DESIGN OF CIRCULAR WATER TANK (Rigid joint)

Nameof work:- Narok ETP

1 Tank capacity 400 K ltr 400000 ltr

2 Depth of water 4.00 mtr 4000 mm

3 Free board 0.20 m 200 mm

4 Concrete M 25 unit weight 24000 N/m3

scbc 7 N/mm2 m 13.3

5 Steel fy 460 Tensile stress 115 N/mm2

6 Nominal Cover 35 mm Effective Cover 40 mm

7 Reinforcement
Vertical 12 mm F 125 mm c/c
Hoops Ring
upto 25% height 12 mm F 170 mm c/c

upto 50% height 12 mm F 200 mm c/c

upto 75% height 12 mm F 220 mm c/c

upto 100% height 12 mm F 440 mm c/c

Floor (both direction) 10 mm F 200 mm c/c

170 11600 170

12 mm f Ring 100%
440 mm c/c 1.00 m

12 mm f Bars
250 mm c/c
75%
12 mm f Ring 1.00 m
220 mm c/c

4000

12 mm f Ring 50%
200 mm c/c 0.60 m

12 mm f Bars
125 mm c/c 10 mm f Ring
200 mm c/c
12 mm f Ring 1.40 m 10 mm f Ring
170 mm c/c 200 mm c/c

170

75
 DESIGN OF CIRCULAR WATER TANK (Rigid joint)
Nameof work:- Narok ETP
Tank capacity 400 K ltr 400000 mm
Depth of water 4.00 m 4000 mm
Free board 0.20 m 200 mm
Concrete M 25
Steel fy 460 N/mm2 Tensile stess = 115 N/mm2
scbc 7 N/mm2 m = 13.3
Nominal cover 35 mm Effective cover = 40 mm

### Design Constants:- For HYSD Bars Cocrete M = 25

sst = 115 N/mm2 wt. of concrete = 25000 N/mm2

scbc = 7 N/mm2 m = 13.3
m*c 13.3 x 7
k= = = 0.447
m*c+sst 13.3 x 7 + 115
j=1-k/3 = 1 - 0.447 / 3 = 0.851
R=1/2xc x j x k = 0.5 x 7 x 0.851 x 0.447 = 1.332

### Dimention of tank:- Effective depth of tank = 4.00 - 0.20 = 3.80

ÕxD 2 400000 x 1000
If D is the inside diameter of tank, we have = x 3.80 =
4 1000 x 1000

Ö
400 x 4
\ from which D = 11.57 m say = 11.60 m
3.143 x 3.80
Provide a diameter of = 11.60 m

### Determination of bending moment and hoop tension:-

Thickness of wall from empirical formula = 3H+5 = 3 x 4.00 + 5 = 17 cm 170

H2 = 4.00 x 4.00
= 8 h = H/3 = 4.00 / 3 = 1.333
DT 11.60 x 0.17
The height above base, upto which cantilever action will be there is given by H/3 or 1 m which ever is heigher
D
Maximum ring tension at this level, per meter height = w (H-h) where w = 9800 N/m2
2
11.60
pressure at h/3 = 9800 x ( 4.00 - 1.333 )x = 151573 N
2
Maximum prerssure at bottom = wH = 9800 x 4.00 = 39200 N
1 1.333
\ maximum cantilever B.M. = Mf = x ### x 1.333 x = 11615 N-m/m
2 3

