Asphalt Concrete
Asphalt Concrete
Asphalt Concrete
Asphalt concrete.
As shown in this cross-section, many older roadways are smoothed by applying a thin
layer of asphalt concrete to the existing portland cement concrete.
A layer of asphalt concrete. In road construction, a base layer of crushed rock is usually
laid down first to increase durability (see photo below)
Machine laying asphalt concrete, fed from a dump truck.
The terms "asphalt (or asphaltic) concrete", "bituminous asphalt concrete" and the
abbreviation "AC" are typically used only in engineering and construction documents and
literature. Asphalt concrete pavements are often called just "asphalt" by laypersons who
tend to associate the term concrete with Portland cement concrete only. The engineering
definition of concrete is any composite material composed of mineral aggregate glued
together with a binder, whether that binder is Portland cement, asphalt or even epoxy.
Informally, asphalt concrete is also referred to as "blacktop", particularly in North
America.
• Natural asphalt concrete can be produced from bituminous rock, found in some
parts of the world, where porous sedimentary rock near the surface has been
impregnated with upwelling bitumen. Bitumen is an oil based substance. It is
a semi-solid hydrocarbon product produced by removing the lighter
fractions (such as liquid petroleum gas, petrol and diesel) from heavy
crude oil during the refining process. As such, it is correctly known as
refined bitumen. In North America, bitumen is commonly known as
“asphalt cement” or “asphalt”. While elsewhere, “asphalt” is the term used
for a mixture of small stones, sand, filler and bitumen, which is used as a
road paving material. The asphalt mixture contains approximately 5%
bitumen. At ambient temperatures bitumen is a stable, semi-solid
substance.
A landing strip, one of the uses of asphalt concrete
Asphalt concrete is often touted as being 100% recyclable. Several in-place recycling
techniques have been developed to rejuvenate oxidized binders and remove cracking,
although the recycled material is generally not very water-tight or smooth and should be
overlaid with a new layer of asphalt concrete. Asphalt concrete that is removed from a
pavement is usually stockpiled for later use as a base course material. This reclaimed
material, commonly known by the acronym 'RAP' for recycled or reclaimed asphalt
pavement, is crushed to a consistent gradation and added to the HMA mixing process.
Very little asphalt concrete is actually disposed of in landfills. Sometimes waste
materials, such as rubber from old tires, are added to asphalt concrete as is the case with
rubberized asphalt, but there is a concern that the hybrid material may not be recyclable.
Asphalt deterioration can include alligator cracks, potholes, upheaval, raveling, rutting,
shoving, stripping, and grade depressions. In cold climates, freezing of the groundwater
underneath can crack asphalt even in one winter (by cryoturbation). Filling the cracks
with bitumen can temporarily fix the cracks, but only proper construction, i.e. allowing
water to drain away from under the road, can slow this process.
The bitumen aggregate mixture is cooked (matured) for around 6-8 hours and
once it is ready the mastic asphalt mixer is transported to the work site where
experienced layers empty the mixer and either machine or hand lay the mastic
asphalt contents on to the road. Mastic asphalt concrete is generally laid to a
thickness of around 3⁄4–1 3⁄16 inches (20-30 mm) for footpath and road applications
and around 3⁄8 of an inch (10 mm) for flooring or roof applications.
In addition to the asphalt and aggregate, additives, such as polymers, and
antistripping agents may be added to improve the properties of the final product.
Composition of Bitumen
1) Tar:
Coal tar is a brown or dark black liquid of high viscosity, which smells of naphthalene and
aromatic hdydrocarbons. Being flammable, coal tar is sometime used for heating or to fire
boilers.It can be used in coal tar soap, and is used in medicated shampoo to kill and repel head
lice, and as a treatment for dandruff.Depending upon its source of origin, TAR is classified as,
2) Coal Tar:
It is the liquid by-product of the distillation of coal to make coke. The gaseous by-product of this
process is commonly known as town gas. It is used for coating of wooden poles and sleepers,
iron poles.
3) Wood Tar:
It is obtained by the distillation of resinous wood. Wood tar contains creosote and as such has
strong preservative properties.
4) Mineral Tar:
It is the residue of the direct distillation of crude tar produced by the high temperature
carbonization of coal. It is used as a water proofing compound in masonry, steel and timber
structure. It is also used for water proofing concrete structures.
Properties of bitumen
1. Adhesion: Bitumen has the ability to adhere to a solid surface in a fluid state depending on the
nature of the surface. The presence of water on the surface will prevent adhesion.
2. Resistance to water: Bitumen is water resistant. Under some conditions water may be absorbed
by minute quantities of inorganic salts in the bitumen or filler in it.
3. Hardness: To measure the hardness of bitumen, the penetration test is conducted, which
measures the depth of penetration in tenths of mm. of a weighted needle in bitumen after a given
time, at a known temperature.
Commonly a weight of 100 gm is applied for 5 sec at a temperature of 77 0F. The penetration is a
measure of hardness. Typical results are 10 for hard coating asphalt, 15 to 40 for roofing asphalt
and up to 100 or more for water proofing bitumen.
4. Viscosity and flow: The viscous or flow properties of bitumen are of importance both at high
temperature during processing and application and at low temperature to which bitumen is
subjected during service.