can define the axis values right in the L
block. If you use spatial angles, then use the Q parameters Q120 (A-
axis value), Q121 (B-axis value) and Q122 (C-axis value), which are
described by Cycle 19.
Example NC blocks:
10 L Z+100 R0 FMAX
11 L X+25 Y+10 R0 FMAX
12 CYCL DEF 19.0 WORKING PLANE Define the spatial angle for calculation of the
compensation
13 CYCL DEF 19.1 A+0 B+45 C+0
14 L A+Q120 C+Q122 R0 F1000 Position the rotary axes by using values calculated
by Cycle 19
15 L Z+80 R0 FMAX Activate compensation for the spindle axis
16 L X-8.5 Y-10 R0 FMAX Activate compensation for the working plane
For manual positioning, always use the rotary axis

positions stored in Q parameters Q120 to Q122.
Avoid using functions, such as M94 (modulo rotary axes),
in order to avoid discrepancies between the actual and
nominal positions of rotary axes in multiple definitions.

Automatic positioning of rotary axes
If the rotary axes are positioned automatically in Cycle 19:
The TNC can position only controlled axes
In order for the tilted axes to be positioned, you must enter a feed
rate and a setup clearance in addition to the tilting angles, during
cycle definition.
Use only preset tools (the full tool length must be defined).
The position of the tool tip as referenced to the workpiece surface
remains nearly unchanged after tilting.
The TNC performs the tilt at the last programmed feed rate. The
maximum feed rate that can be reached depends on the complexity
of the swivel head or tilting table.
Example NC blocks:
10 L Z+100 R0 FMAX
11 L X+25 Y+10 R0 FMAX
12 CYCL DEF 19.0 WORKING PLANE Define the angle for calculation of the compensation
13 CYCL DEF 19.1 A+0 B+45 C+0 F5000 SETUP50 Also define the feed rate and the clearance
14 L Z+80 R0 FMAX Activate compensation for the spindle axis
15 L X-8.5 Y-10 R0 FMAX Activate compensation for the working plane

Position display in the tilted system
On activation of Cycle 19, the displayed positions (ACTL and NOML) and
the datum indicated in the additional status display are referenced to
the tilted coordinate system. The positions displayed immediately
after cycle definition might not be the same as the coordinates of the
last programmed position before Cycle 19.
Workspace monitoring
The TNC monitors only those axes in the tilted coordinate system that
are moved. If necessary, the TNC outputs an error message.
Positioning in a tilted coordinate system

With the miscellaneous function M130 you can move the tool, while
the coordinate system is tilted, to positions that are referenced to the
non-tilted coordinate system.
Positioning movements with straight lines that are referenced to the
machine coordinate system (blocks with M91 or M92) can also be
executed in a tilted working plane. Constraints:
Positioning is without length compensation.
Positioning is without machine geometry compensation.
Tool radius compensation is not permitted.

Combining coordinate transformation cycles
When combining coordinate transformation cycles, always make sure
the working plane is swiveled around the active datum. You can
program a datum shift before activating Cycle 19. In this case, you are
shifting the machine-based coordinate system.
If you program a datum shift after having activated Cycle 19, you are
shifting the tilted coordinate system.
Important: When resetting the cycles, use the reverse sequence used
for defining them:
1st: Activate the datum shift
2nd: Activate tilting function
3rd: Activate rotation
...
Machining
...
1st: Reset the rotation
2nd: Reset the tilting function
3rd: Reset the datum shift
Automatic workpiece measurement in the tilted

system
The TNC measuring cycles enable you to have the TNC measure a
workpiece in a tilted system automatically. The TNC stores the
measured data in Q parameters for further processing (for example,
for printout).

Procedure for working with Cycle 19 WORKING
PLANE
1 Write the program
U Define the tool (not required if TOOL.T is active), and enter the full
tool length.
U Call the tool
U Retract the tool in the tool axis to a position where there is no
danger of collision with the workpiece (clamping devices) during
tilting.
U If required, position the rotary axis or axes with an L block to the
appropriate angular value(s) (depending on a machine parameter).
U Activate datum shift if required.
U Define Cycle 19 WORKING PLANE; enter the angular values for the
tilt axes.
U Traverse all principal axes (X, Y, Z) to activate compensation.
U Write the program as if the machining process were to be executed
in a non-tilted plane.
U If required, define Cycle 19 WORKING PLANE with other angular
values to execute machining in a different axis position. In this case,
it is not necessary to reset Cycle 19. You can define the new angular
values directly.
U Reset Cycle 19 WORKING PLANE; program 0° for all rotary axes.
U Disable the WORKING PLANE function; redefine Cycle 19 and
answer the dialog question with NO ENT.
U Reset datum shift if required.
U Position the rotary axes to the 0° position, if required.
2 Clamp the workpiece
3 Preparations in the operating mode
Positioning with Manual Data Input (MDI)
Pre-position the rotary axis/axes to the corresponding angular value(s)
for setting the datum. The angular value depends on the selected
reference plane on the workpiece.

4 Preparations in the operating mode
Manual Operation
Use the 3D-ROT soft key to set the function TILT WORKING PLANE
to ACTIVE in the Manual Operating mode. For open loop axes, enter
the angular values for the rotary axes into the menu.
If the axes are not controlled, the angular values entered in the menu
must correspond to the actual position(s) of the rotary axis or axes,
respectively. The TNC will otherwise calculate a wrong datum.
5 Datum setting
Manually by touching the workpiece with the tool in the untilted
coordinate system.
Controlled with a HEIDENHAIN 3-D touch probe (see the Touch
Probe Cycles User's Manual, chapter 2).
Automatically with a HEIDENHAIN 3-D touch probe (see the Touch
Probe Cycles User's Manual, chapter 3).
6 Start the part program in the operating mode Program Run, Full
Sequence
7 Manual Operation mode
Use the 3-D ROT soft key to set the TILT WORKING PLANE function
to INACTIVE. Enter an angular value of 0° for each rotary axis in the
menu.

Example: Coordinate transformation cycles
Program sequence
Program the coordinate transformations in R5
10
the main program Y R5
Machining within a subprogram X
10
130
20 10
45°
30
65
X
65 130
0 BEGIN PGM COTRANS MM

2 BLK FORM 0.2 X+130 Y+130 Z+0
6 CYCL DEF 7.0 DATUM SHIFT Shift datum to center
7 CYCL DEF 7.1 X+65
8 CYCL DEF 7.2 Y+65
9 CALL LBL 1 Call milling operation
10 LBL 10 Set label for program section repeat
11 CYCL DEF 10.0 ROTATION Rotate by 45° (incremental)
12 CYCL DEF 10.1 IROT+45
13 CALL LBL 1 Call milling operation
14 CALL LBL 10 REP 6/6 Return jump to LBL 10; repeat the milling operation six times
15 CYCL DEF 10.0 ROTATION Reset the rotation
16 CYCL DEF 10.1 ROT+0
17 TRANS DATUM RESET Reset the datum shift

19 LBL 1 Subprogram 1
20 L X+0 Y+0 R0 FMAX Define milling operation
21 L Z+2 R0 FMAX M3
22 L Z-5 R0 F200
23 L X+30 RL
24 L IY+10
25 RND R5
26 L IX+20
27 L IX+10 IY-10
28 RND R5
29 L IX-10 IY-10
30 L IX-20
31 L IY+10
32 L X+0 Y+0 R0 F5000
33 L Z+20 R0 FMAX
34 LBL 0
35 END PGM COTRANS MM

Cycles: Special
Functions
12.1 Fundamentals
12.1 Fundamentals
Overview
The TNC provides four cycles for the following special purposes:
Cycle Soft key Page

9 DWELL TIME Page 303
12 PROGRAM CALL Page 304
13 ORIENTED SPINDLE STOP Page 306
32 TOLERANCE Page 307
302 Cycles: Special Functions

12.2 DWELL TIME (Cycle 9,
12.2 DWELL TIME (Cycle 9, DIN/ISO: G04)

DIN/ISO: G04)
Function
This causes the execution of the next block within a running program
to be delayed by the programmed DWELL TIME. A dwell time can be
used for such purposes as chip breaking.
The cycle becomes effective as soon as it is defined in the program.
Modal conditions such as spindle rotation are not affected.
Example: NC blocks
89 CYCL DEF 9.0 DWELL TIME

90 CYCL DEF 9.1 DWELL 1.5
Cycle parameters
U Dwell time in seconds: Enter the dwell time in
seconds. Input range: 0 to 3600 s (1 hour) in steps of
0.001 seconds

12.3 PROGRAM CALL (Cycle 12, DIN/ISO: G39)
12.3 PROGRAM CALL (Cycle 12,
DIN/ISO: G39)
Cycle function
Routines that you have programmed (such as special drilling cycles or
geometrical modules) can be written as main programs and then
called like fixed cycles.
7 CYCL DEF 12.0 0 BEGIN PGM

PGM CALL LOT31 MM
8 CYCL DEF 12.1
LOT31
9 ... M99
END PGM
The program you are calling must be stored on the hard

disk of your TNC.
If the program you are defining to be a cycle is located in
the same directory as the program you are calling it from,
you need only to enter the program name.
If the program you are defining to be a cycle is not located
in the same directory as the program you are calling it
from, you must enter the complete path, for example
TNC:\KLAR35\FK1\50.H.
If you want to define a DIN/ISO program to be a cycle,
enter the file type .I behind the program name.
As a rule, Q parameters are globally effective when called
with Cycle 12. So please note that changes to Q
parameters in the called program can also influence the
calling program.

12.3 PROGRAM CALL (Cycle 12, DIN/ISO: G39)
Cycle parameters
U Program name: Enter the name of the program you Example: Designate program 50 as a cycle and call
want to call and, if necessary, the directory it is it with M99
located in. A maximum of 254 characters can be
entered. 55 CYCL DEF 12.0 PGM CALL
The following functions can be used to call the defined program: 56 CYCL DEF 12.1 PGM TNC:\KLAR35\FK1\50.H
CYCL CALL (separate block), or 57 L X+20 Y+50 FMAX M99

CYCL CALL POS (separate block) or
M99 (blockwise) or
M89 (executed after every positioning block)

12.4 ORIENTED SPINDLE STOP (Cycle 13, DIN/ISO: G36)
12.4 ORIENTED SPINDLE STOP
Cycle function
Machine and TNC must be specially prepared by the Z

Y
The TNC can control the machine tool spindle and rotate it to a given
angular position. X
Oriented spindle stops are required for
Tool changing systems with a defined tool change position
Orientation of the transmitter/receiver window of HEIDENHAIN 3-D
touch probes with infrared transmission
The angle of orientation defined in the cycle is positioned to by
entering M19 or M20 (depending on the machine).
If you program M19 or M20 without having defined Cycle 13, the TNC
positions the machine tool spindle to an angle that has been set by the
machine manufacturer (see your machine manual). Example: NC blocks
93 CYCL DEF 13.0 ORIENTATION

94 CYCL DEF 13.1 ANGLE 180
Cycle 13 is used internally for machining cycles 202, 204

and 209. Please note that, if required, you must program
Cycle 13 again in your NC program after one of the
machining cycles mentioned above.
Cycle parameters
U Angle of orientation: Enter the angle referenced to
the reference axis of the working plane. Input range:
0.0000° to 360.0000°

12.5 TOLERANCE (Cycle 32, DIN/ISO: G62)
12.5 TOLERANCE (Cycle 32, DIN/ISO:
G62)
Cycle function

machine tool builder for use of this cycle. The cycle may
be locked.
T
With the entries in Cycle 32 you can influence the result of HSC Z
machining with respect to accuracy, surface definition and speed,
inasmuch as the TNC has been adapted to the machine’s
characteristics.
The TNC automatically smoothens the contour between two path
elements (whether compensated or not). The tool has constant
contact with the workpiece surface and therefore reduces wear on the
machine tool. The tolerance defined in the cycle also affects the X
traverse paths on circular arcs.
If necessary, the TNC automatically reduces the programmed feed
rate so that the program can be machined at the fastest possible
speed without short pauses for computing time. Even if the TNC
does not move with reduced speed, it will always comply with
the tolerance that you have defined. The larger you define the
tolerance, the faster the TNC can move the axes.
Smoothing the contour results in a certain amount of deviation from
the contour. The size of this contour error (tolerance value) is set in
a machine parameter by the machine manufacturer. You can change
the pre-set tolerance value with Cycle 32.

Influences of the geometry definition in the CAM
system
The most important factor of influence in offline NC program creation
is the chord error S defined in the CAM system. The maximum point
CAM PP TNC
spacing of NC programs generated in a postprocessor (PP) is defined
through the chord error. If the chord error is less than or equal to the S
tolerance value T defined in Cycle 32, then the TNC can smooth the
T
contour points unless any special machine settings limit the
programmed feed rate.
You will achieve optimal smoothing if in Cycle 32 you choose a
tolerance value between 110% and 200% of the CAM chord error.
Z

With very small tolerance values the machine cannot cut

the contour without jerking. These jerking movements are
not caused by poor processing power in the TNC, but by
the fact that, in order to machine the contour element
transitions very exactly, the TNC might have to drastically
reduce the speed.
Cycle 32 is DEF active which means that it becomes
The TNC resets Cycle 32 if you
Redefine it and confirm the dialog question for the
tolerance value with NO ENT
Select a new program with the PGM MGT key.
After you have reset Cycle 32, the TNC reactivates the
tolerance that was predefined by machine parameter.
In a program with millimeters set as unit of measure, the
TNC interprets the entered tolerance value in millimeters.
In an inch program it interprets it as inches.
If you transfer a program with Cycle 32 that contains only
the cycle parameter Tolerance value T, the control inserts
the two remaining parameters with the value 0 if required.
As the tolerance value increases, the diameter of circular
movements usually decreases. If the HSC filter is active
on your machine (ask your machine manufacturer, if
necessary), the circle can also become larger.
If Cycle 32 is active, the TNC shows the parameters
defined for Cycle 32 on the CYC tab of the additional status
display.

Cycle parameters
U Tolerance value T: Permissible contour deviation in Example: NC blocks
mm (or inches with inch programming). Input range
0 to 99999.9999 95 CYCL DEF 32.0 TOLERANCE
U HSC MODE, Finishing=0, Roughing=1: Activate filter: 96 CYCL DEF 32.1 T0.05
Input value 0: 97 CYCL DEF 32.2 HSC MODE:1 TA5

Milling with increased contour accuracy. The
TNC uses internally defined finishing filter settings
Input value 1:
Milling at an increased feed rate. The TNC uses
internally defined roughing filter settings
U Tolerance for rotary axes TA: Permissible position
error of rotary axes in degrees when M128 is active
(TCPM FUNCTION). The TNC always reduces the feed
rate in such a way that—if more than one axis is
traversed—the slowest axis moves at its maximum
feed rate. Rotary axes are usually much slower than
linear axes. You can significantly reduce the
machining time for programs for more than one axis
by entering a large tolerance value (e.g. 10°), since
the TNC does not always have to move the rotary axis
to the given nominal position. The contour will not be
damaged by entering a rotary axis tolerance value.
Only the position of the rotary axis with respect to the
workpiece surface will change. Input range 0 to
179.9999
The HSC MODE and TA parameters are only available if on

your machine you have software option 2 active (HSC
machining).

Using Touch Probe
Cycles
13.1 General Information about Touch Probe Cycles
13.1 General Information about
Touch Probe Cycles
The TNC must be specially prepared by the machine tool

builder for the use of a 3-D touch probe. The machine tool
manual provides further information.
If you are carrying out measurements during program run,

be sure that the tool data (length, radius) can be used from
the calibrated data or from the last TOOL CALL block
(selected with MP7411).
Method of function
Whenever the TNC runs a touch probe cycle, the 3-D touch probe
approaches the workpiece in one linear axis. This is also true during an
active basic rotation or with a tilted working plane. The machine tool
builder determines the probing feed rate in a machine parameter (see
“Before You Start Working with Touch Probe Cycles” later in this Z
chapter).
Y
When the probe stylus contacts the workpiece,
the 3-D touch probe transmits a signal to the TNC: the coordinates
of the probed position are stored, X
the touch probe stops moving, and F
returns to its starting position at rapid traverse.
If the stylus is not deflected within a distance defined in MP 6130, the F
F MAX
TNC displays an error message.
312 Using Touch Probe Cycles

Cycles in the Manual and El. Handwheel modes
In the Manual Operation and El. Handwheel modes, the TNC provides
touch probe cycles that allow you to:
Calibrate the touch probe
Compensate workpiece misalignment
Set datums
Touch probe cycles for automatic operation

Besides the touch probe cycles, which you can use in the Manual and
El. Handwheel modes, the TNC provides numerous cycles for a wide
variety of applications in automatic mode:
Calibrating a touch trigger probe
Compensating workpiece misalignment
Setting datums
Automatic workpiece inspection
Automatic tool measurement
You can program the touch probe cycles in the Programming and
Editing operating mode via the TOUCH PROBE key. Like the most
recent fixed cycles, touch probe cycles with numbers greater than 400
use Q parameters as transfer parameters. Parameters with specific
functions that are required in several cycles always have the same
number: For example, Q260 is always assigned the clearance height,
Q261 the measuring height, etc.
To simplify programming, the TNC shows a graphic during cycle
definition. In the graphic, the parameter that needs to be entered is
highlighted (see figure at right).

Defining the touch probe cycle in the Programming and Editing
mode of operation
U The soft-key row shows all available touch probe Example: NC blocks
functions divided into groups.
5 TCH PROBE 410 DATUM INSIDE RECTAN.
U Select the desired probe cycle, for example datum
setting. Cycles for automatic tool measurement are Q321=+50 ;CENTER IN 1ST AXIS
available only if your machine has been prepared for Q322=+50 ;CENTER IN 2ND AXIS
them.
U Select a cycle, e.g. datum setting at pocket. The TNC
initiates the programming dialog and asks for all Q324=20 ;2ND SIDE LENGTH
required input values. At the same time a graphic of Q261=-5 ;MEASURING HEIGHT
the input parameters is displayed in the right screen
window. The parameter that is asked for in the dialog Q320=0 ;SETUP CLEARANCE
prompt is highlighted. Q260=+20 ;CLEARANCE HEIGHT
U Enter all parameters requested by the TNC and Q301=0 ;MOVE TO CLEARANCE
conclude each entry with the ENT key.
Q305=10 ;NO. IN TABLE
U The TNC ends the dialog when all required data has Q331=+0 ;DATUM
been entered
Q332=+0 ;DATUM
Group of measuring cycles Soft key Page Q303=+1 ;MEAS. VALUE TRANSFER
Cycles for automatic measurement and Page 320 Q381=1 ;PROBE IN TS AXIS
compensation of workpiece
misalignment Q382=+85 ;1ST CO. FOR TS AXIS
Q383=+50 ;2ND CO. FOR TS AXIS
Cycles for automatic workpiece Page 342
presetting Q384=+0 ;3RD CO. FOR TS AXIS
Q333=+0 ;DATUM
Cycles for automatic workpiece Page 396
inspection
Calibration cycles, special cycles Page 446
Cycles for automatic kinematics Page 462

measurement
Cycles for automatic tool measurement Page 494

(enabled by the machine tool builder)

13.2 Before You Start Working with Touch Probe Cycles
13.2 Before You Start Working with
Touch Probe Cycles
To make it possible to cover the widest possible range of applications,
machine parameters enable you to determine the behavior common
to all touch probe cycles.
Maximum traverse to touch point: MP6130

If the stylus is not deflected within the path defined in MP6130, the
TNC outputs an error message.
Safety clearance to touch point: MP6140 Z

In MP6140 you define how far from the defined (or calculated) touch Y
point the TNC is to pre-position the touch probe. The smaller the value
you enter, the more exactly must you define the touch point position. X
In many touch probe cycles you can also define a setup clearance in
addition that is added to Machine Parameter 6140.
MP6130
Orient the infrared touch probe to the

programmed probe direction: MP6165
To increase measuring accuracy, you can use MP 6165 = 1 to have an
infrared touch probe oriented in the programmed probe direction
before every probe process. In this way the stylus is always deflected
in the same direction.
If you change MP6165, you must recalibrate the touch

probe, because its deflection behavior changes.
Z
Y
X
MP6140

Consider a basic rotation in the Manual
Operation mode: MP6166
Set MP 6166 = 1 for the TNC to consider an active basic rotation
during the probing process (the workpiece is approached along an
angular path if required) to ensure that the measuring accuracy for
probing individual positions is also increased in Setup mode.
This feature is not active during the following functions in

the Manual Operation mode:
Calibrate length
Calibrate radius
Measure basic rotation
Multiple measurement: MP6170

To increase measuring certainty, the TNC can run each probing
process up to three times in sequence. If the measured position
values differ too greatly, the TNC outputs an error message (the limit
value is defined in MP6171). With multiple measurement it is possible
to detect random errors, e.g. from contamination.
If the measured values lie within the confidence interval, the TNC
saves the mean value of the measured positions.
Confidence interval for multiple measurement:

MP6171
In MP6171 you store the value by which the results may differ when
you make multiple measurements. If the difference in the measured
values exceeds the value in MP6171, the TNC outputs an error
message.

Touch trigger probe, probing feed rate: MP6120
In MP6120 you define the feed rate at which the TNC is to probe the
workpiece.
Touch trigger probe, rapid traverse for Z

positioning: MP6150
Y
In MP6150 you define the feed rate at which the TNC pre-positions the
touch probe, or positions it between measuring points.
X
Touch trigger probe, rapid traverse for MP6120
positioning: MP6151 MP6360
MP6150
In MP6151 you define whether the TNC is to position the touch probe MP6361
at the feed rate defined in MP6150 or at rapid traverse.
Input value = 0: Position at feed rate from MP6150
Input value = 1: Pre-position at rapid traverse
KinematicsOpt: Tolerance limit in Optimization

mode: MP6600
In MP6600 you define the tolerance limit starting from which the TNC
displays a note in the Optimizing mode when the measured kinematic
data is greater than this limit value. The default value is 0.05. The larger
the machine, the greater these values should be.
Input range: 0.001 to 0.999
KinematicsOpt, permissible deviation of the

calibration ball radius: MP6601
In MP6601 you define the maximum permissible deviation from the
entered cycle parameter by the calibration ball radius measured in the
cycles.
Input range: 0.01 to 0.1
The TNC calculates the calibration ball radius twice at every measuring
point for all 5 touch points. If the radius is greater than Q407 +
MP6601 an error message appears because it could be contamination.
If the radius found by the TNC is less than 5 * (Q407 - MP6601), the
TNC also issues an error message.

Executing touch probe cycles
All touch probe cycles are DEF active. This means that the TNC runs
the cycle automatically as soon as the TNC executes the cycle
definition in the program run.
Make sure that at the beginning of the cycle the

compensation data (length, radius) from the calibrated
data or from the last TOOL CALL block are active
(selection via MP7411, see the User's Manual of the
iTNC530, “General User Parameters”).
You can also run the Touch Probe Cycles 408 to 419 during
an active basic rotation. Make sure, however, that the
basic rotation angle does not change when you use Cycle
7 DATUM SHIFT with datum tables after the measuring
cycle.
Touch probe cycles with a number greater than 400 position the touch
probe according to a positioning logic:
If the current coordinate of the south pole of the stylus is less than
the coordinate of the clearance height (defined in the cycle), the TNC
retracts the touch probe in the probe axis to the clearance height
and then positions it in the working plane to the first starting
position.
If the current coordinate of the south pole of the stylus is greater
than the coordinate of the clearance height, the TNC first positions
the probe in the working plane to the first starting position and then
moves it immediately to the measuring height in the touch probe
axis.

Touch Probe Cycles:
Automatic Measurement
of Workpiece
Misalignment
14.1 Fundamentals
14.1 Fundamentals
Overview
The TNC provides five cycles that enable you to measure and
compensate workpiece misalignment. In addition, you can reset a
basic rotation with Cycle 404:
Cycle Soft key Page

400 BASIC ROTATION Automatic Page 322
measurement using two points.
Compensation via basic rotation.
401 ROT OF 2 HOLES Automatic Page 325

measurement using two holes.
402 ROT OF 2 STUDS Automatic Page 328

measurement using two studs.
403 ROT IN ROTARY AXIS Automatic Page 331

measurement using two points.
Compensation by turning the table.
405 ROT IN C AXIS Automatic Page 336

alignment of an angular offset between
a hole center and the positive Y axis.
Compensation via table rotation.
404 SET BASIC ROTATION Setting any Page 335

basic rotation.
320 Touch Probe Cycles: Automatic Measurement of Workpiece Misalignment

14.1 Fundamentals
Characteristics common to all touch probe
cycles for measuring workpiece misalignment
Y
For Cycles 400, 401 and 402 you can define through parameter Q307
Default setting for basic rotation whether the measurement
result is to be corrected by a known angle α (see figure at right). This
enables you to measure the basic rotation against any straight line 1
1 Þ
of the workpiece and to establish the reference to the actual 0°
direction 2.
2

14.2 BASIC ROTATION (Cycle 400, DIN/ISO: G400)
14.2 BASIC ROTATION (Cycle 400,
DIN/ISO: G400)
Cycle run
Touch probe cycle 400 determines a workpiece misalignment by
measuring two points, which must lie on a straight surface. With the
basic rotation function the TNC compensates the measured value. Y
1 Following the positioning logic (see “Executing touch probe
cycles” on page 318), the TNC positions the touch probe to the
programmed probe starting point 1 at rapid traverse (value from
MP6150). The TNC offsets the touch probe by the safety clearance
in the direction opposite the defined traverse direction.
2 Then the touch probe moves to the entered measuring height and
probes the first touch point at the probing feed rate (MP6120).
2
3 Then the touch probe moves to the next starting position 2 and 1
probes the second position.
4 The TNC returns the touch probe to the clearance height and X
performs the basic rotation.
Before a cycle definition you must have programmed a

tool call to define the touch probe axis.
The TNC will reset an active basic rotation at the beginning
of the cycle.

