Scribd
Upload
138 views9 pages

Experiment No. 8: Name of Component / Equipment Specification

This experiment aims to study voltage series and current series feedback amplifiers using BJTs. The document describes the theory of negative feedback amplifiers and the four types. It discusses how voltage series feedback operates as a voltage-controlled system and current series feedback operates as a voltage-current controlled system by converting the current feedback signal to a voltage. The experiment uses Multisim to simulate voltage series and current series amplifier circuits both with and without feedback. Gains are calculated and observed with and without feedback to analyze the effects.

Uploaded by

VINAY YADAV
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
138 views9 pages

Experiment No. 8: Name of Component / Equipment Specification

This experiment aims to study voltage series and current series feedback amplifiers using BJTs. The document describes the theory of negative feedback amplifiers and the four types. It discusses how voltage series feedback operates as a voltage-controlled system and current series feedback operates as a voltage-current controlled system by converting the current feedback signal to a voltage. The experiment uses Multisim to simulate voltage series and current series amplifier circuits both with and without feedback. Gains are calculated and observed with and without feedback to analyze the effects.

Uploaded by

VINAY YADAV
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

EXPERIMENT NO.

8
AIM:
To study Voltage Series and Current Series Feedback Amplifier using BJT.
APPARATUS:
NAME OF COMPONENT / SPECIFICATION
EQUIPMENT
Function Generator Aplab 2MHz waveform generator,
model:MSG2M
DSO Tektronix TBS 1042, two channel
DMM HIOKI DT6212
Resistors 33kΩ, 6.8kΩ, 1.5kΩ, 470Ω, 250kΩ,
(R1, R2, R3, R4) 75kΩ, 5kΩ, 2kΩ
Capacitors 10µF, 10µF
(C1, C2)
Transistor BC 107BP, BC 107BP

SOFTWARE USED: NI Multisim 14.0


THEORY:
A negative-feedback amplifier (or feedback amplifier) is
an electronic amplifier that subtracts a fraction of its output from its input, so
that negative feedback opposes the original signal. An idealized negative-feedback
amplifier as shown in the diagram is a system of three elements:

• An amplifier with gain AOL,


• A feedback network β, which senses the output signal and possibly transforms it in
some way (for example by attenuating or filtering it),
• A summing circuit that acts as a subtractor (the circle in the figure), which
combines the input and the transformed output.
Depending upon these three elements there are four types of feedback
amplifier and we will be studying Voltage Series & Current Series Feedback Amplifier.
It is also known as series current feedback, operates as a voltage-current controlled
feedback system. In the series, current configuration, the feedback error signal is
in series with the input and is proportional to the load current, IOUT. Actually, this type
of feedback converts the current signal into a voltage which is actually fed back and it
is this voltage which is subtracted from the input.
For the series-series connection, the configuration is defined as the output
current, IOUT to the input voltage, VIN. Because the output current, IOUT of the series
connection is fed back as a voltage, this increases both the input and output impedances
of the system. Therefore, the circuit works best as a transconductance amplifier with
the ideal input resistance, RIN being very large, and the ideal output
resistance, ROUT is also very large.
Then the “series-series feedback configuration” functions as transconductance type
amplifier system as the input signal is a voltage and the output signal is a current. Then
for a series-series feedback circuit the transfer gain is given as:
GM = IOUT ÷ VIN

Fig 1: Circuit Diagram of Voltage Series and Current Series


Feedback Amplifier

Fig 2: Current Series Feedback


MULTISIM CIRCUIT: [Voltage Series Circuit without Feedback]

MULTISIM CIRCUIT: [Voltage Series Circuit with Feedback]


MULTISIM CIRCUIT: [Current Series Circuit without Feedback]

MULTISIM CIRCUIT: [Current Series Circuit with Feedback]


SIMULATION: [Voltage Series Circuit with Feedback
SIMULATION: [Voltage Series Circuit without Feedback]
SIMULATION: [Current Series Circuit with Feedback]
SIMULATION: [Current Series Circuit without Feedback]
RESULT:

Calculated Gain –
A = _______dB (with feedback)
A = _______dB (without feedback)
Observed Gain –
A = _______dB (with feedback)
A = _______dB (without feedback)

CONCLUSION:
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________

You might also like