BALL BEARING SERIES

Angular Contact Ball Bearings for Machining Tools

CAT.NO. B2006E
 Angular Contact Ball Bearings for Machining Tools

Machining tools regularly improve in speed and Moreover, environmental concerns are now a
efficiency in response to industrial demands for major issue, bringing into question the oil-and-air
increased productivity and product machining lubrication and oil mist lubrication usually used with
efficiency. Consequently, bearings for machining high-speed spindles. As an alternative, grease
tools are required to achieve the following lubrication is gaining attention as it does not spray
performance levels. oil into the air and ensures the environment is free
of contamination.
● Ultrafast rotation to reduce machining time In response to these needs, JTEKT has developed
● Rapid acceleration/deceleration capability for its High Ability bearing series. The newly
improved efficiency developed bearings offer excellent high-speed
● High rigidity with low increase in temperature performance and rapid acceleration and
for high precision machining deceleration performance and allow grease
lubrication for high-speed operations.

Contents

1. Features 2
2. Construction 3
3. Types and Bearing Numbers 4
4. Performance 5
5. Dimension Tables 7

Type R Steel Balls 7

Type R Ceramic Balls 10
Type C Ceramic Balls 13
Type D Ceramic Balls 16
Type F Ceramic Balls 17
1. Features
20 to 30% reduction in temperature increase
(compared with Koyo's conventional products)
Koyo has conducted various tests and analyses and de-
veloped elaborate machining techniques to improve the
performance of bearings used with machining tool spin-
dles. The result is a substantial reduction in frictional
heat generated in bearings rotating at a high speed.
1.2- to 1.5-fold increases in speed limits
(compared with Koyo's conventional products)
Speed limits have been extended through re-designing
for high-speed rotation and heat reduction. Use of cer-
amic balls as rolling elements enables additional high-
speed rotation.
Improved high-speed performance achieved by
position preloading
Low increases in temperature during operation ensure
reduced changes in preload. Preload can be given by
position preloading even at high speeds, which has been
hitherto unavailable with conventional systems. The re-
sult is high-precision machining with stability.
Conventional bearings easily replaced
Dimensions of High Ability bearings conform to ISO stan-
dards. Replacement of conventional bearings with High
Ability bearings requires minimal geometry changes of
the present spindle or housing.

Example of application to a high-speed, high-power spindle

d mn

2
 Angular Contact Ball Bearings for Machining Tools

2. Construction

There are four types of High Ability bearings.

Type R Outer ring This bearing has the same dimensions as conven-
Balls tional products. The limiting speed has been im-
proved by raceways machined to optimal geometry
Cage
for high-speed rotation. Balls are available in steel
Inner ring or ceramics.

Type C Outer ring An increased load rating has been achieved by in-
Balls creasing the size of the ball. The ball is ceramics
to ensure high-speed performance.
Cage

Inner ring

Type D Outer ring Type D is designed to supply oil to the ball via an
Balls
oiling groove and nozzle provided in one side of
the inner ring. Ceramic balls are used.
Cage

Inner ring

* Type D has been developed jointly with Mitsui Seiki Co., Ltd.

Type F Outer ring An oiling groove and nozzle are provided in the
Balls outer ring for reliable lubrication of the guide way
on the cage and the rolling contact surface of the
Cage ball. Type F is optimal for ultrafast rotation. Cer-
Inner ring amic balls are used.

Stator
Rotor
Oiling ports

3
3. Types and Bearing Numbers

(1) High Ability bearing types and principal applications

Specification
Type Remarks
Bearing dimension Material of
Contact angle rolling element
series
Steel
R
High-speed,
Type or high-rigidity type
ceramics

C
High-speed,
Type ceramics high load-rating type

Ultrafast, low-noise
Type D ceramics type for
oil-and-air lubrication

Extremely ultrafast
Type F ceramics type for
oil-and-air lubrication

(2) Bearing number nomenclature

E x a mp le

Internal clearance
5 : Denotes a medium value of
clearances of 5
CY : preload (negative clearance)
CS : clearance
Combination symbol
Typical examples of combination symbol
DB DF DT

Cage guide -5 : ball guided

No symbol : outer ring guided

Contact angle

Bore diameter number, 13: Denotes a bearing bore diameter of 5 mm x 13=65mm.

Dimension series, 9: dimension series 19
0: dimension series 10
High Ability bearing type, R, C, D, or F. See table above for details.

High Ability ball bearing series

Ceramic balls

4
 Angular Contact Ball Bearings for Machining Tools

4. Performance
The temperature of an operating bearing increases High Ability bearings also allow the possible
due to frictional heat produced within the bearing. change in lubrication of the spindle from oil-and-
This increase in temperature imposes a certain speed air to grease.
limit when the bearing is required to rotate at high
speed. Fig.2 shows an evaluation example.

The reason being that the bearing operation discon-

tinues due to seizure caused by temperature increa-
ses above a certain temperature. Consequently, in-
creases in bearing temperature during operation can d mn [ x106 ]
1.0 1.25 1.50 1.75 2.0
serve as a measure in regard to speed limit. 20
Preload : 150 N(position preloading)
High Ability bearings exhibit their maximum perfor- Cooling : jacket, oil-cooled
mance when used in pairs or when more than two 15

Temp. increase of outer ring

units are combined and when preload is given by posi- Oil-and-air lub.
3NC ACH013CA Grease lub.
tion preloading. Shown below is the operating perfor- 3NC HAR013CA
mance of High Ability bearings with preload given by 10
position preloading.
5
(1) High-speed performance of Types R and C
Fig.1 compares relationships between rotational
speed and increases in bearing temperature of 0
10 14 18 22 26
Types R and C and conventional high-precision [ x103 min-1 ]
Rotational speed
bearings.
High Ability bearings exhibit smaller tempera-
ture increases and higher speed limits than con-
ventional bearings whether grease lubrication or d mn [ x106 ]
oil-and-air lubrication is applied. 1.25 1.50
20
Preload : 150 N(position preloading)
Cooling : jacket, oil-cooled

