Tehnic Ventis Mx4

Multi-gas Monitor
Product Manual
Set-up
Operation
Service
Part Number: 17152357-1

Version 14 1
Ventis™ MX4 Product Manual
Contents
►Copyright Notice .........................................................................................................................................................4
►Warnings and Cautionary Statements ........................................................................................................................4
General...................................................................................................................................................... 4
Personnel .................................................................................................................................................. 4
Hazardous Conditions, Poisons, and Contaminants ................................................................................ 4
General Usage .......................................................................................................................................... 5
Agency-issued Conditions of Use and Warnings ...................................................................................... 5
Recommended Practices .......................................................................................................................... 6
►Ventis MX4 Resources ...............................................................................................................................................6
►Ventis MX4 Capabilities ..............................................................................................................................................7
►Unpacking the Monitor................................................................................................................................................7
Contents .................................................................................................................................................... 7
Hardware Features and Functions ............................................................................................................ 8
Display Screen .......................................................................................................................................... 9
Alarms ..................................................................................................................................................... 11
►Monitor Set-up .......................................................................................................................................................... 14
Batteries .................................................................................................................................................. 15
Docking Stations, Chargers, and other Accessories .............................................................................. 15
Battery Charging ..................................................................................................................................... 16
Power-on and -off .................................................................................................................................... 16
Configuration ........................................................................................................................................... 18
Instructions .............................................................................................................................................. 19
►Monitor Use and Service .......................................................................................................................................... 27
Zero, Calibration, and, Bump testing ...................................................................................................... 27
Recommendations .................................................................................................................................. 27
General information ................................................................................................................................. 28
Instructions .............................................................................................................................................. 28
Supplies................................................................................................................................................... 29
Remote Sampling .................................................................................................................................... 35
Cleaning .................................................................................................................................................. 36
Service .................................................................................................................................................... 36
Aspirated Monitor .................................................................................................................................... 37
Diffusion Monitor ..................................................................................................................................... 39
© 2017 Industrial Scientific Corporation 2

Sensor, Sensor Barrier, LCD, and vibrating motor replacement ............................................................ 40

Battery Configuration .............................................................................................................................. 45
►Products, Specifications, and Certifications........................................................................................................ 47
Ventis MX4 Accessories and Parts ......................................................................................................... 47

Monitor Specifications ............................................................................................................................. 47
Battery Specifications .............................................................................................................................. 48
Operating Conditions .............................................................................................................................. 48
Cold-weather Operation .......................................................................................................................... 48
Storage Conditions .................................................................................................................................. 48
Sensor Specifications .............................................................................................................................. 49
Toxic Gas Sensor Cross-sensitivity Table .............................................................................................. 49
LEL, and LEL Correlation Factors for Combustible Gases .............................................................. 50
Certifications ........................................................................................................................................... 51
►Warranty ............................................................................................................................................. 53
Limitation of Liability ................................................................................................................................ 53
Contact Information ...................................................................................................................................................... 54
3 © 2017 Industrial Scientific Corporation

►Copyright Notice
Ventis MX4™ and Ventis™ are trademarks of Industrial Scientific Corporation.
All trademarks and registered trademarks are the property of their respective owners.
These help materials or any part thereof may not, without the written consent of Industrial Scientific Corporation, be
copied, reprinted, or reproduced in any material form including but not limited to photocopying, transcribing,
transmitting, or storing it in any medium or translating it into any language, in any form or by any means, be it digitally,
electronic, mechanical, xerographic, optical, magnetic, or otherwise.
The information contained in this document is proprietary and confidential and all copyright, trademarks, trade names,
patents, and other intellectual property rights in the documentation are the exclusive property of Industrial Scientific
Corporation unless otherwise specified. The information (including but not limited to data, drawings, specification,
documentation, software listings, source or object code) shall not at any time be disclosed directly or indirectly to any
third party without prior written consent.
The information contained herein is believed to be accurate and reliable. Industrial Scientific Corporation accepts no
responsibility for its use by any means or in any way whatsoever. Industrial Scientific Corporation shall not be liable
for any expenses, costs by damage that may result from the use of the information contained within this document.
Although every effort is made to ensure accuracy, the specifications of this product and the content herein are subject
to change without notice.
►Warnings and Cautionary Statements
General
IMPORTANT
Failure to perform certain procedures or note certain conditions may impair the performance of this
product. For maximum safety and optimal performance, please read and understand the Ventis MX4
Product Manual available online at the Ventis MX4 Resource Center at
www.indsci.com/ VentisMX4resources.
Personnel
CAUTION: For safety reasons, this equipment must be operated and serviced by qualified personnel only.
Read and understand the product manual completely before operating or servicing.
Hazardous Conditions, Poisons, and Contaminants

