Volvo J1939 J1708 Datalink Fault Tracing

Service Bulletin
Volvo Trucks North America, Inc.

Greensboro, NC USA Trucks
Date Group No. Page
This Service Bulletin replaces Service Bulletin 371–44,
“Data Links, Fault Tracing” (11.2002), publication number
12.2004 371 44 1(25)
PV776–TSP177224.
Data links, fault tracing
VN, VHD VERSION2
From build date 11.2002
Data Links, Fault Tracing
T3015830
Contents
“Data Links, Fault Tracing” page 3
“Terminating Resistor, Checking” page 13
“J1708 Information Link, Fault Tracing” page 14
“J1939 Control Link, Fault Tracing” page 16
PV776-20 020644 USA16430

Volvo Trucks North America, Inc. Date Group No. Page
Service Bulletin 12.2004 371 44 2(25)
Tools
Special Tools
9990008 J-38125-8 J-39200

Set of Test Pins Wire Crimpers Digital Multimeter (DMM)
9998699 9990062 J-42449

Breakout Box 62 Pin Cable Extension JAE Terminal Probes
Troubleshooting
Data Links, Fault Tracing
General Troubleshooting Procedures
The control units share information via two different data links “information link SAE
J1587/1708” and “control link SAE J1939”
The messages on the SAE J1587/1708 information link are for example, fault codes and
warning messages. In some cases the SAE J1587/1708 link also acts as a reserve for
SAE J1939. VCADS Pro only communicates on SAE J1587/1708.
SAE J1939 is a faster link which means more data can be transmitted. SAE J1939
is used to transmit data that the system uses for control functions, for example,
engine speed (rpm).
Checks:
• “J1708 Information Link, Fault Tracing” page 14
• “J1939 Control Link, Fault Tracing” page 16
• Use Multimeter J-39200 (or equivalent tool) to perform

tests.
• When troubleshooting wiring and connectors use

breakout boxes/harnesses when available. A list
of various breakout boxes/harnesses is included in
“Special Tools” page 2.
• Never pierce the wiring insulation with test probes.
• Do not pierce through seals on water-resistant

connectors.
• Never insert test probes into connectors. The probes

may spread the terminals and cause intermittent faults.
• If breakout boxes/harnesses are not available, contact

the metal outer edges of connector terminals as
necessary to take readings.
• Consult “VN or VHD Series Electrical Schematics” in

Group 37 for vehicle specific wiring and connector
information. These schematics include pin-out and
vehicle location drawings for connectors.
Visual Inspection
Before beginning electrical checks, visually inspect the
wiring and connectors.
• Inspect for corrosion in wiring or connectors.
• Check that terminal pins are not bent or damaged, and

are locked into their connectors and properly crimped.
• Check that the terminal pins make good mechanical

contact with their mating pin.
• To help locate intermittent faults, wiggle the wire and

connector while testing.
Wiring and Connectors

Troubleshooting data link wiring is no different than
troubleshooting any other wiring. A DMM is used to take
measurements for resistance or voltage at various points
in the circuit. Based on those readings and working with
wiring schematics, the technician can narrow the search
area until the exact cause of a wiring failure is determined.
For general information about how to troubleshoot the

wiring and connectors see "Troubleshooting Wiring and
Connectors" found in the "Electrical General, VN and
VHD" manual in group 30.
Data links
W3005654
Note: Not all modules will be present MID 144 Vehicle ECU J1939–1 Main network SAE
in every vehicle. MID 146 Climate control ECU J1939
MID 206 Radio J1939–3 Section of SAE J1939
MID 128 Engine ECU MID 216 Lighting Control under the instrument
MID 136 Anti-lock Brake (ABS) Module cluster
ECU MID 232 Airbag, control unit J1939–4 Section of SAE J1939
MID 140 Instrument Cluster MID 249 Body builder module under the bodybuilder
MID 142 Satellite MID 250 Steering Wheel control unit
Communications Module
SAE J1587/1708
For checking see “J1708 Information Link, Fault Tracing” page 14.
SAE J1587/1708 is used for, amongst other things, transmitting fault code information.
Faults which can affect the entire SAE J1587/1708 datalink can create problems when
fault tracing, since it can be difficult to communicate with the source in order to carry out
tests using VCADS pro. A simple way of checking if VCADS pro is in contact with all
control units on the SAE J1587/1708 link is “17034-2 Vehicle information, test”. An
indication that there is a problem with SAE J1587/1708 can be that fault codes from a
certain control unit can not be corrected.
There are various types of errors that store fault codes for the SAE J1587/1708 link
(SID 250). If a control unit is able to store a fault code then the fault more than likely is
associated with faulty wiring, connectors or sensors. The fault could be an open-circuit
or short-circuit in the cable harness in one or more places. In order to determine an
open-circuit in the cable harness, check the voltage levels at each control unit. See
“J1708 Information Link, Fault Tracing” page 14.
Fault codes in the SAE J1587/1708 link (SID 250) can also be caused by another control
unit not transmitting information. The reason for this can be due to faults in components
connected to the other control unit. Therefore, all other fault codes must be corrected
before starting the datalink fault tracing process.
List of MID numbers

