LC216EXN

Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ● ) Final Specification

Title 21.6” WXGA TFT LCD

BUYER General SUPPLIER LG Display Co., Ltd.

MODEL *MODEL LC216EXN

www.jxlcd.com
SUFFIX SCA1(RoHS Verified)

www.jxlcd.com *When you obtain standard approval,

please use the above model name without suffix

SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE

/ H.S. SONG /Team Leader

REVIEWED BY

/ O.H. LEE / Project Leader

PREPARED BY

/ B.J. CHOI / Engineer

Please return 1 copy for your confirmation with TV Product Development Dept.
your signature and comments. LG Display Co., Ltd.

Ver 1.0 1/36

 LC216EXN
Product Specification

CONTENTS
Number ITEM Page
COVER 1

CONTENTS 2
RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS 5

3 ELECTRICAL SPECIFICATIONS 6

3-1 ELECTRICAL CHARACTERISTICS 6

3-2 INTERFACE CONNECTIONS 8

3-3 SIGNAL TIMING SPECIFICATIONS 10

3-4 SIGNAL TIMING WAVEFORMS 11

3-5 COLOR DATA REFERENCE 14

3-6 POWER SEQUENCE 15

4 OPTICAL SPECIFICATIONS 17

7
www.jxlcd.com
www.jxlcd.com
MECHANICAL CHARACTERISTICS

RELIABILITY

INTERNATIONAL STANDARDS
21

24

25

7-1 SAFETY 25

7-2 EMC 25

7-3 Environment 25

8 PACKING 26

8-1 INFORMATION OF LCM LABEL 26

8-2 PACKING FORM 26

9 PRECAUTIONS 27
9-1 MOUNTING PRECAUTIONS 27
9-2 OPERATING PRECAUTIONS 27
9-3 ELECTROSTATIC DISCHARGE CONTROL 28
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE 28
9-5 STORAGE 28
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM 28

Ver 1.0 2/36

 LC216EXN
Product Specification

RECORD OF REVISIONS

Revision No. Revision Date Page Description

0.1 Aug. 31, 2009 - Preliminary Specification (First Draft)
0.2 Dec. 15, 2009 7 Updated the Electrical Characteristics for LED Driver
9 Updated the LED Driver Connector Configuration notes.
23 Updated the Mechanical Drawings.
27 Updated the Operating Precautions.
32 Updated the Pallet Ass’y Packing.

1.0 Jan. 22, 2010 7 Updated the Electrical Characteristics for LED Driver

- Final Specification.

www.jxlcd.com
www.jxlcd.com

Ver 1.0 3/36

 LC216EXN
Product Specification

1. General Description

The LC216EXN is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system.
The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive display type which is operating in the normally black mode. It has a 21.6 inch diagonally
measured active display area with WXGA resolution (768 vertical by 1366 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arrayed in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
thus presenting a palette of more than 16.7M(6bit + A-FRC) colors.
It has been designed to apply the 8-bit 1-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.

Mini-LVDS(RGB)
EEPROM
Source Driver Circuit
SCL SDA S1 S1366

G1
Gate Driver Circuit

LVDS
Timing Controller
1Port
CN1 [LVDS Rx]
LVDS
(30pin)
TFT - LCD Panel

www.jxlcd.com
www.jxlcd.com
Select (1366 × RGB × 768 pixels)

+5.0V Power Circuit G768

Block

+24.0V, GND, Von/off LED Driver

Ext VBR-B CN401(14Pin) CN402(6Pin) Back light Assembly( 56 LED)

General Features
Active Screen Size 21.6 inches(547.7mm) diagonal
Outline Dimension 501(H) × 297(V) × 14.5(D) (Typ.)
Pixel Pitch 0.1165 mm x 0.3495 mm
Pixel Format 1366 horiz. by 768 vert. Pixels, RGB stripe arrangement
Color Depth 8-bit(D), 16.7M colors
Luminance, White 300 cd/m2 (Center 1point) (Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178(Min.), U/D 178(Min.))
Total 24.3W (Typ.)
Power Consumption
(Logic=3.3W, LED Driver=21W, EXTVBR-B=100% )
Weight 1,750g (Typ.)
Display Mode Transmissive mode, Normally black
Surface Treatment Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 13%)