### Design of setion for cantilever action:-

if d is the effective thickness of tank wall,

Ö Ö
Mf 11615 x 1000
D= = = 93.00 mm
1000 R 1000 x 1.33
\ Total thickness =d +cover = 93 + 35 = 128 = say 130 mm
However, provide a minimum thickness equal to the greater of following;
(I) 150mm (II) 30H+ 50 = 30 x 4.00 + 50 = 170 Hence provide T= 170
Providing 35 mm cover to the center of reinforcement, availble d = 135 mm
Mf 11615 x 1000
Ast =
sst . J .d =
Area of steel for cantilever bending is given by= = 879
115 x 0.851 x 135
3.14xdia2 3.14 x 12 x 12
using ### mm bars A = = = 113
4 x100 4 x 100
Spacing of hoop Bars = 1000 x 113 / 879 = 129 say = 120 mm
Hence Provided 12 mm F bar, @ 120 mm c/c upto height of 1.40 m from base
 Above this height, curtail half bars and continue the other half upto top. Let us test this for devlopment length
[email protected]
f .sst 12 x 115
Ld = = 431 mm say 0.43 m
4. tbd 4 x 0.8 =
Hence half bars may be curtailed at 1.40 m height above the base. These vertical bars are to be
provided inner face . Keep a clear cover of = 25 mm

### Design of section for hoops action;

Maximum hoops tension 151573 N at 1.33 m above the base
\ area of ring, Ash = 151573 / 115 = 1318 mm 2

Let us provide rings atboth faseHence of area of ring in each face= 659 mm2
3.14xdia2 3.14 x 12 x 12
using ### mm bars A = = = 113
4 x100 4 x 100
Spacing of hoop Bars = 1000 x 113 / 659 = 172 say = 170 mm
Hence Provided ### mm F bar, @ 170 mm c/c upto height of 1.40 m from base
and above this, the spacing may be increased
1000 x 113
Actual , Ast = 2 x = 1330 mm2
170
151573
\ sct =
170 +( 13.3 - 1 )x 1330 =
0.813 < 1.2
1000 x
Hoop tension at 2.00 m below top = 9800 x 2.00 x 11.60 / 2.00 = 113680
\ area of ring, Ash = 113680 / 115 = 989 mm 2

Let us provide rings atboth faseHence of area of ring in each face= 495 mm2
3.14xdia 2
3.14 x 12 x 12
using ### mm bars A = = = 113
4 x100 4 x 100
Spacing of hoop Bars = 1000 x 113 / 495 = 228 say = 220 mm
Hence Provided ### mm F bar, @ 220 mm c/c upto height of 2.00 m from base
0.3
At the top, minimum Ash = x 1000 x 170 = 510 / 2 = 255 mm2
100
Spacing of hoop Bars = 1000 x 113 / 255 = 443 say = 440 mm c/c

### Distribution reinforcement:-

170 - 100
Percentage area of distribution reinforcement is 0.30 - 0.10 x = 0.280 %
450 - 100
0.280
\ Ash = x 1000 x 170 = 476 area of steel in each face = 238
100
However , no additional reinforcement will be provided at inner face since the vertical steel for cantilever action
will serve this purpose. Hence provided Ast= 238 mm2 in vertical direction at the outer face.
3.14xdia2 3.14 x 8 x 8
using 8 mm bars A = = = 50
4 x100 4 x 100
Spacing of hoop Bars = 1000 x 50 / 238 = 211 say = 200 mm
Hence Provided these 8 mm F bar, @200 mm c/c

### Provision for haunches:-

It is customary to provide150 mmx150mm haunchesat the junction of wall and base.
A haunches reinforcement of 8 mm f @ 200 mm c/c may be provided.

### Design of tank floor.:-

Since the tank floor is resting on ground throughout , provide a minimum thickness of 150
0.30
Minimum Ast = x 150 x 1000 = 450 mm2 in each direction
100
Provide half the reinfocement near each face, Ast = 225 mm2
3.14xdia 2
3.14 x 8 x 8
using 8 mm bars A = = = 50
4 x100 4 x 100
Spacing of hoop Bars = 1000 x 50 / 225 = 223 say = 200 mm
However provide 8 mm f bars @ 200 mm c/c in both direction , at top and bottom of floor slab.
 The floor slab will rest on 75 mm thick layer of lean concrete covered with a layer of tar felt.

