BS5422 Insulation

BS 5422:2009
Incorporating Corrigendum No. 1
BSI British Standards
Method for specifying thermal

insulating materials for pipes,
Licensed copy:Royal Haskoning, 19/01/2015, Uncontrolled Copy, © BSI
tanks, vessels, ductwork and

equipment operating within
the temperature range –40 °C
to +700 °C
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
raising standards worldwide™

BS 5422:2009 BRITISH STANDARD
Publishing and copyright information

The BSI copyright notice displayed in this document indicates when the
document was last issued.
© BSI 2009
ISBN 978 0 580 69184 3
ICS 23.020.01, 27.220, 91.100.60
The following BSI references relate to the work on this standard:

Committee reference B/540/7
Draft for comment 08/30147222 DC
Publication history
First published July 1977
Second edition, July 1990
Third edition, December 2001
Fourth (present) edition, December 2008
Amendments issued since publication
Amd. No. Date Text affected

C1 November 2009 Tables 4, 5, 7, 9, 14, 15, 16, 20,

21, 27, 30, 31, A.1, C.1, D.1
8.3.3, 10.3.1
F.3 Note 4
See foreword
BRITISH STANDARD BS 5422:2009
Contents
Foreword iv
Introduction 1
1 Scope 2
2 Normative references 2
3 Terms and definitions 2
4 Application of this standard 4
5 General requirements 4
6 Refrigeration applications 8
7 Chilled and cold water applications 15
8 Central heating, air conditioning and direct hot water supply
installations in non-domestic applications 24
9 Central heating and hot water services for domestic
applications 32
10 Process pipework and equipment applications 36
11 Protection against freezing 50
Annexes
Annex A (informative) Underlying methodology 56
Annex B (informative) Default values for use in BS EN ISO 12241:1998
heat transfer calculations 58
Annex C (informative) Summary of criteria used to establish

the tables 61
Annex D (informative) Dimensions of steel, copper and
plastic pipes 62
Annex E (informative) Definition of “non-combustible”, “limited
combustibility”, Class O (national class), Class 1 (national class), Class A
(European class) and Class B (European Class). 64
Annex F (normative) Method for assessing the system load for
refrigeration pipe-work 65
Annex G (informative) Calculation of economic insulation
thickness 67
Annex H (normative) Non-standard pipe diameters and
plastic pipes 68
Annex I (normative) Calculations undertaken to show compliance
with this standard 71
Bibliography 72
List of figures
Figure G.1 – Economic thickness 67
List of tables
Table 1 – Maximum permitted water vapour permeance in relation to
plant temperature at an ambient temperature of +20 °C (dry bulb) 8
Table 2 – Minimum insulation thickness for refrigeration applications
to control condensation and control heat gain on a high emissivity
outer surface (0.90) with an ambient temperature of +20 °C and a
relative humidity of 70% 11
to control condensation and control heat gain on a low emissivity
to control condensation and control heat gain on a high emissivity
© BSI 2009 • i

to control condensation and control heat gain on a low emissivity
Table 6 – Minimum insulation thickness for chilled and cold water
steel pipes to control condensation on a high emissivity outer
surface (0.9) with an ambient temperature of +25 °C and a relative
humidity of 80% 18
copper pipes to control condensation on a high emissivity outer
humidity of 80% 19
steel pipes to control condensation on a low emissivity outer
humidity of 80% 20
copper pipes to control condensation on a low emissivity outer
humidity of 80% 21
Table 10 – Indicative thickness of insulation for cooled and chilled
water systems to control heat gain – Low emissivity outer surfaces 22
Table 11 – Indicative thickness of insulation for cooled and chilled

water systems to control heat gain – High emissivity outer surfaces 23
Table 12 – Minimum insulation thickness for condensation control
on ductwork carrying chilled air in ambient conditions: indoor
still air temperature +25 °C, relative humidity 80%, dewpoint
temperature 21.3 °C 27
Table 13 – Indicative thickness of insulation for ductwork carrying
warm air to control heat loss 28
Table 14 – Indicative thickness of insulation for chilled and dual-
purpose ducting to control heat transfer 28
Table 15 – Indicative thickness of insulation for non-domestic heating
services to control heat loss – Low emisivity outer surfaces 29
Table 16 – Indicative thickness of insulation for non-domestic heating
services to control heat loss – High emisivity outer surfaces 30
Table 17 – Indicative thickness of insulation for non-domestic hot
water service areas to control heat loss – Low emissivity outer
surfaces 31
Table 18 – Indicative thickness of insulation for non-domestic hot
water service areas to control heat loss – High emissivity outer
surfaces 32
Table 19 – Indicative thickness of insulation for domestic heating and
hot water systems having low emissivity outer surfaces 35
Table 20 – Indicative thickness of insulation for domestic heating and
hot water systems having high emissivity outer surfaces 35
Table 21 – Minimum insulation thickness for process pipework and
equipment to control heat loss 39
Table 22 – Minimum insulation thickness to control the surface
temperature of a non-metallic surface with a surface emissivity
of 0.90 and design cold face temperature of 59 °C 42
temperature of a metallic surface with a surface emissivity of 0.05 and
design cold face temperature of 50 °C 44
temperature of a non-metallic surface with a surface emissivity
of 0.90 and design cold face temperature of 50 °C 46
ii • © BSI 2009
Table 25 – Heat loss from bare surfaces calculated in accordance with

BS EN ISO 12241:1998 (black steel pipes) 48
Table 26 – Heat loss from bare surfaces calculated in accordance
with BS EN ISO 12241:1998 (copper pipes – commercial grade, scoured
to a shine) 49
Table 27 – Heat loss from bare surfaces calculated in accordance with
BS EN ISO 12241:1998 (copper pipes – oxidized) 50
Table 28 – Minimum insulation thickness to protect steel pipes against
freezing – Selected industrial process conditions 52
Table 29 – Minimum insulation thickness required to give
protection against freezing – Selected commercial and institutional
conditions 53
Table 30 – Minimum insulation thickness to protect against freezing –
Selected domestic cold water systems (12 hour period) 54
Table 31 – Minimum insulation thickness to protect against freezing –
Selected domestic cold water systems (8 hour period) 55
Table A.1 – Variables assumed in development of methodology for
process pipework tables 57
Table A.2 – Reference thermal conductivities of insulation 58
Table B.1 – Surface emissivity (!) 59
Table B.2 – Default data for use in
BS EN ISO 12241:1998 calculations 60
Table C.1 – Summary of criteria used to establish the tables 61

Table D.1 – Outside diameter of steel pipe (from BS EN 10220) 63
Table D.2 – Outside diameter of copper pipe (from BS EN 1057) 63
Summary of pages
This document comprises a front cover, an inside front cover,
pages i to iv, pages 1 to 74, an inside back cover and a back cover.
© BSI 2009 • iii

Foreword
Publishing information
This British Standard is published by BSI and came into effect on
1 January 2009. It was prepared by Technical Committee B/540/7,
Thermal insulation for equipment and industrial applications. A list
of organizations represented on this committee can be obtained on
request to its secretary.
Supersession
This British Standard supersedes BS 5422:2001, which is withdrawn.
Relationship with other publications

The methods used in this standard to calculate heat transfer are in
accordance with BS EN ISO 12241:1998.
Information about this document

The start and finish of text introduced or altered by Corrigendum No. 1
is indicated in the text by tags .
The Non-domestic Technical Handbook [1] and the Domestic Technical
Handbook [2] cite BS 5422:2001 as a means of demonstrating

compliance with certain requirements of the Building (Scotland)
Regulations 2004 [3]; this British Standard does not replace the 2001
edition for this purpose.
All tables of insulation thicknesses have been reviewed in the light of
current working practices. The assumptions on which the tables are
based are given in each case.
The “environmental insulation thickness” tables have been revised to
take account of the increased awareness of the importance of limiting
carbon dioxide (CO2) emissions, whilst taking account of practical
factors, current materials and energy costs. Annex A shows the way in
which the environmental thickness was derived.
Specific guidance is included in Annex H for plastic pipes, in recognition
of the increase in their use. Guidance for non-standard pipe sizes is also
included in Annex H.
The standard is not prescriptive, and recognizes that there are many
reasons why the insulation of pipes, tanks, vessels, ductwork and
equipment may be required. It is therefore important that a specifier
states the criteria, specific Clause or reference in this standard in any
specification.
Presentational conventions
The provisions of this standard are presented in roman (i.e. upright)
type. Its requirements are expressed in sentences in which the
principal auxiliary verb is “shall”.
Commentary, explanation and general informative material is presented
in smaller italic type, and does not constitute a normative element.
Contractual and legal considerations

This publication does not purport to include all the necessary provisions
of a contract. Users are responsible for its correct application.
Compliance with a British Standard cannot confer immunity from
legal obligations.
iv • © BSI 2009
Introduction
In any single application for pipework and equipment, thermal insulation
material can perform a variety of functions simultaneously, including:
a) conserve energy for both cooled and heated systems;
b) retard freezing of contents;
c) control condensation on refrigerated, chilled or cold surfaces;
d) protect personnel from exposure to extremes of surface
temperature;
e) control process or service temperatures;
f) limit effects of system on indoor building temperature.
Even within the range listed, consideration should be given to
sub-sectors of these functions.
For example, energy conservation can be driven by two distinct
considerations. The first, and more traditional, reason for seeking
energy saving is to save cost. The second, and more recent, reason
for seeking energy saving is to minimize carbon dioxide emissions
from the associated power source. Although any insulation measure
has desired effects in both of these areas simultaneously, the extent
of insulation that can be justified varies with the comparative costs

of energy on the one hand, and alternative costs of carbon dioxide
emission abatement on the other. Since thermal insulation of
pipework and equipment represents one of the most cost-effective
ways available of limiting carbon dioxide emissions, this standard
highlights a series of thicknesses within its core tables, which have
been calculated in accordance with environmental principles as
outlined in Annex A.
Although the tables provided in this standard offer a simple method
of determining the minimum thickness levels, their use will require
the basic information outlined in Clause 4 and, in some cases,
additional information may be required. This specific information is
outlined in the clauses pertaining to specific applications.
Where information such as the thermal conductivity of the chosen
insulation material or the pipe diameter do not conform to the
categories highlighted in the relevant tables, it is possible to
interpolate between either columns or rows where the margin of
error is not likely to be critical. For greater accuracy, and where the
application parameters differ from those covered within the scope
of a Table (e.g. different ambient air temperature), the specifier
should calculate from first principles by using methods set out in
BS EN ISO 12241:1998 and the Annexes to this standard.
The default values for use in relation to this standard are given in
Annex B, the criteria used to establish the tables are summarized
in Annex C, and the standard diameters of pipes considered are given
in Annex D.
© BSI 2009 • 1
1 Scope
This British Standard describes a method for specifying requirements
for thermal insulating materials on pipes, tanks, vessels, ductwork
and equipment for certain defined applications and conditions
within the temperature range –40 °C to +700 °C. It also specifies some
physical requirements for the insulating materials. It is intended for
use by designers, specifiers, contractors and manufacturers of thermal
insulation.
This British Standard does not apply to pipelines that are embedded
underground, nor does it refer to the insulation of building construction.
2 Normative references
The following referenced documents are indispensable for the
application of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the
referenced document (including any amendments) applies.
BS 476-4, Fire tests on building materials and structures –
Part 4: Non-combustibility test for materials

Part 6: Method of test for fire propagation for products
BS 476-7:1997, Fire tests on building materials and structures –
Part 7: Method of test to determine the classification of the surface
spread of flame of products
Part 11: Method for assessing the heat emission from building
materials
BS 3177, Method for determining the permeability to water vapour of
flexible sheet materials used for packaging
BS 4370-2:1993+A2:2001, Methods of test for rigid cellular
materials – Part 2: Methods 7 to 9
BS EN ISO 12241:1998, Thermal insulation for building equipment and
industrial installations – Calculation Rules
3 Terms and definitions

For the purposes of this British Standard, the following definitions
apply.
3.1 chilled water
water that has been processed through cooling plant (typically 0 °C
to +10 °C)
3.2 cold water
water delivered from the mains or natural supply
3.3 economic thickness
thickness of insulation that minimizes the total cost (investment and
running costs) over a chosen evaluation period
2 • © BSI 2009
3.4 environmental thickness

thickness of insulation that balances the cost of the interest payments
incurred to insulate the system against the cost of the energy saved as
a consequence (see Annex A)
3.5 evaluation period
time over which the heat transfer through insulated surfaces is to be
calculated, e.g. to carry out frost protection or economic thickness
calculations
3.6 finishing materials
materials used to cover the insulation, whether pre-applied or applied
on site
3.7 insulation thickness
thickness of insulating material, excluding any finish or covering
3.8 maximum service temperature
highest temperature to which a thermal insulation or other material
may be exposed and at which it will continue to function within the
specified limits of its performance
3.9 minimum service temperature
lowest temperature to which a thermal insulation or other material
may be exposed and at which it will continue to function within the

specified limits of its performance
3.10 pre-applied
applied to the insulation prior to delivery to the point of use
3.11 termination point
point at which the thermal insulation applied to a pipe, duct or vessel
is terminated, e.g. at a valve or flange, or where traversing a wall or
ceiling
3.12 water vapour barrier
layer intended to control water vapour diffusion
NOTE In practice it is impossible to achieve a total vapour barrier with a
single layer.
3.13 water vapour permeance

density of water vapour flow rate divided by the water vapour pressure
difference between the two surfaces of the specimen during the test
3.14 water vapour resistance
reciprocal of water vapour permeance
3.15 water vapour retarder
material which reduces water vapour diffusion
© BSI 2009 • 3
4 Application of this standard

A specification produced in accordance with this British Standard shall
specify only those elements of the standard to which conformity is
required for a specific application. A specification shall be deemed to
conform to this British Standard if it makes reference to the clauses
and tables within this standard that pertain to the application being
specified. The selection of materials and the insulation thickness to be
specified shall be determined according to the intended function of
the insulation.
The specification shall state the prime purpose of the insulation and
shall specify the performance requirements for the selected insulation
system. The specification shall identify the minimum performance
requirements for each application or parameter. The application or
parameter that requires the greatest thickness of insulation shall take
precedence.
The performance requirements shall be specified in accordance with
the appropriate clauses and tables of this standard, which shall be
determined from the following factors:
a) system operating temperature;
b) design ambient air temperature;

c) relative humidity of the ambient air;
d) air velocity;
e) location of the plant (indoors or outdoors);
f) pipe diameter (or flat surface dimensions);
g) orientation of pipes (horizontal or vertical);
h) vertical dimensions of flat surfaces;
i) emissivity of outer surface.
For refrigerated, chilled and other cold applications, where applicable,
water vapour permeance or resistance of the complete insulation system
(including water vapour barrier where applied) shall also be specified in
accordance with the appropriate clauses and tables of this standard.
5 General requirements
5.1 Physical characteristics

The specifier shall specify the required performance and physical
characteristics of the materials, including finishing materials, whether
pre-applied or applied on site, in accordance with the appropriate
British Standard.
The manufacturer or supplier shall declare the performance and
physical characteristics of the materials in accordance with the
appropriate British Standard.
To help ensure that the insulation material specified is suitable for the
intended application, consideration shall be given as to whether:
a) the material contains substances that will support pests or
encourage the growth of fungi;
4 • © BSI 2009
b) the material gives off an objectionable odour at the temperatures

at which it is to be used;
NOTE 1 Transient effects during the initial period of use may
generally be ignored.
c) the material suffers permanent structural or physical
deterioration as a result of contact with moisture;
d) the material suffers structural or physical deterioration as a result
of use at specified operating temperatures;
e) the material is suitable for specified conditions of use without the
physical properties falling outside the tolerances allowed in the
appropriate British Standard for the material;
f) materials in contact are compatible and do not cause corrosion or
degradation under normal site conditions;
g) the material and its method of application constitutes a known
risk to health during application or use.
NOTE 2 Reference should be made to BS 5970 for health hazards
when selecting, storing or removing insulation. Attention is also
drawn to the latest edition of COSHH Regulations [4].
5.2 Installation requirements

NOTE Guidance on the correct application of insulation and associated
attachments is given in BS 5970.
5.3 Thermal conductivity
5.3.1 General
Manufacturers or suppliers of insulating materials shall supply
declared thermal conductivity values based on results of tests carried
out in accordance with the appropriate British or European Standards.
Thermal conductivity shall be expressed in Watts per square metre
for 1 m thickness and a temperature difference of 1 K.
NOTE 1 The values quoted for thermal conductivity relate to the
appropriate insulation mean temperature, which is defined as the mean
of the operating temperature of the system added to the temperature of
the outer surface of the insulation system.
NOTE 2 In terms of unit symbols thermal conductivity should be
expressed as W/(m · K).
The contractor shall state the manufacturer’s declared values of thermal
conductivity for each material proposed. These declared values shall be
appropriate to the mean temperature of the applied insulation.
5.3.2 Composite insulation

When two or more layers of dissimilar insulating material are to
be used, the contractor shall provide the declared value of thermal
conductivity for each layer under the appropriate temperature
conditions. The thickness of each layer shall also be stated.
© BSI 2009 • 5
5.3.3 Design value of thermal conductivity and thermal bridges

Additional allowances shall be made to ensure that the specified
performance is achieved where system inefficiencies are created
through the ageing of the product, or by the presence of valves or
other in-line or ancillary fittings.
NOTE 1 Guidance is given in BS EN ISO 12241:1998.
NOTE 2 To limit heat transfer through supports, load-bearing insulating
material should be used on the pipe or vessel between the support and the
surface to be insulated. If a water vapour barrier is required, the sealing of
the load-bearing material should conform to the same requirements as the
basic insulation and be fitted so that the integrity of the vapour barrier of
the system is maintained. Where the heat transfer through the supports
does not need to be limited but a water vapour barrier is required, the
edges of the insulation, where interrupted at the support, should be
sealed to maintain the effectiveness of the vapour barrier.
Other structural elements, such as stiffening rings, should be insulated
externally to reduce thermal bridging.
5.4 Temperature limitations

The manufacturer or supplier shall state the maximum or minimum
service temperatures of the products specified, as appropriate.