Cycle parameters
U 1st meas. point 1st axis Q263 (absolute): +
Coordinate of the first touch point in the reference Q267
axis of the working plane. Input range -99999.9999 to Y +
99999.9999 Q272=2
U 1st meas. point 2nd axis Q264 (absolute):
Coordinate of the first touch point in the minor axis of
the working plane. Input range -99999.9999 to
99999.9999 Q266 MP6140
Q264 +
U 2nd meas. point 1st axis Q265 (absolute): Q320
Coordinate of the second touch point in the reference
axis of the working plane. Input range -99999.9999 to
99999.9999
X
U 2nd meas. point 2nd axis Q266 (absolute): Q272=1
Q263 Q265
Coordinate of the second touch point in the minor axis
of the working plane. Input range -99999.9999 to
99999.9999
U Measuring axis Q272: Axis in the working plane in
which the measurement is to be made:
1:Reference axis = measuring axis
2:Minor axis = measuring axis
U Traverse direction 1 Q267: Direction in which the
probe is to approach the workpiece:
-1:Negative traverse direction
+1: Positive traverse direction
U Measuring height in the touch probe axis Q261
(absolute): Coordinate of the ball tip center (= touch
point) in the touch probe axis in which the
measurement is to be made. Input range -
99999.9999 to 99999.9999
U Setup clearance Q320 (incremental): Additional
distance between measuring point and ball tip. Q320
is added to MP6140. Input range 0 to 99999.9999,
U Clearance height Q260 (absolute): Coordinate in the
touch probe axis at which no collision between touch
probe and workpiece (fixtures) can occur. Input range
-99999.9999 to 99999.9999, alternatively PREDEF

Example: NC blocks
U Traversing to clearance height Q301: Definition of
how the touch probe is to move between the
measuring points: 5 TCH PROBE 400 BASIC ROTATION
0: Move at measuring height between measuring Q263=+10 ;1ST POINT 1ST AXIS
points
1: Move at clearance height between measuring Q264=+3.5 ;1ST POINT 2ND AXIS
points Q265=+25 ;2ND POINT 1ST AXIS
Q266=+8 ;2ND POINT 2ND AXIS
U Default setting for basic rotation Q307
(absolute): If the misalignment is to be measured Q272=2 ;MEASURING AXIS
against a straight line other than the reference axis, Q267=+1 ;TRAVERSE DIRECTION
enter the angle of this reference line. The TNC will
then calculate the difference between the value Q261=-5 ;MEASURING HEIGHT
measured and the angle of the reference line for the Q320=0 ;SET-UP CLEARANCE
basic rotation. Input range -360.000 to 360.000
U Preset number in table Q305: Enter the preset
number in the table in which the TNC is to save the Q301=0 ;MOVE TO CLEARANCE
determined basic rotation. If you enter Q305=0, the Q307=0 ;PRESET BASIC ROTATION
TNC automatically places the determined basic
rotation in the ROT menu of the Manual Operation Q305=0 ;NO. IN TABLE
mode. Input range 0 to 2999

14.3 BASIC ROTATION from Two Holes (Cycle 401, DIN/ISO: G401)
14.3 BASIC ROTATION from Two
Holes (Cycle 401, DIN/ISO: G401)
Cycle run
The Touch Probe Cycle 401 measures the centers of two holes. Then
the TNC calculates the angle between the reference axis in the
working plane and the line connecting the two hole centers. With the Y
basic rotation function, the TNC compensates the calculated value. As
an alternative, you can also compensate the determined misalignment
by rotating the rotary table. 2
cycles” on page 318), the TNC positions the touch probe at rapid 1
traverse (value from MP6150) to the point entered as center of the
first hole 1.
2 Then the probe moves to the entered measuring height and
probes four points to find the first hole center.
3 The touch probe returns to the clearance height and then to the X
position entered as center of the second hole 2.
4 The TNC moves the touch probe to the entered measuring height
and probes four points to find the second hole center.
5 Then the TNC returns the touch probe to the clearance height and

of the cycle.
This touch probe cycle is not allowed when the tilted
working plane function is active.
If you want to compensate the misalignment by rotating
the rotary table, the TNC will automatically use the
following rotary axes:
C for tool axis Z
B for tool axis Y
A for tool axis X

Cycle parameters
U 1st hole: Center in 1st axis Q268 (absolute):
Center of the first hole in the reference axis of the
working plane. Input range -99999.9999 to Y
99999.9999
U 1st hole: Center in 2nd axis Q269 (absolute):
Center of the first hole in the minor axis of the Q271
working plane. Input range -99999.9999 to
99999.9999 Q269
U 2nd hole: Center in 1st axis Q270 (absolute):
Center of the second hole in the reference axis of the
99999.9999
U 2nd hole: Center in 2nd axis Q271 (absolute):
X
Q268 Q270
Center of the second hole in the minor axis of the
99999.9999
U Measuring height in the touch probe axis
Q261 (absolute): Coordinate of the ball tip
center (= touch point) in the touch probe axis in Z
which the measurement is to be made. Input
range -99999.9999 to 99999.9999
Q260
probe and workpiece (fixtures) can occur. Input range Q261
(absolute): If the misalignment is to be measured
against a straight line other than the reference axis,
enter the angle of this reference line. The TNC will X
then calculate the difference between the value
measured and the angle of the reference line for the

Example: NC blocks
U Preset number in table Q305: Enter the preset
number in the table in which the TNC is to save the
determined basic rotation. If you enter Q305=0, the 5 TCH PROBE 401 ROT OF 2 HOLES
TNC automatically places the determined basic Q268=+37 ;1ST CENTER IN 1ST AXIS
rotation in the ROT menu of the Manual Operation
mode. The parameter has no effect if the Q269=+12 ;1ST CENTER IN 2ND AXIS
misalignment is to be compensated by a rotation of Q270=+75 ;2ND CENTER IN 1ST AXIS
the rotary table (Q402=1). In this case the
misalignment is not saved as an angular value. Input Q271=+20 ;2ND CENTER IN 2ND AXIS
range 0 to 2999 Q261=-5 ;MEASURING HEIGHT
U Basic rotation / alignment Q402: Specify whether Q260=+20 ;CLEARANCE HEIGHT
the TNC should compensate misalignment with a
basic rotation, or by rotating the rotary table: Q307=0 ;PRESET BASIC ROTATION
0: Set basic rotation Q305=0 ;NO. IN TABLE
1: Rotate the rotary table
When you select rotary table, the TNC does not save Q402=0 ;ALIGNMENT
the measured misalignment, not even when you have Q337=0 ;SET TO ZERO
defined a table line in parameter Q305.
U Set to zero after alignment Q337: Definition of
whether the TNC should set the display of the aligned
rotary axis to zero:
0: Do not reset the display of the rotary axis to 0 after
alignment
1: Reset the display of the rotary axis to 0 after
alignment
The TNC sets the display to 0 only if you have defined
Q402=1.

14.4 BASIC ROTATION over Two Studs (Cycle 402, DIN/ISO: G402)
14.4 BASIC ROTATION over Two
Studs (Cycle 402, DIN/ISO:
G402)
Cycle run
The Touch Probe Cycle 402 measures the centers of two studs. Then
the TNC calculates the angle between the reference axis in the
working plane and the line connecting the two stud centers. With the Y
basic rotation function, the TNC compensates the calculated value. As
an alternative, you can also compensate the determined misalignment
by rotating the rotary table.
5
cycles” on page 318), the TNC positions the touch probe in rapid
traverse (value from MP6150) to the starting point 1 of the first 1
stud.
2 Then the probe moves to the entered measuring height 1 and
probes four points to find the center of the first stud. The touch
probe moves on a circular arc between the touch points, each of
which is offset by 90°.
X
3 The touch probe returns to the clearance height and then to the
starting point for probing 5 the second stud.
2 and probes four points to find the center of the second stud.
5 Then the TNC returns the touch probe to the clearance height and

of the cycle.
This touch probe cycle is not allowed when the tilted
working plane function is active.
If you want to compensate the misalignment by rotating
the rotary table, the TNC will automatically use the
following rotary axes:
C for tool axis Z
B for tool axis Y
A for tool axis X

Cycle parameters
U 1st stud: Center in 1st axis (absolute): Center of
the first stud in the reference axis of the working
plane. Input range -99999.9999 to 99999.9999 Y
U 1st stud: Center in 2nd axis Q269 (absolute):
Center of the first stud in the minor axis of the
working plane. Input range -99999.9999 to Q271 Q314
99999.9999
U Diameter of stud 1 Q313: Approximate diameter of Q269 Q313
the 1st stud. Enter a value that is more likely to be too
large than too small. Input range 0 to 99999.9999
U Measuring height 1 in the probe axis Q261
X
point in the touch probe axis) at which stud 1 is to be
Q268 Q270
measured. Input range -99999.9999 to 99999.9999
U 2nd stud: Center in 1st axis Q270 (absolute):
Center of the second stud in the reference axis of the
99999.9999
Z
U 2nd stud: Center in 2nd axis Q271 (absolute):
Center of the second stud in the minor axis of the
99999.9999 Q261
Q260
U Diameter of stud 2 Q314: Approximate diameter of Q315
the 2nd stud. Enter a value that is more likely to be
too large than too small. Input range 0 to 99999.9999
U Measuring height 2 in the probe axis Q315
point in the touch probe axis) at which stud 2 is to be MP6140 X
+
measured. Input range -99999.9999 to 99999.9999 Q320

Example: NC blocks
measuring points: 5 TCH PROBE 402 ROT OF 2 STUDS
0: Move at measuring height between measuring Q268=-37 ;1ST CENTER IN 1ST AXIS
points
1: Move at clearance height between measuring Q269=+12 ;1ST CENTER IN 2ND AXIS
points Q313=60 ;DIAMETER OF STUD 1
Q261=-5 ;MEASURING HEIGHT 1
Q270=+75 ;2ND CENTER IN 1ST AXIS
(absolute): If the misalignment is to be measured
against a straight line other than the reference axis, Q271=+20 ;2ND CENTER IN 2ND AXIS
enter the angle of this reference line. The TNC will
Q314=60 ;DIAMETER OF STUD 2
then calculate the difference between the value
measured and the angle of the reference line for the Q315=-5 ;MEASURING HEIGHT 2
U Preset number in table Q305: Enter the preset Q260=+20 ;CLEARANCE HEIGHT
determined basic rotation. If you enter Q305=0, the Q301=0 ;MOVE TO CLEARANCE
TNC automatically places the determined basic Q307=0 ;PRESET BASIC ROTATION
rotation in the ROT menu of the Manual Operation
mode. The parameter has no effect if the Q305=0 ;NO. IN TABLE
misalignment is to be compensated by a rotation of Q402=0 ;ALIGNMENT
the rotary table (Q402=1). In this case the
misalignment is not saved as an angular value. Input Q337=0 ;SET TO ZERO
range 0 to 2999
U Basic rotation / alignment Q402: Specify whether
the TNC should compensate misalignment with a
basic rotation, or by rotating the rotary table:
0: Set basic rotation
1: Rotate the rotary table
When you select rotary table, the TNC does not save
the measured misalignment, not even when you have
defined a table line in parameter Q305.
whether the TNC should set the display of the aligned
alignment
1: Reset the display of the rotary axis to 0 after
alignment
The TNC sets the display to 0 only if you have defined
Q402=1.

14.5 BASIC ROTATION Compensation via Rotary Axis (Cycle 403, DIN/ISO:
G403)
14.5 BASIC ROTATION
Compensation via Rotary Axis
Cycle run
Touch Probe Cycle 403 determines a workpiece misalignment by
measuring two points, which must lie on a straight surface. The TNC
compensates the determined misalignment by rotating the A, B or C
axis. The workpiece can be clamped in any position on the rotary table. Y
programmed starting point 1 at rapid traverse (value from
probes the first touch point at the probing feed rate (MP6120). 2
3 Then the touch probe moves to the next starting position 2 and 1
4 The TNC returns the touch probe to the clearance height and
X
moves the rotary axis, which was defined in the cycle, by the
measured value. Optionally you can have the display set to 0 after
alignment.

G403) Please note while programming:
You can now also use Cycle 403 when the "Tilt the
working plane" function is active. Ensure that the
clearance height is sufficiently large so that no collisions
can occur during the final positioning of the rotary axis.
The TNC does not check whether touch points and
compensation axis match. This can result in compensation
movements offset by 180°.

The order of the touch points influences the determined
compensation angle. Ensure that the coordinate of touch
point 1 in the axis perpendicular to the probing direction is
smaller than the coordinate of touch point 2.
The TNC stores the measured angle in parameter Q150.

G403)
Cycle parameters
99999.9999 Q272=2
U 1st meas. point 2nd axis Q264 (absolute): A
Coordinate of the first touch point in the minor axis of B
the working plane. Input range -99999.9999 to C
99999.9999 Q266 MP6140
Q264 +
99999.9999
X
Q263 Q265
99999.9999
U Measuring axis Q272: Axis in which the
measurement is to be made:
1: Reference axis = measuring axis Z
2: Minor axis = measuring axis
3: Touch probe axis = measuring axis
Q260
-1: Negative traverse direction
Q261
center (= touch point) in the touch probe axis in
which the measurement is to be made. Input X
range -99999.9999 to 99999.9999

Example: NC blocks
G403) U Clearance height Q260 (absolute): Coordinate in the
probe and workpiece (fixtures) can occur. Input range 5 TCH PROBE 403 ROT IN C-AXIS
-99999.9999 to 99999.9999, alternatively PREDEF Q263=+25 ;1ST POINT 1ST AXIS
U Traversing to clearance height Q301: Definition of Q264=+10 ;1ST POINT 2ND AXIS
measuring points: Q265=+40 ;2ND POINT 1ST AXIS
0: Move at measuring height between measuring Q266=+17 ;2ND POINT 2ND AXIS
points
1: Move at clearance height between measuring Q272=2 ;MEASURING AXIS
points Q267=+1 ;TRAVERSE DIRECTION
U Axis for compensation motion Q312: assignment of Q261=-5 ;MEASURING HEIGHT
the rotary axis in which the TNC is to compensate the
measured misalignment: Q320=0 ;SET-UP CLEARANCE
4: Compensate misalignment with rotary axis A Q260=+20 ;CLEARANCE HEIGHT
5: Compensate misalignment with rotary axis B
6: Compensate misalignment with rotary axis C Q301=0 ;MOVE TO CLEARANCE
Q312=6 ;COMPENSATION AXIS
whether the TNC should set the display of the aligned Q337=0 ;SET TO ZERO
alignment Q303=+1 ;MEAS. VALUE TRANSFER
1:Reset the display of the rotary axis to 0 after
Q380=+0 ;REFERENCE ANGLE
alignment
U Number in table Q305: Enter the number in the
preset table/datum table in which the TNC is to set
the rotary axis to zero. Only effective if Q337 is set to
1. Input range 0 to 2999
U Measured value transfer (0, 1) Q303: Specify if the
determined basic rotation is to be saved in the datum
table or in the preset table:
0: Write the measured basic rotation as a datum shift
in the active datum table. The reference system is the
active workpiece coordinate system.
1: Write the measured basic rotation into the preset
table. The reference system is the machine
coordinate system (REF system).
U Reference angle? (0=ref. axis) Q380: Angle with
which the TNC is to align the probed straight line.
Only effective if the rotary axis C is selected
(Q312=6). Input range -360.000 to 360.000

14.6 SET BASIC ROTATION (Cycle 404, DIN/ISO: G404)
14.6 SET BASIC ROTATION (Cycle
404, DIN/ISO: G404)
Cycle run
With Touch Probe Cycle 404, you can set any basic rotation Example: NC blocks
automatically during program run. This cycle is intended primarily for
resetting a previous basic rotation. 5 TCH PROBE 404 BASIC ROTATION
Q307=+0 ;PRESET BASIC ROTATION
Cycle parameters
U Preset value for basic rotation: Angular value
at which the basic rotation is to be set. Input
range -360.000 to 360.000
preset/datum table in which the TNC is to save the
defined basic rotation. Input range 0 to 2999

405, DIN/ISO: G405)
14.7 Compensating Workpiece Misalignment by Rotating the C Axis (Cycle
14.7 Compensating Workpiece
Misalignment by Rotating the C
Axis (Cycle 405, DIN/ISO: G405)
Cycle run
With Touch Probe Cycle 405, you can measure
Y
the angular offset between the positive Y axis of the active
coordinate system and the center of a hole, or
the angular offset between the nominal position and the actual 2
position of a hole center.
3 1
The TNC compensates the determined angular offset by rotating the 4
C axis. The workpiece can be clamped in any position on the rotary
table, but the Y coordinate of the hole must be positive. If you
measure the angular misalignment of the hole with touch probe axis Y X
(horizontal position of the hole), it may be necessary to execute the
cycle more than once because the measuring strategy causes an
inaccuracy of approx. 1% of the misalignment.
starting point 1 at rapid traverse (value from MP6150). The TNC
calculates the probe starting points from the data in the cycle and
the safety clearance from MP6140.
Y
probes the first touch point at the probing feed rate (MP6120). The
TNC derives the probing direction automatically from the
programmed starting angle.
3 Then the touch probe moves in a circular arc either at measuring
height or at clearance height to the next starting point 2 and probes
the second touch point.
4 The TNC positions the probe to starting point 3 and then to starting
point 4 to probe the third and fourth touch points and positions the X
touch probe on the hole centers measured.
5 Finally the TNC returns the touch probe to the clearance height and
aligns the workpiece by rotating the table. The TNC rotates the
rotary table so that the hole center after compensation lies in the
direction of the positive Y axis, or on the nominal position of the
hole center—both with a vertical and horizontal touch probe axis.
The measured angular misalignment is also available in parameter
Q150.

405, DIN/ISO: G405)
To prevent a collision between the touch probe and the
workpiece, enter a low estimate for the nominal diameter
of the pocket (or hole).
If the dimensions of the pocket and the safety clearance
do not permit pre-positioning in the proximity of the touch
points, the TNC always starts probing from the center of
the pocket. In this case the touch probe does not return to
the clearance height between the four measuring points.
The smaller the angle, the less accurately the TNC can
calculate the circle center. Minimum input value: 5°.

405, DIN/ISO: G405)
Cycle parameters
hole in the reference axis of the working plane. Input
range -99999.9999 to 99999.9999 Y
U Center in 2nd axis Q322 (absolute value): Center
of the hole in the minor axis of the working plane. If
you program Q322 = 0, the TNC aligns the hole Q247
center to the positive Y axis. If you program Q322 Q325
Q262
not equal to 0, then the TNC aligns the hole center Q322
to the nominal position (angle of the hole center).
Input range -99999.9999 to 99999.9999
U Nominal diameter Q262: Approximate diameter of the
circular pocket (or hole). Enter a value that is more
likely to be too small than too large. Input range 0 to X
99999.9999 Q321
reference axis of the working plane and the first touch
point. Input range -360.000 to 360.000
two measuring points. The algebraic sign of the
stepping angle determines the direction of rotation
(negative = clockwise) in which the touch probe
moves to the next measuring point. If you wish to
probe a circular arc instead of a complete circle, then
program the stepping angle to be less than 90°. Input
range -120.000 to 120.000

405, DIN/ISO: G405)
Q261 (absolute): Coordinate of the ball tip Z
range -99999.9999 to 99999.9999
U Setup clearance Q320 (incremental): Additional Q260
alternatively PREDEF Q261
probe and workpiece (fixtures) can occur. Input range MP6140 X
-99999.9999 to 99999.9999, alternatively PREDEF +
Q320
measuring points:
0: Move at measuring height between measuring Example: NC blocks
points
1: Move at clearance height between measuring 5 TCH PROBE 405 ROT IN C AXIS
points
whether the TNC should set the display of the C axis Q262=10 ;NOMINAL DIAMETER
to zero, or write the angular offset in column C of the Q325=+0 ;STARTING ANGLE
datum table:
0: Set display of C to 0 Q247=90 ;STEPPING ANGLE
>0: Write the angular misalignment, including Q261=-5 ;MEASURING HEIGHT
algebraic sign, in the datum table. Line number =
value of Q337. If a C-axis shift is registered in the Q320=0 ;SETUP CLEARANCE
datum table, the TNC adds the measured angular Q260=+20 ;CLEARANCE HEIGHT
misalignment.
Q337=0 ;SET TO ZERO

405, DIN/ISO: G405)
Example: Determining a basic rotation from two holes
Y Y
35
15
X Z
25 80
0 BEGIN PGM CYC401 MM

1 TOOL CALL 69 Z
2 TCH PROBE 401 ROT 2 HOLES
Q268=+25 ;1ST CENTER IN 1ST AXIS Center of the 1st hole: X coordinate
Q269=+15 ;1ST CENTER IN 2ND AXIS Center of the 1st hole: Y coordinate
Q270=+80 ;2ND CENTER IN 1ST AXIS Center of the 2nd hole: X coordinate
Q271=+35 ;2ND CENTER IN 2ND AXIS Center of the 2nd hole: Y coordinate
Q261=-5 ;MEASURING HEIGHT Coordinate in the touch probe axis in which the measurement is
made
Q260=+20 ;CLEARANCE HEIGHT Height in the touch probe axis at which the probe can traverse
without collision
Q307=+0 ;PRESET BASIC ROTATION Angle of the reference line
Q402=1 ;ALIGNMENT Compensate misalignment by rotating the rotary table
Q337=1 ;SET TO ZERO Set the display to zero after the alignment
3 CALL PGM 35K47 Part program call
4 END PGM CYC401 MM

Touch Probe Cycles:
Automatic Datum
Setting
15.1 Fundamentals
15.1 Fundamentals
Overview
The TNC offers twelve cycles for automatically finding reference
points and handling them as follows:
Setting the determined values directly as display values
Entering the determined values in the preset table
Entering the determined values in a datum table
Cycle Soft key Page
408 SLOT CENTER REF PT. Measuring Page 345
the inside width of a slot, and defining
the slot center as datum
409 RIDGE CENTER REF PT. Measuring Page 349

the outside width of a ridge, and defining
the ridge center as datum
410 DATUM INSIDE RECTAN. Page 352

Measuring the inside length and width of
a rectangle, and defining the center as
datum
411 DATUM OUTSIDE RECTAN. Page 356

Measuring the outside length and width
of a rectangle, and defining the center as
datum
412 DATUM INSIDE CIRCLE Measuring Page 360

any four points on the inside of a circle,
and defining the center as datum
413 DATUM OUTSIDE CIRCLE Page 364

Measuring any four points on the
outside of a circle, and defining the
center as datum
414 DATUM OUTSIDE CORNER Page 368

Measuring two lines from the outside of
the angle, and defining the intersection
as datum
415 DATUM INSIDE CORNER Page 373

Measuring two lines from within the
angle, and defining the intersection as
datum
416 DATUM CIRCLE CENTER (2nd soft- Page 377

key level) Measuring any three holes on
a bolt hole circle, and defining the bolt-
hole center as datum
342 Touch Probe Cycles: Automatic Datum Setting

15.1 Fundamentals
Cycle Soft key Page
417 DATUM IN TS AXIS (2nd soft-key Page 381
level) Measuring any position in the
touch probe axis and defining it as datum
418 DATUM FROM 4 HOLES (2nd soft- Page 383

key level) Measuring 4 holes crosswise
and defining the intersection of the lines
between them as datum
419 DATUM IN ONE AXIS (2nd soft-key Page 387

level) Measuring any position in any axis
and defining it as datum
Characteristics common to all touch probe

cycles for datum setting
You can also run the Touch Probe Cycles 408 to 419 during
an active rotation (basic rotation or Cycle 10).
Datum point and touch probe axis

From the touch probe axis that you have defined in the measuring
program the TNC determines the working plane for the datum:
Active touch probe axis Datum setting in

Z or W X and Y
Y or V Z and X
X or U Y and Z

15.1 Fundamentals
Saving the calculated datum
In all cycles for datum setting you can use the input parameters Q303
and Q305 to define how the TNC is to save the calculated datum:
Q305 = 0, Q303 = any value
The TNC sets the calculated datum in the display. The new datum is
active immediately. At the same time, the TNC saves the datum set
in the display by the cycle in line 0 of the preset table.
Q305 not equal to 0, Q303 = -1
This combination can only occur if you

read in programs containing Cycles 410 to 418 created
on a TNC 4xx
read in programs containing Cycles 410 to 418 created
with an older software version on an iTNC 530
did not specifically define the measured-value transfer
with parameter Q303 when defining the cycle.
In these cases the TNC outputs an error message, since
the complete handling of REF-referenced datum tables
has changed. You must define a measured-value transfer
yourself with parameter Q303.
Q305 not equal to 0, Q303 = 0

The TNC writes the calculated datum in the active datum table. The
reference system is the active workpiece coordinate system. The
value of parameter Q305 determines the datum number. Activate
datum with Cycle 7 in the part program.
Q305 not equal to 0, Q303 = 1
The TNC writes the calculated datum in the preset table. The
reference system is the machine coordinate system (REF
coordinates). The value of parameter Q305 determines the preset
number. Activate preset with Cycle 247 in the part program.
Measurement results in Q parameters

The TNC saves the measurement results of the respective touch
probe cycle in the globally effective Q parameters Q150 to Q160. You
can use these parameters in your program. Note the table of result
parameters that are listed with every cycle description.

15.2 SLOT CENTER REF PT (Cycle 408, DIN/ISO: G408, FCL 3 Function)
15.2 SLOT CENTER REF PT
FCL 3 Function)
Cycle run
Touch Probe Cycle 408 finds the center of a slot and defines its center
as datum. If desired, the TNC can also enter the coordinates into a
datum table or the preset table.
Y
starting point 1 at rapid traverse (value from MP6150). The TNC
calculates the probe starting points from the data in the cycle and
the safety clearance from MP6140. 1
2
3 Then the touch probe moves either paraxially at the measuring
height or linearly at the clearance height to the next starting point
2 and probes the second touch point.
X
processes the determined datum depending on the cycle
parameters Q303 and Q305 (see “Saving the calculated datum”
on page 344) and saves the actual values in the Q parameters
listed below.
5 If desired, the TNC subsequently measures the datum in the touch
probe axis in a separate probing.
Parameter number Meaning

Q166 Actual value of measured slot width
Q157 Actual value of the centerline

To prevent a collision between touch probe and
workpiece, enter a low estimate for the slot width.
If the slot width and the safety clearance do not permit
pre-positioning in the proximity of the touch points, the
TNC always starts probing from the center of the slot. In
this case the touch probe does not return to the clearance
height between the two measuring points.
Cycle parameters
slot in the reference axis of the working plane. Input MP6140
range -99999.9999 to 99999.9999 Y +
Q320
slot in the minor axis of the working plane. Input
range -99999.9999 to 99999.9999
U Width of slot Q311 (incremental): Width of the slot,
Q311
regardless of its position in the working plane. Input Q322
range 0 to 99999.9999
U Measuring axis (1=1st axis / 2=2nd axis) Q272:
Axis in which the measurement is to be made:
1: Reference axis = measuring axis
2: Minor axis = measuring axis X
Q321
99999.9999 to 99999.9999
Z
Q260

measuring points:
0: Move at measuring height between measuring
points
1: Move at clearance height between measuring
points
datum/preset table in which the TNC is to save the
coordinates of the slot center. If you enter Q305=0,
the TNC automatically sets the display so that the
new datum is on the slot center. Input range 0 to
2999
U New datum Q405 (absolute): Coordinate in the
measuring axis at which the TNC should set the
calculated slot center. Default setting = 0. Input
range: -99999.9999 to 99999.9999
U Measured-value transfer (0, 1) Q303: Specify
whether the determined datum is to be saved in the
datum table or in the preset table:
0: Write determined datum in the active datum table.
The reference system is the active workpiece
coordinate system.
1: Write determined datum in the preset table. The
reference system is the machine coordinate system
(REF system).

Example: NC blocks
U Probe in TS axis Q381: Specify whether the TNC
should also set the datum in the touch probe axis:
0: Do not set datum in the touch probe axis 5 TCH PROBE 408 SLOT CENTER REF PT
1: Set datum in the touch probe axis Q321=+50 ;CENTER IN 1ST AXIS
U Probe TS axis: Coord. 1st axis Q382 (absolute): Q322=+50 ;CENTER IN 2ND AXIS
Coordinate of the probe point in the reference axis of
the working plane at which point the datum is to be Q311=25 ;SLOT WIDTH
set in the touch probe axis. Only effective if Q381 = Q272=1 ;MEASURING AXIS
1. Input range –99999.9999 to 99999.9999
Q261=-5 ;MEASURING HEIGHT
U Probe TS axis: Coord. 2nd axis Q383 (absolute):
Coordinate of the probe point in the minor axis of the Q320=0 ;SETUP CLEARANCE
working plane at which point the datum is to be set in Q260=+20 ;CLEARANCE HEIGHT
the touch probe axis. Only effective if Q381 = 1. Input
range –99999.9999 to 99999.9999 Q301=0 ;MOVE TO CLEARANCE
U Probe TS axis: Coord. 3rd axis Q384 (absolute):
Coordinate of the probe point in the touch probe Q405=+0 ;DATUM
axis, at which point the datum is to be set in the
Q303=+1 ;MEAS. VALUE TRANSFER
touch probe axis. Only effective if Q381 = 1. Input
range –99999.9999 to 99999.9999 Q381=1 ;PROBE IN TS AXIS
U New datum in TS axis Q333 (absolute): Coordinate in Q382=+85 ;1ST CO. FOR TS AXIS
the touch probe axis at which the TNC should set the Q383=+50 ;2ND CO. FOR TS AXIS
datum. Default setting = 0. Input range: –99999.9999
to 99999.9999 Q384=+0 ;3RD CO. FOR TS AXIS
Q333=+1 ;DATUM

15.3 RIDGE CENTER REF PT (Cycle 409, DIN/ISO: G409, FCL 3 function)
15.3 RIDGE CENTER REF PT
FCL 3 function)
Cycle run
Touch Probe Cycle 409 finds the center of a ridge and defines its
center as datum. If desired, the TNC can also enter the coordinates
into a datum table or the preset table.
Y
probe starting point 1 at rapid traverse (value from MP6150). The 2
TNC calculates the probe starting points from the data in the cycle
and the safety clearance from MP6140.
3 Then the touch probe moves at clearance height to the next touch 1
point 2 and probes the second touch point.
X
listed below.