### Detail of reinforcement :- The detail shown in drawing.

[email protected]
 m

mm
m
hich ever is heigher

mm

mm2

mm2

m from base
vlopment length

tical bars are to be

ove the base

mm2

N/mm2

mm2

mm2

r cantilever action

mm2

wall and base.

mm
direction

mm2
 DESIGN OF CIRCULAR WATER TANK (Rigid joint)
Nameof work:- Narok ETP

170 11600 170

100%
12 mm f Ring
440 mm c/c 1.00 m

12 mm f Bars
250 mm c/c 75%

12 mm f Ring 1.00 m
220 mm c/c

50% 4000

12 mm f Ring
200 mm c/c 0.60 m

12 mm f Bars
125 mm c/c 10 mm f Ring
200 mm c/c
12 mm f Ring 1.40 m 10 mm f Ring
170 mm c/c 200 mm c/c

150

75
[email protected]
 VALUES OF DESIGN CONSTANTS
Grade of concrete M-15 M-20 M-25 M-30 M-35 M-40 Grade of concrete
Modular Ratio 18.67 13.33 10.98 9.33 8.11 7.18 tbd (N / mm2
scbc N/mm2 5 7 8.5 10 11.5 13
m scbc 93.33 93.33 93.33 93.33 93.33 93.33
kc 0.4 0.4 0.4 0.4 0.4 0.4
(a) sst =
jc 0.867 0.867 0.867 0.867 0.867 0.867
140
N/mm2 Rc 0.867 1.214 1.474 1.734 1.994 2.254 Grade of
(Fe 250) Pc (%) concrete
0.714 1 1.214 1.429 1.643 1.857
kc 0.329 0.329 0.329 0.329 0.329 0.329 M 15
(b) sst = jc 0.89 0.89 0.89 0.89 0.89 0.89 M 20
190 Rc 0.732 1.025 1.244 1.464 1.684 1.903 M 25
N/mm2
Pc (%) 0.433 0.606 0.736 0.866 0.997 1.127 M 30
kc 0.289 0.289 0.289 0.289 0.289 0.289 M 35
(c ) sst =
jc 0.904 0.904 0.904 0.904 0.904 0.904 M 40
230
N/mm2 Rc 0.653 0.914 1.11 1.306 1.502 1.698 M 45
(Fe 415) Pc (%) 0.314 0.44 0.534 0.628 0.722 0.816 M 50
kc 0.253 0.253 0.253 0.253 0.253 0.253
(d) sst =
jc 0.916 0.916 0.916 0.914 0.916 0.916
275
N/mm2 Rc 0.579 0.811 0.985 1.159 1.332 1.506
(Fe 500) Pc (%) 0.23 0.322 0.391 0.46 0.53 0.599

Permissible shear stress Table t v in concrete (IS : 456-2000)

100As Permissible shear stress in concrete tv N/mm2
bd M-15 M-20 M-25 M-30 M-35 M-40
Grade of
< 0.15 0.18 0.18 0.19 0.2 0.2 0.2
concrete
0.25 0.22 0.22 0.23 0.23 0.23 0.23
0.50 0.29 0.30 0.31 0.31 0.31 0.32 M 10
0.75 0.34 0.35 0.36 0.37 0.37 0.38 M 15
1.00 0.37 0.39 0.40 0.41 0.42 0.42 M 20
1.25 0.40 0.42 0.44 0.45 0.45 0.46 M 25
1.50 0.42 0.45 0.46 0.48 0.49 0.49 M 30
1.75 0.44 0.47 0.49 0.50 0.52 0.52 M 35
2.00 0.44 0.49 0.51 0.53 0.54 0.55 M 40
2.25 0.44 0.51 0.53 0.55 0.56 0.57 M 45
2.50 0.44 0.51 0.55 0.57 0.58 0.60 M 50
2.75 0.44 0.51 0.56 0.58 0.60 0.62
3.00 and above 0.44 0.51 0.57 0.6 0.62 0.63

Maximum shear stress tc.max in concrete (IS : 456-2000)