If the temperature of the surface to be insulated is above the limiting
temperature of the preferred main insulating material, composite or
alternative insulation shall be specified. Where composite insulation is
specified, the thickness of each layer shall be calculated to ensure that
the interface temperature between the two materials does not exceed
the limiting temperature for the material of the outer layer.
5.5 Thickness
If thicknesses are required other than those given in the tables in the
appropriate section, or bases needed other than those from which
they were derived, the specification shall state the thickness required
or the bases to be used in the calculation.
If the thicknesses derived using this standard do not correspond
with commercially available thicknesses, the nearest higher available
thickness shall be used.
In multilayer applications, where material thicknesses are rounded up
to suit available thicknesses, a further calculation in accordance with
BS EN ISO 12241:1998 shall be made to ensure that each interface
temperature is below the maximum service temperature of the
materials involved.
NOTE 1 Additional allowances should be made for heat transfer through
joints, valves and other fittings when determining insulation thickness in
accordance with BS EN ISO 12241:1998.
NOTE 2 Thicknesses given in the tables within this standard are
specifically calculated against the criteria noted in each Table. Adopting
these thicknesses may not necessarily satisfy other design requirements.
6 • © BSI 2009
5.6 Vapour barrier – Permeance requirements

NOTE 1 Condensation of water vapour will occur on a surface that is at
a temperature below the atmospheric dew point temperature. Moisture
can be deposited within the insulating material and on the insulated
metal surface. Where the insulated surface is likely to be at or below the
dew point temperature during any part of its operating cycle, an effective
vapour barrier should be applied on the warmer face of the insulation to
avoid deposition of moisture within the insulating system. The presence
of water within an insulation system can reduce thermal effectiveness and
lead to corrosion of metal components.
For the purpose of this standard an effective vapour barrier shall
be deemed to be one that meets the water vapour permeance
requirements given in this subclause.
Different levels of water vapour permeance shall be specified according
to the type of application. Where the insulating material itself does
not conform to the water vapour permeance requirement, a “vapour
barrier” on the outside (warm side) of the insulation shall be used.
The vapour barrier shall take the form of a coating or sheet material.
Any joints in the coating or sheet material or in the insulating material
itself, where it is providing the water vapour permeance requirement,
shall be fully sealed.
NOTE 2 This is to ensure that the vapour permeance performance is

maintained continuously in the system as installed.
Particular care shall be taken at termination points. The external
vapour barrier, where required, shall be pre-applied or applied before
the fluid in the pipe, duct, or vessel is cooled.
When a vapour barrier is used, the system as installed, shall have a fire
performance at least equal to that specified in 6.2.2, 7.2.2, 8.2.2, 9.2.2
and 10.2.2 as appropriate to the type of application.
The water vapour permeance of flexible sheets used as external
vapour barriers shall be assessed in accordance with the method
given in BS 3177. The test conditions, e.g. temperate or tropical,
and the thickness of the test specimen shall be stated. Where the
apparatus for the method in BS 3177 is unsuitable because of the
thickness of the test specimen, BS 4370-2:1993+A2, method 8 shall
be used. The water vapour permeance of the insulated system shall
be selected according to the relationship between the cold surface
temperature of the plant and the temperature difference, in degrees
centigrade (°C), between the plant temperature and ambient
temperature as indicated in Table 1.
NOTE 3 The permeance values given in Table 1 are applicable at an
ambient temperature of 20 °C and a relative humidity of 70%, and other
environmental conditions resulting in an equal or lesser partial vapour
pressure difference. In order to calculate the partial vapour pressure
difference, the internal temperature should be assumed to be equal to
the plant temperature and the internal relative humidity to be 100%. In
situations where the environmental conditions are normally 25 °C and a
relative humidity of 80% the vapour barrier permeance is selected from
Table 1 by subtracting 10 °C from the plant operating temperature.
NOTE 4 Additional guidance may be found in BS EN 14114, which sets
out a methodology for the calculation of water vapour transmission
through a water vapour barrier.
© BSI 2009 • 7
Table 1 Maximum permitted water vapour permeance in relation to plant temperature at an ambient
temperature of +20 °C (dry bulb)
Temperature of plant (cold surface) Water vapour permeance of barrier

°C g/(s · MN)
10 0.050
5 0.015
0 0.010
−5 0.004
−10 0.002
−15 0.0015
−20 to −40 0.0010
Where it is necessary to add additional claddings to an external vapour

barrier, e.g. to provide weather or mechanical protection, the specifier
shall state the type of finish to be applied. The installer shall ensure that
the application of any additional coverings does not damage the vapour
barrier during installation and that it is unlikely to cause damage to, or
degrade the performance of, the vapour barrier in service.
NOTE 5 For further details see BS 5970.
5.7 Tests on physical properties

Where particular physical properties are required the specifier shall
nominate the appropriate British Standard test methods. Only where
no suitable British Standard test methods exist shall the specifier
authorize the use of an alternative test method to determine whether
the required level of performance is met.
6 Refrigeration applications
6.1 Information to be supplied by the specifier

The specifier shall supply details of the intended function and
performance requirements of the application, and the materials to be
used, in accordance with Clause 4.
NOTE In addition to the parameters outlined in Clause 4, items such as
specific heat capacity and mass flow rates of fluids may also be required
under certain circumstances, particularly where calculating from first
principles using BS EN ISO 12241:1998. However, these additional
parameters are not required for the use of the tables contained in this
standard.
6.2.1 General
The physical characteristics of the insulating material including
finishing materials and vapour barriers, whether applied during
manufacture or on site, shall conform to 5.1, 6.2.2 and 6.2.3.
8 • © BSI 2009
6.2.2 Fire performance

Insulation materials and systems used for refrigeration shall conform
to the following requirements.
NOTE 1 Attention is drawn to the applicable requirements of the
Building Regulations [5], the Building (Scotland) Regulations [3] and the
Building Regulations (Northern Ireland) [6].
Insulation systems on pipework or ductwork traversing a fire-resisting
division shall maintain the level of fire resistance of the wall, floor or
cavity barrier through which they pass.
NOTE 2 In the event of a fire some insulation systems can generate
appreciable quantities of smoke and toxic fumes. Consideration should
be given to the choice of materials bearing in mind their location, e.g.
enclosed areas or adjacent to air ducts through which the smoke or fumes
may spread.
In buildings other than dwellings, the complete assembly of installed
insulation materials (whether faced or unfaced) shall be Class O
(national class) or better.
In dwellings, the complete assembly of installed insulation materials
(whether faced or unfaced) shall be Class 1 (national class) or better.
For faced or over-clad materials, which are not Class 1 (national class)
or better when tested without the facing, particular care shall be
taken with the facing to ensure that all joints and seams, etc., are
fitted correctly, so that the underlying insulation is not left exposed to
a potential ignition source. Where the complete assembly is liable to
mechanical damage in use, the final finish shall be sufficiently strong
to ensure that the insulation does not become exposed.
If there is a potential hazard from contamination by oil or other
flammable chemicals, a suitably resistant finish, e.g. a metal sheet
or appropriate non-absorbent coating, shall be applied over the
vulnerable areas. The lapped joints of sheet finishes shall be arranged
to shed contaminating fluids away from the insulating material.
In underground or windowless buildings, the underlying thermal
insulation material used for external insulation of ventilation
ductwork or pipes greater than 100 mm nominal bore shall itself be
of “limited combustibility” or be “non-combustible”. In addition, the
complete assembly of installed insulation materials (whether faced or
unfaced) shall be Class O (national class) or better.
NOTE 3 See Annex E for an explanation of “limited combustibility”,
“non-combustible”, Class O and Class 1 (national classes) and Classes A1,
A2, B, C, D, E or F (European classes).
6.2.3 Water vapour barrier – Permeance requirements

Insulation materials and systems used for refrigeration shall be
installed in accordance with and shall conform to the permeance
requirements specified in 5.6.
When tested in accordance with BS 3177 or BS 4370-2, as appropriate,
the permeance of the material used as a vapour barrier shall not
exceed the values given in Table 1 for the appropriate temperature of
the plant.
© BSI 2009 • 9
6.3 Insulation thickness – Protection against

condensation and control of heat gain
6.3.1 In the absence of specific instructions from the specifier, the insulation
thickness shall be not less than that given in Table 2 to Table 5, as
appropriate.
6.3.2 Where the contribution of the heat gain of the distribution pipe work
does not exceed 5% of the total heat load, the thicknesses given
in Table 2 to Table 5 to control condensation shall also be used to
limit heat transfer. Where the contribution of the heat gain of the
distribution pipe work does exceed 5%, the thickness of insulation
shall be increased such that the heat gain of the distribution pipe is
reduced to less than 5%. Calculating distribution pipe-work heat gains
shall be carried out in accordance with Annex F.
6.3.3 Thicknesses of insulation for pipe diameters not shown in Table 2 to
Table 5, and for all plastic pipes, shall be determined in accordance
with Annex H.
10 • © BSI 2009
Table 2 Minimum insulation thickness for refrigeration applications to control condensation and control heat gain on a high emissivity outer
surface (0.90) with an ambient temperature of +20 °C and a relative humidity of 70%
Outside Insulation thickness (mm)

diameter of
steel pipe on
which insulation t=0 t = –10 t = –20 t = –30 t = –40
thickness has
been based
BRITISH STANDARD
(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050
21.3 5 7 9 11 8 11 14 16 10 14 18 22 13 18 22 27 15 21 26 31
33.7 5 8 10 12 8 12 15 18 11 16 20 24 14 20 25 30 17 23 29 35
60.3 6 8 11 13 9 13 17 21 13 18 23 28 16 22 29 34 19 27 34 41
114.3 6 9 12 15 10 15 19 24 14 20 26 32 18 25 33 40 21 30 39 47
168.3 7 10 13 16 11 16 21 25 15 22 28 34 19 27 35 43 23 33 42 51
273.0 7 10 13 17 12 17 22 27 16 23 30 37 20 29 38 47 24 35 46 56
508.0 7 11 14 18 12 18 24 29 17 25 33 40 22 32 41 51 26 38 50 62
610.0 8 11 15 18 12 18 24 30 17 25 33 41 22 32 42 52 27 39 51 63
Flat surfaces 8 11 15 18 12 18 24 30 17 26 34 43 22 33 44 55 27 40 54 67
Key
t = temperature of contents (°C)
( = thermal conductivity at mean temperature of insulation [W/(m · K)]
NOTE Thicknesses given are calculated specifically against the criteria noted in the table. These thicknesses may not satisfy other design requirements. In
situations where the ambient air temperature is greater than 20 °C and/or the relative humidity exceeds 70%, these thicknesses will not be sufficient to control
condensation.
© BSI 2009 •
BS 5422:2009
11
Table 3 Minimum insulation thickness for refrigeration applications to control condensation and control heat gain on a low emissivity outer

diameter of
steel pipe on
BS 5422:2009
12 • © BSI 2009
thickness has
been based
(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050
21.3 9 13 16 20 14 20 26 31 19 27 35 42 24 34 44 53 28 41 52 64
33.7 10 14 19 23 16 23 30 36 22 31 40 49 27 39 50 61 33 47 60 73
60.3 12 17 22 27 19 27 35 43 26 37 48 59 33 47 60 73 39 56 72 88
114.3 14 20 27 33 23 33 43 52 31 45 58 71 39 57 73 89 47 68 88 107
168.3 16 23 30 36 25 37 48 59 35 50 65 80 44 64 82 101 53 76 99 121
273.0 17 26 34 41 29 42 55 67 40 58 75 92 50 73 95 116 61 88 114 140
508.0 20 30 39 49 33 49 65 80 46 68 89 110 59 87 113 139 72 105 137 167
610.0 21 31 41 51 35 52 68 84 49 71 94 115 62 91 119 146 75 110 144 176
Flat surfaces 20 30 40 50 34 51 68 85 48 72 96 119 62 93 123 154 76 113 151 188
Key
situations where the ambient air temperature is greater than 20 °C and/or the relative humidity exceeds 70%, these thicknesses will not be sufficient to control
condensation.
BRITISH STANDARD
Table 4 Minimum insulation thickness for refrigeration applications to control condensation and control heat gain on a high emissivity outer

diameter of
steel pipe on
thickness has
been based
BRITISH STANDARD
(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050
21.3 10 14 17 21 13 19 24 28 17 23 29 35 20 28 35 42 23 32 41 49
33.7 11 15 19 23 15 21 26 32 19 26 33 40 22 31 39 47 26 36 46 55
60.3 12 17 22 26 17 24 30 36 21 30 38 46 26 36 45 55 30 42 53 63
114.3 13 19 25 30 19 27 34 42 24 34 44 53 29 41 53 63 34 48 61 74
168.3 14 20 26 32 20 29 37 45 26 37 47 57 31 44 57 69 36 52 66 80
273.0 15 22 28 35 21 31 40 49 27 40 51 63 33 48 62 76 39 57 73 88
508.0 16 23 30 37 23 33 44 54 29 43 56 69 36 53 69 84 43 62 81 99
610.0 16 24 31 38 23 34 44 55 30 44 58 71 37 54 70 86 44 64 83 102
Flat surfaces 16 24 32 39 23 35 46 58 31 46 61 76 38 57 76 94 45 68 90 113
Key
situations where the ambient air temperature is greater than 25 °C and/or the relative humidity exceeds 80%, these thicknesses will not be
sufficient to control condensation.
© BSI 2009 •
BS 5422:2009
13
Table 5 Minimum insulation thickness for refrigeration applications to control condensation and control heat gain on a low emissivity outer

diameter of
steel pipe on
BS 5422:2009
14 • © BSI 2009
thickness has
been based
(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050
21.3 19 28 36 43 27 39 50 61 35 50 64 79 42 60 78 96 49 71 92 113
33.7 22 32 41 50 31 45 58 70 40 57 74 90 48 69 90 109 57 81 105 129
60.3 27 38 49 60 37 53 69 84 48 68 88 107 58 83 107 130 68 97 125 153
114.3 32 46 60 73 45 65 84 102 58 83 107 131 70 101 130 158 82 118 152 185
168.3 36 51 67 82 51 73 94 115 65 93 121 147 79 113 146 178 93 133 171 209
273.0 40 59 77 94 58 84 109 133 75 108 140 170 91 131 169 206 107 154 198 242
508.0 47 69 91 112 68 99 130 159 88 128 167 205 108 157 203 249 127 184 239 291
610.0 49 73 95 117 71 104 136 167 93 135 176 216 113 165 214 262 134 194 252 308
Flat surfaces 49 73 97 122 72 107 143 179 95 142 189 236 117 176 234 292 140 210 280 349
Key
situations where the ambient air temperature is greater than 25 °C and/or the relative humidity exceeds 80%, these thicknesses will not be
sufficient to control condensation.
BRITISH STANDARD
7 Chilled and cold water applications

principles using BS EN ISO 12241:1998. However, these additional parameters
are not required for the use of the tables contained in this standard.
7.2.1 General
The physical characteristics of the insulating material, including fixing
and finishing materials whether pre-applied or applied on site, shall
conform to 5.1, 7.2.2 and 7.2.3.

Insulation materials and systems used for chilled and cold water
applications shall conform to the following requirements.
may spread.
The complete assembly of installed insulation materials (whether
faced or unfaced) shall be Class O (national class) or better.
The insulation material itself (i.e. tested without any facing) shall be
Class 1 (national class) or better.
© BSI 2009 • 15

Insulation materials and systems used for chilled and cold water
applications shall be installed in accordance with and shall conform to
the permeance requirements specified in 5.6.
the permeance of the material used as a vapour barrier shall not exceed
the values given in Table 1 for the relevant temperature of the plant.
7.3 Insulation thickness
7.3.1 Protection against condensation

In the absence of specific instructions from the specifier, the
insulation thickness shall be not less than that given in Table 6 to
Table 9 as appropriate.
Thicknesses of insulation for pipe diameters not shown in Table 6 to
with Annex H.
Control of heat gain to cooled and chilled water pipes