15
Temp. increase of outer ring

Oil-and-air lub.
d mn [ x106 ] Grease lub.
ACH013CA
1.0 1.25 1.5 1.75 HAR013CA
40 10
Preload : 980 N(position preloading)
Cooling : jacket, oil-cooled 3NC HAC015C
Temp. increase of outer ring

30 5
3NC ACH015C

20 0
10 12 14 16 18
[ x103 min-1 ]
10 Rotational speed

0
16 18 20
Fig. 2 Comparison of High-speed Performance
8 10 12 14
Rotational speed
[ x103 min-1 ] Achieved by Grease Lubrication

Type R high ability bearing and grease lubrica-

tion exhibits better high-speed performance than
d mn [ x106 ] conventional bearings using oil-and-air lubrica-
60
1.0 1.25 1.5 1.75 tion.
Preload : 150 N(position preloading)
Cooling : self-cooling HAR013CA If steel balls are used, Type R with grease lubri-
Temp. increase of outer ring

cation exhibits high-speed performance equal to

40
ACH013CA
or better than conventional bearings with oil-and-
air lubrication.

20

0
10 12 14 16 18 20 22
[ x103 min-1 ]
Rotational speed

Fig. 1 Comparison of Increases in Bearing

Temp. with Oil-and-air Lubrication

5
(2) High-speed performance of Type D (3) High-speed performance of Type F
High Ability Type D bearings are designed for The oiling port in Type F is provided at its outer
oil-and-air lubrication. Their inner rings have an ring to ensure improved lubrication reliability on
oiling groove to ensure lubrication on the rolling the guide ways of the cage. High Ability bearings
contact surface for improved lubrication reliability. of Type F deliver the best high-speed performance.

Oiling Oiling Oiling

Outer ring Outer ring Outer ring Outer ring

spacer spacer
Balls Balls
Oiling port
Oiling port
Cage Cage

Inner ring Inner ring

Inner ring Inner ring
spacer spacer

Oiling groove Lubrication is accomplished from one side

The oiling nozzle should be aligned with via the outer ring.
the oiling groove in the inner ring.
Fig. 6 Lubrication method used in Type F
Fig. 3 Lubrication Method for Type D
Figure 7 shows an evaluation example of the
Fig.4 compares the high-speed performance of Type F bearing operated with a preload given by
Types D and R. constant pressure preloading. The maximum ro-
tational speed achieved in this test, or 54 000
d mn [ x106 ]
min-1, equals 3.3 ×106 in dmn value.
1.5 2.0 2.5
80
● Evaluation of bearing with a preload given
Temp. increase of outer ring [℃]

Preload：40 N(position preloading)

Cooling：self-cooling by constant pressure preloading
60 d mn [ x106 ]
Type R
2.0 2.5 3.0
3NC HAR007CA Type D 40
Temp. increase of outer ring [℃]

Preload：500 N(constant pressure preloading)

40 3NC HAD007CA Cooling：jacket, oil-cooled

30 3NC HAF910CA
20

20
0
30 34 38 42 46 50 54
[ x103 min-1 ] 10
Rotational speed

Fig. 4 Comparison of Increases in the 0

30 34 38 42 46 50 54
Bearing Temp. of Types R and D Rotational speed [ x103 min-1 ]

Furthermore, Type D bearings generate only a Fig. 7 Temp. Increases in Type F Bearing
slight noise during rotation and are therefore also
effective for noise reduction of spindle units The oiling port in the outer ring provides sufficient
(Fig. 5). lubrication to achieve a substantial reduction of
friction on guide ways of the cage. This lubrication
100
method ensures excellent stability against rapid
Preload：40 N(position preloading) acceleration or deceleration during operation.
Cooling：self-cooling Type R
3NC HAR007CA
90 Passes 105 cycles of 0 to 46 000min-1in 3s
Sound pressure [dBA]

acceleration/deceleration（46 000 min-1＝dmn 2.8×106）

80
Type D 30
3NC HAD007CA
● Bearing number Rotational
speed 3 10 3 14
70 ：3NC HAF910CA
[ min-1 ]
● Preload
：constant pressure 46 000
preloading
60
30 40 50 ● Cooling

[ x103 min-1 ] ：jacket, oil-cooled

Rotational speed 0
● Test pattern
：See figure at right. Time [s]
Fig. 5 Comparison of Noise by Types R and D
Fig. 8 Operating Pattern of Type F Involving
Rapid Acceleration and Deceleration