Ver 1.0 4/36

 LC216EXN
Product Specification

2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.
Table 1. ABSOLUTE MAXIMUM RATINGS

Value
Parameter Symbol Unit Note
Min Max
LCD Circuit VLCD -0.3 +6.0 VDC
Power Input Voltage
Driver VBL -0.3 + 27.0 VDC
ON/OFF VOFF / VON -0.3 +5.5 VDC 1
Driver Control Voltage
Brightness VBR 0.0 +5.5 VDC
T-Con Option Selection Voltage VLOGIC -0.3 +4.0 VDC
Operating Temperature TOP 0 +50 °C
2,3
Storage Temperature TST -20 +60 °C
Panel Front Temperature TSUR - +68 °C 4
Operating Ambient Humidity HOP 10 90 %RH
2,3
Storage Humidity HST 10 90 %RH

www.jxlcd.com
Note 1. Ambient temperature condition (Ta = 25 ± 2 °C )

www.jxlcd.com
2. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39°C, and no condensation of water.
3. Gravity mura can be guaranteed below 40°C condition.
4. The maximum operating temperatures is based on the test condition that the surface temperature
of display area is less than or equal to 68°C with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 68℃. The range of operating temperature may degraded in case of
improper thermal management in final product design.

90%

60
60%

50 Storage
Humidity [(%)RH]

Wet Bulb
Temperature [°C]
40
40%
Operation
30

20
10
0
10%

-20 0 10 20 30 40 50 60 70 80

Dry Bulb Temperature [°C]

Ver 1.0 5/36

 LC216EXN
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics

It requires two power inputs. One is employed to power for the LCD circuit. The other is used for the LED
backlight and LED Driver circuit.

Table 2. ELECTRICAL CHARACTERISTICS

Value
Parameter Symbol Unit Note
Min Typ Max
Circuit :

Power Input Voltage VLCD 4.5 5.0 5.5 VDC

- 660 858 mA 1
Power Input Current ILCD
- 830 1079 mA 2
Power Consumption PLCD - 3.3 4.29 Watt 1

Rush current IRUSH - - 3.0 A 3

www.jxlcd.com
www.jxlcd.com
Notes : 1. The specified current and power consumption are under the VLCD=5.0V, 25 ± 2°C, fV=60Hz
condition whereas mosaic pattern(8 x 6) is displayed and f V is the frame frequency.
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).

White : 255Gray
Black : 0Gray

Mosaic Pattern(8 x 6)

Ver 1.0 6/36

 LC216EXN
Product Specification

Table 3. ELECTRICAL CHARACTERISTICS (Continue)

Values
Parameter Symbol Unit Notes
Min Typ Max

LED Driver :

Power Supply Input Voltage VBL 22.8 24.0 25.2 Vdc 1

Power Supply Input Current IBL_A - 0.87 0.97 A 1

VBL = 22.8V
Power Supply Input Current (In-Rush) Irush - - 1.5 A
Ext VBR-B = 100%
Power Consumption PBL - 21 23.3 W 1
On V on 2.5 - 5.0 Vdc
On/Off
Off V off -0.3 0.0 0.7 Vdc
Brightness Adjust ExtVBR-B 10 - 100 % On Duty
Input Voltage for
Control System PWM Frequency for PAL 100 Hz 4
Signals NTSC & PAL NTSC 120 Hz 4

Pulse Duty Level High Level 2.5 - 5.0 Vdc HIGH : on duty
(PWM) Low Level 0.0 - 0.7 LOW : off duty
Vdc
LED :
Life Time

Notes :
www.jxlcd.com
www.jxlcd.com 30,000 Hrs 3

1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 60
minutes at 25±2°C. The specified current and power consumption are under the typical supply Input voltage
24Vand VBR (ExtVBR-B : 100%), it is total power consumption.
2. Electrical characteristics are determined within 30 minutes at 25±2°C.
The specified currents are under the typical supply Input voltage 24V.
3. The life time is determined as the time which luminance of the LED is 50% compared to that of initial
value at the typical LED current (ExtVBR-B :100%) on condition of continuous operating in LCM state at
25±2°C.
4. LGD recommend that the PWM freq. is synchronized with two time harmonic of Vsync signal of system.
Though PWM frequency is over 120Hz (max 252Hz), function of LED Driver is not affected.
5. The duration of rush current is about 10ms.
6. Even though inrush current is over the specified value, there is no problem if I2T spec of fuse is satisfied.