Note: Not all MIDs will be present on every vehicle.
MID 128 Engine ECU

MID 130 Transmission control unit
MID 136 Anti-lock Brake (ABS) ECU
MID 140 Instrument Cluster
MID 142 Satellite Communications
MID 144 Vehicle ECU
MID 146 Climate control ECU
MID 172 Test tool, ie. VCADS PRO
MID 206 Radio
MID 216 Lighting Control Module
MID 219 VORAD/ACC
MID 232 Airbag, control unit
MID 249 Body builder module (BBM)
MID 250 Steering Wheel Module
SAE J1939
For checking see “J1939 Control Link, Fault Tracing” page 16.
The information on the SAE J1939 control link is used for control functions. Therefore,
the diagnostics for SAE J1939 have been developed and supplemented with more fault
codes for a more precise reading. The fault codes that are transmitted on the SAE
J1587/1708 link are also transmitted, in the event of more serious faults, on the SAE
J1939 link.
If control unit A is missing the message from another control unit B, the fault codes
PSID 200 - 214 are used to determine from which control unit the message is missing.
If control unit B loses contact with the link, other control units can store fault codes
indicating control unit B has lost communications.
Example:
If there is an open - circuit on the SAE J1939 link at the vehicle ECU (MID 144), PC
connector, the message from the vehicle ECU does not reach the other control units on
SAE J1939. The instrument cluster and ABS ECU use the messages from the vehicle
ECU. The instrument cluster and ABS ECU store fault codes when the message is not
received. The instrument cluster stores fault codes “MID 140 PSID 201 FMI 9” and the
ABS ECU stores “MID 136 PSID 201 FMI 9”.
PSID 201 is stored by both the instrument cluster and ABS ECU which indicates that the
vehicle control has an interruption in the SAE J-1939 data link. This can be useful in
order to find faults on the data link. If there is a fault in the cable harness the fact that
there is still contact between certain control units can be used to eliminate sections
of the cable harness. In the event of certain errors in the SAE J1939 link the fault
codes are stored as a SID 231 message.
Note: It is important to remember which control units the vehicle is equipped with and
which fault codes are stored in each control unit.
Explanation of PSID 200-214

Note: Not all control units will be present on every vehicle.
PSID 200 Open-circuit, bad data, data link, engine

control unit (MID 128)
PSID 201 Open-circuit, bad data, data link, vehicle
ECU (MID 144)
PSID 202 Open-circuit, data link, instrument
cluster (MID 140)
PSID 204 Open-circuit, data link, ABS ECU (MID
136)
PSID 210 Open-circuit, data link, Lighting Control
Module(LCM) (MID 216)
PSID 214 Open-circuit, data link, body builder
module (MID 249)
Data Link Construction
W3005333
1 Data link backbone 5 Chassis harness — engine harness in-line connector
2 Terminating resistors 6 Chassis harness — cab harness bulkhead pass-through
3 Stub connections for ECUs connector
4 Diagnostic connector
The J1939 Control Data Link consists of a backbone (1), terminating resistors (2) at each
end, and stubs spliced out (3) for each ECU on the data link. On vehicles with Volvo
engines, the terminating resistor at the engine end is located inside the Engine ECU.
The J1939 Control Data Link complies with SAE standards and consists of 2 twisted
wires:
• Wire 406 is yellow in color and carries the Controller Area Network high (CAN_H)
digital signal of approximately 2–5 volts.
• Wire 407 is green in color and carries the Controller Area Network low (CAN_L)
digital signal of approximately 0–3 volts.
Diagnostic Connector
W3005648
9–pin Diagnostic Connector

