Design and Development of Autonomous Ground Vehicle For Wild Life Monitoring

ISSN(Online): 2320-9801
ISSN (Print): 2320-9798
International Journal of Innovative Research in Computer

and Communication Engineering
(An ISO 3297: 2007 Certified Organization)
Vol. 2, Issue 5, May 2014
Design and Development of Autonomous

Ground Vehicle for Wild Life Monitoring
J. Anupama1, A. Kavitha2, S. Harsha3, M. Karthick4
1
PG Scholar, Department of Information and Communication Engineering, Er. Perumal Manimekalai College of
Engineering, Hosur, India
2
Assistant Professor, Department of ECE, Er. Perumal Manimekalai College of Engineering, Hosur, India
3
Systems Design Engineer, NAFEMS, India
4
Research Associate, Department of Mechanical Engineering, Government Engineering College, Hassan, India
ABSTRACT: The objective of this work was to develop a cost effective autonomous ground vehicle which would
carry out surveillance and tracking missions with respect to animal movements in forest area. The developed system
was equipped with a high frequency GPS module and Auto pilot controller, which enabled the user to define the
mission path. Thedeveloped system operates on its own, once the way points are assigned, leaving the user free to
monitor the mission. Live status of the system’s current position, speed, battery status etc. can be viewed from the
ground station. If necessary, the ground vehicle would be switched over from autonomous mode to manual mode,
enabling full control. The system was equipped with a down facing optical flow sensor and forward facing SONAR
sensor for obstacle avoidance.It was also equipped with a high end wireless, infrared camera for capture and
transmission of video under low light conditions. The vehicle is pre-programmed to return to base in case of
communication breakdown, thereby minimizing the chances of system loss.
KEYWORDS: autonomous vehicle, efficient algorithms; obstacle avoidance; SONAR sensor, surveillance, wild life
tracking
I. INTRODUCTION
Unmanned Ground Vehicles (UGV), have tremendous potential in military and civilian applications, specifically in
areas like reconnaissance, surveillance, target acquisition and monitoring etc. Usually, the vehicle will have a set of
sensors to perceive the environment, and will either autonomously make decisions about its behaviour or pass the
information to a human operator at a different location who will control the vehicle through tele-operation[1,2,3,4].
A fully autonomous robot has the competence to
• Acquire information about the milieu
• Work for aprotracted period without human mediation
• Move either all or part of itself throughout its operating milieu
• Avoid circumstances that are damaging to people, property, or itself.
An autonomous robot may also undergo a process called machine learning for accomplishing its tasks or adapting to
changing surroundings.
During the recent years, the researchers have been striving to achieve higher degree of autonomous mode in ground
vehicle to enhance operational performance by infusing microcontroller and software approach. However, it is seldom
seen in literature, any practitioner reporting the successful implementation of these models in wild life monitoring. The
extremely hostile conditions imposed by modern combat, outer space and the deep ocean environments have generated
the need for practical autonomous vehicles for military applications, space and ocean exploration. These relatively
near-team applications will drive the sophistication and cost of autonomous vehicle technology into the realm where
more mundane but more widespread applications such as automated public transportation will be possible. However,
significant technology advances will be necessary before even the simplest and most crucial applications can be
practically addressed. These advances will only be gained by implementing autonomous vehicle test beds and gaining
experience with the developing technology.
Copyright to IJIRCCE www.ijircce.com 4227

ISSN (Print): 2320-9798

In the following sections, the research efforts taken towards achieving autonomy, the structural analysis and the
developmental challenges are reviewed in detail.
II. RELATED WORK

Recent developments in technologies for sensing and control of autonomous unmanned ground vehicles (UGVs)
have demonstrated the ability to accurately determine the position and velocity information; thereby leading to better
performance of autonomous navigational abilities of UGVs [5]. In 1994, TakashiGomi, Koichi Ide and
HirokuzuMatsuo, demonstrated the crucial technique employed in a non- Cartesian way of organizing software agents
for the creation of a highly responsive control program [6].In 2007 a modification of an obstacle avoidance algorithm
was proposed.A self-sustainable robust system, where the system is able to track the path of travel initially and later
when the obstacle is detected, a new path is developed for the vehicle to travel [7]. The present work draws from these
articles among others and extends the scope to include the design, analysis and testing of an autonomous ground
vehicle for use in wildlife monitoring.
III. HARDWARE AND SOFTWARE DESCRIPTION

