Scribd Logo
Upload

Welcome to Scribd!

  • 248 views

    EMV Card Reader Upgrade Kit Instructions - 05162016

    Uploaded by

    Shashi K Kumar
    This document provides instructions for upgrading an ATM to support EMV chip card readers, including installing new hardware and software. The software upgrade requires inserting a USB drive with the correct software version and selecting software update in the operator menu. For the hardware upgrade, the existing card reader is removed and a new EMV reader installed. Additional steps enable the EMV functionality in the device settings menus.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    EMV Card Reader Upgrade Kit Instructions - 05162016

    Uploaded by

    Shashi K Kumar
    248 views6 pages
    This document provides instructions for upgrading an ATM to support EMV chip card readers, including installing new hardware and software. The software upgrade requires inserting a USB drive with the correct software version and selecting software update in the operator menu. For the hardware upgrade, the existing card reader is removed and a new EMV reader installed. Additional steps enable the EMV functionality in the device settings menus.

    Original Description:

    Hyosung

    Original Title

    EMV Card Reader Upgrade Kit Instructions_05162016

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for upgrading an ATM to support EMV chip card readers, including installing new hardware and software. The software upgrade requires inserting a USB drive with the correct software version and selecting software update in the operator menu. For the hardware upgrade, the existing card reader is removed and a new EMV reader installed. Additional steps enable the EMV functionality in the device settings menus.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    248 views6 pages

    EMV Card Reader Upgrade Kit Instructions - 05162016

    Uploaded by

    Shashi K Kumar
    This document provides instructions for upgrading an ATM to support EMV chip card readers, including installing new hardware and software. The software upgrade requires inserting a USB drive with the correct software version and selecting software update in the operator menu. For the hardware upgrade, the existing card reader is removed and a new EMV reader installed. Additional steps enable the EMV functionality in the device settings menus.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    Nautilus Hyosung EMV Card Reader

    Hardware & Software Upgrade Instructions


    Updating Software to New Release Supporting EMV
    Note: Minimum software versions that support EMV card readers:

    WinCE 5.0 (APV01.04.14) 1800CE/5000CE/5300CE


    WinCE 6.0 (APV6.01.05) 1800SE/2700/2700T/4000W/5000SE/2600(HALO)
    1. Insert USB device (with correct AP software) into the USB port (found on the mainboard for WinCE 5.0
    and I/O board for WinCE 6.0 models), log into Operator Function Menu and select System Setup.

    2. Select System Control.


    3. Select Software Update and confirm by selecting Yes.

    Nautilus Hyosung EMV Card Reader Hardware & Software Upgrade Instructions Page 2
    EMV Card Reader Hardware Upgrade Kit Installation
    1. Power down the ATM and locate the card reader cable on the I/O board and disconnect :
    CN31 on WinCE 6.0 / J14 on WinCE 5.0 (1800CE) / COM 1 on 5000CE/5300CE

    WinCE 5. 0

    WinCE 6.0

    2. Remove the 2 screws that hold the card 3. Remove the 4 screws that hold the card reader
    reader flicker board. bezel and remove card reader with bezel.

    Nautilus Hyosung EMV Card Reader Hardware & Software Upgrade Instructions Page 3
    4. Install new EMV card reader/bezel and replace the screws that hold the card reader and flicker board
    onto the bezel.
    a. Screw ground wire from EMV card reader to a grounded point on the ATM body.

    5. Connect Card reader cable to the I/O board ( see step1) and to the back of the card reader.
    CN31 on WinCE 6.0 / J14 on WinCE 5.0 (1800CE) / COM4 on 5000CE/5300CE

    Nautilus Hyosung EMV Card Reader Hardware & Software Upgrade Instructions Page 4
    EMV Card Reader Software Enabling Instructions
    To enable the EMV card reader
    (for either DIP or EMV transactions)
    1. Log into Operator Function Menu and select System Setup.

    2. Select Device Setup.

    3. Select NH EMV and confirm by selecting Yes.

    Nautilus Hyosung EMV Card Reader Hardware & Software Upgrade Instructions Page 5
    To enable the EMV card reader to do Chip Card transactions
    (this must be supported by your host processor)
    1. Select Customer Setup.

    2. Select Optional Function 1.

    3. Select EMV and Enable to begin processing EMV transactions.

    Note: Once EMV is enabled, all cards (magnetic stripe and EMV “chip” cards) will be held in the card reader
    at the start of the transaction. Non-EMV card (mag stripe) users will be asked if they want to
    proceed with the transaction and to remove their card so the magnetic stripe can be read. EMV card
    users will be prompted to remove their cards prior to receiving cash.

    Nautilus Hyosung EMV Card Reader Hardware & Software Upgrade Instructions Page 6

    You might also like