DESIGN CALCULATION REPORT Page 1222 of 7938

Job No. FM5-1471 Building No. 01 Rev. No. R0

Customer PepsiCo India Holdings Pvt. Ltd. Date 28-Oct-13
Description Packing Area,Filling Area,Syrup Area,RM Designed By SSD/SSS
Warehouse,Dock,Chemical store (FL- 13 to 30)
Checked By SPR
16 Segment 20, Section 127, Load 2 1.5Dead+1.5Collateral+1.05Live
17 Segment 21, Section 136, Load 2 1.5Dead+1.5Collateral+1.05Live
18 Segment 22, Section 139, Load 2 1.5Dead+1.5Collateral+1.05Live
19 Segment 23, Section 141, Load 2 1.5Dead+1.5Collateral+1.05Live
20 Segment 24, Section 150, Load 2 1.5Dead+1.5Collateral+1.05Live
21 Segment 25, Section 156, Load 50 1.2Dead+1.2Collateral+0.53Live-1.2Seismic
22 Segment 26, Section 161, Load 50 1.2Dead+1.2Collateral+0.53Live-1.2Seismic
23 Segment 27, Section 164, Load 50 1.2Dead+1.2Collateral+0.53Live-1.2Seismic

DESIGN RESULTS:
W_Check RfDes-1
---Calculated_UC--- -----Output_UC-----
Report Axial+Moment Axial+Moment
Id Shear Top Bottom Shear Top Bottom
------ ----- ----- ------ ----- ----- ------
1 0.24 0.07 0.44 0.24 0.07 0.44
2 0.16 0.31 0.52 0.16 0.31 0.52
3 0.50 0.37 0.79 0.50 0.37 0.79
4 0.13 0.50 0.10 0.13 0.50 0.10
5 0.26 0.29 0.39 0.26 0.29 0.39
6 0.88 0.53 1.00 0.88 0.53 1.00
7 0.42 0.18 0.75 0.42 0.18 0.75
8 0.01 0.76 0.33 0.01 0.76 0.33
9 0.00 0.76 0.33 0.00 0.76 0.33
10 0.42 0.17 0.74 0.42 0.17 0.74
11 0.87 0.52 0.99 0.87 0.52 0.99
12 0.55 0.51 0.93 0.55 0.51 0.93
13 0.59 0.43 0.85 0.59 0.43 0.85
14 0.01 0.86 0.37 0.01 0.86 0.37
15 0.01 0.90 0.37 0.01 0.90 0.37
16 0.52 0.29 0.91 0.52 0.29 0.91
17 0.54 0.51 0.85 0.54 0.51 0.85
18 0.65 0.38 0.84 0.65 0.38 0.84
19 0.60 0.30 0.72 0.59 0.30 0.72
20 0.71 0.23 0.80 0.71 0.23 0.80
21 0.42 0.41 0.89 0.42 0.41 0.89
22 0.37 0.08 0.53 0.37 0.08 0.53
23 0.21 0.11 0.49 0.21 0.11 0.49
/*

================================================================================
FUT-2-Low-bay-Pepsi Strength Check 10/31/13 10:07am
================================================================================

DESCRIPTION: Segment 1, Section 5, Load 50 1.2Dead+1.2Collateral+0.53Live-1.2Seismic