Grade of concrete M-15 M-20 M-25 M-30 M-35 M-40

tc.max 1.6 1.8 1.9 2.2 2.3 2.5
Shear stress tc Reiforcement %
100As 100As
M-20 M-20
bd bd
0.15 0.18 0.18 0.15
0.16 0.18 0.19 0.18
0.17 0.18 0.2 0.21
0.18 0.19 0.21 0.24
0.19 0.19 0.22 0.27
0.2 0.19 0.23 0.3
0.21 0.2 0.24 0.32
0.22 0.2 0.25 0.35
0.23 0.2 0.26 0.38
0.24 0.21 0.27 0.41
0.25 0.21 0.28 0.44
0.26 0.21 0.29 0.47
0.27 0.22 0.30 0.5
0.28 0.22 0.31 0.55
0.29 0.22 0.32 0.6
0.3 0.23 0.33 0.65
0.31 0.23 0.34 0.7
0.32 0.24 0.35 0.75
0.33 0.24 0.36 0.82
0.34 0.24 0.37 0.88
0.35 0.25 0.38 0.94
0.36 0.25 0.39 1.00
0.37 0.25 0.4 1.08
0.38 0.26 0.41 1.16
0.39 0.26 0.42 1.25
0.4 0.26 0.43 1.33
0.41 0.27 0.44 1.41
0.42 0.27 0.45 1.50
0.43 0.27 0.46 1.63
0.44 0.28 0.46 1.64
0.45 0.28 0.47 1.75
0.46 0.28 0.48 1.88
0.47 0.29 0.49 2.00
0.48 0.29 0.50 2.13
0.49 0.29 0.51 2.25
0.5 0.30
0.51 0.30
0.52 0.30
0.53 0.30
0.54 0.30
0.55 0.31
0.56 0.31
0.57 0.31
0.58 0.31
0.59 0.31
 0.6 0.32
0.61 0.32
0.62 0.32
0.63 0.32
0.64 0.32
0.65 0.33
0.66 0.33
0.67 0.33
0.68 0.33
0.69 0.33
0.7 0.34
0.71 0.34
0.72 0.34
0.73 0.34
0.74 0.34
0.75 0.35
0.76 0.35
0.77 0.35
0.78 0.35
0.79 0.35
0.8 0.35
0.81 0.35
0.82 0.36
0.83 0.36
0.84 0.36
0.85 0.36
0.86 0.36
0.87 0.36
0.88 0.37
0.89 0.37
0.9 0.37
0.91 0.37
0.92 0.37
0.93 0.37
0.94 0.38
0.95 0.38
0.96 0.38
0.97 0.38
0.98 0.38
0.99 0.38
1.00 0.39
1.01 0.39
1.02 0.39
1.03 0.39
1.04 0.39
1.05 0.39
1.06 0.39
1.07 0.39
1.08 0.4
1.09 0.4
1.10 0.4
1.11 0.4
1.12 0.4
1.13 0.4
1.14 0.4
1.15 0.4
1.16 0.41
1.17 0.41
1.18 0.41
1.19 0.41
1.20 0.41
1.21 0.41
1.22 0.41
1.23 0.41
1.24 0.41
1.25 0.42
1.26 0.42
1.27 0.42
1.28 0.42
1.29 0.42
1.30 0.42
1.31 0.42
1.32 0.42
1.33 0.43
1.34 0.43
1.35 0.43
1.36 0.43
1.37 0.43
1.38 0.43
1.39 0.43
1.40 0.43
1.41 0.44
1.42 0.44
1.43 0.44
1.44 0.44
1.45 0.44
1.46 0.44
1.47 0.44
1.48 0.44
1.49 0.44
1.50 0.45
1.51 0.45
1.52 0.45
1.53 0.45
1.54 0.45
1.55 0.45
1.56 0.45
1.57 0.45
1.58 0.45
1.59 0.45
1.60 0.45
1.61 0.45
1.62 0.45
1.63 0.46
1.64 0.46
1.65 0.46
1.66 0.46
1.67 0.46
1.68 0.46
1.69 0.46
1.70 0.46
1.71 0.46
1.72 0.46
1.73 0.46
1.74 0.46
1.75 0.47
1.76 0.47
1.77 0.47
1.78 0.47
1.79 0.47
1.80 0.47
1.81 0.47
1.82 0.47
1.83 0.47
1.84 0.47
1.85 0.47
1.86 0.47
1.87 0.47
1.88 0.48
1.89 0.48
1.90 0.48
1.91 0.48
1.92 0.48
1.93 0.48
1.94 0.48
1.95 0.48
1.96 0.48
1.97 0.48
1.98 0.48
1.99 0.48
2.00 0.49
2.01 0.49
2.02 0.49
2.03 0.49
2.04 0.49
2.05 0.49
2.06 0.49
2.07 0.49
2.08 0.49
2.09 0.49
2.10 0.49
2.11 0.49
2.12 0.49
2.13 0.50
2.14 0.50
2.15 0.50
2.16 0.50
2.17 0.50
2.18 0.50
2.19 0.50
2.20 0.50
2.21 0.50
2.22 0.50
2.23 0.50
2.24 0.50
2.25 0.51
2.26 0.51
2.27 0.51
2.28 0.51
2.29 0.51
2.30 0.51
2.31 0.51
2.32 0.51
2.33 0.51
2.34 0.51
2.35 0.51
2.36 0.51
2.37 0.51
2.38 0.51
2.39 0.51
2.40 0.51
2.41 0.51
2.42 0.51
2.43 0.51
2.44 0.51
2.45 0.51
2.46 0.51
2.47 0.51
2.48 0.51
2.49 0.51
2.50 0.51
2.51 0.51
2.52 0.51
2.53 0.51
2.54 0.51
2.55 0.51
2.56 0.51
2.57 0.51
2.58 0.51
2.59 0.51
2.60 0.51
2.61 0.51
2.62 0.51
2.63 0.51
2.64 0.51
2.65 0.51
2.66 0.51
2.67 0.51
2.68 0.51
2.69 0.51
2.70 0.51
2.71 0.51
2.72 0.51
2.73 0.51
2.74 0.51
2.75 0.51
2.76 0.51
2.77 0.51
2.78 0.51
2.79 0.51
2.80 0.51
2.81 0.51
2.82 0.51
2.83 0.51
2.84 0.51
2.85 0.51
2.86 0.51
2.87 0.51
2.88 0.51
2.89 0.51
2.90 0.51
2.91 0.51
2.92 0.51
2.93 0.51
2.94 0.51
2.95 0.51
2.96 0.51
2.97 0.51
2.98 0.51
2.99 0.51
3.00 0.51
3.01 0.51
3.02 0.51
3.03 0.51
3.04 0.51
3.05 0.51
3.06 0.51
3.07 0.51
3.08 0.51
3.09 0.51
3.10 0.51
3.11 0.51
3.12 0.51
3.13 0.51
3.14 0.51
3.15 0.51
 Permissible Bond stress Table t bd in concrete (IS : 456-2000)
M-10 M-15 M-20 M-25 M-30 M-35 M-40 M-45 M-50
-- 0.6 0.8 0.9 1 1.1 1.2 1.3 1.4