Cavity
Circuit Description
Position
A 0Z (B-)
B 402 (B+)
C 406C (CAN_H, yellow)
D 407C (CAN_L, green)
E not connected
F 400G (SAE A, 1708)
G 401G (SAE B, 1708)
H not connected
J 196DR (Ignition)
Note: The J1939 Data Link can be accessed at the 9–pin
diagnostic connector.
SID 231 J1939 Data Link Fault
W3005017
The following table lists Failure Mode Identifiers (FMI) that may be helpful in identifying
data link problems. Please note the following when troubleshooting data link failures
by fault codes.
• The type of FMI that an individual ECU can monitor is dependent on the software in
the ECU. All FMIs cannot be recognized by all ECUs.
• The ECU reporting the fault may not be the ECU that is involved at the site of the
specific failure. For example, The Engine ECU may report a data link fault that is
actually at the VECU. The VECU would not be able to report if the data link is broken
between the VECU and data link backbone.
FMI Description Note

0 Data valid, but high
1 Date valid, but low
2 Data erratic A
3 Voltage shorted high
4 Voltage shorted low
5 Current low or open C
6 Current high or short C
7 Mech syst no response
8 Abnormal freq or PW
9 Abnormal update rate B
10 Abnormal change rate
11 Failure unknown C
12 Loss of intelligent device D
13 Out of calibration
14 Special instruction
A. FMI 2, Data Erratic is given when the ECU does not see any J1939 messages
and is not able to communicate on the J1939 network. This is typically a result
of a problem in the wiring, i.e., shorted high or low, or the ECU may be totally
disconnected from the J1939 data link. When an ECU detects this situation, it
should set the fault code FMI 2. Other ECUs will also set other fault codes for loss
of messages from this ECU.
B. FMI 9, Abnormal Update Rate is given when an ECU is seeing messages from
a specific ECU on the J1939 network, but needed data is not present. This is
typically where the J1939 data link is functioning, and the ECU is communicating, but
having a local problem with a sensor.
C. FMI 11, Failure Unknown indicates an internal problem in the ECU.
D. FMI 12, Loss of Intelligent Device is given when an ECU is expecting to receive
messages from another ECU on the network, and the messages are not present. For
example, the Engine ECU expects certain messages from the ABS system; FMI 12 is
logged if those messages are not there. This fault is probably caused by a physical
break (open circuit) in the J1939 wiring, somewhere between the ECUs, or when an
ECU is off-line due to a blown fuse or bad component.
Note that the device that logs this fault is NOT the faulty ECU – it has instead
detected the fault.
J1939 Data Link Voltage Check

The J1939 Control Data Link operates at the following voltages:
Data Link Wires Key Measuring Point Expected Value

Position
Wire 406 (CAN_H, yellow) On Pins for Wire 406 (yellow) - Ground Fluctuating
between 2 - 5
Volts
Wire 407 (CAN_L, green) On Pins for Wire 407 (green) - Ground Fluctuating
between 0 - 3
Volts
Between Wire 406 and Wire 407 On Pins for Wire 406 (yellow) - Pins for Wire Fluctuating
407 (green) between 0 - 5
Volts
It is expected that the voltages quoted in the table above exist on Wire 406 (CAN_H,
yellow) and Wire 407 (CAN_L, green) at any point on the data link. Due to the fact that
multiple ECUs are both "talking" and "listening" any time the ignition key is on, the
voltage reading will have limited troubleshooting value.
J1939 Data Link Resistance Check

