Ex Pan Proof 600

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

CONSTRUCTION CHEMISTRY

Expanproof* 600
Liquid applied single component elastomeric
waterproofing membrane

Uses Properties

The high elasticity, excellent bond and low water Tack free time @ 25°C : 15 hours
permeability of Expanproof* 600 make it ideal for a wide
Time to full cure @ 25°C : 48 hours @ 1.3mm
range of water/vapour proofing applications such as
thickness
foundations, basements, tunnels, ground floors,
suspended floors, car decks, roof terraces, balconies, Typical cured membrane properties (at 28 days)
patios, bridges, precincts, inspection pits, water retaining
Elongation
structures (not potable water), sewage works,
(ASTM D412) : 620 %
and inverted roofs. The excellent chemical resistance of
Expanproof* 600 makes it particularly suitable for tanking Tensile strength
applications in areas where aggressive ground water (ASTM D412) : 1.5 N/mm2
conditions prevail.
Modulus @ 100%
elongation
Advantages
(ASTM D412) : 0.62 N/mm2
• One component; ready to apply direct from the can Recovery from 200%
• Liquid application means details are simplified and elongation
there are no joints in the membrane (ASTM D412) : 95 %
• Highly elastic, cures to give a permanently flexible
Tear resistance
resilient barrier over a wide range of temperatures
(ASTM D624) : 15 N
• Rapid installation; significantly reduces time spent on
preparatory works and detailing Water vapour transmission
• Excellent adhesion, can be applied to a wide range for 1.3mm film
of substrates. Continuous adhesion prevents lateral (ASTM E96) : 9.7 g/m2/24 hrs.
migration of water
Permeability
• Impervious - outstanding barrier properties ensure
(ASTM E96) : 0.063 ng/m/sec/Pa*
protection against corrosive soil conditions
• Thermally stable - irreversible chemical cure eliminates Shore A hardness
melting and flow at high temperature (ASTM D2240) : 50
• Excellent resistance to oxidation and embrittlement
Artificial weathering : No loss of flexibility after
• Mechanical damage to the membrane can be easily
4000 hours exposure
repaired by spot application
Extensibility after heat
Standard compliance aging (min. requirement -
extended to 6.4mm
Expanproof* 600 meets the requirements of without cracking) : No cracking or tearing
ASTM C836- 84.
Service temperature
(continuous ambient) : -40°C to 70°C
Description
* 1ng = 10-12kg
Expanproof* 600 single component pitch modified
polyurethane cures by reaction with atmospheric moisture
Chemical properties
to give a tough elastomeric waterproof membrane. It is
supplied in a single grade to meet all site application
Expanproof* 600 is unaffected by a range of mild acids,
methods and requirements.
alkalis and water borne salts and is resistant to bio-
deterioration.
Expanproof* 600 is a medium viscosity grade
(approximately 600 poise) for roller, squeegee or spray
application to horizontal and vertical surfaces.
CONSTRUCTION CHEMISTRY

Instructions for use Right angle bends

Preparation All right angle bends must have a cant strip or coving
detail installed. This may be formed in either sand &
All surfaces to be waterproofed should be sound, clean cement or Expanseal* Putty* and it must be bedded into
and dry. a layer of Expanproof* 600, then given a reinforcing
pretreatment by application of a 1.3mm thick coat
Concrete surfaces should have a light steel-trowel extending 150mm either side of the coving. Whilst still
followed by a fine hair-broom or equivalent finish which wet, a 150mm wide strip of Expanproof* Scrim is
is dry and free of dust, oil and other contaminants. All embedded into the Expanproof* 600 as reinforcement
high spots should be removed. (ensure thorough wetting).

Moss and lichen must be removed physically followed All other angles, joints, protrusions and stress points
by treatment with fungicidal wash to kill any spores and should be pretreated with a heavy application of
inhibit further growth. After treatment wash down Expanproof* 600 extending 50-100mm either side of the
thoroughly with clean water and allow to dry. detail. Reinforcement with Expanproof* Scrim is
recommended where movement is possible.
All metal surfaces should be made clean of paint, oils,
rust and other contaminants. Abrade to expose bright Allow pretreatments to cure overnight before general
metal then wipe clean with Expanchem Solvent* 102 prior application.
to priming.
Application
Priming
Expanproof* 600 should be applied by brush, trowel,
Priming is not normally required on good quality concrete squeegee or airless spray (two coat application for
substrates. However, absorbent surfaces such as porous standard grade on vertical surfaces) at a minimum wet
concrete, sand/cement and cement boards will require film thickness of 1.3mm (1.3 liter/m²). This is in addition to
sealing to prevent absorption of Expanproof* 600. This the preparatory work.
should be done using a 1:1 mixture of Expanproof* 600
and Expanchem Solvent* 102. Use Expanprime* 32 as The minimum application life (after opening the pack) is
a primer for bituminous surfaces. All metal and PVC up to 48 hours if stored in closed containers.
surfaces should be cleaned and abraded before priming.
On a vertical surface a film build of 1.3mm is achievable
Movement joints in two coats. In critical applications where surety of film
thickness is paramount, two coats should be applied at
All expansion and movement joints should be sealed right angles to one another. Quantities per coat should
with Expanseal* 220. When cured, Expanseal* be gauged to give the specified final film thickness.
Debonding Tape should be applied to the top surface of
the sealant and the joint then over coated with a A short haired synthetic pile roller should be used if
1.3mm thick application of Expanproof* 600 extending applying by roller. For spray application, use a Graco
150mm each side of the tape. Embed a 100mm or King type pump with 60:1 ratio at pressure 5.5 bar (80
150mm wide strip of Expanproof* Scrim*, then allow to psi), hose diameter 13mm with a 10mm wip end. Tip
cure before general application. size: 0.58mm - 0.84 (23-33 thou).