WARNING: Servicing the unit, replacing or charging batteries, or using the communications port must only
be done in an area known to be nonhazardous. Not for use in oxygen-enriched atmospheres.
WARNING: Power-off the monitor before servicing the unit or replacing the battery.
WARNING: Substitution of components may impair intrinsic safety and may cause an unsafe condition.
CAUTION: High off-scale readings may indicate explosive gas concentration(s).
CAUTION: Any rapid up-scale reading followed by a declining or erratic reading may indicate gas
concentration(s) beyond the upper scale limit which may be hazardous.
Silicone compound vapors or other known contaminants may affect the combustible gas sensor and cause
readings of combustible gas to be lower than actual gas concentrations. If the monitor has been used in an

area where silicone vapors were present, always calibrate the monitor before next use to ensure accurate
measurements.
General Usage
Oxygen-deficient atmospheres may cause combustible gas readings to be lower than actual concentrations.
Oxygen-enriched atmospheres may cause combustible gas readings to be higher than actual
concentrations.
Sudden changes in atmospheric pressure may cause temporary fluctuations in the oxygen reading.
Verify the calibration of the combustible gas sensor after any incident where the combustible gas content has
caused the monitor to display an over-range condition.
Sensor openings, water barriers, and the pump inlet must be kept clean. Obstruction of the sensor openings
or pump inlet and/or contamination of the water barriers may cause readings to be lower than actual gas
concentrations.
To avoid the potential of liquid being pulled into the sample tubing and pump assembly, it is recommended
that Industrial Scientific filter (P/N 17027152) be used on the sample tubing when drawing samples using the
aspirated monitor.
WARNING: INSERT THE ALKALINE BATTERIES WITH THE CORRECT POSITIVE “+” AND NEGATIVE “-“
ORIENTATION. WARNING: The Ventis MX4 is only approved for use with AAA battery types Energizer
EN92 and Duracell MN2400. Do NOT mix battery types.
WARNING: The use of leather cases can produce inaccurate readings with diffusion (non-aspirated) gas
detection instruments for specific monitoring applications. Leather cases should be used ONLY as carrying
cases, and NOT for continuous monitoring, with diffusion instruments configured to measure gases other
than O2, CO, CO2, H2S, and combustible gases (LEL/CH4).
Agency-issued Conditions of Use and Warnings
Ensure all part-use restrictions (e.g., battery) meet any agency-mandated conditions of use.
Ensure all instrument-configurable settings (e.g., always-on setting) meet any agency-mandated conditions
of use. When using instrument-compatible Industrial Scientific docking stations, maintain mandated settings
through the software (e.g., iNet Control or Accessory Software) or by manually configuring the instrument
settings after docking.
The Ventis MX4 is CSA certified according to the Canadian Electrical Code for use in Class I, Division 1 and
Class I, Zone 1 Hazardous Locations within an ambient temperature range of Tamb: -20°C to +50°C. CSA
has assessed only the %LEL combustible gas detection portion of this instrument for performance according
to CSA Standard C22.2 No. 152. This is applicable only when the monitor is used in the diffusion mode and
has been calibrated to 50% LEL CH4, and when the monitor is used in the aspirated mode with an Extended
range lithium-ion battery and has been calibrated to 50% LEL CH4.
CAUTION: CSA C22.2 No. 152 requires before each day’s usage, sensitivity must be tested on a known
concentration of pentane or methane equivalent to 25% or 50% of full scale concentration. Accuracy must
be within -0% to +20% of actual concentration. Accuracy may be corrected by referring to the
zero/calibration section of the Product Manual.
The equipment complies with the standards IEC 60079-29-1 and EN 60079-29-1 for methane, propane, and
hexane with the following exception: as for the methane (mine) detector, the battery run time was verified to
be seven (7) hours rather than the eight (8) hours recommended by the standards, respectively.
MED-certified instruments may be used only when configured and maintained to disallow power-off when
the unit is in alarm.
The Mine Safety and Health Administration (MSHA) has approved the Ventis MX4 as a Permissible Multi-
Gas Monitor with the following warnings:

• MSHA approved for use with either the P/N 17134453-X2, 3.7 volt, Lithium-ion battery or P/N
17148313-2, 3.7 volt, lithium-ion Extended battery only. The battery pack is not user-replaceable. The
monitor battery and the lithium battery on the main PCB are technician replaceable only. Charge
rechargeable lithium-ion batteries with an ISC battery charger designed for use with this monitor in fresh
air locations only.
• The monitor is to be calibrated according to the procedures in the instruction manual only.
• The aspirated version of the Ventis MX4 is only approved for use with the Extended range battery only.
• The monitor must display methane in the percent-by-volume mode (0-5%) for compliance
determinations required by 30 CFR Part 75, subpart D.
SANS 1515-certified units may be used only as follows:

• Diffusion applications
• Configured and maintained to disallow power-off when the unit is in alarm
• The Methane alarms are set as follows: low alarm = 1%vol and high alarm =1.4%vol
• With approved Lithium-ion batteries (see Ventis MX4 Accessories and Parts in this manual).
Recommended Practices
Industrial Scientific Corporation recommends the monitor be fully charged (when equipped with a
rechargeable battery), configured, and calibrated before first time use. If the lithium-ion battery is deeply
discharged, it can take up to an hour for the instrument display to indicate that the battery is charging.
Monitors used infrequently should be fully charged every four months.
No part of the unit should be covered by any garment, part of a garment, or other item that would restrict the
flow of air to the sensors or impair the operator's access to the audible, visual, or vibration alarms.
Industrial Scientific Corporation recommends a full monitor calibration be performed monthly (at a minimum),
using a certified concentration(s) of Industrial Scientific calibration gas(es) to help ensure monitor accuracy.
Industrial Scientific Corporation recommends the monitor be zeroed and bump tested before each use with a
certified concentration(s) of Industrial Scientific calibration gas(es).
Battery contacts are exposed on batteries when they are removed from the monitor. Do not touch the battery
contacts and do not stack batteries on top of one another.
When reassembling the instrument or installing a battery pack, maintain ingress protection by tightening
each fastener to its stated torque value (see the “Ventis MX4 Monitor three-Dimensional Diagram” and its
key in this manual).
Contact your service representative immediately if you suspect that the Ventis MX4 is working abnormally.
►Ventis MX4 Resources
The Ventis MX4 Product Manual is the primary resource, within a full suite of learning tools, developed for the monitor
user. Its step-by-step “walk through” format covers everything from unpacking to set-up, operation, and service. All
Ventis MX4 users should read and understand the Product Manual prior to unpacking or using the monitor.
Ventis MX4 product-specific resources are part of the organization’s broader training line-up, featuring online training
modules and face-to-face classroom programs for technicians, operators, first responders, trainers, and distributors.
Courses combine theory with hands-on learning, and can be tailored to the customer’s unique requirements and gas
monitoring applications.
The organization’s customer and technical support call centers provide product and order information, how-to product
assistance, and guidance for in-depth technical applications. Its service centers offer comprehensive factory repair
and maintenance services.
Industrial Scientific Corporation provides a full suite of resources to aid customers in the competent and safe use of
its products and services. With 19 manufacturing, support, and service centers and hundreds of distributors
worldwide, Industrial Scientific serves the globe’s gas detection needs.

►Ventis MX4 Capabilities
The Ventis MX4 is a portable multi-gas monitor. Offered as a diffusion monitor, it detects and measures gas(es)
present in open space. To enable monitor use within confined space locations, the Ventis MX4 is also offered as an
aspirated monitor. A pump module and battery accessories enable the conversion of either monitor for dedicated use
in either confined or open spaces.
Based on the customer’s monitor order, up to four sensors are factory installed enabling the monitor to continuously
and simultaneously detect and measure the presence of up to four specific gases.
Sensor Number available per Gases Monitored