7.3.2
In the absence of specific instructions from the specifier, and where
the cooling load is not proven to be less than 5%, the insulation
thickness shall be not less than that given in Table 10 or Table 11, as
appropriate.
The cooling load shall be calculated in accordance with Annex F.
Thicknesses of insulation for pipe diameters not shown in Table 10 and
with Annex H.
For an intermediate pipe diameter not listed in Table 10 and Table 11,
compliance calculations shall use the nearest larger diameter listed.
For pipes or vessels of diameter greater than 273 mm, the items in
Table 10 and Table 11 shall be assumed to be 273 mm for calculation
purposes.
To show compliance with the requirements of Table 10 and Table 11,
insulation thicknesses shall be calculated using standardized
assumptions: horizontal pipe at t °C in still air at 25 °C, emissivity of
outer surface of insulated system as specified.
NOTE 1 Guidance on cooled ducts is given in Table 12 and Table 14.
NOTE 2 Attention is drawn to the energy performance requirements of
Approved Document L2B [7], Technical Booklet F2 [8] and Non-domestic
Technical Handbook [1], Section 6.
The thicknesses of insulation specified in Table 10 and Table 11 to limit
heat transfer meet or improve upon the minimum requirements of
Approved Documents L2B [7] and Technical Booklet F2 [8]. However,
these thicknesses of insulation might not comply with future revisions
of the Building Regulations [5] and the Building Regulations (Northern
Ireland) [6], and the current versions of these documents should be
consulted to ensure compliance.
Section 6 of the Non-domestic Technical Handbook [1] retains references
to guidance given in BS 5422:2001 as a means of showing compliance.
16 • © BSI 2009
NOTE 3 It should be noted that Building Regulations [3], [5], [6] provide
minimum requirements for heat transfer to reduce energy use. The use
of greater thicknesses of insulation can provide substantial financial
and environmental benefits. Additional considerations might include
acoustic performance, aesthetic qualities, fire properties, durability and
thermal performance for reasons other than energy reduction; such as
process control, control of condensation, internal building environment,
surface temperature and freezing. This standard provides guidance on fire
properties and thermal performance only.
© BSI 2009 • 17
Table 6 Minimum insulation thickness for chilled and cold water steel pipes to control condensation on a high emissivity outer surface (0.9) with an
ambient temperature of +25 °C and a relative humidity of 80%
! = 0.9
Outside diameter of steel t = 10 t=5 t=0
BS 5422:2009
pipe on which insulation Insulation thickness (mm) Insulation thickness (mm) Insulation thickness (mm)
18 • © BSI 2009
thickness has been based
(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05
17.2 6 7 8 9 10 11 12 8 9 10 12 13 15 16 9 11 13 15 16 18 20
21.3 6 7 8 9 10 11 12 8 9 11 12 14 15 17 10 12 14 15 17 19 21
26.9 6 7 9 10 11 12 13 8 10 12 13 15 16 18 10 12 14 16 18 20 22
33.7 6 8 9 10 11 13 14 9 10 12 14 15 17 19 11 13 15 17 19 21 23
42.4 7 8 9 11 12 13 14 9 11 13 14 16 18 19 11 14 16 18 20 22 24
48.3 7 8 9 11 12 13 15 9 11 13 15 17 18 20 12 14 16 19 21 23 25
60.3 7 8 10 11 13 14 15 10 12 14 15 17 19 21 12 15 17 19 22 24 26
76.1 7 9 10 12 13 15 16 10 12 14 16 18 20 22 12 15 18 20 23 25 28
88.9 7 9 10 12 13 15 16 10 12 14 17 19 21 23 13 16 18 21 24 26 29
114.3 8 9 11 12 14 16 17 10 13 15 17 19 22 24 13 16 19 22 25 27 30
139.7 8 9 11 13 14 16 18 11 13 15 18 20 22 25 14 17 20 23 25 28 31
168.3 8 10 11 13 15 16 18 11 13 16 18 21 23 25 14 17 20 23 26 29 32
219.1 8 10 12 14 15 17 19 11 14 16 19 21 24 26 14 18 21 24 27 30 33
273 8 10 12 14 16 17 19 12 14 17 19 22 25 27 15 18 22 25 28 31 35
323.9 8 10 12 14 16 18 20 12 14 17 20 22 25 28 15 19 22 25 29 32 35
355.6 8 10 12 14 16 18 20 12 15 17 20 23 25 28 15 19 22 26 29 32 36
406.4 9 10 12 14 16 18 20 12 15 18 20 23 26 28 15 19 23 26 30 33 36
457 9 11 13 15 16 18 20 12 15 18 21 23 26 29 16 19 23 26 30 33 37
508 9 11 13 15 17 19 21 12 15 18 21 24 26 29 16 19 23 27 30 34 37
610 9 11 13 15 17 19 21 12 15 18 21 24 27 30 16 20 24 27 31 35 38
Key
NOTE Thicknesses given are calculated specifically against the criteria noted in the table. These thicknesses may not satisfy other design requirements. In situations
where the ambient air temperature is greater than 25 °C and/or the relative humidity exceeds 80%, these thicknesses will not be sufficient to control condensation.
BRITISH STANDARD
Table 7 Minimum insulation thickness for chilled and cold water copper pipes to control condensation on a high emissivity outer surface (0.9) with an
! = 0.9
Outside diameter of t = 10 t=5 t=0
copper pipe on Insulation thickness (mm) Insulation thickness (mm) Insulation thickness (mm)
which insulation thickness
has been based (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05
BRITISH STANDARD
(mm)
10 5 6 7 8 9 9 10 7 8 9 10 12 13 14 8 10 11 13 14 16 17
12 5 6 7 8 9 10 11 7 8 10 11 12 13 14 9 10 12 13 15 16 18
15 5 7 8 9 10 10 11 7 9 10 11 13 14 15 9 11 13 14 16 17 19
22 6 7 8 9 10 11 12 8 10 11 13 14 15 17 10 12 14 16 17 19 21
28 6 7 9 10 11 12 13 8 10 12 13 15 16 18 10 12 15 16 18 20 22
35 6 8 9 10 11 13 14 9 10 12 14 16 17 19 11 13 15 17 19 21 23
42 7 8 9 11 12 13 14 9 11 13 14 16 18 19 11 14 16 18 20 22 24
54 7 8 10 11 12 14 15 9 11 13 15 17 19 21 12 14 17 19 21 24 26
76.1 7 9 10 12 13 15 16 10 12 14 16 18 20 22 12 15 18 20 23 25 28
108 7 9 11 12 14 15 17 10 13 15 17 19 21 23 13 16 19 22 24 27 30
Key
© BSI 2009 •
BS 5422:2009
19
Table 8 Minimum insulation thickness for chilled and cold water steel pipes to control condensation on a low emissivity outer surface (0.05) with an
! = 0.05
Outside diameter of steel t = 10 t=5 t=0
BS 5422:2009
pipe on which insulation Insulation thickness (mm) Insulation thickness (mm) Insulation thickness (mm)
20 • © BSI 2009
thickness has been based
(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05
17.2 11 13 15 17 19 21 23 14 18 21 23 26 29 32 18 22 26 30 33 37 41
21.3 11 14 16 18 20 23 25 15 19 22 25 28 31 34 19 24 28 32 36 40 43
26.9 12 15 17 20 22 24 27 17 20 24 27 30 34 37 21 25 30 34 38 42 47
33.7 13 16 18 21 24 26 29 18 21 25 29 32 36 39 22 27 32 36 41 46 50
42.4 14 17 20 22 25 28 31 19 23 27 31 35 39 42 24 29 34 39 44 49 54
48.3 14 17 20 23 26 29 32 20 24 28 32 36 40 44 25 30 36 41 46 51 56
60.3 15 18 22 25 28 31 34 21 26 30 34 39 43 47 27 32 38 44 49 54 60
76.1 16 20 23 27 30 33 37 22 27 32 37 42 46 51 28 35 41 47 53 58 64
88.9 17 20 24 28 31 35 38 23 29 34 39 44 48 53 30 36 43 49 55 61 67
114.3 18 22 26 30 34 37 41 25 31 36 42 47 52 57 32 39 46 53 60 66 73
139.7 19 23 27 32 36 40 44 26 32 38 44 50 55 61 34 41 49 56 63 70 77
168.3 20 24 29 33 38 42 46 28 34 40 46 52 58 64 36 44 51 59 67 74 82
219.1 21 26 31 36 40 45 49 30 37 43 50 56 63 69 38 47 55 64 72 80 88
273 22 27 33 38 43 48 53 31 39 46 53 60 67 74 40 50 59 68 77 85 94
323.9 23 29 34 39 45 50 55 33 41 48 55 63 70 77 42 52 62 71 80 90 99
355.6 24 29 35 40 46 51 56 34 41 49 57 64 72 79 43 53 63 73 82 92 101
406.4 25 30 36 42 47 53 58 35 43 51 59 67 74 82 45 55 65 76 86 95 105
457 25 31 37 43 49 54 60 36 44 52 61 69 77 85 46 57 68 78 88 98 109
508 26 32 38 44 50 56 62 37 45 54 62 71 79 87 47 58 69 80 91 101 112
610 27 33 40 46 52 59 65 38 47 56 65 74 83 91 49 61 73 84 95 106 117
Key
BRITISH STANDARD
Table 9 Minimum insulation thickness for chilled and cold water copper pipes to control condensation on a low emissivity outer surface (0.05) with an
! = 0.05
Outside diameter of t = 10 t=5 t=0
copper pipe on Insulation thickness (mm) Insulation thickness (mm) Insulation thickness (mm)
which insulation thickness
has been based (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.02 0.025 0.03 0.035 0.04 0.045 0.05
BRITISH STANDARD
(mm)
10 9 11 13 15 16 18 20 12 15 17 20 22 25 27 15 19 22 25 28 32 35
12 9 11 13 15 17 19 21 13 16 18 21 24 26 29 16 20 23 27 30 33 37
15 10 12 14 16 18 20 22 14 17 20 23 25 28 31 17 21 25 28 32 36 39
22 11 14 16 18 21 23 25 16 19 22 25 28 32 35 20 24 28 32 36 40 44
28 12 15 17 20 22 25 27 17 20 24 27 31 34 37 21 26 30 34 39 43 47
35 13 16 18 21 24 26 29 18 22 25 29 33 36 40 23 27 32 37 42 46 51
42 14 17 19 22 25 28 31 19 23 27 31 35 38 42 24 29 34 39 44 49 53
54 15 18 21 24 27 30 33 20 25 29 33 37 42 46 26 31 37 42 47 53 58
76.1 16 20 23 27 30 33 37 22 27 32 37 42 46 51 28 35 41 47 53 58 64
108 18 22 26 29 33 37 41 25 30 36 41 46 51 56 31 38 45 52 59 65 71
Key
© BSI 2009 •
BS 5422:2009
21
Table 10 Indicative thickness of insulation for cooled and chilled water systems to control heat gain – Low emissivity outer surfaces
Outside diameter Low emissivity surface finish (! = 0.05)

of steel pipe on Cooled water temperatures >10 °C Chilled water temperatures Chilled water temperatures
which insulation >4.9 °C to <10 °C of 0 °C to <4.9 °C
thickness has
BS 5422:2009
t = 10 t=5 t=0
22 • © BSI 2009
been based
(= (= (= (= (= Maximum ( = ( = (= (= (= Maximum ( = ( = (= (= (= Maximum
0.02 0.025 0.030 0.035 0.040 permissible 0.02 0.025 0.030 0.035 0.040 permissible 0.02 0.025 0.030 0.035 0.040 permissible
heat gain heat gain heat gain
(mm) Thickness of insulation (mm) (W/m) Thickness of insulation (mm) (W/m) Thickness of insulation (mm) (W/m)
17.2 6 8 11 15 20 2.48 7 11 15 20 28 2.97 9 13 18 24 33 3.47
21.3 7 9 12 16 21 2.72 8 12 16 21 28 3.27 9 14 19 25 34 3.81
26.9 7 10 13 17 22 3.05 9 13 18 23 30 3.58 11 15 21 27 36 4.18
33.7 8 11 14 18 23 3.41 10 14 19 24 31 4.01 12 17 22 29 38 4.6
42.4 9 12 15 19 24 3.86 11 15 20 25 32 4.53 13 18 24 31 40 5.11
48.3 9 13 16 20 25 4.11 12 16 21 26 33 4.82 14 19 25 32 41 5.45
60.3 10 13 16 20 25 4.78 13 17 22 27 34 5.48 15 20 26 33 42 6.17
76.1 11 14 17 21 26 5.51 14 18 23 28 35 6.3 16 22 28 35 44 6.7
88.9 11 14 18 21 26 6.17 14 19 24 29 36 6.9 17 22 29 35 43 7.77
114.3 12 15 19 22 27 7.28 15 19 24 29 35 8.31 18 24 30 36 44 9.15
139.7 12 15 19 22 27 8.52 16 20 25 30 36 9.49 19 25 31 37 45 10.45
168.3 12 15 19 22 26 9.89 16 20 25 30 36 10.97 20 25 32 38 46 11.86
219.1 12 15 19 22 26 12.27 16 21 25 30 36 13.57 20 26 32 38 45 14.61
273 12 16 19 22 26 14.74 16 21 26 30 36 16.28 21 26 32 38 45 17.48
Key
t = water temperature; standardised assumption for calculation purposes (°C)
! = emissivity of outer surface of insulated system
NOTE 1 Insulation thicknesses in this table have been calculated according to BS EN ISO 12241:1998 using standardized assumptions: horizontal pipe at t °C in
still air at 25 °C, emissivity of outer surface of insulated system as specified.
NOTE 2 Thicknesses derived solely against the criteria noted in this table may not necessarily satisfy other design requirements such as control of condensation.
NOTE 3 Heat gain relates to the specified thickness and temperature.
BRITISH STANDARD
Table 11 Indicative thickness of insulation for cooled and chilled water systems to control heat gain – High emissivity outer surfaces
Outside diameter High emissivity surface finish (! = 0.9)

of steel pipe on Cooled water temperatures >10 °C Chilled water temperatures Chilled water temperatures
which insulation >4.9 °C to <10 °C of 0 °C to <4.9 °C
thickness has
been based t = 10 t=5 t=0
(= (= (= (= (= Maximum ( = ( = (= (= (= Maximum ( = ( = (= (= (= Maximum
0.02 0.025 0.030 0.035 0.040 permissible 0.02 0.025 0.030 0.035 0.040 permissible 0.02 0.025 0.030 0.035 0.040 permissible
BRITISH STANDARD
heat gain heat gain heat gain

17.2 8 11 15 20 26 2.48 10 14 19 25 33 2.97 11 16 22 29 39 3.47
21.3 9 12 16 21 27 2.72 10 15 20 26 34 3.27 12 17 23 30 40 3.81
26.9 10 13 17 22 28 3.05 12 16 22 28 36 3.58 13 18 25 33 42 4.18
33.7 10 14 18 23 29 3.41 13 17 23 30 37 4.01 15 20 27 35 44 4.6
42.4 11 15 20 25 30 3.86 14 19 24 31 38 4.53 16 22 29 37 46 5.11
48.3 12 16 21 26 31 4.11 15 20 25 32 39 4.82 17 23 30 38 47 5.45
60.3 13 17 21 26 31 4.78 16 21 26 33 40 5.48 18 24 31 39 48 6.17
76.1 13 18 22 27 32 5.51 17 22 28 34 42 6.3 21 28 35 44 54 6.7
88.9 14 18 22 27 33 6.17 17 23 29 35 43 6.9 20 26 34 42 50 7.77
114.3 15 19 24 29 34 7.28 18 23 29 36 43 8.31 21 28 35 43 51 9.15
139.7 15 19 24 29 34 8.52 19 25 31 37 44 9.49 22 29 36 44 53 10.45
168.3 16 20 24 29 34 9.89 20 25 31 37 44 10.97 23 30 37 45 54 11.86
219.1 16 20 25 29 34 12.27 20 26 31 38 44 13.57 24 31 38 46 54 14.61
273 16 21 25 30 35 14.74 21 26 32 38 44 16.28 25 31 39 46 54 17.48
Key
t = water temperature; standardised assumption for calculation purposes (°C)
NOTE 1 Insulation thicknesses in this table have been calculated according to BS EN ISO 12241:1998 using standardized assumptions: horizontal pipe at t °C in
still air at 25 °C, emissivity of outer surface of insulated system as specified.
NOTE 2 Thicknesses derived solely against the criteria noted in this table may not necessarily satisfy other design requirements such as control of condensation.
© BSI 2009 •
BS 5422:2009
23
8 Central heating, air conditioning and

direct hot water supply installations in
non-domestic applications
Approved Documents L2A [9] and L2B [7], Technical Booklet F2 [8] and
Non-domestic Technical Handbook [1], Section 6.
The thicknesses of insulation specified in Table 13 to Table 18 to limit heat
transfer meet or improve upon the minimum requirements of Approved
Documents L2A [9] and L2B [7] and Technical Booklet F2 [8]. However,
these thicknesses of insulation might not comply with future revisions
of the Building Regulations [5] and the Building Regulations (Northern
Ireland) [6], and the current versions of these documents should be
consulted to ensure compliance.
Section 6 of the Non-domestic Technical Handbook [1] retains references
to guidance given in BS 5422:2001 as a means of showing compliance.
of greater thicknesses of insulation can provide substantial financial
and environmental benefits. Additional considerations might include
acoustic performance, aesthetic qualities, fire properties, durability and
thermal performance for reasons other than energy reduction; such as

process control, control of condensation, internal building environment,
surface temperature and freezing. This standard provides guidance on fire
properties and thermal performance only.

performance requirements of the application, and the materials to
be used, in accordance with Clause 4.
8.2.1 General
The physical characteristics of the insulating material, together with
adhesive, fixing, vapour barrier and finishing material, whether
pre-applied or applied on site, shall conform to 5.1, 8.2.2 and 8.2.3.

Insulation materials and systems used for central heating, air
conditioning and direct hot water supply installations in non-domestic
applications shall conform to the following requirements.
24 • © BSI 2009

may spread.
taken with the facing to ensure that all joints and seams, etc. are


If pipework or ductwork for central heating, air conditioning or direct
hot water supply systems is likely to have a surface temperature below
the dew point temperature, the insulation materials and system shall
conform to the permeance requirements and installation methods for
water vapour barriers detailed in 5.6.
Insulation materials and systems used for chilled air ductwork shall
be installed in accordance with and shall conform to the permeance
the permeance of the material used as a vapour barrier shall not
exceed the values given in Table 1 for the appropriate temperature of
the plant.
8.2.4 Maximum and minimum service temperature

The insulation selected shall be suitable for use at the maximum and
minimum temperatures of the intended application.
NOTE For example, pipes serving solar heated hot water systems may be
subject to peak temperatures of greater than 150 °C.
© BSI 2009 • 25
8.3.1 Minimum thickness of insulation to control condensation

on ductwork carrying chilled air
In the absence of specific instructions from the specifier, the insulation
thickness shall be not less than that given in Table 12.
Thicknesses of insulation for pipe diameters not shown in Table12, and
for all plastic pipes, shall be determined in accordance with Annex H.
8.3.2 Minimum thickness of insulation to control heat transfer

through ducts
In the absence of specific instructions from the specifier, the thickness
applied shall be not less than that given in Table 13 and Table 14.
For Table 13, insulation thicknesses shall be calculated according to
BS EN ISO 12241:1998 using standardized assumptions: horizontal duct
at 35 °C, with 600 mm vertical sidewall in still air at 15 °C, emissivity of
BS EN ISO 12241:1998 using standardized assumptions: horizontal duct

at 13 °C, with 600 mm vertical sidewall in still air at 25 °C, emissivity of
8.3.3 Minimum thickness of insulation to control heat loss

from pipes
NOTE The relevant thicknesses defined in Table 15, Table 16, Table 17 and
Table 18 have been derived using the methodology set out in Annex A.
thickness shall be as given in Table 15 to Table 18.
For an intermediate pipe diameter not listed in Table 15 and Table 16,
compliance calculations shall use the nearest larger diameter listed.
with Annex H.
For pipes or vessels of diameter greater than 273 mm, the items in
Table 15 to Table 18 shall be assumed to be 273 mm for calculation
purposes.
For Table 15 and Table 16, insulation thicknesses shall be calculated
according to BS EN ISO 12241:1998 using standardized assumptions:
horizontal pipe at t °C in still air at 15 °C, emissivity of outer
surface of insulated system as specified.
horizontal pipe at 60 °C in still air at 15 °C, emissivity of outer surface
of insulated system as specified.
26 • © BSI 2009
Table 12 Minimum insulation thickness for condensation control on ductwork carrying chilled air in ambient conditions: indoor still air
temperature +25 °C, relative humidity 80%, dewpoint temperature 21.3 °C
Minimum air Minimum thickness of insulating material (mm)

temperature ( = 0.020 ( = 0.025 ( = 0.030 ( = 0.035 ( = 0.040 ( = 0.045 ( = 0. 050
inside duct
(°C) != != != != != != != != != != != != != != != != != != != != !=
0.05 0.44 0.90 0.05 0.44 0.90 0.05 0.44 0.90 0.05 0.44 0.90 0.05 0.44 0.90 0.05 0.44 0.90 0.05 0.44 0.90
15 15 8 5 18 9 6 22 11 7 25 13 8 29 15 10 32 17 11 36 18 12
BRITISH STANDARD
10 26 10 9 32 17 11 39 20 13 45 23 15 52 26 17 58 29 19 64 33 21
5 37 19 12 47 24 15 56 28 18 64 33 21 75 38 24 83 42 27 92 47 30
0 48 25 16 60 31 20 72 37 24 84 43 27 96 49 31 108 56 35 120 61 39
Key
( = thermal conductivity of insulating material at a mean temperature of 10 °C [W/(m · K)]
! = external surface emissivity
NOTE 1 Thicknesses given are calculated in accordance with BS EN ISO 12241:1998 based on 0.6 m vertical flat surface of rectangular duct but are also adequate
for horizontal surfaces.
NOTE 2 Thicknesses given are calculated specifically against the criteria noted in the table. These thicknesses may not satisfy other design requirements.
NOTE 3 Refer to Annex B, Table B.1 for surface emissivities of common finishing materials. In situations where the ambient air temperature is greater than 25 °C
and/or the relative humidity exceeds 80%, these thicknesses will not be sufficient to control condensation.
© BSI 2009 •
BS 5422:2009
27
Table 13 Indicative thickness of insulation for ductwork carrying warm air to control heat loss
Thermal conductivity at insulation mean temperature [W/(m · K)] Maximum Permissible Heat
loss (W/m2)
0.020 0.025 0.030 0.035 0.040 0.045 0.050
Thickness of insulation (mm) with low emissivity facing: 0.05
17 21 25 29 33 38 42 16.34
Thickness of insulation (mm) with medium emissivity facing: 0.44
21 26 31 36 41 46 51 16.34
Thickness of insulation (mm) with high emissivity facing: 0.90
22 27 33 38 44 49 54 16.34
NOTE 1 Heat loss relates to the specified thickness and temperature.
NOTE 2 Insulation thicknesses in this table have been calculated according to BS EN ISO 12241:1998 using
standardized assumptions: horizontal duct at 35 °C, with 600 mm vertical sidewall in still air at 15 °C, emissivity
of outer surface of insulated system as specified.
Table 14 Indicative thickness of insulation for chilled and dual-purpose ducting to control heat transfer
Thermal conductivity at insulation mean temperature [W/(m · K)] Maximum Permissible Heat
gain (W/m2)
0.020 0.025 0.030 0.035 0.040 0.045 0.050
Thickness of insulation (mm) with low emissivity facing: 0.05
29 36 43 50 57 64 71 6.45
Thickness of insulation (mm) with medium emissivity facing: 0.44
33 41 49 58 66 74 82 6.45
Thickness of insulation (mm) with high emissivity facing: 0.90
35 43 52 61 69 78 86 6.45
standardized assumptions: horizontal duct at 13 °C, with 600 mm vertical sidewall in still air at 25 °C, emissivity
of outer surface of insulated system as specified.
NOTE 3 Thicknesses derived solely against the criteria noted in this table may not necessarily satisfy other
design requirements such as control of condensation.
28 • © BSI 2009
Table 15 Indicative thickness of insulation for non-domestic heating services to control heat loss – Low emissivity outer surfaces
Outside Low emissivity surface finish (! = 0.05)

diameter of
Low temperature heating services (≤ 95 °C) Medium temperature heating services (96 °C – 120 °C) High temperature heating services (121 °C – 150 °C)
steel pipe
on which t = 75 t = 100 t = 125
insulation
(= (= (= (= (= (= (= Max (= (= (= (= (= (= (= Max (= (= (= (= (= (= (= Max
thickness has
0.025 0.03 0.035 0.04 0.045 0.05 0.055 heat 0.025 0.03 0.035 0.04 0.045 0.05 0.055 heat 0.025 0.03 0.035 0.04 0.045 0.05 0.055 heat
been based
loss loss loss
BRITISH STANDARD
17.2 12 17 22 30 39 51 66 8.9 11 15 20 26 34 44 56 13.34 10 13 18 24 31 39 50 17.92

