Atlas Copco Technical Specification

Rocket Boomer L2 C
Hydraulic tunnelling and mining rig with computer-
based drilling system for high accuracy and productivity
with two COP 1838 rock drills and BUT 35 booms.

For cross sections up to 104 m2

3010

www.atlascopco.com
2355
2025

L2 C

L2 C

720 1800 2200 900

2805 4000 1040
14170 (with BMH 6816)

All dimensions in mm.

Rocket Boomer L2 C equipped with optional cabin and service platform.

Features
• Rig Control System (RCS) with interactive operator control panels with full-colour display of the
computer-based drilling system. Automatic functions in the drilling process such as auto-collaring and
anti-jamming protection as well as improved regulation of the rock drill provide high performance
and outstanding drill steel economy. Integrated diagnostic system can immediately identify faulty
electrical components.
• COP 1838 rock drill with modern double reflex dampening giving genuine high speed drilling and
excellent drill steel economy. New lubrication system with separate lubrication of driver and gear,
pressurized sidebolts and mating surfaces gives reliable operation, low maintenance cost and long
intervals between overhauls.
• BMH 6800 heavy duty aluminium hydraulic feeds with double bottom for high torsional resistance.
Snap-on stainless steel sleeves and polymer contact pads for long life and low maintenance cost.
• BUT 35 heavy-duty booms for direct, fast and accurate positioning between holes. New powerful
feed rotation unit and increased coverage. Improved linkage bearings in main boom joints and new
axial bearings in all boom joints.
• Sturdy, articulated carrier with four wheel drive for easy manoeuvering in narrow tunnels and drifts.
Powered by a turbocharged, water-cooled 4-cylinder, low emission diesel engine for high mobility.
Four jacks for stable set up.
• Basic rig includes FOPS-approved protective roof, adjustable operator's control panel and fixed seat,
cable reel, water booster pump, screw compressor and work lights.

Main components
Rock drill 2 x COP 1838ME
Feed 2 x BMH 6800-series
Boom 2 x BUT 35G
Drilling system RCS
OEM feed beams 2000 and 6000 series
Email: [email protected]
Mob/WhatsApp/Wechat: 0086-131-4130-0453
Rocket Boomer L2 C