MEMBER
Member Part - --------
Web Depth (mm) - 1750.0 UNITS(kN,kN-m)
Web Thick (mm) - 10.0 ACTION CALC LIMIT RATIO EQUATION
Flange Width (mm) - 400.0 --------- ------ ------ ----- --------
Top Flange Thick(mm)- 20.0 Axial 603.82 3268.44 0.18 7.1.2
Bot Flange Thick(mm)- 20.0
Yield Flange(MN/m2) - 345 Shear -122.88 502.33 0.24 8.4.2
Yield Web (MN/m2) - 345
 DESIGN CALCULATION REPORT Page 1223 of 7938
Job No. FM5-1471 Building No. 01 Rev. No. R0
Customer PepsiCo India Holdings Pvt. Ltd. Date 28-Oct-13
Description Packing Area,Filling Area,Syrup Area,RM Designed By SSD/SSS
Warehouse,Dock,Chemical store (FL- 13 to 30)
Checked By SPR
Stiffener Space(mm) - 0.0 Bending_Top 782.95 6117.39 0.13
UNBRACED LENGTH (Tension)
Major Axis (mm) - 12745.4
Minor Axis Axial(mm)- 8000.0 Bending_Bot 782.95 2878.04 0.27
Minor Axis Top (mm) - 8000.0 (Compression)
Minor Axis Bot (mm) - 8000.0
CONSTANTS Axial+Bending_Top 0.07
mo - 1.100
m1 - 1.250 Axial+Bending_Bot 0.44
m2 - 1.000
C1 - 2.230 MEMBER CLASSIFICATION
C3 - 2.110 Axial : Web = Slender , Flange = Semi-Compact
 - 0.000 Bending: Web = Slender , Flange = Semi-Compact
Tension Coefficient - 1.000
Ultimate/Yield - 1.300 SLENDERNESS
ACTION Major Axis 17.89
Axial (kN) - 603.816 Minor Axis 100.21
Shear (kN) - -122.882
Moment (kN-m) - 782.948

/*

CALCULATION SHEET

DESIGN BASIS = LIMIT STATES (LS)

SECTION SIZE
Member Part = --------
d, Total Depth = 1790.0 mm
hw, Web Depth = 1750.0 mm
tw, Web Thickness = 10.0 mm
bf, Flange Width = 400.0 mm
tft, Top Flange Thickness = 20.0 mm
tfc, Bottom Flange Thickness = 20.0 mm

MATERIAL
2
Fyf, Flange Yield Stress = 345 MN/m
2
Fuf, Flange Ultimate Stress = 449 MN/m
2
Fyw, Web Yield Stress = 345 MN/m
2
Fuw, Web Ultimate Stress = 449 MN/m
2
E, Modulus of Elasticity = 200000 MN/m
2
G, Shear Modulus = 76900 MN/m

UNBRACED LENGTHS
Major Axis = 12745.4 mm
Minor Axis (Axial) = 8000.0 mm
Minor Axis, top flange = 8000.0 mm
Minor Axis, bottom flange, Lb = 8000.0 mm
C1, moment diagram coefficient = 2.23
C3, moment diagram and member cross section = 2.11
, shape of moment diagram = 0.00

CONSTANTS
 DESIGN CALCULATION REPORT Page 1224 of 7938
Job No. FM5-1471 Building No. 01 Rev. No. R0
Customer PepsiCo India Holdings Pvt. Ltd. Date 28-Oct-13
Description Packing Area,Filling Area,Syrup Area,RM Designed By SSD/SSS
Warehouse,Dock,Chemical store (FL- 13 to 30)
Checked By SPR
mo, partial safety factor for yielding and buckling = 1.10
m1, partial safety factor for ultimate strength = 1.25
Cn, tension area coefficient = 1.00
Ultimate strength / yield strength = 1.30

LOADING - FACTORED LOADS

P, Axial (Compression) = 603.82 kN
V, Shear (major axis) = -122.88 kN
M, Moment (major axis, bottom flange in compression) = 782.95 kN-m

MEMBER CLASSIFICATION (Section 3.7.2)

e =√(250/Fyf) = 0.851
FLANGE CLASSIFICATION (AXIAL AND BENDING)
bf/(2*tfo) = 9.75
bf/(2*tfi) = 9.75
Plastic limit = 8.4*e = 7.15
Compact limit = 9.4*e = 8.00
Semi-Compact limit = 13.6*e = 11.58
Top Flange Class = Semi-Compact
Bot Flange Class = Semi-Compact
WEB CLASSIFICATION (AXIAL)
d/tw = 175.00
Semi-Compact limit = 42*e = 35.75
Web Class = Slender
EFFECTIVE WEB DEPTH
deff = d*[(d/twlimit)/(d/tw)] = 357.5 mm
Web depth removed = d-deff = 1392.5 mm
WEB CLASSIFICATION (BENDING)
Plastic limit = 84*e = 71.51
Compact limit = 105*e = 89.38
Semi-Compact limit = 126*e = 107.26
Web Class = Slender
EFFECTIVE WEB DEPTH
deff = d*[(d/twlimit)/(d/tw)] = 1072.6 mm
Web depth removed = d-deff = 677.4 mm