6
 BALL BEARING SERIES

Dimension table
B
Type R
Steel balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
HAR006C 8.70 4.85 26 000 40 000
30 55 13 HAR006CA 8.55 4.75 25 000 38 000
HAR006 8.00 4.45 18 000 24 000
HAR007C 9.25 5.55 23 000 35 000
35 62 14 HAR007CA 9.05 5.40 22 000 33 000
HAR007 8.45 5.05 15 000 21 000
HAR908C 6.35 4.05 22 000 33 000
62 12 HAR908CA 6.20 3.95 21 000 31 000
HAR908 5.75 3.70 15 000 20 000
40
HAR008C 9.70 6.20 20 000 31 000
68 15 HAR008CA 9.50 6.05 19 000 30 000
HAR008 8.85 5.65 14 000 19 000
HAR909C 6.80 4.70 19 000 30 000
68 12 HAR909CA 6.65 4.55 19 000 28 000
HAR909 6.15 4.25 13 000 18 000
45
HAR009C 10.9 7.10 18 000 28 000
75 16 HAR009CA 10.6 6.95 18 000 27 000
HAR009 9.90 6.45 13 000 17 000
HAR910C 9.10 6.30 18 000 28 000
72 12 HAR910CA 8.90 6.15 17 000 26 000
HAR910 8.25 5.75 12 000 16 000
50
HAR010C 11.4 7.85 17 000 26 000
80 16 HAR010CA 11.1 7.65 16 000 25 000
HAR010 10.4 7.15 12 000 15 000
HAR911C 10.1 7.65 16 000 25 000
80 13 HAR911CA 9.85 7.50 16 000 24 000
HAR911 9.15 6.95 11 000 15 000
55
HAR011C 14.1 9.90 15 000 23 000
90 18 HAR011CA 13.7 9.70 14 000 22 000
HAR011 12.8 9.00 10 000 14 000
HAR912C 9.95 7.75 15 000 23 000
85 13 HAR912CA 9.70 7.55 14 000 22 000
HAR912 9.00 7.00 10 000 14 000
60
HAR012C 14.7 10.8 14 000 22 000
95 18 HAR012CA 14.3 10.6 14 000 21 000
HAR012 13.4 9.85 10 000 13 000
HAR913C 11.8 9.45 14 000 22 000
90 13 HAR913CA 11.5 9.25 14 000 21 000
HAR913 10.7 8.55 9 700 13 000
65
HAR013C 15.3 11.8 13 000 21 000
100 18 HAR013CA 14.9 11.5 13 000 19 000
HAR013 13.9 10.7 9 100 12 000
HAR914C 12.9 10.5 13 000 20 000
100 16 HAR914CA 12.6 10.2 12 000 19 000
HAR914 11.7 9.45 8 800 12 000
70
HAR014C 20.7 15.5 12 000 19 000
110 20 HAR014CA 20.2 15.1 12 000 18 000
HAR014 18.9 14.1 8 300 11 000

7
BALL BEARING SERIES

Dimension table
B
Type R
Steel balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
HAR915C 13.3 11.2 12 000 19 000
105 16 HAR915CA 12.9 10.9 12 000 18 000
HAR915 12.0 10.1 8 300 11 000
75
HAR015C 21.1 16.2 12 000 18 000
115 20 HAR015CA 20.6 15.8 11 000 17 000
HAR015 19.2 14.7 7 900 11 000
HAR916C 13.6 11.9 12 000 18 000
110 16 HAR916CA 13.3 11.6 11 000 17 000
HAR916 12.3 10.8 7 900 11 000
80
HAR016C 24.7 19.2 10 000 16 000
125 22 HAR016CA 24.1 18.8 9 700 15 000
HAR016 22.5 17.5 7 000 9 300
HAR917C 16.3 14.2 10 000 16 000
120 18 HAR917CA 15.9 13.8 9 700 15 000
HAR917 14.8 12.8 7 000 9 300
85
HAR017C 25.1 20.1 9 700 15 000
130 22 HAR017CA 24.5 19.6 9 300 14 000
HAR017 22.8 18.3 6 600 8 800
HAR918C 16.8 15.1 9 700 15 000
125 18 HAR918CA 16.4 14.7 9 300 14 000
HAR918 15.2 13.7 6 600 8 800
90
HAR018C 32.8 26.1 9 100 14 000
140 24 HAR018CA 32.0 25.4 8 700 13 000
HAR018 29.8 23.7 6 200 8 300
HAR919C 17.3 16.0 9 300 14 000
130 18 HAR919CA 16.9 15.6 8 900 14 000
HAR919 15.6 14.5 6 300 8 400
95
HAR019C 33.4 27.2 8 700 13 000
145 24 HAR019CA 32.6 26.6 8 300 13 000
HAR019 30.4 24.7 5 900 7 900
HAR920C 24.2 21.7 8 700 13 000
140 20 HAR920CA 23.6 21.2 8 300 13 000
HAR920 21.9 19.7 5 900 7 900
100
HAR020C 34.0 28.4 8 400 13 000
150 24 HAR020CA 33.2 27.7 8 000 12 000
HAR020 30.9 25.8 5 700 7 600
HAR921C 24.9 23.1 8 400 13 000
145 20 HAR921CA 24.3 22.5 8 000 12 000
HAR921 22.5 20.9 5 700 7 600
105
HAR021C 38.6 32.5 7 900 12 000
160 26 HAR021CA 37.6 31.7 7 500 11 000
HAR021 35.0 29.5 5 400 7 200
HAR922C 25.1 23.8 8 000 12 000
150 20 HAR922CA 24.5 23.2 7 700 12 000
HAR922 22.8 21.6 5 500 7 300
110
HAR022C 43.4 37.0 7 500 12 000
170 28 HAR022CA 42.4 36.1 7 100 11 000
HAR022 39.4 33.6 5 100 6 800

8
 BALL BEARING SERIES

Dimension table
B
Type R
Steel balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
HAR924C 29.4 28.4 7 300 11 000
165 22 HAR924CA 28.6 27.7 7 000 11 000
HAR924 26.6 25.7 5 000 6 700
120
HAR024C 44.9 39.9 7 000 11 000
180 28 HAR024CA 43.8 39.0 6 700 10 000
HAR024 40.7 36.2 4 800 6 300
HAR926C 35.1 35.1 6 700 10 000
180 24 HAR926CA 34.2 34.3 6 400 9 800
HAR926 31.7 31.8 4 600 6 100
130
HAR026C 56.3 48.4 6 300 9 800
200 33 HAR026CA 55.0 47.2 6 000 9 200
HAR026 51.2 43.9 4 300 5 800
HAR928C 35.2 36.2 6 300 9 800
190 24 HAR928CA 34.3 35.3 6 000 9 200
HAR928 31.8 32.8 4 300 5 800
140
HAR028C 61.3 56.2 6 000 9 200
210 33 HAR028CA 59.9 54.8 5 700 8 700
HAR028 55.7 51.0 4 100 5 400
HAR930C 48.9 48.9 5 800 9 000
210 28 HAR930CA 47.7 47.6 5 500 8 400
HAR930 44.3 44.2 4 000 5 300
150
HAR030C 72.2 66.1 5 300 8 200
225 35 HAR030CA 70.5 64.5 5 000 7 700
HAR030 65.6 60.0 3 600 4 800
HAR932C 50.2 51.8 5 200 8 100
220 28 HAR932CA 48.9 50.5 5 000 7 600
HAR932 45.4 46.9 3 600 4 700
160
HAR032C 78.3 72.7 5 000 7 700
240 38 HAR032CA 76.4 71.0 4 700 7 200
HAR032 71.1 66.0 3 400 4 500
HAR934C 51.4 54.8 5 000 7 700
230 28 HAR934CA 50.1 53.4 4 700 7 200
HAR934 46.4 49.6 3 400 4 500
170
HAR034C 91.8 86.4 4 600 7 100
260 42 HAR034CA 89.6 84.3 4 400 6 700
HAR034 83.4 78.4 3 100 4 200