When operating properly, the J1939 Control Data Link has a resistance of approximately
60 between Wire 406 (CAN_H, yellow) and Wire 407 (CAN_L, green) at any point on
the data link. Checks can be made at the diagnostic connector, terminating resistors, or
any ECU on the J1939 Control Data Link.
Use a DMM to check the resistance at suspected fault locations observing the following
points:
• For detailed, vehicle specific schematics see "VN/VHD Electrical Schematics"
found in group 37.
• Breakout boxes for some components may exist to aid in troubleshooting. See
"Tools" for more information.
• Back probe connectors when possible to avoid pin or socket damage.
• Terminating resistors must remain in the circuit for test.
Function Key Measuring Point Expected Value If Expected Value Not Correct Check:
Position
Grounded Circuit Off Pins for Wire 406 OL (Infinite Grounded Circuit
Check (yellow) - Ground Resistance)
Grounded Circuit Off Pins for Wire 407 OL (Infinite Grounded Circuit
Check (green) - Ground Resistance)
J1939 Data Link Off Pins for Wire 406 60 1. Check terminating resistors. See
Resistance Check (yellow) - Wire 407 “Terminating Resistor, Checking” page
(green) 13.
2. Wiring/connector fault in backbone
or stubs. See “Wiring and Connectors”
page 4 and “J1939 Data Link
Troubleshooting Example” page 18.
Terminating Resistor, Checking
W3005518
Terminating Resistor, 2–pin
Terminating resistors are wired to each end of the J1939 data link to prevent signal
reflections. They must remain connected for the data link to function properly. The
resistance value of each terminating resistor is 120 . When properly installed in the
data link, their combined resistance is 60 since they are connected in parallel.
The terminating resistor at one end of the J1939 data link is located in the Fuse/Relay
Center near the VECU and the other near the engine ECU. On vehicles equipped
Volvo engines, the terminating resistor at the engine end is located inside the EECU.
On vehicles equipped with Cummins engine, the terminating resistor is located in the
harness area just outside of the Engine ECU.
A J1939 stub connection is located at the transmission area in the chassis harness.
On vehicles equipped with an electronically controlled transmission (Allison/Autoshift
II/Meritor Freedom Line), the connection to the transmission is located at the chassis
harness. On vehicles equipped with a manual non-electronically controlled transmission
- the connector stub will have an unterminated blanking plug installed.
Only two terminating resistors are used in a vehicle. Never install three in one truck.
If more than two terminating resistors exist in the J1939 circuit, damage to the ECU
electronics can occur over time. You can easily check to see if you have two resistors by
measuring the resistance between circuits 406 and 407, at the diagnostic connector,
with the ignition OFF. The correct resistance is 60 .
If by chance a vehicle has more terminating resistors installed in the link than required,
the resistance value between circuit 406 and 407 will be approx. 40 ohms. This would
give an indication to go and check the locations mentioned above and remove the plugs
one at a time until the correct resistance reading is obtained. You should then find that
you have more than one installed. To fix the problem order a blanking plug and install in
the appropriate location, depending on vehicle transmission type.
To check the terminating resistors, the J1939 data link can be accessed at the 9 pin
diagnostic connector.
Use a DMM to check the following:
9-pin Diagnostic Connector

Function Key Position Measuring Point Expected Note If Expected Value not met,
Value check
Terminating Off Pin D - Pin C 60 1. If 120 , one terminating
Resistor Check resistor missing or wiring fault.
2. If >1k , both terminating
resistor missing or wiring fault.
3. If OL (infinite), open circuit.
4. If <1 , short circuit in data link
wires.
3711-21-03-01
J1708 Information Link, Fault Tracing
Other special equipment: J-39200
NOTE!
• During fault-tracing check the relevant connectors.
Check for loose connections, contact resistance
and oxidation. For a more detailed description of
fault-tracing cables and connectors, see separate
service information under group 37.
• Do not use the chassis as a ground when taking

readings. Use the ground plate in the distribution box.
• For measurement points and adapters see “Signal

Indication” for the relevant system.
Additional information
When checking the data link measurement and the
values are outside of the given ranges, there are several
possible explanations.
1
If the voltage is approx. greater than 5 V DC the data
link is possibly shorted to a higher voltage and must be
inspected to find the cause.
A wire of higher voltage could be cross connected
to the data link via chaffing or pin misalignment at
connectors or control units, etc.
A second, but least likely, possibility is that the internal
databus of an ecu has failed in some way causing
an interruption of messaging on the link. If this is
suspected, disconnect the suspect ecu temporarily or
either connect a spare ecu to check if the problem
goes away.
2
If the voltage is aprrox. less than 2 V DC the datalink
is possibly shorted to ground and must be inspected
to find the cause.
A wire of lower voltage or ground type could be
cross connected to the data link via chaffing or pin
misalignment at connectors or control units, etc.
Either one or both of the data link wires are shorted

to ground via a rub through (chaff). Inspect the
entire data link for possible signs of abrasion. Repair
according to guidelines outlined in this manual.
A third, but least likely, possibility is that the internal

databus of an ecu has failed in some way causing
an interruption of messaging on the link. If this is
suspected, disconnect the suspect ecu temporarily or
connect a spare ecu to check if the problem goes away.
Checking sub-systems
1
Conditions:
• Measurement box with adapter connected between

the relevant control unit and cable harness.
• Measuring voltage using the multimeter with the MIN /

