Formula Sheet for all Wastewater Operator Exams

Revised 8/15

F001
Surface area of a pond, acres = Length, ft x Width, ft
43560

F002
 Surface area, sf   Bottom area, sf   7.48 
Volume of a pond, MG =    Depth, ft    
 2   1,000,000 

F004
 Influent BOD, mg/L  Effluent BOD, mg/L 
BOD removal efficiency, % =   X 100%
 Influent BOD, mg/L 

F008
Theoretical detention time of a pond, days = Volume of the pond, MG
Flow rate, MGD

F011
 Influent concentration  Effluent concentration 
Removal efficiency, % =    100%
 Influent concentration 

F012
Solids, lbs= (Volume, MG) x (MLSS, mg/L) x (8.34)

F016
Average flow rate, MGD = (Final flow, MG) - (Initial flow, MG)
Time elapsed, days

F017
BOD loading, lbs/day = (Flow rate, MGD) x (BOD, mg/L) x 8.34

F018
 Influent TSS  Effluent TSS 
TSS removal efficiency, % =    100%
 Influent TSS 

F020
1200
Volume of sample needed for a BOD test bottle, mL =
EstimatedBOD of the sample,mg/L

F021
BOD, mg/L = (Initial D.O., mg/L - Final D.O., mg/L) x 300 mL
Sample volume, mL

1
F022
Chlorine feed rate, lbs/day = (Flow, MGD) x (Dosage, mg/L) x (8.34)

F023
 Net dry weight, mg 
TSS test results, mg/L =   X 1000 mL/L
 Sample volume, mL 

F030
Pump capacity, gpm = (Width, ft) x (Length, ft) x (Draw-down, ft) x 7.48
Time of draw-down in minutes

F030B
Increased flow = (New pipe diameter, inch)2
(Old pipe diameter, inch) 2

F030C
Flow rate in a pipe, gpd =
 Pipe diameter,inches2 
   0.785  Velocity, ft/sec   60 sec/min 1440 min/day  7.48 gal/cf
 12 in/ft 2 

F032
Desired suspended solids, lbs = (Sludge age, days) x (Primary effluent solids, lb/day)

F033
 0.785  Diameter,inches 2   Stroke, inches  7.48
Volume per stroke, gal/stroke =   
 
2
 12 12

F034
Total dry solids, lbs = (Raw sludge, gal) x (Total solids, %) x (8.34)
100%

F035
MLSS, lbs = (Aeration volume, MG) x (MLSS conc, mg/L) x (8.34)

F037
Digestion time, days = Digester volume, gal
Flow, gpd

F038
 Influent P, mg/L  Effluent P, mg/L 
Phosphorus (P) removal, % =   x 100%
 Influent P, mg/L 
2
F039
Sludge applied, gal = (Area, sf) x (Depth of application, in) x (7.48)
12 in/ft

F040
Pollutant emission rate, lbs/day = (Flow, gpd) x ( Pollutant conc., mg/L) x (3.785 L/gal)
453,600 mg/lb

F043
Chemical application rate, lbs/day = (Flow, MGD) x ( Chemical dosage, mg/L) x 8.34

F045
Flux, gpd/sf =(Flow rate, gpm) x (60 min/hr) x (24 hr/day)
Surface area of membrane, sf

F047
New, or actual, WAS flow rate, MGD = (Calculated WAS flow, MGD) x (24hr/day)
Actual hours of sludge wasting, hr/day

F048
Solids produced, lbs/day = (BOD removed, lbs/day) x (Yield factor)

F050
Primary sludge, lbs/day = (Flow rate, MGD) x (Inflow SS, mg/L - Effluent SS, mg/L) x 8.34

F052
Hydraulic loading of a DAF unit, gpd/sf = (Inflow rate, gpm) x (1440)
Liquid surface area, sf

F053
Solids loading to a centrifuge, lbs/hr = (Sludge flow rate, gal/hr) x (Sludge conc %) x 8.34 lbs/gal
100%

F054
 Influent SS, %  Effluent SS, % 
Efficiency of solids removal, % =   x 100%
 Influent SS, % 

3
F055

Dry polymer, lbs = Volume of solution,gal   Polymer concentration, %   8.34 lb/gal

F058
Pumping rate, gpm = (Volume, cf) x (7.48 gal/cf)
Time, min

F061
Flow, gpd
Surface loading, gpd/sf =
Surface area, sf

F062
Solids loading, lbs/day/sf = (Flow, MGD) x (TSS, mg/L) x (8.34)
Surface area, sf

F063
TSS in aerator, lbs
Sludge age =
TSS in primary effluent, lbs/day

F064
F/M = lbs BOD/day to aeration tank
lbs of MLVSS under aeration

F065
Waste sludge pumping rate, MGD =
 Difference in aerator sludgeinventory, lbs
Current pump rate, MGD   
 RAS concentration, mg/L  8.34 

F066
MLSS in aerationtion tank, lbs
MCRT, days =
TSS wasted,lbs/day  TSS in effluent, lbs/day
F068
BOD Loading from primary, lbs/day
MLVSS, mg/L =
F/M Ratio  Aerator volume, MG   8.34
F069
Return sludge rate, MGD = Settled solids, mL x (Flow, MGD)
(1000 mL - Settled solids, mL)