Q166 Actual value of measured ridge width
workpiece, enter a high estimate for the ridge width.

Cycle parameters
ridge in the reference axis of the working plane. Input MP6140
range -99999.9999 to 99999.9999 Y +
Q320
ridge in the minor axis of the working plane. Input
range -99999.9999 to 99999.9999
U Width of ridge Q311 (incremental): Width of the
Q311
ridge, regardless of its position in the working plane. Q322
U Measuring axis (1=1st axis / 2=2nd axis) Q272:
Axis in which the measurement is to be made:
2: Minor axis = measuring axis X
Q321
range -99999.9999 to 99999.9999
Z
Q260
touch probe axis at which no collision between touch Q261
datum/preset table in which the TNC is to save the X
coordinates of the ridge center. If you enter Q305=0,
the TNC automatically sets the display so that the
new datum is on the slot center. Input range 0 to
2999
U New datum Q405 (absolute): Coordinate in the
measuring axis at which the TNC should set the
calculated ridge center. Default setting = 0. Input
range: -99999.9999 to 99999.9999

Example: NC blocks
datum table or in the preset table: 5 TCH PROBE 409 SLOT CENTER RIDGE
0: Write determined datum in the active datum table. Q321=+50 ;CENTER IN 1ST AXIS
coordinate system. Q322=+50 ;CENTER IN 2ND AXIS
1: Write determined datum in the preset table. The Q311=25 ;RIDGE WIDTH
(REF system). Q272=1 ;MEASURING AXIS
U Probe in TS axis Q381: Specify whether the TNC Q261=-5 ;MEASURING HEIGHT
should also set the datum in the touch probe axis: Q320=0 ;SETUP CLEARANCE
0: Do not set datum in the touch probe axis
1: Set datum in the touch probe axis Q260=+20 ;CLEARANCE HEIGHT
U Probe TS axis: Coord. 1st axis Q382 (absolute): Q305=10 ;NO. IN TABLE
Coordinate of the probe point in the reference axis of Q405=+0 ;DATUM
the working plane at which point the datum is to be
set in the touch probe axis. Only effective if Q381 = Q303=+1 ;MEAS. VALUE TRANSFER
1. Input range –99999.9999 to 99999.9999 Q381=1 ;PROBE IN TS AXIS
U Probe TS axis: Coord. 2nd axis Q383 (absolute): Q382=+85 ;1ST CO. FOR TS AXIS
Coordinate of the probe point in the minor axis of the
working plane at which point the datum is to be set in
the touch probe axis. Only effective if Q381 = 1. Input Q384=+0 ;3RD CO. FOR TS AXIS
range –99999.9999 to 99999.9999
Q333=+1 ;DATUM
Coordinate of the probe point in the touch probe
range –99999.9999 to 99999.9999
U New datum in TS axis Q333 (absolute): Coordinate in
the touch probe axis at which the TNC should set the
to 99999.9999

15.4 DATUM FROM INSIDE OF RECTANGLE (Cycle 410, DIN/ISO: G410)
15.4 DATUM FROM INSIDE OF
RECTANGLE (Cycle 410,
DIN/ISO: G410)
Cycle run
Touch Probe Cycle 410 finds the center of a rectangular pocket and
defines its center as datum. If desired, the TNC can also enter the
coordinates into a datum table or the preset table.
Y
probe starting point 1 at rapid traverse (value from MP6150). The
4
2 Then the touch probe moves to the entered measuring height and 1 3
probes the first touch point at the probing feed rate (MP6120). 2
2 and probes the second touch point.
X
point 4 to probe the third and fourth touch points.
on page 344).
probe axis in a separate probing and saves the actual values in the
following Q parameters.
Q151 Actual value of center in reference axis
Q152 Actual value of center in minor axis
Q154 Actual value of length in the reference

axis
Q155 Actual value of length in the minor axis

workpiece, enter low estimates for the lengths of the 1st
and 2nd sides.
Cycle parameters
pocket in the reference axis of the working plane.
Input range -99999.9999 to 99999.9999 Y Q323
pocket in the minor axis of the working plane. Input
range -99999.9999 to 99999.9999
U First side length Q323 (incremental): Pocket length,
Q324
Q322
parallel to the reference axis of the working plane.
MP6140
Input range 0 to 99999.9999 +
Q320
U 2nd side length Q324 (incremental): Pocket length,
range 0 to 99999.9999
X
U Measuring height in the touch probe axis Q261 Q321
99999.9999 to 99999.9999
U Setup clearance Q320 (incremental): Additional Z
U Clearance height Q260 (absolute): Coordinate in the Q260
-99999.9999 to 99999.9999, alternatively PREDEF Q261

measuring points:
points
points
U Datum number in table Q305: Enter the number in the
coordinates of the pocket center. If you enter
Q305=0, the TNC automatically sets the display so
that the new datum is at the center of the pocket.
Input range 0 to 2999
U New datum for reference axis Q331 (absolute):
Coordinate in the reference axis at which the TNC
should set the pocket center. Default setting = 0.
Input range: –99999.9999 to 99999.9999
U New datum for minor axis Q332 (absolute):
Coordinate in the minor axis at which the TNC should
set the pocket center. Default setting = 0. Input
range: –99999.9999 to 99999.9999
-1: Do not use. Is entered by the TNC when old
programs are read in (see “Saving the calculated
datum” on page 344).
coordinate system.
(REF system).

Example: NC blocks

0: Do not set datum in the touch probe axis 5 TCH PROBE 410 DATUM INSIDE RECTAN.
the working plane at which point the datum is to be Q323=60 ;FIRST SIDE LENGTH
set in the touch probe axis. Only effective if Q381 = Q324=20 ;2ND SIDE LENGTH
1. Input range –99999.9999 to 99999.9999
Q332=+0 ;DATUM
range –99999.9999 to 99999.9999 Q303=+1 ;MEAS. VALUE TRANSFER
U New datum in TS axis Q333 (absolute): Coordinate in Q381=1 ;PROBE IN TS AXIS
the touch probe axis at which the TNC should set the Q382=+85 ;1ST CO. FOR TS AXIS
to 99999.9999 Q383=+50 ;2ND CO. FOR TS AXIS
Q384=+0 ;3RD CO. FOR TS AXIS
Q333=+1 ;DATUM

15.5 DATUM FROM OUTSIDE OF RECTANGLE (Cycle 411, DIN/ISO: G411)
15.5 DATUM FROM OUTSIDE OF
RECTANGLE (Cycle 411,
DIN/ISO: G411)
Cycle run
Touch Probe Cycle 411 finds the center of a rectangular stud and
coordinates into a datum table or the preset table. Y
cycles” on page 318), the TNC positions the touch probe to the 4
3 Then the touch probe moves either paraxially at the measuring 2
2 and probes the second touch point. X
on page 344).
probe axis in a separate probing and saves the actual values in the
following Q parameters.

axis

To prevent a collision between the touch probe and
workpiece, enter high estimates for the lengths of the 1st
and 2nd sides.
Cycle parameters
stud in the reference axis of the working plane. Input MP6140
+
range -99999.9999 to 99999.9999 Y Q323 Q320
stud in the minor axis of the working plane. Input
range -99999.9999 to 99999.9999
U
Q324
First side length Q323 (incremental): Stud length,
parallel to the reference axis of the working plane Q322
U 2nd side length Q324 (incremental): Stud length,
range 0 to 99999.9999
X
range -99999.9999 to 99999.9999
U Setup clearance Q320 (incremental): Additional Z
U Clearance height Q260 (absolute): Coordinate in the Q260

measuring points:
points
points
U Datum number in table Q305: Enter the datum
that the new datum is on the stud center. Input range
0 to 2999
should set the stud center. Default setting = 0. Input
range: –99999.9999 to 99999.9999
set the stud center. Default setting = 0. Input range:
–99999.9999 to 99999.9999
coordinate system.
(REF system).

Example: NC blocks

0: Do not set datum in the touch probe axis 5 TCH PROBE 411 DATUM OUTSIDE RECTAN.
the working plane at which point the datum is to be Q323=60 ;FIRST SIDE LENGTH
set in the touch probe axis. Only effective if Q381 = Q324=20 ;2ND SIDE LENGTH
1. Input range –99999.9999 to 99999.9999
Q332=+0 ;DATUM
Q333=+1 ;DATUM

15.6 DATUM FROM INSIDE OF CIRCLE (Cycle 412, DIN/ISO: G412)
CIRCLE (Cycle 412, DIN/ISO:
G412)
Cycle run
Touch Probe Cycle 412 finds the center of a circular pocket (or of a
hole) and defines its center as datum. If desired, the TNC can also
enter the coordinates into a datum table or the preset table. Y
TNC calculates the probe starting points from the data in the cycle 2
and the safety clearance from MP6140. 3 1
probes the first touch point at the probing feed rate (MP6120). The 4
3 Then the touch probe moves in a circular arc either at measuring X
listed below.

Q153 Actual value of diameter

To prevent a collision between the touch probe and the
workpiece, enter a low estimate for the nominal diameter
of the pocket (or hole).
The smaller the angle increment Q247, the less accurately
the TNC can calculate the datum. Minimum input value: 5°
Cycle parameters
pocket in the reference axis of the working plane.
Input range -99999.9999 to 99999.9999 Y
pocket in the minor axis of the working plane. If you
program Q322 = 0, the TNC aligns the hole center to Q247
the positive Y axis. If you program Q322 not equal to Q325
Q262
0, then the TNC aligns the hole center to the nominal Q322
position. Input range -99999.9999 to 99999.9999
circular pocket (or hole). Enter a value that is more
likely to be too small than too large. Input range 0 to
99999.9999 X
Q321
two measuring points. The algebraic sign of the
stepping angle determines the direction of rotation
(negative = clockwise) in which the touch probe
probe a circular arc instead of a complete circle, then
program the stepping angle to be less than 90°. Input
range -120.0000 to 120.0000

(absolute): Coordinate of the ball tip center (= touch Z
99999.9999 to 99999.9999
alternatively PREDEF Q261
probe and workpiece (fixtures) can occur. Input range MP6140 X
-99999.9999 to 99999.9999, alternatively PREDEF +
Q320
measuring points:
points
points
that the new datum is at the center of the pocket.
Input range 0 to 2999
should set the pocket center. Default setting = 0.
Input range: –99999.9999 to 99999.9999
set the pocket center. Default setting = 0. Input
range: –99999.9999 to 99999.9999
coordinate system.
(REF system).

Example: NC blocks

0: Do not set datum in the touch probe axis 5 TCH PROBE 412 DATUM INSIDE CIRCLE
the working plane at which point the datum is to be Q262=75 ;NOMINAL DIAMETER
set in the touch probe axis. Only effective if Q381 = Q325=+0 ;STARTING ANGLE
1. Input range –99999.9999 to 99999.9999
Coordinate of the probe point in the minor axis of the Q261=-5 ;MEASURING HEIGHT
working plane at which point the datum is to be set in Q320=0 ;SETUP CLEARANCE
range –99999.9999 to 99999.9999 Q260=+20 ;CLEARANCE HEIGHT
Coordinate of the probe point in the touch probe Q305=12 ;NO. IN TABLE
Q331=+0 ;DATUM
range –99999.9999 to 99999.9999 Q332=+0 ;DATUM
U New datum in TS axis Q333 (absolute): Coordinate in Q303=+1 ;MEAS. VALUE TRANSFER
the touch probe axis at which the TNC should set the Q381=1 ;PROBE IN TS AXIS
to 99999.9999 Q382=+85 ;1ST CO. FOR TS AXIS
U No. of measuring points (4/3) Q423: Specify Q383=+50 ;2ND CO. FOR TS AXIS
whether the TNC should measure the hole with 4 or Q384=+0 ;3RD CO. FOR TS AXIS
3 probing points:
4: Use 4 measuring points (standard setting) Q333=+1 ;DATUM
3: Use 3 measuring points Q423=4 ;NO. OF MEAS. POINTS
U Type of traverse? Line=0/Arc=1 Q365: Definition of Q365=1 ;TYPE OF TRAVERSE
the path function with which the tool is to move
between the measuring points if “traverse to
clearance height” (Q301=1) is active.
0: Move between operations on a straight line
1: Move between operations on the pitch circle

15.7 DATUM FROM OUTSIDE OF CIRCLE (Cycle 413, DIN/ISO: G413)
CIRCLE (Cycle 413, DIN/ISO:
G413)
Cycle run
Touch Probe Cycle 413 finds the center of a circular stud and defines
it as datum. If desired, the TNC can also enter the coordinates into a
datum table or the preset table. Y
1 Following the positioning logic (see “Executing touch probe 2
programmed starting angle. 4
3 Then the touch probe moves in a circular arc either at measuring X
listed below.


workpiece, enter a high estimate for the nominal diameter
of the stud.
The smaller the angle increment Q247, the less
accurately the TNC can calculate the datum. Minimum
input value: 5°.
Cycle parameters
stud in the reference axis of the working plane. Input
range -99999.9999 to 99999.9999 Y
stud in the minor axis of the working plane. If you Q247
program Q322 = 0, the TNC aligns the hole center to
the positive Y axis. If you program Q322 not equal to Q325
Q262
0, then the TNC aligns the hole center to the nominal Q322
position. Input range -99999.9999 to 99999.9999
stud. Enter a value that is more likely to be too large
than too small. Input range 0 to 99999.9999
X
Q321
U Stepping angle Q247 (incremental): Angle
between two measuring points. The algebraic sign
of the stepping angle determines the direction of
rotation (- = clockwise) in which the touch probe
probe a circular arc instead of a complete circle,
then program the stepping angle to be less than
90°. Input range -120.0000 to 120.0000

point) in the touch probe axis in which the Z
99999.9999 to 99999.9999
Q260
is added to MP6140. Input range 0 to 99999.9999, Q261
-99999.9999 to 99999.9999, alternatively PREDEF MP6140 X
+
U Traversing to clearance height Q301: Definition of Q320
measuring points:
points
points
that the new datum is on the stud center. Input range
0 to 2999
should set the stud center. Default setting = 0. Input
range: –99999.9999 to 99999.9999
set the stud center. Default setting = 0. Input range:
–99999.9999 to 99999.9999
coordinate system.
(REF system).

Example: NC blocks

0: Do not set datum in the touch probe axis 5 TCH PROBE 413 DATUM OUTSIDE CIRCLE
set in the touch probe axis. Only effective if Q381 = Q325=+0 ;STARTING ANGLE
1. Input range –99999.9999 to 99999.9999
Coordinate of the probe point in the minor axis of the Q261=-5 ;MEASURING HEIGHT
working plane at which point the datum is to be set in Q320=0 ;SETUP CLEARANCE
Coordinate of the probe point in the touch probe Q305=15 ;NO. IN TABLE
Q331=+0 ;DATUM
range –99999.9999 to 99999.9999 Q332=+0 ;DATUM
U New datum in TS axis Q333 (absolute): Coordinate in Q303=+1 ;MEAS. VALUE TRANSFER
the touch probe axis at which the TNC should set the Q381=1 ;PROBE IN TS AXIS
datum. Basic setting = 0
Q382=+85 ;1ST CO. FOR TS AXIS
U No. of measuring points (4/3) Q423: Specify
whether the TNC should measure the stud with 4 or Q383=+50 ;2ND CO. FOR TS AXIS
3 probing points: Q384=+0 ;3RD CO. FOR TS AXIS
4: Use 4 measuring points (standard setting)
3: Use 3 measuring points Q333=+1 ;DATUM
U Type of traverse? Line=0/Arc=1 Q365: Definition of Q423=4 ;NO. OF MEAS. POINTS

the path function with which the tool is to move Q365=1 ;TYPE OF TRAVERSE

15.8 DATUM FROM OUTSIDE OF CORNER (Cycle 414, DIN/ISO: G414)
CORNER (Cycle 414, DIN/ISO:
G414)
Cycle run
Touch Probe Cycle 414 finds the intersection of two lines and defines
it as the datum. If desired, the TNC can also enter the intersection into
a datum table or preset table. Y
cycles” on page 318), the TNC positions the touch probe at rapid
traverse (value from MP6150) to the first touch point 1 (see figure
at upper right). The TNC offsets the touch probe by the safety 4
clearance in the direction opposite the respective traverse
direction. 3
TNC derives the probing direction automatically from the 2
1
programmed 3rd measuring point.
X
3 Then the touch probe moves to the next starting position 2 and
5 Finally the TNC returns the touch probe to the clearance height and Y Y

on page 344) and saves the coordinates of the determined corner
in the Q parameters listed below 3 3
A B
probe axis in a separate probing. 1 2 X 2 1 X
Parameter number Meaning Y Y

2 1 1 2
Q151 Actual value of corner in reference axis C D
3 3
Q152 Actual value of corner in minor axis
X X

Y Y
The TNC always measures the first line in the direction of
the minor axis of the working plane. 3 3
A B
By defining the positions of the measuring points 1 and 3 1 2 2 1

X X
you also determine the corner at which the TNC sets the
datum (see figure at right and table at lower right). Y Y
2 1 1 2
C D
Corner X coordinate Y coordinate 3 3
A Point 1 greater than Point 1 less than point 3
point 3
X X
B Point 1 less than point 3 Point 1 less than point 3
C Point 1 less than point 3 Point 1 greater than point 3
D Point 1 greater than Point 1 greater than point 3

point 3

Cycle parameters
U 1st meas. point 1st axis Q263 (absolute):
Coordinate of the first touch point in the reference
axis of the working plane. Input range -99999.9999 to Y
99999.9999
Q296
Q327
99999.9999
Q297 Q264
U Spacing in 1st axis Q326 (incremental): Distance
between the first and second measuring points in the MP6140
reference axis of the working plane. Input range 0 to +
Q320
99999.9999
Q326
U 3rd meas. point 1st axis Q296 (absolute):
X
Q263
Coordinate of the third touch point in the reference
99999.9999
U 3rd meas. point 2nd axis Q297 (absolute):
Coordinate of the third touch point in the minor axis of
the working plane. Input range -99999.9999 to Y
99999.9999
U Spacing in 2nd axis Q327 (incremental): Distance Q260
between third and fourth measuring points in the
minor axis of the working plane. Input range 0 to Q261
99999.9999
range -99999.9999 to 99999.9999 X

measuring points:
points
points
U Execute basic rotation Q304: Definition of whether
the TNC should compensate workpiece misalignment
with a basic rotation:
0: No basic rotation
1: Basic rotation
number in the datum or preset table in which the TNC
is to save the coordinates of the corner. If you enter
that the new datum is on the corner. Input range 0 to
2999
should set the corner. Default setting = 0. Input
range: –99999.9999 to 99999.9999
set the calculated corner. Default setting = 0. Input
range: –99999.9999 to 99999.9999
coordinate system.
(REF system).

Example: NC blocks
0: Do not set datum in the touch probe axis 5 TCH PROBE 414 DATUM INSIDE CORNER
1: Set datum in the touch probe axis Q263=+37 ;1ST POINT 1ST AXIS
U Probe TS axis: Coord. 1st axis Q382 (absolute): Q264=+7 ;1ST POINT 2ND AXIS
the working plane at which point the datum is to be Q326=50 ;SPACING IN 1ST AXIS
set in the touch probe axis. Only effective if Q381 = Q296=+95 ;3RD POINT 1ST AXIS
1. Input range –99999.9999 to 99999.9999
Coordinate of the probe point in the minor axis of the Q327=45 ;SPACING IN 2ND AXIS
working plane at which point the datum is to be set in Q261=-5 ;MEASURING HEIGHT
range –99999.9999 to 99999.9999 Q320=0 ;SETUP CLEARANCE
Coordinate of the probe point in the touch probe Q301=0 ;MOVE TO CLEARANCE
Q304=0 ;BASIC ROTATION
range –99999.9999 to 99999.9999 Q305=7 ;NO. IN TABLE
U New datum in TS axis Q333 (absolute): Coordinate in Q331=+0 ;DATUM
the touch probe axis at which the TNC should set the Q332=+0 ;DATUM
to 99999.9999 Q303=+1 ;MEAS. VALUE TRANSFER
Q381=1 ;PROBE IN TS AXIS
Q333=+1 ;DATUM

15.9 DATUM FROM INSIDE OF CORNER (Cycle 415, DIN/ISO: G415)
CORNER (Cycle 415, DIN/ISO:
G415)
Cycle run
Touch Probe Cycle 415 finds the intersection of two lines and defines
it as the datum. If desired, the TNC can also enter the intersection into
a datum table or preset table. Y
traverse (value from MP6150) to the first touch point 1 (see figure 4
at upper right) that you have defined in the cycle. The TNC offsets
the touch probe by the safety clearance in the direction opposite
the respective traverse direction. 3
probing direction is derived from the number by which you identify
the corner.
X
on page 344) and saves the coordinates of the determined corner
in the Q parameters listed below
Q151 Actual value of corner in reference axis
Q152 Actual value of corner in minor axis


The TNC always measures the first line in the direction of
the minor axis of the working plane.
Cycle parameters
Coordinate of the first touch point in the reference MP6140
Y +
axis of the working plane. Input range -99999.9999 to Q320
99999.9999
Coordinate of the first touch point in the minor axis of Q308=4 Q308=3
99999.9999
Q327
U Spacing in 1st axis Q326 (incremental): Distance Q308=1 Q308=2
between the first and second measuring points in the
reference axis of the working plane. Input range 0 to Q264
99999.9999
Q326
U Spacing in 2nd axis Q327 (incremental): Distance
X
Q263
between third and fourth measuring points in the
minor axis of the working plane. Input range 0 to
99999.9999
U Corner Q308: Number identifying the corner which
the TNC is to set as datum. Input range 1 to 4
Z
Q260
99999.9999 to 99999.9999
distance between measuring point and ball tip. Q320 Q261
U Clearance height Q260 (absolute): Coordinate in the X

measuring points:
points
points
U Execute basic rotation Q304: Definition of whether
the TNC should compensate workpiece misalignment
with a basic rotation:
0: No basic rotation
1: Basic rotation
number in the datum or preset table in which the TNC
is to save the coordinates of the corner. If you enter
that the new datum is on the corner. Input range 0 to
2999
should set the corner. Default setting = 0. Input
range: –99999.9999 to 99999.9999
set the calculated corner. Default setting = 0. Input
range: –99999.9999 to 99999.9999
coordinate system.
(REF system).

Example: NC blocks
0: Do not set datum in the touch probe axis 5 TCH PROBE 415 DATUM OUTSIDE CORNER
1: Set datum in the touch probe axis Q263=+37 ;1ST POINT 1ST AXIS
U Probe TS axis: Coord. 1st axis Q382 (absolute): Q264=+7 ;1ST POINT 2ND AXIS
the working plane at which point the datum is to be Q326=50 ;SPACING IN 1ST AXIS
set in the touch probe axis. Only effective if Q381 = Q296=+95 ;3RD POINT 1ST AXIS
1. Input range –99999.9999 to 99999.9999
Coordinate of the probe point in the minor axis of the Q327=45 ;SPACING IN 2ND AXIS
range –99999.9999 to 99999.9999 Q320=0 ;SETUP CLEARANCE
Coordinate of the probe point in the touch probe Q301=0 ;MOVE TO CLEARANCE
Q304=0 ;BASIC ROTATION
range –99999.9999 to 99999.9999 Q305=7 ;NO. IN TABLE
U New datum in TS axis Q333 (absolute): Coordinate in Q331=+0 ;DATUM
to 99999.9999 Q303=+1 ;MEAS. VALUE TRANSFER
Q333=+1 ;DATUM

15.10 DATUM CIRCLE CENTER (Cycle 416, DIN/ISO: G416)
15.10 DATUM CIRCLE CENTER
Cycle run
Touch Probe Cycle 416 finds the center of a bolt hole circle and
coordinates into a datum table or the preset table. Y
1
traverse (value from MP6150) to the point entered as center of the
first hole 1. 2
position entered as center of the second hole 2. 3
and probes four points to find the second hole center. X
position entered as center of the third hole 3.
and probes four points to find the third hole center.
listed below.

Q153 Actual value of bolt hole circle diameter


Cycle parameters
U Center in 1st axis Q273 (absolute): Bolt hole circle
center (nominal value) in the reference axis of the
working plane. Input range -99999.9999 to Y
99999.9999
Q291
U Center in 2nd axis Q274 (absolute): Bolt hole circle
center (nominal value) in the minor axis of the working
Q292
Q274 62
U Nominal diameter Q262: Enter the approximate bolt Q2
hole circle diameter. The smaller the hole diameter,
the more exact the nominal diameter must be. Input
range -0 to 99999.9999
U Angle of 1st hole Q291 (absolute): Polar coordinate Q293
angle of the first hole center in the working plane.
X
Q273
Input range -360.0000 to 360.0000
U Angle of 2nd hole Q292 (absolute): Polar coordinate
angle of the second hole center in the working plane.
Input range -360.0000 to 360.0000
U Angle of 3rd hole Q293 (absolute): Polar coordinate Y
angle of the third hole center in the working plane.
Input range -360.0000 to 360.0000
99999.9999 to 99999.9999
probe and workpiece (fixtures) can occur. Input range X

datum or preset table in which the TNC is to save the
coordinates of the bolt-hole circle center. If you enter
that the new datum is on the bolt hole center. Input
range 0 to 2999
should set the bolt-hole center. Default setting = 0.
Input range: –99999.9999 to 99999.9999
set the bolt-hole center. Default setting = 0. Input
range: –99999.9999 to 99999.9999
coordinate system.
(REF system).

Example: NC blocks
0: Do not set datum in the touch probe axis 5 TCH PROBE 416 DATUM CIRCLE CENTER
set in the touch probe axis. Only effective if Q381 = Q291=+34 ;ANGLE OF 1ST HOLE
1. Input range –99999.9999 to 99999.9999
Q292=+70 ;ANGLE OF 2ND HOLE
Coordinate of the probe point in the minor axis of the Q293=+210 ;ANGLE OF 3RD HOLE
Q332=+0 ;DATUM
U Setup clearance Q320 (incremental): Additional Q384=+0 ;3RD CO. FOR TS AXIS
distance between measuring point and ball tip. Q320 Q333=+1 ;DATUM
is added to MP6140, and is only effective when the
datum is probed in the touch probe axis. Input range Q320=0 ;SETUP CLEARANCE

15.11 DATUM IN TOUCH PROBE AXIS (Cycle 417, DIN/ISO: G417)
15.11 DATUM IN TOUCH PROBE AXIS
Cycle run
Touch Probe Cycle 417 measures any coordinate in the touch probe
axis and defines it as datum. If desired, the TNC can also enter the
measured coordinate in a datum table or preset table. Z
MP6150). The TNC offsets the touch probe by the safety clearance Q260
in the positive direction of the touch probe axis.
2 Then the touch probe moves in its own axis to the coordinate
entered as starting point 1 and measures the actual position with
a simple probing movement.
processes the determined datum depending on the cycle X
listed below

Q160 Actual value of measured point

tool call to define the touch probe axis. The TNC then sets
the datum in this axis.