MAX-function engaged.
• Control unit connected.
• The ignition key in the drive position.
Measuring points Desired value

SAE J1587/1708 A - V ≈ 0 - 5 V DC 1
ground Vmax ≈ 5 V DC
Vmin ≈ 0 V DC
SAE J1587/1708 B - V ≈ 0 - 5 V DC 1
ground Vmax ≈ 5 V DC
Vmin ≈ 0 V DC
SAE J1587/1708 A - V ≈ 2 - 5 V DC
SAE J1587/1708 B
1
The voltage must vary within the interval.
Note: The voltage on the information link varies and

is dependent on the number of control units and traffic
on the information link.
J-39200
3711-21-03-02
J1939 Control Link, Fault Tracing
You must read and understand the precautions and
guidelines in Service Information, group 30, "General
Safety Practices", before performing this procedure.
If you are not properly trained and certified in this
procedure, ask your supervisor for training before
you perform it.
Other special equipment: J-39200

NOTE!
• During fault-tracing check the relevant connectors.
Check for loose connections, contact resistance
and oxidation. For a more detailed description of
fault-tracing cables and connectors, see separate
service information under group 37.
• Do not use the chassis as a ground when taking

readings. Use the ground plate in the distribution box.
• For measurement points and adapters see “Signal

Indication” for the relevant system.
Checking sub-systems
1
Conditions:

• Measuring voltage using multi meter J-39200 with

the MIN MAX-function connected.
• Ignition key in the drive position.

Note: The voltage of the control link varies and depends
on the number of control units and the traffic on the
control link.

SAE J1939A - ground V ≈ 2 - 5 V DC
SAE J1939B - ground V ≈ 0 - 3 V DC
SAE J1939A - SAE V ≈ 0 - 1 V DC
J1939B
J-39200
2
Conditions:

• Measuring resistance using a multimeter.
• Ignition key in stop position.

SAE J1939A - SAE R = 50 - 70
J1939B
Two terminations
SAE J1939A - SAE R = 100 - 140
J1939B
One termination
Comments:
When the resistance R ≈ 60 the cable harness is

probably fault free from the particular connector to
two terminating resistors.
If the resistance R ≈ 120 from the relevant connector

then measuring is only conducted to the terminating
resistor.
J-39200
J1939 Data Link Troubleshooting Example
W3005333
1 Data en-
link gine
back- har-
bone ness
2 Terminating in-line
re- con-
sis- nec-
tors tor
3 Stub 6 Chassis
con- har-
nec- ness
tions —
for cab
ECUs har-
4 Diagnostic ness
con- bulk-
nec- head
tor pass-
5 Chassis through
har- con-
ness nec-
— tor
Note: This example is intended as a guide for the

logic used to troubleshoot a data link wiring problem.
The illustration should be used to help clarify the
troubleshooting example. Always refer to vehicle-specific
wiring schematics found in Group 37 when performing
vehicle troubleshooting.
1
Begin by visually verifying that the two terminating
resistors are in place:
1a. One at the engine ecu. Vehicle equipped with
the Volvo engine, the terminating resistor is built into
the EECU and is not visible. Vehicles with Cummins
engines the terminating resistor is located on the
engine harness.
1b. One inside the cab, forward of the fuse/relay panel

(visible when the fuse/relay cover is removed).
2
Using an ohmmeter with the ignition key switch in the
OFF position, check the resistance between circuits 406
(CAN_H, J1939A, yellow) and 407 (CAN_L, J1939B,
green) at the diagnostic connector.
2a. If 60 (±10 ) resistance is measured, it is likely
that the backbone circuit is intact, since the 60
represents the two 120 terminating resistors in
parallel. If trouble is still present, it is most likely in
one of the ECU stub circuits or at the ECU terminal
themselves. Go to Step 6.
2b. If approximately 120 resistance is measured,

this indicates that one of the terminating resistors is
missing, poorly connected or else there is an open
circuit in the backbone at some point. Use the fault
codes (if present) to narrow down the likely location
based on which ECU’s are complaining about missing
data from other ECU’s. Go to Step 3.
2c. If approximately 40 resistance is measured,

there are more than 2 terminating resistors installed.
To fix the problem order a blanking plug and install
in the appropriate location, depending on vehicle
transmission type.
3
Disconnect the Cab-chassis/pass-through connector
(item 6) at the bulkhead and re-test the resistance of
circuit 406–407 at the diagnostic connector.
3a. If the resistance is the same as that measured in
Step 2b, then that means the trouble is likely on the
chassis side of the cab-chassis pass-through, since
the 120 being measured must be teminating resistor
located in the cab. Go to Step 4.
3b. If the resistance is greater than what was