SECTION PROPERTIES
d, overall member depth = 1790.0 mm
ho, distance between flange centroids = 1770.0 mm
2
Ag, gross area = 335.00 cm
Ybar, centroid, from bottom = 895.0 mm
4
Ix, major axis moment of inertia = 1699827.6 cm
3
Sxt, elastic section modulus, tension flange = 18992.5 cm
3
Sxc, elastic section modulus, compression flange = 18992.5 cm
rx, major axis radius of gyration = 712.3 mm
4
Iy, minor axis moment of inertia = 21347.9 cm
3
Sy, elastic section modulus for y-axis = 1067.4 cm
ry, minor axis radius of gyration = 79.8 mm
3
Zx, plastic section modulus = 21816.3 cm
4
J, Torsional Constant = 271.667 cm
rt, torsion radius of gyration = 98.9 mm
3
Iyc, minor axis moment of inertia in compression = 4199.5 cm
 DESIGN CALCULATION REPORT Page 1225 of 7938
Job No. FM5-1471 Building No. 01 Rev. No. R0
Customer PepsiCo India Holdings Pvt. Ltd. Date 28-Oct-13
Description Packing Area,Filling Area,Syrup Area,RM Designed By SSD/SSS
Warehouse,Dock,Chemical store (FL- 13 to 30)
Checked By SPR
3
Iyt, minor axis moment of inertia in tension = 4199.5 cm
6
Cw, warping constant = 167202208 cm
xo, shear center with respect to centroid of section = 0.0 mm
yo, shear center with respect to centroid of section = 0.0 mm
ro, polar radius of gyration about shear center = 716.8 mm
 x, asymmetry parameter = 0.0 mm

EFFECTIVE (COMPRESSION)
Flange: Top = 20x400.0, Bottom = 20x400.0
Web: 10x1750.0 with 1392.5 removed at mid depth
2
Ae, Effective Area = 195.75 cm
yg, inside to C.G. = 895.0 mm
4
Ixe, major axis = 1474829.6 cm
3
Sexo, top flange = 16478.6 cm
3
Sexi, bottom flange = 16478.6 cm
rx, major axis = 868.0 mm
4
Iye, minor axis = 21336.3 cm
ry, minor axis = 104.4 mm
EFFECTIVE (FLEXURE)
Flange: Top = 20x400.0, Bottom = 20x400.0
Web: 10x1750.0 with 677.4 removed at inside edge of compressive stress
2
Ae, Effective Area = 267.26 cm
yg, inside to C.G. = 963.5 mm
4
Ixe, major axis = 1611922.3 cm
3
Sexo, top flange = 19502.8 cm
3
Sexi, bottom flange = 16730.0 cm
rx, major axis = 776.6 mm
4
Iye, minor axis = 21347.9 cm
ry, minor axis = 89.4 mm

SHEAR STRENGTH, (8.4.2.2.a)

d/tw for web = 175.00
d/tw limit = 67*e = 57.03
d/tw is > 67*e, so web buckling is used.
2 2
Elastic critical shear stress, cr.e=180762*Kv/(d/tw) = 31.6 MN/m
0.5
Web slenderness, w = [Fyw/(1.732*cr.e)] = 2.512
Since w >= 1.2, Web buckling shear stress
2 2
b = Fyw/(1.732*w ) = 31.6 MN/m
2
Shear area, Av; W member, d*tw = 175.00 cm
Shear force for web buckling, Vd = Av*b/mo = 502.33 kN
Ratio = V/Vd = 0.2446