Category monitor
Oxygen 1 O2 (Oxygen) only

Combustible 1 Monitor can be configured for sensor to measure ONE of the following:
• LEL (Pentane)
• LEL (Methane)
• CH4 (0%-5%)
Toxic 2 Each sensor detects and measures only ONE of the following:
• CO (Carbon Monoxide)
• CO/H2 Low (Carbon Monoxide with low H2 interference)
• H2S (Hydrogen Sulfide)
• NO2 (Nitrogen Dioxide)
• SO2 (Sulfur Dioxide)
Equipped with a multi-mode (audible, visual, and vibration) and multi-level alarm system, the Ventis MX4 monitor is
capable of notifying its user of potentially hazardous gas concentrations.
The monitor performs continuous data logging at 10 second intervals. It can store approximately 90 days of data for a
four-sensor configuration. Its date- and time-stamped event log records and stores data for the following: 60 alarm
events, 30 error events, and 250 manually performed calibrations or bump tests. The memory, when full, overwrites
the oldest data as the newest readings and events are logged.
The Ventis MX4 monitor functions as an independent device to monitor the environment for hazardous gas
concentrations. It is compatible with products that charge, calibrate, bump test, read and record instrument data,
protect, and otherwise enable or enhance use of the monitor and its data. For a complete list of these products,
please refer to the manual section, Ventis MX4 Accessories and Parts.
►Unpacking the Monitor
Contents
The monitor box contains the following items including, when ordered, those marked optional. Each item ordered
should be accounted for in the unpacking process.
Quantity Item Notes
1 as ordered Ventis MX4 Portable Multi- The monitor type is indicated on the box label.
gas Monitor Options:
• Ventis MX4 Diffusion
• Ventis MX4 Aspirated
• Ventis MX4 Aspirated with Conversion Kit
1 Ventis MX4 Quick start guide Review for important safety information before using
the monitor.
1 installed as ordered Battery One of four battery types are factory installed as
indicated on the box label.

Quantity Item Notes
Options:
• Rechargeable Lithium-ion (Li-ion)
• Rechargeable Slim extended lithium-ion (Li-ion)
• Rechargeable Extended range lithium-ion (Li-ion)
• Replaceable Alkaline
1 as ordered Ventis Charger Universal power cord. AC charger products include
interchangeable plugs (US, UK, EU, and AUS).
0 or 1 Calibration Cup Diffusion – 1 included
Aspirated – 0 included
1 Calibration and Bump Test Diffusion – two feet of clear tubing
Tubing
0 or 1 In-field Sampling Tubing Diffusion – 0 included
Aspirated – Ten feet of black tubing
1 Final Inspection & Test Contains the following factory set* information:
Report • Monitor Set-up Date
• Monitor Part Number (P/N)
• Monitor Serial Number (S/N)
• For Each Sensor*:
• P/N
• S/N
• Type
• Location
• Alarm level values
• Span gas values
• Span reserve values
*Some factory set sensor values subject to user changes.
1 Warranty Card --
After unpacking, if any item is missing or appears to have been damaged, contact a local distributor of Industrial
Scientific products or Industrial Scientific Corporation (for contact information, please see the manual’s last page).
►Monitor Overview
Hardware Features and Functions
The monitor’s case top (front of monitor) has two main sections. As shown below, the upper section contains the
sensor ports. The lower section houses the user interface features, a LCD display screen and two buttons. Each
feature’s general functions are noted below. As shown, the diffusion and aspirated monitors differ with respect to the
location of the air intake mechanism and visual alarm indicators.
The instrument may be used in any orientation when clipped to the user or when used with a compatible carrying
case. Normal instrument orientation for measuring gas concentration is hand held with sensors and display facing the
operator.

Number Feature Functions

1 Visual alarm indicator Signals an alarm or warning; frequency varies by alarm level. Also used as a
confidence indicator.
2 Pump inlet (aspirated) Air intake; calibration and bump test gas intake.
Sensor ports (diffusion)
3 LCD display User interface; backlight flashes when monitor is in system, high, or low
alarm states.
4 Audible alarm ports On when monitor is in system, high, or low alarm states; frequency and tone
vary by alarm level. Also used for warnings and as confidence indicator.
5 On/Off/Mode button Used to power-on and power-off. Also used to bypass a process/step or
advance to a next screen in both gas monitoring and configuration modes.
Sets values in configuration mode.
6 Enter button Used to begin a process/step in a process. Edits values in configuration
mode.
7 IrDA interface Indicates infrared light data exchange in-progress.
8 Charging contacts Battery charging.
Display Screen
The Ventis MX4 Boot-up Screen, as shown below, serves to introduce all icons and the alpha-numeric items (e.g.,
8.8.8) that can appear on the display when the monitor is in use, docked, or charging. Each display item is stationary,
communicates unique information, and appears only when relevant to the task being performed.
A sample Gas Monitoring Screen is also shown below, next to the boot-up screen. This illustrates how the icons and
the alpha-numeric characters work together to communicate several points of information to the monitor user.