F073
S02 feed, lbs/day =(Flow, MGD) x (Residual chlorine, mg/L + SO2 overdose, mg/L) x (8.34)

4
F074
Chlorine demand, mg/L = (Chlorine dose, mg/L) - (Chlorine residual, mg/L)

F076
Polymer dose, mg/L = (Polymer delivery rate, gpm) x (Polymer, lbs/gal) x (1,000,000)
(Flow, gpm) x (8.34)

F077
Polymer dose, mg/L = (Polymer feed rate, lbs/day) x (1,000,000)
(Flow, gpm) x (1440) x (8.34)

F078
Volume of seed sludge, gal = (Volume of digester, gal) x (% seed)

F079
Solid loading, lbs/day = (Raw sludge volume,gal)x(Solid conc,%)x(Volatile fraction,%)x(8.34)

F081
Total settleable solids to pump to digester, gpd = (Sludge removed, mL) x (Flow, MGD) x (1000)

F082
% reduction of volatile matter, % = (In - Out) x (100)
In - [(In) x (Out)] (“in” and “out” in fraction, not in %)

F083
 Initial volatile matter, lbs  Final volatile matter, lbs
% reduction of volatile matter, % =    100 %
 Initial volatile matter, lbs 

F087
Seed correction per 1.0 mL of seed = Initial D.O. – Final D.O.
mL of seed in bottle
and
 Initial DO, mg/L  Final DO, mg/L  Seed correction, mg/L
BOD5, mg/L =    300 mL
 Sample volume, mL 

F088
Volume diluted, mL = (Target normality) x (Target volume, mL)
Stock acid normality

F091
Sludge flow, MGD = (Thickener loading, lbs/day/sf) x (Surface area, sf)
(8.34) x (10,000) x (% solids)

F092
Desired lbs of solids in aeration tank = (Daily solids addition, lbs/day) x (Sludge age, days)

5
F094
New digestion time, days = (Digester volume, gal)x(Increase in sludge conc,%-Initial sludge conc,%)
(Initial sludge flow, gpd) x (Initial sludge conc, %)

F096
Volume of working solution, mL = (Beaker volume, mL) x (Dosage, mg/L)
(Stock solution conc, %) x (10,000)

F097
Chemical feed rate, gph = (Flow, MGD) x (Dosage, mg/L) x 100%
(Solution strength, %) x (24 hr/day)

F098
Surface loading rate, gpd/sf = (Flow rate, MGD) x (1,000,000 gal/MG)
(Diameter, ft)2 x (0.785)

F099
Polymer dosage, mg/L = (Polymer pumping rate, gpm) x (Polymer conc. lbs/gal) x (1,000,000)
(Sludge flow rate, gpm) x (8.34 lbs/gal)

F100
Retention % =
Retentate conc., mg/L  Permeate conc., mg/L  100%
Retentate conc., mg/L

F101
Average transmembrane pressure, psi =
(Inlet pressure, psi + Outlet pressure, psi) – Permeate pressure, psi
2

F103
RAS, MGD = (Settled volume, mL/L) x (Influent flow rate, MGD)
(1000 mL/L) - (Settled volume, mL/L)

F105
Sludge age, days =
Tank volume, MG   MLSS, mg/L
Inflowrate, MGD   Primary effluent SS, mg/L
F106
F/M, lb COD/day per lb MLVSS =
Flow, MGD   COD, mg/L  8.34 lbs/gal
Solids under aeration,lbs  Volatile fraction
F108
Phosphorus to be added, lbs/day = [BOD lbs/day x P/BOD (desired ratio)] – (P in wastewater, lbs)

6
F110
Desired COD loading, lbs/day = (COD loading rate, lbs COD/lbs VS) x (VS, lbs)

F111
Sludge produced, lbs/day =
(Flow, MGD) x (Influent BOD, mg/L - Effluent BOD, mg/L) x (8.34 x yield factor)

F112
 Sludge,lbs/day   100% 
Thickened sludge volume, gal/day =     
 8.34 lbs/gal   Sludge solidsconcentration, % 

F114
Solids loading, lbs/hr/sf = (Flow, gpm) x (60) x (8.34 lbs/gal) x (SS%)
(Liquid surface area, sf) x (100%)

F115
Air to solids ratio =
Air supplyrate, cfm  0.075 lb/cf   100%
Solids feed rate, gpm  Sludge conc, %  8.34 lbs/gal
F116
Feed time to a centrifuge, min = (Storage volume, cf) x (Basket sludge conc, %) x (62.4 lbs/cu ft)
(Flow, gpm) x (Influent solids, %) x (8.34 lbs/gal)

F117
Increase of detention time, days =
Aerobic digester volume, gal  Increase in sludgeconc., %
Initial sludgeflow, gpd  Initial sludgeconc., %
F122
Polymer dosage, lbs/ton = (Polymer solution conc, %) x (Polymer added, gpm) x (2,000 lbs/ton)
(Sludge conc, %) x (Sludge flow rate, gpm)

F123
 Recovery, % 
Sludge loading,lbs/day   
Vacuum filter yield, lbs/hr/sq ft =  100% 
Duration of filter operation,hr/day  Filter area, sf 
F124
Required filter run time, hr/day = Sludge solids loading, lbs/day x Solids recovery, %
(Filter yield, lbs/hr/sf) x (Filter area, sf) x (100%)