AXIAL STRENGTH
COMPRESSION OF SLENDER SECTIONS, (Section 7)
MAJOR AXIS
Lx, major axis length = 12745.4 mm
K*Lx/rx major = 14.68
2 2 2
Fcc =  *E/(K*Lx/rx) = 9154.91 MN/m
x =√(Fyf/Fcc) = 0.1941
 for a W section = 0.34
2
 = 0.5*[1+(x-0.2)+x ] = 0.5178
 DESIGN CALCULATION REPORT Page 1226 of 7938
Job No. FM5-1471 Building No. 01 Rev. No. R0
Customer PepsiCo India Holdings Pvt. Ltd. Date 28-Oct-13
Description Packing Area,Filling Area,Syrup Area,RM Designed By SSD/SSS
Warehouse,Dock,Chemical store (FL- 13 to 30)
Checked By SPR
2 2 0.5 2
Fcd = (Fyf/mo)/(+[ -x ] ) <= Fyf/mo = 313.64 MN/m
Pdx = Ae*Fcd = 6139.00 kN
MINOR AXIS
Ly, minor axis length = 8000.0 mm
K*Ly/ry minor = 76.63
2 2 2
Fcc =  *E/(K*Ly/ry) = 336.17 MN/m
y =√(Fyf/Fcc) = 1.0130
 for minor axis = 0.49
2
 = 0.5*[1+(y-0.2)+y ] = 1.2123
2 2 0.5 2
Fcd = (Fyf/mo)/(+[ -y ] ) <= Fyf/mo = 166.98 MN/m
Pdy = Ae*Fcd = 3268.44 kN
Pd = Minimum of Pdx and Pdy = 3268.44 kN
Ratio = P/Pd = 0.1847

BENDING STRENGTH
TENSION FLANGE
Flange in tension = Top
b = Sexo/Zx = 0.8940
Mdt = b*Zx*Fyf/mo = 6117.39 kN-m
Ratio = M/Mdt = 0.1280

COMPRESSION FLANGE
Flange in compression = Bottom
LLT, effective length for lateral torsional buckling = 8000.0 mm
4
It = J, torsional constant = 271.667 cm
3
Iw = Cw, warping constant = 167202208 cm
2 2 2 2 0.5
Mcr=([ *E*Iy/(LLT) ]*[G*It+ *E*Iw/(LLT) ]) = 5944.48 kN-m
3
Sexi = 16730.0 cm
b = Sexi/Zx = 0.7669
Slenderness ratio, LT
0.5
LT = [b*Zx*Fyf/Mcr] = 0.9854
0.5
<= (1.2*Sexi*Fyf/Mcr) = 1.0795
Since LT > 0.4, member is laterally unsupported.
LT, W sections = 0.49
2
LT = 0.5*[1+LT*(LT-0.2)+LT ] = 1.1780
2 2 0.5
XLT = 1/(LT+[LT -LT ] ) <= 1.0 = 0.5484
Design bending compressive stress, fbd
2
fbd = XLT*Fyf/mo = 172.0 MN/m
Md = b*Zx*fbd = 2878.04 kN-m
Mdc = Md = 2878.04 kN-m
Ratio = M/Mdc = 0.2720

AXIAL + BENDING
P, required axial strength = 603.82 kN
Pdy = compressive strength (out of plane, minor axis) = 3268.44 kN
Pdx = compressive strength (in plane, major axis) = 6139.00 kN
M, required bending strength = 782.95 kN-m
Mdc = bending strength, compression flange = 2878.04 kN-m
Mdt = bending strength, tension flange = 6117.39 kN-m
x, from axial strength calculations = 0.194
LT, from axial strength calculations = 0.985
 DESIGN CALCULATION REPORT Page 1227 of 7938
Job No. FM5-1471 Building No. 01 Rev. No. R0
Customer PepsiCo India Holdings Pvt. Ltd. Date 28-Oct-13
Description Packing Area,Filling Area,Syrup Area,RM Designed By SSD/SSS
Warehouse,Dock,Chemical store (FL- 13 to 30)
Checked By SPR
Pd = Ag*Fy/mo = 10505.93 kN

TENSION FLANGE
MEMBER
-(P/Pdy)+KLT*M/Mdt <= 1.0 = -0.0634
-(P/Pdx)+Kx*Cmz*M/Mdt <= 1.0 = 0.0168
SECTION
-P/Pdt+M/Mdt <= 1.0 = 0.0705
Ratio, maximum of Member and Section = 0.0705

COMPRESSION FLANGE
 = 0.0000
CmLT = 0.6+0.4* >= 0.4 = 0.6000
Kx = 1+(x-0.2)*P/Pdx <= 1+0.8*P/Pdx = 0.9994
KLT = 1-0.1*LT*P/(Pdy*(CmLT-0.25))
KLT >= 1.0-0.1*P/(Pdy*(CmLT-0.25))
KLT = 0.9480
Cmx = 0.9000
MEMBER
P/Pdy+KLT*M/Mdc <= 1.0 = 0.4426
P/Pdx+Kx*Cmz*M/Mdc <= 1.0 = 0.3431
SECTION
P/Pdt+M/Mdc <= 1.0 = 0.3295
Ratio, maximum of Member and Section = 0.4426

