Scribd
Upload
434 views4 pages

Toyota - Linear Valve Learn Value Initialization

This document provides instructions for initializing the linear valve learn value in Toyota ABS systems after replacing the brake executor. It involves using the X431 TOYOTA program's working support menu to enter a 3-step initialization process, which resets communication between brake components. Selecting "YES" at each step advances the process. A warning light may illuminate after, but can be cleared by putting the ABS in check or normal mode via the mode change menu.

Uploaded by

Gerald Louie Uy Meguizo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
434 views4 pages

Toyota - Linear Valve Learn Value Initialization

This document provides instructions for initializing the linear valve learn value in Toyota ABS systems after replacing the brake executor. It involves using the X431 TOYOTA program's working support menu to enter a 3-step initialization process, which resets communication between brake components. Selecting "YES" at each step advances the process. A warning light may illuminate after, but can be cleared by putting the ABS in check or normal mode via the mode change menu.

Uploaded by

Gerald Louie Uy Meguizo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Linear Valve Learn Value Initialization

Launch Software TOYOTA Engineer


Li Yongshuai
The function is available in the working supporting menu of ABS of X431 TOYOTA
program. The non-CANBUS systems must be used TOYOTA-16 connector or CAN BUS II
connector.
The main procedures are introduced as below:

图1 图2
Now I introduce the operation and components relating to it. While Driver is doing brake
operation, pedal journey sensor detects the brake intention of driver, which the sensor
transfer to ECU. ECU collects the signals from rpm sensor, steering angle sensor, etc,
work out the brake power of every wheel according to the driving status, and send
command to pressure storage can of executor to execute the brake of every wheel.
Fig. 3 shows that how brake control ECU follows the brake intention.

1
Brake
Brake Control
pressure
ECU
larger than
in traditional
Brake
mode.
Executor

Main Brake Pedal


Cylinder Journey Sensor
Pressure
Sensor

图3
After brake executor is replaced, the brake pedal journey sensor and brake control ECU
will execute the linear valve learn value initialization function. It will initialize the
communication between brake executor, brake pedal journey sensor and brake control
ECU.
Click [YES] in fig.2 if confirm the operation to enter Step 1/3. See fig.4.

图4
Note: please operate with ignition switch ON and in P position. Then press [YES] to enter
the Step 2/3 as shown in fig.5. Please operate following instructions.

2
图5 图6
Note: VSC/ABS warning light will be light after doing this operation. The light can’t be
cleared by clearing DTC function. The DTC is C1345/66-non-learning linear valve branch
is abnormal. .
The operation for extinguishing warning light is available in MODE CHANGE menu:
1. Turn ignition key ON when warning light is lit.
2. Turn ignition switch ON and enter the WORKING SUPPORT menu of ABS.
3. Under MODE CHANGE menu, make it in check mode.

图7 图8

Select [NO] to enter check mode in fig. 8.

3
图9 图 10
4. Now, ECB warning light will be flash. If not, please repeat the operation as mentioned
above till the frequency of warning light turn 1Hz to 4Hz.
Note: the frequency of unit time to be set is 1Hz.
5. It will take about 1 minute for the operation, which will be different as different vehicle.
6. Now, enter normal mode( or turn ignition switch OFF to normal mode), the warning
light will be extinguished.
Click “OK” in fig.10 to normal mode.

图 11 图 12

You might also like