Hardware Design
The UGV acts as the surveillance vehicle for capturing video data from the atmosphere and transfers the data to
ground station with the help of a wireless module. It can also be switched from autonomous mode to the ground station
control mode with the help of wireless TTL module and controlling is done from the ground station. Computer-aided-
design was used to design the UGV as seen in Figure 1.
Figure 1: CAD design of UGV
Figure 2: Isometric view of the body of UGV
The hardware consists of DC motors to drive the ground vehicle, a camera installed with remapping algorithm which
ensures fail safe mechanism during any kind of signal loss.This would ensure that the robot would return to the base
station (or pre-determined location) [8]. The Atmel ATmega2560 Microcontroller, chosen for its low cost, high
efficiency and ease of programming, acts as processing hub for vehicle; it is fabricated with the following components:
• Auto pilot system
• GPS

ISSN (Print): 2320-9798

• Wireless Infrared Camera

• Electronic Speed Controller
• Optic flow and Ultrasonic Sensor
• Radio Trans-receiver
Figure 3: Block diagram of on board computer with sensors
Fabricated Model
The outer structure (see figure 4 and 5)was fabricatedusing Acrylic material for the following reasons:
• can be molded into various shapes
• can withstand high stress and strain
• weather proof and shock proof property
The AGV is integrated with microcontroller, sensors, sonar, GPS, auto pilot controller, telemetry device, servo
motors, ESC, gyro meter, accelerometer, magnetometer, barometer etc. to enable the wildlife monitoring application.
The software was been compiled in Keil using Embedded ‘C’ language [9].
Figure 4: Fabricated model of the AGV

ISSN (Print): 2320-9798

Figure 5: Completed model of the AGV
IV. ANALYSIS AND TESTING

In static structural analysis the focus was towards testing fortotal deformation. Von Mises stress which is also known
as equivalent stress, shear stress and stress intensity was induced in the ground vehicle. The four wheels are fixed and
given a load of 14.709 N, force acting towards downward direction as seen in figure 6. The yield strength of acrylic
material is 69 MPa. For the applied load the Von Mises stress is 3.648 MPa, see figure 7. The result indicates thatthe
ground vehicle can withstand the applied load with no structural compromise.For the applied load strain created is
1.3097e-3 mm.The resulting stress and elastic strain diagram is shown below.
Figure 6: Applied Load on the AGV

ISSN (Print): 2320-9798

Figure 7: Elastic Strain for the Applied Load
Distortion energy theory is widely considered the most preferred failure theory used in the industry. Von Mises
stress is an excellent indicator of failure criterion. As seen in figure 8, the Von Mises stress on the AGV is lower than
the yield strength of acrylic material. Similarly, the combination of the principal stresses would also allow us to
calculate Von Mises strain or equivalent elastic strain as seen in figure 9.
Figure 8: Von Mises Stress for the applied Load
Impact Analysis
Since, it was proposed to operate the AGV in rough terrains, like forests, a mechanical impact analysis was
conducted. Cad modelling for impact design has been carried out in Catia V5 R21 software [10]. The vehicle is tested
by driving it into a test wall at 3 m/s and 10 m/s.

ISSN (Print): 2320-9798

Figure 9: Applied load
The model for the contact-impact force was developed while keeping in mind the material and the geometric
properties of the colliding surfaces. The information on the relative positions and velocities contributed to the
development of an efficient test model, as seen in figure 9, and also accounted for energy dissipation. These features
were ensured with a continuous contact force model and the deformation (if any) is considered a continuous function
during the total period of contact.
Figure 10: Directional Deformation along X – Axis
The deformation generated on the robot design is .0600044 for 3m\s velocity. The deformation is very low along x-
axis as seen in Figure 10.
For the given velocity 3 m/s (figure 11), the Von-misses stress created in the AGV is 56.511 Mpa, the material did
not fail because the yield strength of acrylic is 69 Mpa.For the given velocity 10 m/s (figure 12), the VonMises stress
created in the AGV is 79.978 Mpa.At this velocity, the material would fail because the VonMises stress value is greater
than the yield strength of the acrylic material.