9
BALL BEARING SERIES

Dimension table
B
Type R
Ceramic balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
3NCHAR006C 8.70 4.85 35 000 59 000
30 55 13 3NCHAR006CA 8.55 4.75 33 000 55 000
3NCHAR006 8.00 4.45 25 000 35 000
3NCHAR007C 9.25 5.55 31 000 52 000
35 62 14 3NCHAR007CA 9.05 5.40 29 000 48 000
3NCHAR007 8.45 5.05 22 000 31 000
3NCHAR908C 6.35 4.05 29 000 49 000
62 12 3NCHAR908CA 6.20 3.95 27 000 46 000
3NCHAR908 5.75 3.70 21 000 29 000
40
3NCHAR008C 9.70 6.20 28 000 46 000
68 15 3NCHAR008CA 9.50 6.05 26 000 44 000
3NCHAR008 8.85 5.65 19 000 28 000
3NCHAR909C 6.80 4.70 27 000 44 000
68 12 3NCHAR909CA 6.65 4.55 25 000 42 000
3NCHAR909 6.15 4.25 19 000 27 000
45
3NCHAR009C 10.9 7.10 25 000 42 000
75 16 3NCHAR009CA 10.6 6.95 23 000 39 000
3NCHAR009 9.90 6.45 18 000 25 000
3NCHAR910C 9.10 6.30 25 000 41 000
72 12 3NCHAR910CA 8.90 6.15 23 000 39 000
3NCHAR910 8.25 5.75 17 000 25 000
50
3NCHAR010C 11.4 7.85 23 000 38 000
80 16 3NCHAR010CA 11.1 7.65 22 000 36 000
3NCHAR010 10.4 7.15 16 000 23 000
3NCHAR911C 10.1 7.65 22 000 37 000
80 13 3NCHAR911CA 9.85 7.50 21 000 35 000
3NCHAR911 9.15 6.95 16 000 22 000
55
3NCHAR011C 14.1 9.90 21 000 34 000
90 18 3NCHAR011CA 13.7 9.70 19 000 32 000
3NCHAR011 12.8 9.00 14 000 21 000
3NCHAR912C 9.95 7.75 21 000 34 000
85 13 3NCHAR912CA 9.70 7.55 19 000 32 000
3NCHAR912 9.00 7.00 14 000 21 000
60
3NCHAR012C 14.7 10.8 19 000 32 000
95 18 3NCHAR012CA 14.3 10.6 18 000 30 000
3NCHAR012 13.4 9.85 14 000 19 000
3NCHAR913C 11.8 9.45 19 000 32 000
90 13 3NCHAR913CA 11.5 9.25 18 000 30 000
3NCHAR913 10.7 8.55 14 000 19 000
65
3NCHAR013C 15.3 11.8 18 000 30 000
100 18 3NCHAR013CA 14.9 11.5 17 000 28 000
3NCHAR013 13.9 10.7 13 000 18 000
3NCHAR914C 12.9 10.5 18 000 29 000
100 16 3NCHAR914CA 12.6 10.2 16 000 28 000
3NCHAR914 11.7 9.45 12 000 18 000
70
3NCHAR014C 20.7 15.5 17 000 28 000
110 20 3NCHAR014CA 20.2 15.1 16 000 26 000
3NCHAR014 18.9 14.1 12 000 17 000

10
 BALL BEARING SERIES

Dimension table
B
Type R
Ceramic balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
3NCHAR915C 13.3 11.2 17 000 28 000
105 16 3NCHAR915CA 12.9 10.9 16 000 26 000
3NCHAR915 12.0 10.1 12 000 17 000
75
3NCHAR015C 21.1 16.2 16 000 26 000
115 20 3NCHAR015CA 20.6 15.8 15 000 25 000
3NCHAR015 19.2 14.7 11 000 16 000
3NCHAR916C 13.6 11.9 16 000 26 000
110 16 3NCHAR916CA 13.3 11.6 15 000 25 000
3NCHAR916 12.3 10.8 11 000 16 000
80
3NCHAR016C 24.7 19.2 14 000 23 000
125 22 3NCHAR016CA 24.1 18.8 13 000 22 000
3NCHAR016 22.5 17.5 9 700 14 000
3NCHAR917C 16.3 14.2 14 000 23 000
120 18 3NCHAR917CA 15.9 13.8 13 000 22 000
3NCHAR917 14.8 12.8 9 700 14 000
85
3NCHAR017C 25.1 20.1 13 000 22 000
130 22 3NCHAR017CA 24.5 19.6 12 000 21 000
3NCHAR017 22.8 18.3 9 300 13 000
3NCHAR918C 16.8 15.1 13 000 22 000
125 18 3NCHAR918CA 16.4 14.7 12 000 21 000
3NCHAR918 15.2 13.7 9 300 13 000
90
3NCHAR018C 32.8 26.1 12 000 21 000
140 24 3NCHAR018CA 32.0 25.4 12 000 19 000
3NCHAR018 29.8 23.7 8 700 12 000
3NCHAR919C 17.3 16.0 13 000 21 000
130 18 3NCHAR919CA 16.9 15.6 12 000 20 000
3NCHAR919 15.6 14.5 8 900 13 000
95
3NCHAR019C 33.4 27.2 12 000 20 000
145 24 3NCHAR019CA 32.6 26.6 11 000 19 000
3NCHAR019 30.4 24.7 8 300 12 000
3NCHAR920C 24.2 21.7 12 000 20 000
140 20 3NCHAR920CA 23.6 21.2 11 000 19 000
3NCHAR920 21.9 19.7 8 300 12 000
100
3NCHAR020C 34.0 28.4 11 000 19 000
150 24 3NCHAR020CA 33.2 27.7 11 000 18 000
3NCHAR020 30.9 25.8 8 000 11 000
3NCHAR921C 24.9 23.1 11000 19 000
145 20 3NCHAR921CA 24.3 22.5 11 000 18 000
3NCHAR921 22.5 20.9 8 000 11 000
105
3NCHAR021C 38.6 32.5 11 000 18 000
160 26 3NCHAR021CA 37.6 31.7 10 000 17 000
3NCHAR021 35.0 29.5 7 500 11 000
3NCHAR922C 25.1 23.8 11 000 18 000
150 20 3NCHAR922CA 24.5 23.2 10 000 17 000
3NCHAR922 22.8 21.6 7 700 11 000
110
3NCHAR022C 43.4 37.0 10 000 17 000
170 28 3NCHAR022CA 42.4 36.1 9 500 16 000
3NCHAR022 39.4 33.6 7 100 10 000

