Experiment # 4: DSB and SSB Modulation Using MATLAB Built-In Commands

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 12

Anaolg & Digtal Communication LAB MANUAL

Name Muhammad Sohaib Choudhary


Reg# 2015-EE-484
Marks/Grade

Experiment # 4

DSB and SSB modulation using MATLAB Built- in commands


Objective:
Use the Simulink to implement the Single side band modulation and Double side band
modulation
SSB Modulation:
The baseband message can be transmitted by using only one of the sidebands and, consequently,
half the bandwidth of AM or DSBSC-AM. This type of modulation is called single-sideband (SSB)
modulation. It has been extensively used in many radio transmission systems and in the telephone
network. The block diagram to generate SSB modulated signal . Translating the frequency spectrum
of a signal is closely related to SSB modulation and is commonly used at various points in
communication systems.

For a filter to be physically realizable, the transmission band separating the pass-band from the stop
band must have a finite width. The band-pass filter demands that there be an adequate separation
between the lower sideband and the upper sideband of the DSB-SC modulated wave produced at
the output of the product modulator

INSTRUCTOR:SIR.ALI RAZA 1
Anaolg & Digtal Communication LAB MANUAL

INSTRUCTOR:SIR.ALI RAZA 2
Anaolg & Digtal Communication LAB MANUAL

Matlab code:

Output:

Figure 1 single side band graph

INSTRUCTOR:SIR.ALI RAZA 3
Anaolg & Digtal Communication LAB MANUAL

Simulink model:

Output:

INSTRUCTOR:SIR.ALI RAZA 4
Anaolg & Digtal Communication LAB MANUAL

DSB Modulation:
The standard AM modulated signal contains a sinusoidal component at the carrier frequency which
does not convey any of the baseband message information []. This component is included to create
a positive envelope which allows demodulation by a simple, inexpensive envelope detector. From
an information theory point of view, the power in the sinusoidal carrier component is wasted.

The type of modulation that will be studied in this section is called double-sideband suppressed-
carrier amplitude modulation (DSBSC-AM).
Double-sideband suppressed-carrier transmission (DSB-SC) is transmission in which frequencies
produced by amplitude modulation (AM) are symmetrically spaced above and below the carrier
frequency and the carrier level is reduced to the lowest practical level, ideally being completely
suppressed. In the DSB-SC modulation, unlike in AM, the wave carrier is not transmitted; thus,
much of the power is distributed between the sideband, which implies an increase of the cover in
DSB-SC, compared to AM, for the same power used. It is used for radio data systems.

INSTRUCTOR:SIR.ALI RAZA 5
Anaolg & Digtal Communication LAB MANUAL

Matlab code:

Output:

INSTRUCTOR:SIR.ALI RAZA 6
Anaolg & Digtal Communication LAB MANUAL

Simulink model:

INSTRUCTOR:SIR.ALI RAZA 7
Anaolg & Digtal Communication LAB MANUAL

Output:

Upper and Lower side band:


Matlab code:

INSTRUCTOR:SIR.ALI RAZA 8
Anaolg & Digtal Communication LAB MANUAL

INSTRUCTOR:SIR.ALI RAZA 9
Anaolg & Digtal Communication LAB MANUAL

Outputs:

INSTRUCTOR:SIR.ALI RAZA 10
Anaolg & Digtal Communication LAB MANUAL

INSTRUCTOR:SIR.ALI RAZA 11
Anaolg & Digtal Communication LAB MANUAL

CONCLUSION:
All the simulations have done in Matlab Simulink (R2015a). First DSBSC signal is generated with
different modulating and carrier signal frequencies. Modulating signal, carrier and DSBSC signal
and their spectrum are shown in Fig. From all simulation and Literature surveys it is concluded
that SSB modulated signal and VSB signal requires special filters to one side band and thus
resulting high performance with respect to power and bandwidth.

INSTRUCTOR:SIR.ALI RAZA 12

You might also like