21.3 14 20 26 35 46 59 75 9.28 14 18 25 32 42 54 69 13.56 12 17 22 29 38 48 61 18.32
26.9 16 22 29 38 49 62 78 10.06 17 24 31 41 53 67 85 13.83 16 22 28 37 47 60 76 18.7
33.7 18 24 31 40 51 64 79 11.07 21 28 37 48 62 78 98 14.39 20 27 36 46 59 74 93 19.02
42.4 20 26 33 42 52 65 79 12.3 24 32 41 52 66 83 103 15.66 26 35 45 59 74 93 117 19.25
48.3 21 27 35 44 55 67 82 12.94 25 33 42 53 67 83 102 16.67 28 37 48 61 77 97 120 20.17
60.3 23 29 37 46 56 68 82 14.45 27 36 46 57 71 87 106 18.25 31 41 52 66 83 102 125 21.96
76.1 24 31 39 48 58 70 83 16.35 30 39 49 60 74 89 107 20.42 34 45 57 71 88 107 129 24.21
88.9 25 32 40 49 59 70 82 17.91 31 40 51 62 76 91 108 22.09 36 47 60 74 91 110 132 25.99
114.3 27 34 42 51 61 71 83 20.77 34 43 54 65 79 93 110 25.31 40 51 64 79 96 115 136 29.32
139.7 28 35 43 52 61 71 82 23.71 36 46 57 68 82 96 112 28.23 43 55 68 83 100 118 139 32.47
168.3 29 37 44 53 62 72 82 26.89 38 48 59 70 83 98 113 31.61 46 58 71 86 103 121 141 36.04
219.1 30 38 45 54 62 72 82 32.54 40 50 61 72 85 98 113 37.66 49 62 75 90 106 124 144 42.16
273 31 38 46 54 62 71 80 38.83 42 52 63 74 87 100 114 43.72 52 64 78 93 109 127 145 48.48
Key
t = water temperature; standardized assumption for calculation purposes (°C)
NOTE 1 Insulation thicknesses in this table have been calculated according to BS EN ISO 12241:1998 using standardized assumptions: horizontal pipe at t °C in still air at 15 °C, emissivity of outer
NOTE 3 The thicknesses in this table are applicable to pipes serving commercial solar hot water panels.
© BSI 2009 •
BS 5422:2009
29
Table 16 Indicative thickness of insulation for non-domestic heating services to control heat loss – High emissivity outer surfaces
Outside High emissivity surface finish (! = 0.9)

diameter of
Low temperature heating services (≤ 95 °C) Medium temperature heating services (96 °C – 120 °C) High temperature heating services (121 °C – 150 °C)
steel pipe
on which t = 75 t = 100 t = 125
insulation
(= (= (= (= (= (= (= Max (= (= (= (= (= (= (= Max (= (= (= (= (= (= (= Max
BS 5422:2009
thickness has
30 • © BSI 2009
0.025 0.03 0.035 0.04 0.045 0.05 0.055 heat 0.025 0.03 0.035 0.04 0.045 0.05 0.055 heat 0.025 0.03 0.035 0.04 0.045 0.05 0.055 heat
been based
loss loss loss
17.2 14 19 25 34 44 57 72 8.9 13 17 23 30 38 49 62 13.34 12 16 21 28 35 45 57 17.92
21.3 16 22 30 39 50 64 81 9.28 16 21 28 36 47 60 75 13.56 15 20 26 33 42 54 67 18.32
26.9 18 25 33 42 54 68 85 10.06 20 26 35 45 58 73 92 13.83 18 24 32 41 52 66 82 18.7
33.7 20 27 35 44 56 69 85 11.07 23 31 41 53 67 84 106 14.39 23 30 39 51 64 81 100 19.02
42.4 22 29 37 46 57 70 86 12.3 26 35 45 57 72 89 110 15.66 28 38 49 63 80 100 124 19.25
48.3 23 30 39 48 60 73 88 12.94 27 36 46 58 72 89 109 16.67 30 40 52 66 83 103 127 20.17
60.3 25 32 41 51 62 74 89 14.45 30 39 50 62 77 94 113 18.25 34 44 57 71 88 109 133 21.96
76.1 27 35 43 53 64 76 90 16.35 32 42 53 65 80 96 115 20.42 37 48 61 76 94 114 137 24.21
88.9 28 36 44 54 64 76 90 17.91 34 44 55 68 82 98 116 22.09 39 51 64 79 97 117 140 25.99
114.3 30 38 47 56 66 78 91 20.77 37 47 58 71 85 100 118 25.31 43 55 69 85 102 122 144 29.32
139.7 31 39 48 57 67 78 90 23.71 39 50 61 74 88 103 120 28.23 46 59 73 89 106 126 148 32.47
168.3 33 40 49 58 68 79 90 26.89 41 52 64 76 90 105 122 31.61 49 62 76 92 109 129 150 36.04
219.1 34 42 50 60 69 79 90 32.54 44 55 66 79 92 106 122 37.66 53 66 81 96 114 132 153 42.16
273 35 43 51 60 69 79 89 38.83 46 57 68 81 94 108 123 43.72 56 69 84 100 117 135 155 48.48
Key
t = water temperature; standardized assumption for calculation purposes (°C)
NOTE 1 Insulation thicknesses in this table have been calculated according to BS EN ISO 12241:1998 using standardized assumptions: horizontal pipe at t °C in still air at 15 °C, emissivity of outer
NOTE 3 The thicknesses in this table are applicable to pipes serving commercial solar hot water panels.
BRITISH STANDARD
Table 17 Indicative thickness of insulation for non-domestic hot water service areas to control heat loss –
Low emissivity outer surfaces
Outside diameter Thermal conductivity at insulation mean temperature Maximum

of pipe on which [W/(m · K)] Permissible
insulation thickness Heat loss
(low emissivity outer surface: ! = 0.05)
has been based
(mm) 0.025 0.030 0.035 0.040 0.045 0.050 0.055
Thickness of insulation (mm) (W/m)
17.2 12 17 23 31 41 53 69 6.60
21.3 14 19 25 33 43 55 70 7.13
26.9 15 21 27 35 45 57 71 7.83
33.7 17 22 29 37 47 58 72 8.62
42.4 18 23 30 38 47 57 70 9.72
48.3 19 25 32 40 49 60 73 10.21
60.3 20 26 33 41 50 60 71 11.57
76.1 22 28 35 43 52 61 72 13.09
88.9 22 28 35 43 51 60 70 14.58
114.3 23 29 36 43 51 60 69 17.20
139.7 24 31 37 44 52 60 69 19.65
168.3 25 32 38 45 53 61 70 22.31
219.1 26 32 38 45 52 60 68 27.52
273.0 and above 27 33 39 46 53 60 68 32.40
standardized assumptions: horizontal pipe at 60 °C in still air at 15 °C, emissivity of outer surface of insulated
system as specified.
© BSI 2009 • 31
Table 18 Indicative thickness of insulation for non-domestic hot water service areas to control heat loss –
High emissivity outer surfaces
Outside diameter Thermal conductivity at insulation mean temperature Maximum

of pipe on which [W/(m · K)] Permissible
insulation thickness Heat loss
(high emissivity outer surface: ! = 0.90)
has been based
(mm) 0.025 0.030 0.035 0.040 0.045 0.050 0.055
17.2 14 19 26 34 45 58 75 6.60
21.3 16 21 28 37 47 60 76 7.13
26.9 17 23 30 39 49 62 77 7.83
33.7 19 25 32 41 51 63 78 8.62
42.4 20 26 33 42 52 63 76 9.72
48.3 21 28 35 44 54 66 79 10.21
60.3 23 29 37 45 55 66 78 11.57
76.1 25 31 39 47 57 67 79 13.09
88.9 25 32 39 47 56 66 77 14.58
114.3 26 33 40 48 57 66 77 17.20
139.7 27 34 41 49 58 67 77 19.65
168.3 29 35 43 51 59 68 77 22.31
219.1 29 36 43 51 59 67 76 27.52
273.0 and above 30 37 44 52 60 68 77 32.40
9 Central heating and hot water services for

domestic applications
Approved Documents L1A [10] and L1B [11], Technical Booklet F1 [12] and
Domestic Technical Handbook [2], Section 6.
The thicknesses of insulation specified in Table 19 and Table 20 to limit
heat transfer meet or improve upon the minimum requirements of
Approved Documents L1A [10] and L1B [11] and Technical Booklet F1 [12].
However, these thicknesses of insulation might not comply with future
revisions of the Building Regulations [5] and the Building Regulations
(Northern Ireland) [6], and the current versions of these documents should
be consulted to ensure compliance.
Section 6 of the Domestic Technical Handbook [2] retains references to
guidance given in BS 5422:2001 as a means of showing compliance.
NOTE 2 For replacement systems, whenever a boiler or hot water storage
vessel is replaced in an existing system, any pipes that are exposed as
part of the work or are otherwise accessible should be insulated with
insulation labelled as complying with the Domestic Heating Compliance
Guide [13] or to some lesser standard where practical constraints dictate.
32 • © BSI 2009
of greater thicknesses of insulation can provide substantial financial and

environmental benefits. Additional considerations might include acoustic
performance, aesthetic qualities, fire properties, durability and thermal
performance for reasons other than energy reduction; such as process
control, control of internal building environment, surface temperature
and freezing. This standard provides guidance on fire properties and
thermal performance only.

9.2.1 General
The physical characteristics of the insulating material, together with
adhesive, fixing, vapour barrier and finishing materials, shall conform
to 5.1, 9.2.2 and 9.2.3.

Insulation materials and systems used for central heating and hot and
cold water supply installations for domestic applications shall conform
to the following requirements.
may spread.
faced or unfaced) shall be Class 1 (national class) or better.
© BSI 2009 • 33

NOTE See Annex E for an explanation of “limited combustibility”,
Where insulation is used on the exterior of pipework that is exposed
within the building, the complete assembly of materials as installed
shall have a rating for the surface spread of flame of not less than that
for the wall or ceiling it traverses.
9.2.3 Vapour barriers – Permeance requirements

Insulation materials and systems used for cold water services shall
be installed in accordance with and shall conform to the permeance
the permeance of the material used for the vapour barrier shall not
exceed the values given in Table 1 depending on the temperature of
the plant.
9.2.4 Maximum and minimum service temperature

The insulation selected shall be suitable for use at the maximum and
minimum temperatures of the intended application.
NOTE For example, pipes serving solar heated hot water systems may be
subject to peak temperatures of greater than 150 °C.
9.3 Thickness for central heating and hot water pipes to

limit heat losses
NOTE 1 Attention is drawn to the thicknesses of insulation for hot water
pipes referred to by the Domestic Heating Compliance Guide [13] in order
to restrict uncontrolled heat losses.
NOTE 2 Particular attention should be paid to situations where cold
water pipes run adjacent to heating or hot water pipes in order to prevent
uncontrolled pipe warming.
NOTE 3 Where pipes are in unheated areas or pass outside the envelope
of the building, attention is drawn to the need to protect pipes against
freezing.
Thicknesses of insulation to limit heat losses shall be not less than
those specified in Table 19 and Table 20.
Thicknesses of insulation for pipe diameters not shown in Table 19 and
with Annex H.
For pipes of diameter greater than 54 mm, the pipes in Table 19 and
Table 20 shall be assumed to be 54 mm for calculation purposes.
horizontal pipe at 60 °C in still air at 15 °C, emissivity of outer surface
of insulated system as specified.
34 • © BSI 2009
Table 19 Indicative thickness of insulation for domestic heating and hot water systems having low
emissivity outer surfaces
Outside diameter of Thermal conductivity at 40 °C Maximum Permissible

pipe on which insulation [W/(m · K)] Heat loss
thickness has been based (low emissivity facing: 0.05)
(mm)
0.025 0.030 0.035 0.040 0.045
8.0 3 5 6 8 11 7.06
10.0 5 6 8 11 14 7.23
12.0 6 8 10 14 18 7.35
15.0 7 9 12 15 20 7.89
22.0 8 11 14 18 23 9.12
28.0 10 12 16 20 24 10.07
35.0 11 14 17 22 26 11.08
42.0 12 15 18 23 27 12.19
54.0 12 16 19 23 28 14.12
NOTE 3 This table is applicable to pipes serving solar hot water panels.
Table 20 Indicative thickness of insulation for domestic heating and hot water systems having high
emissivity outer surfaces
Outside diameter of Thermal conductivity at 40 °C Maximum Permissible

pipe on which insulation [W/(m · K)] Heat loss
thickness has been based (high emissivity facing: 0.95)
(mm)
0.025 0.030 0.035 0.040 0.045
8.0 5 7 9 12 16 7.06
10.0 6 8 11 15 20 7.23
12.0 7 10 14 18 23 7.35
15.0 9 12 15 20 26 7.89
22.0 11 14 18 23 29 9.12
28.0 12 16 20 25 31 10.07
35.0 13 17 22 27 33 11.08
42.0 14 18 23 28 34 12.19
54.0 15 19 24 29 35 14.12
NOTE 3 This table is applicable to pipes serving solar hot water panels.
© BSI 2009 • 35
10 Process pipework and equipment

applications
10.1.1 General
performance requirements of the application, and the materials to
be used, in accordance with Clause 4, as well as the requirements
specified in 10.1.2 and 10.1.3.
NOTE For the applications appropriate to this Clause, the specifier
typically indicates the precise performance requirements of the insulation
system.
10.1.2 Special service requirements

Reference shall be included in the specification to any difficult or
unusual site conditions that influence the selection and/or application
of insulating materials, e.g. relevant to transport, access, storage,
scaffolding and weather protection.
10.1.3 Basis on which thickness is to be determined

The specifier shall state the basis for selection to be used and provide
the relevant information giving due consideration to safety and
environmental requirements.
NOTE See 10.3.
10.2.1 General
The physical characteristics of the insulating material, fixing and
finishing materials, whether applied during manufacture or on site,
shall conform to 5.1, 10.2.2 and 10.2.3.

Insulation materials and systems used for process applications shall
conform to the following requirements.
may spread.
36 • © BSI 2009
Insulation materials for use at temperatures above 230 °C (excluding

finishing materials) shall be of “limited combustibility” or
“non-combustible”.

of “limited combustibility” or “non-combustible”. In addition, the
NOTE See Annex E for an explanation of “limited combustibility”,

NOTE 1 Process applications can encompass systems running at
temperatures throughout the full range of this standard, –40 °C
to +700 °C, and beyond.
Where a process application has a normal operating temperature
below ambient temperature, the insulation material and systems used
for such an application shall be installed in accordance with and shall
conform to the permeance requirements for water vapour barriers
specified in 5.6.
Where a process application has a normal operating temperature
above ambient temperature, and a water vapour barrier is installed,
the system shall be installed in accordance with and shall conform to
the permeance requirements specified in 5.6.
NOTE 2 The need to apply a vapour barrier is dependant upon whether
such a system can on occasion have a surface temperature below the dew
point temperature.
© BSI 2009 • 37
10.3.1 Control of heat loss

NOTE The thicknesses of insulation to control heat loss under process
conditions have been derived according to the methodology given in
Annex A. Recognizing the need to reduce carbon dioxide emissions,
particularly in the process sector, the thicknesses given in Table 21 are
intended to support this objective.
thickness shall be as given in Table 21.
BS EN ISO 12241:1998 using standardized assumptions: horizontal pipe
in still air at 20 °C. Surface emissivity corresponding to outer
surface specified.
Thicknesses of insulation for pipe diameters not shown in Table 21, and
for all plastic pipes, shall be determined in accordance with Annex H.
The heat losses applicable for pipes of diameter greater than 273 mm
and flat surfaces shall be calculated as if the pipe or plant was a 273 mm
diameter surface as shown in Table 21.
10.3.2 Economic parameters

NOTE 1 Guidance for the determination of insulation thickness in
accordance with economic parameters other than those used to calculate
the control of heat loss in Table 21 is given in Annex G.
NOTE 2 Control of heat loss thicknesses (10.3.1) are preferred where
practicable because of their potentially greater contribution to
environmental objectives in this sensitive sector.
10.3.3 Other design criteria

Where there is a requirement to control surface temperature to the
extent described in Table 22, Table 23 and Table 24, the insulation
thicknesses given in these tables shall be used, as appropriate.
NOTE These tables provide information, which may be relevant to a risk
assessment undertaken in relation to the protection of personnel from
contact injury or to process performance requirements. BS EN ISO 13732-1,
ISO/TS 13732-2 and BS EN ISO 13732-3 give guidance on surface
temperatures for protection of personnel from contact injury.
Thicknesses of insulation for pipe diameters not shown in Table 22,
Table 23 and Table 24, and for all plastic pipes, shall be determined in
accordance with Annex H.
Where other design criteria are identified, e.g. a specified heat loss (see
Table 25, Table 26 and Table 27), a specified temperature on the outer
surface, or a special condition at the point of delivery, the calculation
shall be in accordance with BS EN ISO 12241:1998 (see also BS 5970).
38 • © BSI 2009
Table 21 Minimum insulation thickness for process pipework and equipment to control heat loss
Outside t = 100 t = 200 t = 300

diameter of
steel pipe Insulation thickness (mm) Max. Insulation thickness (mm) Max. Insulation thickness (mm) Max.
on which heat loss heat loss heat loss
(= (= (= (= (= (= (= (W/m) (= (= (= (= (= (= (= (W/m) (= (= (= (= (= (= (= (W/m)
insulation 0.025 0.030 0.035 0.040 0.045 0.050 0.055 0.035 0.040 0.045 0.050 0.055 0.060 0.065 0.045 0.050 0.055 0.060 0.065 0.070 0.075
thickness has
been based
(mm)
17.2 10 14 19 24 31 40 51 12.79 20 26 33 42 54 68 85 28.67 30 38 47 59 73 91 112 47.12
BRITISH STANDARD
21.3 11 15 20 25 32 40 51 14.04 22 28 36 46 57 71 88 30.72 32 41 50 62 76 93 114 50.54

