TWO PIECE KELLY VALVES

OPERATION AND MAINTENANCE PROCEDURE REV 2 –

01/2012

ASSEMBLY PROCEDURE FOR THE TWO PIECE 3.9 Insert wave Spring into the Sub.
KELLY VALVES
3.10 Insert Seat into the Sub with radial
1.0 SCOPE surface toward Ball.
1.1 This procedure will provide general
instructions regarding assembling the 3.11 Use operating wrench to turn ball to the
Two Piece Kelly valves with the IDs: half open position.
• 2”
• 2-7/16” 3.12 Apply suitable thread dope to the middle
• 2-3/4” connection of Sub and Body.
• 3-1/4”
3.13 Recommended: Dope base to include
40% to 60% (by weight) finely powdered
2.0 REFERENCES
zinc or lead.
2.1 The latest revision of the following
3.14 Screw Upper Sub into the Lower Sub.
specifications may be used to obtain
Make-up shoulders by hand with chain
additional information regarding this
tongs or equivalent.
procedure.
3.15 Torque Lower Sub to Upper Sub:
• Packard Quality Procedures Manual.
• API Specification 7-1 latest edition. • For Standard / H2S Trim Service:
• Bill of materials. Middle Connection
ID OD TORQUE IN FT/LBS
3.0 ASSEMBLY PROCEDURE
+500 / -0
4.5” 7,500
3.1 Clean valve body & sub and all internal 2”
parts. 5” 16,960
2-7/16” 4-7/8 9,800
3.2 Visually Inspect for sign of damage or 6-3/8” 33,350
2-3/4”
wear. 6-3/4” 41500
6-3/4” 26,250
3.3 If a stem with one ear is used on the 7-1/2” 54,500
3-1/4”
valve, discard it and use the new style 7-3/4” 61,750
two ears stem with the supplied stop ring 8-1/2” 83,700
Note: there is no need for the stop ring This is a generic table for products with Standard
To be installed if the valve was delivered API service connections. Request make-up torque
with the new stem style installed in the value information from Packard when the valve has
body. Proprietary high torque service connections.

3.4 Fit Operator (stem), both Seats and Sub

with new O rings. O ring elastomer must 4.0 HYDROSTATIC TEST VALVE
be compatible with drilling environment.
Seats should include new Teflon seal. 4.1 Testing shall be performed in
accordance with the test pressure and
3.5 If needed (refer to 3.3) insert the stop procedures outlined in API Specification
ring into the body until it is fully seated in 7-1 latest edition.
the ball pocket against the shoulder. Table 1.1

3.6 Insert Seat into the Body. The Ball will HYDROSTATIC TESTING PRESSURES
ride on radial surface of Seat.
MAXIMUM WORKING MAXIMUM HYDROSTATIC
3.7 Insert Operator (stem). The V mark on PRESSURE RATING SHELL TEST PRESSURE
the stem should be towards the close psi MPa psi MPa
mark on the valve, representing closed 5000 34.5 10,000 68.9
position of Ball. 10,000 68.9 15,000 103.4
15,000 103.4 22,500 155.1
3.8 Insert Ball in closed position. Note: test pressure shall be stabilized prior to the
timing start for holding pressure

22397 White Oak Drive • Conroe, Texas 77306-8859 • Tel: 281-399-8771 • Fax: 281-399-8773 • www.packardusa.com
1/5
 TWO PIECE KELLY VALVES
OPERATION AND MAINTENANCE PROCEDURE REV 2 –
01/2012

4.12 With the wrench turn the Kelly valve to

the closed position.
SHELL Test (new valves only not required in the
field):

4.2 Install the test plug and cap on both box

and pin connections of the valve 4.12.1 Engage pump and increase the
assembly to be tested. pressure to 250 psi and
stabilize. After stabilization of
4.3 Install the pressure line to the bottom pressure, the valve will be held
(Pin) connection of the valve (test cap). at pressure for five (5) minutes
minimum with no detectable
4.4 With bleed valve on the top of the test pressure drop or leakage.
plug (box connection of the valve) in the
open position, fill the body with water 4.12.2 At the elapse of five minutes,
until it bleeds through the open bleed the pressure will be reduced to
valve. Actuate the valve several times zero.
to eliminate any trapped air in the valve
body. 4.12.3 Engage pump a second time to
increase the pressure to the
4.5 Close the bleed valve. Working Pressure per Table
1.1 and hold for a minimum of
4.6 With the wrench turn the Kelly valve to 5 minutes.
the half-open position.
4.13 Release the pressure on the assembly.
4.6.1 Engage pump and increase ______________________________________________
pressure to 250 psi and stabilize. After
stabilization of pressure, the valve will
be held at pressure for three (3) minutes
minimum with no detectable pressure
drop.