Rock drill COP 1838ME-07 Carrier

Drill steel R32, R38 or T38 • Deutz BF4M 1013C engine, water cooled turbocharged
Height over drill centre 88 mm 115 kW (156 hp) at 2300 rpm, 572 Nm at 1400 rpm
Impact power 20 kW • Articulated steering with +/- 38 degree steering angle
Impact rate 60 Hz • Four wheel drive
Hydraulic pressure, max. 230 bar • Hydrostatic power steering system
Rotation system separate rotation • Hydrodynamic Clark 24000 transmission
Rotation speed 0-240 rpm • Hurth 176HD front axle
Rotation torque, max. 700 Nm (alt. 540 Nm) • Hurth 176HD rear axle with +/- 8 degree oscillation
Lub. air consump. (at 3 bar) 5 l/s • Automatic differential lock on front axle, limited slip
Water consumption 1.1 l/s • Tyres front and rear 14.00 R24 Michelin XKA
Weight 171 kg • Clearence outside axles 15 degree
• Hydraulic jacks; front 2 extensible with large plates, rear 2
• Service brakes: Two separate circuits, hydraulically
Rock drill COP 1838HF-06 applied, fully enclosed wet disc brakes
Drill steel R32, R38 or T38 • Emergency and parking brakes: SAHR (Spring Applied
Height over drill centre 88 mm Hydraulic Released) fully enclosed wet disc brakes
Impact power 22 kW • Fuel tank, volume 100 l
Impact rate 73 Hz • Electric system 24 V
Hydraulic pressure, max. 250 bar • Batteries 2 x 125 Ah
Rotation system separate rotation • Tramming lights 8 x 70 W
Rotation speed,max 0-300 rpm • Illuminated stairs for platform, 2 x 70 W
Rotation torque, max. 545 Nm • Central lubrication system
Lub. air consump.(at 3 bar) 6 l/s • Silencer
Water consumption 1.2 l/s • Fire extinguisher
Weight 171 kg
• Spirit levels one for longitudinal and one for sideway
• Horn
• Shelf for drill bits and tools
Feeds • Gradeability 1:4 at max. load on drive wheels
BMH 6814 BMH 6816 BMH 6818BMH 6820 • Tramming speed on flat ground 15 km/hr (at rolling
Total length (mm) 5882 6502 7102 7677 resistance 0,05); on incline 1:8 5 km/hr
Drill steel length (mm)4310 4920 5530 6100 • Beacon warning lamp
Hole depth (mm) 4048 4668 5268 5843 • Reverse alarm
Weight,incl.rock Electronic system
drill (kg) 631 665 696 721
Feed force (kN) 20.0 20.0 20.0 20.0 • Rig Control System, CAN-based network. Versatile and
scalable to higher degree of automation.
• One adjustable, electronic control panel with colour
Boom BUT 35G display
Feed extension 1800 mm • PC-card for transfer of data and for service engineers
Boom extension 1600 mm to store preferred drill settings
Parallel holding Complete • Integrated diagnostic system
Feed roll-over 360 degrees
• Pre-set drilling parameters for up to three bit types,
e.g. big hole drilling
Max. lifting angle +70 degrees
–45 degrees
Max. swinging angle ±45 degrees Electrical system
Weight, boom only 2860 kg • Total installed power 158 kW
• Main motors 2 x 75 kW
Hydraulic system
• Voltage (as per customer specification) 400-700 V
• Frequency (as per customer specification) 50-60 Hz
• Hydraulic pumps: 2 separate units, one for each boom. • Starting method - star/delta
Each consists of two variable pumps for percussion • Electronic overload protection for electric motors
and positioning, and two constant flow pump for • Percussion hour meters on operator's display
rotation and compressor • Digital volt/amperage meter in electric cabinet
• Pumps unloaded at start • Phase sequence indicator
• System pressure, max 250 bar • Earth fault indicator
• Hydraulic oil tank, volume max 250 l, min 200 l • Battery charger
• Low oil lever indicator (incl.shut down when power • Transformer 8 kVA
supply is connected) • 2 x 1000 W working lights, halogen
• Oil temperature gauge on oil tank • Cabel reel, diameter 1600 mm
• Filtration, 16 µm
• Mineral hydraulic oil
Recommended cable size and length
Air system
Voltage Type Dimension Diameter Length
• Hydraulic driven Atlas Copco GA 5 screw compressor 2
• Capacity, max 26 l/s at 9bar 400 V H07RN-F 4G150 mm 67 mm 60 m
• Hydraulic drive, axial piston motor 10 cc 440 V H07RN-F 4G120 mm2 60 mm 75 m
• Adjustable speed 440 V Buflex 3x150+3G25 mm2 52 mm 100 m
• Air pressure guage 460-500 V H07RN-F 4G120 mm2 60 mm 75 m
460-500 V Buflex 3x150+3G25 mm2 52 mm 100 m
Water system 500-550 V H07RN-F 4G95 mm2 55 mm 90 m
500-550 V Buflex 3x120+3G25 mm2 46 mm 135 m
• Hydraulic driven water booster pump CR 16-80 660-700 V H07RN-F 4G70 mm2 49 mm 125 m
• Capacity, max 250 l/min at 15 bar boost 660-700 V Buflex 3x95+3G16 mm2 42 mm 150 m
• Min water inlet pressure 2 bar at 200 l/min 1000 V Buflex 3x50+3G10 mm2 32 mm 250 m
• Hydraulic drive, axial piston motor 10 cc
• Water pressure guage G= Protection yellow/green
• Water flow gauge Surrounding temperature < 30 degrees C.
 Rocket Boomer L2 C

Turning radius Dimensions and weights

Width 2530 mm
In mm with 16 ft feeds Height with roof down* 2355 mm
roof up* 3050 mm
Height with cabin* 3010 mm
Length (with 16 ft feeds) 14170 mm
*Alternative mounting heights (see below)
Ground clearance 370 mm
Gross weight** (rig without options) 23600 kg
Axle load* boom side 17400 kg
engine side 6000 kg
** = Depending on equipment
40
00
7360