Ver 1.0 7/36

 LC216EXN
Product Specification

3-2. Interface Connections

This LCD module employs two kinds of interface connection, a 30-pin connector is used for the module
electronics and 14-pin connector is used for the integral backlight system.

3-2-1. LCD Module

- LCD Connector(CN5) : KDF71G-30S-1H(Hirose) or Equivalent.
- Mating Connector : FI-X30C2L (Manufactured by JAE) or Equivalent

Table 4. MODULE CONNECTOR(CN5) PIN CONFIGURATION

Pin No. Symbol Description Note
1 GND Ground 5
2 Reserved “H” : Interlace Free Mode, “L or NC ” : Normal Operation
3 NC No Connection
4 GND Ground
5 RX0- LVDS Receiver Signal(-)
6 RX0+ LVDS Receiver Signal(+)
7 GND Ground
8 RX1- LVDS Receiver Signal(-)
9 RX1+ LVDS Receiver Signal(+)
10 GND Ground
11 RX2- LVDS Receiver Signal(-)
12 RX2+ LVDS Receiver Signal(+)
13 GND Ground
14
15
16
17
18
www.jxlcd.com
www.jxlcd.com
RXCLK-
RXCLK+
GND
RX3-
RX3+
LVDS Receiver Clock Signal(-)
LVDS Receiver Clock Signal(+)
Ground
LVDS Receiver Signal(-)
LVDS Receiver Signal(+)
19 GND Ground
20 NC No Connection
21 LVDS Select “H” : JEIDA, “L or NC” : VESA
22 NC No Connection
23 GND Ground
24 GND Ground
25 GND Ground
26 VLCD Power Supply +5.0V
27 VLCD Power Supply +5.0V
28 VLCD Power Supply +5.0V
29 VLCD Power Supply +5.0V
30 VLCD Power Supply +5.0V

Notes : 1. All GND (Ground) pins should be connected together to the LCD module’s metal frame.
2. All VLCD (Power input) pins should be connected together.
3. All Input levels of LVDS signals are based on the EIA 644 Standard.
4. Specific pins (Pin No. #2, #21) are used for Option of the LCD module.
If not used, these pins are no connection.
5. Specific pin No. #1 is used for “No signal detection” of system signal interface.
It should be GND for NSB (No Signal Black) during the system interface signal is not.
If this pin is “H”, LCD Module displays AGP (Auto Generation Pattern).

Ver 1.0 8/36

 LC216EXN
Product Specification

3-2-2. Backlight Inverter

- LED Connector : SM14B-SRSS-TB (Manufactured by JST)

- Mating Connector : SHR-14V-S-B (With protrusions) or SHR-14V-S
(Without protrusions) ; (Manufactured by JST)

Table 5. LED DRIVER CONNECTOR PIN CONFIGULATION

Pin No Symbol Description Note
1 VBL Power Supply +24.0V
2 VBL Power Supply +24.0V
3 VBL Power Supply +24.0V
4 VBL Power Supply +24.0V
5 VBL Power Supply +24.0V
6 GND Backlight Ground
7 GND Backlight Ground
8 GND Backlight Ground 1
9 GND Backlight Ground
10
11
12
www.jxlcd.com
www.jxlcd.com
GND
NC
VON/OFF
Backlight Ground
No Connection
Backlight ON/OFF control

13 EXTVBR-B External PWM 2

14 Status LED Status 3

Notes : 1. GND should be connected to the LCD module’s metal frame.

2. High : on duty / Low : off duty
3. Normal : Low (under 0.7V) / Abnormal : High (upper 3.0V)
4. Each impedance of pin #12 and 13 is over 50[KΩ] and over 50[KΩ].

◆ Rear view of LCM

PCB

14
…

Ver 1.0 9/36

 LC216EXN
Product Specification

3-3. Signal Timing Specifications

Table 6 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal
timings should be satisfied with the following specification for normal operation.