/*
================================================================================
FUT-2-Low-bay-Pepsi Strength Check 10/31/13 10:07am
================================================================================

DESCRIPTION: Segment 2, Section 11, Load 50 1.2Dead+1.2Collateral+0.53Live-1.2Seismic

MEMBER
Member Part - --------
Web Depth (mm) - 1750.0 UNITS(kN,kN-m)
Web Thick (mm) - 12.0 ACTION CALC LIMIT RATIO EQUATION
Flange Width (mm) - 400.0 --------- ------ ------ ----- --------
Top Flange Thick(mm)- 20.0 Axial 276.12 5111.81 0.05 7.1.2
Bot Flange Thick(mm)- 20.0
Yield Flange(MN/m2) - 345 Shear -136.68 868.03 0.16 8.4.2
Yield Web (MN/m2) - 345
Stiffener Space(mm) - 0.0 Bending_Top2136.51 6395.27 0.33
UNBRACED LENGTH (Tension)
Major Axis (mm) - 12745.4
Minor Axis Axial(mm)- 4745.4 Bending_Bot2136.51 4561.95 0.47
Minor Axis Top (mm) - 4745.4 (Compression)
Minor Axis Bot (mm) - 4745.4
CONSTANTS Axial+Bending_Top 0.31
mo - 1.100
m1 - 1.250 Axial+Bending_Bot 0.52
m2 - 1.000
C1 - 1.000 MEMBER CLASSIFICATION
C3 - 1.000 Axial : Web = Slender , Flange = Semi-Compact
 DESIGN CALCULATION REPORT Page 1228 of 7938
Job No. FM5-1471 Building No. 01 Rev. No. R0
Customer PepsiCo India Holdings Pvt. Ltd. Date 28-Oct-13
Description Packing Area,Filling Area,Syrup Area,RM Designed By SSD/SSS
Warehouse,Dock,Chemical store (FL- 13 to 30)
Checked By SPR
 - 0.620 Bending: Web = Slender , Flange = Semi-Compact
Tension Coefficient - 1.000
Ultimate/Yield - 1.300 SLENDERNESS
ACTION Major Axis 18.33
Axial (kN) - 276.116 Minor Axis 62.46
Shear (kN) - -136.682
Moment (kN-m) - 2136.513

/*

CALCULATION SHEET

DESIGN BASIS = LIMIT STATES (LS)

SECTION SIZE
Member Part = --------
d, Total Depth = 1790.0 mm
hw, Web Depth = 1750.0 mm
tw, Web Thickness = 12.0 mm
bf, Flange Width = 400.0 mm
tft, Top Flange Thickness = 20.0 mm
tfc, Bottom Flange Thickness = 20.0 mm

MATERIAL
2
Fyf, Flange Yield Stress = 345 MN/m
2
Fuf, Flange Ultimate Stress = 449 MN/m
2
Fyw, Web Yield Stress = 345 MN/m
2
Fuw, Web Ultimate Stress = 449 MN/m
2
E, Modulus of Elasticity = 200000 MN/m
2
G, Shear Modulus = 76900 MN/m

UNBRACED LENGTHS
Major Axis = 12745.4 mm
Minor Axis (Axial) = 4745.4 mm
Minor Axis, top flange = 4745.4 mm
Minor Axis, bottom flange, Lb = 4745.4 mm
C1, moment diagram coefficient = 1.00
C3, moment diagram and member cross section = 1.00
, shape of moment diagram = 0.62

CONSTANTS
mo, partial safety factor for yielding and buckling = 1.10
m1, partial safety factor for ultimate strength = 1.25
Cn, tension area coefficient = 1.00
Ultimate strength / yield strength = 1.30

LOADING - FACTORED LOADS

P, Axial (Compression) = 276.12 kN
V, Shear (major axis) = -136.68 kN
M, Moment (major axis, bottom flange in compression) = 2136.51 kN-m

MEMBER CLASSIFICATION (Section 3.7.2)

e =√(250/Fyf) = 0.851