26.9 13 17 21 27 34 42 52 15.42 24 30 38 47 59 72 88 33.73 35 43 53 65 79 95 115 54.97
33.7 14 18 23 28 35 43 52 17.25 26 32 40 49 60 73 88 37.11 38 46 56 68 81 97 116 59.90
42.4 15 19 24 30 37 45 54 19.15 28 35 43 52 63 76 90 40.76 41 49 59 71 84 99 116 65.79
48.3 16 20 25 31 38 46 54 20.42 29 36 44 53 64 76 90 43.42 43 51 61 73 86 101 118 69.42
60.3 17 21 26 32 39 46 54 23.17 31 38 46 55 65 77 90 48.44 46 54 64 76 88 102 119 76.66
76.1 18 23 28 34 41 48 56 26.21 34 41 49 58 68 80 92 54.20 49 58 68 80 92 106 122 85.08
88.9 19 24 29 35 42 49 57 28.73 36 43 51 60 70 81 94 58.66 51 60 70 81 94 107 122 92.02
114.3 20 25 30 36 43 49 57 33.89 38 46 54 63 73 84 96 67.25 55 64 74 85 97 110 125 104.55
139.7 21 26 31 37 44 50 57 38.74 40 48 56 65 75 85 97 75.74 58 67 77 88 100 113 127 116.62
168.3 22 27 33 38 44 51 58 43.99 42 50 58 67 77 87 98 84.85 61 70 80 91 103 115 129 129.46
219.1 23 28 34 39 45 52 58 53.38 44 52 60 69 78 88 99 101.24 64 73 83 94 105 117 130 152.70
273 24 29 35 40 46 53 59 62.87 46 54 62 71 80 90 100 117.64 67 76 86 97 108 120 132 175.73
Key
t = hot face temperature (°C)
( = thermal conductivity at mean temperature of insulation [W/( m · K)]
NOTE 1 Insulation thicknesses in this table have been calculated according to BS EN ISO 12241:1998 using standardized assumptions: horizontal pipe in still air at 20 °C. Surface emissivity
corresponding to outer surface specified.
NOTE 2 Maximum heat loss values for intermediate operating temperatures may be deduced by interpolation.
NOTE 3 Heat loss measured in Watts per metre (W/m) relates to the specified thickness and temperature.
NOTE 4 The thermal conductivity of insulation materials increases with mean temperature and for any given material. The use of a different thermal conductivity can be required for each operating
temperature.
NOTE 5 These thicknesses may not satisfy other design requirements, in particular those for control of surface temperature (see Table 22, Table 23 and Table 24).
© BSI 2009 •
BS 5422:2009
39
Table 21 Minimum insulation thickness for process pipework and equipment to control heat loss (continued)
Outside t = 400 t = 500 t = 600

diameter of
steel pipe Insulation thickness (mm) Max. Insulation thickness (mm) Max. Insulation thickness (mm) Max.
on which heat loss heat loss heat loss
(= (= (= (= (= (= (= (W/m) (= (= (= (= (= (= (= (W/m) (= (= (= (= (= (= (= (W/m)
insulation 0.055 0.060 0.065 0.070 0.075 0.080 0.085 0.065 0.070 0.075 0.080 0.085 0.090 0.095 0.075 0.080 0.085 0.090 0.095 0.100 0.105
BS 5422:2009
thickness has
40 • © BSI 2009
been based
(mm)
17.2 39 48 59 73 89 108 131 69.08 46 56 67 80 96 115 137 96.08 52 62 73 87 102 120 141 126.93
21.3 42 51 62 76 91 110 132 74.10 49 59 70 83 98 116 137 103.00 56 66 77 91 106 123 143 135.40
26.9 46 55 66 80 95 113 134 80.06 54 64 75 88 103 121 141 110.72 61 71 82 96 111 128 147 145.58
33.7 49 58 69 82 97 114 134 87.16 58 68 79 92 107 124 143 119.80 66 76 87 101 115 132 151 156.77
42.4 53 62 73 86 101 117 136 95.05 62 72 83 96 110 127 145 130.57 71 81 92 105 120 136 155 170.00
48.3 55 65 76 89 104 120 139 99.66 64 75 86 99 113 129 148 136.95 73 84 95 108 123 139 157 178.30
60.3 59 68 79 92 106 121 139 109.91 69 80 91 104 118 134 151 149.28 78 89 101 113 127 143 160 194.30
76.1 63 73 84 97 111 126 143 121.21 74 85 96 109 123 138 155 164.62 84 95 107 119 133 149 165 213.22
88.9 66 76 87 100 113 128 145 130.15 77 88 99 112 125 140 157 176.67 88 99 111 123 137 152 168 227.69
114.3 71 81 92 105 118 133 148 146.83 83 94 105 118 131 146 161 198.17 95 106 118 130 144 159 174 254.18
139.7 74 84 95 107 120 134 149 163.60 88 99 110 123 136 150 166 218.23 100 111 123 135 149 163 178 279.81
168.3 78 88 99 111 124 138 153 180.38 92 103 114 126 140 154 169 240.54 106 117 129 141 155 169 184 305.53
219.1 83 93 104 116 129 142 156 209.59 98 109 120 132 145 159 173 277.77 113 124 136 148 161 175 189 350.96
273 87 97 108 120 133 146 159 239.40 103 114 125 137 150 163 176 315.35 123 135 147 159 173 191 191 386.92
Key
temperature.
BRITISH STANDARD
Table 21 Minimum insulation thickness for process pipework and equipment to control heat loss (continued)
Outside t = 700
diameter of
steel pipe Insulation thickness (mm) Max.
on which heat loss
(W/m)
insulation (= (= (= (= (= (= (=
thickness has 0.085 0.090 0.095 0.100 0.105 0.110 0.115
been based
(mm)
17.2 56 65 76 88 103 119 138 163.63
BRITISH STANDARD
21.3 60 69 80 92 106 122 141 174.49

26.9 65 75 86 98 113 128 146 186.89
33.7 70 80 91 103 117 133 150 201.20
42.4 76 86 97 109 123 138 155 217.29
48.3 79 89 100 112 126 141 158 227.84
60.3 85 95 106 118 132 147 163 247.23
76.1 91 102 113 125 139 153 169 270.20
88.9 95 106 117 129 143 157 173 288.43
114.3 103 114 125 137 151 165 180 320.67
139.7 109 120 131 143 157 170 185 351.43
168.3 115 126 137 149 162 176 191 383.75
219.1 123 135 146 158 170 184 192 437.18
273 128 139 154 166 179 193 193 495.09
Key
temperature.
© BSI 2009 •
BS 5422:2009
41
Table 22 Minimum insulation thickness to control the surface temperature of a non-metallic surface with a surface emissivity of 0.90 and design cold
face temperature of 59 °C
Outside diameter t = 100 t = 200 t = 300

of steel pipe Insulation thickness (mm) Insulation thickness (mm) Insulation thickness (mm)
(mm)
BS 5422:2009
( = 0.025 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.065 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.065
42 • © BSI 2009
17.2 2 3 3 4 7 9 11 12 12 14 17 19
21.3 2 3 4 4 8 10 11 13 12 15 18 20
26.9 2 3 4 4 8 10 12 14 13 16 19 22
33.7 2 3 4 4 9 11 13 15 14 17 20 23
42.4 2 3 4 5 9 11 13 15 14 18 21 24
48.3 2 3 4 5 9 12 14 16 15 18 22 25
60.3 3 3 4 5 10 12 14 17 15 19 23 26
76.1 3 3 4 5 10 13 15 17 16 20 24 28
88.9 3 3 4 5 10 13 15 18 17 21 25 29
101.6 3 4 4 5 11 13 16 18 17 21 25 29
114.3 3 4 4 5 11 13 16 19 17 22 26 30
139.7 3 4 5 5 11 14 17 19 18 23 27 31
168.3 3 4 5 6 11 14 17 20 19 23 28 32
219.1 3 4 5 6 12 15 18 21 19 24 29 34
244.5 3 4 5 6 12 15 18 21 20 25 30 35
273.0 3 4 5 6 12 15 18 21 20 25 30 35
323.9 3 4 5 6 12 16 19 22 20 26 31 36
355.6 3 4 5 6 12 16 19 22 21 26 31 37
406.4 3 4 5 6 13 16 19 23 21 27 32 37
457.0 3 4 5 6 13 16 20 23 21 27 33 38
508.0 3 4 5 6 13 16 20 23 22 27 33 39
610.0 3 4 5 6 13 16 20 23 22 27 33 39
Flat surfaces 3 4 5 6 13 17 20 24 22 28 34 41
Key
t = hot face temperature at mean temperature (°C) (with ambient still air at 20 °C)
NOTE 2 To simplify the use of this table, the values shaded have been adjusted to avoid the specification of apparently anomalous results given by the
calculation method in BS EN ISO 12241:1998, due to the transition from turbulent to laminar flow.
BRITISH STANDARD
face temperature of 59 °C (continued)
Outside diameter t = 400 t = 500 t = 600 t = 700

of steel pipe Insulation thickness (mm) Insulation thickness (mm) Insulation thickness (mm) Insulation thickness (mm)
(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.045 0.055 0.065 0.075 0.085 0.055 0.065 0.075 0.085 0.095 0.065 0.075 0.085 0.095 0.105 0.065 0.075 0.085 0.095 0.105
17.2 19 22 26 29 32 27 32 35 39 43 37 42 46 51 55 43 48 53 59 64
BRITISH STANDARD
21.3 20 24 27 30 34 29 33 37 42 46 39 44 49 54 58 45 51 56 62 67
26.9 21 25 29 32 36 31 35 40 44 48 42 47 52 57 62 48 54 60 66 71
33.7 22 26 30 34 38 33 38 42 47 51 44 50 55 61 66 51 57 64 70 76
42.4 24 28 32 36 40 35 40 45 50 55 47 53 59 64 70 54 61 68 74 80
48.3 24 29 33 37 42 36 41 46 51 56 49 55 61 67 72 56 63 70 77 83
60.3 26 31 35 40 44 38 44 49 54 60 52 58 64 71 77 59 67 74 81 88
76.1 27 32 37 42 47 40 46 52 58 63 55 62 68 75 81 63 71 79 86 94
88.9 28 33 38 43 48 42 48 54 60 66 57 64 71 78 85 66 74 82 90 97
101.6 29 34 40 45 50 43 49 56 62 68 59 66 74 81 88 68 76 85 93 101
114.3 30 35 41 46 51 44 51 57 64 70 60 68 76 83 90 70 79 87 96 104
139.7 31 37 42 48 54 46 53 60 67 73 63 71 79 87 95 73 82 92 100 109
168.3 32 38 44 50 56 48 55 63 70 77 66 74 83 91 99 76 86 96 105 114
219.1 33 40 46 53 59 50 58 66 74 81 70 79 88 97 105 81 91 102 112 122
244.5 34 41 47 54 60 51 60 68 75 83 71 81 90 99 108 83 94 104 115 125
273.0 35 42 48 55 61 52 61 69 77 85 73 83 92 101 111 85 96 107 117 128
323.9 36 43 50 57 63 54 63 71 80 88 75 85 95 105 115 87 99 111 122 133
355.6 36 43 51 58 64 55 64 73 81 90 77 87 97 107 117 89 101 113 124 135
406.4 37 44 52 59 66 56 65 74 83 92 79 89 100 110 117 91 104 113 124 135
457.0 37 45 53 60 67 57 67 76 85 92 80 89 100 110 117 91 104 113 124 135
508.0 38 46 53 61 67 58 67 76 85 92 80 89 100 110 117 91 104 113 125 136
610.0 38 46 53 61 67 58 67 76 85 92 80 89 100 110 120 91 104 116 128 139
Flat surfaces 40 49 57 66 75 63 74 85 97 108 91 104 118 132 146 107 124 140 156 173
Key
© BSI 2009 •
BS 5422:2009
43
Table 23 Minimum insulation thickness to control the surface temperature of a metallic surface with a surface emissivity of 0.05 and design cold face
temperature of 50 °C

(mm)
BS 5422:2009
( = 0.025 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.065 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.065
44 • © BSI 2009
17.2 5 7 8 10 17 21 25 29 27 33 40 46
21.3 5 7 9 10 18 23 27 31 28 35 42 49
26.9 6 7 9 11 19 24 29 34 31 38 46 53
33.7 6 8 10 12 21 26 31 36 33 41 49 57
42.4 6 8 11 13 22 28 33 39 35 44 52 61
48.3 6 9 11 13 23 29 35 40 37 46 55 63
60.3 7 9 12 14 25 31 37 43 39 49 58 68
76.1 7 10 12 15 27 33 40 46 42 53 63 73
88.9 8 10 13 15 28 35 42 49 44 55 66 77
101.6 8 11 13 16 29 36 44 51 46 57 69 80
114.3 8 11 14 17 30 38 45 52 48 60 71 83
139.7 8 11 14 17 32 40 48 56 50 63 76 88
168.3 9 12 15 18 33 42 50 59 53 67 80 93
219.1 9 13 16 20 36 45 54 63 57 72 87 101
244.5 10 13 17 20 37 47 56 65 59 75 90 104
273.0 10 14 17 21 38 48 58 68 61 77 93 108
323.9 10 14 18 22 40 50 61 71 64 81 97 113
355.6 10 14 18 22 41 52 62 73 66 83 100 116
406.4 11 15 19 23 42 53 65 75 68 86 104 121
457.0 11 15 19 23 43 55 67 78 70 89 107 121
508.0 11 16 20 24 45 57 69 80 72 92 107 121
610.0 12 16 21 25 45 57 69 80 72 92 107 121
Flat surfaces 12 16 21 25 46 59 72 85 76 98 120 141
Key
BRITISH STANDARD
Table 23 Minimum insulation thickness to control the surface temperature of a metallic surface with a surface emissivity of 0.05 and design cold face
temperature of 50 °C (continued)

(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.045 0.055 0.065 0.075 0.085 0.055 0.065 0.075 0.085 0.095 0.065 0.075 0.085 0.095 0.105 0.065 0.075 0.085 0.095 0.105
17.2 45 54 62 71 80 67 79 90 101 112 95 108 122 135 148 111 126 142 158 174
BRITISH STANDARD
21.3 48 57 67 76 85 72 84 95 107 119 101 115 129 143 157 117 134 151 167 184
26.9 51 61 71 81 91 77 90 102 114 127 108 123 138 153 168 125 143 161 178 196
33.7 55 66 76 87 97 82 96 109 122 135 115 131 147 163 179 134 153 171 190 209
42.4 59 71 82 93 104 88 103 117 131 145 123 140 157 174 191 143 163 183 203 222
48.3 62 74 85 97 109 92 107 122 136 151 128 146 163 181 198 149 170 190 211 231
60.3 66 79 91 104 116 99 114 130 146 161 137 156 174 193 211 159 181 203 225 246
76.1 71 85 98 112 125 106 123 140 156 173 147 167 187 207 226 171 194 218 241 264
88.9 74 89 103 117 131 111 129 147 164 181 154 175 196 217 237 179 204 228 252 276
101.6 78 93 108 122 137 116 135 153 171 189 161 183 204 226 247 187 212 237 262 287
114.3 80 96 112 127 142 120 140 158 177 196 167 190 212 234 256 194 220 246 272 287
139.7 86 102 119 135 151 128 149 169 189 208 178 202 225 249 272 206 234 262 272 287
168.3 91 108 126 143 160 136 157 179 200 221 188 214 239 249 272 218 248 262 272 290
219.1 98 118 136 155 173 147 171 194 217 221 204 232 239 250 272 237 248 262 284 307
244.5 101 121 141 160 179 152 177 201 224 221 211 232 239 256 277 237 248 267 291 315
273.0 105 126 146 166 186 157 183 208 224 224 211 232 240 262 283 237 248 274 298 323
323.9 110 132 154 175 186 166 183 208 224 231 211 232 249 271 294 237 257 284 310 335
355.6 113 136 158 175 186 166 183 208 224 236 211 232 253 277 300 237 262 289 316 342
406.4 118 141 158 175 186 166 183 208 224 242 211 235 260 284 308 240 269 297 325 351
457.0 118 141 158 175 186 166 183 208 226 247 214 240 266 291 315 245 275 304 333 360
508.0 118 141 158 175 187 166 184 208 230 252 218 245 271 297 322 250 281 311 340 368
610.0 118 141 158 175 192 166 190 214 237 260 224 253 280 307 333 258 290 321 352 381
Flat surfaces 137 167 198 228 259 215 254 293 332 371 311 358 406 454 501 367 423 480 536 593
Key
© BSI 2009 •
BS 5422:2009
45
face temperature of 50 °C

(mm)
BS 5422:2009
( = 0.025 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.065 ( = 0.035 ( = 0.045 ( = 0.055 ( = 0.065
46 • © BSI 2009
17.2 3 4 5 6 10 13 15 17 15 19 22 26
21.3 3 4 5 6 11 13 16 18 16 20 24 27
26.9 3 5 6 7 11 14 16 19 17 21 25 29
33.7 4 5 6 7 12 15 17 20 18 23 27 31
42.4 4 5 6 7 13 15 18 21 19 24 28 32
48.3 4 5 6 7 13 16 19 22 20 25 29 33
60.3 4 5 6 8 13 17 20 23 21 26 31 35
76.1 4 5 7 8 14 18 21 24 22 27 32 37
88.9 4 5 7 8 14 18 22 25 23 28 34 39
101.6 4 6 7 8 15 18 22 26 23 29 35 40
114.3 4 6 7 8 15 19 23 26 24 30 35 41
139.7 4 6 7 9 16 20 23 27 25 31 37 43
168.3 4 6 7 9 16 20 24 28 26 32 38 44
219.1 5 6 8 9 17 21 25 29 27 34 40 47
244.5 5 6 8 9 17 21 26 30 27 34 41 48
273.0 5 6 8 9 17 22 26 30 28 35 42 49
323.9 5 6 8 10 18 22 27 31 28 36 43 50
355.6 5 6 8 10 18 22 27 32 29 36 44 51
406.4 5 6 8 10 18 23 28 32 29 37 44 52
457.0 5 7 8 10 18 23 28 33 30 37 45 53
508.0 5 7 8 10 19 23 28 33 30 38 46 54
610.0 5 7 8 10 19 24 29 34 31 39 46 54
Flat surfaces 5 7 8 10 19 24 29 35 31 40 49 58
Key
BRITISH STANDARD
face temperature of 50 °C (continued)