15.11 DATUM IN TOUCH PROBE AXIS (Cycle 417, DIN/ISO: G417)
Cycle parameters
Coordinate of the first touch point in the reference
99999.9999 Y
99999.9999 1
Q264
U 1st meas. point 3rd axis Q294 (absolute):
Coordinate of the first touch point in the touch probe
axis. Input range -99999.9999 to 99999.9999
distance between measuring point and ball tip. Q320 X
probe and workpiece (fixtures) can occur. Input range Z
MP6140
Q320
+
coordinate. If you enter Q305=0, the TNC 1 Q260
automatically sets the display so that the new datum
Q294
is on the probed surface. Input range 0 to 2999
the touch probe axis at which the TNC should set the
to 99999.9999
X
programs are read in (see “Saving the calculated Example: NC blocks
0: Write determined datum in the active datum table. 5 TCH PROBE 417 DATUM IN TS AXIS
The reference system is the active workpiece Q263=+25 ;1ST POINT 1ST AXIS
coordinate system.
1: Write determined datum in the preset table. The Q264=+25 ;1ST POINT 2ND AXIS
reference system is the machine coordinate system Q294=+25 ;1ST POINT 3RD AXIS
(REF system).
Q333=+0 ;DATUM
Q303=+1 ;MEAS. VALUE TRANSFER

15.12 DATUM AT CENTER OF 4 HOLES (Cycle 418, DIN/ISO: G418)
15.12 DATUM AT CENTER OF 4
HOLES (Cycle 418, DIN/ISO:
G418)
Cycle run
Touch Probe Cycle 418 calculates the intersection of the lines
connecting opposite holes and sets the datum at the intersection. If Y
desired, the TNC can also enter the intersection into a datum table or
preset table.
cycles” on page 318), the TNC positions the touch probe at rapid 4 3
traverse (value from MP6150) to the center of the first hole 1.
3 The touch probe returns to the clearance height and then to the 1 2
and probes four points to find the second hole center. X
5 The TNC repeats steps 3 and 4 for the holes 3 and 4.
on page 344). The TNC calculates the datum as the intersection of
the lines connecting the centers of holes 1/3 and 2/4 and saves the
actual values in the Q parameters listed below.
Q151 Actual value of intersection point in
reference axis
Q152 Actual value of intersection point in

minor axis


Cycle parameters
U First center in 1st axis Q268 (absolute): center
of the 1st hole in the reference axis of the working Y Q318 Q316
U First center in 2nd axis Q269 (absolute): center
of the 1st hole in the minor axis of the working Q319 Q317
of the 2nd hole in the reference axis of the
99999.9999 Q269 Q271
U First center in 2nd axis Q271 (absolute): center
of the 2nd hole in the minor axis of the working
X
Q268 Q270
of the 3rd hole in the reference axis of the working
U 3rd center in 2nd axis Q317 (absolute): center
of the 3rd hole in the minor axis of the working Z
U 4th center in 1st axis Q318 (absolute): center
of the 4th hole in the reference axis of the working
plane. Input range -99999.9999 to 99999.9999 Q260
U 4th center in 2nd axis Q319 (absolute): center Q261
of the 4th hole in the minor axis of the working
(absolute): Coordinate of the ball tip center (=
touch point) in the touch probe axis in which the X
99999.9999 to 99999.9999

coordinates of the line intersection. If you enter
that the new datum is at the intersection of the
connecting lines. Input range 0 to 2999
should set the calculated intersection of the
connecting lines. Default setting = 0. Input range:
-99999.9999 to 99999.9999
set the calculated intersection of the connecting
lines. Default setting = 0. Input range: -99999.9999 to
99999.9999
coordinate system.
(REF system).

Example: NC blocks
0: Do not set datum in the touch probe axis 5 TCH PROBE 418 DATUM FROM 4 HOLES
1: Set datum in the touch probe axis Q268=+20 ;1ST CENTER IN 1ST AXIS
U Probe TS axis: Coord. 1st axis Q382 (absolute): Q269=+25 ;1ST CENTER IN 2ND AXIS
the working plane at which point the datum is to be Q270=+150 ;2ND CENTER IN 1ST AXIS
set in the touch probe axis. Only effective if Q381 = 1. Q271=+25 ;2ND CENTER IN 2ND AXIS
U Probe TS axis: Coord. 2nd axis Q383 (absolute): Q316=+150 ;3RD CENTER IN 1ST AXIS
Coordinate of the probe point in the minor axis of the
working plane at which point the datum is to be set in Q317=+85 ;3RD CENTER IN 2ND AXIS
the touch probe axis. Only effective if Q381 = 1. Input Q318=+22 ;4TH CENTER IN 1ST AXIS
range –99999.9999 to 99999.9999
Q319=+80 ;4TH CENTER IN 2ND AXIS
Coordinate of the probe point in the touch probe
axis, at which point the datum is to be set in the Q260=+10 ;CLEARANCE HEIGHT
range –99999.9999 to 99999.9999
Q331=+0 ;DATUM
datum. Default setting = 0. Input range: –99999.9999 Q303=+1 ;MEAS. VALUE TRANSFER
to 99999.9999
Q333=+0 ;DATUM

15.13 DATUM IN ONE AXIS (Cycle 419, DIN/ISO: G419)
15.13 DATUM IN ONE AXIS
Cycle run
Touch Probe Cycle 419 measures any coordinate in any axis and +
MP6140 + Q320
defines it as datum. If desired, the TNC can also enter the measured Q267
coordinate in a datum table or preset table.
Y +
1 Following the positioning logic (see “Executing touch probe Q272=2
in the direction opposite the programmed probing direction. 1
Q264
2 Then the touch probe moves to the programmed measuring height
and measures the actual position with a simple probing
movement.
parameters Q303 and Q305 (see “Saving the calculated datum” X
on page 344). Q263 Q272=1

If you use Cycle 419 several times in succession to save
the datum in more than one axis in the preset table, you
must activate the preset number last written to by Cycle
419 after every execution of Cycle 419 (this is not required
if you overwrite the active preset).

Cycle parameters
MP6140 + Q320
99999.9999 Y +
Q272=2
99999.9999 1
Q264
range -99999.9999 to 99999.9999
X
U Setup clearance Q320 (incremental): Additional Q263 Q272=1
+
touch probe axis at which no collision between touch Z
probe and workpiece (fixtures) can occur. Input range Q272=3 Q267

U Measuring axis (1...3: 1=reference axis) Q272:
Q260
Axis in which the measurement is to be made: Q261 1
Axis assignment
Active touch Corresponding Corresponding X
probe axis: reference axis: minor axis: Q272=1
Q272= 3 Q272 = 1 Q272 = 2
Z X Y
Y Z X
X Y Z

Example: NC blocks

U Traverse direction Q267: Direction in which the
-1: Negative traverse direction 5 TCH PROBE 419 DATUM IN ONE AXIS
+1: Positive traverse direction Q263=+25 ;1ST POINT 1ST AXIS
U Datum number in table Q305: Enter the number in the Q264=+25 ;1ST POINT 2ND AXIS
coordinate. If you enter Q305=0, the TNC Q261=+25 ;MEASURING HEIGHT
automatically sets the display so that the new datum Q320=0 ;SETUP CLEARANCE
is on the probed surface. Input range 0 to 2999
U New datum Q333 (absolute): Coordinate at which the
TNC should set the datum. Default setting = 0. Input Q272=+1 ;MEASURING AXIS
range: –99999.9999 to 99999.9999 Q267=+1 ;TRAVERSE DIRECTION
U Measured-value transfer (0, 1) Q303: Specify Q305=0 ;NO. IN TABLE
Q333=+0 ;DATUM
-1: Do not use. See “Saving the calculated datum” on Q303=+1 ;MEAS. VALUE TRANSFER
page 344
coordinate system.
(REF system).

Example: Datum setting in center of a circular segment and on top surface of
workpiece
Y Y
25
30
X Z
25 25

1 TOOL CALL 69 Z Call tool 0 to define the touch probe axis

2 TCH PROBE 413 DATUM OUTSIDE CIRCLE
Q321=+25 ;CENTER IN 1ST AXIS Center of circle: X coordinate
Q322=+25 ;CENTER IN 2ND AXIS Center of circle: Y coordinate
Q262=30 ;NOMINAL DIAMETER Circle diameter
Q325=+90 ;STARTING ANGLE Polar coordinate angle for 1st touch point
Q247=+45 ;STEPPING ANGLE Stepping angle for calculating the starting points 2 to 4
Q261=-5 ;MEASURING HEIGHT Coordinate in the touch probe axis in which the measurement is
made
Q320=2 ;SETUP CLEARANCE Safety clearance in addition to MP6140
without collision
Q301=0 ;MOVE TO CLEARANCE Do not move to clearance height between measuring points
Q305=0 ;NO. IN TABLE Set display
Q331=+0 ;DATUM Set the display in X to 0
Q332=+10 ;DATUM Set the display in Y to 10
Q303=+0 ;MEAS. VALUE TRANSFER Without function, since display is to be set
Q381=1 ;PROBE IN TS AXIS Also set datum in the touch probe axis
Q382=+25 ;1ST CO. FOR TS AXIS X coordinate of touch point
Q383=+25 ;2ND CO. FOR TS AXIS Y coordinate of touch point
Q384=+25 ;3RD CO. FOR TS AXIS Z coordinate of touch point
Q333=+0 ;DATUM Set the display in Z to 0
Q423=4 ;NO. OF MEAS. POINTS Number of measuring points
Q365=1 ;TYPE OF TRAVERSE Position on circular arc or linearly to the next touch point
3 CALL PGM 35K47 Part program call
4 END PGM CYC413 MM

Example: Datum setting on top surface of workpiece and in center of a bolt hole circle
The measured bolt hole center shall be written in

the preset table so that it may be used at a later
time. Y Y
2
35
50
3
X Z
35 20

1 TOOL CALL 69 Z Call tool 0 to define the touch probe axis
2 TCH PROBE 417 DATUM IN TS AXIS Cycle definition for datum setting in the touch probe axis
Q263=+7.5 ;1ST POINT 1ST AXIS Touch point: X coordinate
Q264=+7.5 ;1ST POINT 2ND AXIS Touch point: Y coordinate
Q294=+25 ;1ST POINT 3RD AXIS Touch point: Z coordinate
without collision
Q305=1 ;NO. IN TABLE Write Z coordinate in line 1
Q333=+0 ;DATUM Set touch-probe axis to 0
Q303=+1 ;MEAS. VALUE TRANSFER In the preset table PRESET.PR, save the calculated datum
referenced to the machine-based coordinate system (REF system)

3 TCH PROBE 416 DATUM CIRCLE CENTER
Q273=+35 ;CENTER IN 1ST AXIS Center of the bolt hole circle: X coordinate
Q274=+35 ;CENTER IN 2ND AXIS Center of the bolt hole circle: Y coordinate
Q262=50 ;NOMINAL DIAMETER Diameter of the bolt hole circle
Q291=+90 ;ANGLE OF 1ST HOLE Polar coordinate angle for 1st hole center 1
Q292=+180 ;ANGLE OF 2ND HOLE Polar coordinate angle for 2nd hole center 2
Q293=+270 ;ANGLE OF 3RD HOLE Polar coordinate angle for 3rd hole center 3
Q261=+15 ;MEASURING HEIGHT Coordinate in the touch probe axis in which the measurement is
made
without collision
Q305=1 ;NO. IN TABLE Enter center of bolt hole circle (X and Y) in line 1
Q331=+0 ;DATUM
Q332=+0 ;DATUM
Q303=+1 ;MEAS. VALUE TRANSFER In the preset table PRESET.PR, save the calculated datum
referenced to the machine-based coordinate system (REF system)
Q381=0 ;PROBE IN TS AXIS Do not set a datum in the touch probe axis
Q382=+0 ;1ST CO. FOR TS AXIS No function
Q383=+0 ;2ND CO. FOR TS AXIS No function
Q384=+0 ;3RD CO. FOR TS AXIS No function
Q333=+0 ;DATUM No function
4 CYCL DEF 247 DATUM SETTING Activate new preset with Cycle 247
Q339=1 ;DATUM NUMBER
6 CALL PGM 35KLZ Part program call
7 END PGM CYC416 MM

394
Touch Probe Cycles: Automatic Datum Setting
Touch Probe Cycles:
Automatic Workpiece
Inspection
16.1 Fundamentals
16.1 Fundamentals
Overview
The TNC offers twelve cycles for measuring workpieces
automatically.
Cycle Soft key Page

0 REFERENCE PLANE Measuring a Page 402
coordinate in a selectable axis
1 POLAR DATUM PLANE Measuring a Page 403

point in a probing direction
420 MEASURE ANGLE Measuring an Page 405

angle in the working plane
421 MEASURE HOLE Measuring the Page 408

position and diameter of a hole
422 MEAS. CIRCLE OUTSIDE Page 412

Measuring the position and diameter of
a circular stud
423 MEAS. RECTAN. INSIDE Measuring Page 416

the position, length and width of a
rectangular pocket
424 MEAS. RECTAN. OUTSIDE Page 420

Measuring the position, length and
width of a rectangular stud
425 MEASURE INSIDE WIDTH (2nd Page 424

soft-key row) Measuring slot width
426 MEASURE RIDGE WIDTH (2nd soft- Page 427

key row) Measuring the width of a ridge
427 MEASURE COORDINATE (2nd soft- Page 430

key row) Measuring any coordinate in a
selectable axis
430 MEAS. BOLT HOLE CIRC. (2nd soft- Page 433

key row) Measuring position and
diameter of a bolt hole circle
431 MEASURE PLANE (2nd soft-key Page 437

row) Measuring the A and B axis angles
of a plane
396 Touch Probe Cycles: Automatic Workpiece Inspection

16.1 Fundamentals
Recording the results of measurement
For all cycles in which you automatically measure workpieces (with
the exception of Cycles 0 and 1), you can have the TNC record the
measurement results. In the respective probing cycle you can define
if the TNC is to
Save the measuring log to a file
Interrupt the program run and display the measuring log on the
screen
Create no measuring log
If you want to save the measuring log as a file, the TNC, by default,
saves the measuring log as an ASCII file in the directory from which
you run the measuring program. As an alternative, you can also send
the measuring log directly to a printer or transfer it to a PC via the data
interface. To do this, set the print function (in the interface
configuration menu) to RS232:\ (see also the User's Manual under
“MOD Functions, Setting Up the Data Interface”).
All measured values listed in the log file are referenced to

the datum active during the respective cycle you are
running. In addition, the coordinate system may have been
rotated in the plane or the plane may have been tilted by
using 3D-ROT. In this case, the TNC converts the
measuring results to the respective active coordinate
system.
Use the HEIDENHAIN data transfer software TNCremo if
you wish to output the measuring log via the data
interface.

16.1 Fundamentals
Example: Measuring log for touch probe cycle 421:
Measuring log for Probing Cycle 421 Hole Measuring
Date: 30-06-2005
Time: 6:55:04
Measuring program: TNC:\GEH35712\CHECK1.H
Nominal values: Center in reference axis: 50.0000
Center in minor axis: 65.0000
Diameter: 12.0000
Given limit values:Maximum dimension for center in reference axis:
50.1000 Minimum limit for center in reference axis: 49.9000
Maximum limit for center in minor axis: 65.1000
Minimum limit for center in minor axis: 64.9000
Maximum dimension for hole: 12.0450
Minimum dimension for hole: 12.0000
Actual values: Center in reference axis: 50.0810
Center in minor axis: 64.9530
Diameter: 12.0259
Deviations: Center in reference axis: 0.0810
Center in minor axis: -0.0470
Diameter: 0.0259
Further measuring results: Measuring height: -5.0000
End of measuring log

16.1 Fundamentals
Measurement results in Q parameters
The TNC saves the measurement results of the respective touch
probe cycle in the globally effective Q parameters Q150 to Q160.
Deviations from the nominal value are saved in the parameters Q161
to Q166. Note the table of result parameters that are listed with every
cycle description.
During cycle definition the TNC also shows the result parameters for
the respective cycle in a help graphic (see figure at upper right). The
highlighted result parameter belongs to that input parameter.
Classification of results
For some cycles you can inquire the status of measuring results
through the globally effective Q parameters Q180 to Q182:
Class of results Parameter value

Measurement results are within tolerance Q180 = 1
Rework is required Q181 = 1
Scrap Q182 = 1
The TNC sets the rework or scrap marker as soon as one of the
measuring values falls outside of tolerance. To determine which of the
measuring results lies outside of tolerance, check the measuring log,
or compare the respective measuring results (Q150 to Q160) with
their limit values.
In Cycle 427 the TNC assumes that you are measuring an outside
dimension (stud). However, you can correct the status of the
measurement by entering the correct maximum and minimum
dimension together with the probing direction.
The TNC also sets the status markers if you have not
defined any tolerance values or maximum/minimum
dimensions.

16.1 Fundamentals
Tolerance monitoring
For most of the cycles for workpiece inspection you can have the TNC
perform tolerance monitoring. This requires that you define the
necessary limit values during cycle definition. If you do not wish to
monitor for tolerances, simply leave the 0 (the default value) in the
monitoring parameters.
Tool monitoring
For some cycles for workpiece inspection you can have the TNC
perform tool monitoring. The TNC then monitors whether
The tool radius should be compensated because of the deviations
from the nominal value (values in Q16x).
The deviations from the nominal value (values in Q16x) are greater
than the tool breakage tolerance.
Tool compensation
This function works only:

If the tool table is active.
If tool monitoring is switched on in the cycle (enter a tool
name or Q330 unequal to 0). Select the tool name input
by soft key. The TNC no longer displays the right single
quotation mark.
If you perform several compensation measurements, the
TNC adds the respective measured deviation to the value
stored in the tool table.
The TNC always compensates the tool radius in the DR column of the
tool table, even if the measured deviation lies within the given
tolerance. You can inquire whether re-working is necessary via
Parameter Q181 in the NC program (Q181=1: must be reworked).
For Cycle 427:
If an axis of the active working plane is defined as measuring axis
(Q272 = 1 or 2), the TNC compensates the tool radius as described
above. From the defined traversing direction (Q267) the TNC
determines the direction of compensation.
If the touch probe axis is defined as measuring axis (Q272 = 3), the
TNC compensates the tool length.

16.1 Fundamentals
Tool breakage monitoring
This function works only:

If the tool table is active.
If tool monitoring is switched on in the cycle (enter Q330
not equal to 0).
If the breakage tolerance RBREAK for the tool number
entered in the table is greater than 0 (see also the User's
Manual, section 5.2 “Tool Data”).
The TNC will output an error message and stop program run if the
measured deviation is greater than the breakage tolerance of the tool.
At the same time the tool will be deactivated in the tool table (column
TL = L).
Reference system for measurement results

The TNC transfers all the measurement results to the result
parameters and the protocol file in the active coordinate system, or as
the case may be, the shifted or/and rotated/tilted coordinate system.

16.2 REF. PLANE (Cycle 0, DIN/ISO: G55)
16.2 REF. PLANE (Cycle 0, DIN/ISO:
G55)
Cycle run
1 The touch probe moves at rapid traverse (value from MP6150) to
the starting position 1 programmed in the cycle.
2 Then the touch probe approaches the workpiece at the feed rate
assigned in MP6120. The probing direction is to be defined in the Z
cycle.
3 After the TNC has saved the position, the probe retracts to the
1
starting point and saves the measured coordinate in a Q
parameter. The TNC also stores the coordinates of the touch probe
position at the time of the triggering signal in the parameters Q115
to Q119. For the values in these parameters the TNC does not
account for the stylus length and radius.
Pre-position the touch probe in order to avoid a collision
when the programmed pre-positioning point is
approached.
Cycle parameters
U Parameter number for result: Enter the number of Example: NC blocks
the Q parameter to which you want to assign the
coordinate. Input range 0 to 1999 67 TCH PROBE 0.0 REF. PLANE Q5 X-
U Probing axis/Probing direction: Enter the probing 68 TCH PROBE 0.1 X+5 Y+0 Z-5
axis with the axis selection keys or ASCII keyboard
and the algebraic sign for the probing direction.
Confirm your entry with the ENT key. Input range: All
NC axes
U Nominal position value: Use the axis selection keys
or the ASCII keyboard to enter all coordinates of the
nominal pre-positioning point values for the touch
probe. Input range -99999.9999 to 99999.9999
U To conclude the input, press the ENT key.

16.3 POLAR REFERENCE PLANE (Cycle 1)
16.3 POLAR REFERENCE PLANE
(Cycle 1)
Cycle run
Touch Probe Cycle 1 measures any position on the workpiece in any
direction.
Y
the starting position 1 programmed in the cycle.
2 Then the touch probe approaches the workpiece at the feed rate
assigned in MP6120. During probing the TNC moves
simultaneously in 2 axes (depending on the probing angle). The
scanning direction is defined by the polar angle entered in the 1
cycle.
3 After the TNC has saved the position, the probe returns to the
starting point. The TNC also stores the coordinates of the touch
probe position at the time of the triggering signal in parameters
Q115 to Q119. X
Pre-position the touch probe in order to avoid a collision
when the programmed pre-positioning point is
approached.
The probing axis defined in the cycle specifies the probing

plane:
Probing axis X: X/Y plane
Probing axis Y: Y/Z plane
Probing axis Z: Z/X plane

16.3 POLAR REFERENCE PLANE (Cycle 1)
Cycle parameters
U Probing axis: Enter the probing axis with the axis Example: NC blocks
selection keys or ASCII keyboard. Confirm your entry
with the ENT key. Input range: X, Y or Z 67 TCH PROBE 1.0 POLAR REFERENCE PLANE
U Probing angle: Angle, measured from the probing 68 TCH PROBE 1.1 X ANGLE: +30
axis, at which the touch probe is to move. Input range 69 TCH PROBE 1.2 X+5 Y+0 Z-5
-180.0000 to 180.0000
U Nominal position value: Use the axis selection keys
or the ASCII keyboard to enter all coordinates of the
nominal pre-positioning point values for the touch
probe. Input range -99999.9999 to 99999.9999
U To conclude the input, press the ENT key.

16.4 MEASURE ANGLE (Cycle 420, DIN/ISO: G420)
16.4 MEASURE ANGLE (Cycle 420,
DIN/ISO: G420)
Cycle run
Touch Probe Cycle 420 measures the angle that any straight surface
on the workpiece describes with respect to the reference axis of the
working plane. Y
2
1
4 The TNC returns the touch probe to the clearance height and saves X
the measured angle in the following Q parameter:
Q150 The measured angle is referenced to the
reference axis of the machining plane.

If touch probe axis = measuring axis, set Q263 equal to
Q265 if the angle about the A axis is to be measured; set
Q263 not equal to Q265 if the angle is to be measured about
the B axis.

Cycle parameters
99999.9999 Q272=2
99999.9999 Q266 MP6140
Q264 +
99999.9999
X
Q263 Q265
99999.9999
U Measuring axis Q272: Axis in which the
measurement is to be made:

99999.9999 to 99999.9999
-99999.9999 to 99999.9999, alternatively PREDEF Example: NC blocks
U Traversing to clearance height Q301: Definition of 5 TCH PROBE 420 MEASURE ANGLE
measuring points: Q263=+10 ;1ST POINT 1ST AXIS
0: Move at measuring height between measuring Q264=+10 ;1ST POINT 2ND AXIS
points
1: Move at clearance height between measuring Q265=+15 ;2ND POINT 1ST AXIS
points Q266=+95 ;2ND POINT 2ND AXIS
Q272=1 ;MEASURING AXIS
U Measuring log Q281: Definition of whether the TNC is
to create a measuring log: Q267=-1 ;TRAVERSE DIRECTION
0: No measuring log Q261=-5 ;MEASURING HEIGHT
1: Generate measuring log: with the standard setting
the TNC saves the log file TCHPR420.TXT in the Q320=0 ;SETUP CLEARANCE
directory in which your measuring program is also Q260=+10 ;CLEARANCE HEIGHT
stored.
2: Interrupt the program run and display the Q301=1 ;MOVE TO CLEARANCE
measuring log on the screen. Resume program run Q281=1 ;MEASURING LOG
with NC Start.

16.5 MEASURE HOLE (Cycle 421, DIN/ISO: G421)
16.5 MEASURE HOLE (Cycle 421,
DIN/ISO: G421)
Cycle run
Touch Probe Cycle 421 measures the center and diameter of a hole (or
circular pocket). If you define the corresponding tolerance values in
the cycle, the TNC makes a nominal-to-actual value comparison and Y
saves the deviation value in system parameters.
3
and the safety clearance from MP6140. 1
2 Then the touch probe moves to the entered measuring height and 4
X
saves the actual values and the deviations in the following Q
parameters:

Q161 Deviation at center of reference axis
Q162 Deviation at center of minor axis
Q163 Deviation from diameter

calculate the hole dimensions. Minimum input value: 5°.

Cycle parameters
MP6140
hole in the reference axis of the working plane. Input +
range -99999.9999 to 99999.9999 Y Q320
U Center in 2nd axis Q274 (absolute value): Center of

the hole in the minor axis of the working plane. Input
range -99999.9999 to 99999.9999 Q247
U Nominal diameter Q262: Enter the diameter of the Q325
Q262
Q275
Q276
Q274
±Q280
hole. Input range 0 to 99999.9999
U Stepping angle Q247 (incremental): Angle X
between two measuring points. The algebraic sign Q273±Q279
rotation (negative = clockwise). If you wish to
90°. Input range -120.0000 to 120.0000

range -99999.9999 to 99999.9999
Q261
-99999.9999 to 99999.9999, alternatively PREDEF X
measuring points:
points
points
U Maximum limit of size for hole Q275: Maximum
permissible diameter for the hole (circular pocket).
U Minimum limit of size for hole Q276: Minimum
permissible diameter for the hole (circular pocket).
U Tolerance for center 1st axis Q279: Permissible
position deviation in the reference axis of the working
plane. Input range 0 to 99999.9999
U Tolerance for center 2nd axis Q280: Permissible
position deviation in the minor axis of the working

Example: NC blocks

to create a measuring log:
0: No measuring log 5 TCH PROBE 421 MEASURE HOLE
1: Generate measuring log: with the standard setting Q273=+50 ;CENTER IN 1ST AXIS
the TNC saves the log file TCHPR421.TXT in the
directory in which your measuring program is also Q274=+50 ;CENTER IN 2ND AXIS
stored. Q262=75 ;NOMINAL DIAMETER
2: Interrupt the program run and display the
measuring log on the screen. Resume program run Q325=+0 ;STARTING ANGLE
with NC Start. Q247=+60 ;STEPPING ANGLE
U PGM stop if tolerance error Q309: Definition of Q261=-5 ;MEASURING HEIGHT
whether in the event of a violation of tolerance limits
the TNC is to interrupt the program run and output an Q320=0 ;SETUP CLEARANCE
error message: Q260=+20 ;CLEARANCE HEIGHT
0: Do not interrupt program run, no error message
1: Interrupt program run, output an error message Q301=1 ;MOVE TO CLEARANCE
U Tool for monitoring Q330: Definition of whether the Q275=75.12 ;MAX. LIMIT
TNC is to monitor the tool (see “Tool monitoring” on Q276=74.95 ;MIN. LIMIT
page 400). Input range: 0 to 32767.9, alternatively tool
name with max. 16 characters Q279=0.1 ;TOLERANCE 1ST CENTER
0: Monitoring not active Q280=0.1 ;TOLERANCE 2ND CENTER
>0: Tool number in the tool table TOOL.T
Q281=1 ;MEASURING LOG
Q309=0 ;PGM STOP IF ERROR
whether the TNC should measure the stud with 4 or
3 probing points: Q330= ;TOOL
Q423=4 ;NO. OF MEAS. POINTS
3: Use 3 measuring points

16.6 MEAS. CIRCLE OUTSIDE (Cycle 422, DIN/ISO: G422)
16.6 MEAS. CIRCLE OUTSIDE
Cycle run
Touch Probe Cycle 422 measures the center and diameter of a circular
stud. If you define the corresponding tolerance values in the cycle, the
TNC makes a nominal-to-actual value comparison and saves the Y
deviation value in system parameters.
2
TNC calculates the probe starting points from the data in the cycle 3 1
TNC derives the probing direction automatically from the 4
X
parameters:

Q163 Deviation from diameter

calculate the dimensions of the stud. Minimum input
value: 5°

Cycle parameters
stud in the reference axis of the working plane. Input
range -99999.9999 to 99999.9999 Y
stud in the minor axis of the working plane. Input Q247
range -99999.9999 to 99999.9999
U Nominal diameter Q262: Enter the diameter of the Q325
Q278
Q262
Q277
Q274±Q280
stud. Input range 0 to 99999.9999
U Starting angle Q325 (absolute): Angle between the MP6140
reference axis of the working plane and the first touch +
point. Input range -360.0000 to 360.0000 Q320
U Stepping angle Q247 (incremental): Angle X

between two measuring points. The algebraic sign Q273±Q279
rotation (negative = clockwise). If you wish to
90°. Input range -120.0000 to 120.0000

point) in the touch probe axis in which the Z
99999.9999 to 99999.9999
Q260
-99999.9999 to 99999.9999, alternatively PREDEF X
measuring points:
points
points
U Maximum limit of size for stud Q277: Maximum
permissible diameter for the stud. Input range 0 to
99999.9999
U Minimum limit of size for the stud Q278: Minimum
permissible diameter for the stud. Input range 0 to
99999.9999