Table 6-1. TIMING TABLE for NTSC (DE Only Mode)

ITEM Symbol Min Typ Max Unit Note

Display Period tHV - 1366 - tclk

Horizontal Blank tHB 90 162 410 tclk

Total tHP 1456 1528 1776 tclk

Display Period tVV - 768 - tHP

Vertical Blank tVB 8 22 240 tHP

Total tVP 776 790 1008 tHP

DCLK fCLK 63.0 72.4 80.0 MHz

Frequency Horizontal fH 45 47.4 55 KHz

www.jxlcd.com
www.jxlcd.com
Vertical fV

Table 6-2. TIMING TABLE for PAL (DE Only Mode)

57 60 63 Hz

ITEM Symbol Min Typ Max Unit Note

Display Period tHV - 1366 - tclk

Horizontal Blank tHB 90 162 410 tclk

Total tHP 1456 1528 1776 tclk

Display Period tVV - 768 - tHP

Vertical Blank tVB 126 180 295 tHP

Total tVP 894 948 1063 tHP

DCLK fCLK 63.0 72.4 80.0 MHz

Frequency Horizontal fH 45 47.4 55 KHz

Vertical fV 47 50 53 Hz

Note The Input of HSYNC & VSYNC signal does not have an effect on normal operation(DE Only Mode).
The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate.

Ver 1.0 10/36

 LC216EXN
Product Specification

3-4. Signal Timing Waveforms

3-4-1. LVDS Input Signal Timing Diagram

0.7VDD
DE, Data
0.3VDD

tCLK
DCLK 0.5 Vcc

Valid data

1366 Invalid data 1 1366 Invalid data

DE (Data Enable)

www.jxlcd.com
www.jxlcd.com tHT
tHV

DE (Data Enable)
768 1 768

tVV

tVT

Ver 1.0 11/36

 LC216EXN
Product Specification

3-4-2. LVDS Input Signal Characteristics

1) DC Specification
LVDS -

LVDS +

V CM V IN _ MAX V IN _ MIN

# V CM = {( LVDS +) + ( LVDS - )} /2
0V

Description Symbol Min Max Unit Note

LVDS Common mode Voltage VCM 1.0 1.5 V -
LVDS Input Voltage Range VIN 0.7 1.8 V -
Change in common mode Voltage ΔVCM 250 mV -

2) AC Specification
T clk

LVDS Clock

LVDS Data
www.jxlcd.com
www.jxlcd.com tSKEW tSKEW
A

( Fclk = 1 /T clk )
A
Tclk
LVDS 1’st Clock 80%

LVDS 2nd / 3rd / 4th Clock

20%
tRF
tSKEW_min tSKEW_max

Description Symbol Min Max Unit Note

High Threshold VTH 100 300 mV
LVDS Differential Voltage 3
Low Threshold VTL -300 -100 mV
LVDS Clock to Data Skew Margin tSKEW |(0.2*Tclk)/7| ps -
LVDS Clock/DATA Rising/Falling time tRF 260 (0.3*Tclk)/7 ps 2
Effective time of LVDS teff ±360 ps -
LVDS Clock to Clock Skew Margin (Even to Odd) tSKEW_EO 1/7* Tclk Tclk -
Note 1. All Input levels of LVDS signals are based on the EIA 644 Standard.
2. If tRF isn’t enough, teff should be meet the range.
3. LVDS Differential Voltage is defined within teff

Ver 1.0 12/36

 LC216EXN
Product Specification

360ps

0.5tui tui
V+
data

VTH
Vcm
VTL

V-
360ps
data
teff

www.jxlcd.com
V+

www.jxlcd.com
tui : Unit Interval
clk

Vcm

V-
clk

Ver 1.0 13/36

 LC216EXN
Product Specification

3-5. Color Data Reference

The brightness of each primary color (Red, Green, Blue) is based on the 8-bit gray scale data input for the color.
The higher binary input, the brighter the color. Table 7 provides a reference for color versus data input.

Table 7. COLOR DATA REFERENCE

Input Color Data

RED GREEN BLUE

Color
MSB LSB MSB LSB MSB LSB

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Green (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

Basic Blue (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

www.jxlcd.com
www.jxlcd.com
White

RED (000)

RED (001)
Dark 0
1

0
1

0
1

0
1

0
1

0
1

0
1

0
1 1

0 0

1 0
1

0
1

0
1

0
1

0
1

0
1

0
1 1

0 0

0 0
1

0
1

0
1

0
1

0
1

0
1

0
1

RED ... ... ... ...