11
BALL BEARING SERIES

Dimension table
B
Type R
Ceramic balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
3NCHAR924C 29.4 28.4 10 000 17 000
165 22 3NCHAR924CA 28.6 27.7 9 300 16 000
3NCHAR924 26.6 25.7 7 000 10 000
120
3NCHAR024C 44.9 39.9 9 500 16 000
180 28 3NCHAR024CA 43.8 39.0 8 900 15 000
3NCHAR024 40.7 36.2 6 700 9 500
3NCHAR926C 35.1 35.1 9 200 15 000
180 24 3NCHAR926CA 34.2 34.3 8 600 14 000
3NCHAR926 31.7 31.8 6 400 9 200
130
3NCHAR026C 56.3 48.4 8 600 14 000
200 33 3NCHAR026CA 55.0 47.2 8 100 14 000
3NCHAR026 51.2 43.9 6 000 8 600
3NCHAR928C 35.2 36.2 8 600 14 000
190 24 3NCHAR928CA 34.3 35.3 8 100 14 000
3NCHAR928 31.8 32.8 6 000 8 600
140
3NCHAR028C 61.3 56.2 8 100 14 000
210 33 3NCHAR028CA 59.9 54.8 7 600 13 000
3NCHAR028 55.7 51.0 5 700 8 100
3NCHAR930C 48.9 48.9 7 900 13 000
210 28 3NCHAR930CA 47.7 47.6 7 400 12 000
3NCHAR930 44.3 44.2 5 500 7 900
150
3NCHAR030C 72.2 66.1 7 200 12 000
225 35 3NCHAR030CA 70.5 64.5 6 700 11 000
3NCHAR030 65.6 60.0 5 000 7 200
3NCHAR932C 50.2 51.8 7 100 12 000
220 28 3NCHAR932CA 48.9 50.5 6 600 11 000
3NCHAR932 45.4 46.9 5 000 7 100
160
3NCHAR032C 78.3 72.7 6 800 11 000
240 38 3NCHAR032CA 76.4 71.0 6 300 11 000
3NCHAR032 71.1 66.0 4 700 6 800
3NCHAR934C 51.4 54.8 6 800 11 000
230 28 3NCHAR934CA 50.1 53.4 6 300 11 000
3NCHAR934 46.4 49.6 4 700 6 800
170
3NCHAR034C 91.8 86.4 6 300 10 000
260 42 3NCHAR034CA 89.6 84.3 5 900 9 800
3NCHAR034 83.4 78.4 4 400 6 300

12
 BALL BEARING SERIES

Dimension table
B
Type C
Ceramic balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
3NCHAC900C 2.05 0.77 94 000 156 000
22 6
3NCHAC900CA 2.00 0.76 88 000 147 000
10
3NCHAC000C 3.50 1.25 85 000 141 000
26 8
3NCHAC000CA 3.50 1.25 79 000 133 000
3NCHAC901C 2.15 0.87 83 000 139 000
24 6
3NCHAC901CA 2.10 0.86 78 000 131 000
12
3NCHAC001C 3.90 1.50 73 000 122 000
28 8
3NCHAC001CA 3.85 1.45 68 000 115 000
3NCHAC902C 3.20 1.35 70 000 116 000
28 7
3NCHAC902CA 3.15 1.30 65 000 109 000
15
3NCHAC002C 4.45 1.90 64 000 106 000
32 9
3NCHAC002CA 4.40 1.85 60 000 100 000
3NCHAC903C 3.40 1.50 63 000 104 000
30 7
3NCHAC903CA 3.35 1.45 58 000 98 000
17
3NCHAC003C 4.95 2.30 57 000 94 000
35 10
3NCHAC003CA 4.85 2.25 53 000 89 000
3NCHAC904C 4.95 2.35 53 000 88 000
37 9
3NCHAC904CA 4.85 2.30 49 000 82 000
20
3NCHAC004C 7.50 3.35 48 000 79 000
42 12
3NCHAC004CA 7.35 3.30 44 000 75 000
3NCHAC905C 5.40 2.75 44 000 73 000
42 9
3NCHAC905CA 5.30 2.70 41 000 69 000
25
3NCHAC005C 8.35 4.10 42 000 69 000
47 12
3NCHAC005CA 8.20 4.00 39 000 65 000
3NCHAC906C 5.75 3.20 39 000 65 000
47 9
3NCHAC906CA 5.65 3.10 36 000 61 000
30
3NCHAC006C 10.8 5.60 35 000 59 000
55 13
3NCHAC006CA 10.6 5.50 33 000 55 000
3NCHAC907C 8.65 4.90 33 000 56 000
55 10
3NCHAC907CA 8.50 4.80 31 000 52 000
35
3NCHAC007C 13.0 7.00 31 000 51 000
62 14
3NCHAC007CA 12.8 6.85 29 000 48 000
3NCHAC908C 10.9 6.30 29 000 49 000
62 12
3NCHAC908CA 10.6 6.20 27 000 46 000
40
3NCHAC008C 14.1 8.10 28 000 46 000
68 15
3NCHAC008CA 13.8 7.90 26 000 44 000
3NCHAC909C 11.5 7.15 27 000 44 000
68 12
3NCHAC909CA 11.3 7.00 25 000 42 000
45
3NCHAC009C 16.8 9.80 25 000 42 000
75 16
3NCHAC009CA 16.4 9.60 23 000 39 000