Example: NC blocks

0: No measuring log 5 TCH PROBE 422 MEAS. CIRCLE OUTSIDE
measuring log on the screen. Resume program run Q325=+90 ;STARTING ANGLE
with NC Start. Q247=+30 ;STEPPING ANGLE
the TNC is to interrupt the program run and output an Q320=0 ;SETUP CLEARANCE
1: Interrupt program run, output an error message Q301=0 ;MOVE TO CLEARANCE
U Tool number for monitoring Q330: Definition of Q275=35.15 ;MAX. LIMIT

whether the TNC is to monitor the tool (see “Tool Q276=34.9 ;MIN. LIMIT
monitoring” on page 400): Input range: 0 to 32767.9,
alternatively tool name with max. 16 characters Q279=0.05 ;TOLERANCE 1ST CENTER
0: Monitoring not active Q280=0.05 ;TOLERANCE 2ND CENTER
whether the TNC should measure the stud with 4 or
3 probing points: Q330= ;TOOL

16.7 MEAS. RECTAN. INSIDE (Cycle 423, DIN/ISO: G423)
16.7 MEAS. RECTAN. INSIDE
Cycle run
Touch Probe Cycle 423 finds the center, length and width of a
rectangular pocket. If you define the corresponding tolerance values in
the cycle, the TNC makes a nominal-to-actual value comparison and
saves the deviation value in system parameters. Y
4
parameters:


axis
Q164 Deviation of side length in reference axis
Q165 Deviation of side length in minor axis


Cycle parameters
pocket in the reference axis of the working plane. Q284
Input range -99999.9999 to 99999.9999 Q282
Y Q285
pocket in the minor axis of the working plane. Input
range -99999.9999 to 99999.9999
U First side length Q282: Pocket length, parallel to
Q287
Q283
Q286
the reference axis of the working plane. Input range 0 Q274±Q280
to 99999.9999
U 2nd side length Q283: Pocket length, parallel to the
99999.9999
X
Q273±Q279
range -99999.9999 to 99999.9999

is added to MP6140. Input range 0 to 99999.9999, Z
how the touch probe is to move between the Q261
measuring points:
points MP6140 X
1: Move at clearance height between measuring +
Q320
points
U Max. size limit 1st side length Q284: Maximum
permissible length of the pocket. Input range 0 to
99999.9999
U Min. size limit 1st side length Q285: Minimum
permissible length of the pocket. Input range 0 to
99999.9999
U Max. size limit 2nd side length Q286: Maximum
permissible width of the pocket. Input range 0 to
99999.9999
U Min. size limit 2nd side length Q287: Minimum
permissible width of the pocket. Input range 0 to
99999.9999

Example: NC blocks

0: No measuring log 5 TCH PROBE 423 MEAS. RECTAN. INSIDE
stored. Q282=80 ;FIRST SIDE LENGTH
measuring log on the screen. Resume program run Q283=60 ;2ND SIDE LENGTH
with NC Start. Q261=-5 ;MEASURING HEIGHT
U PGM stop if tolerance error Q309: Definition of Q320=0 ;SETUP CLEARANCE
the TNC is to interrupt the program run and output an Q260=+10 ;CLEARANCE HEIGHT
error message: Q301=1 ;MOVE TO CLEARANCE
1: Interrupt program run, output an error message Q284=0 ;MAX. LIMIT 1ST SIDE
U Tool number for monitoring Q330: Definition of Q285=0 ;MIN. LIMIT 1ST SIDE
whether the TNC is to monitor the tool (see “Tool Q286=0 ;MAX. LIMIT 2ND SIDE
monitoring” on page 400). Input range: 0 to 32767.9,
alternatively tool name with max. 16 characters Q287=0 ;MIN. LIMIT 2ND SIDE
0: Monitoring not active Q279=0 ;TOLERANCE 1ST CENTER
Q280=0 ;TOLERANCE 2ND CENTER
Q330= ;TOOL

16.8 MEAS. RECTAN. OUTSIDE (Cycle 424, DIN/ISO: G424)
16.8 MEAS. RECTAN. OUTSIDE
Cycle run
Touch Probe Cycle 424 finds the center, length and width of a
rectangular stud. If you define the corresponding tolerance values in
the cycle, the TNC makes a nominal-to-actual value comparison and
saves the deviation value in system parameters. Y
1 Following the positioning logic (see “Executing touch probe 4
1 3
3 Then the touch probe moves either paraxially at the measuring 2
parameters:


axis
Q164 Deviation of side length in reference axis
Q165 Deviation of side length in minor axis


Cycle parameters
stud in the reference axis of the working plane. Input Q284
range -99999.9999 to 99999.9999 Q282
Y
Q285
stud in the minor axis of the working plane. Input
range -99999.9999 to 99999.9999
U First side length Q282: Stud length, parallel to the
Q287
Q283
Q286
reference axis of the working plane. Input range 0 to Q274±Q280
99999.9999
U 2nd side length Q283: Stud length, parallel to the
99999.9999
X
Q273±Q279
range -99999.9999 to 99999.9999

alternatively PREDEF Y
Q285
Q287
Q283
Q286
Q274±Q280
measuring points:
points
1: Move at clearance height between measuring X
points Q273±Q279
U Max. size limit 1st side length Q284: Maximum
permissible length of the stud. Input range 0 to
99999.9999 Z
U Min. size limit 1st side length Q285: Minimum
permissible length of the stud. Input range 0 to
99999.9999
Q260
U Max. size limit 2nd side length Q286: Maximum
permissible width of the stud. Input range 0 to
Q261
99999.9999
U Min. size limit 2nd side length Q287: Minimum
permissible width of the stud. Input range 0 to
99999.9999
MP6140 X
U Tolerance for center 1st axis Q279: Permissible +
position deviation in the reference axis of the working Q320

Example: NC blocks

0: No measuring log 5 TCH PROBE 424 MEAS. RECTAN. OUTS.
stored. Q282=75 ;FIRST SIDE LENGTH
measuring log on the screen. Resume program run Q283=35 ;2ND SIDE LENGTH
U PGM stop if tolerance error Q309: Definition of Q320=0 ;SETUP CLEARANCE
the TNC is to interrupt the program run and output an Q260=+20 ;CLEARANCE HEIGHT
error message: Q301=0 ;MOVE TO CLEARANCE
1: Interrupt program run, output an error message Q284=75.1 ;MAX. LIMIT 1ST SIDE
U Tool number for monitoring Q330: Definition of Q285=74.9 ;MIN. LIMIT 1ST SIDE
whether the TNC is to monitor the tool (see “Tool Q286=35 ;MAX. LIMIT 2ND SIDE
alternatively tool name with max. 16 characters: Q287=34.95 ;MIN. LIMIT 2ND SIDE
0: Monitoring not active Q279=0.1 ;TOLERANCE 1ST CENTER
Q280=0.1 ;TOLERANCE 2ND CENTER
Q330= ;TOOL

16.9 MEASURE INSIDE WIDTH (Cycle 425, DIN/ISO: G425)
16.9 MEASURE INSIDE WIDTH
Cycle run
Touch Probe Cycle 425 measures the position and width of a slot (or
pocket). If you define the corresponding tolerance values in the cycle,
the TNC makes a nominal-to-actual value comparison and saves the
deviation value in a system parameter. Y
2
1
probes the first touch point at the probing feed rate (MP6120). 1.
The first probing is always in the positive direction of the
programmed axis.
3 If you enter an offset for the second measurement, the TNC then X
moves the touch probe (if required, at clearance height) to the next
starting point 2 and probes the second touch point. If the nominal
length is large, the TNC moves the touch probe to the second
touch point at rapid traverse. If you do not enter an offset, the TNC
measures the width in the exact opposite direction.
saves the actual values and the deviation in the following Q
parameters:

Q156 Actual value of measured length
Q166 Deviation of the measured length


Cycle parameters
U Starting point in 1st axis Q328 (absolute): Starting
point for probing in the reference axis of the working Q288
Y
Q289
U Starting point in 2nd axis Q329 (absolute): Starting Q272=2
point for probing in the minor axis of the working
U Offset for 2nd measurement Q310 (incremental):
Distance by which the touch probe is displaced
before the second measurement. If you enter 0,
the TNC does not offset the touch probe. Input Q329
range -99999.9999 to 99999.9999
which the measurement is to be made: X
1:Reference axis = measuring axis Q328 Q272=1
which the measurement is to be made. Input Z
range -99999.9999 to 99999.9999
Q260
U Nominal length Q311: Nominal value of the length to Q261
be measured. Input range 0 to 99999.9999
U Maximum dimension Q288: Maximum permissible
length. Input range 0 to 99999.9999 X
U Minimum dimension Q289: Minimum permissible
length. Input range 0 to 99999.9999

Example: NC blocks
0: No measuring log 5 TCH PROBE 425 MEASURE INSIDE WIDTH
1: Generate measuring log: with the standard setting Q328=+75 ;STARTNG PNT 1ST AXIS
directory in which your measuring program is also Q329=-12.5 ;STARTNG PNT 2ND AXIS
stored. Q310=+0 ;OFFS. 2ND MEASUREMENT
measuring log on the screen. Resume program run Q272=1 ;MEASURING AXIS
U PGM stop if tolerance error Q309: Definition of Q260=+10 ;CLEARANCE HEIGHT
the TNC is to interrupt the program run and output an Q311=25 ;NOMINAL LENGTH
error message: Q288=25.05 ;MAX. LIMIT
1: Interrupt program run, output an error message Q289=25 ;MIN. LIMIT
U Tool number for monitoring Q330: Definition of Q281=1 ;MEASURING LOG

whether the TNC is to monitor the tool (see “Tool Q309=0 ;PGM STOP IF ERROR
monitoring” on page 400): Input range: 0 to 32767.9,
alternatively tool name with max. 16 characters Q330= ;TOOL
0: Monitoring not active Q320=0 ;SETUP CLEARANCE
measuring points:
points
points

16.10 MEASURE RIDGE WIDTH (Cycle 426, DIN/ISO: G426)
16.10 MEASURE RIDGE WIDTH
Cycle run
Touch Probe Cycle 426 measures the position and width of a ridge. If
you define the corresponding tolerance values in the cycle, the TNC
makes a nominal-to-actual value comparison and saves the deviation
value in system parameters. Y
TNC calculates the probe starting points from the data in the cycle 1
probes the first touch point at the probing feed rate (MP6120). 1.
The first probing is always in the negative direction of the
programmed axis.
3 Then the touch probe moves at clearance height to the next X
starting position and probes the second touch point.
saves the actual values and the deviation in the following Q
parameters:

Q156 Actual value of measured length
Q166 Deviation of the measured length

Ensure that the first measurement is always carried out in
the negative direction of the selected measuring axis.
Define Q263 and Q264 correspondingly.

Cycle parameters
Y
99999.9999 Q289
Q272=2
99999.9999 Q264

axis of the working plane. Input range -99999.9999 to MP6140 + Q320
99999.9999
U 2nd meas. point 2nd axis Q266 (absolute): X
Coordinate of the second touch point in the minor axis Q265 Q263 Q272=1
99999.9999
which the measurement is to be made:
1:Reference axis = measuring axis Z
Q260
Q261
range -99999.9999 to 99999.9999
alternatively PREDEF X
U Nominal length Q311: Nominal value of the length to
be measured. Input range 0 to 99999.9999
U Maximum dimension Q288: Maximum permissible
U Minimum dimension Q289: Minimum permissible

Example: NC blocks

0: No measuring log 5 TCH PROBE 426 MEASURE RIDGE WIDTH
1: Generate measuring log: with the standard setting Q263=+50 ;1ST POINT 1ST AXIS
directory in which your measuring program is also Q264=+25 ;1ST POINT 2ND AXIS
stored. Q265=+50 ;2ND POINT 1ST AXIS
measuring log on the screen. Resume program run Q266=+85 ;2ND POINT 2ND AXIS
with NC Start. Q272=2 ;MEASURING AXIS
the TNC is to interrupt the program run and output an Q320=0 ;SET-UP CLEARANCE
1: Interrupt program run, output an error message Q311=45 ;NOMINAL LENGTH
U Tool number for monitoring Q330: Definition of Q288=45 ;MAX. LIMIT

whether the TNC is to monitor the tool (see “Tool Q289=44.95 ;MIN. LIMIT
alternatively tool name with max. 16 characters Q281=1 ;MEASURING LOG
0: Monitoring not active Q309=0 ;PGM STOP IF ERROR
Q330= ;TOOL

16.11 MEASURE COORDINATE (Cycle 427, DIN/ISO: G427)
16.11 MEASURE COORDINATE
Cycle run
Touch probe cycle 427 finds a coordinate in a selectable axis and saves
the value in a system parameter. If you define the corresponding
tolerance values in the cycle, the TNC makes a nominal-to-actual value
comparison and saves the deviation value in system parameters. Z
TNC offsets the touch probe by the safety clearance in the
direction opposite the defined traverse direction.
2 Then the TNC positions the touch probe to the entered touch point
1 in the working plane and measures the actual value in the
selected axis.
3 Finally the TNC returns the touch probe to the clearance height and X
saves the measured coordinate in the following Q parameter:

Q160 Measured coordinate


Cycle parameters
MP6140 + Q320
99999.9999 Y +
Q272=2
99999.9999
Q264
99999.9999 to 99999.9999
X
U Setup clearance Q320 (incremental): Additional Q263 Q272=1
+
U Measuring axis (1..3: 1=reference axis) Q272:
Axis in which the measurement is to be made: Z
1: Reference axis = measuring axis Q272=3 Q267
Q260
U Traverse direction 1 Q267: Direction in which the Q261
probe and workpiece (fixtures) can occur. Input range X
-99999.9999 to 99999.9999, alternatively PREDEF Q272=1

Example: NC blocks
0: No measuring log 5 TCH PROBE 427 MEASURE COORDINATE
1: Generate measuring log: with the standard setting Q263=+35 ;1ST POINT 1ST AXIS
directory in which your measuring program is also Q264=+45 ;1ST POINT 2ND AXIS
stored. Q261=+5 ;MEASURING HEIGHT
measuring log on the screen. Resume program run Q320=0 ;SET-UP CLEARANCE
with NC Start. Q272=3 ;MEASURING AXIS
U Maximum limit of size Q288: Maximum permissible Q267=-1 ;TRAVERSE DIRECTION
measured value. Input range 0 to 99999.9999
U Minimum limit of size Q289: Minimum permissible
measured value. Input range 0 to 99999.9999 Q281=1 ;MEASURING LOG
Q288=5.1 ;MAX. LIMIT
U PGM stop if tolerance error Q309: Definition of
whether in the event of a violation of tolerance limits Q289=4.95 ;MIN. LIMIT
the TNC is to interrupt the program run and output an
error message:
0: Do not interrupt program run, no error message Q330= ;TOOL
1: Interrupt program run, output an error message
U Tool number for monitoring Q330: Definition of
whether the TNC is to monitor the tool (see “Tool
alternatively tool name with max. 16 characters:
0: Monitoring not active

16.12 MEAS. BOLT HOLE CIRC. (Cycle 430, DIN/ISO: G430)
16.12 MEAS. BOLT HOLE CIRC.
Cycle run
Touch Probe Cycle 430 finds the center and diameter of a bolt hole
circle by probing three holes. If you define the corresponding tolerance
values in the cycle, the TNC makes a nominal-to-actual value Y
comparison and saves the deviation value in system parameters.
1
traverse (value from MP6150) to the point entered as center of the 2
first hole 1.
3 The touch probe returns to the clearance height and then to the 3
4 The TNC moves the touch probe to the entered measuring height X
and probes four points to find the second hole center.
position entered as center of the third hole 3.
and probes four points to find the third hole center.
parameters:
Q153 Actual value of bolt hole circle diameter
Q163 Deviation of bolt hole circle diameter

Cycle 430 only monitors for tool breakage, no automatic
tool compensation.

Cycle parameters
U Center in 1st axis Q273 (absolute): Bolt hole circle
center (nominal value) in the reference axis of the
working plane. Input range -99999.9999 to Y Q291
99999.9999
U Center in 2nd axis Q274 (absolute): Bolt hole circle
center (nominal value) in the minor axis of the working
Q292
Q289
Q262
Q288
Q274±Q280
U Nominal diameter Q262: Enter the bolt hole circle
diameter. Input range 0 to 99999.9999
U Angle of 1st hole Q291 (absolute): Polar coordinate
angle of the first hole center in the working plane.
Input range -360.0000 to 360.0000 Q293
X
U Angle of 2nd hole Q292 (absolute): Polar coordinate Q273 ±Q279
angle of the second hole center in the working plane.

Input range -360.0000 to 360.0000
U Angle of 3rd hole Q293 (absolute): Polar coordinate
angle of the third hole center in the working plane.
Input range -360.0000 to 360.0000

range -99999.9999 to 99999.9999
Q260
Q261
U Maximum limit of size Q288: Maximum permissible
diameter of bolt hole circle. Input range 0 to
99999.9999
U Minimum limit of size Q289: Minimum permissible
X
diameter of bolt hole circle. Input range 0 to
99999.9999

Example: NC blocks
0: No measuring log 5 TCH PROBE 430 MEAS. BOLT HOLE CIRC
measuring log on the screen. Resume program run Q291=+0 ;ANGLE OF 1ST HOLE
with NC Start. Q292=+90 ;ANGLE OF 2ND HOLE
U PGM stop if tolerance error Q309: Definition of Q293=+180 ;ANGLE OF 3RD HOLE
the TNC is to interrupt the program run and output an Q261=-5 ;MEASURING HEIGHT
1: Interrupt program run, output an error message Q288=80.1 ;MAX. LIMIT
U Tool number for monitoring Q330: Definition of Q289=79.9 ;MIN. LIMIT

whether the TNC is to monitor for tool breakage (see Q279=0.15 ;TOLERANCE 1ST CENTER
“Tool monitoring” on page 400): Input range: 0 to
32767.9, alternatively tool name with max. 16 Q280=0.15 ;TOLERANCE 2ND CENTER
characters. Q281=1 ;MEASURING LOG
0: Monitoring not active
>0: Tool number in the tool table TOOL.T Q309=0 ;PGM STOP IF ERROR
Q330= ;TOOL

16.13 MEASURE PLANE (Cycle 431, DIN/ISO: G431)
16.13 MEASURE PLANE (Cycle 431,
DIN/ISO: G431)
Cycle run
Touch Probe Cycle 431 finds the angle of a plane by measuring three
points. It saves the measured values in system parameters. +Y
+X
1 Following the positioning logic (see “Executing touch probe Z
traverse (value from MP6150) to the programmed starting point 1
and measures the first touch point of the plane. The TNC offsets
the touch probe by the safety clearance in the direction opposite Y
to the direction of probing. 3
2 The touch probe returns to the clearance height and then moves in
the working plane to starting point 2 and measures the actual value B 2
of the second touch point of the plane. X
1
3 The touch probe returns to the clearance height and then moves in
the working plane to starting point 3 and measures the actual value
of the third touch point. A
saves the measured angle values in the following Q parameters:
Q158 Projection angle of the A axis
Q159 Projection angle of the B axis
Q170 Spatial angle A
Q171 Spatial angle B
Q172 Spatial angle C
Q173 to Q175 Measured values in the touch probe axis

(first to third measurement)


For the TNC to be able to calculate the angular values, the
three measuring points must not be positioned on one
straight line.
The spatial angles that are needed for tilting the working
plane are saved in parameters Q170 – Q172. With the first
two measuring points you also specify the direction of the
reference axis when tilting the working plane.
The third measuring point determines the direction of the
tool axis. Define the third measuring point in the direction
of the positive Y axis to ensure that the position of the tool
axis in a clockwise coordinate system is correct.
If you run the cycle while a tilted working plane is active,
the spatial angle is measured with respect to the tilted
coordinate system. In this case, use the measured spatial
angle with PLANE RELATIV.

Cycle parameters
Coordinate of the first touch point in the reference Y
99999.9999 Y'
the working plane. Input range -99999.9999 to Q297
99999.9999
U 1st meas. point 3rd axis Q294 (absolute):
Coordinate of the first touch point in the touch probe Q266 X'
axis. Input range -99999.9999 to 99999.9999 Q264
U 2nd meas. point 1st axis Q265 (absolute):
axis of the working plane. Input range -99999.9999 to X
Q263 Q296 Q265
99999.9999
U 2nd meas. point 2nd axis Q266 (absolute):
99999.9999 Z
U 2nd meas. point 3rd axis Q295 (absolute): Q260
Coordinate of the second touch point in the touch
probe axis. Input range -99999.9999 to 99999.9999
Q298 MP6140
+
U 3rd meas. point 1st axis Q296 (absolute): Q320
Q295
Coordinate of the third touch point in the reference
99999.9999
U 3rd meas. point 2nd axis Q297 (absolute):
Coordinate of the third touch point in the minor axis of
the working plane. Input range -99999.9999 to X
99999.9999
U 3rd meas. point 3rd axis Q298 (absolute):
Coordinate of the third touch point in the touch probe
axis. Input range -99999.9999 to 99999.9999

Example: NC blocks
is added to MP6140. Input range 0 to 99999.9999, 5 TCH PROBE 431 MEASURE PLANE
alternatively PREDEF Q263=+20 ;1ST POINT 1ST AXIS
U Clearance height Q260 (absolute): Coordinate in the Q264=+20 ;1ST POINT 2ND AXIS
probe and workpiece (fixtures) can occur. Input range Q294=+10 ;1ST POINT 3RD AXIS
-99999.9999 to 99999.9999, alternatively PREDEF Q265=+90 ;2ND POINT 1ST AXIS
U Measuring log Q281: Definition of whether the TNC is Q266=+25 ;2ND POINT 2ND AXIS
0: No measuring log Q295=+15 ;2ND POINT 3RD AXIS
1: Generate measuring log: with the standard setting Q296=+50 ;3RD POINT 1ST AXIS
directory in which your measuring program is also Q297=+80 ;3RD POINT 2ND AXIS
stored. Q298=+20 ;3RD POINT 3RD AXIS
measuring log on the screen. Resume program run Q320=0 ;SET-UP CLEARANCE
with NC Start. Q260=+5 ;CLEARANCE HEIGHT

Example: Measuring and reworking a rectangular stud
Program sequence:
Roughing with 0.5 mm finishing allowance
Measuring Y Y
Rectangular stud finishing in accordance with 80
the measured values
50
60
X Z
50 10
0 BEGIN PGM BEAMS MM

1 TOOL CALL 69 Z Prepare tool call
3 FN 0: Q1 = +81 Pocket length in X (roughing dimension)
4 FN 0: Q2 = +61 Pocket length in Y (roughing dimension)
5 CALL LBL 1 Call subprogram for machining
6 L Z+100 R0 FMAX Retract the tool, change the tool
7 TOOL CALL 99 Z Call the touch probe
8 TCH PROBE 424 MEAS. RECTAN. OUTS. Measure the rough-milled rectangle
Q282=80 ;FIRST SIDE LENGTH Nominal length in X (final dimension)
Q283=60 ;2ND SIDE LENGTH Nominal length in Y (final dimension)
Q284=0 ;MAX. LIMIT 1ST SIDE Input values for tolerance checking not required

Q285=0 ;MIN. LIMIT 1ST SIDE
Q286=0 ;MAX. LIMIT 2ND SIDE
Q287=0 ;MIN. LIMIT 2ND SIDE
Q279=0 ;TOLERANCE 1ST CENTER
Q280=0 ;TOLERANCE 2ND CENTER
Q281=0 ;MEASURING LOG No measuring log transmission
Q309=0 ;PGM STOP IF ERROR Do not output an error message
Q330=0 ;TOOL NUMBER No tool monitoring
9 FN 2: Q1 = +Q1 - +Q164 Calculate length in X including the measured deviation
10 FN 2: Q2 = +Q2 - +Q165 Calculate length in Y including the measured deviation
11 L Z+100 R0 FMAX Retract the touch probe, change the tool
12 TOOL CALL 1 Z S5000 Tool call for finishing
13 CALL LBL 1 Call subprogram for machining
15 LBL 1 Subprogram with fixed cycle for rectangular studs
16 CYCL DEF 213 STUD FINISHING
Q201=-10 ;DEPTH
Q218=Q1 ;FIRST SIDE LENGTH Length in X variable for roughing and finishing
Q219=Q2 ;2ND SIDE LENGTH Length in Y variable for roughing and finishing
Q221=0 ;ALLOWANCE IN 1ST AXS
17 CYCL CALL M3 Cycle call
18 LBL 0 End of subprogram
19 END PGM BEAMS MM

Example: Measuring a rectangular pocket and recording the results
Y Y
90
40
70
X Z
50 -20
-15
0 BEGIN PGM BSMEAS MM

1 TOOL CALL 1 Z Tool call for touch probe
2 L Z+100 R0 FMAX Retract the touch probe
3 TCH PROBE 423 MEAS. RECTAN. INSIDE
Q282=90 ;FIRST SIDE LENGTH Nominal length in X
Q283=70 ;2ND SIDE LENGTH Nominal length in Y

Q284=90.15 ;MAX. LIMIT 1ST SIDE Maximum limit in X
Q285=89.95 ;MIN. LIMIT 1ST SIDE Minimum limit in X
Q286=70.1 ;MAX. LIMIT 2ND SIDE Maximum limit in Y
Q287=69.9 ;MIN. LIMIT 2ND SIDE Minimum limit in Y
Q279=0.15 ;TOLERANCE 1ST CENTER Permissible position deviation in X
Q280=0.1 ;TOLERANCE 2ND CENTER Permissible position deviation in Y
Q281=1 ;MEASURING LOG Save measuring log to a file
Q309=0 ;PGM STOP IF ERROR Do not display an error message in case of a tolerance violation
Q330=0 ;TOOL NUMBER No tool monitoring
5 END PGM BSMEAS MM

Touch Probe Cycles:
Special Functions
17.1 Basics
17.1 Basics
Overview
The TNC provides seven cycles for the following special purposes:
Cycle Soft key Page

2 CALIBRATE TS Radius calibration of Page 447
the touch trigger probe
9 CALIBRATE TS LENGTH Length Page 448

calibration of the touch trigger probe
3 MEASURING Cycle for defining OEM Page 449

cycles
4 MEASURING IN 3-D Measuring cycle Page 451

for 3-D probing for defining OEM cycles
440 MEASURE AXIS SHIFT Page 453
441 FAST PROBING Page 456
460 CALIBRATE TS Radius and length Page 458

calibration on a calibration sphere
446 Touch Probe Cycles: Special Functions

17.2 CALIBRATE TS (Cycle 2)
17.2 CALIBRATE TS (Cycle 2)
Cycle run
Touch probe cycle 2 automatically calibrates a touch trigger probe
using a ring gauge or a precision stud as calibration standard.
the clearance height (but only if the current position is below the
clearance height).
2 Then the TNC positions the touch probe in the working plane to the
center of the ring gauge (calibration from inside) or in its proximity
(calibration from outside).
3 The touch probe then moves to the measuring depth (result of
machine parameters 618x.2 and 6185.x) and probes the ring gauge
successively in X+, Y+, X- and Y-.
4 Finally, the TNC moves the touch probe to the clearance height
and writes the effective radius of the ball tip to the calibration data.
Before you begin calibrating, you must define in Machine

Parameters 6180.0 to 6180.2 the center of the calibrating
workpiece in the working space of the machine (REF
coordinates).
If you are working with several traverse ranges you can
save a separate set of coordinates for the center of each
calibrating workpiece (MP6181.1 to 6181.2 and MP6182.1
to 6182.2).
Cycle parameters
U Clearance height (absolute): Coordinate in the touch Example: NC blocks
probe axis at which the touch probe cannot collide
with the calibration workpiece or any fixtures. Input 5 TCH PROBE 2.0 CALIBRATE TS
range -99999.9999 to 99999.9999 6 TCH PROBE
U Radius of ring gauge: Radius of the calibrating 2.1 HEIGHT: +50 R +25.003 DIRECTION: 0
workpiece. Input range 0 to 99999.9999
U Inside calib. =0/outs. calib.=1: Definition of
whether the TNC is to calibrate from inside or outside:
0: Calibrate from inside
1: Calibrate from outside

17.3 CALIBRATE TS LENGTH (Cycle 9)
17.3 CALIBRATE TS LENGTH
(Cycle 9)
Cycle run
Touch probe cycle 9 automatically calibrates the length of a touch
trigger probe at a point that you determine.
1 Pre-position the touch probe so that the coordinate defined in the
cycle can be accessed without collision.
2 The TNC moves the touch probe in the direction of the negative
tool axis until a trigger signal is released.
3 Finally, the TNC moves the touch probe back to the starting point
of the probing process and writes the effective touch probe length
into the calibration data.
Cycle parameters
U Coordinate of datum (absolute): Exact Example: NC blocks
coordinate of the point that is to be probed. Input
range -99999.9999 to 99999.9999 5 L X-235 Y+356 R0 FMAX
U Reference system? (0=ACT/1=REF): Specify the 6 TCH PROBE 9.0 CALIBRATE TS LENGTH
coordinate system on which the entered datum is to 7 TCH PROBE 9.1 DATUM +50 REFERENCE
be based: SYSTEM 0
0: Entered datum is based on the active workpiece
coordinate system (ACT system)
1: Entered datum is based on the active machine
coordinate system (REF system)

17.4 MEASURING (Cycle 3)
Cycle run
Touch Probe Cycle 3 measures any position on the workpiece in a
selectable direction. Unlike other measuring cycles, Cycle 3 enables
you to enter the measuring path DIST and feed rate F directly. Also, the
touch probe retracts by a definable value after determining the
measured value MB.
1 The touch probe moves from the current position at the entered
feed rate in the defined probing direction. The probing direction
must be defined in the cycle as a polar angle.
2 After the TNC has saved the position, the touch probe stops. The
TNC saves the X, Y, Z coordinates of the probe-tip center in three
successive Q parameters. The TNC does not conduct any length
or radius compensations. You define the number of the first result
parameter in the cycle.
3 Finally, the TNC moves the touch probe back by that value against
the probing direction that you defined in the parameter MB.
The exact behavior of touch probe cycle 3 is defined by

your machine tool builder or a software manufacturer who
uses it within specific touch probe cycles.
The machine parameters 6130 (maximum traverse to

touch point) and 6120 (probing feed rate), which are
effective in other measuring cycles, do not apply in touch
probe cycle 3.
Remember that the TNC always writes to 4 successive Q
parameters.
If the TNC was not able to determine a valid touch point,
the program is run without error message. In this case the
TNC assigns the value –1 to the 4th result parameter so
that you can deal with the error yourself.
The TNC retracts the touch probe by no more than the
retraction distance MB and does not pass the starting point
of the measurement. This rules out any collision during
retraction.
With function FN17: SYSWRITE ID 990 NR 6 you can set
whether the cycle runs through the probe input X12 or
X13.