Development Length in tension

Plain M.S. Bars H.Y.S.D. Bars

tbd (N / mm2) kd = Ld F tbd (N / mm2) kd = Ld F
0.6 58 0.96 60
0.8 44 1.28 45
0.9 39 1.44 40
1 35 1.6 36
1.1 32 1.76 33
1.2 29 1.92 30
2.0
1.3 27 2.08 28
1.4 25 2.24 26
1.4

Modification factore
1.2

0.8

0.4
Permissible stress in concrete (IS : 456-2000)
Permission stress in compression (N/mm2) Permissible stress in bond (Average) for
Bending acbc Direct (acc) plain bars in tention (N/mm2) 0.0
(N/mm2) Kg/m2 (N/mm2) Kg/m2 (N/mm2) in kg/m2
3.0 300 2.5 250 -- --
5.0 500 4.0 400 0.6 60
7.0 700 5.0 500 0.8 80
8.5 850 6.0 600 0.9 90
10.0 1000 8.0 800 1.0 100
11.5 1150 9.0 900 1.1 110
13.0 1300 10.0 1000 1.2 120
14.5 1450 11.0 1100 1.3 130
16.0 1600 12.0 1200 1.4 140
 0.4 0.8 1.2 1.6 2
Percentage of tension reinforcement
2 2.4 2.8
 VALUES OF DESIGN CONSTANTS
Grade of concrete M-15 M-20 M-25 M-30 M-35 M-40 Grade of concrete
Modular Ratio 18.67 13.33 10.98 9.33 8.11 7.18
scbc N/mm2 5 7 8.5 10 11.5 13
m scbc 93.33 93.33 93.33 93.33 93.33 93.33
kc 0.4 0.4 0.4 0.4 0.4 0.4
(a) sst =
jc 0.867 0.867 0.867 0.867 0.867 0.867
140
N/mm2 Rc 0.867 1.214 1.474 1.734 1.994 2.254
(Fe 250) Pc (%) 0.714 1 1.214 1.429 1.643 1.857
kc 0.329 0.329 0.329 0.329 0.329 0.329
(b) sst = jc 0.89 0.89 0.89 0.89 0.89 0.89
190 Rc 0.732 1.025 1.244 1.464 1.684 1.903
N/mm2
Pc (%) 0.433 0.606 0.736 0.866 0.997 1.127
kc 0.289 0.289 0.289 0.289 0.289 0.289
(c ) sst =
jc 0.904 0.904 0.904 0.904 0.904 0.904
230
N/mm2 Rc 0.653 0.914 1.11 1.306 1.502 1.698
(Fe 415) Pc (%) 0.314 0.44 0.534 0.628 0.722 0.816
kc 0.253 0.253 0.253 0.253 0.253 0.253
(d) sst =
jc 0.916 0.916 0.916 0.914 0.916 0.916
275
N/mm2 Rc 0.579 0.811 0.985 1.159 1.332 1.506
(Fe 500) Pc (%) 0.23 0.322 0.391 0.46 0.53 0.599

Permissible shear stress Table t v in concrete (IS : 456-2000)

100As Permissible shear stress in concrete tv N/mm2
bd M-15 M-20 M-25 M-30 M-35 M-40
< 0.15 0.18 0.18 0.19 0.2 0.2 0.2
0.25 0.22 0.22 0.23 0.23 0.23 0.23
0.50 0.29 0.30 0.31 0.31 0.31 0.32
0.75 0.34 0.35 0.36 0.37 0.37 0.38
1.00 0.37 0.39 0.40 0.41 0.42 0.42
1.25 0.40 0.42 0.44 0.45 0.45 0.46
1.50 0.42 0.45 0.46 0.48 0.49 0.49
1.75 0.44 0.47 0.49 0.50 0.52 0.52
2.00 0.44 0.49 0.51 0.53 0.54 0.55
2.25 0.44 0.51 0.53 0.55 0.56 0.57
2.50 0.44 0.51 0.55 0.57 0.58 0.60
2.75 0.44 0.51 0.56 0.58 0.60 0.62
3.00 and above 0.44 0.51 0.57 0.6 0.62 0.63

Maximum shear stress tc.max in concrete (IS : 456-2000)