Boot-Up Screen Gas Monitoring Screen

All possible screen images. Sample screen in gas monitoring mode.
NOTE: Display screens featured throughout this manual include the “pump” icon.
Similar in appearance to a fan, it indicates an aspirated monitor is in use. For a
diffusion monitor, the pump icon does not appear on the display.
It is helpful to view the boot-up screen in sections. The top and bottom rows each contain icons. The main function of
the middle section, in gas monitoring mode, is to communicate gas concentration readings. Definitions for all icons,
gas name abbreviations, gas measurement units, and other indicators are provided below. Where applicable, display
variations are noted.
Top Row Icons Definition

Status: indicates no monitor or sensor faults.
Warning: indicates monitor or sensor fault.
Zero: communicates zero status (e.g., zero results, zero in-progress, etc.).
Gas Cylinder: communicates calibration related information (calibration due, calibration

apply gas, etc.).
Clock: indicates a process is in-progress.
Calendar: communicates overdue warnings for service items (calibration, bump testing,
etc.).
Alarm: indicates an alarm causing condition.
Low level audio alarm is on.
High level audio alarm is on.
Peak: displayed when peak detection values are viewed.
Alpha-numeric Definition
display values
Carbon Monoxide (CO)
Methane (CH4)
Sulfur Dioxide (SO2)
Lower Explosive Limit. Display variations:

“LEL” (English)
“LIE” (French)
“UEG” (German)
Oxygen (O2)
Nitrogen Dioxide (NO2)

Alpha-numeric Definition
display values
Hydrogen Sulfide (H2S)
CO H2/Low
Percentage Volume: O2 and CH4 measurement unit
Percentage unit for combustible gases; display variations:

“% LEL” (English)
“% LIE” (French)
“% UEG” (German)
Parts Per Million: H2S, CO, SO2 and NO2 measurement unit.
Over-range: for any sensor in over-range, indicates the measured gas concentration is
greater than the measurement range of the sensor. Display variations:
“Or” (English and German)
“Sup” (French)
Negative Over-range: for any sensor in negative over-range indicates the measured gas
concentration is less than the negative measurement range of the sensor. Display
variations:
“-Or” (English and German)
“InF” (French)
Bottom Row Icons Definition
Battery level indicator; display variations:
Empty battery icon with three dashes in place of each sensor reading = critical battery
warning
Flashing empty battery icon = low battery warning
1 black bar = < 33% charge remaining
2 black bars = 34% – 66% charge remaining
3 black bars = 67% – 100% charge remaining
Security Code: indicates code is set or to be entered.
Pump: shown anytime an aspirated monitor is in use.
Indicates IrDA communication is in-progress.
Short Term Exposure Limit: communicates STEL values. Display variations:

“STEL” ( English and German)
“VLE” (French)
Time Weighted Average: communicates TWA values. Display variations:
“TWA” (English and German)
“VME” (French)
Alarms
NOTICE
→ All monitor alarms and warnings should be taken seriously and responded to as stated in company safety
standards.
→ Once initiated, an alarm will remain on while the alarm condition is present. For gas-related alarms, once the
detected gas concentration changes, the alarm indicators will change to reflect any new condition such as
low-alarm gas, high-alarm gas, over-range gas, or no gas alarm.
→ When the latch alarm feature is enabled and the monitor goes into alarm, it will remain in alarm until the
alarm condition no longer exists and the monitor user presses the ENTER button for one second. This
applies only to gas-related alarms.

It is practical for the monitor user to be aware of the possible alarms prior to monitor set-up and use. The Ventis MX4
has four alarm and warning levels. A “system level” alarm generates the highest frequency tone and highest level
visual and vibration signals. It is used to indicate such events as a pump, critical battery failure, or sensor failure. The
“high” or “low” level audio alarms, in combination with visual and vibration indicators, turn on when gas concentration
readings are over-range, high, or low. The lowest level indicator is a warning with beep patterns to indicate service
needs (e.g., low battery or calibration due). The beep is also used as a confidence indicator when enabled.
Alarm types and their alarm generating conditions are described below.
Display Description
An over-range condition occurs when the gas
concentration value sensed is above the
sensor’s measuring range.
After any over-range alarm, the monitor should