ISSN (Print): 2320-9798

Figure 11: Von Mises stress for 10 m/s velocity
Figure 12: Von Mises stress for 3 m/s velocity
V. CONCLUSION AND FUTURE WORK
The autonomous unmanned ground vehicle was developed successfully and tested for structural integrity. A literature
review was conducted to study the sensor system used in autonomous UGV design, the challenges and techniques of
autonomous UGV navigation. Based on the results as seen in the testing and analysis section, it was concluded that the
system would be able to operate under harsh conditions, such as a forest zone, without compromising the intended
mission.The future prospect of project is to develop an intelligent automated guided vehicle (i-agv) based on the current
system, with defense functionalities. It can be achieved by introducing target locating and tracking mechanism. The
autonomous system could also be equipped with functionalities like high definition image and video recording, terrain
mapping, self-localization etc.Future systems could be developed utilizing an intuitive graphic user interface for UGV
navigation and thereby allowing a single station operator to command multiple UGVs simultaneously. This would
enable swarm technology or group behavior.
REFERENCES.
1. V. Sezer, C. Dikilita, Z. Ercan, H. Heceoglu, A. bner, A. Apak, M. Gokasan and A. Mugan, “Conversion of a conventional electric automobile
into an unmanned ground vehicle (UGV)”, Proceedings of the IEEE International Conference on Mechatronics, April 13-15; 2012.
2. A. Mohebbi, S. Safaee, M. Keshmiri and S. Mohebbi, “Design, Simulation and Manufacturing of a Tracked Surveillance Unmanned Ground
Vehicle”, Proceedings of the IEEE International Conference on Robotics and Biomimetices, December 14-18, 2010.

ISSN (Print): 2320-9798

3. A. Bouhraoua, N. Merah, M. AlDajani and M. ElShafei, “Design and Implementation of an Unmanned Ground Vehicle for Security
Applications”, Proceedings of the 7th International Symposium on Mechatronics and its Applications, April 20-22; 2010.
4. J. -H. Lim, S. -H. Song, J. -R. Son, T. -Y. Kuc, H. -S. Park and H. -S. Kim, “An Automated Test Method for Robot Platform and Its
Components”, International Journal of Software Engineering and Its Applications, Vol. No 4, Issue No. 3,2010.
ShashidharMuppidi, “Development of a Low Cost Controller and Navigation System for Unmanned Ground Vehicle”, Master’s Thesis, College
of Engineering and Mineral Resources, West Virginia University 2008.
5. Takashi Gomi, Koichi Ide, and Hirokazu Matsuo, “The Development of a Fully Autonomous Ground Vehicle (FAGV)” Applied AI Systems,
Inc., Canada 1994.
6. Cellini, M.; Mati, R.; Pollini, L.; Innocenti, M., "Obstacle Avoidance for Autonomous Ground Vehicles in Outdoor Environments," Intelligent
Vehicles Symposium, 2007 IEEE , vol., no., pp.258,263, 13-15 June 2007
7. Reinhold Behringer, William Travis, Rob Daily, David Bevly, WilfriedKubinger, Wolfgang Herzner and Victor Fehlberg. (2005) ‘RASCAL –
An Autonomous Ground Vehicle for Desert Driving in the DARPA Grand Challenge 2005’, IEEE Conference on Intelligent Transportation
Systems pp. 644 – 649, 2005.
8. A. Ko and H. Y. K. Lau, “Robot Assisted Emergency Search and Rescue System With a Wireless Sensor Network”, International Journal of
Advanced Science and Technology, Vol. No 3, 69-78, 2009.
Harmon, S. “The Ground Surveillance Robot (GSR): An Autonomous Vehicle Designed to Transit Unknown Terrain”, IEEE Journal of
Robotics and Automation, Vol. No. 3, Issue No. 3 pp. 266– 279, 1987.
BIOGRAPHY
Anupama. J. is a PG scholar of Er. PerumalManimekalai College of Engineering, Hosur, She has published 2
conference papers and has attended numerous workshops. Her areas of interest are robotics, autonomous ground
vehicles and micro air vehicles.

Design and Development of Autonomous Ground Vehicle For Wild Life Monitoring

Uploaded by

Copyright:

Available Formats

Design and Development of Autonomous Ground Vehicle For Wild Life Monitoring

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design and Development of Autonomous Ground Vehicle For Wild Life Monitoring

Uploaded by

Copyright:

Available Formats

ISSN(Online): 2320-9801

ISSN (Print): 2320-9798

International Journal of Innovative Research in Computer

Vol. 2, Issue 5, May 2014