Scribd Logo
Upload

Welcome to Scribd!

  • 24 views

    Clamp Fixing

    Uploaded by

    Stefan Jakovljevic
    This document discusses two methods for fixing glass - clamp fixing and bearing fixing. 1) Clamp fixing uses clamping plates and a screw mechanism to transfer force from the clamp into the glass pane. It allows for an even load distribution across the glass. Intermediate pads are needed between the glass and clamp to account for friction and environmental factors. 2) Bearing fixing inserts a bush between the bolt and drilled glass hole to distribute pressure evenly. The bush material must withstand weathering and be durable. Bearing fixings create a rigid connection between glass elements with no relative movement allowed. Special considerations are needed for laminated glass.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Clamp Fixing

    Uploaded by

    Stefan Jakovljevic
    24 views1 page
    This document discusses two methods for fixing glass - clamp fixing and bearing fixing. 1) Clamp fixing uses clamping plates and a screw mechanism to transfer force from the clamp into the glass pane. It allows for an even load distribution across the glass. Intermediate pads are needed between the glass and clamp to account for friction and environmental factors. 2) Bearing fixing inserts a bush between the bolt and drilled glass hole to distribute pressure evenly. The bush material must withstand weathering and be durable. Bearing fixings create a rigid connection between glass elements with no relative movement allowed. Special considerations are needed for laminated glass.

    Original Description:

    33233

    Original Title

    03

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document discusses two methods for fixing glass - clamp fixing and bearing fixing. 1) Clamp fixing uses clamping plates and a screw mechanism to transfer force from the clamp into the glass pane. It allows for an even load distribution across the glass. Intermediate pads are needed between the glass and clamp to account for friction and environmental factors. 2) Bearing fixing inserts a bush between the bolt and drilled glass hole to distribute pressure evenly. The bush material must withstand weathering and be durable. Bearing fixings create a rigid connection between glass elements with no relative movement allowed. Special considerations are needed for laminated glass.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    24 views1 page

    Clamp Fixing

    Uploaded by

    Stefan Jakovljevic
    This document discusses two methods for fixing glass - clamp fixing and bearing fixing. 1) Clamp fixing uses clamping plates and a screw mechanism to transfer force from the clamp into the glass pane. It allows for an even load distribution across the glass. Intermediate pads are needed between the glass and clamp to account for friction and environmental factors. 2) Bearing fixing inserts a bush between the bolt and drilled glass hole to distribute pressure evenly. The bush material must withstand weathering and be durable. Bearing fixings create a rigid connection between glass elements with no relative movement allowed. Special considerations are needed for laminated glass.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Construction details

    Clamp fixing

    3.1.25 Glass suspended with clamping plates 2

    Vertical section and elevation 2


    scale 1:5

    3
    3
    For frameless glazing it is often more sensible
    to design the glass as a suspended system
    (curtain wall) – instead of supporting it from
    underneath – to rule out stability problems. 5 4
    4
    However, this can be achieved only by using
    elaborate and expensive connections. The
    clamp fixing shown here was specifically 1
    devised for fixing single glazing. A screw
    mechanism transfers the clamping force into
    the pane of glass, which can accommodate the
    weight of the glass, depending on the coeffi- pads and environmental conditions (moisture,
    cient of friction of the intermediate pad temperature, soiling etc.) must be taken into
    between glass and clamping jaws. In principle, consideration. Fig. 3.1.35 shows an even and
    clamp fixings are a suitable means of jointing statically determinate load transfer through an 1 Glass 6
    for glass because in contrast to point fixings, articulated joint and correspondingly long 2 Articulated joint
    the loads can be transferred evenly into the clamping pieces. The bottom edges of the 3 Clamping section
    glass and essentially avoid any concentrations panes must remain free to move. They are 4 Clamping jaws
    5 Intermediate pad
    of stress. On the practical side, boundary con- therefore sealed in grooved gaskets in such a as friction surface
    ditions such as the surface finish of the friction way that structural movement or deflections in 6 Permanently elastic
    faces, the creep characteristics of intermediate the floor slab can be compensated for. joint
    3.1.25

    Bearing fixing

    3.1.26 Rigid connection via bearing in drilled


    hole
    3.1.27 Glass fin

    Elevations and horizontal sections


    scale 1:5

    Bearing fixings have proved useful in steel and


    timber engineering. They are characterized by 2 1 2
    their simple and robust handling, which makes
    them ideal for the conditions on a building site. 3
    However, in the case of glass, in contrast to
    structural steelwork, we cannot assume a uni-
    form distribution of the bearing pressure on the 1
    sides of the hole. In order to distribute the pres- 1 4
    sure as evenly as possible over the sides of a
    hole drilled through glass, a bush must be
    inserted between bolt and glass to dissipate
    the stress peaks. The bushes are made from
    special aluminium alloys or synthetic materials
    (Teflon, polyamide), or are injected materials
    such as epoxy, polyester or polyurethane, and
    must be durable, able to withstand the rigours
    of the weather. The long-term suitability of bush 5 6 3.1.26
    materials must be verified beforehand by way resulting properties must be taken into account
    of tests. No relative movements between the when calculating the stresses in the glass, and 1 Glass 4 6
    glass elements can be permitted in connec- if an expansion joint is required, it must be 2 Bolt with locknut
    tions designed to transfer forces. The bolted incorporated at another place, not here. In the 3 Steel splice plate
    4 Intermediate pad
    connections shown in figs 3.1.26 and 3.1.27 case of laminated glass and laminated safety 5 Washer
    function as though the individual glass compo- glass, the flow properties of the interlayer must 6 Sleeve made from
    nents were one piece. This is a rigid joint. The be taken into account. injected material
    3.1.27

    169

    You might also like