RED (254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (000) Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0

GREEN ... ... ... ...

GREEN (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0

GREEN (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

BLUE (000) Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

BLUE ... ... ... ...

BLUE (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0

BLUE (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Ver 1.0 14/36

 LC216EXN
Product Specification

3-6. Power Sequence

3-6-1. LCD Driving circuit

90%
Power Supply For LCD
VLCD 10% 10% 10%
0V

T1
T5
T2
Valid Data Vcm : LVDS Common mode Voltage

30%
Interface Signal (Tx_clock) 0V

100% T3 T4
T6
User Control Signal
(LVDS_select, Reserved)

Power for LED T7 LED ON

Parameter
www.jxlcd.com
www.jxlcd.com
Table 9. POWER SEQUENCE

Value
Unit Notes
Min Typ Max
T1 0.5 - 20 ms
T2 0 - - ms 4
T3 200 - - ms 3
T4 200 - - ms 3
T5 1.0 - - s 5
T6 - - T2 s 4
T7 0.5 - - s

Note :1. Please avoid floating state of interface signal at invalid period.
2. When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.
3. The T3/T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. If the on time of signals (Interface signal and user control signals) precedes the on time of Power (VLCD)
it will be happened abnormal display. When T6 is NC status, T6 doesn’t need to be measured.
5. T5 should be measured after the Module has been fully discharged between power off and on
period.

Ver 1.0 15/36

 LC216EXN
Product Specification

3-6-2. Sequence for LED Driver

Power Supply For LED Driver

24V (typ.)
90% 90%
VBL
10%
0V

T1 T2 T5

VON/OFF
LED ON

EXTVBR-B

T4

3-6-3. Dip condition for LED Driver

www.jxlcd.com
www.jxlcd.com T6
VBL : 24V

VBL (Typ.) x 0.8

0V

Table 9. Power Sequence for Inverter

Values
Parameter Units Remarks
Min Typ Max
T1 20 - - ms 1
T2 500 - - ms
T4 0 - ms
T5 10 - - ms
T6 - - 10 ms VBL(Typ) x 0.8

Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time.
Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.

Ver 1.0 16/36

 LC216EXN
Product Specification

4. Optical Specification

Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25±2°C.
The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of F and q
equal to 0 °.
FIG. 1 shows additional information concerning the measurement equipment and method.

LCD Module Pritchard 880 or

Optical Stage(x,y)
equivalent

50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method

Table 10. OPTICAL CHARACTERISTICS Ta= 25±2°C, VLCD=5.0V, fV=60Hz, Dclk=72.4MHz, EXTVBR-B=100%
Value

www.jxlcd.com
Parameter Symbol Unit Note

www.jxlcd.com
Contrast Ratio
Surface Luminance, white
Luminance Variation
CR
LWH
d WHITE 5P
Min
700
240
-
Typ
1000
300
-
Max
-
-
1.3
cd/m 2
1
2
3
Variation G to G σ 6 9 ms 5
Response Time
Gray to Gray (BW) G to G BW 9 13 ms 4
Rx 0.622
RED
Ry 0.344
Gx 0.338
Color GREEN
Gy Typ 0.618 Typ
Coordinates
Bx -0.03 0.152 +0.03
[CIE1931] BLUE
By 0.045
Wx 0.279
WHITE
Wy 0.292
Color Temperature 10,000 K
Color Gamut 68 %
Viewing Angle (CR>10)
x axis, right(f=0°) qr 89 - -
x axis, left (f=180°) ql 89 - -
degree 6
y axis, up (f=90°) qu 89 - -
y axis, down (f=270°) qd 89 - -
Gray Scale - - - 7

Ver 1.0 17/36

 LC216EXN
Product Specification
Notes :1. Contrast Ratio(CR) is defined mathematically as :
Surface Luminance at all white pixels
CR =
Surface Luminance at all black pixels
It is measured at center 1-point.

2. Surface luminance is determined after the unit has been ‘ON’ and 1Hour after lighting the
backlight in a dark environment at 25±2°C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.

3. The variation in surface luminance , d WHITE is defined as :

d WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5)
Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations .
For more information, see the FIG. 2.

4. Response time is the time required for the display to transit from any gray to white (Rise Time, TrR)
and from any gray to black (Decay time, TrD). For additional information see the FIG. 3.
※ G to GBW Spec stands for average value of all measured points.