be calibrated.
Over-range Alarm Screen
NOTES: The O2 and toxic sensor values
The “Or” message indicates which sensor(s) is reading an over- normally reset when the gas sensed reaches an
range condition(s). All other sensors show their current gas acceptable range.
concentration readings on a numeric display (left) or gas names
on a text display (right). The high level alarms turn on and the
alarm icon displays. If the LEL reads over-range, the alarm latches
and the LEL sensor is automatically turned off.
Press the enter button to turn on the LEL
sensor. This will turn off the alarm indicators.
After a warm-up period of approximately 30
seconds, an LEL reading will display. If the new
reading is an over-range or other alarm
condition, the alarm indicators will turn on.
A negative over-range condition occurs when
the gas concentration value sensed is less than
the sensor’s measuring range.
After any negative over-range alarm, the

monitor should be calibrated.
Negative Over-range Alarm Screen
The “-Or” message indicates which sensor is reading a negative
over-range condition. All other sensors display their current gas
concentration readings*. The high level alarms turn on and the
alarm icon displays.
A high alarm condition occurs when the
concentration of gas sensed reaches a level
greater than the monitor’s high alarm value
setting for a sensor(s).
High Alarm Screen

A flashing gas concentration value* indicates which sensor(s)
reading(s) is the cause for alarm. The high level alarms turn on
and the up arrow icon displays.
A low alarm condition occurs when the
concentration of gas sensed reaches the
monitor’s low alarm value setting for a
sensor(s).

Display Description
Low Alarm Screen
reading(s) is the cause for alarm. The low level alarms turn on
and the down arrow icon displays.
A TWA alarm occurs when the calculated time
weighted average reaches the monitor’s
hazardous value for the set time frame.
TWA Alarm Screen

and the TWA icon flashes.
The STEL alarm occurs when the short term
exposure value exceeds the acceptable limit.
STEL Alarm Screen

and the STEL icon flashes.
Alarm occurs when the monitor registers no
sensors installed.
No Sensor Installed Screen

The system level alarms turn on and the error icon displays.
Alarm occurs when any installed sensor’s data-
related operations fail and the sensor is not
operational.
Sensor Data Fail Screen

A flashing “F” indicates which sensor is the cause for alarm. The
audio alarm turns on and the error icon displays.
Error codes 4XX to 5XX (404 shown here)
indicate the monitor has detected a malfunction.
The unit is not operational and and should be
examined by a qualified technician or reported
to Industrial Scientific for service or repair
information.
Critical Error Screen

Display Description
Alarm occurs when, if attached, the pump is not
operating correctly. While in alarm, every ten
seconds the monitor attempts to restart the
pump. If unsuccessful, the monitor remains in
alarm.
Note: The nominal flow rate is >200 cc/m (.2

Pump Fault Alarm
LPM). A pump fault alarm will occur when
The system level alarms turn on and the error icon displays.
the flow is less than 200 cc/m +0, -25%.
Alarm occurs when the monitor’s battery
reaches a low level of charge or is nearing its
end of life.
Low Battery Warning Screen

A beep sounds every 60 seconds and the empty battery icon
flashes.
This alarm occurs when there is not enough
battery life remaining for continued operation.
The battery must be charged or replaced.
The instrument is NOT detecting gas at this
time.
Critical Battery Alarm
The empty battery icon indicates a battery life warning, while
three dashes display in place of each sensor reading. The high
alarm sounds for 10 minutes before powering off the monitor.
Alarm occurs when one or more sensors are
due for a bump test. If the monitor settings
permit, an in-field bump test may be performed
in an area known to be nonhazardous.
Bump Overdue Screen

A “b” indicates which sensor(s) is overdue for bump testing. Two
beeps sound every 30 seconds and the calendar and alarm icons
display.
Alarm occurs when one or more sensors are
due for calibration. If the monitor settings
permit, an in-field calibration can be performed
in an area known to be nonhazardous.
Calibration Due Alarm Screen

The gas value flashes for each sensor overdue for calibration.
Three beeps sound every 30 seconds and the calendar and
alarm icons display. The gas cylinder icon flashes.
* The numeric mode display shows gas concentration values; the text mode display shows gas type names in place of gas values.
►Monitor Set-up