Cycle parameters
the Q parameter to which you want the TNC to assign
the first measured coordinate (X). The values Y and Z 4 TCH PROBE 3.0 MEASURING
are in the immediately following Q parameters. Input 5 TCH PROBE 3.1 Q1
range 0 to 1999
6 TCH PROBE 3.2 X ANGLE: +15
U Probing axis: Enter the axis in whose direction the
probe is to move and confirm with the ENT key. Input 7 TCH PROBE 3.3 DIST +10 F100 MB1
range: X, Y or Z REFERENCE SYSTEM:0
U Probing angle: Angle, measured from the defined 8 TCH PROBE 3.4 ERRORMODE1
probing axis in which the touch probe is to move.
Confirm with ENT. Input range -180.0000 to 180.0000
U Maximum measuring path: Enter the maximum
distance from the starting point by which the
touch probe is to move. Confirm with ENT. Input
range -99999.9999 to 99999.9999
U Feed rate for measurement: Enter the measuring
feed rate in mm/min. Input range 0 to 3000.000
U Maximum retraction path: Traverse path in the
direction opposite the probing direction, after the
stylus was deflected. The TNC returns the touch
probe to a point no farther than the starting point, so
that there can be no collision. Input range 0 to
99999.9999
U Reference system? (0=ACT/1=REF): Specify whether
the probing direction and the result of measurement
are to be referenced to the actual coordinate system
(ACT, can be shifted or rotated), or to the machine
coordinate system (REF):
0: Probe in the current system and save
measurement result in the ACT system
1: Probe in the machine-based REF system and save
measurement result in the REF system
U Error mode (0=OFF/1=ON): Specify whether the TNC
is to issue an error message if the stylus is deflected
at cycle start. If you select mode 1, the TNC saves the
value 2.0 in the 4th result parameter and continues
the cycle.
0: Issue error message
1: Do not issue error message

17.5 MEASURING IN 3-D (Cycle 4, FCL 3 function)
17.5 MEASURING IN 3-D (Cycle 4,
FCL 3 function)
Cycle run
Cycle 4 is an auxiliary cycle that you can only use in

conjunction with external software! The TNC does not
provide any cycle with which you can calibrate the touch
probe:
Touch probe cycle 4 measures any position on the workpiece in the

probing direction defined by a vector. Unlike other measuring cycles,
Cycle 4 enables you to enter the measuring path and feed rate directly.
Also, the touch probe retracts by a definable value after determining
the measured value.
1 The touch probe moves from the current position at the entered
feed rate in the defined probing direction. Define the probing
direction in the cycle by using a vector (delta values in X, Y and Z).
2 After the TNC has saved the position, the touch probe stops. The
TNC saves the X, Y, Z coordinates of the probe-tip center (without
calculation of the calibration data) in three successive Q
parameters. You define the number of the first parameter in the
cycle.
3 Finally, the TNC moves the touch probe back by that value against
the probing direction that you defined in the parameter MB.
The TNC retracts the touch probe by no more than the

retraction distance MB and does not pass the starting point
of the measurement. This rules out any collision during
retraction.
Ensure during pre-positioning that the TNC moves the
probe-tip center without compensation to the defined
position!
Remember that the TNC always writes to 4 successive Q
parameters. If the TNC could not determine a valid touch
point, the fourth result parameter will have the value –1.
The TNC saves the measured values without calculating
the calibration data of the touch probe.
With function FN17: SYSWRITE ID 990 NR 6 you can set
whether the cycle runs through the probe input X12 or
X13.

17.5 MEASURING IN 3-D (Cycle 4, FCL 3 function)
Cycle parameters
the Q parameter to which you want the TNC to assign
the first coordinate (X). Input range 0 to 1999 5 TCH PROBE 4.0 MEASURING IN 3-D
U Relative measuring path in X: X component of the 6 TCH PROBE 4.1 Q1

direction vector defining the direction in which the 7 TCH PROBE 4.2 IX-0.5 IY-1 IZ-1
touch probe is to move. Input range: -99999.9999 to
99999.9999 8 TCH PROBE
4.3 DIST +45 F100 MB50 REFERENCE SYSTEM:0
U Relative measuring path in Y: Y component of the
direction vector defining the direction in which the
99999.9999
U Relative measuring path in Z: Z component of the
direction vector defining the direction in which the
99999.9999
U Maximum measuring path: Enter the maximum
distance from the starting point by which the touch
probe may move along the direction vector. Input
range: -99999.9999 to 99999.9999
U Feed rate for measurement: Enter the measuring
feed rate in mm/min. Input range 0 to 3000.000
U Maximum retraction path: Traverse path in the
direction opposite the probing direction, after the
stylus was deflected. Input range 0 to 99999.9999
U Reference system? (0=ACT/1=REF): Specify whether
the result of measurement is to be saved in the actual
coordinate system (ACT, can be shifted or rotated), or
with respect to the machine coordinate system (REF).
0: Save the measurement result in the ACT system
1: Save the measurement result in the REF system

17.6 MEASURE AXIS SHIFT (Touch Probe Cycle 440, DIN/ISO: G440)
17.6 MEASURE AXIS SHIFT
(Touch Probe Cycle 440,
DIN/ISO: G440)
Cycle run
Touch probe cycle 440 measures the axis shifts of the machine.
Make sure that the cylindrical calibrating tool used in connection
with the TT 130 has the correct dimensions.
1 The TNC positions the calibrating tool at rapid traverse (value from
MP6550) and following the positioning logic (refer to chapter 1.2)
in the vicinity of the TT.
2 At first the TNC makes a measurement in the touch probe axis.
The calibrating tool is offset by the value you have defined in the
tool table TOOL.T under TT: R-OFFS (standard = tool radius). The
TNC always performs the measurement in the touch probe axis.
3 Then the TNC makes the measurement in the working plane. You
define via parameter Q364 in which axis and in which direction of
the working plane the measurement is to be made.
4 If you make a calibration, the TNC saves the calibration data.
Whenever you make a measurement, the TNC compares the
measured values to the calibration data and writes the deviations
to the following Q parameters:
Q185 Deviation from calibration value in X
Q186 Deviation from calibration value in Y
Q187 Deviation from calibration value in Z
You can use this value for compensating the deviation through an
incremental datum shift (Cycle 7).
5 Finally, the calibrating tool returns to the clearance height.

Before running cycle 440 for the first time, you must have
calibrated the tool touch probe with tool-touch-probe cycle
30.
Ensure that the tool data of the calibrating tool has been
entered in the tool table TOOL.T.
Before running the cycle, you must activate the calibrating
tool with TOOL CALL.
Ensure that the TT tool touch probe is connected to input
X13 of the logic unit and is ready to function (Machine
Parameter 65xx).
Before you perform a measurement, you must have made
at least one calibration, otherwise the TNC will output an
error message. If you are working with several traverse
ranges, you have to make a calibration for each of them.
The TNC calculates incorrect values if the probing
directions for calibrating and measuring do not
correspond.
Each time you run cycle 440, the TNC resets the result
parameters Q185 to Q187.
If you want to set a limit for the axis shift in the machine
axes, enter the desired limits in the tool table TOOL.T
under LTOL for the spindle axis and under RTOL for the
working plane. If the limits are exceeded, the TNC outputs
a corresponding error message after a control
measurement.
After the cycle is completed, the TNC restores the spindle
settings that were active before the cycle (M3/M4).

Cycle parameters
U Operation: 0=calibr., 1=measure? Q363: Specify Example: NC blocks
whether you want to calibrate or make a verification
measurement: 5 TCH PROBE 440 MEASURE AXIS SHIFT
0: Calibrate Q363=1 ;DIRECTION
1: Measure
Q364=0 ;PROBING DIRECTIONS
U Probing directions Q364: Definition of probing
direction(s) in the working plane: Q320=2 ;SET-UP CLEARANCE
0: Measuring only in the positive direction of the Q260=+50 ;CLEARANCE HEIGHT
reference axis
1: Measuring only in the positive direction of the
minor axis
2: Measuring only in the negative direction of the
reference axis
3: Measuring only in the negative direction of the
minor axis
4: Measuring in the positive directions of the
reference axis and the minor axis
5: Measuring in the positive direction of the reference
axis and in the negative direction of the minor axis
6: Measuring in the negative direction of the
reference axis and in the positive direction of the
minor axis
7: Measuring in the negative directions of the
reference axis and the minor axis
distance between measuring point and probe
contact. Q320 is added to MP6540. Input range 0 to
touch probe axis at which no collision between tool
and workpiece (fixtures) can occur (referenced to the
active datum). Input range -99999.9999 to

17.7 FAST PROBING (Cycle 441, DIN/ISO: G441, FCL 2 Function)
17.7 FAST PROBING (Cycle 441,
DIN/ISO: G441, FCL 2 Function)
Cycle run
Touch probe cycle 441 allows the global setting of different touch
probe parameters (e.g. positioning feed rate) for all subsequently used
touch probe cycles. This makes it easy to optimize the programs so
that reductions in total machining time are achieved.
Before programming, note the following

There are no machine movements contained in Cycle 441.
It only sets different probing parameters.
END PGM, M02, M30 resets the global settings of Cycle 441.
You can activate automatic angle tracking (Cycle
Parameter Q399) only if Machine Parameter 6165=1. If you
change Machine Parameter 6165, you must recalibrate
the touch probe.

17.7 FAST PROBING (Cycle 441, DIN/ISO: G441, FCL 2 Function)
Cycle parameters
U Positioning feed rate Q396: Define the feed rate at Example: NC blocks
which the touch probe is moved to the specified
positions. Input range 0 to 99999.9999 5 TCH PROBE 441 FAST PROBING
U Positioning feed rate=FMAX (0/1) Q397: Define Q396=3000 ;POSITIONING FEED RATE
whether the touch probe is to move at FMAX (rapid Q397=0 ;SELECT FEED RATE
traverse) to the specified positions.
0: Move at feed rate from Q396 Q399=1 ;ANGLE TRACKING
1: Move at FMAX Q400=1 ;INTERRUPTION
U Angle tracking Q399: Define whether the TNC is to
orient the touch probe before each probing process.
0: Do not orient
1: Orient the spindle before each probing process to
increase the accuracy
U Automatic interruption Q400: Define whether the
TNC is to interrupt program run and display the
measurement results on the screen after a measuring
cycle for automatic workpiece measurement:
0: Never interrupt the program run, not even if the
output of the measurement results on the screen is
selected in the respective probing cycle.
1: Always interrupt program run and display the
measurement results on the screen. To continue the
program run, press the NC Start button

17.8 CALIBRATE TS (Cycle 460, DIN/ISO: G460)
17.8 CALIBRATE TS (Cycle 460,
DIN/ISO: G460)
Cycle run
With Cycle 460 you can calibrate a triggering 3-D touch probe
automatically on an exact calibration sphere. You can do radius
calibration alone, or radius and length calibration.
1 Clamp the calibration sphere and check for potential collisions.
2 In the touch probe axis, position the touch probe over the
calibration sphere, and in the working plane, approximately over
the sphere center.
3 The first movement in the cycle is in the negative direction of the
touch probe axis.
4 Then the cycle determines the exact center of the sphere in the
touch probe axis.
Before programming, note the following

Pre-position the touch probe in the program so that it is
located approximately above the center of the calibration
sphere.

Cycle parameters
U Exact calibration sphere radius Q407: Enter the Example: NC blocks
exact radius of the calibration sphere used. Input
range 0.0001 to 99.9999 5 TCH PROBE 460 CALIBRATE TS
U Setup clearance Q320 (incremental): Additional Q407=12.5 ;SPHERE RADIUS

distance between measuring point and ball tip. Q320 Q320=0 ;SETUP CLEARANCE
alternatively PREDEF Q301=1 ;MOVE TO CLEARANCE
U Traversing to clearance height Q301: Definition of Q423=4 ;NO. OF PROBE POINTS

how the touch probe is to move between the Q380=+0 ;REFERENCE ANGLE
measuring points:
0: Move at measuring height between measuring Q433=0 ;CALIBRATE LENGTH
points Q434=-2.5 ;DATUM
points
U No. of probe points in plane (4/3) Q423: Specify
whether the TNC should measure the calibration
sphere in the plane with 4 or 3 probing points. 3
probing points increase the measuring speed:
U Reference angle Q380 (absolute): Reference angle
(basic rotation) for measuring the measuring points in
the active workpiece coordinate system. Defining a
reference angle can considerably enlarge the
measuring range of an axis. Input range 0 to 360.0000
U Calibrate length (0/1) Q433: Define whether the
TNC is to calibrate the touch probe length after radius
calibration, as well:
0: Do not calibrate touch probe length
1: Calibrate touch probe length
U Datum for length Q434 (absolute): Coordinate of the
calibration sphere center. The definition is only
required if length calibration is to be carried out. Input
range: -99999.9999 to 99999.9999

460
Touch Probe Cycles: Special Functions
Touch Probe Cycles:
Automatic Kinematics
Measurement
18.1 Kinematic Measurement with TS Touch Probes (Option KinematicsOpt)
18.1 Kinematic Measurement with
TS Touch Probes (Option
KinematicsOpt)
Fundamentals
Accuracy requirements are becoming increasingly stringent,
particularly in the area of 5-axis machining. Complex parts need to be
manufactured with precision and reproducible accuracy even over 3
long periods.
Some of the reasons for inaccuracy in multi-axis machining are
deviations between the kinematic model saved in the control (see
figure 1 at right), and the kinematic conditions actually existing on the
machine (see figure 2 at right). When the rotary axes are positioned, 1
these deviations cause inaccuracy of the workpiece (see figure 3 at 2
right). It is therefore necessary for the model to approach reality as
closely as possible.
The new TNC function KinematicsOpt is an important component
that helps you to really fulfill these complex requirements: A 3-D touch
probe cycle measures the rotary axes on your machine fully
automatically, regardless of whether they are in the form of tables or
spindle heads. A calibration sphere is fixed at any position on the
machine table, and measured with a resolution that you define. During
cycle definition you simply define for each rotary axis the area that you
want to measure.
From the measured values, the TNC calculates the static tilting
accuracy. The software minimizes the positioning error arising from
the tilting movements and, at the end of the measurement process,
automatically saves the machine geometry in the respective machine
constants of the kinematic table.
Overview
The TNC offers cycles that enable you to automatically save, check
and optimize the machine kinematics:
Cycle Soft key Page

450 SAVE KINEMATICS: Automatically Page 464
saving and restoring kinematic
configurations
451 MEASURE KINEMATICS: Page 466

Automatically checking or optimizing the
machine kinematics
452 PRESET COMPENSATION: Page 482

Automatically checking or optimizing the
machine kinematics
462 Touch Probe Cycles: Automatic Kinematics Measurement

18.2 Prerequisites
18.2 Prerequisites
The following are prerequisites for using the KinematicsOpt option:
The software options 48 (KinematicsOpt) and 8 (software option1)
and FCL3 must be enabled.
Software option 52 (KinematicsComp) is necessary for
compensations of angular positions.
The 3-D touch probe used for the measurement must be calibrated.
The cycles can only be carried out with the tool axis Z.
A calibration sphere with an exactly known radius and sufficient
rigidity must be attached to any position on the machine table.
HEIDENHAIN recommends using the calibration spheres KKH 250
(ID number 655 475-01) or KKH 100 (ID number 655 475-02) , which
have particularly high rigidity and are designed especially for
machine calibration. Please contact HEIDENHAIN if you have any
questions in this regard.
The kinematics description of the machine must be complete and
correct. The transformation values must be entered with an
accuracy of approx. 1 mm.
The complete machine geometry must be measured (by the
machine tool builder during commissioning).
Machine parameter MP6600 must define the tolerance limit starting
from which the TNC displays a note when the changes in the
kinematic data exceed this limit value (see “KinematicsOpt:
Tolerance limit in Optimization mode: MP6600” on page 317).
Machine parameter MP6601 must define the maximum permissible
deviation from the entered cycle parameter by the calibration sphere
radius measured in the cycles (see “KinematicsOpt, permissible
deviation of the calibration ball radius: MP6601” on page 317).
The M function number to be used for rotary axis positioning must
be entered in machine parameter MP 6602, or -1 if positioning is to
be done by the NC. An M function must be specially intended for
this application by your machine tool builder.
The KinematicsOpt cycles use the global string

parameters QS0 to QS99. Please note that they may have
changed after execution of these cycles.
If MP 6602 is not equal to -1 you have to position the rotary
axes to 0 degrees (ACTUAL system) before starting one of
the KinematicsOpt cycles (except for 450).

18.3 SAVE KINEMATICS (Cycle 450, DIN/ISO: G450; Option)
18.3 SAVE KINEMATICS (Cycle 450,
DIN/ISO: G450; Option)
Cycle run
With touch probe cycle 450, you can save the active machine
kinematics, restore a previously saved one, or output the current
saving status on the screen and in a log file. There are 10 memory
spaces available (numbers 0 to 9).
Always save the active kinematics configuration before

running a kinematics optimization. Advantage:
You can restore the old data if you are not satisfied with
the results or if errors occur during optimization (e.g.
power failure).
Save mode: In addition to the kinematic configuration, the
TNC always saves the code number (freely definable) last
entered under MOD. Then you cannot overwrite this
memory space unless you enter this code number. If you
have saved a kinematic configuration without a code
number, the TNC automatically overwrites this memory
space during the next saving process!
Restore mode: The TNC can restore saved data only to a
matching kinematic configuration.
Restore mode: Note that a change in the kinematics
always changes the preset as well. Set the preset again if
necessary.

18.3 SAVE KINEMATICS (Cycle 450, DIN/ISO: G450; Option)
Cycle parameters
U Mode (0/1/2) Q410: Specify whether to save or Example: NC blocks
restore a kinematics configuration:
0: Save active kinematics 5 TCH PROBE 450 SAVE KINEMATICS
1: Restore previously saved kinematics configuration Q410=0 ;MODE
2: Display the saving status
Q409=1 ;MEMORY
U Memory (0…9) Q409: Number of the memory space to
which you want to save the entire kinematics
configuration, or the number of the memory space
from which you want to restore it. Input range 0 to 9,
no function if mode 2 is selected.
Log function
After running Cycle 450, the TNC creates a measuring log
(TCHPR450.TXT) containing the following information:
Creation date and time of the log
Path of the NC program from which the cycle was run
Mode used (0=Save/1=Restore/2=Saving status)?
Number of the memory space (0 to 9)
Line number of the kinematics configuration in the kinematic table
Code number, if you entered one immediately before running
Cycle 450.
The other data in the log vary depending on the selected mode:
Mode 0:
Logging of all axis entries and transformation entries of the
kinematics chain that the TNC has saved.
Mode 1:
Logging of all transformation entries before and after restoring the
kinematics configuration
Mode 2:
List with the current saving status on the screen and in the log,
including the number of the memory space, code numbers,
kinematics numbers and date of saving

18.4 MEASURE KINEMATICS (Cycle 451, DIN/ISO: G451; Option)
18.4 MEASURE KINEMATICS
(Cycle 451, DIN/ISO: G451;
Option)
Cycle run
The touch probe cycle 451 enables you to check and, if required,
optimize the kinematics of your machine. Use the 3-D TS touch probe
to measure a HEIDENHAIN calibration sphere that you have attached
to the machine table.
HEIDENHAIN recommends using the calibration spheres

KKH 250 (ID number 655 475-01) or KKH 100 (ID number
655 475-02) , which have particularly high rigidity and are
designed especially for machine calibration. Please
contact HEIDENHAIN if you have any questions in this
regard.
The TNC evaluates the static tilting accuracy. The software minimizes
the spatial error arising from the tilting movements and, at the end of
the measurement process, automatically saves the machine
geometry in the respective machine constants of the kinematics
description.
1 Clamp the calibration sphere and check for potential collisions
2 In the Manual Operation mode, set the datum in the center of the
sphere, or if Q431=1 or Q431=3 is defined: In the touch probe axis,
manually position the touch probe over the calibration sphere , and
in the working plane, over the sphere center.
3 Select the Program Run mode and start the calibration program.

4 The TNC automatically measures all three axes successively in the
resolution you defined.
5 The TNC saves the measured values in the following Q
parameters:
Q141 Standard deviation measured in the A axis
(–1 if axis was not measured)
Q142 Standard deviation measured in the B axis

Q143 Standard deviation measured in the C axis

Q144 Optimized standard deviation in the A axis

(–1 if axis was not optimized)
Q145 Optimized standard deviation in the B axis

Q146 Optimized standard deviation in the C axis


Positioning direction
The positioning direction of the rotary axis to be measured is
determined from the start angle and the end angle that you define in
the cycle. A reference measurement is automatically performed at 0°.
The TNC will issue an error message if the selected start angle, end
angle and number of measuring points result in a measuring position
of 0°.
Specify the start and end angles to ensure that the same position is
not measured twice. As mentioned above, a duplicated point
measurement (e.g. measuring positions +90° and -270°) is not
advisable, however it does not cause an error message.
Example: start angle = +90°, end angle = –90°
Start angle = +90°
End angle = –90°
No. of measuring points = 4
Stepping angle resulting from the calculation = (–90 - +90) / (4-1)
= –60°
Measuring point 1= +90°
Measuring point 3= -30°
Measuring point 4= –90°
Example: start angle = +90°, end angle = +270°
Start angle = +90°
End angle = +270°
No. of measuring points = 4
Stepping angle resulting from the calculation = (270 - 90) / (4-1)
= +60°

Machines with Hirth-coupled axes
In order to be positioned, the axis must move out of the
Hirth coupling. So remember to leave a large enough
safety clearance to prevent any risk of collision between
the touch probe and calibration sphere. Also ensure that
there is enough space to reach the safety clearance
(software limit switch).
Define a retraction height Q408 greater than 0 if software
option 2 (M128, FUNCTION TCPM) is not available.
If necessary, the TNC rounds the calculated measuring
positions so that they fit into the Hirth grid (depending on
the start angle, end angle and number of measuring
points).
Depending on the machine configuration, the TNC cannot
position the rotary axes automatically. If this is the case,
you need a special M function from the machine
manufacturer enabling the TNC to move the rotary axes.
The machine manufacturer must have entered the
number of the M function in machine parameter MP6602
for this purpose.
The measuring positions are calculated from the start angle, end angle
and number of measurements for the respective axis and from the
Hirth grid.
Example calculation of measuring positions for an A axis:

Start angle Q411 = -30
End angle Q412 = +90
Number of measuring points Q414 = 4
Hirth grid = 3°
Calculated stepping angle = ( Q412 - Q411 ) / ( Q414 -1 )
Calculated stepping angle = = ( 90 - -30 ) / ( 4 - 1 ) = 120 / 3 = 40
Measuring position 1 = Q411 + 0 * stepping angle = -30° --> -30°
Measuring position 2 = Q411 + 1 * stepping angle = +10° --> 9°

Choice of number of measuring points
To save time you can make a rough optimization with a small number
of measuring points (1-2).
You then make a fine optimization with a medium number of
measuring points (recommended value = 4). Higher numbers of
measuring points do not usually improve the results. Ideally, you
should distribute the measuring points evenly over the tilting range of
the axis.
This is why you should measure an axis with a tilting range of 0° - 360°
at 3 measuring points at 90°, 180° and 270°.
If you want to check the accuracy accordingly, you can enter a higher
number of measuring points in the Check mode.
You must not define a measuring point at 0° or 360°.

These positions do not provide any metrologically relevant
data and lead to an error message!
Choice of the calibration sphere position on the

machine table
In principle, you can fix the calibration sphere to any accessible
position to the machine table and also on chucking equipment or
workpieces. The following factors can positively influence the result of
measurement:
On machines with rotary tables/tilting tables:
Clamp the calibration sphere as far as possible away from the center
of rotation.
Machines with large traverse:
Clamp the calibration sphere as closely as possible to the position
intended for subsequent machining.

Notes on the accuracy
The geometrical and positioning error of the machine influences the
measured values and therefore also the optimization of a rotary axis.
For this reason there will always be a certain amount of error.
If there were no geometrical and positioning error, any values
measured by the cycle at any point on the machine at a certain time
would be exactly reproducible. The greater the geometrical and
positioning error, the greater is the dispersion of measured results
when you fix the calibration sphere to different positions in the
machine coordinate system.
The dispersion of results recorded by the TNC in the measuring log is
a measure of the machine's static tilting accuracy. However, the
measuring circle radius and the number and position of measuring
points have to be included in the evaluation of accuracy. One
measuring point alone is not enough to calculate dispersion. For only
one point, the result of the calculation is the spatial error of that
measuring point.
If several rotary axes are moved simultaneously, their error values are
combined. In the worst case they are added together.
If your machine is equipped with a controlled spindle, you

should activate the angle tracking using machine
parameter MP6165. This generally increases the accuracy
of measurements with a 3-D touch probe.
If required, deactivate the lock on the rotary axes for the
duration of the calibration. Otherwise it may falsify the
results of measurement. The machine tool manual
provides further information.