Grade of concrete M-15 M-20 M-25 M-30 M-35 M-40

tc.max 1.6 1.8 1.9 2.2 2.3 2.5

Shear stress tc Reiforcement %

100As 100As
M-20 M-20
bd bd
0.15 0.18 0.18 0.15
0.16 0.18 0.19 0.18
0.17 0.18 0.2 0.21
0.18 0.19 0.21 0.24
0.19 0.19 0.22 0.27
0.2 0.19 0.23 0.3
0.21 0.2 0.24 0.32
0.22 0.2 0.25 0.35
0.23 0.2 0.26 0.38
0.24 0.21 0.27 0.41
0.25 0.21 0.28 0.44
0.26 0.21 0.29 0.47
0.27 0.22 0.30 0.5
0.28 0.22 0.31 0.55
0.29 0.22 0.32 0.6
0.3 0.23 0.33 0.65
0.31 0.23 0.34 0.7
0.32 0.24 0.35 0.75
0.33 0.24 0.36 0.82
0.34 0.24 0.37 0.88
0.35 0.25 0.38 0.94
0.36 0.25 0.39 1.00
0.37 0.25 0.4 1.08
0.38 0.26 0.41 1.16
0.39 0.26 0.42 1.25
0.4 0.26 0.43 1.33
0.41 0.27 0.44 1.41
0.42 0.27 0.45 1.50
0.43 0.27 0.46 1.63
0.44 0.28 0.46 1.64
0.45 0.28 0.47 1.75
0.46 0.28 0.48 1.88
0.47 0.29 0.49 2.00
0.48 0.29 0.50 2.13
0.49 0.29 0.51 2.25
0.5 0.30
0.51 0.30
0.52 0.30
0.53 0.30
0.54 0.30
0.55 0.31
0.56 0.31
0.57 0.31
0.58 0.31
0.59 0.31
0.6 0.32
0.61 0.32
0.62 0.32
0.63 0.32
0.64 0.32
0.65 0.33
0.66 0.33
0.67 0.33
0.68 0.33
0.69 0.33
0.7 0.34
0.71 0.34
0.72 0.34
0.73 0.34
0.74 0.34
0.75 0.35
0.76 0.35
0.77 0.35
0.78 0.35
0.79 0.35
0.8 0.35
0.81 0.35
0.82 0.36
0.83 0.36
0.84 0.36
0.85 0.36
0.86 0.36
0.87 0.36
0.88 0.37
0.89 0.37
0.9 0.37
0.91 0.37
0.92 0.37
0.93 0.37
0.94 0.38
0.95 0.38
0.96 0.38
0.97 0.38
0.98 0.38
0.99 0.38
1.00 0.39
1.01 0.39
1.02 0.39
1.03 0.39
1.04 0.39
1.05 0.39
1.06 0.39
1.07 0.39
1.08 0.4
1.09 0.4
1.10 0.4
1.11 0.4
1.12 0.4
1.13 0.4
1.14 0.4
1.15 0.4
1.16 0.41
1.17 0.41
1.18 0.41
1.19 0.41
1.20 0.41
1.21 0.41
1.22 0.41
1.23 0.41
1.24 0.41
1.25 0.42
1.26 0.42
1.27 0.42
1.28 0.42
1.29 0.42
1.30 0.42
1.31 0.42
1.32 0.42
1.33 0.43
1.34 0.43
1.35 0.43
1.36 0.43
1.37 0.43
1.38 0.43
1.39 0.43
1.40 0.43
1.41 0.44
1.42 0.44
1.43 0.44
1.44 0.44
1.45 0.44
1.46 0.44
1.47 0.44
1.48 0.44
1.49 0.44