5. G to G σ is Variation of Gray to Gray response time composing a picture

Xi = Individual Data
G to G (σ) =
√ Σ(Xi- u)2
N u = Data average
N : The number of Data

www.jxlcd.com
www.jxlcd.com
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 4.

7. Gray scale specification

Gamma Value is approximately 2.2. For more information, see the Table 11.
Table 11. GRAY SCALE SPECIFICATION
Gray Level Luminance [%] (Typ.)
L0 0.10
L15 0.27
L31 1.04
L47 2.49
L63 4.68
L79 7.66
L95 11.5
L111 16.1
L127 21.6
L143 28.1
L159 35.4
L175 43.7
L191 53.0
L207 66.7
L223 79.0
L239 90.2
L255 100

Ver 1.0 18/36

 LC216EXN
Product Specification

Measuring point for surface luminance & measuring point for luminance variation.

H
A

② ③

①
V
B

A : H / 4 mm
④ ⑤ B : V / 4 mm
@ H,V : Active Area

www.jxlcd.com
www.jxlcd.com FIG. 2 5 Points for Luminance Measure

Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Black or White”.

Tr Tf
100
90

Optical
Response

10
Gray(N) White Gray(N) Black
0
N = 0(Black)~255(White)

FIG. 3 Response Time

Ver 1.0 19/36

 LC216EXN
Product Specification

Dimension of viewing angle range

Normal
E Y
f = 90°, Up

f = 180°, Left
q

f = 0°, Right

f = 270°, Down

www.jxlcd.com
www.jxlcd.com FIG. 4 Viewing Angle

Ver 1.0 20/36

 LC216EXN
Product Specification

5. Mechanical Characteristics

Table 12 provides general mechanical characteristics.

Table 12. MECHANICAL CHARACTERISTICS

Item Value

Horizontal 501.0 mm

Outline Dimension Vertical 297.0 mm

Depth 14.5 mm

Horizontal 481.5 mm
Bezel Area
Vertical 272.5 mm

Horizontal 477.417 mm
Active Display Area
Vertical 268.416 mm

Weight 1,750g (Typ.), 1,850g (Max.)

www.jxlcd.com
www.jxlcd.com
Note : Please refer to a mechanical drawing in terms of tolerance at the next page.

Ver 1.0 21/36

 LC216EXN
Product Specification

<FRONT VIEW>

www.jxlcd.com
www.jxlcd.com

Ver 1.0 22/36

 LC216EXN
Product Specification

<REAR VIEW>

www.jxlcd.com
www.jxlcd.com

Ver 1.0 23/36

 LC216EXN
Product Specification

6. Reliability

Table 13. ENVIRONMENT TEST CONDITION

No. Test Item Condition

1 High temperature storage test Ta= 60°C 240h

2 Low temperature storage test Ta= -20°C 240h

3 High temperature operation test Ta= 50°C 50%RH 240h

4 Low temperature operation test Ta= 0°C 240h

Wave form : random

Vibration level : 1.0Grms
Vibration test
5 Bandwidth : 10-300Hz
(non-operating)
Duration : X,Y,Z,
each direction per 20min

Shock level : 120Grms

Shock test Waveform : half sine wave, 2ms
6
(non-operating) Direction : ±X, ±Y, ±Z

www.jxlcd.com
each direction

8
www.jxlcd.com
Humidity condition Operation

Altitude operating
storage / shipment
Ta= 40 °C ,90%RH

0 - 15,000 ft
0 - 40,000 ft

Note : Before and after Reliability test, LCM should be operated with normal function.

Ver 1.0 24/36

 LC216EXN
Product Specification

7. International Standards

7-1. Safety
a) UL 60065, Seventh Edition, Underwriters Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
c) EN 60065:2002 + A11:2008, European Committee for Electrotechnical Standardization (CENELEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
d) IEC 60065:2005 + A1:2005, The International Electrotechnical Commission (IEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
(Including report of IEC60825-1:2001 clause 8 and clause 9)

Notes
1. Laser (LED Backlight) Information

Class 1M LED Product

IEC60825-1 : 2001
Embedded LED Power (Class1M)
Power : 4.42 mW (Max.)
Wavelength : 397 ~ 773 (nm)
Width : 1.6 x 0.6 (mm)

www.jxlcd.com
www.jxlcd.com
2. Caution
: LED inside.
Class 1M laser (LEDs) radiation when open.
Do not open while operating.