(mm) (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (= (=
0.045 0.055 0.065 0.075 0.085 0.055 0.065 0.075 0.085 0.095 0.065 0.075 0.085 0.095 0.105 0.065 0.075 0.085 0.095 0.105
17.2 25 29 34 38 42 36 42 47 52 57 49 55 61 67 73 56 63 70 77 84
BRITISH STANDARD
21.3 26 31 36 40 45 38 44 49 55 60 52 58 65 71 77 59 67 74 81 88
26.9 28 33 38 43 47 41 47 53 58 64 55 62 69 75 82 63 71 79 86 94
33.7 30 35 40 45 50 43 50 56 62 68 58 66 73 80 87 67 75 84 92 99
42.4 32 37 43 48 53 46 53 59 66 72 62 70 77 85 92 71 80 89 97 105
48.3 33 39 44 50 55 47 54 61 68 74 64 72 80 88 95 74 83 92 100 109
60.3 34 41 47 53 58 50 58 65 72 79 68 76 85 93 101 78 88 97 106 116
76.1 36 43 50 56 62 53 61 69 76 84 72 81 90 99 107 83 93 103 113 123
88.9 38 45 51 58 64 55 63 72 79 87 75 84 94 103 111 86 97 107 118 128
101.6 39 46 53 60 67 57 66 74 82 90 78 87 97 106 115 89 100 111 122 132
114.3 40 47 55 62 68 59 67 76 84 93 80 90 100 109 119 92 103 114 125 136
139.7 42 49 57 64 72 61 71 80 89 97 84 94 105 115 125 96 109 120 132 143
168.3 43 51 59 67 75 64 74 83 93 102 87 99 110 120 131 101 114 126 138 150
219.1 45 54 63 71 79 68 78 88 98 108 93 105 117 128 139 107 121 134 147 160
244.5 46 55 64 73 81 69 80 90 101 111 95 107 120 131 143 110 124 138 151 164
273.0 47 56 66 74 83 71 82 93 103 114 97 110 123 135 147 112 127 141 155 169
323.9 49 58 68 77 86 73 85 96 107 118 101 114 127 140 152 117 132 147 161 176
355.6 49 59 69 78 87 74 86 98 109 120 103 116 130 143 156 119 134 150 165 176
406.4 50 61 70 80 90 76 88 100 112 123 105 120 133 143 156 122 138 150 165 176
457.0 51 62 72 82 92 78 90 102 114 123 108 120 133 143 156 122 138 150 165 178
508.0 52 63 73 83 89 79 92 102 114 123 108 120 133 144 157 122 138 152 166 181
610.0 52 63 73 83 90 79 92 102 114 124 108 121 135 148 161 123 140 155 171 186
Flat surfaces 56 68 80 93 105 87 103 119 135 151 126 145 165 184 203 149 172 194 217 240
Key
© BSI 2009 •
BS 5422:2009
47
Table 25 Heat loss from bare surfaces calculated in accordance with BS EN ISO 12241:1998 (black steel pipes)
Outside Heat loss (W/m for pipes and W/m2 for flat surfaces)
diameter t = 50 t = 100 t = 150 t = 200 t = 250 t = 300 t = 350 t = 400 t = 450 t = 500 t = 550 t = 600 t = 650 t = 700
of pipe
(mm)
BS 5422:2009
48 • © BSI 2009
12.0 17 57 110 176 257 356 476 620 791 993 1 231 1 509 1 832 2 206
15.0 20 69 133 214 313 435 582 758 969 1 220 1 514 1 859 2 260 2 723
17.2 23 78 150 241 353 491 658 859 1 099 1 384 1 720 2 113 2 571 3 100
21.3 27 93 180 290 427 594 798 1 043 1 337 1 687 2 099 2 583 3 146 3 798
22.0 28 96 186 299 439 611 821 1 074 1 378 1 738 2 164 2 662 3 243 3 916
26.9 33 114 221 356 525 732 985 1 291 1 658 2 095 2 611 3 217 3 923 4 742
28.0 35 118 229 369 544 759 1 022 1 340 1 721 2 175 2 711 3 341 4 075 4 926
33.7 41 139 269 435 641 897 1 209 1 588 2 042 2 585 3 226 3 979 4 859 5 878
42.0 49 168 326 528 781 1 094 1 478 1 944 2 505 3 175 3 968 4 901 5 990 7 254
42.4 50 169 329 532 788 1 104 1 491 1 961 2 527 3 203 4 004 4 945 6 045 7 320
48.3 56 190 369 598 885 1 242 1 679 2 212 2 853 3 619 4 527 5 595 6 843 8 292
54.0 61 209 407 660 979 1 374 1 860 2 452 3 165 4 018 5 029 6 220 7 612 9 228
60.3 68 230 448 728 1 081 1 519 2 058 2 715 3 508 4 456 5 582 6 908 8 458 10 258
67.0 74 253 492 800 1 188 1 672 2 268 2 994 3 871 4 921 6 167 7 636 9 354 11 350
76.1 83 283 551 896 1 333 1 878 2 550 3 370 4 360 5 548 6 958 8 621 10 566 12 827
80.0 87 295 576 938 1 395 1 966 2 670 3 530 4 569 5 815 7 296 9 041 11 084 13 459
88.9 95 324 632 1 031 1 535 2 165 2 943 3 894 5 044 6 424 8 064 9 998 12 263 14 897
101.6 107 365 712 1 162 1 733 2 447 3 330 4 410 5 718 7 287 9 155 11 358 13 940 16 942
108.0 113 385 752 1 228 1 832 2 588 3 523 4 668 6 056 7 721 9 703 12 042 14 782 17 969
114.3 119 405 791 1 292 1 929 2 726 3 714 4 922 6 387 8 147 10 241 12 713 15 609 18 979
139.7 142 484 947 1 549 2 316 3 279 4 474 5 939 7 716 9 853 12 399 15 406 18 932 23 036
168.3 167 571 1 119 1 833 2 746 3 894 5 321 7 072 9 200 11 760 14 812 18 420 22 653 27 582
219.1 212 722 1 419 2 330 3 498 4 971 6 806 9 063 11 809 15 117 19 065 23 736 29 220 35 609
273.0 258 880 1 731 2 848 4 283 6 098 8 362 11 152 14 550 18 647 24 221 30 135 37 067 45 134
323.9 301 1 027 2 021 3 331 5 016 7 151 10 254 13 667 17 813 22 798 28 737 35 754 43 978 53 549
Flat surfaces 285 1 212 2 405 3 949 5 897 8 317 11 286 14 890 19 226 24 396 30 515 37 700 46 081 55 794
Key
t = operating temperature (°C)
Operating conditions: ambient still air temperature 20 °C; surface emissivity 0.9; height of flat surface 0.6 m; surface orientation horizontal.
BRITISH STANDARD
Table 26 Heat loss from bare surfaces calculated in accordance with BS EN ISO 12241:1998 (copper pipes –
commercial grade, scoured to a shine)
Outside diameter Heat loss (W/m for pipes and W/m2 for flat surfaces)
of pipe t = 50 t = 100 t = 150 t = 200
(mm)
12.0 11 36 66 100
15.0 12 43 79 119
17.2 14 47 87 132
21.3 16 56 103 156
22.0 17 57 105 160
26.9 19 66 123 186
28.0 20 69 127 192
33.7 23 79 146 222
42.0 27 93 173 263
42.4 28 94 174 265
48.3 31 104 192 292
54.0 33 113 210 319
60.3 36 123 228 347

67.0 39 134 248 377
76.1 43 148 273 416
80.0 45 153 284 432
88.9 49 166 308 469
101.6 54 184 341 520
108.0 57 193 358 545
114.3 59 202 374 570
139.7 69 236 437 666
168.3 80 272 505 770
219.1 98 334 619 946
273.0 116 396 735 1 123
323.9 133 452 840 1 284
Flat surfaces 119 647 1 244 1 938
Key
Operating conditions: ambient still air temperature 20 °C; surface emissivity 0.07; height of flat surface 0.6 m; surface
orientation horizontal
© BSI 2009 • 49
Table 27 Heat loss from bare surfaces calculated in accordance with BS EN ISO 12241:1998 (copper
pipes – oxidized)
Outside diameter Heat loss (W/m for pipes and W/m2 for flat surfaces)
of pipe t = 50 t = 100 t = 150 t = 200
(mm)
12.0 15 52 99 158
15.0 18 63 120 191
17.2 21 70 135 215
21.3 25 84 162 258
22.0 25 87 166 265
26.9 30 103 197 315
28.0 31 106 204 326
33.7 36 124 239 383
42.0 44 150 289 464
42.4 44 151 292 468
48.3 50 169 326 524
54.0 55 186 359 578
60.3 60 205 395 636

67.0 66 224 433 698
76.1 73 250 484 781
80.0 77 261 505 816
88.9 84 286 554 895
101.6 94 321 623 1 007
108.0 99 339 657 1 063
114.3 104 356 691 1 118
139.7 124 424 824 1 336
168.3 146 499 971 1 577
219.1 184 629 1 226 1 997
273.0 224 763 1 491 2 432
323.9 261 888 1 737 2 837
Flat surfaces 245 1 076 2 125 3 464
Key
Operating conditions: ambient still air temperature 20 °C; surface emissivity 0.70; height of flat surface 0.6 m;
surface orientation horizontal
11 Protection against freezing

50 • © BSI 2009


NOTE 1 The use of insulation alone does not afford complete protection
against the freezing of water in pipes and vessels under all atmospheric
conditions. If the ambient temperature remains low enough for a
sufficiently long period and the movement of water through the pipe or
vessel is very slow or if the water is static, no insulation, however thick,
will prevent internal freezing.
Nonetheless, insulation does reduce the rate of cooling and delays the
onset of freezing, such that the formation of ice may be avoided if the
time intervals during which the water is static are short enough, or if
more heat is supplied from the water passing through the system than is
lost from the surface of the insulation together with the associated losses
through the metal supports and hangers, or if supplementary heating is
used, even if only in local areas.
Where an insulation material is used with a heat trace, the heat loss
shall be calculated according to the known worst case design condition
and the insulation thickness shall be such that it limits the heat loss
to 10% less than the maximum heat output of the heat trace.
NOTE 2 The time taken for water to reach its freezing point under
given initial conditions and ambient temperatures is a function of the
ratio between the heat capacity of the system (including that of the
containing vessel and of the insulation) and the rate of heat loss from it.
Consequently pipes of small bore are more vulnerable than those of larger
bore and therefore the smaller pipes require relatively greater thicknesses
of insulation for the same degree of protection against freezing.
NOTE 3 Calculations of the insulation thickness given in this standard
have been made ignoring the heat capacity of the insulation and the
surface resistance of the outer finish in order to give a worst case
condition which allows for the common situation where the temperature
of the insulation is lower than the initial temperature of the water.
A separate calculation is required if the conditions indicated in Table 28 to
Table 31 do not apply.
Where protection against freezing is required, the insulation thickness
shall, wherever possible (see Note 3 and Note 4), be in accordance
with the values given in Table 28 to Table 31, as appropriate.
with Annex H.
NOTE 4 Some of the theoretical thicknesses in the tables are impractical
to accommodate, and in such cases other means of protection, e.g.
trace-heating, drain-down, frost-stats or water-flow, should be adopted
to supplement the protection that is afforded by any reduced thickness of
insulating material.
Where insulating materials of alternative thermal conductivity are
proposed, calculation methods in accordance with BS EN ISO 12241:1998
can be used to ensure that the thickness selected affords at least the
equivalent degree of frost protection.
For smaller pipes it may not be practical to install thermal insulation
of sufficient thickness to avoid entirely the possibility of ice formation
overnight in sub-zero temperatures.
© BSI 2009 • 51
Table 28 Minimum insulation thickness to protect steel pipes against freezing – Selected industrial
process conditions
Outside Inside Insulation thickness (mm)

diameter of diameter Specified conditions 1 Specified conditions 2
pipe (bore)
(mm) (mm) (= (= (= (= (= (= (= (=
0.020 0.030 0.040 0.050 0.020 0.030 0.040 0.050
21.3 16.0 — — — — 1 034 10 350 — —
26.9 21.6 5 028 — — — 179 715 2 740 —
33.7 27.2 716 4 812 — — 74 194 472 1 119
42.4 35.9 203 708 2 349 — 37 75 137 240
48.3 41.8 124 340 875 2 195 28 51 85 135
60.3 53.0 66 141 275 513 19 32 48 69
76.1 68.8 41 75 123 193 13 21 30 40
88.9 80.8 31 54 84 122 11 17 23 31
114.3 105.3 22 35 51 70 8 12 17 21
168.3 158.6 14 21 29 37 5 8 10 13
219.1 207.9 10 16 21 27 4 6 8 10
Key
Specified conditions 1: water temperature +5 °C; ambient temperature –10 °C; evaluation period 12 h; permitted ice
formation nil
Specified conditions 2: water temperature +5 °C; ambient temperature –10 °C; evaluation period 12 h; permitted ice
formation 10 %
( = thermal conductivity [W/(m · K)]
NOTE 1 Thicknesses given are calculated specifically against the criteria noted in the table. These thicknesses
may not satisfy other design requirements.
NOTE 2 Some of the insulation thicknesses given are too large to be applied in practice but a selection
is included to highlight the difficulty in protecting small diameter pipes against freezing. To provide the
appropriate degree of frost protection to certain sizes of pipes, it may be necessary to provide additional heat
to the system, for example by circulating the water or heat tracing.
NOTE 3 Assumed densities (/) and heat capacities (CP) are as follows:
— / water = 1 000 kg/m3, CP water = 4 200 J/kg · K;
— / steel = 7 840 kg/m3, CP steel = 455 J/kg · K.
52 • © BSI 2009
Table 29 Minimum insulation thickness required to give protection against freezing – Selected
commercial and institutional conditions

diameter diameter Specified conditions 1 Specified conditions 2
(mm) (bore)
(mm) (= (= (= (= (= (= (= (= (= (=
0.020 0.025 0.030 0.035 0.040 0.020 0.025 0.030 0.035 0.040
Copper pipes A)
15.0 13.6 23 35 53 78 113 68 126 229 413 740
22.0 20.2 10 14 18 23 28 21 30 42 58 78
28.0 26.2 7 9 11 13 16 13 17 22 28 35
35.0 32.6 5 7 8 10 11 9 12 15 18 22
42.0 39.6 4 5 6 7 9 7 9 11 13 16
54.0 51.6 3 4 5 5 6 5 7 8 9 11
76.1 73.1 2 3 3 4 4 4 5 5 6 7
108.0 105.0 2 2 2 3 3 3 3 4 4 5
B)
Steel pipes
21.3 16.0 18 26 35 48 64 44 71 112 173 265
26.9 21.6 10 13 17 21 26 20 28 39 52 68
33.7 27.2 7 9 12 14 17 13 18 23 29 36
42.4 35.9 5 6 8 9 11 9 11 14 17 20
48.3 41.8 4 5 6 7 9 7 9 11 13 16
60.3 53.0 3 4 5 6 7 5 7 8 10 11
76.1 68.8 3 3 4 4 5 4 5 6 7 8
88.9 80.8 2 3 3 4 4 3 4 5 6 7
Key
Specified conditions 1: water temperature 2 °C; ambient temperature –6 °C; evaluation period 12 h; permitted ice
formation 50%; indoor
formation 50%; outdoor
A)
Dimensions in accordance with BS EN 1057.
B)
NOTE 2 Some of the insulation thicknesses given are too large to be applied in practice but are included to
highlight the difficulty in protecting small diameter pipes against freezing. To provide the appropriate degree
of frost protection to certain sizes of pipes, it may be necessary to provide additional heat to the system, for
example by circulating the water or heat tracing.
NOTE 3 Assumed densities (/) and heat capacities (CP) are as follows:
— / water = 1 000 kg/m3, CP water = 4 200 J/kg · K;
— / steel = 7 840 kg/m3, CP steel = 455 J/kg · K;
— / copper = 8 900 kg/m3, CP copper = 390 J/kg · K.
© BSI 2009 • 53
Table 30 Minimum insulation thickness to protect against freezing – Selected domestic cold water
systems (12 hour period)

(mm) (bore)
(mm) (= (= (= (= (= (= (= (= (= (=
0.020 0.025 0.030 0.035 0.040 0.020 0.025 0.030 0.035 0.040
Copper pipes A)
15.0 13.6 20 30 43 62 88 23 35 53 78 113
22.0 20.2 9 12 16 20 24 10 14 18 23 28
28.0 26.2 6 8 10 12 14 7 9 11 13 16
35.0 32.6 5 6 7 9 10 5 7 8 10 11
42.0 39.6 4 5 6 7 8 4 5 6 7 9
54.0 51.6 3 4 4 5 6 3 4 5 5 6
76.1 73.1 2 3 3 4 4 2 3 3 4 4
B)
Steel pipes
21.3 16.1 15 21 29 38 50 18 26 35 48 64
26.9 21.7 9 12 15 18 22 10 13 17 21 26
33.7 27.3 7 8 10 12 15 7 9 12 14 17
42.4 36.0 5 6 7 8 10 5 6 8 9 11
48.3 41.9 4 5 6 7 8 4 5 6 7 9
60.3 53.0 3 4 5 5 6 3 4 5 6 7
76.1 68.8 2 3 3 4 4 3 3 4 4 5
Key
formation 50%; normal installation, i.e. inside the building and inside the envelope of the structural insulation
formation 50%; extreme installation, i.e. inside the building but outside the envelope of the structural insulation
A)
B)
NOTE 1 Some of the insulation thicknesses given are too large to be applied in practice. The purpose of
including very high thicknesses is to demonstrate that the application of a material of the given thermal
conductivity is not able to provide the degree of frost protection on the pipe size indicated under the design
conditions. Therefore in order to increase the degree of frost protection it is necessary to increase the pipe size,
select an insulation with a lower thermal conductivity or use some means of putting heat back into the system.
54 • © BSI 2009
Table 31 Minimum insulation thickness to protect against freezing – Selected domestic cold water
systems (8 hour period)