1.50 0.45
1.51 0.45
1.52 0.45
1.53 0.45
1.54 0.45
1.55 0.45
1.56 0.45
1.57 0.45
1.58 0.45
1.59 0.45
1.60 0.45
1.61 0.45
1.62 0.45
1.63 0.46
1.64 0.46
1.65 0.46
1.66 0.46
1.67 0.46
1.68 0.46
1.69 0.46
1.70 0.46
1.71 0.46
1.72 0.46
1.73 0.46
1.74 0.46
1.75 0.47
1.76 0.47
1.77 0.47
1.78 0.47
1.79 0.47
1.80 0.47
1.81 0.47
1.82 0.47
1.83 0.47
1.84 0.47
1.85 0.47
1.86 0.47
1.87 0.47
1.88 0.48
1.89 0.48
1.90 0.48
1.91 0.48
1.92 0.48
1.93 0.48
1.94 0.48
1.95 0.48
1.96 0.48
1.97 0.48
1.98 0.48
1.99 0.48
2.00 0.49
2.01 0.49
2.02 0.49
2.03 0.49
2.04 0.49
2.05 0.49
2.06 0.49
2.07 0.49
2.08 0.49
2.09 0.49
2.10 0.49
2.11 0.49
2.12 0.49
2.13 0.50
2.14 0.50
2.15 0.50
2.16 0.50
2.17 0.50
2.18 0.50
2.19 0.50
2.20 0.50
2.21 0.50
2.22 0.50
2.23 0.50
2.24 0.50
2.25 0.51
2.26 0.51
2.27 0.51
2.28 0.51
2.29 0.51
2.30 0.51
2.31 0.51
2.32 0.51
2.33 0.51
2.34 0.51
2.35 0.51
2.36 0.51
2.37 0.51
2.38 0.51
2.39 0.51
2.40 0.51
2.41 0.51
2.42 0.51
2.43 0.51
2.44 0.51
2.45 0.51
2.46 0.51
2.47 0.51
2.48 0.51
2.49 0.51
2.50 0.51
2.51 0.51
2.52 0.51
2.53 0.51
2.54 0.51
2.55 0.51
2.56 0.51
2.57 0.51
2.58 0.51
2.59 0.51
2.60 0.51
2.61 0.51
2.62 0.51
2.63 0.51
2.64 0.51
2.65 0.51
2.66 0.51
2.67 0.51
2.68 0.51
2.69 0.51
2.70 0.51
2.71 0.51
2.72 0.51
2.73 0.51
2.74 0.51
2.75 0.51
2.76 0.51
2.77 0.51
2.78 0.51
2.79 0.51
2.80 0.51
2.81 0.51
2.82 0.51
2.83 0.51
2.84 0.51
2.85 0.51
2.86 0.51
2.87 0.51
2.88 0.51
2.89 0.51
2.90 0.51
2.91 0.51
2.92 0.51
2.93 0.51
2.94 0.51
2.95 0.51
2.96 0.51
2.97 0.51
2.98 0.51
2.99 0.51
3.00 0.51
3.01 0.51
3.02 0.51
3.03 0.51
3.04 0.51
3.05 0.51
3.06 0.51
3.07 0.51
3.08 0.51
3.09 0.51
3.10 0.51
3.11 0.51
3.12 0.51
3.13 0.51
3.14 0.51
3.15 0.51
 Permissible Bond stress Table t bd in concrete (IS : 456-2000)
Grade of concrete M-10 M-15 M-20 M-25 M-30 M-35 M-40 M-45
tbd (N / mm2) -- 0.6 0.8 0.9 1 1.1 1.2 1.3