Preparing the monitor for first time use is a “3-C” process: charge (if equipped with a lithium-ion battery), configure,
and calibrate. This manual section covers charging and configuration for set-up purposes and can be consulted for
ongoing instruction thereafter. Immediately following this section, calibration is covered in the manual section, Use
and Service.
Batteries
As shown below, the Lithium-ion and Slim extended lithium-ion batteries are compatible with the diffusion instrument
only. The Extended range battery can be installed for use with a diffusion or aspirated instrument. The battery's
orderable part numbers are supplied in Battery part numbers and options.
Battery Compatibility
Rechargeable Replaceable
(part number*) (part number*)
Lithium-ion battery Slim extended Extended range Alkaline battery
lithium-ion battery lithium-ion battery
(VTSB-1XY*) (VTSB-4XY*) (VTSB-2XY*) (VTSB-3XY*)
Cover Cover
Ventis MX4 diffusion Yes Yes Yes Yes
Ventis MX4 aspirated No No Yes (without cover) Yes (without cover)

*X indicates color and Y indicates approvals.
Docking Stations, Chargers, and other Accessories

Fully charge the monitor before first use. The lithium-ion equipped Ventis MX4 can be charged using any of the
products listed below.
Part Number Product

Docking Stations
18109327 DSX™ Docking Station for Ventis
Calibration Stations
18108631 V-Cal™ Calibration Station
18107664 V-Cal™ 6-Unit Calibration Station
Chargers
18108191 Ventis Single Unit Charger

18108209 Ventis Single Unit Charger / Datalink
18108650 Ventis 6-Unit Charger
18108651 Ventis Single Unit Automotive Charger, 12 VDC
18108652 Ventis Single Unit Truck-Mount Charger, 12 VDC, with Cigarette Adapter

Part Number Product

18108653 Ventis Single Unit Truck-Mount Charger, 12 VDC, Hard Wired
NOTE: The above products are all equipped with a yellow LED “presence” indicator. This LED confirms that the monitor is properly seated in the
cradle such that the monitor can charge; however, it is NOT intended to be used as a charging indicator. This LED indicator may go out intermittently
during normal charging functions and will not light if the unit is fully charged when placed in the cradle. Always refer to the monitor display’s battery
level indicator to confirm the battery charge level.
Battery Charging
Charger insert placement

If the charger includes an insert, adjust the insert’s position to ensure the battery contacts touch the charging
contacts.
Rear insert position

Forward insert position
Once the insert is placed

Lithium-ion battery Slim extended lithium-ion Extended range lithium- into the desired position, a
battery ion battery firm push down will secure
Insert side 1: forward Insert side 2: forward Insert side 1: Rear it in place.
position position position To prevent losing the
insert, keep it in the cradle
in the most often used
position.
NOTE: Do NOT touch the battery contacts located at the front of the charger as contaminants and damage will inhibit the
battery’s ability to charge.
Power-on and -off

To power-on the Ventis MX4, press ON/OFF/MODE and hold for three to five seconds. During the first ten to15
seconds the monitor is on, its firmware completes internal tests and the user sees or hears what is described and
shown below. Following this initialization phase, a countdown screen displays. During this 20-second countdown, the
monitor user can enter configuration mode to manually adjust monitor settings.

Display and Options Instructions

No user action required.
Visual Test Screen

Displays for up to five seconds as the monitor completes a sensor
and alarm check. Visual, vibration, and audio alarms turn on
briefly, then off.
Be sure the pump inlet is not blocked.
Pump Set-up Screen

Displays for five to seven seconds for an aspirated monitor. The
monitor checks for the presence of a pump. If present, the pump is
started and, if needed, adjusted for optimum flow.
Software Version Screen

The Software Version Screen message displays for five seconds.
Calibration Days Screen

When the up arrow (▲) is featured, the number of days displayed
for each sensor indicates when the next calibration is due. When
the down arrow (▼) is featured, the number of days displayed
indicates when the last calibration occurred.
To enter gas monitoring mode:

allow the countdown to complete and
advance to the Gas Monitoring Screen.
Proceed to the manual section, Monitor Use
and Service.
To enter configuration mode:

Countdown Screen
simultaneously press ON/OFF/MODE and
Displays the 20 second countdown, one second at a time, from 20
ENTER, hold for three seconds, and release.
to one. Options :
Enter gas monitoring mode
Enter configuration mode