(mm) (bore)
(mm) (= (= (= (= (= (= (= (= (= (=
0.020 0.025 0.030 0.035 0.040 0.020 0.025 0.030 0.035 0.040
Copper pipes A)
15.0 13.6 11 15 20 26 34 12 17 23 31 41
22.0 20.2 6 7 9 11 13 6 8 10 12 15
28.0 26.2 4 5 6 7 9 4 6 7 8 10
35.0 32.6 3 4 5 6 7 4 4 5 6 7
42.0 39.6 3 3 4 5 5 3 4 4 5 6
54.0 51.6 2 3 3 3 4 2 3 3 4 4
76.1 73.1 2 2 2 3 3 2 2 2 3 3
B)
Steel pipes
21.3 16.1 9 12 15 19 24 10 14 18 23 29
26.9 21.7 6 7 9 11 13 6 8 10 12 15
33.7 27.3 4 5 7 8 9 5 6 7 9 10
42.4 36.0 3 4 5 5 6 3 4 5 6 7
48.3 41.9 3 3 4 5 5 3 4 4 5 6
60.3 53.0 2 3 3 4 4 2 3 3 4 4
76.1 68.8 2 2 2 3 3 2 2 3 3 3
Key
Specified conditions 1: water temperature 7 °C; ambient temperature –6 °C; evaluation period 8 h;
permitted ice formation 50%; normal installation, i.e. inside the building and inside the envelope of the structural
insulation
Specified conditions 2: water temperature 2 °C; ambient temperature –6 °C; evaluation period 8 h;
permitted ice formation 50%; extreme installation, i.e. inside the building but outside the envelope of the structural
insulation
A)
B)
NOTE 1 Some of the insulation thicknesses given are too large to be applied in practice. The purpose of
including very high thicknesses is to demonstrate that the application of a material of the given thermal
conductivity is not able to provide the degree of frost protection on the pipe size indicated under the design
conditions. Therefore in order to increase the degree of frost protection it is necessary to increase the pipe size,
select an insulation with a lower thermal conductivity or use some means of putting heat back into the system.
© BSI 2009 • 55
Annex A (informative) Underlying methodology
A.1 Determination of thicknesses for environmental

insulation thickness for process pipework and
equipment to control heat loss
Table 21 provides thicknesses of insulation satisfying the maximum
permissible heat losses for process pipework and equipment.
Larger pipes invariably experience greater heat losses and as such, in
common with BS 5422:2001 and BS 5422:1990, it was recognized that
it is not practical for the heat loss per metre of pipe to be constant for
pipes of differing diameters and operating temperatures.
In line with other industries it was decided to pursue a change
in net income methodology as a means to determine the most
environmentally appropriate insulation thickness. A change in net
income methodology concentrates on minimizing annual outgoings.
Only interest on the capital is considered, not the capital itself.
The objective of this methodology is to select a thickness of insulation
which minimizes the total annual cost as follows:
C T = PDCI + CC
where
CT is the total cost per year;
CI is the cost of the installation;
CC is the total cost of carbon used;
PD is the percentage discount rate;
and
⎛C ⎞
( )
CI = 1+ PG ⎜ L ⎟
⎝ PI ⎠
where
CL is the cost of the insulation;
PI is the percentage material cost of a project;
PG is the percentage gross margin.
Any thickness of insulation specified should match the same maximum
permissible heat loss as this calculated thickness of insulation.
A.2 Social cost of carbon

All energy used is assumed to have not only a direct financial cost
but also an indirect cost which reflects costs arising from the social
implications of carbon emissions. This indirect social cost of carbon
is calculated based on a standard government guideline. The value
assumed is laid out in Table A.1.
The energy use of a system (EI) was defined as follows:
EI = qIh
where
qI is the heat loss in kW/m;
h is the number of hours.
56 • © BSI 2009
Each fuel has a particular carbon loading, which reflects the quantity
of carbon released as the fuel is expended. Using this value the carbon
use of a system (CC) was derived using the following equation:
(
CC = EI CE + LCC SCC )
where
EI is the annual energy not saved in kWh/m;
CE is the price of energy per kWh;
LC is the carbon loading of the fuel per kWh;
CSCC is the additional social cost attributed to carbon.
NOTE A conversion factor may be required to adjust for the social cost of
carbon dioxide versus the social cost of carbon.
A.3 Calculation of heat loss

Heat losses were calculated in accordance with the methodology
laid out in BS EN ISO 12241:1998. All variables required by
BS EN ISO 12241:1998 which have been assumed in the creation of the
thickness tables contained within this standard are detailed in Table C.1.
All heat losses have been calculated to one thousandth of a W/m or

W/m2, as applicable.
A.4 Implementation of methodology

For the creation of the tables stated in this standard a spreadsheet was
used and the minimum total cost was derived empirically. The heat loss
from the next largest whole millimetre of insulation to the minimum
was selected and used as the maximum permissible heat loss.
Table A.1 Variables assumed in development of methodology for process

pipework tables
Units Value
Fuel type — Gas
Fuel price £/kWh 0.01
Carbon loading kg/kWh 0.1944
Utilization rate h/yr 8400
Insulation cost proportion % 14
Social cost of carbon £/tonne 82.5
Discount rate %/yr 0.035
3
Volumetric insulation cost £/m 404
Emissivity of outer surface of — 0.05
insulated system
© BSI 2009 • 57
Table A.2 Reference thermal conductivities of insulation
Operating temperature of Thermal conductivity

insulated system
(°C) [W/(m · K)]
100 0.041
200 0.048
300 0.056
400 0.065
500 0.076
600 0.087
700 0.100
Annex B (informative) Default values for use in

BS EN ISO 12241:1998 heat transfer
calculations
B.1 General
Complete information is not always available at the preliminary design
stages. Additionally, the effect that small changes in some design
parameters can have may not be immediately apparent. To provide
common guidance on the selection of physical data, values of surface
emissivity are given in Table B.1 for various common surfaces, together
with typical default information for other physical properties.
B.2 Default data

The information given in Table B.2 is intended to provide assistance
to the user on the following basis. Conditions shown in italics are the
“most onerous”. These conditions will require the largest insulation
thickness for a given application. The values shown in parentheses ( )
are “typical” default values.
The information should be used only as general guidance in the
absence of specific site data. It is extremely important to note that
physical variations that result in a change from laminar to turbulent
airflow over the insulated surface may affect the validity of this
guidance. In particular, use of those default conditions annotated in the
Table should be treated with caution for the following applications:
• hot pipes located in still air and typically larger than 300 mm OD;
• hot flat surfaces located indoors typically having a height greater
than 700 mm;
• cold flat surfaces located indoors typically having a height greater
than 1 500 mm.
58 • © BSI 2009
Table B.1 Surface emissivity (!)
Material !
Aluminium, bright 0.05
Aluminium, oxidized 0.13
Aluminium foil, bright reinforced 0.05
Aluminium foil, polyester faced reinforced 0.40
Alu-zinc 0.18
Austenitic steel 0.15
Brass, dull tarnished 0.61
Brass, unoxidized 0.035
Cast iron (and iron) 0.35
Cast iron, rusted or oxidized 0.65
Chrome, polished 0.10
Cloth 0.90
Copper, commercial scoured to a shine 0.07
Copper, oxidized 0.70
Copper, polished 0.02

Fire brick 0.75
Galvanized steel, blank 0.26
Galvanized steel, dusty 0.44
Paint, black 0.95
Paint, other colours 0.90
Paint, white 0.85
Paint, aluminium weathered 0.55
Paint, aluminium new 0.30
Roofing felt 0.94
Rubber, black 0.95
Rubber, grey 0.85
Steel 0.35
Steel, black painted 0.90
Steel, oxidized 0.80
White lacquer 0.95
NOTE The above values provide a useful guide to surface emissivity.
However, it should be noted that the emissivity of a material varies
with temperature and surface finish. Therefore, the precise material
emissivity should be ascertained where a high degree of accuracy is
required.
© BSI 2009 • 59
Table B.2 Default data for use in BS EN ISO 12241:1998 calculations
Variable Flat or Condition

cylindrical P1 P2 P3 P4
Diameter Flat N/A N/A N/A N/A
a) a)
Cylindrical Largest Largest Largest Smallest
Orientation Flat N/A N/A N/A N/A
Cylindrical Vertical Horizontal Horizontal N/A
b) b) c)
Height Flat Smallest Greatest Greatest N/A
(600 mm for (600 mm for (600 mm for
horizontal horizontal horizontal
ducts, 3 000 mm ducts, 3 000 mm ducts, 3 000 mm
for vertical ducts for vertical ducts for vertical ducts
and for vessels) and for vessels) and for vessels)
Cylindrical N/A N/A N/A N/A
Surface Flat Highest Lowest Lowest N/A
emissivity Cylindrical Highest Lowest Lowest N/A
Air velocity Flat Highest (still air) Lowest (still air) Lowest (still air) N/A
Cylindrical Highest (still air) Lowest (still air) Lowest (still air) N/A
Ambient air Flat Lowest for hot Highest (20 °C) Highest (25 °C) Lowest
temperature surfaces, highest
for cold (20 °C)
Cylindrical Lowest for hot Highest (20 °C) Highest (25 °C) Lowest
surfaces, highest
for cold (20 °C)
Key
P = Purpose of insulation:
P1 = Reduce total heat loss/gain;
P2 = Minimize temperature on hot surfaces;
P3 = Control condensation on cold surface;
P4 = Retard freezing.
NOTE 1 The use of annotated default conditions should be treated with caution for the following
applications.
a) Hot pipes located in still air and typically larger than 300 mm OD.
b) Hot flat surfaces located indoors typically having a height greater than 700 mm.
c) Cold flat surfaces located indoors typically having a height greater than 1 500 mm.
60 • © BSI 2009
Annex C (informative) Summary of criteria used to establish

the tables
The criteria used to establish the tables are summarized in Table C.1.
Table C.1 Summary of criteria used to establish the tables
Table Description Horizontal Height Outer Ambient Ambient Relative Evaluation Contents Max
or vertical (flat surface air air humidity time temp. °C outer
(pipes surfaces emissivity velocity temp. °C (r.h.) and and ice surface
only) only) m/s dewpoint formation temp.
m temp. °C
1 Vapour — — — — — — — –40 to —
barrier +10
permeances
2 Refrigeration Horizontal 0.6 0.90 0 20 70% — –40 to 0 —
condensation 14.4 °C
5 Refrigeration Horizontal 0.6 0.05 0 25 80 % — –40 to 0 —
6 Chilled Horizontal 0.6 0.90 0 25 80% — 0, 5, 10 —

and cold 21.3 ºC
condensation
and cold 21.3 ºC
condensation
and cold 21.3 ºC
condensation
and cold 21.3 ºC
condensation
10 Chilled Horizontal 0.6 0.05 0 25 — — 0, 5, 10 —
and cold
indicative
11 Chilled Horizontal 0.6 0.90 0 25 — — 0, 5, 10 —
and cold
indicative
12 Ductwork Horizontal 0.6 0.05, 0.44, 0 25 80% — 0, 5, 10, —
condensation 0.90 21.3 ºC 15
13 Ductwork Horizontal 0.6 0.05, 0.44, 0 15 — — 35 —
indicative 0.90
14 Ductwork Horizontal 0.6 0.05, 0.44, 0 25 — — 13 —
indicative 0.90
15 Non-domestic Horizontal 0.6 0.05 0 15 — — 75, 100, —
heating 125
16 Non-domestic Horizontal 0.6 0.90 0 15 — — 75, 100, —
heating 125
17 Non-domestic Horizontal 0.6 0.05 0 15 — — 60 —
hot water
18 Non-domestic Horizontal 0.6 0.90 0 15 — — 60 —
hot water
© BSI 2009 • 61
Table C.1 Summary of criteria used to establish the tables (continued)
Table Description Horizontal Height Outer Ambient Ambient Relative Evaluation Contents Max
or vertical (flat surface air air humidity time temp. °C outer
(pipes surfaces emissivity velocity temp. °C (r.h.) and and ice surface
only) only) m/s dewpoint formation temp.
m temp. °C
19 Domestic Horizontal 0.6 0.05 0 15 — — 60 —
heating and
hot water
20 Domestic Horizontal 0.6 0.95 0 15 — — 60 —
heating and
hot water
21 Process heat Horizontal 0.6 0.05 0 20 — — 100 to —
loss 700
22 Horizontal 0.6 0.90 0 20 — — 100 to 59
Control 700
of surface
temperature

23 Horizontal 0.6 0.05 0 20 — — 100 to 50
Control 700
of surface
temperature

24 Horizontal 0.6 0.90 0 20 — — 100 to 50
Control 700
of surface
temperature

25 Heat loss Horizontal 0.6 0.90 0 20 — — 50 to 700 —
from bare
steel pipes
from bare
bright
copper pipes
from bare
oxidized
copper pipes
28 Industrial — — — 0 –10 — 12 h nil 5 —
process and 10%
freezing
29 Commercial — — — 0 –6, –10 — 12 h 50% 2 —
and
institutional
freezing
30 Domestic — — — 0 –6 — 12 h 50% 2, 7 —
freezing
31 Domestic — — — 0 –6 — 8 h 50% 2, 7 —
freezing
Annex D (informative) Dimensions of steel, copper and

plastic pipes
Table D.1 and Table D.2 give the outside diameters of steel and copper
pipes and are taken from BS EN 10220 and BS EN 1057.
Further information on the relative thermal performance of steel,
copper and plastic pipes with respect to diameter is given in Annex H.
62 • © BSI 2009
Table D.1 Outside diameter of steel pipe (from BS EN 10220)
Nominal size Outside diameter

mm in mm in
10 ⁄ 38 17.2 0.677
20 ¾ 26.9 1.059
25 1 33.7 1.327
32 1¼ 42.4 1.669
40 1½ 48.3 1.900
50 2 60.3 2.375
65 2½ 76.1 3.000
80 3 88.9 3.500
90 3½ 101.6 4.000
100 4 114.3 4.500
125 5 139.7 5.500
150 6 168.3 6.625
200 8 219.1 8.625
250 10 273.0 10.750
300 12 323.9 12.750

350 14 355.6 14.000
400 16 406.4 16.000
450 18 457.0 18.000
500 20 508.0 20.000
600 24 610.0 24.000
NOTE 1 This table gives sizes of pipe commonly used in the engineering and process industries.
NOTE 2 Although the pipework may be ordered and referred to generally by quoting nominal (metric) sizes
and thickness, for insulating materials, the listed outside diameters should be quoted for pipe conforming to
specific British Standards.
Table D.2 Outside diameter of copper pipe (from BS EN 1057)
Outside diameter Internal diameter (bore)

mm mm
10 8.8
12 10.8
15 13.6
22 20.2
28 26.2
35 32.6
42 39.6
54 51.6
76.1 73.1
108 105.0
NOTE 1 This table gives sizes of pipe commonly used in the engineering and process industries.
NOTE 2 Although the pipework may be ordered and referred to generally by quoting nominal (metric) sizes
and thickness, for insulating materials, the listed outside diameters should be quoted for pipe conforming to
specific British Standards.
© BSI 2009 • 63
Annex E (informative) Definition of “non-combustible”, “limited

combustibility”, Class O (national class),
Class 1 (national class), Class A (European
class) and Class B (European Class).
E.1 Non-combustible materials

A non-combustible material is one which:
• is classified non-combustible in accordance with BS 476-4; or
• does not flame and does not cause any rise in temperature on
either the centre (specimen) or furnace thermocouples when
tested to BS 476-11; or
• is classified A1 in accordance with BS EN 13501-1.
E.2 Materials of limited combustibility

A material of limited combustibility is one which:
• is non-combustible in accordance with E.1; or
• has a density of at least 300 kg/m3 which, when tested to

BS 476-11, does not flame for more than 10 seconds and does
not cause a rise in temperature on the centre (specimen)
thermocouple exceeding 35 °C and a rise exceeding 20 °C on the
furnace thermocouple; or
• is classified A2 in accordance with BS EN 13501-1.
E.3 Class 1 (national class) materials

A Class 1 (national class) material is one which:
• has a Class 1 surface spread of flame rating in accordance with
BS 476-7; or
• is of limited combustibility in accordance with E.2; or
• is non-combustible in accordance with E.1.
Class 1 is the highest rating of the four classes defined in BS 476-7
(Classes 1, 2, 3 and 4).
E.4 Class O (national class) materials

A Class O (national class) material is one which:
• has a Class 1 surface spread of flame rating in accordance with
BS 476-7 and has a fire propagation index of (I) of not more
than 12.0 and a sub-index (i1) of not more than 6.0 in accordance
with BS 476-6; or
• is of limited combustibility in accordance with E.2; or
• is non-combustible in accordance with E.1.
Class O is a term defined in Approved Document B of Building
Regulations and is not a classification identified in any British
Standard test.
64 • © BSI 2009
E.5 Classes A1, A2, B, C, D, E and F (European class)

materials
Materials are classified A1, A2, B, C, D, E or F in accordance with
BS EN 13501-1.
Euro-class A1 is the safest fire classification, and Euro-class E is the
most fire hazardous. Products with Euro-classes A1, A2 and B do not
flash over, whereas those with Euro-classes C, D and E do. Euro-class
F denotes products, which have not been tested or do not meet the
requirements of classes A1 to E.
British Standard classifications do not necessarily correspond to
European (EN) classifications and a product cannot be assumed to
meet any class unless tested in accordance with the relevant standard.
Annex F (normative) Method for assessing the system load for

refrigeration pipe-work
F.1 Determination of total system heat gain

The total system heat gain (x) shall be calculated from the sum of
the heat gains of the various components of the system, in both air
conditioning and refrigeration applications. This calculation shall
adopt standard methodologies for which both ASHRAE and CIBSE
provide appropriate guidance (these normally exclude pipe-work).
NOTE 1 In most cases the total system heat gain will have been
calculated according to the CIBSE methodology by the relevant building
service engineer with the compressors correctly dimensioned to meet this
demand.
NOTE 2 Further information can be obtained from the CIBSE Guides,
particularly Volume A [14], and the ASHRAE Handbooks, in particular that
covering Systems and Equipment [15].
F.2 Determining the Coefficient of Performance (CoP) for

the system
NOTE The CoP of a refrigeration system describes the additional
efficiency improvement arising from the direct expansion of the
refrigerant, and the value for the CoP is therefore defined for each
refrigerant type and is determined by reference to the appropriate
Mollier diagram.
In order to establish the real impact of the total system heat gain (x)
on the energy demand of the system, the value shall be adjusted using
the CoP as follows:
x
= y1
CoP
where
x is the total system heat gain;
y1 is the energy demand.
© BSI 2009 • 65
F.3 Assessing the distribution pipe-work load

NOTE 1 The contribution of distribution pipe-work to the total system
heat gain might be relatively small. However, there are circumstances
where the contribution from distribution pipe-work is significant (defined
as greater than 5%) and, under these circumstances, reference should be
made to the thicknesses specified in Table 10 and Table 11 (chilled and
cold water, indicative).
In order to determine whether the contribution from distribution
pipe-work is greater than 5%, heat gains shall be calculated according
to BS EN ISO 12241:1998 on the assumption that the pipe-work is
already insulated to control condensation assuming the use of a
high emissivity surface (emissivity = 0.90). The resulting pipe-work
heat gain (z) shall then be used to determine the energy demand (y2)
arising from the distribution pipe-work as follows:
z
= y2
CoP
where
z is the total pipework heat gain
y2 is the energy demand.
The percentage of the overall system load [I] represented by the
pipework shall then be given by:

⎡ y2 ⎤
I=⎢ ⎥ × 100%
(
⎢⎣ y 1 + y 2 ) ⎥⎦
NOTE 2 This assumes that y1 has been calculated without any

consideration of distribution heat gains.
NOTE 3 As can be seen from F.2 and F.3, the same CoP is common to both
calculations and can be cancelled out in the final determination of the
percentage impact. Accordingly, there is normally no need to consider the
impact of CoP for calculation purposes.
NOTE 4 The following is an example calculation of distribution
pipe-work load as a percentage of total heat load.
A small supermarket has employed a chiller rated at 2 000 W to run
the refrigeration units in its store. The lines are 22 mm copper pipes
running at –10 ºC in an ambient temperature of 25 ºC and have been
insulated using 19 mm of high emissivity closed cell insulation to
prevent condensation.
The heat gain to this insulated pipework is 6.71 W/m.
Since the chiller is rated at 2 000 W it is reasonable to assume that this
is the maximum heat load of the system (the maximum load may in
fact be much lower). 5% of this load would therefore be 100 W.
<5% of total system load
The chiller plant has been positioned such that 10 m of distribution
pipework is required. Therefore in order to achieve the target of
reducing heat gains to the distribution pipework to less than 5% of
the total system load the maximum permissible heat gain will be:
100
qmax = = 10 W/m
10
Since the heat gain to the distribution pipework when insulated to
prevent condensation formation already limits the linear heat gain to
less than this (6.71 W/m), no further insulation thickness is required.
66 • © BSI 2009
>5% of total system load

The chiller plant has been positioned such that 20 m of distribution
pipework is required. Therefore in order to achieve the target of
reducing heat gains to the distribution pipework to less than 5% of
the total system load the maximum permissible heat gain will be:
100
qmax = = 5 W/m
20
As the heat gain of the distribution pipework does not limit the
distribution pipework to less than this it will be necessary in this case
to select a greater thickness of insulation.
This thickness should be calculated using 5 W/m as the maximum
permissible heat gain.
Annex G (informative) Calculation of economic insulation thickness

G.1 Principle
The cost of the energy consumed by a process and the cost of providing
insulation to reduce this consumption is different for every project.
The installation of the economic thickness of insulation results in the
lowest combined cost of insulation plus energy consumption over a

given period of time (evaluation period).
NOTE Figure G.1 illustrates this principle.
Figure G.1 Economic thickness
Total cost
Cost of lost heat

Cost, £
Minimum
total cost
Cost of insulation and

installation
Economic thickness
Thickness of insulation
© BSI 2009 • 67
G.2 Method of calculating economic thickness

The following information is typical of that needed to calculate the
economic insulation thickness:
a) cost of fuel;
b) process efficiency (e.g. boiler efficiency);
c) total hours of operation per year;
d) number of years over which the investment in insulation is to be
evaluated;
e) installed cost of the proposed insulation in various thicknesses;
NOTE 1 Total installed cost encompasses insulation material, fixings,
cladding, labour and all ancillaries.
f) heat transfer, both insulated and uninsulated.
NOTE 2 Heat transfer (usually stated in W/m for pipes and W/m2 for
flat surfaces) depends on type of insulation, insulation thickness,
pipe diameter, pipe orientation, height of flat surfaces, operating
temperature, surface emissivity of outer face, air velocity and
ambient air temperature.
The economic insulation thickness should be calculated either
by tabulation, as follows, or by another method that can be

demonstrated to give the same result.
1) Starting with the uninsulated condition, tabulate the cost of
installing successive, commercially available thicknesses of a
particular insulation material (including labour and ancillaries).
NOTE 3 Inclusion of the uninsulated condition provides a
comparison of potential savings. The additional costs associated with
the installation of multiple layers of insulation should be considered.
2) Tabulate the cost of the energy consumption for each of the
insulation thicknesses considered over the evaluation period.
3) Add the costs to identify the minimum total and the associated
economic insulation thickness.
Annex H (normative) Non-standard pipe diameters and

plastic pipes
H.1 General
The thicknesses of insulation provided by the tables in this standard
have been calculated for standard diameter copper or steel pipes.
H.2 Non-standard steel and copper pipe diameters

For steel or copper pipes with diameters not shown in the relevant
table, determination of the appropriate thickness of insulation shall
be as follows.
a) Thicknesses of insulation to control condensation. For an
intermediate pipe diameter not listed in the tables providing
guidance on the control of condensation (Table 2 to Table 9), the
thickness of insulation shown for the nearest larger diameter
listed shall be used unless the thickness of insulation is calculated
68 • © BSI 2009
from first principles in accordance with BS EN ISO 12241:1998,

using the calculation process specified in Annex I.
NOTE 1 A summary of criteria is given in Annex C.
b) Thicknesses of insulation to control surface temperature. For
an intermediate pipe diameter not listed in the tables providing
guidance on the control of surface temperature (Table 22,
Table 23 and Table 24), the thickness of insulation shown for the
nearest larger diameter listed shall be used unless the thickness
of insulation is calculated from first principles in accordance with
BS EN ISO 12241:1998, using the calculation process specified in
Annex I.
c) Thicknesses of insulation to protect against freezing. For an
intermediate pipe diameter not listed in the tables providing
guidance to retard freezing (Table 28 to Table 31), the thickness
of insulation shown for the nearest smaller diameter listed shall
be used unless the thickness of insulation is calculated from first
principles in accordance with BS EN ISO 12241:1998, using the
calculation process specified in Annex I.
d) Thicknesses of insulation to control heat transfer. The

methodology set out in this standard to control heat transfer
ensures that there is a unique maximum permissible heat transfer
for each pipe, which forms the benchmark performance for
compliance with this standard.
The maximum permissible heat transfer applicable to a steel or
copper pipe with a diameter not shown in Table 10, Table 11 or
Table 13 to Table 21 shall be calculated from first principles in
accordance with Annex A (for Table 21 only) and Annex I. For
an intermediate pipe diameter not listed in these tables, it will
in most cases be sufficient to undertake calculations using the
maximum permissible heat gain shown for the nearest larger
diameter listed.
H.3 Plastic pipes

The tables of insulation thicknesses in this standard apply to metal
pipes. Where plastic pipes are used, determination of the appropriate
thickness of insulation shall be as follows.
a) Thicknesses of insulation to control condensation. For an
intermediate plastic pipe diameter not listed in the tables
providing guidance on the control of condensation (Table 2
to Table 9), the thickness of insulation shown for the nearest
larger diameter listed shall be used unless the thickness of
insulation is calculated from first principles in accordance with
BS EN ISO 12241:1998, using the calculation process specified
in Annex I. The performance of the system is then undertaken
considering the plastic pipe wall to be an additional layer of
insulation (i.e. a “double-layer” calculation).
b) Thicknesses of insulation to control surface temperature. For
an intermediate plastic pipe diameter not listed in the tables
© BSI 2009 • 69
providing guidance on the control of surface temperature

(Table 22, Table 23 and Table 24), the thickness of insulation
shown for the nearest larger diameter listed shall be used unless
the thickness of insulation is calculated from first principles in
accordance with BS EN ISO 12241:1998, using the calculation
process specified in Annex I. The performance of the system
is then undertaken considering the plastic pipe wall to be an
additional layer of insulation (i.e. a “double-layer” calculation).
c) Thicknesses of insulation to protect against freezing. The tables in
this standard providing guidance on protection against freezing
relate to the specific steel and copper pipes shown. For plastic
pipes, it is recommended that calculations are undertaken from
first principles in accordance with BS EN ISO 12241:1998, using the
calculation process specified in Annex I. Further guidance may be
required from the pipe manufacturer regarding the performance
of specific plastic pipes at sub-zero temperatures.
d) Thicknesses of insulation to control heat transfer. The
methodology set out in this standard to control heat transfer
ensures that there is a unique maximum permissible heat

transfer for each pipe, which forms the benchmark performance
for compliance with this standard. When considering the
comparative heat losses of pipes made from materials with high
thermal conductivities, the wall thickness of each pipe does not
have a significant thermal resistance. As a result, it is reasonable
to conclude that the use of copper and steel pipes of identical
outer diameter will, in practice, result in comparable heat transfer
regardless of the pipe wall thickness.
It is however recognized that, when working with plastic pipes
with lower thermal conductivity values and larger wall thicknesses,
this may not always be a reasonable conclusion. Thus, in cases
where it is intended to take the insulating properties of the pipe
wall into consideration, the maximum permissible heat loss shall
be chosen as follows:
• identify bore of chosen (plastic) pipe;
• identify outside diameter of copper pipe having identical
bore;
• select maximum permissible heat transfer based on outer
diameter of copper pipe (interpolation between sizes may be
required).
It is also acceptable to select the maximum permissible heat
transfer from the tables as if the inner bore of the plastic pipe
was the outside diameter given in Table 2 to Table 9, although
adopting this procedure may result in a requirement for greater
insulation thicknesses. The performance of the system shall
then be undertaken considering the plastic pipe wall to be an
additional layer of insulation (i.e. a “double-layer” calculation).
Alternatively, the required thickness of insulation for a plastic
pipe shall be calculated using the maximum permissible heat
transfer that corresponds to the pipe’s outer diameter only if the
insulating properties of the pipe wall are disregarded.
70 • © BSI 2009
Annex I (normative) Calculations undertaken to show

compliance with this standard
For the purposes of showing compliance with this standard:
• heat transfer shall be calculated in accordance with
BS EN ISO 12241:1998;
NOTE 1 It is to be expected that a computer program will normally
be used to undertake such calculations.
• the values used or occurring within computer calculations shall
not be manually truncated or approximated;
• where iterative calculation methods are employed, the process
shall be continued until the difference between successive
values of calculated heat flux in W/m or W/m2, or outer surface
temperature in °C, is less than 0.001;
• where declared as a whole number, the thickness of insulation
resulting from calculation shall be rounded to the next higher
whole mm; one decimal place shall be considered when rounding.
NOTE 2 For example, a calculated insulation thickness of 37.107 mm
becomes 38 mm whereas 37.090 mm becomes 37 mm.
NOTE 3 Insulation thicknesses are given for a range of thermal

conductivities appropriate to the usual materials used for the application;
thicknesses for intermediate thermal conductivities and pipe sizes can
be deduced by calculation or interpolation. For assistance in selecting
an appropriate type of insulation and suitable methods of application,
reference should be made to BS 5970.
NOTE 4 Unless otherwise stated, the temperature of the surface to be
insulated is taken to be the temperature of the fluid inside the pipe, tank,
duct, vessel or other piece of equipment.
© BSI 2009 • 71
Bibliography
Standards publications
BS 5422:1990, Method for specifying thermal insulating materials for
pipes, tanks, vessels, ductwork and equipment (in the temperature
range –40 °C to +700 °C)
BS 5422:2001, Method for specifying thermal insulating materials for
pipes, tanks, vessels, ductwork and equipment operating within the
temperature range –40 °C to +700 °C
BS 5970, Code of practice for thermal insulation of pipework and
equipment in the temperature range of −100 °C to +870 °C
BS EN ISO 13732-1, Ergonomics of the thermal environment – Methods
for the assessment of human responses to contact with surfaces –
Part 1: Hot surfaces
BS EN ISO 13732-3, Ergonomics of the thermal environment – Methods
Part 3: Cold surfaces
BS EN 14114, Hygrothermal performance of building equipment and
industrial installations – Calculation of water vapour diffusion – Cold

pipe insulation systems
BS EN 1057, Copper and copper alloys – Seamless, round copper tubes
for water and gas in sanitary and heating applications
BS EN 10255, Non-alloy steel tubes suitable for welding and
threading – Technical delivery conditions
BS EN 10220, Seamless and welded steel tubes – Dimensions and
masses per unit length
BS EN 13501-1, Fire classification of construction products and building
elements – Part 1: Classification using data from reaction to fire tests
ISO/TS 13732-2, Ergonomics of the thermal environment – Methods
Part 2: Human contact with surfaces at moderate temperature
Other publications
[1] Scottish Building Standards Agency Technical Handbook –
Non-domestic Handbook. Edinburgh: The Stationery Office, 2007.
ISBN 978 0 114 97335 3.
[2] Scottish Building Standards Agency Technical Handbook –
Domestic Handbook. Edinburgh: The Stationery Office, 2007.
ISBN 978 0 114 97334 6.
[3] SCOTLAND. Building (Scotland) Regulations 2004 (SI 2004/406).
Edinburgh: The Stationery Office.
[4] GREAT BRITAIN. Control of Substances Hazardous to Health
Regulations 2002 (SI 2002/2677). London: The Stationery Office.
[5] GREAT BRITAIN. Building Regulations 2000 (SI 2000/2531) and
subsequent amendments. London: The Stationery Office.
[6] GREAT BRITAIN. Building Regulations (Northern Ireland) 2000
(SI 2000/389). Belfast: The Stationery Office.
72 • © BSI 2009
[7] The Building Regulations 2000 Approved Document L2B:

Conservation of fuel and power – Existing buildings other
than dwellings. London: The Stationery Office, 2006.
ISBN 978 0 117 03650 5.
[8] The Building Regulations (Northern Ireland) 2000: Technical
Booklet F2 – Conservation of fuel and power in buildings
other than dwellings. Belfast: The Stationery Office, 2006.
ISBN 978 0 337 08832 2.
[9] The Building Regulations 2000 Approved Document L2A:
Conservation of fuel and power – New buildings other
than dwellings. London: The Stationery Office, 2006.
ISBN 978 0 117 03649 9.
[10] The Building Regulations 2000 Approved Document L1A:
Conservation of fuel and power – New dwellings. London: The
Stationery Office, 2006. ISBN 978 0 117 03646 8.
[11] The Building Regulations 2000 Approved Document L1B:
Conservation of fuel and power – Existing dwellings. London:
The Stationery Office, 2006. ISBN 978 0 117 03647 5.
[12] The Building Regulations (Northern Ireland) 2000: Technical
Booklet F1 – Conservation of fuel and power in dwellings.
Belfast: The Stationery Office, 2006. ISBN 978 0 337 08824 7.

[13] Domestic Heating Compliance Guide. London: The Stationary
Office, 2006. ISBN 978 0 117 03645 1.
[14] CIBSE. Guide A: Environmental Design, 2006. ISBN 1903287669 1)
[15] ASHRAE. Handbook: Fundamentals, 2005. ISBN 1931862702 2)
1) Available for purchase from

http://www.cibse.org/index.cfm?go=publications.view&item=1.
2) Available for purchase from
http://www.cibse.org/index.cfm?go=publications.view&item=93.
© BSI 2009 • 73
BS 5422:2009
This page deliberately left blank

BRITISH STANDARD
This page deliberately left blank

British Standards Institution (BSI)
BSI is the independent national body responsible for preparing British Standards.
It presents the UK view on standards in Europe and at the international level.
It is incorporated by Royal Charter.
Revisions Information on standards

British Standards are updated by amendment or revision. Users of British BSI provides a wide range of information on national, European and
Standards should make sure that they possess the latest amendments or international standards through its Library.
editions. Various BSI electronic information services are also available which give
It is the constant aim of BSI to improve the quality of our products and details on all its products and services. Contact the Information Centre.
services. We would be grateful if anyone finding an inaccuracy or Tel: +44 (0)20 8996 7111
ambiguity while using this British Standard would inform the Secretary of Fax: +44 (0)20 8996 7048 Email: [email protected]
the technical committee responsible, the identity of which can be found
on the inside front cover. Subscribing members of BSI are kept up to date with standards
developments and receive substantial discounts on the purchase price

Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400 of standards. For details of these and other benefits contact Membership
BSI offers members an individual updating service called PLUS which Administration.
ensures that subscribers automatically receive the latest editions of Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001
standards. Email: [email protected]
Information regarding online access to British Standards via British
Buying standards Standards Online can be found at www.bsigroup.com/BSOL
Orders for all BSI, international and foreign standards publications Further information about BSI is available on the BSI website at
should be addressed to BSI Customer Services. www.bsigroup.com
Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001
Email: [email protected] Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the
You may also buy directly using a debit/credit card from the BSI Shop publications of the international standardization bodies. Except as permitted under the
on the website www.bsigroup.com/shop Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval
In response to orders for international standards, it is BSI policy to system or transmitted in any form or by any means – electronic, photocopying, recording or
otherwise – without prior written permission from BSI.
supply the BSI implementation of those that have been published This does not preclude the free use, in the course of implementing the standard of necessary
as British Standards, unless otherwise requested. details such as symbols, and size, type or grade designations. If these details are to be used for
any other purpose than implementation then the prior written permission of BSI must be
obtained. Details and advice can be obtained from the Copyright & Licensing Manager.
Tel: +44 (0)20 8996 7070 Email: [email protected]
BSI Group Headquarters

389 Chiswick High Road London W4 4AL UK
Tel +44 (0)20 8996 9001
Fax +44 (0)20 8996 7001
www.bsigroup.com/standards
raising standards worldwide™

BS5422 Insulation

Uploaded by

Copyright:

Available Formats

BS5422 Insulation

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BS5422 Insulation

Uploaded by

Copyright:

Available Formats

BS 5422:2009

Incorporating Corrigendum No. 1

BSI British Standards

Method for specifying thermal

tanks, vessels, ductwork and

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

raising standards worldwide™

Publishing and copyright information

ISBN 978 0 580 69184 3

ICS 23.020.01, 27.220, 91.100.60

The following BSI references relate to the work on this standard:

Amendments issued since publication

Amd. No. Date Text affected

C1 November 2009 Tables 4, 5, 7, 9, 14, 15, 16, 20,

Annex C (informative) Summary of criteria used to establish

Table 5 – Minimum insulation thickness for refrigeration applications

Table 11 – Indicative thickness of insulation for cooled and chilled

Table 25 – Heat loss from bare surfaces calculated in accordance with

Table C.1 – Summary of criteria used to establish the tables 61

© BSI 2009 • iii

Relationship with other publications

Information about this document

Handbook [2] cite BS 5422:2001 as a means of demonstrating

Contractual and legal considerations

of insulation that can be justiﬁed varies with the comparative costs

BS 476-6, Fire tests on building materials and structures –

3 Terms and deﬁnitions

3.4 environmental thickness

may be exposed and at which it will continue to function within the

3.13 water vapour permeance

4 Application of this standard

b) design ambient air temperature;

5.1 Physical characteristics

b) the material gives off an objectionable odour at the temperatures

5.2 Installation requirements

5.3 Thermal conductivity

5.3.2 Composite insulation

5.3.3 Design value of thermal conductivity and thermal bridges

5.4 Temperature limitations

service temperatures of the products speciﬁed, as appropriate.

5.6 Vapour barrier – Permeance requirements

NOTE 2 This is to ensure that the vapour permeance performance is

Temperature of plant (cold surface) Water vapour permeance of barrier

Where it is necessary to add additional claddings to an external vapour

NOTE 5 For further details see BS 5970.

5.7 Tests on physical properties

6.1 Information to be supplied by the speciﬁer

6.2 Physical characteristics

6.2.2 Fire performance

6.2.3 Water vapour barrier – Permeance requirements

6.3 Insulation thickness – Protection against

Outside Insulation thickness (mm)

Outside Insulation thickness (mm)

Outside Insulation thickness (mm)

Outside Insulation thickness (mm)

7 Chilled and cold water applications

7.1 Information to be supplied by the speciﬁer

7.2 Physical characteristics

7.2.2 Fire performance

7.2.3 Water vapour barrier – Permeance requirements