measured in Step 2b, then the trouble is likely on the
cab side of the harness, since the different reading
means you can no longer ’see’ the engine side
terminating resistor. Go to Step 5.
4
With the pass-through (item 6) still disconnected, check
the resistance between circuit 406–407 on the chassis
harness side of the pass-through, ’looking’ towards the
engine (120 should be present). While shaking/moving
the harnesses to look for an intermittent connection,
check the following items:
• Check for continuity between all circuit 406 points

— pass-though, EECU, terminating resistor, and
transmission (if automated/automatic transmission)
• Check for continuity between all circuit 407 points

— pass-though, EECU, terminating resistor, and
transmission (if automated/automatic transmission)
The 406 and 407 backbone circuits can, also, be
disconnected at the engine-to-chassis harness in-line
connector (item 5 — located near the starter relay
breakout, near the bulkhead) to further isolate whether the
problem exists on the ’engine’ side or the ’chassis’ side.
5
With the pass-through (item 6) still disconnected, check
the resistance between circuit 406–407 on the cab side of
the pass-through, ’looking’ into the cab (120 should be
present). While shaking/moving the harnesses to look for
an intermittent connection, check the following items:
• Check for continuity between all circuit 406 points.
• Check for continuity between all circuit 407 points.
6
Check for continuity between circuit 406 at the diagnostic
connector and all circuit 406 point at the ECU’s and
terminating resistors. All circuit 406 should have
continuity to all other ECU’s. Perform the same tests
for all circuit 407 points.
If continuity is not found at all points, the trouble
is most likely in the stub to that ECU, or the ECU
connector/terminal itself.
Service Procedures
3711-16-02-02
J1939 Data Link Wiring (Unshielded), Repair
you perform it.
Note: This procedure complies with TMC RP142

“High-Speed Data Link Repair Guidelines.”
Note: Stagger wire cuts and splices to minimize bulges in

data link cable.
W3004993
1 Cable bundle, existing
2 Cable bundle, new
3 Heat-shrinkable connector
1
Make certain the vehicles ignition is OFF before
beginning this procedure.
2
Remove the data link from the wiring harness as
necessary and cut out the damaged section of cable.
Note: The replacement section of cable (P/N 982689)
must be somewhat longer than the original to allow for
staggering of the splices.
3
Strip approximately 50 mm (2 in.) of cable jacket and
shield at each end of the splices to expose the wiring.
Use caution not to cut the wire insulation.
4
Slide a piece of heat-shrink tubing over each end of the
cut cable bundle to seal the data link after the wires have
been spliced. The tubing should be approximately 50 mm
(2 in.) longer than the repair area.
W3004994
2 Cable bundle, new
3 Heat-shrink tubing
5
Stagger cut the wiring to minimize bulges in the data
link cable. Strip approximately 6.3 mm (0.25 in.) of
wiring insulation at each wire end. Use caution not
to cut the wire strands.
W3004995
2 Cable bundle, new
6
Observe polarity when connecting the 406 (CAN-H,
yellow) and 407 (CAN-L, green) wires. Use a heat
shrinkable wiring connector to splice the wires together.
Insert each end of the wire into the connector until it
hits the wire stop.
W3004996
1 Wire stop
7
Insert the connector into the proper anvil on the crimping
tool and crimp. Gently tug on the spliced connection to be
sure the wire is secure.
W3004997
8
Use a heat gun to activate the heat shrink. Look for
sealant at each end of the connector as evidence of a
good application. Note: Do not use an open flame to
apply heat shrink.
W3004889
1 Visible sealant
9
Center the piece of heat shrinkable tubing installed in
step 5 over the entire splice area. There should be
approximately 25 mm (1 in.) overlap at each end of the
splice area. Starting at the center, use a heat gun to
shrink the tubing. Look for sealant at each end of the
W3004883 connector as evidence of a good application. Note: Do
1 Cable bundle, existing not use an open flame to apply heat shrink.
2 Cable bundle, new
3 Heat shrink tubing
4 Visible sealant
10
After both ends of the cable are spliced, install the data
link back into the wiring harness and secure as necessary.
Wire Splice, Solder and Seal