13
BALL BEARING SERIES

Dimension table
B
Type C
Ceramic balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
3NCHAC910C 12.2 7.95 25 000 41 000
72 12
3NCHAC910CA 11.9 7.80 23 000 39 000
50
3NCHAC010C 17.9 11.2 23 000 38 000
80 16
3NCHAC010CA 17.6 10.9 21 000 36 000
3NCHAC911C 13.8 9.40 22 000 37 000
80 13
3NCHAC911CA 13.5 9.20 21 000 35 000
55
3NCHAC011C 23.5 14.6 21 000 34 000
90 18
3NCHAC011CA 23.0 14.3 19 000 32 000
3NCHAC912C 16.3 11.1 21 000 34 000
85 13
3NCHAC912CA 15.9 10.8 19 000 32 000
60
3NCHAC012C 24.2 15.6 19 000 32 000
95 18
3NCHAC012CA 23.7 15.3 18 000 30 000
3NCHAC913C 14.7 10.8 19 000 32 000
90 13
3NCHAC913CA 14.3 10.6 18 000 30 000
65
3NCHAC013C 25.7 17.5 18 000 30 000
100 18
3NCHAC013CA 25.2 17.1 17 000 28 000
3NCHAC914C 20.3 14.7 18 000 29 000
100 16
3NCHAC914CA 19.9 14.4 16 000 28 000
70
3NCHAC014C 32.4 21.9 17 000 28 000
110 20
3NCHAC014CA 31.7 21.4 16 000 26 000
3NCHAC915C 20.7 15.5 17 000 28 000
105 16
3NCHAC915CA 20.2 15.1 16 000 26 000
75
3NCHAC015C 33.3 23.2 16 000 26 000
115 20
3NCHAC015CA 32.6 22.7 15 000 25 000
3NCHAC916C 21.1 16.2 16 000 26 000
110 16
3NCHAC916CA 20.6 15.8 15 000 25 000
80
3NCHAC016C 40.6 28.1 14 000 23 000
125 22
3NCHAC016CA 39.7 27.5 13 000 22 000
3NCHAC917C 27.4 20.6 14 000 23 000
120 18
3NCHAC917CA 26.7 20.1 13 000 22 000
85
3NCHAC017C 41.7 29.8 13 000 22 000
130 22
3NCHAC017CA 40.8 29.2 12 000 21 000
3NCHAC918C 27.9 21.6 13 000 22 000
125 18
3NCHAC918CA 27.3 21.1 12 000 21 000
90
3NCHAC018C 49.6 35.2 12 000 21 000
140 24
3NCHAC018CA 48.5 34.4 12 000 19 000
3NCHAC919C 28.5 22.6 13 000 21 000
130 18
3NCHAC919CA 27.8 22.1 12 000 20 000
95
3NCHAC019C 50.9 37.3 12 000 19 000
145 24
3NCHAC019CA 49.8 36.5 11 000 18 000

14
 BALL BEARING SERIES

Dimension table
B
Type C
Ceramic balls

φD φd

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Grease lub. Oil-and-air lub.
3NCHAC920C 39.0 29.7 12 000 20 000
140 20
3NCHAC920CA 38.1 29.0 11 000 19 000
100
3NCHAC020C 52.4 39.3 11 000 19 000
150 24
3NCHAC020CA 51.2 38.4 11 000 18 000
3NCHAC921C 39.9 31.2 11 000 19 000
145 20
3NCHAC921CA 38.9 30.5 11 000 18 000
105
3NCHAC021C 61.0 45.6 11 000 18 000
160 26
3NCHAC021CA 59.6 44.6 9 900 17 000
3NCHAC922C 40.7 32.7 11 000 18 000
150 20
3NCHAC922CA 39.8 31.9 10 000 17 000
110
3NCHAC022C 69.9 51.6 9 500 17 000
170 28
3NCHAC022CA 68.4 50.4 10 000 16 000
3NCHAC924C 50.5 41.2 10 000 17 000
165 22
3NCHAC924CA 49.3 40.3 9 300 16 000
120
3NCHAC024C 74.0 57.5 9 500 16 000
180 28
3NCHAC024CA 72.3 56.2 8 900 15 000
3NCHAC926C 61.2 50.8 9 200 15 000
180 24
3NCHAC926CA 59.8 49.6 8 600 14 000
130
3NCHAC026C 89.7 69.7 8 600 14 000
200 33
3NCHAC026CA 87.7 68.2 8 100 14 000
3NCHAC928C 62.3 53.2 8 600 14 000
190 24
3NCHAC928CA 60.8 52.0 8 100 14 000
140
3NCHAC028C 91.9 73.8 8 100 14 000
210 33
3NCHAC028CA 89.8 72.1 7 600 13 000
3NCHAC930C 83.2 69.8 7 500 12 000
210 28
3NCHAC930CA 81.3 68.2 7 000 12 000
150
3NCHAC030C 105 85.7 7 100 12 000
225 35
3NCHAC030CA 103 83.7 6 700 11 000
3NCHAC932C 84.8 73.3 7 100 12 000
220 28
3NCHAC932CA 82.8 71.6 6 600 11 000
160
3NCHAC032C 119 98.1 6 700 11 000
240 38
3NCHAC032CA 116 95.9 6 300 11 000
3NCHAC934C 86.4 76.7 6 700 11 000
230 28
3NCHAC934CA 84.3 74.9 6 300 11 000
170
3NCHAC034C 142 119 6 300 10 000
260 42
3NCHAC034CA 139 117 5 900 9 800