Notes on various calibration methods
Rough optimization during commissioning after entering
approximate dimensions.
Number of measuring points between 1 and 2
Angular step of the rotary axes: Approx. 90°
Fine optimization over the entire range of traverse
The start and end angles should cover the largest possible
traverse range of the rotary axes
Position the calibration sphere on the machine table so that on
rotary table axes there is a large measuring circle, or so that on
swivel head axes the measurement can be made at a
representative position (e.g. in the center of the traverse range).
Optimization of a specific rotary axis position
The measurements are made near the rotary axis angle at which
the workpiece is to be machined
Position the calibration sphere on the machine table for calibration
at the position subsequently intended for machining
Inspecting the machine accuracy
Determination of the rotary axis backlash

Backlash
Backlash is a small amount of play between the rotary or angle
encoder and the table that occurs when the traverse direction is
reversed. If the rotary axes have backlash outside of the control loop,
for example because the angle measurement is made with the motor
encoder, this can result in significant error during tilting.
With input parameter Q432, you can activate backlash measurement.
Enter an angle that the TNC uses as traversing angle. The cycle will
then carry out two measurements per rotary axis. If you take over the
angle value 0, the TNC will not measure any backlash.
The TNC does not perform an automatic backlash

compensation.
If the measuring circle radius is < 1 mm, the TNC does not
calculate the backlash. The larger the measuring circle
radius, the more accurately the TNC can determine the
rotary axis backlash (see also ”Log function” on page 479).
Backlash measurement is not possible if machine
parameter MP6602 is set or if the axis is a Hirth axis.

Note that all functions for tilting in the working plane are
reset. M128 or FUNCTION TCPM are deactivated.
Position the calibration sphere on the machine table so
that there can be no collisions during the measuring
process.
Before defining the cycle you must set the datum in the
center of the calibration sphere and activate it, or you
define the input parameter Q431 correspondingly to 1 or 3.
If machine parameter MP6602 is not equal -1 (PLC macro
positions the rotary axes), only start a measurement if all
rotary axes are at 0°.
For the positioning feed rate when moving to the probing
height in the touch probe axis, the TNC uses the value
from cycle parameter Q253 or machine parameter
MP6150, whichever is smaller. The TNC always moves
the rotary axes at positioning feed rate Q253, while the
probe monitoring is inactive.
If the kinematic data attained in the optimize mode are
greater than the permissible limit (MP6600), the TNC
shows a warning. Then you have to confirm acceptance of
the attained value by pressing NC start.
Note that a change in the kinematics always changes the
preset as well. After an optimization, reset the preset.
In every probing process the TNC first measures the
radius of the calibration sphere. If the measured sphere
radius differs from the entered sphere radius by more than
you have defined in machine parameter MP6601, the TNC
shows an error message and ends the measurement.
If you interrupt the cycle during the measurement, the
kinematic data might no longer be in the original condition.
Save the active kinematic configuration before an
optimization with Cycle 450, so that in case of a failure the
most recently active kinematic configuration can be
restored.
Programming in inches: The TNC always records the log
data and results of measurement in millimeters.

Cycle parameters
U Mode (0=Check/1=Measure) Q406: Specify whether Example: Calibration program
the TNC should check or optimize the active
kinematics: 4 TOOL CALL “TASTER“ Z
0: Check the active machine kinematics. The TNC 5 TCH PROBE 450 SAVE KINEMATICS
measures the kinematics in the axes you have
defined, but it does not make any changes to it. The Q410=0 ;MODE
TNC displays the results of measurement in a Q409=5 ;MEMORY
measurement log
1: Optimize the active machine kinematics. The TNC 6 TCH PROBE 451 MEASURE KINEMATICS
measures the kinematics in the rotary axes you have Q406=1 ;MODE
defined and optimizes the position of the rotary
axes of the active kinematics. Q407=12.5 ;SPHERE RADIUS
2: Optimize the active machine kinematics. The TNC Q320=0 ;SETUP CLEARANCE
measures the kinematics in the rotary axes you have
defined and optimizes the position and Q408=0 ;RETR. HEIGHT
compensates the angle of the rotary axes of the Q253=750 ;F PRE-POSITIONING
active kinematics. The KinematicsComp option must
be enabled for Mode 2. Q380=0 ;REFERENCE ANGLE
U Exact calibration sphere radius Q407: Enter the Q411=-90 ;START ANGLE A AXIS
exact radius of the calibration sphere used. Input Q412=+90 ;END ANGLE A AXIS
range 0.0001 to 99.9999
Q413=0 ;INCID. ANGLE A AXIS
distance between measuring point and ball tip. Q320 Q414=0 ;MEAS. POINTS A AXIS
is added to MP6140. Input range 0 to 99999.9999, Q415=-90 ;START ANGLE B AXIS
Q416=+90 ;END ANGLE B AXIS
U Retraction height Q408 (absolute): Input range
Q417=0 ;INCID. ANGLE B AXIS
0.0001 to 99999.9999
Q418=2 ;MEAS. POINTS B AXIS
Input 0:
Do not move to any retraction height. The TNC Q419=-90 ;START ANGLE C AXIS
moves to the next measuring position in the axis to Q420=+90 ;END ANGLE C AXIS
be measured. Not allowed for Hirth axes! The TNC
moves to the first measuring position in the series Q421=0 ;INCID. ANGLE C AXIS
A, then B, then C. Q422=2 ;MEAS. POINTS C AXIS
Input >0:
Retraction height in the untilted workpiece Q423=4 ;NO. OF MEAS. POINTS
coordinate system to which the TNC positions Q431=1 ;PRESET
before a rotary axis positioning in the spindle axis.
Also, the TNC moves the touch probe in the Q432=0 ;BACKLASH, ANG. RANGE
working plane to the datum. The probe monitoring
is not active in this mode. Define the positioning
velocity in parameter Q253.

speed of the tool during positioning in mm/min. Input
range: 0.0001 to 99999.9999; alternatively FMAX,
FAUTO, PREDEF.
U Reference angle Q380 (absolute): Reference angle
reference angle can considerably enlarge the
U Start angle A axis Q411 (absolute): Starting angle in
the A axis at which the first measurement is to be
made. Input range -359.999 to 359.999
U End angle A axis Q412 (absolute): Ending angle in the
A axis at which the last measurement is to be made.
Input range -359.999 to 359.999
U Angle of incid. A axis Q413: Angle of incidence in
the A axis at which the other rotary axes are to be
U Number meas. points A axis Q414: Number of probe
measurements with which the TNC is to measure the
A axis. If input value = 0, the TNC does not measure
the respective axis. Input range 0 to 12
U Start angle B axis Q415 (absolute): Starting angle in
the B axis at which the first measurement is to be
U End angle B axis Q416 (absolute): Ending angle in the
B axis at which the last measurement is to be made.
Input range -359.999 to 359.999
U Angle of incid. in B axis Q417: Angle of incidence
in the B axis at which the other rotary axes are to be
U Number meas. points B axis Q418: Number of probe
B axis. If input value = 0, the TNC does not measure

U Start angle C axis Q419 (absolute): Starting angle in
the C axis at which the first measurement is to be
U End angle C axis Q420 (absolute): Ending angle in the
C axis at which the last measurement is to be made.
Input range -359.999 to 359.999
U Angle of incid. in C axis Q421: Angle of incidence
in the C axis at which the other rotary axes are to be
U Number meas. points C axis Q422: Number of probe
C axis. Input range 0 to 12. If input value = 0, the TNC
does not measure the respective axis.
U Preset (0/1/2/3) Q431: Specify whether the TNC is
to set the active preset (datum) automatically in the
center of the sphere:
0: Do not set the preset automatically in the center of
the sphere: Set the preset manually before the start
of the cycle
1: Set the preset automatically in the center of the
sphere before measurement: Preposition the touch
probe manually over the calibration sphere before the
start of the cycle
sphere after measurement: Set the preset manually
before the start of the cycle
sphere before and after measurement: Preposition
the touch probe manually over the calibration sphere
before the start of the cycle
U Backlash, angle range Q432: Here you define the
angle value to be used as traverse for the
measurement of the rotary axis. The traversing angle
must be significantly larger than the actual backlash
of the rotary axes. If input value = 0, the TNC does not
measure the backlash. Input range: -3.0000 to
+3.0000
If you have activated "Preset" before measurement (Q431

= 1/3), then move the touch probe to a position above the
center of the calibration sphere before the start of the
cycle.

Various modes (Q406)
Test mode Q406 = 0 Example: Angle and position optimization of the
The TNC measures the rotary axes in the positions defined and rotary axes after automatic datum setting
calculates the static accuracy of the tilting transformation.
1 TOOL CALL “TASTER“ Z
The TNC records the results of a possible position optimization
but does not make any adjustments 2 TCH PROBE 451 MEASURE KINEMATICS
Position Optimization mode Q406 = 1 Q406=2 ;MODE

The TNC measures the rotary axes in the positions defined and Q407=12.5 ;SPHERE RADIUS
calculates the static accuracy of the tilting transformation. Q320=0 ;SETUP CLEARANCE
During this, the TNC tries to change the position of the rotary in
Q408=0 ;RETR. HEIGHT
the kinematics model in order to achieve higher accuracy.
The machine data is adjusted automatically Q253=750 ;F PRE-POSITIONING
Position and Angle Optimization mode Q406 = 2 Q380=0 ;REFERENCE ANGLE

The TNC measures the rotary axes in the positions defined and Q411=-90 ;START ANGLE A AXIS
calculates the static accuracy of the tilting transformation. Q412=+90 ;END ANGLE A AXIS
First the TNC tries to optimize the angular position of the rotary
axis by means of compensation (Option #52, KinematicsComp).
If the TNC was able to optimize the angle, it automatically Q414=0 ;MEAS. POINTS A AXIS
optimizes the position in another measurement series. Q415=-90 ;START ANGLE B AXIS
For angle optimization, the machine manufacturer must
have adapted the configuration correspondingly. You can Q417=0 ;INCID. ANGLE B AXIS
ask your machine manufacturer if this is the case, and
whether an angle optimization makes sense. Angle
optimization can be particularly useful on small, compact Q419=+90 ;START ANGLE C AXIS
machines.
Q420=+270 ;END ANGLE C AXIS
Angle compensation is only possible with Option #52 Q421=0 ;INCID. ANGLE C AXIS
KinematicsComp.
Q422=3 ;MEAS. POINTS C AXIS
Q431=1 ;PRESET
Q432=0 ;BACKLASH, ANG. RANGE

Log function
Mode used (0=Check/1=Optimize position/2=Optimize pose)
Active kinematic number
Entered calibration sphere radius
For each measured rotary axis:
Starting angle
End angle
Angle of incidence
Number of measuring points
Dispersion (standard deviation)
Maximum error
Angular error
Ascertained backlash
Averaged positioning error
Measuring circle radius
Compensation values in all axes (preset shift)
Evaluation of measuring points
Measurement uncertainty of rotary axes

Notes on log data
Error outputs
In the Test mode (Q406=0) the TNC outputs the accuracy that can be
attained by optimization and/or the accuracies attained through
optimization (Modes 1 and 2).
If the angular position of a rotary axis was calculated, the measured
data is also shown in the log.
In the log, 'dispersion', a term from statistics, is used as a measure
of accuracy. Measured dispersion (measured standard deviation)
means that 68.3% of the actually measured spatial errors are within
the specified range (+/–). Optimized dispersion (optimized
standard deviation) means that 68.3% of the spatial errors to be
expected after the correction of the kinematics are within the
specified range (+/–).
The valuation numbers are a measure of the quality of the
measuring positions with respect to the changeable transformations
of the kinematics model. The higher the valuation number, the
greater the benefit from optimization by the TNC.
Because the TNC always needs two transformations for measuring

the position of a rotary axis, two valuation numbers per rotary axis
are determined. If a complete valuation is missing, the position of a
rotary axis in the kinematics model is not completely defined. The
higher the valuation number, the greater the benefit from changing
the deviations of the measuring points by adjusting the
transformation. The valuation numbers are independent of the
measured errors. They are defined by the kinematics model, the
position and the number of measuring points per rotary axis.
The valuation of any rotary axis should not fall below a value of 2
Values greater or equal to 4 are desirable.
If the valuation numbers are too small, increase the

measurement range of the rotary axis, or also the number
of measuring points. If these measures do not improve the
valuation number it may be because of an incorrect
kinematic description. If necessary, inform your service
agency.

Measurement uncertainty of angles
The TNC always indicates measurement uncertainty in degrees per 1
µm of system uncertainty. This information is important for evaluating
the quality of the measured positioning errors, or the backlash of a
rotary axis.
The system uncertainty includes at least the repeatability of the axes
(backlash) as well as the positioning uncertainty of the linear axes
(positioning errors) and of the touch probe. Since the TNC does not
know the accuracy of the complete system, you must make a
separate evaluation.
Example of uncertainty of the calculated positioning errors:
Positioning uncertainty of each linear axis: 10 µm
Uncertainty of touch probe: 2 µm
Logged measurement uncertainty: 0.0002 °/µm
System uncertainty = SQRT( 3 * 10² + 2² ) = 17.4 µm
Measurement uncertainty = 0.0002 °/µm * 17.4 µm = 0.0034°
Example of uncertainty of the calculated backlash:
Repeatability of each linear axis: 5 µm
Uncertainty of touch probe: 2 µm
Logged measurement uncertainty: 0.0002 °/µm
System uncertainty = SQRT( 3 * 5² + 2² ) = 8.9 µm
Measurement uncertainty = 0.0002 °/µm * 8.9 µm = 0.0018°

18.5 PRESET COMPENSATION (Cycle 452, DIN/ISO: G452, Option)
18.5 PRESET COMPENSATION
Option)
Cycle run
Touch probe cycle 452 optimizes the kinematic transformation chain
of your machine (see “MEASURE KINEMATICS (Cycle 451, DIN/ISO:
G451; Option)” on page 466). Then the TNC corrects the workpiece
coordinate system in the kinematics model in such a way that the
current preset is in the center of the calibration sphere after
optimization.
This cycle enables you, for example, to adjust different tool changer
heads so that the workpiece preset applies for all heads.
1 Clamp the calibration sphere
2 Measure the complete reference head with Cycle 451, and use
Cycle 451 to finally set the preset in the center of the sphere.
3 Insert the second head
4 Use Cycle 452 to measure the tool changer head up to the point
where the head is changed
5 Use Cycle 452 to adjust other tool changer heads to the reference
head.

If it is possible to leave the calibration sphere clamped to the machine
table during machining, you can compensate for machine drift, for
example. This procedure is also possible on a machine without rotary
axes.
1 Clamp the calibration sphere and check for potential collisions.
2 Set the preset in the calibration sphere.
3 Set the preset on the workpiece, and start machining the
workpiece.
4 Use Cycle 452 for preset compensation at regular intervals. The
TNC measures the drift of the axes involved and compensates it in
the kinematics description.

Q141 Standard deviation measured in the A axis
Q142 Standard deviation measured in the B axis

Q143 Standard deviation measured in the C axis

Q144 Optimized standard deviation in the A axis

Q145 Optimized standard deviation in the B axis

Q146 Optimized standard deviation in the C axis


In order to be able to perform a preset compensation, the

kinematics must be specially prepared. The machine tool
manual provides further information.
Note that all functions for tilting in the working plane are
reset. M128 or FUNCTION TCPM are deactivated.
Position the calibration sphere on the machine table so
that there can be no collisions during the measuring
process.
Before defining the cycle you must set the datum in the
center of the calibration sphere and activate it.
For rotary axes without separate position encoders, select
the measuring points in such a way that you have to
traverse a distance of 1° to the limit switch. The TNC
needs this distance for internal backlash compensation.
For the positioning feed rate when moving to the probing
height in the touch probe axis, the TNC uses the value
from cycle parameter Q253 or machine parameter
MP6150, whichever is smaller. The TNC always moves
the rotary axes at positioning feed rate Q253, while the
probe monitoring is inactive.
If the kinematic data attained in the optimize mode are
greater than the permissible limit (MP6600), the TNC
shows a warning. Then you have to confirm acceptance of
the attained value by pressing NC start.
Note that a change in the kinematics always changes the
preset as well. After an optimization, reset the preset.
In every probing process the TNC first measures the
radius of the calibration sphere. If the measured sphere
radius differs from the entered sphere radius by more than
you have defined in machine parameter MP6601, the TNC
shows an error message and ends the measurement.
If you interrupt the cycle during the measurement, the
kinematic data might no longer be in the original condition.
Save the active kinematic configuration before an
optimization with Cycle 450, so that in case of a failure the
most recently active kinematic configuration can be
restored.
Programming in inches: The TNC always records the log
data and results of measurement in millimeters.

Cycle parameters
U Exact calibration sphere radius Q407: Enter the Example: Calibration program
exact radius of the calibration sphere used. Input
range 0.0001 to 99.9999 4 TOOL CALL “TASTER“ Z
U Setup clearance Q320 (incremental): Additional 5 TCH PROBE 450 SAVE KINEMATICS
distance between measuring point and ball tip. Q320 Q410=0 ;MODE
alternatively PREDEF Q409=5 ;MEMORY
U Retraction height Q408 (absolute): Input range 6 TCH PROBE 452 PRESET COMPENSATION
0.0001 to 99999.9999 Q407=12.5 ;SPHERE RADIUS
Input 0: Q320=0 ;SETUP CLEARANCE
Do not move to any retraction height. The TNC
moves to the next measuring position in the axis to
be measured. Not allowed for Hirth axes! The TNC Q253=750 ;F PRE-POSITIONING
moves to the first measuring position in the series
Q380=0 ;REFERENCE ANGLE
A, then B, then C.
Input >0: Q411=-90 ;START ANGLE A AXIS
Retraction height in the untilted workpiece Q412=+90 ;END ANGLE A AXIS
coordinate system to which the TNC positions
before a rotary axis positioning in the spindle axis. Q413=0 ;INCID. ANGLE A AXIS
Also, the TNC moves the touch probe in the Q414=0 ;MEAS. POINTS A AXIS
working plane to the datum. The probe monitoring
is not active in this mode. Define the positioning Q415=-90 ;START ANGLE B AXIS
velocity in parameter Q253. Q416=+90 ;END ANGLE B AXIS
U Feed rate for pre-positioning Q253: Traversing Q417=0 ;INCID. ANGLE B AXIS
speed of the tool during positioning in mm/min. Input
range: 0.0001 to 99999.9999; alternatively FMAX, Q418=2 ;MEAS. POINTS B AXIS
FAUTO, PREDEF. Q419=-90 ;START ANGLE C AXIS
U Reference angle Q380 (absolute): Reference angle Q420=+90 ;END ANGLE C AXIS
Q421=0 ;INCID. ANGLE C AXIS
reference angle can considerably enlarge the Q422=2 ;MEAS. POINTS C AXIS
U Start angle A axis Q411 (absolute): Starting angle in Q432=0 ;BACKLASH, ANG. RANGE
the A axis at which the first measurement is to be
U End angle A axis Q412 (absolute): Ending angle in the
A axis at which the last measurement is to be made.
Input range -359.999 to 359.999
U Angle of incid. A axis Q413: Angle of incidence in
the A axis at which the other rotary axes are to be
U Number meas. points A axis Q414: Number of probe
A axis. If the input value = 0, the TNC does not
measure the respective axis. Input range 0 to 12
U Start angle B axis Q415 (absolute): Starting angle in
the B axis at which the first measurement is to be

U End angle B axis Q416 (absolute): Ending angle in the
B axis at which the last measurement is to be made.
Input range -359.999 to 359.999
U Angle of incid. in B axis Q417: Angle of incidence
in the B axis at which the other rotary axes are to be
U Number meas. points B axis Q418: Number of probe
B axis. If input value = 0, the TNC does not measure
U Start angle C axis Q419 (absolute): Starting angle in
the C axis at which the first measurement is to be
U End angle C axis Q420 (absolute): Ending angle in the
C axis at which the last measurement is to be made.
Input range -359.999 to 359.999
U Angle of incid. in C axis Q421: Angle of incidence
in the C axis at which the other rotary axes are to be
U Number meas. points C axis Q422: Number of probe
C axis. If input value = 0, the TNC does not measure
U Backlash, angle range Q432: Here you define the
angle value to be used as traverse for the
measurement of the rotary axis. The traversing angle
must be significantly larger than the actual backlash
of the rotary axes. If input value = 0, the TNC does not
measure the backlash. Input range: -3.0000 to
+3.0000

Adjustment of tool changer heads
The goal of this procedure is for the workpiece preset to remain Example: Measuring a reference head
unchanged after changing rotary axes (head exchange).
In the following example, a fork head is adjusted to the A and C axes.
The A axis is changed, whereas the C axis continues being a part of 2 TCH PROBE 451 MEASURE KINEMATICS
the basic configuration. Q406=1 ;MODE
U Insert the tool changer head that will be used as a reference head. Q407=12.5 ;SPHERE RADIUS
U Clamp the calibration sphere. Q320=0 ;SET-UP CLEARANCE
U Insert the touch probe.
U Use Cycle 451 to measure the complete kinematics, including the
reference head. Q253=2000 ;F PRE-POSITIONING
U Set the preset (using Q432 = 2 or 3 in Cycle 451) after measuring Q380=45 ;REFERENCE ANGLE
the reference head Q411=-90 ;START ANGLE A AXIS
Q412=+90 ;END ANGLE A AXIS
Q414=4 ;MEAS. POINTS A AXIS
Q415=-90 ;START ANGLE B AXIS
Q419=+90 ;START ANGLE C AXIS
Q431=3 ;PRESET

Example: Adjusting a tool changer head
U Insert the second tool changer head.
U Measure the head with Cycle 452.
4 TCH PROBE 452 PRESET COMPENSATION
U Measure only the axes that have actually been changed (in this
example: only the A axis; the C axis is hidden with Q422). Q407=12.5 ;SPHERE RADIUS
U The preset and the position of the calibration sphere must not be Q320=0 ;SET-UP CLEARANCE
changed during the complete process.
U All other tool changer heads can be adjusted in the same way.
The head change function can vary depending on the Q380=45 ;REFERENCE ANGLE
individual machine tool. Refer to your machine manual.
Q411=-90 ;START ANGLE A AXIS

Drift Compensation
During machining various machine components are subject to drift Example: Reference measurement for drift
due to varying ambient conditions. If the drift remains sufficiently compensation
constant over the range of traverse, and if the calibration sphere can
be left on the machine table during machining, the drift can be 1 TOOL CALL “TASTER“ Z
measured and compensated with Cycle 452. 2 CYCL DEF 247 DATUM SETTING
U Clamp the calibration sphere. Q339=1 ;DATUM NUMBER
U Insert the touch probe. 3 TCH PROBE 451 MEASURE KINEMATICS
U Measure the complete kinematics with Cycle 451 before starting
the machining process. Q406=1 ;MODE
U Set the preset (using Q432 = 2 or 3 in Cycle 451) after measuring Q407=12.5 ;SPHERE RADIUS
the kinematics. Q320=0 ;SET-UP CLEARANCE
U Then set the presets on your workpieces and start the machining
process.
Q411=+90 ;START ANGLE A AXIS
Q431=3 ;PRESET

Example: Drift compensation
U Measure the drift of the axes at regular intervals.
U Activate the preset in the calibration sphere.
5 TCH PROBE 452 PRESET COMPENSATION
U Use Cycle 452 to measure the kinematics.
U The preset and the position of the calibration sphere must not be Q407=12.5 ;SPHERE RADIUS
changed during the complete process. Q320=0 ;SET-UP CLEARANCE
This procedure can also be performed on machines
without rotary axes. Q253=99999 ;F PRE-POSITIONING
Q411=-90 ;START ANGLE A AXIS

Log function
Active kinematic number
Entered calibration sphere radius
For each measured rotary axis:
Starting angle
End angle
Angle of incidence
Number of measuring points
Maximum error
Angular error
Ascertained backlash
Averaged positioning error
Measuring circle radius
Compensation values in all axes (preset shift)
Measurement uncertainty of rotary axes
Notes on log data

(see “Notes on log data” on page 480)

492
Touch Probe Cycles: Automatic Kinematics Measurement
Touch Probe Cycles:
Automatic Tool
Measurement
19.1 Fundamentals
19.1 Fundamentals
Overview
The TNC and the machine tool must be set up by the

machine tool builder for use of the TT touch probe.
Some cycles and functions may not be provided on your
machine tool. Refer to your machine tool manual.
In conjunction with the TNC’s tool measurement cycles, the tool touch
probe enables you to measure tools automatically. The compensation
values for tool length and radius can be stored in the central tool file
TOOL.T and are accounted for at the end of the touch probe cycle. The
following types of tool measurement are provided:
Tool measurement while the tool is at standstill.
Tool measurement while the tool is rotating.
Measuring individual teeth.
You can program the cycles for tool measurement in the Programming
and Editing mode of operation via the TOUCH PROBE key. The
following cycles are available:
Cycle New format Old format Page

Calibrating the TT, Cycles 30 and 480 Page 499
Calibrating the wireless TT 449, Cycle 484 Page 500
Measuring the tool length, Cycles 31 and 481 Page 501
Measuring the tool radius, Cycles 32 and 482 Page 503
Measuring the tool length and radius, Cycles 33 and 483 Page 505
The measuring cycles can be used only when the central

tool file TOOL.T is active.
Before working with the measuring cycles, you must first
enter all the required data into the central tool file and call
the tool to be measured with TOOL CALL.
You can also measure tools in a tilted working plane.
494 Touch Probe Cycles: Automatic Tool Measurement

19.1 Fundamentals
Differences between Cycles 31 to 33 and
Cycles 481 to 483
The features and the operating sequences are absolutely identical.
There are only two differences between Cycles 31 to 33 and
Cycles 481 to 483:
Cycles 481 to 483 are also available in controls for ISO programming
under G481 to G483.
Instead of a selectable parameter for the status of the
measurement, the new cycles use the fixed parameter Q199.
Setting the machine parameters
The TNC uses the feed rate for probing defined in MP6520
when measuring a tool at standstill.
When measuring a rotating tool, the TNC automatically calculates the

spindle speed and feed rate for probing.
The spindle speed is calculated as follows:
n = MP6570 / (r • 0.0063) where
n Spindle speed [rpm]

MP6570 Maximum permissible cutting speed in m/min
r Active tool radius in mm
The feed rate for probing is calculated from:
v = meas. tolerance • n where
v Feed rate for probing in mm/min

Measuring Measuring tolerance [mm], depending on MP6507
tolerance
n Speed in rpm

19.1 Fundamentals
MP6507 determines the calculation of the probing feed rate:
MP6507=0:
The measuring tolerance remains constant regardless of the tool
radius. With very large tools, however, the feed rate for probing is
reduced to zero. The smaller you set the maximum permissible
rotational speed (MP6570) and the permissible tolerance (MP6510),
the sooner you will encounter this effect.
MP6507=1:
The measuring tolerance is adjusted relative to the size of the tool
radius. This ensures a sufficient feed rate for probing even with large
tool radii. The TNC adjusts the measuring tolerance according to the
following table:
Tool radius Measuring tolerance

Up to 30 mm MP6510
30 to 60 mm 2 • MP6510
60 to 90 mm 3 • MP6510
90 to 120 mm 4 • MP6510
MP6507=2:
The feed rate for probing remains constant, the error of measurement,
however, rises linearly with the increase in tool radius:
Measuring tolerance = (r • MP6510)/ 5 mm), where
r Active tool radius in mm

MP6510 Maximum permissible error of measurement

19.1 Fundamentals
Entries in the tool table TOOL.T
Abbr. Inputs Dialog
CUT Number of teeth (20 teeth maximum) Number of teeth?
LTOL Permissible deviation from tool length L for wear detection. If the Wear tolerance: length?
entered value is exceeded, the TNC locks the tool (status L). Input
range: 0 to 0.9999 mm
RTOL Permissible deviation from tool radius R for wear detection. If the Wear tolerance: radius?
entered value is exceeded, the TNC locks the tool (status I). Input
range: 0 to 0.9999 mm
DIRECT. Cutting direction of the tool for measuring the tool during rotation Cutting direction (M3 = –)?
TT:R-OFFS Tool length measurement: Tool offset between stylus center and Tool offset: radius?
tool center. Preset value: Tool radius R (NO ENT means R).
TT:L-OFFS Radius measurement: tool offset in addition to MP6530 between Tool offset: length?
upper surface of stylus and lower surface of tool. Default: 0
LBREAK Permissible deviation from tool length L for breakage detection. If Breakage tolerance: length?
the entered value is exceeded, the TNC locks the tool (status L).
Input range: 0 to 0.9999 mm
RBREAK Permissible deviation from tool radius R for breakage detection. If Breakage tolerance: radius?
the entered value is exceeded, the TNC locks the tool (status I).
Input range: 0 to 0.9999 mm
Input examples for common tool types

Tool type CUT TT:R-OFFS TT:L-OFFS
Drill – (no function) 0 (no offset required because
tool tip is to be measured)
End mill with diameter of 4 (4 teeth) 0 (no offset required because 0 (no additional offset
< 19 mm tool diameter is smaller than required during radius
the contact plate diameter of measurement. offset from
the TT) MP6530 is used.)
End mill with diameter of 4 (4 teeth) R (offset required because 0 (no additional offset
> 19 mm tool diameter is larger than required during radius
the contact plate diameter of measurement. offset from
the TT) MP6530 is used.)
Radius cutter 4 (4 teeth) 0 (no offset required because 5 (always define the tool
the south pole of the ball is to radius as the offset so that
be measured) the diameter is not
measured in the radius)

19.1 Fundamentals
Display of the measurement results
You can display the results of tool measurement in the additional
status display (in the machine operating modes). The TNC then shows
the program blocks in the left and the measuring results in the right
screen window. The measuring results that exceed the permissible
wear tolerance are marked in the status display with an asterisk “*”;
the results that exceed the permissible breakage tolerance are marked
with the character B.