you perform it.
W3000568
Fig. 1: Wire splicing

1 Solder
2 Soldering iron
3 Heat shrink tubing with sealant
4 Wires twisted
Soldering Procedure
1
Clean and tin the soldering iron tip.
2
Clean the terminal to be soldered.
3
Strip the wire as necessary to fit the terminal. Do not cut
or nick the wire when stripping. Note: The replacement
section of cable (P/N 982689) must be somewhat longer
than the original to allow for staggering of the splices.
W3000569
1 Strip as necessary
2 Wire
4
Slide a piece of sealant shrink tubing onto the wire.
5
Insert the wire in the terminal and, with a pair of crimpers
(as recommended by the connector manufacturer),
squeeze the small tabs onto the wire insulation. Not all
types of terminals have these tabs. Be certain to use the
crimpers recommended by the connector manufacturer.
With a blunt instrument, form the bare wire so that it will
lay against the soldering area of the terminal.
6
Using the soldering iron, apply heat to the outside of the
terminal while holding the solder on the wire on the inside
of the terminal. When a sufficient amount of heat has
been transferred from the gun through the terminal and
into the wire, the solder will be melted by the wire. Melt a
sufficient amount of solder on the wire and withdraw
the solder and the tip of the iron.
NOTE: Do not hold the terminal with pliers or anything

metal during the solder operation, as heat will be
W3000571 conducted away from the terminal.
1 Solder
2 Tabs (crimp over wire insulation)
3 Wire
4 Soldering iron
5 Terminal
7
Slide the sealant shrink tubing over the soldered
connection, making sure all exposed wire is covered.
Heat the tubing with a heat gun to shrink. Shrink until the
tubing is tight around the wire and the sealant is visible
out of both ends of the tubing.

Volvo J1939 J1708 Datalink Fault Tracing

Uploaded by

Copyright:

Available Formats

Volvo J1939 J1708 Datalink Fault Tracing

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Volvo J1939 J1708 Datalink Fault Tracing

Uploaded by

Copyright:

Available Formats

Service Bulletin

Volvo Trucks North America, Inc.

Data Links, Fault Tracing

“Terminating Resistor, Checking” page 13

“J1708 Information Link, Fault Tracing” page 14

“J1939 Control Link, Fault Tracing” page 16

PV776-20 020644 USA16430

9990008 J-38125-8 J-39200

9998699 9990062 J-42449

• “J1708 Information Link, Fault Tracing” page 14

• “J1939 Control Link, Fault Tracing” page 16

• Use Multimeter J-39200 (or equivalent tool) to perform

• When troubleshooting wiring and connectors use

• Never pierce the wiring insulation with test probes.

• Do not pierce through seals on water-resistant

• Never insert test probes into connectors. The probes

• If breakout boxes/harnesses are not available, contact

• Consult “VN or VHD Series Electrical Schematics” in

• Inspect for corrosion in wiring or connectors.

• Check that terminal pins are not bent or damaged, and

• Check that the terminal pins make good mechanical

• To help locate intermittent faults, wiggle the wire and

Wiring and Connectors

For general information about how to troubleshoot the

List of MID numbers

MID 128 Engine ECU

Explanation of PSID 200-214

PSID 200 Open-circuit, bad data, data link, engine

Data Link Construction

9–pin Diagnostic Connector

SID 231 J1939 Data Link Fault

FMI Description Note

C. FMI 11, Failure Unknown indicates an internal problem in the ECU.

J1939 Data Link Voltage Check

Data Link Wires Key Measuring Point Expected Value

J1939 Data Link Resistance Check

• Back probe connectors when possible to avoid pin or socket damage.

• Terminating resistors must remain in the circuit for test.

Terminating Resistor, Checking

Terminating Resistor, 2–pin

Use a DMM to check the following:

9-pin Diagnostic Connector

• Do not use the chassis as a ground when taking

• For measurement points and adapters see “Signal

Either one or both of the data link wires are shorted

A third, but least likely, possibility is that the internal

• Measurement box with adapter connected between

• Measuring voltage using the multimeter with the MIN /

• Control unit connected.

• The ignition key in the drive position.

Measuring points Desired value

Note: The voltage on the information link varies and

Other special equipment: J-39200

• Do not use the chassis as a ground when taking

• For measurement points and adapters see “Signal

• Measurement box with adapter connected between

• Control unit connected.

• Measuring voltage using multi meter J-39200 with

• Ignition key in the drive position.