4.6.2 At the elapse of three minutes,

the pressure will be reduced to zero.

4.6.3 Engage pump a second time to

increase the pressure 250 psi and hold
for a minimum of 10 minutes.

4.7 Repeat 4.6.1 to 4.6.3 at the Shell Test

pressure per Table 1.1.

4.8 Release pressure on the assembly

Seat Test :

4.9 Install the test cap on the pin connection

of the valve assembly to be tested.

4.10 Install the pressure line to the bottom of

the cap

4.11 Fill up the body with water until all the

internals are submerged. Actuate the
valve several times to eliminate any
trapped air in the valve body.

22397 White Oak Drive • Conroe, Texas 77306-8859 • Tel: 281-399-8771 • Fax: 281-399-8773 • www.packardusa.com
2/5
 TWO PIECE KELLY VALVES
OPERATION AND MAINTENANCE PROCEDURE REV 2 –
01/2012

PREPARING THE TWO PIECE LOWER KELLY VALVE

DISASSEMBLY PROCEDURE FOR THE TWO PIECE FOR INSTALLATION
KELLY VALVE
1.0 SCOPE
1.0 SCOPE
1.1. This procedure will provide general instructions
1.1. This procedure will provide general instructions regarding installation of the Two Piece Kelly
regarding disassembly of the Two Piece Kelly Valve.
Valve.
2.0 REFERENCES
2.0 REFERENCES
2.1. The latest revision of the following specifications
2.1. The latest revision of the following specifications may be used to obtain additional information
may be used to obtain additional information regarding this procedure.
regarding this procedure.
• Packard Quality Procedures Manual.
• Packard Quality Procedures Manual. • API Specification 7-1 latest edition.
• API Specification 7-1 latest edition. • Bill of materials.
• Bill of materials.
3.0 INSTALLATION PROCEDURE
3.0 DISASSEMBLY PROCEDURE
3.1. Clean shipping thread dope from threaded
3.1. Break Lower Sub from Upper Sub. connections and apply thread dope suitable for
drill string use.
3.2. Unscrew Upper Sub from Lower Sub.
3.2. Recommended: Dope base to include 40% to
3.3. Remove all internal parts. Ball will need to be in 60% (by weight) finely powdered zinc or lead.
closed position.

Thoroughly clean all parts and valve body. Used parts

should be inspected prior to re-use. All Elastomers should
be discarded and replaced regardless of their condition

22397 White Oak Drive • Conroe, Texas 77306-8859 • Tel: 281-399-8771 • Fax: 281-399-8773 • www.packardusa.com
3/5
 TWO PIECE KELLY VALVES
OPERATION AND MAINTENANCE PROCEDURE REV 2 –
01/2012

MAINTENANCE
3.4 How the valve is used and the
1.0 SCOPE frequency of maintenance become the
priority in ensuring long operating life.
1.1 This procedure will provide general The valve should be operated at
instructions regarding the maintenance balanced pressure. If the valve is closed
of the two Piece Kelly Valve when the mud pumps are started and it
is opened with pressure from above, the
2.0 REFERENCES operating life will be shortened.

