High Frequency Inverter

Design Fundamentals

Chandrashekar DR
April 19, 2010
 Agenda
By the End of this session we will…

Understand different kinds of back up systems

Discuss building blocks of basic inverter

Discuss the evolution of the inverter topologies

Understand bi-directional inverter

List merits and de-merits of each type of inverter

Understand how high frequency inverter addresses the
short-falls of conventional inverter

Discuss design intricacies of high frequency inverter

Understand processor requirements of HF inverter

Magphy systems confidential April 19, 2010 2

 Basic building blocks of an inverter

Bypass path

Input AC-DC
DC-AC, Output
Bat
Inverter
Charging

Input voltage directly

switches the change
over relay

Magphy systems confidential April 19, 2010 3

 Inverter? UPS? confusion
Bypass path

Input AC-DC Outp

DC-AC,
Bat
Inverter ut
Charging
Change overtime
Inverter
>= 10 ms

Bypass path

Input AC-DC
Bat
DC-AC, Outp
ut Change overtime
UPS
Inverter
Charging

< 10 ms
Line interactive

Input AC-DC DC-AC, Output

Bat Charging Inverter

UPS Change over time

Online =0

Magphy systems confidential April 19, 2010 4

 Early inverters (Design-1)

Bypass path

Input

50Hz signal
generator

Xformer
Regulator

Amplifier
Rectifier
Xformer

Output

Input voltage directly

switches the change
over relay

Magphy systems confidential April 19, 2010 5

 Merits and de-merits of this
topology
• Very Simple design. Many earlier designs did not even
have a PCB!
• Uses 2 transformers; expensive and bulky
• Yet, only one transformer is in use at a time
• No intelligent element in the design, Most operations
happen by preset parameters
• Un-controlled charge and discharge cycles
• Not a closed loop system to ensure stable output
• Signal generator is usually a multi-vibrator and the output
is not a pure sine wave.
• Early designs used transistor banks which were prone to
failure

Magphy systems confidential April 19, 2010 6

 Bi-directional inverter topology (Design-2)

Regulator

Input
Rectifier

Transformer
Output

generator

Amplifier
Signal

Intelligence: uC/DSC

Magphy systems confidential April 19, 2010 7

 Changes from Design 1 to Design 2
• Addition of an intelligent element i.e., uC or DSC
• Pure sine wave generated by PWM technique
• One of the transformers eliminated
• Addition of DSC/uC enables a variety of new useful
functions
• Synchronous transition of load from Mains to Inverter
and vice-versa
• Closed loop control implemented through software
• Intelligent protection mechanisms implemented thro’
software

Magphy systems confidential April 19, 2010 8

 PWM Technique

Magphy systems confidential April 19, 2010 9

 Example implementation:
Bi-directional topology

• A very simple topology, almost

all the building blocks are bi-
directional
• Digital signal controller (not
shown in the picture) manages
the charging, discharging and
signal generation by
manipulating the gate drives of
the switching elements
• DSC Generates pure 50 Hz
sine wave using PWM technique
• Software can control output
voltage, wave shape, frequency
etc in real time.

Magphy systems confidential April 19, 2010 10

 Example implementation:
Bi-directional topology

• A very simple topology, almost

all the building blocks are bi-
directional
• Digital signal controller (not
shown in the picture) manages
the charging, discharging and
signal generation by
manipulating the gate drives of
the switching elements
• DSC Generates pure 50 Hz
sine wave using PWM technique
• Software can control output
voltage, wave shape, frequency
etc in real time.

Magphy systems confidential April 19, 2010 11

 Example implementation:
Bi-directional topology

• A very simple topology, almost

all the building blocks are bi-
directional
• Digital signal controller (not
shown in the picture) manages
the charging, discharging and
signal generation by
manipulating the gate drives of
the switching elements
• DSC Generates pure 50 Hz
sine wave using PWM technique
• Software can control output
voltage, wave shape, frequency
etc in real time.

Magphy systems confidential April 19, 2010 12

 What we need from a DSC to do all
these?
Function Number Application
PWM 4 4x Inverter PWM signals

ADC 7 1x Battery Voltage

2x Battery Current
1x Mains voltage
1x Output voltage
1x Temperature sensor
GPIO 8 Zero cross+, Zero cross –
Change over relay
Alarm, LED/LCD,
Front panel switch

External interrupts 1 Short circuit

Magphy systems confidential April 19, 2010 13

 Merits and challenges of bi-directional
topology
Merits:
• Cost reduction due to elimination of 1 transformer
• Addition of a Digital signal controller gives more flexibility and
control to designers
• Enables implementation of additional features and protection
mechanisms
Challenges
• Increased complexity
• Processor working in a noisy environment needs effective
noise isolation
• Transformer is used as a bidirectional device. Copper losses
during charging cycles are very high compared to earlier
design-1 topology