15
BALL BEARING SERIES

Dimension table
B
Type D
Ceramic balls

These bearings are useful only with oil and air lubrication.
Please use with lubricating spacers as shown below.
φD φd For spacer dimensions and nozzle locations, consult JTEKT.
Oil Oil Oil Oil
supply discharge supply supply

Lubricating spaceres Lubricating spaceres

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Oil-and-air lub.

35 62 14 3NCHAD007CA 9.05 5.40 52 000

40 68 15 3NCHAD008CA 9.50 6.05 46 000

45 75 16 3NCHAD009CA 10.6 6.95 42 000

50 80 16 3NCHAD010CA 11.1 7.65 38 000

55 90 18 3NCHAD011CA 13.7 9.70 34 000

60 95 18 3NCHAD012CA 14.3 10.6 32 000

65 100 18 3NCHAD013CA 14.9 11.5 30 000

70 110 20 3NCHAD014CA 20.2 15.1 28 000

75 115 20 3NCHAD015CA 20.6 15.8 26 000

80 125 22 3NCHAD016CA 24.1 18.8 23 000

85 130 22 3NCHAD017CA 24.5 19.6 22 000

90 140 24 3NCHAD018CA 32.0 25.5 21 000

95 145 24 3NCHAD019CA 32.6 26.6 20 000

100 150 24 3NCHAD020CA 33.2 27.7 19 000

105 160 26 3NCHAD021CA 37.6 31.8 18 000

110 170 28 3NCHAD022CA 42.4 36.1 17 000

120 180 28 3NCHAD024CA 43.8 39.0 16 000

130 200 33 3NCHAD026CA 55.0 47.2 14 000

16
 BALL BEARING SERIES

Dimension table
B
Type F
Ceramic balls

These bearings are useful only with oil and air lubrication.
Please use with lubricating spacers as shown below.
φD φd For spacer dimensions and nozzle locations, consult JTEKT.
Oil Oil Oil Oil Oil Oil Oil
supply supply discharge supply supply supply supply

Lubricating spaceres Lubricating spaceres

Boundary dimensions Basic load ratings Limiting speeds

mm Bearing numbers kN min-1
d D B Oil-and-air lub.

30 55 13 3NCHAF006CA 7.55 3.95 85 000

35 62 14 3NCHAF007CA 8.15 4.60 74 000
62 12 3NCHAF908CA 6.05 3.80 71 000
40
68 15 3NCHAF008CA 8.65 5.20 67 000
68 12 3NCHAF909CA 6.50 4.35 64 000
45
75 16 3NCHAF009CA 10.0 6.35 60 000
72 12 3NCHAF910CA 8.40 5.65 58 000
50
80 16 3NCHAF010CA 10.5 7.00 56 000
80 13 3NCHAF911CA 9.00 6.45 53 000
55
90 18 3NCHAF011CA 12.6 8.45 50 000
85 13 3NCHAF912CA 9.10 6.75 49 000
60
95 18 3NCHAF012CA 13.3 9.30 47 000
90 13 3NCHAF913CA 10.3 7.75 46 000
65
100 18 3NCHAF013CA 13.9 10.2 44 000
100 16 3NCHAF914CA 11.8 9.20 42 000
70
110 20 3NCHAF014CA 18.7 13.2 40 000
105 16 3NCHAF915CA 12.2 9.90 40 000
75
115 20 3NCHAF015CA 19.1 13.9 38 000
110 16 3NCHAF916CA 12.6 10.6 38 000
80
125 22 3NCHAF016CA 22.4 16.5 35 000
120 18 3NCHAF917CA 15.1 12.5 35 000
85
130 22 3NCHAF017CA 22.8 17.4 32 000
125 18 3NCHAF918CA 15.6 13.4 32 000
90
140 24 3NCHAF018CA 28.8 21.4 30 000
130 18 3NCHAF919CA 15.6 13.4 30 000
95
145 24 3NCHAF019CA 29.5 22.5 29 000
140 20 3NCHAF920CA 15.7 13.9 29 000
100
150 24 3NCHAF020CA 30.1 23.6 27 000
145 20 3NCHAF921CA 22.3 19.3 27 000
105
160 26 3NCHAF021CA 34.2 27.1 26 000
150 20 3NCHAF922CA 23.0 20.6 26 000
110
170 28 3NCHAF022CA 37.4 29.5 25 000
165 22 3NCHAF924CA 23.3 21.3 24 000
120
180 28 3NCHAF024CA 43.0 37.6 23 000
180 24 3NCHAF926CA 27.3 25.4 22 000
130
200 33 3NCHAF026CA 53.8 45.3 21 000

17
 GLOBAL NETWORK
BEARING BUSINESS OPERATIONS

JTEKT CORPORATION NAGOYA HEAD OFFICE KOYO KOREA CO., LTD.

