Scribd Logo
Upload

Welcome to Scribd!

  • 231 views

    Flange Leakage Check

    Uploaded by

    Ankith
    This document provides steps to perform a flange leakage check in Caesar II using the ASME Section VIII method. The key steps are: 1) After static analysis, click "Flanges" under "Analysis" to input flange parameters such as type, class, grade and dimensions according to applicable codes. 2) Input bolt and gasket parameters from codes such as ASME B16.20 including number of bolts, diameter, material properties. 3) Input design pressure, axial force and bending moment from static analysis. 4) Run the analysis and check the safety factor - a value less than one indicates joint failure. Address failures by reducing loads or increasing flange rating.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Flange Leakage Check

    Uploaded by

    Ankith
    231 views6 pages
    This document provides steps to perform a flange leakage check in Caesar II using the ASME Section VIII method. The key steps are: 1) After static analysis, click "Flanges" under "Analysis" to input flange parameters such as type, class, grade and dimensions according to applicable codes. 2) Input bolt and gasket parameters from codes such as ASME B16.20 including number of bolts, diameter, material properties. 3) Input design pressure, axial force and bending moment from static analysis. 4) Run the analysis and check the safety factor - a value less than one indicates joint failure. Address failures by reducing loads or increasing flange rating.

    Original Description:

    Flange leakage check

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides steps to perform a flange leakage check in Caesar II using the ASME Section VIII method. The key steps are: 1) After static analysis, click "Flanges" under "Analysis" to input flange parameters such as type, class, grade and dimensions according to applicable codes. 2) Input bolt and gasket parameters from codes such as ASME B16.20 including number of bolts, diameter, material properties. 3) Input design pressure, axial force and bending moment from static analysis. 4) Run the analysis and check the safety factor - a value less than one indicates joint failure. Address failures by reducing loads or increasing flange rating.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    231 views6 pages

    Flange Leakage Check

    Uploaded by

    Ankith
    This document provides steps to perform a flange leakage check in Caesar II using the ASME Section VIII method. The key steps are: 1) After static analysis, click "Flanges" under "Analysis" to input flange parameters such as type, class, grade and dimensions according to applicable codes. 2) Input bolt and gasket parameters from codes such as ASME B16.20 including number of bolts, diameter, material properties. 3) Input design pressure, axial force and bending moment from static analysis. 4) Run the analysis and check the safety factor - a value less than one indicates joint failure. Address failures by reducing loads or increasing flange rating.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 6

    Flange Leakage checking in Caesar II using ASME Section

    VIII method
    My last two articles on flange leakage explains the basic theory behind flange leakage checking and
    methods for performingflange leakage checking using pressure equivalent method. In this article I will
    explain the steps taken to perform flange leakage check using Caesar II by ASME Sec VIII method.
    Normally this method is performed when the analysis in pressure equivalent method shows failure in
    Caesar II. Pressure equivalent method being too conservative does not provide us the actual realistic
    results. Hence this method is widely accepted where pressure equivalent method shows a failure. The
    steps involved are mentioned below:

     After performing static analysis click the “Analysis” and then click “Flanges” in CAESAR II as
    shown below.

     Provide a file name and select the proper Flange Type in the section as mentioned in the PMS.
    Input the flange parameters as shown below:
     Press the key “Ctrl+F” to select the concerning Size and Rating. Few data will automatically filled
    from Caesar II database. However it is good practise to confirm the data from governing code.
     Flange Class is the flange pressure rating and is required for checking P-T Rating of Equivalent
    Pressure.
     Flange Grade: Select Material Group No. as per ASME B 16.5 Table 1A list of material
    specification. Following table can be used as reference:

     Refer to the applicable flange code ASME 16.5 or ASME B 16.47 and update automatically filled
    flange data. Take special care while inputing for ‘Small End Hub Thickness’& ‘Large End Hub
    Thickness’. ‘Small End Hub Thickness ’ must be equal to the Pipe Thickness. Large End Hub
    Thickness must be equal to (X-B) where X is Hub Diameter and B Flange ID.
     Enter hub Length h=(Y-tf) where Y is length through Hub and tf is flange thickness.
     Now it is the turn to enter the Bolts and gasket parameters. Take parameters from ASME B 16.20
    or ASME B 16.21 as shown below:

     Check Bolt Circle Diameter, Number of Bolts and Bolt Diameter, suggested by CAESAR II in
    reference with ASME B 16.47, 16.5.
     Correctly input for Gasket information in conjunction with ASME B 16.20 or 16.21 as applicable.

    For Effective Gasket Modulus, press Shift+? Key and then follow “High End” in Help statement. Leak
    Pressure Ratio m, Gasket Seating Stress y shall be in accordance with ASME SECTION VIII Div.1.
    Values for Caesar II help can be taken by pressing Shift+?.

     For Nubbin Width in the right side, Leave blank for Welding Neck Type and input Ring joint width
    as per the ring no. as described on ASME B 16.20 Table 3 TYPE R RING GASKET
    DIMENSIONS AND TOLERANCES for ring type joint.
     Facing Sketch/ Facing Column can be inputted as follows mentioned below:
     Now input the material data as shown below:

     Select the material of Flange and bolt, and Input design temperature.

     Flange Allowable & Bolt Allowable at design and ambient temp can be taken from CAESAR II
    database for particular flange and bolt material.

    Flange Modulus of Elasticity shall be taken from table C-6 of ASME B-31.3.which is given in millions of psi
    convert it to consistent unit

     Use 1.0 for Flange Allowable Stress Multiplier and 2.0 for Bolt Allowable Stress Multiplier. Use
    project specific data if available.
     Now Input Design Pressure, Axial Force, Bending Moment from Static analysis of the Caesar file
    as shown below:
     Now run the analysis to study the output results. Normally If safety Factor is less than one then
    joint failure is predicted and in output this is shown by a * mark.
     If result shows failure then try to reduce the bending moment or axial force and reanalyse. If that
    is not possible check if the flange rating can be increased.

    You might also like