7-2. EMC
a) ANSI C63.4 “American National Standard for Methods of Measurement of Radio-Noise
Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.”
American National Standards Institute (ANSI), 2003.
b) CISPR 22 “Information technology equipment – Radio disturbance characteristics – Limit and
methods of measurement." International Special Committee on Radio Interference
(CISPR), 2005.
c) CISPR 13 “Sound and television broadcast receivers and associated equipment – Radio disturbance
characteristics – Limits and method of measurement." International Special Committee on Radio
Interference (CISPR), 2006.

7-3. Environment
a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003

Ver 1.0 25/36

 LC216EXN
Product Specification

8. Packing
8-1. Information of LCM Label
a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
Mark 1 2 3 4 5 6 7 8 9 0

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Mark 1 2 3 4 5 6 7 8 9 A B C

www.jxlcd.com
www.jxlcd.com
b) Location of Lot Mark
Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one Box : 9 pcs

b) Box Size : 555 mm X 325 mm X 365 mm.

Ver 1.0 26/36

 LC216EXN
Product Specification

9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
9-1. Mounting Precautions
(1) You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes

www.jxlcd.com
deformations and color fading.

www.jxlcd.com
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating Precautions

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer
(4) Be careful for condensation at sudden temperature change.Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it can causes conductive particles and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
(10) The conductive material and signal cables are kept away from LED driver inductor to prevent abnormal
display, sound noise and temperature rising.

Ver 1.0 27/36

 LC216EXN
Product Specification

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.

www.jxlcd.com
www.jxlcd.com
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-
blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-
hexane.

Ver 1.0 28/36

 LC216EXN
Product Specification
# APPENDIX- I-1
■ Required signal assignment for Flat Link Transmitter (Pin 21 =“L or NC”)

Host System DS90C385 Timing

24 Bit or Compatible KDF71G-30S-1H Controller
RED0 51
48
RED1 52 TxOUT0- 5 RxIN0-
RED2 54 TxOUT0+ 47
6 RxIN0+
RED3 55
RED4 56
46
RED5 3 TxOUT1- 8 RxIN1-
45
RED6 50 TxOUT1+ 9 RxIN1+
RED7 2
GREEN0 4
42
GREEN1 6 TxOUT2- 11 RxIN2-
41
GREEN2 7 TxOUT2+ 12 RxIN2+
GREEN3 11
GREEN4 12

www.jxlcd.com
www.jxlcd.com
GREEN5
GREEN6
GREEN7
BLUE0
14
8
10
15
TxCLKOUT-
TxCLKOUT+
40
39

38
14
15
RxCLKIN-
RxCLKIN+

BLUE1 19 TxOUT3- 17 RxIN3-

37
BLUE2 20 TxOUT3+ 18 RxIN3+
BLUE3 22 1㏀
BLUE4 23 21 VESA / JEIDA
BLUE5 24 1 LCD Test
BLUE6 16 1㏀
BLUE7 18
Hsync 27
Vsync 28
GND
GND

Data Enable 30
LCD Module
CLOCK 31

Notes:
1. The LCD module uses a 50 ohm(Ω) resistor between positive and negative lines of T-con Internal.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘ 7’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver 1.0 29/36

 LC216EXN
Product Specification
# APPENDIX- I-2
■ Required signal assignment for Flat Link Transmitter (Pin 21 =“H”)

Host System DS90C385 Timing

24 Bit or Compatible KDF71G-30S-1H Controller
RED0 50
48
RED1 2 TxOUT0- 5 RxIN0-
47
RED2 51 TxOUT0+ 6 RxIN0+
RED3 52
RED4 54 46
RED5 55 TxOUT1- 8 RxIN1-
45
RED6 56 TxOUT1+ 9 RxIN1+
RED7 3
GREEN0 8 42
GREEN1 10 TxOUT2- 11 RxIN2-
41
GREEN2 4 TxOUT2+ 12 RxIN2+
GREEN3 6
GREEN4 7

www.jxlcd.com
40

www.jxlcd.com
GREEN5
GREEN6
GREEN7
BLUE0
BLUE1
11
12
14
16
18
TxCLKOUT-
TxCLKOUT+