Magphy systems confidential April 19, 2010 14

 Need for improvements
Bi-directional Inverter design has
three drawbacks
1. Poor energy efficiency during
charging cycles due to higher iron
losses has to be overcome

2. Still heavy and bulky due to

transformer. Expensive to build and
expensive logistics. Need a lighter
solution

3. Noisy operation as the inverter

transformer operates at 50Hz
(audible frequency)
Magphy systems confidential April 19, 2010 15
 A new topology !!!
• How to address these needs?
• How to build a solution brick by brick?
• Should we stick to bi-directional
topology?
• Advent of High frequency inverter
• New challenges!!

Magphy systems confidential April 19, 2010 16

 Working on the improvements
Battery charger:
• Battery charger is essentially a regulated DC power supply
which can operate in constant current and constant voltage
modes as desired
• The voltage, the current, when to operate in which mode is
defined by the type of the battery and the battery voltage
• Regulator should be able to dynamically switch between the
modes
• Switch mode power supplies can fulfill these requirements,
and this also operates at high frequency (20KHz- 200KHz),
Hence no audible noise
• Health monitoring can help improve battery life and
performance. Help of a Digital signal controller comes in handy

Magphy systems confidential April 19, 2010 17

 Example Battery charging cycle

Lead-Acid battery

Magphy systems confidential April 19, 2010 18

 Typical switching power supply
controlled by Digital Signal Controller

• Pulse width is controlled by Digital signal controller so that the required voltage
and current are achieved as per the battery specifications
• Charging voltage and current are measured thro’ ADC inputs of the digital
signal controller. A closed loop control is implemented in software.

Magphy systems confidential April 19, 2010 19

 How to make 230V AC from 12/24V DC?
… well without the transformer being bulky and noisy

Generate
12/24AC 50Hz Amplify to Step up 12/24V
signal from required power to 230V
12/24V DC

Vs

Step up 12/24V Shape 50Hz

DC to √2*230V wave from
DC √2*230V DC

Magphy systems confidential April 19, 2010 20

 Step-up: Battery booster
• Generate PWM to drive the switching
Step up
12/24V DC elements (MOSFET)
to √2*230V • PWM block of DSCs are useful to
DC generate the PWMs
• Higher frequencies between 20KHz
to 200KHz can be used
• Step up with a high frequency
transformer
• Higher frequency transformers are
smaller and lighter compared to their
50Hz counterparts
• PCB mounted transformer can be
used
• Convert back to DC with simple
rectifiers
• Rectified output should be √2 * 230V
• Use ripple filters as needed
Gates are driven by digital signal processor
Magphy systems confidential April 19, 2010 21
 High Frequency transformer

Before After

Magphy systems confidential April 19, 2010 22

 High Frequency transformer
…What makes them slim?

Flux density, which is the key design factor of a transformer, is a function of

both cross sectional area of the core and frequency

Bmax = Vrms×108/4.44N×Ac×F for sine waves

Bmax = Vpk×108/4N×Ac×F for square waves
In this equations: V - voltage (volts), N - winding's turns, Ac - core's cross-sectional area (sq.cm),
F- frequency (hertz)

Desired flux density can be achieved by reducing the cross sectional area
of the core but increasing the frequency

+
For a given wattage, the ferrite core HF transformers operate with lower flux
densities than the Iron core transformers

Magphy systems confidential April 19, 2010 23

 50 Hz Sine wave shape using PWM
• Generate PWM to drive the switching
Shape 50Hz elements
wave from
• PWM block of DSCs are useful to
√2*230V DC
generate the PWMs
• Higher frequencies between 20KHz
to 200KHz can be used
• High voltage MOSFETs or IGBTs are
used for the switching bridge
• Frequency of operation and out put
power decide the choice of IGBT or
MOSFET
• Gate drive circuitry has to be
galvanic isolated from the digital plane
• A low pass filter at the output
produces continuous sine wave from
PWM signal

Magphy systems confidential April 19, 2010 24

 Complete discharge path

Magphy systems confidential April 19, 2010 25

 IGBT Vs MOSFET

MOSFET IGBT
Pcond = I2D(rms) * Rds(on)Hot * D Pcond = Vce(on) * Ic *D

Psw = Id * Vds * tSW * fSW Psw = Ets(Hot) * fSW

Negative thermal co-efficient Positive thermal co-efficient

fSW - switching frequency, Ets(Hot) - total switching losses (in data sheet)
tSW - total switching time (on + off, in data sheet)

Magphy systems confidential April 19, 2010 26

 IGBT/MOSFET Gate drive and
isolation

• PWM Switching elements are on the high voltage side of the transformer. It is
not safe for DSC or any other low voltage digital circuit to share anything with
this part of circuitry
• Individual ground references are required for each of the MOSFET/IGBT in the
bridge
• MOSFET/IGBT are voltage switched devices. They can be turned on easily by
applying the voltage to the gate. However, turning them off is tricky as they tend
to retain the voltage at gate due to gate junction capacitance. Special effort
should be made to turn them off.