No.1-1, Asahimachi, Kariya, Aichi 448-8652, JAPAN Inwoo Building 6F, 539-11, Shinsa-Dong,
(move to Midland Square at Meieki 4-chome, Nakamura-ku, Kangnam-Ku, Seoul, KOREA
Nagoya, is planned for Oct. 2006) TEL : 82-2-549-7922
TEL : 81-566-25-5111 FAX : 82-2-549-7923
FAX : 81-566-25-5470
JTEKT CORPORATION BEIJING LIAISON OFFICE
JTEKT CORPORATION OSAKA HEAD OFFICE Room 1108 Tower-B Winterless-Center, No.1 Xidawang-Road,
Sales & Marketing Headquarters Chaoyang-District, Beijing, CHINA
No.5-8, Minamisemba 3-chome, Chuo-ku, Osaka 542-8502, JAPAN TEL : 86-10-6538-8070
TEL : 81-6-6245-6087 FAX : 86-10-6538-8077
FAX : 81-6-6244-9007
KOYO (SHANGHAI) CO., LTD.
Rm.1905, Aetna Tower, 107 Zunyi Road, Shanghai 200051, CHINA
TEL : 86-21-6237-5280
OFFICES FAX : 86-21-6237-5277

KOYO CANADA INC. JTEKT CORPORATION SHANGHAI LIAISON OFFICE

5324 South Service Road, Burlington, Ontario L7L 5H5, CANADA Rm.1907, Aetna Tower, 107 Zunyi Road, Shanghai 200051, CHINA
TEL : 1-905-681-1121 TEL : 86-21-6237-5280
FAX : 1-905-681-1392 FAX : 86-21-6237-5277

KOYO CORPORATION OF U.S.A. KOYO AUSTRALIA PTY. LTD.

-Cleveland Office- Unit 7, 175-179 James Ruse Drive, Rosehill, N.S.W. 2142 , AUSTRALIA
29570 Clemens Road, P.O.Box 45028 Westlake, TEL : 61-2-9638-2355
OH 44145, U.S.A. FAX : 61-2-9638-3368
TEL : 1-440-835-1000
FAX : 1-440-835-9347 JTEKT CORPORATION EUROPEAN BEARING CENTRAL OFFICE
-Detroit Office- Markerkant 13-01, 1314 AN Almere, THE NETHERLANDS
47771 Halyard Drive, Plymouth, MI 48170, U.S.A. TEL : 31-36-5383333
TEL : 1-734-454-1500 FAX : 31-36-5347212
FAX : 1-734-454-4076
KOYO KULLAGER SCANDINAVIA A.B.
KOYO MÉXICANA, S.A. DE C.V. Johanneslundsvagen 4 194 61 Upplands Väsby, SWEDEN
Rio Nazas No.171, 3er piso, Col. Cuauhtemoc, México, D.F. C.P. TEL : 46-8-594-212-10
06500, MÉXICO FAX : 46-8-594-212-29
TEL : 52-55-5207-3860
FAX : 52-55-5207-3873 KOYO (U.K.) LTD.
Whitehall Avenue, Kingston, Milton Keynes MK10 OAX,
KOYO LATIN AMERICA, S.A. UNITED KINGDOM
Edificio Banco del Pacifico Planta Baja, Calle Aquilino de la TEL : 44-1908-289300
Guardia y Calle 52, Panama, REPUBLICA DE PANAMA FAX : 44-1908-289333
TEL : 507-208-5900
FAX : 507-264-2782/507-269-7578 EUROPA-KOYO B.V.
Lekdijk 187, 2967 GJ Langerak, THE NETHERLANDS
KOYO ROLAMENTOS DO BRASIL LTDA. TEL : 31-184-606800
Rua Desembargador Eliseu Ghilherme 304, 7-Andar, FAX : 31-184-602572/606857
Paraiso CEP 04004-30, BRASIL
TEL : 55-11-3887-9173 KOYO ROMANIA REPRESENTATIVE OFFICE
FAX : 55-11-3887-3039 Str. Frederic Jolliot-Curie, Nr.3, Etaj 1, Ap.2, Sector 5
Bucharest, ROMANIA
JTEKT (THAILAND) Co., LTD. TEL : 40-21-410-4170/4182/0984
172 Moo 12 Tambol Bangwua, Amphur Bangpakong, FAX : 40-21-410-1178
Chachoengsao 24180, THAILAND
TEL : 66-38-533-310-7 KOYO DEUTSCHLAND GMBH.
FAX : 66-38-532-776 Bargkoppelweg 4, D-22145 Hamburg, GERMANY
TEL : 49-40-67-9090-0
KOYO SINGAPORE BEARING (PTE.) LTD. FAX : 49-40-67-9203-0
38 Tuas West Road, Singapore 638385, SINGAPORE
TEL : 65-6274-2200 KOYO FRANCE S.A.
FAX : 65-6862-1623 8 Rue Guy Moquet, B.P.189 Z.I., 95105 Argenteuil Cedex, FRANCE
-India Office- TEL : 33-1-3998-4202
1104, GD-ITL Tower, B-08, NETAJI SUBHASH PLACE, PITAM FAX : 33-1-3998-4244/4249
PURA, DELHI 110034 INDIA
TEL : 91-11-2735-3502Å`04 KOYO IBERICA, S.A.
91-11-5537-4803Å`04 Avda.da la Industria, 52-2 izda 28820
FAX : 91-11-2715-3501 Coslada Madrid, SPAIN
TEL : 34-91-329-0818
PHILIPPINE KOYO BEARING CORPORATION FAX : 34-91-747-1194
Rm.504, Comfoods Bldg., Cor. Gil Puyat Ave. and
Pasong Tamo, Makati City, PHILIPPINES KOYO ITALIA S.R.L.
TEL : 63-2-817-8881/8901 Via Bronzino 9, 20133 Milano, ITALY
FAX : 63-2-867-3148 TEL : 39-02-2951-0844
FAX : 39-02-2951-0954

The contents of this catalog are subject to change whithout prior notice.
Every possible effort has been made to ensure that the data listed in this catalog is correct.
However, we can not assume responsibility for any errors or omissions.
 BALL BEARING SERIES
Angular Contact Ball Bearings for Machining Tools

CAT.NO. B2006E
, ,
Printed in Japan 06.3-1CM( 02.5)