19.2 Calibrating the TT (Cycle 30 or 480, DIN/ISO: G480)
19.2 Calibrating the TT (Cycle 30 or
480, DIN/ISO: G480)
Cycle run
The TT is calibrated with the measuring cycle TCH PROBE 30 or TCH
PROBE 480 (see also ”Differences between Cycles 31 to 33 and
Cycles 481 to 483” on page 495). The calibration process is automatic.
The TNC also measures the center misalignment of the calibrating tool
automatically by rotating the spindle by 180° after the first half of the
calibration cycle.
The calibrating tool must be a precisely cylindrical part, for example a
cylinder pin. The resulting calibration values are stored in the TNC
memory and are accounted for during subsequent tool measurement.
The calibration tool should have a diameter of more than

15 mm and protrude approx. 50 mm from the chuck. This
constellation causes a deformation of 0.1 µm per 1 N
probing force.
The functioning of the calibration cycle is dependent on

MP 6500. Refer to your Machine Manual.
Before calibrating the touch probe, you must enter the
exact length and radius of the calibrating tool into the tool
table TOOL.T.
The position of the TT within the machine working space
must be defined by setting the Machine Parameters
6580.0 to 6580.2.
If you change the setting of any of the Machine
Parameters 6580.0 to 6580.2, you must recalibrate the TT.
Cycle parameters
U Clearance height: Enter the position in the spindle Example: NC blocks in old format
axis at which there is no danger of collision with the
workpiece or fixtures. The clearance height is 6 TOOL CALL 1 Z
referenced to the active workpiece datum. If you 7 TCH PROBE 30.0 CALIBRATE TT
enter such a small clearance height that the tool tip
would lie below the level of the probe contact, the 8 TCH PROBE 30.1 HEIGHT: +90
TNC automatically positions the calibration tool above
the level of the probe contact (safety zone from Example: NC blocks in new format
MP6540). Input range -99999.9999 to 99999.9999,
alternatively PREDEF 6 TOOL CALL 1 Z
7 TCH PROBE 480 CALIBRATE TT

19.3 CALIBRATING THE WIRELESS TT 449 (Cycle 484, DIN/ISO: G484)
19.3 CALIBRATING THE WIRELESS
TT 449 (Cycle 484, DIN/ISO:
G484)
Fundamentals
With Cycle 484, you calibrate the wireless infrared TT 449 tool touch
probe. The calibration process is not completely automated, because
the TT's position on the table is not defined.
Cycle run
U Insert the calibrating tool.
U Define and start the calibration cycle.
U Position the calibrating tool manually above the center of the touch
probe and follow the instructions in the pop-up window. Ensure that
the calibrating tool is located above the measuring surface of the
probe contact.
The calibration process is semi-automatic. The TNC also measures the
center misalignment of the calibrating tool by rotating the spindle by
180° after the first half of the calibration cycle.
The calibrating tool must be a precisely cylindrical part, for example a
cylinder pin. The resulting calibration values are stored in the TNC
memory and are accounted for during subsequent tool measurement.
The calibration tool should have a diameter of more than

15 mm and protrude approx. 50 mm from the chuck. This
constellation causes a deformation of 0.1 µm per 1 N
probing force.
The functioning of the calibration cycle is dependent on

MP 6500. Refer to your Machine Manual.
Before calibrating the touch probe, you must enter the
exact length and radius of the calibrating tool into the tool
table TOOL.T.
The TT needs to be recalibrated if you change its position
on the table.
Cycle parameters
Cycle 484 has no cycle parameters.

19.4 Measuring the Tool Length (Cycle 31 or 481, DIN/ISO: G481)
19.4 Measuring the Tool Length
(Cycle 31 or 481, DIN/ISO:
G481)
Cycle run
To measure the tool length, program the measuring cycle TCH PROBE
31 or TCH PROBE 481 (see also ”Differences between Cycles 31 to
33 and Cycles 481 to 483” on page 495). Via input parameters you can
measure the length of a tool by three methods:
If the tool diameter is larger than the diameter of the measuring
surface of the TT, you can measure the tool while it is rotating.
If the tool diameter is smaller than the diameter of the measuring
surface of the TT, or if you are measuring the length of a drill or
spherical cutter, you can measure the tool while it is at standstill.
If the tool diameter is larger than the diameter of the measuring
surface of the TT, you can measure the individual teeth of the tool
while it is at standstill.
Cycle for measuring a tool during rotation

The control determines the longest tooth of a rotating tool by
positioning the tool to be measured at an offset to the center of the
touch probe system and then moving it toward the measuring surface
until it contacts the surface. The offset is programmed in the tool table
under Tool offset: Radius (TT: R-OFFS).
Cycle for measuring a tool during standstill (e.g. for drills)

The control positions the tool to be measured over the center of the
measuring surface. It then moves the non-rotating tool toward the
measuring surface of the TT until it touches the surface. To activate
this function, enter zero for the Tool offset: Radius (TT: R-OFFS) in the
tool table.
Cycle for measuring individual teeth

The TNC pre-positions the tool to be measured to a position at the side
of the touch probe head. The distance from the tip of the tool to the
upper edge of the touch probe head is defined in MP6530. You can
enter an additional offset with Tool offset: Length (TT: L-OFFS) in the
tool table. The TNC probes the tool radially during rotation to
determine the starting angle for measuring the individual teeth. It then
measures the length of each tooth by changing the corresponding
angle of spindle orientation. To activate this function, program TCH
PROBE 31 = 1 for CUTTER MEASUREMENT.

19.4 Measuring the Tool Length (Cycle 31 or 481, DIN/ISO: G481)
Before measuring a tool for the first time, enter the

following data on the tool into the tool table TOOL.T: the
approximate radius, the approximate length, the number
of teeth, and the cutting direction.
You can run an individual tooth measurement of tools with
up to 99 teeth. The TNC shows the measured values of up
to 24 teeth in the status display.
Cycle parameters
U Measure tool=0 / Check tool=1: Select whether the Example: Measuring a rotating tool for the first
tool is to be measured for the first time or whether a time; old format
tool that has already been measured is to be
inspected. If the tool is being measured for the first 6 TOOL CALL 12 Z
time, the TNC overwrites the tool length L in the 7 TCH PROBE 31.0 TOOL LENGTH
central tool file TOOL.T by the delta value DL = 0. If
you wish to inspect a tool, the TNC compares the 8 TCH PROBE 31.1 CHECK: 0
measured length with the tool length L that is stored 9 TCH PROBE 31.2 HEIGHT: +120
in TOOL.T. It then calculates the positive or negative
deviation from the stored value and enters it into 10 TCH PROBE 31.3 PROBING THE TEETH: 0
TOOL.T as the delta value DL. The deviation can also
be used for Q parameter Q115. If the delta value is Example: Inspecting a tool and measuring the
greater than the permissible tool length tolerance for individual teeth and saving the status in Q5; old
wear or break detection, the TNC will lock the tool format
(status L in TOOL.T).
6 TOOL CALL 12 Z
U Parameter number for result?: Parameter number in
which the TNC stores the status of the 7 TCH PROBE 31.0 TOOL LENGTH
measurement: 8 TCH PROBE 31.1 CHECK: 1 Q5
0.0: Tool is within the tolerance
1.0: Tool is worn (LTOL exceeded) 9 TCH PROBE 31.2 HEIGHT: +120
2.0:: Tool is broken (LBREAK exceeded). If you do not 10 TCH PROBE 31.3 PROBING THE TEETH: 1
wish to use the result of measurement within the
program, answer the dialog prompt with NO ENT.
Example: NC blocks in new format
U Clearance height: Enter the position in the spindle
axis at which there is no danger of collision with the 6 TOOL CALL 12 Z
workpiece or fixtures. The clearance height is
7 TCH PROBE 481 TOOL LENGTH
referenced to the active workpiece datum. If you
enter such a small clearance height that the tool tip Q340=1 ;CHECK
would lie below the level of the probe contact, the
TNC automatically positions the tool above the level
of the probe contact (safety zone from MP6540). Q341=1 ;PROBING THE TEETH
PREDEF
U Cutter measurement? 0=No / 1=Yes: Choose whether
the control is to measure the individual teeth
(maximum of 99 teeth)

19.5 Measuring the Tool Radius (Cycle 32 or 482, ISO: G482)
19.5 Measuring the Tool Radius
(Cycle 32 or 482, ISO: G482)
Cycle run
To measure the tool radius, program the cycle TCH PROBE 32 or TCH
PROBE 482 (see also ”Differences between Cycles 31 to 33 and
Cycles 481 to 483” on page 495). Via input parameters you can
measure the radius of a tool by two methods:
Measuring the tool while it is rotating.
Measuring the tool while it is rotating and subsequently measuring
the individual teeth.
The TNC pre-positions the tool to be measured to a position at the side
of the touch probe head. The distance from the tip of the milling tool
to the upper edge of the touch probe head is defined in MP6530. The
TNC probes the tool radially while it is rotating. If you have
programmed a subsequent measurement of individual teeth, the
control measures the radius of each tooth with the aid of oriented
spindle stops.

Cylindrical tools with diamond surfaces can be measured
with stationary spindle. To do so, define the number of
teeth (CUT) with 0 and adjust the machine parameter
6500. Refer to your machine tool manual.

19.5 Measuring the Tool Radius (Cycle 32 or 482, ISO: G482)
Cycle parameters
time, the TNC overwrites the tool radius R in the 7 TCH PROBE 32.0 TOOL RADIUS
central tool file TOOL.T by the delta value DR = 0. If
you wish to inspect a tool, the TNC compares the 8 TCH PROBE 32.1 CHECK: 0
measured radius with the tool radius R that is stored 9 TCH PROBE 32.2 HEIGHT: +120
in TOOL.T. It then calculates the positive or negative
deviation from the stored value and enters it into 10 TCH PROBE 32.3 PROBING THE TEETH: 0
TOOL.T as the delta value DR. The deviation can also
be used for Q parameter Q116. If the delta value is Example: Inspecting a tool and measuring the
greater than the permissible tool radius tolerance for individual teeth and saving the status in Q5; old
wear or break detection, the TNC will lock the tool format
(status L in TOOL.T).
6 TOOL CALL 12 Z
which the TNC stores the status of the 7 TCH PROBE 32.0 TOOL RADIUS
1.0: Tool is worn (RTOL exceeded) 9 TCH PROBE 32.2 HEIGHT: +120
2.0: Tool is broken (RBREAK exceeded). If you do not 10 TCH PROBE 32.3 PROBING THE TEETH: 1
wish to use the result of measurement within the
program, answer the dialog prompt with NO ENT.
Example: NC blocks in new format
U Clearance height: Enter the position in the spindle
axis at which there is no danger of collision with the 6 TOOL CALL 12 Z
7 TCH PROBE 482 TOOL RADIUS
referenced to the active workpiece datum. If you
enter such a small clearance height that the tool tip Q340=1 ;CHECK
TNC automatically positions the tool above the level
of the probe contact (safety zone from MP6540). Q341=1 ;PROBING THE TEETH
PREDEF
the control is also to measure the individual teeth

19.6 Measuring Tool Length and
19.6 Measuring Tool Length and Radius (Cycle 33 or 483, ISO: G483)
Radius (Cycle 33 or 483, ISO:
G483)
Cycle run
To measure both the length and radius of a tool, program the
measuring cycle TCH PROBE 33 or TCH PROBE 482 (see also
”Differences between Cycles 31 to 33 and Cycles 481 to 483” on
page 495). This cycle is particularly suitable for the first measurement
of tools, as it saves time when compared with individual
measurement of length and radius. In input parameters you can select
the desired type of measurement:
Measuring the tool while it is rotating.
Measuring the tool while it is rotating and subsequently measuring
the individual teeth.
The TNC measures the tool in a fixed programmed sequence. First it
measures the tool radius, then the tool length. The sequence of
measurement is the same as for measuring cycles 31 and 32.

Cylindrical tools with diamond surfaces can be measured
with stationary spindle. To do so, define the number of
teeth (CUT) with 0 and adjust the machine parameter
6500. Refer to your machine tool manual.

19.6 Measuring Tool Length and Radius (Cycle 33 or 483, ISO: G483)
Cycle parameters
time, the TNC overwrites the tool radius R and the 7 TCH PROBE 33.0 MEASURE TOOL
tool length L in the central tool file TOOL.T by the
delta values DR = 0 and DL = 0. If you wish to inspect 8 TCH PROBE 33.1 CHECK: 0
a tool, the TNC compares the measured data with the 9 TCH PROBE 33.2 HEIGHT: +120
tool data stored in TOOL.T. The TNC calculates the
deviations and enters them as positive or negative 10 TCH PROBE 33.3 PROBING THE TEETH: 0
delta values DR and DL in TOOL.T. The deviations are
also available in the Q parameters Q115 and Q116. If Example: Inspecting a tool and measuring the
the delta values are greater than the permissible tool individual teeth and saving the status in Q5; old
tolerances for wear or break detection, the TNC will format
lock the tool (status L in TOOL.T).
6 TOOL CALL 12 Z
which the TNC stores the status of the 7 TCH PROBE 33.0 MEASURE TOOL
1.0: Tool is worn (LTOL or/and RTOL exceeded) 9 TCH PROBE 33.2 HEIGHT: +120
2.0: Tool is broken (LBREAK or/and RBREAK exceeded). 10 TCH PROBE 33.3 PROBING THE TEETH: 1
If you do not wish to use the result of measurement
within the program, answer the dialog prompt with
NO ENT. Example: NC blocks in new format
U Clearance height: Enter the position in the spindle 6 TOOL CALL 12 Z

axis at which there is no danger of collision with the
7 TCH PROBE 483 MEASURE TOOL
referenced to the active workpiece datum. If you Q340=1 ;CHECK
enter such a small clearance height that the tool tip
TNC automatically positions the tool above the level Q341=1 ;PROBING THE TEETH
of the probe contact (safety zone from MP6540).
PREDEF
the control is also to measure the individual teeth

Index
Symbole C K
3-D touch probes ... 44, 312 Cycles and point tables ... 69 Kinematic measurement ... 462, 466
Calibrating Cylinder surface Accuracy ... 471
Triggering ... 447, 448 Contour machining ... 221 Backlash ... 473
Contour milling ... 230 Calibration methods ... 472, 487,
A Ridge machining ... 227 489
Angle of a plane, measuring ... 437 Slot machining ... 224 Hirth coupling ... 469
Angle, measuring in a plane ... 437 Kinematic measurement ... 466,
Automatic tool measurement ... 497 D 482
Axis-specific scaling ... 288 Datum Kinematics, save ... 464
Save in a datum table ... 344 Log function ... 465, 479, 491
B Save in the preset table ... 344 Measuring points, choice of ... 470
Back boring ... 87 Datum shift Measuring positions, choice
Basic rotation With datum tables ... 275 of ... 470
Measuring during program Within the program ... 274 Prerequisites ... 463
run ... 320 Deepened starting point for Preset compensation ... 482
Setting directly ... 335 drilling ... 94, 99 KinematicsOpt ... 462
Bolt hole circle ... 173 Drilling ... 75, 83, 91
Bolt hole circle, measuring ... 433 Deepened starting point ... 94, 99 M
Bore milling ... 95 Drilling cycles ... 72 Machine parameters for 3-D touch
Boring ... 79 Dwell time ... 303 probes ... 315
Machining patterns ... 58
C E Measurement results in Q
Calibrate touch probe External thread milling ... 132 parameters ... 344, 399
automatically ... 458 Measuring angles ... 405
Centering ... 73 F Mirror image ... 282
Circle, measuring from inside ... 408 Face milling ... 263 Multiple measurements ... 316
Circle, measuring from outside ... 412 Fast probing ... 456
Circular pocket FCL function ... 8 O
Roughing+finishing ... 146 Feature content level ... 8 Oriented spindle stop ... 306
Circular slot Floor finishing ... 198
Roughing+finishing ... 155 P
Circular stud ... 164 G Pattern definition ... 58
Classification of results ... 399 Global settings ... 456 Pecking ... 91, 98
Compensating workpiece misalignment Deepened starting point ... 94, 99
By measuring two points of a H Point pattern
line ... 322 Hard milling ... 205 Circular ... 173
Over two holes ... 325 Helical thread drilling/milling ... 128 Linear ... 176
Over two studs ... 328 Hole, measuring ... 408 Overview ... 172
Via rotary axis ... 331, 336 Point patterns
Confidence range ... 316 Point tables ... 66
Contour cycles ... 182 Positioning logic ... 318
Contour train ... 201 Preset table ... 344
Contour train data ... 203
Coordinate transformation ... 272
Coordinate, measuring a single ... 430
Cycle
Calling ... 50
Defining ... 49

Index P S T
Presetting automatically ... 342 Scaling factor ... 286 Tapping
Center of 4 holes ... 383 Side finishing ... 199 With a floating tap holder ... 107
Center of bolt hole circle ... 377 Single-fluted deep-hole drilling ... 98 With chip breaking ... 112
Center of circular pocket (or SL Cycles Without floating tap holder ... 109,
hole) ... 360 SL cycles 112
Center of circular stud ... 364 Basics ... 182, 249 Thermal expansion, measuring ... 453
Center of rectangular pocket ... 352 Contour data ... 190 Thread drilling/milling ... 124
Center of rectangular stud ... 356 Contour geometry cycle ... 185 Thread milling, fundamentals ... 115
In any axis ... 387 Contour train ... 201 Thread milling, internal ... 117
In inside corner ... 373 Contour train data ... 203 Thread milling/countersinking ... 120
In the touch probe axis ... 381 Floor finishing ... 198 Tilting the working plane ... 290
Outside corner ... 368 Overlapping contours ... 186, 243 Cycle ... 290
Ridge center ... 349 Pilot drilling ... 192 Guide ... 297
Slot center ... 345 Rough-out ... 194 Tolerance monitoring ... 400
Probing feed rate ... 317 Side finishing ... 199 Tool compensation ... 400
Program call SL cycles with complex contour Tool measurement ... 497
Via cycle ... 304 formula ... 238 Calibrating the TT ... 499, 500
SL cycles with simple contour Displaying the measurement
R formula ... 249 results ... 498
Reaming ... 77 Slot milling Machine parameters ... 495
Recording the results of Contour slot ... 205 Measuring tool length and
measurement ... 397 Roughing+finishing ... 150 radius ... 505
Rectangular pocket Slot width, measuring ... 424 Tool length ... 501
Roughing+finishing ... 141 Tool radius ... 503
Rectangular pocket Tool monitoring ... 400
measurement ... 420 Touch probe cycles
Rectangular stud ... 160 Touch probe cycles for automatic
Rectangular stud, measuring ... 416 operation ... 314
Result parameters ... 344, 399 Trochoidal milling ... 205
Ridge, measuring from outside ... 427
Rotation ... 284 U
Rough out: See SL Cycles: Rough-out Universal drilling ... 83, 91
Ruled surface ... 259
Run 3-D data ... 255 W
Width, measuring from inside ... 424
Width, measuring from outside ... 427
Workpiece measurement ... 396
508
Overview
Overview
Fixed cycles
Cycle DEF CALL
Cycle designation Page
number active active
7 Datum shift Page 274
8 Mirror image Page 282
9 Dwell time Page 303
10 Rotation Page 284
11 Scaling factor Page 286
12 Program call Page 304
13 Oriented spindle stop Page 306
14 Contour definition Page 185
19 Tilting the working plane Page 290
20 SL II contour data Page 190
21 SL II pilot drilling Page 192
22 SL II rough out Page 194
23 Floor finishing SL II Page 198
24 Side finishing SL II Page 199
25 Contour train Page 201
26 Axis-specific scaling Page 288
27 Cylinder surface Page 221
28 Cylindrical surface slot Page 224
29 Cylinder surface ridge Page 227
30 Run 3-D data Page 255
32 Tolerance Page 307
39 Cylinder surface external contour Page 230
200 Drilling Page 75
201 Reaming Page 77
202 Boring Page 79
203 Universal drilling Page 83

Overview
Cycle DEF CALL
204 Back boring Page 87
205 Universal pecking Page 91
206 Tapping with a floating tap holder, new Page 107
207 Rigid tapping, new Page 109
208 Bore milling Page 95
209 Tapping with chip breaking Page 112
220 Circular point pattern Page 173
221 Linear point pattern Page 176
230 Multipass milling Page 257
231 Ruled surface Page 259
232 Face milling Page 263
240 Centering Page 73
241 Single-fluted deep-hole drilling Page 98
247 Datum setting Page 281
251 Rectangular pocket (complete machining) Page 141
252 Circular pocket (complete machining) Page 146
253 Slot milling Page 150
254 Circular slot Page 155
256 Rectangular stud (complete machining) Page 160
257 Circular stud (complete machining) Page 164
262 Thread milling Page 117
263 Thread milling/countersinking Page 120
264 Thread drilling/milling Page 124
265 Helical thread drilling/milling Page 128
267 Outside thread milling Page 132
270 Contour train data Page 203
275 Trochoidal slot Page 205
510
Overview
Touch probe cycles
Cycle DEF CALL
0 Reference plane Page 402
1 Polar datum Page 403
2 Calibrate TS radius Page 447
3 Measuring Page 449
4 Measuring in 3-D Page 451
9 Calibrate TS length Page 448
30 Calibrating the TT Page 499
31 Measure/Inspect the tool length Page 501
32 Measure/Inspect the tool radius Page 503
33 Measure/Inspect the tool length and the tool radius Page 505
400 Basic rotation using two points Page 322
401 Basic rotation from two holes Page 325
402 Basic rotation from two studs Page 328
403 Compensate misalignment with rotary axis Page 331
404 Set basic rotation Page 335
405 Compensate misalignment with the C axis Page 336
408 Reference point at slot center (FCL 3 function) Page 345
409 Reference point at ridge center (FCL 3 function) Page 349
410 Datum from inside of rectangle Page 352
411 Datum from outside of rectangle Page 356
412 Datum from inside of circle (hole) Page 360
413 Datum from outside of circle (stud) Page 364
414 Datum from outside of corner Page 368
415 Datum from inside of corner Page 373
416 Datum from circle center Page 377
417 Datum in touch probe axis Page 381
418 Datum at center between four holes Page 383
419 Datum in any one axis Page 387

Overview
Cycle DEF CALL
420 Workpiece—measure angle Page 405
421 Workpiece—measure hole (center and diameter of hole) Page 408
422 Workpiece—measure circle from outside (diameter of circular stud) Page 412
423 Workpiece—measure rectangle from inside Page 416
424 Workpiece—measure rectangle from outside Page 420
425 Workpiece—measure inside width (slot) Page 424
426 Workpiece—measure outside width (ridge) Page 427
427 Workpiece—measure in any selectable axis Page 430
430 Workpiece—measure bolt hole circle Page 433
431 Workpiece—measure plane Page 433
440 Measure axis shift Page 453
441 Rapid probing: Set global touch probe parameters (FCL 2 function) Page 456
450 KinematicsOpt: Save kinematics (option) Page 464
451 KinematicsOpt: Measure kinematics (option) Page 466
452 KinematicsOpt: Preset compensation (option) Page 466
460 Calibrate TS: Radius and length calibration on a calibration sphere Page 458
480 Calibrate the TT Page 499
481 Measure/Inspect the tool length Page 501
482 Measure/Inspect the tool radius Page 503
483 Measure/Inspect the tool length and the tool radius Page 505
484 Calibrate infrared TT Page 500
512
DR. JOHANNES HEIDENHAIN GmbH
Dr.-Johannes-Heidenhain-Straße 5
83301 Traunreut, Germany
{ +49 8669 31-0
| +49 8669 5061
E-mail: [email protected]
Technical support | +49 8669 32-1000
Measuring systems { +49 8669 31-3104
TNC support { +49 8669 31-3101
NC programming { +49 8669 31-3103
PLC programming { +49 8669 31-3102
Lathe controls { +49 8669 31-3105
www.heidenhain.de
3-D Touch Probe Systems from HEIDENHAIN

help you to reduce non-cutting time:
For example in
• workpiece alignment
• datum setting
• workpiece measurement
• digitizing 3-D surfaces
with the workpiece touch probes

TS 220 with cable
TS 640 with infrared transmission
• tool measurement
• wear monitoring
• tool breakage monitoring
with the tool touch probe

TT 140
670 388-21 · Ver01 · SW06 · 3 · 6/2010 · F&W · Printed in Germany

iTNC 530: User's Manual Cycle Programming

Uploaded by

Copyright:

Available Formats

iTNC 530: User's Manual Cycle Programming

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

iTNC 530: User's Manual Cycle Programming

Uploaded by

Copyright:

Available Formats

User’s Manual

This symbol indicates that important information about the

This symbol indicates that there is one or more of the

This symbol indicates that the described function must be

This symbol indicates that you can find detailed

Would you like any changes, or have you found

HEIDENHAIN iTNC 530 3

TNC model NC software number

iTNC 530 E 340 491-06

iTNC 530 340 492-06

iTNC 530 E 340 493-06

iTNC 530 programming station 340 494-06

TNC model NC software number

iTNC 530, HSCI and HeROS 5 606 421-01

smarT.NC user documentation:

HEIDENHAIN iTNC 530 5

Feed rate in mm/min for rotary axes: M116

Circle in 3 axes with tilted working plane

DCM Collision software option

Additional Conversational Language software option

DXF Converter software option

AFC software option

KinematicsOpt software option

3D-ToolComp software option

HEIDENHAIN iTNC 530 7

All upgrade functions are available to you without

Upgrade functions are identified in the manual with FCL n, where n

FCL 4 functions Description

Handwheel superimposition in stopped User’s Manual

3-D basic rotation (set-up Machine manual

FCL 3 functions Description

Touch probe cycles for automatic datum Page 345

Feed-rate reduction for the machining of User’s Manual

PLANE function: Entry of axis angle User’s Manual

User documentation as a User’s Manual

smarT.NC: Programming of smarT.NC User’s Manual

smarT.NC: Contour pocket on point smarT.NC Pilot

smarT.NC: Positioning strategy for smarT.NC Pilot

FCL 2 functions Description

Virtual tool axis User’s Manual

USB support of block devices (memory User’s Manual

Filtering of externally created contours User’s Manual

Possibility of assigning different depths User’s Manual

DHCP dynamic IP-address User’s Manual

Touch-probe cycle for global setting of Page 456

smarT.NC: Graphic support of block smarT.NC Pilot

smarT.NC: Coordinate transformation smarT.NC Pilot

smarT.NC: PLANE function smarT.NC Pilot

Intended place of operation

HEIDENHAIN iTNC 530 9

HEIDENHAIN iTNC 530 11

HEIDENHAIN iTNC 530 13

HEIDENHAIN iTNC 530 15

HEIDENHAIN iTNC 530 17

HEIDENHAIN iTNC 530 19

HEIDENHAIN iTNC 530 21

HEIDENHAIN iTNC 530 23

HEIDENHAIN iTNC 530 25

HEIDENHAIN iTNC 530 27