2.1 The latest revision of the following

specifications may be used to obtain 3.5 If the valve is used for twelve weeks,
additional information regarding this and it still operates smoothly, it should
procedure. be removed from service and the basic
maintenance routine should be
• ISO 10424-1 latest edition. performed. If, at the twelve week
• Bill of materials. interval, it does not still operate
smoothly, the interval should be
3.0 MAINTENANCE SCHEDULING shortened to nine weeks. At nine weeks,
if it is still operating smoothly, the
interval should remain nine weeks. If it
3.1 If the pressure test fails or the valve is not operating smoothly, the interval
becomes difficult to operate, remove the should be shortened to six weeks.
valve from service immediately,
disassemble, clean thoroughly, inspect,
4.0 REPAIR AND SEAL KIT USAGE ORDER
replace worn parts, reassemble, and
test.
4.1 Repair kits include a ball, 2 seats,
spring, stem, stop ring and a seal kit.
3.2 Depending upon the drilling factors of
pressure, mud weight /composition
4.2 Seal kits include all elastomers
/contamination, rate of penetration,
hook load, the frequency of
4.3 At each maintenance interval the types
maintenance will vary.
of kits should be alternated: seal kit,
then repair kit, then seal kit, then repair
3.3 In conjunction with the frequency of kit, and so on, unless the ball, seats or
maintenance, how the maintenance is stem are damaged, in that case, a
performed is critical. Basic maintenance repair kit must be used.
should be performed not in response to
a failure; it should be performed to avoid 5.0 MAINTENANCE ROUTINE
a failure. Drilling mud can become
contaminated and it hardens with time 5.1 Once a valve is removed from service, it
when it is static. Proper control of the should be cleaned immediately. The
drilling fluid will help reduce corrosion longer a valve sits with mud inside, the
and wear from contamination, but static harder the mud will become and it will
hardening is the real enemy. The ball is become more difficult to repair.
spherical and the cavity it fits into is
cylindrical so there is an annular space 5.2 Disassemble, per the previous section,
around the ball and seats where the clean every internal component, as well
mud will enter then sit and harden. A as the inside of the valve thoroughly,
more frequent maintenance schedule preferably with a high pressure and / or
will avoid failure. Frequent pressure temperature washer or using a mild
testing of the valve does not affect solvent with a stiff nylon brush, to
operation, even if it is tested from remove all contaminants. Use of highly
above. The internal components are abrasive pads or power tools is not
made from premium materials to recommended on sealing areas as
combat the effects of corrosion, these areas are critical surface finishes
designed to withstand working pressure, and dimensions.
processed to ensure extended life, and
tested at final acceptance.
22397 White Oak Drive • Conroe, Texas 77306-8859 • Tel: 281-399-8771 • Fax: 281-399-8773 • www.packardusa.com
4/5
 TWO PIECE KELLY VALVES
OPERATION AND MAINTENANCE PROCEDURE REV 2 –
01/2012

5.3 Once everything is cleaned, parts

should be inspected for damage or wear
in the seal areas. The seal areas are:
the OD of the ball, the areas of the
seats that touch the ball, the areas of
the seats near the rubber seals, and the NOTE: Failure to follow the above procedure explicitly
seat cavities in the valve body. Worn or may result in damage and subsequent premature
damaged parts and all rubber o-rings valve failure.
must be replaced. Prior to assembly,
new parts should be inspected and
coated with the proper greases.

5.4 Stem O-ring should be installed then

coated with Liquid-O-Ring PM600
Military Grease. After installing the ring
in its groove, a small blob of grease
should be put in one spot and pushed
around the ring and into the open space
in the o-ring groove
ISO9001:2008 # 0163 API # 7-1-0207
5.5 Seats and Sub O-rings should be
installed then coated with Liquid-O-Ring
600/1 Valve Life grease. After installing
the rings in their grooves, a small blob
of grease should be put in one spot and
pushed around the rings and into the
open spaces in the o-ring grooves
5.6 Liberally the spherical surface of the ball
with Liquid-O-Ring 600/1 Valve Life
grease.

5.7 After assembly, the valve should be

pressure tested at low pressure (1.7
MPa) and at working pressure per the
previous instructions. Hydrostatic shell
test need only be performed once on
each valve, by Packard, at Final
Acceptance Testing.

5.8 Once the valve passes hydrostatic test,

the end connections should be coated
with Liquid-O-Ring ZN-50 Tool Joint and
Drill Collar Compound, and thread
protectors should be installed
immediately.

5.9 The valve can then be placed back into

service or stored for later use.

5.10 If the valve is not put into service, store

the valve in a dry place standing on its
pin end or laying on its side.

5.11 In summation, control of the drilling

fluid, proper use, control of the
maintenance interval, and proper
maintenance routines will ensure long
service life.

22397 White Oak Drive • Conroe, Texas 77306-8859 • Tel: 281-399-8771 • Fax: 281-399-8773 • www.packardusa.com
5/5