Scribd
Upload
520 views

Lm393 Motor Speed Measuring Sensor Module For Arduino

This document summarizes an LM393 motor speed measuring sensor module. It detects motor speed through an optical sensor that outputs pulses to a pin when an item passes through its slot. It has digital and analog outputs, LED indicators, and is small at 32x14x7mm. It can directly connect to a microcontroller for speed detection and can also trigger alarms or relays. It operates from 3.3-5V and outputs a clean 0-5V digital signal to measure rotation speed using the pulse count.

Uploaded by

vivekanandk
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
520 views

Lm393 Motor Speed Measuring Sensor Module For Arduino

This document summarizes an LM393 motor speed measuring sensor module. It detects motor speed through an optical sensor that outputs pulses to a pin when an item passes through its slot. It has digital and analog outputs, LED indicators, and is small at 32x14x7mm. It can directly connect to a microcontroller for speed detection and can also trigger alarms or relays. It operates from 3.3-5V and outputs a clean 0-5V digital signal to measure rotation speed using the pulse count.

Uploaded by

vivekanandk
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Rajguru Electronics www.rajguruelectronics.

com

Lm393 Motor Speed Measuring Sensor Module For Arduino

Widely used in motor speed detection, pulse count, the position limit, etc. The DO
output interface can be directly connected to a micro-controller IO port, if there is a block
detection sensor, such as the speed of the motor encoder can detect.
DO modules can be connected to the relay, limit switch, and other functions, it can
also with the active buzzer module, compose alarm.

Main technical characteristics:


 Dimensions: 32 x 14 x 7mm.
 The sensor reading slot has a width of 5mm.
 Two outputs, one Digital and one Analog.
 LED power indicator.
 LED indicator of the output pulses of pin D0.

Features
 Using imported trough type optical coupling sensor, groove width 5 mm.
 The output state light, lamp output level, the output low level light.
 Covered : output high level; Without sunscreen : the output low level.
 The comparator output, signal clean, good waveform, driving ability is strong, for
more than 15 ma.
 The working voltage of 3.3 V to 5 V
 Output form: digital switch output (0 and 1)
 A fixed bolt hole, convenient installation
 Small board PCB size: 3.2 cm x 1.4 cm
 Use the LM393 wide voltage comparator Module

USES:
 The module without slot, the receiving tube conduction, module DO output low level,
shade, the DO output high level;
Rajguru Electronics www.rajguruelectronics.com

 the DO output interface can be directly connected to a microcontroller IO port, if there


is a block detection sensor, such as the speed of the motor encoder can detect.
 DO modules can be connected to the relay, limit switch, and other functions, can also
with the active buzzer module, alarm.Product connection details:The positive 3.3-1,
VCC power supply 5 v2, GND connect power cathode
 DO TTL switch signal output4, AO the module does not workShipping list:A speed
measuring sensor module

This IR speed module sensor with the comparator LM393, we can calculate the speed
of rotation of the wheels of our robot. If we place a ring gear that rotates attached to our
wheel. It could also be used as an optical switch.

The basic operation of this sensor is as follows; If anything is passed between the
sensor slot, it creates a digital pulse on the D0 pin. This pulse goes from 0V to 5V and is a
digital TTL signal. Then with Arduino we can read this pulse.

Here are the different parts:

Main parts of the encoder

Wiring specification:
 VCC Connect the positive 3.3 5 v power supply
 GND Connect power negative
 DO TTL switch signal output
 AO This module does not work
 The module do not have Analog output.

You might also like