Magphy systems confidential April 19, 2010 27

 Other necessary circuitry
 Battery Charge and discharge current sensing
• Implemented using a very low value resistor, an inverting amplifier and a non-
inverting amplifier and fed to the ADC inputs of the DSC
• Charge current readings are used to control the constant current and constant
voltage parameters of the charging circuitry

 Battery voltage sense

• Implemented using a potential divider to scale the voltage and fed to the ADC
input of the DSC
• Necessary for controlling the charge cycles and deep discharge protection

 Output voltage sense

• Implemented using a transformer and a full wave rectifier to scale down the
voltage
• Necessary for controlling battery booster PWMs and Inverter PWMs to ensure
stable output voltage

Magphy systems confidential April 19, 2010 28

 Other necessary circuitry … cntd
Mains voltage sense and Zero cross sense
• Mains sense implemented using a transformer and a full wave rectifier to scale
down the voltage
• Necessary for controlling change over relay in the event of mains failure
• Zero cross sensors are implemented using voltage comparators in conjunction
with mains transformer
• These signals help the DSC to know whether the main is in positive or negative
cycles. This is essential for synchronous transfer of load from mains to inverter
and vice versa

 DC-DC converters/LDOs
• 5V DC and 3.3V DC needed for the operation of Op-Amps and the DSC are
derived from battery voltage using either LDOs or DC-DC converters

 Temperature sensor
• Implemented using a thermister, and connected to DSC, Used to protect
MOSFETs/ IGBTs from over-heating

Magphy systems confidential April 19, 2010 29

 Other necessary circuitry … cntd
 Change over relay
• Instrumental in transition of the load between the mains supply and the inverter
output

 Isolated DC sources
•3 isolated DC sources with independent ground references are required to power
each of the 4 MOSFET/IGBT gate drivers. Both the low-side IGBT gate drivers
may share the same supply as they share the same net for the source pins.
• can be implemented by adding 3 additional 15 V secondary windings in the main
transformer.

Magphy systems confidential April 19, 2010 30

 Bells and whistles…
LED / LCD display
• Useful as user interface to convey the status of the system visually

 Audio alarm
• Useful as user interface to convey the status of the system visually

 Front panel switch

• To switch the system between various modes

 USB/Serial interface
• Provide computer connectivity; can be used for remote management, data
logging, etc…

Magphy systems confidential April 19, 2010 31

 Architecture
Block diagram

Magphy systems confidential April 19, 2010 32

 What we need from a DSC to do all
these?
Function Number Application
PWM 9 4x Inverter PWM signals
4x Battery booster PWM signals (2 if a centre
tap transformer used)
1x Battery charger PWM signal
ADC 8 1x Battery Voltage
2x Battery Current
1x Mains voltage
1x Output voltage
1x Temperature sensor
1x HVDC sense
GPIO 8 Zero cross+, Zero cross –
Change over relay
Alarm, LED/LCD,
Front panel switch

External interrupts 2 MOSFET/IGBT fail

Short circuit

Magphy systems confidential April 19, 2010 33

 Recommended devices from
Freescale

http://www.freescale.com/webapp/sps/site/homepage.jsp?code=DSC_HOME

Magphy systems confidential April 19, 2010 34

 About Magphy… www.magphy.com
 Magphy Expertise
The Magphy team has a strong background of designing complex embedded systems from
past experience. We have contributed in designing many SBCs, telecom blades, media players
and other embedded systems that are in service today, both in terms of hardware design and
software development. Innovation and quality have been our forte as we have built our careers.

 Magphy Experience
The Magphy team comes with a very rich experience in Embedded systems design. All in all,
the current team has more than 50 man years of experience in this domain. We have a vast
experience in providing industry standard solutions as well as custom specific solutions that are
modular, scalable and efficient.

 Magphy Focus
Magphy systems focus on the emerging Energy and automotive sectors. We believe that the
emphasis, growth and growing technology content in these sectors promise growth of Magphy.

 Magphy Founders
Magphy is floated by some of the very experienced Managers and senior engineers of the
Embedded computing industry. We also share the common vision of providing high quality and
cost effective solutions to the industry

Magphy systems confidential April 19, 2010 35

 Thank you

Magphy systems confidential April 19, 2010 36