Optional equipment
Rock drill/Drill system Cabin
• Rock drill rotation motor –05 (435 Nm, 0-370 rpm) • Large FOPS approved cabin, noise level 80 dB(A)
• Hole blowing kit, with 80 l air receiver • Rubber-damped for comfort during tramming and drilling
• Water mist flushing with external water and air supply • Safety glass. Two wipers with washer (front/rear shield)
(incl. extra hydraulic driven fan for oil cooling) • Swingable and fully adjustable pivot seat or fixed seat
• Rock drill lubrication warning kit • Possible to work standing or sitting with ergonomic panels
Feed • Additional operator's panel
• Telescopic feed BMHT 6800-series for left/right handed • Cabin light 220 V, adjustable reading lamp 24 V
booms, max 20 ft. (not in combination with ABC Regular • Fire extinguisher 6 kg (13 lbs) dry chemical ABE class III type
or ABC Total or 700 mm fixed boom segment) • Outlets socket 12 V for communication radio
• Hydraulic drill steel gripper BSH 110 for extension drilling • 220 V (10 A) electrical outlet for accessories
• Rod Adding System RAS, max 18+12 ft rods ( on booms • Spotlight 2x70 W with joy-stick control
with fixed segment max 16+10 ft) • CD-player, radio and speakers mounted in cabin
• Rig prepared for RAS • Cabin mounting heightlowered 200 mm (rig height 2810 mm)
Boom or increased 250 mm (rig height 3260 mm)
• Extended boom reach with 700 mm long fixed boom • Air conditioner/heating, hydraulic powered and water
segment (not for booms with BMHT feed or in transfered, with heater control and stepless fan and
combination with service platform) filtered inlet air.
• Fixed boom console angled outside 7° - Refrigerant R134a
• Automatic boom lubrication system, rear part of boom - Cooling capacity at 35o C 50% Rh 8.5 kW. 95o F wet bulb
• Ni-Cr plated piston rods (limited selection) on request 79.0 28.000 btu.
Software - Heating capacity - 12 kW 42.000 btu diesel power,
• Advanced Boom Control system - ABC Basic and 3 kW 10.500 btu with electric use
• Advanced Boom Control system - ABC Regular for - Airflow - 1300 m3/h, 747 cfm
computer assisted drilling. Incl.Tunnel Manager Lite Electrical system
• Advanced Boom Control system - ABC Total for • Soft start for electrical motors, for 400 - 700 V (not for
computer controlled drilling. Incl. Tunnel Manager Lite CSA approved rigs)
• Rig prepared for ABC Total • 1000 V electric system, direct start only
• Measure While Drilling - MWD, logging drill data for • Electric cable, type H07 or Buflex see recommendations
geological survey purposes • Dual controls for cable reel
Air system • Limit switch for cable reel
• Extra compressor GA 5 (not in combination with hose reel) • Plug for cable (with wire hose mesh)
Water system • Power supply (incl. male plug)
• Electric outlet for accessories, 32 Amp (Voltage = main
• Water hose reel (diam.1100 mm) for hose diam. 1½", supply voltage if no extra transformer is chosen. Not for
length 60 m at 70% filling rate (not in combination with 1000 V.)
extra transformer or extra air compressor) • Extra transformer, 15 kVA (not in combination with water
• Dual controls for hose reel hose reel and not CSA)
• Water hose diam. 1½" • CSA approved electrics (Canadian regulations)
Hydraulic system • Australian electrics according to AUS 3000
• Electric oil filling pump Miscellaneous
• Biodegradable hydraulic oil, Statoil Hydraway Bio PA 46 • Service platform HL 210-MBE
(PAO), Petro Canada Premium ECO HT-E 46/68 • Protective roof for service platform, FOPS approved
• Heater kit for hydraulic oil tank, 0.8 kW • Water and air outlet in service platform basket
Protective roof • Hydraulic Swellex pump
• Protective roof mounting height lowered 140 mm (rig • Rig washing kit, with water hose and reel (water
height roof up 2910 mm/down 2265 mm); or increased supplied from booster pump)
60 mm (rig height roof up 3110 mm/down 2415 mm) or • Manual lubrication system, grease-gun with hose and
310 mm (rig height roof up 3360 mm/down 2665 mm) reel (incl. 18 kg grease barrel)
Carrier • Service tool box for electronic network system
• Exhaust water scubber 150 l
• Exhaust catalyser
• Ansul fire suppression system, dry or wet
• Spare wheel
• Foam filled tyres
• High altitude setting of diesel engine
Rocket Boomer L2 C
Coverage area
(with 2° look-out angle)

with 700 mm long

fixed boom segment

8250
8650
8900
9300
1900

3010
2175
200

1328
2530
3035
11700
12400
12800 Scale 1:100
13400

without prior notice. © Atlas Copco Rock Drills AB 2003.03

The manufacturer reserves the right to make modifications
Rock Drilling Tools
Drifter rods Shank adapters
Dimension Min. hole dia, mm Thread Dia, mm Length, mm Part No.
R38-Hex 35-R32 45 R38 38 435 404-09101,00
T38-Hex 35-R32 45 T38 38 435 435-09101,00
T38-Hex 35-R32 Speedrod 45 R32 38 525 403-09103,00*
R38-Hex35- SR35 Speedrod 45 T38 38 525 435-09103,00*
T38-Hex 35-SR35 45 *= Intended for rod adding system, RAS, and extension
T38-Rnd 39-SR35 45 drilling with BSH 110.
T38-Hex 35-R35 48
T38-Hex 35-R35 Speedrod 48
9851 2182 01c

T38-Rnd 39-R35 48
T38-Rnd 39-R35 Speedrod 48
Couplings
Extension rods for injection drilling/RAS Thread Dia, mm Length, mm Part No.
Dimension Min. hole dia, mm R38 55 170 304-0055,00
R32 Speedrod 51 T38 55 190 335-0055,00
T38 Speedrod 64

For other dimensions and more information please see Secoroc General Catalogue, printed matter No. 9851 2156 01.