Development Length in tension

Grade of Plain M.S. Bars H.Y.S.D. Bars

concrete tbd (N / mm2) kd = Ld F tbd (N / mm2) kd = Ld F
M 15 0.6 58 0.96 60
M 20 0.8 44 1.28 45
M 25 0.9 39 1.44 40
M 30 1 35 1.6 36
M 35 1.1 32 1.76 33
M 40 1.2 29 1.92 30
M 45 1.3 27 2.08 28
M 50 1.4 25 2.24 26

Permissible stress in concrete (IS : 456-2000)

Permission stress in compression (N/mm2) Permissible stress in bond (Average) for
Grade of Bending acbc Direct (acc) plain bars in tention (N/mm2)
concrete
(N/mm2) Kg/m2 (N/mm2) Kg/m2 (N/mm2) in kg/m2
M 10 3.0 300 2.5 250 -- --
M 15 5.0 500 4.0 400 0.6 60
M 20 7.0 700 5.0 500 0.8 80
M 25 8.5 850 6.0 600 0.9 90
M 30 10.0 1000 8.0 800 1.0 100
M 35 11.5 1150 9.0 900 1.1 110
M 40 13.0 1300 10.0 1000 1.2 120
M 45 14.5 1450 11.0 1100 1.3 130
M 50 16.0 1600 12.0 1200 1.4 140

Permissible direct tensile stress in concrete (IS : 456-2000)

Grade of concrete M-10 M-15 M-20 M-25 M-30 M-35 M-40

sct.max 1.2 2.0 2.8 3.2 3.6 4.0 4.4
M-50
1.4