TxOUT3-
39

38
14
15

17
RxCLKIN-
RxCLKIN+

RxIN3-
37
BLUE2 15 TxOUT3+ 18 RxIN3+
BLUE3 19 1㏀
BLUE4 20 21 VESA / JEIDA
BLUE5 22 1 LCD Test
BLUE6 23 1㏀
BLUE7 24
Hsync 27
Vsync
GND

28
VCC

Data Enable 30
LCD Module
CLOCK 31

Notes:
1. The LCD module uses a 100 ohm(Ω) resistor between positive and negative lines of T-con Internal.
2. Refer to LVDS transmitter data sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘ 7’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver 1.0 30/36

 LC216EXN
Product Specification
# APPENDIX- II-1

■ Packing Ass’y

www.jxlcd.com
www.jxlcd.com

NO. DESCRIPTION MATERIAL

1 LCM
2 BAG AL
3 TAPE OPP
4 PACKING, BOTTOM EPS
5 PACKING, TOP EPS
6 BOX PAPER, SW
7 TAPE OPP
8 LABEL ART

Ver 1.0 31/36

 LC216EXN
Product Specification
# APPENDIX- II-2

■ Pallet Ass’y

③
⑤
⑥

① www.jxlcd.com
www.jxlcd.com ⑦

NO. DESCRIPTION MATERIAL

1 PACKING ASS’Y -
2 PALLET PLYWOOD_1140X990X117.5
3 BAND PP
4 BAND, CLIP CLIP
5 ANGLE COVER PAPER, SW
6 LABEL ART
7 WRAP LLDPE

Ver 1.0 32/36

 LC216EXN

# APPENDIX 2 Product Specification

# APPENDIX- III

■ LCM Label

Model LC216EXN
(SC)(A1)
L5EDD5Q00013
RoHS Verified

Serial No.

UL, TUV Mark

LGD Logo

US PATENT No. MADE IN KOREA

Origin

www.jxlcd.com
www.jxlcd.com

Ver 1.0 33/36

 LC216EXN

# APPENDIX 3 Product Specification

# APPENDIX- IV

■ Box Label ■ Pallet Label

L C 2 1 6 E XN SCA1 L C 2 1 6 E XN SCA1
9 PCS LOT/MM-DD 108 PCS LOT/MM-DD

MADE IN KOREA RoHS Verified MADE IN KOREA RoHS Verified

L5EDD5Q00013 L5EDD5Q00013

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

www.jxlcd.com
www.jxlcd.com

Ver 1.0 34/36

 LC216EXN
Product Specification
# APPENDIX- V

Option Pin Circuit Block Diagram

Circuit Block Diagram of LVDS Format Selection pin

VCC

Open

Selector (Pin 21) Selector

1KΩ
66KΩ

ASIC
(TCON)

System Side LCM Side

www.jxlcd.com
www.jxlcd.com
Circuit Block Diagram of Reserved Selection pin
VCC

Open

Selector (Pin 2) Selector

1KΩ

66KΩ

ASIC
(TCON)

System Side LCM Side

Ver 1.0 35/36

 LC216EXN
Product Specification
# APPENDIX- VI

LVDS Data-Mapping info. (8bit)

■ LVDS Select : “H” Data-Mapping (JEIDA format)

RCLKP

RCLKM

RAP R13’ R12’ G12 R17 R16 R15 R14 R13 R12 G12”

RBP G14’ G13’ B13 B12 G17 G16 G15 G14 G13 B13”

RCP B15’ B14’ DE VSYNC HSYNC B17 B16 B15 B14 DE”

RDP R11’ R10’ X B11 B10 G11 G10 R11 R10 X”

www.jxlcd.com
www.jxlcd.com
■ LVDS Select : “L” Data-Mapping (VESA format)

RCLKP

RCLKM

RAP R11’ R10’ G10 R15 R14 R13 R12 R11 R10 G10”

RBP G12’ G11’ B11 B10 G15 G14 G13 G12 G11 B15”

RCP B13’ B12’ DE VSYNC HSYNC B15 B14 B13 B12 DE”

RDP R17’ R16’ X B17 B16 G17 G16 R17 R16 X”

Ver 1.0 36/36