Cracks If a water test is to be run, the membrane should be fully


cured.
All shrinkage and non-moving structural cracks should
be pretreated with not less than a 1.3mm coating of Flood test
Expanproof* 600 extending 75mm either side of the
crack. Allow to cure overnight before general application. Prior to placement of protection, flood to a minimum
depth of 50mm of water for 24 hours. Drains shall be
plugged and barriers placed to contain the water.
CONSTRUCTION CHEMISTRY

Storage

Curing and protection Shelf life

Expanproof* 600 membrane must be cured for a minimum Expanproof* 600 has a shelf life of 12 months if kept
of 24 hours @ 25°C before placing protection. Where below 25°C in the original, unopened packs.
damage to the membrane is possible (by traffic, backfilling,
etc) it should be protected by a cementitious screed or Expanprime* 32 has a shelf life of 12 months if kept in
protection boards. A dust coat of cement should be used a dry store in the original, unopened packs.
to prevent adhesion of the membrane to the boards.
Where a bond with the topping is not required, a separator Precautions
sheet should be used.
Health and safety
To prevent damage to the membrane it is recommended
that Expanproof* 600 is laid in strips of 1 metre width to Some people are sensitive to resin systems. Gloves and
permit the application of a screed or Protection Board a barrier cream such as Kerodex Antisolvent, Rozalex
from the uncoated area. Antipaint or Debba-Wet-Work should be used when
handling these products. If contact with the resin occurs
All exposed areas of Expanproof* 600 should be coated it must be removed before it hardens with a resin removing
with Expanproof* Reflectacoat* to ensure maximum cream such as kerocleanse Standard grade Skin cleanser
resistance to ultraviolet radiation. or Rozaklens Industrial Skin cleanser. Follow by washing
with soap and water. Do not use solvent. The use of
Cleaning goggles is recommended but should accidental eye
contamination occur, wash thoroughly with plenty of water
Tools and equipment should be cleaned with Expanchem and seek medical advice. Ensure adequate ventilation
Solvent* 102 immediately after use. Do not use the solvent when using resin and solvent containing materials.
for thinning except where a sealing coat is required.
Fire
Limitations
Expanproof* 600, Expanproof* Reflectacoat
a n d Expanchem Solvent* 102 contain flammable
- Application should not commence if the temperature
solvents. Do not use near an open flame or smoke
of the substrate is below 5°C.
during use.
Technical support Flash points

Expanchem Fospak offers a comprehensive range of Expanproof* 600 : 45°C


high performance, high quality repair, maintenance and
Expanproof* Reflectacoat : 23°C
construction products. In addition, Expanchem Fospak
offers a technical support package to specifiers, end- Expanchem Solvent* 102 : 33°C
users and contractors, as well as on-site technical
assistance in locations all over the world. For further information, refer to the Product Material
Safety Data Sheet.
Estimating

Supply
Expanproof* 600 : 20 liter drums
Expanprime* 32 : 1 liter packs
Expanproof* Reflectacoat : 20 liter can
Expanproof* Scrim : 1000 mm wide x 50 m
long
Expanchem Solvent* 102 : 5 liters can
Coverage
Expanproof* 600 : 0.76 m²/liter @ 1.3 mm
Expanprime* 32 : 5.0 m²/liter
CONSTRUCTION CHEMISTRY

Additional Information

Expanchem Fospak manufactures a wide range of


complementary products which include :

• waterproofing membranes & waterstops


• joint sealants & filler boards
• cementitious & epoxy grouts
• specialized flooring materials

Expanchem Fospak additionally offers a comprehensive


package of products specifically designed for the repair
and refurbishment of damaged concrete. Expanchem
Fospak’s ‘Systematic Approach’ to concrete repair
features the following :

• hand-placed repair mortars


• spray grade repair mortars
• fluid micro-concretes
• chemically resistant epoxy mortars
• anti-carbonation/anti-chloride protective coatings
• chemical and abrasion resistant coatings

For further information on any of the above, please


consult your local Expanchem Fospak office. * Denotes the trademark registered.

REGIONAL SALES OFFICES IN PAKISTAN:


Fospak (Pvt) Ltd. Lahore Sales Office Rawalpindi Sales Office
Head Office 2nd Floor Sarwar Shaheed Plaza, 1st Floor,
702, Business Avenue, Cavalry Ground, Al-Harmain Plaza,
Block-6, PECHS., Shahra-e-Faisal, Main Boulevard, Lahore Cantt, Main Murree Road,
Karachi, Pakistan. Lahore, Pakistan. Rawalpindi, Pakistan.
Tel # +92-21-34528477, 34529859 Tel # +92-42-36675773 Tel # +92-51-9290592
Fax # +92-21-34522436 Fax # +92-42-36675838 Fax # +92-51-9290590
Email : info.khi@fospak.com.pk Email : info.lhr@fospak.com.pk Email : info.isb@fospak.com.pk

Important note
Expanchem Fospak products are guaranteed against defective materials and manufacture and are sold subject
to its standard terms and conditions of sale, copies of which may be obtained on request. Whilst Epanchem Fospak
endeavours to ensure that the technical information on this data sheet is correct at the time of printing, it is the
customer’s responsibility to satisfy himself, by checking with the company that this information is still current at
the time of use, that the product is suitable for the intended application, and that the actual conditions of use are
in accordance with those recommended. Because Expanchem Fospak has no control over the conditions of use
of its products, all recommendations or suggestions regarding the use of these products are made without guarantee.

www.fospak.com

You might also like