Press ON/OFF/MODE, hold for the full five
second countdown to zero, and release to
power-off the monitor.
Power-Off Screen
The screen displays a five-second countdown accompanied by five
beeps and LED flashes.
Configuration
Introduction
Before first time use of the monitor, its settings should be reviewed and, if needed, be adjusted. Qualified safety
personnel should complete the following tasks.
• Review the monitor settings for compliance with company policy and any applicable regulations, laws, and
observed guidelines as issued by regulatory agencies and government or industry groups.
• Determine which settings, if any, require adjustment.
• Make the adjustments or supervise other qualified personnel in the process.
• When using instrument-compatible Industrial Scientific docking station software (e.g., iNet, Docking Station
Server Administrative Console [DSSAC], or Accessory Software), maintain the mandated settings through
the software or by manually configuring the instrument settings after docking.
Monitor settings should be reviewed regularly and adjusted as needed. The following settings are adjustable or
“configurable" for the Ventis MX4.
LEL Type
Calibration Mode Setting
Low Alarm Settings
High Alarm Settings
TWA Alarm Settings
TWA Interval Settings
STEL Alarm Setting
Calibration Gas Settings
Clock Settings
Date Settings
Display Mode Setting
Confidence Indicator (on/off)
Confidence Indicator (type)
Bump Test In-field
Bump Test Due Warning
Bump Test Time Set-point
Bump Test Percentage
Bump Test Response Time
Alarm Latch Set
Zero In-field
Calibration In-field
Calibration Due Alarm
Calibration Due Set-point
Security Code
Language Selection
Always-on Setting
Shutdown In Alarm Setting
Alarm on Dock Setting
The Ventis MX4 can be configured manually as instructed below. Any changes made take effect immediately upon
exiting the configuration mode.

Instructions
NOTICES
→ The configuration mode should be accessed only by safety personnel authorized to change monitor settings
based on company policy.
→ Read ALL requirements and instructions outlined below, including the screen-by-screen process description,
before beginning the configuration process.
The configuration mode can be entered during the 20-second countdown of the power-on process. During the
countdown, simultaneously press ON/OFF/MODE and ENTER, hold for three seconds, and release to enter
configuration mode. (While in the configuration mode, the same button presses cause the monitor to exit
configuration). Each configuration screen times out after 30 seconds and the monitor enters gas monitoring mode. To
re-enter the configuration mode, power-off the monitor, then power-on and repeat the entry process.
Throughout the configuration process, the main functions of the two buttons are as follows.
• The ENTER button is used to edit values. It is also used, where noted, to begin a process or a step in a
process.
• The ON/OFF/MODE button is used to set the value. Where noted, it is also used to bypass a process or
step in a process, or to advance to the next configuration screen.
The first screen to display in configuration mode depends on three things:

• security code setting,
• the presence or absence of the China MA feature,
• and the presence or absence of an LEL sensor.
If the security code setting is 000, the security feature is disabled and the Enter Security Code Screen does NOT
appear. If the security code is NOT 000, the security feature is enabled and the monitor displays the Enter
Security Code Screen.
The monitor next checks for the presence of a China MA mining feature. If this feature is operational, the monitor
displays the Zero Initiate Screen.
If the China MA mining feature is NOT operational, the monitor then checks for an installed LEL sensor. If
installed, the monitor displays the LEL Type Screen. If no LEL sensor is installed, the monitor displays the Zero
Initiate Screen.
Configuration Process
Press ENTER to edit the value, if needed; press repeatedly or hold
down to speed the increment pace to reach the valid security code.
Press ON/OFF/MODE to enter configuration mode and arrive at the
next applicable screen.
Enter Security Code Screen

The presence of this screen indicates an
enabled security feature.
Press ENTER to edit the value, if needed.
Press ON/OFF/MODE to set the value and advance to the Zero Initiate
Screen.
NOTE: If the LEL type is changed, the sensor goes into calibration fail mode. A full calibration
is required before the monitor can be used and is accessible from the next screen in the
configuration process, the Zero Initiate Screen. For complete calibration instructions,
LEL Type Set Screen proceed to the manual section, Zero, Calibration, and Bump Testing.
Options

LEL
CH4
Press ON/OFF/MODE to bypass the zero and calibration processes
and advance to one of two screens.
If the installed sensor set includes H2S and NO2, OR, SO2 and NO2, the
monitor is pre-set for standard calibration mode and the Low Alarm Set-
point Screen displays.
Zero Initiate Screen
For all others installed sensor combinations, the Calibration Mode
Options
Selection Screen displays.
Bypass zero and calibration process.
Begin zero and calibration process.
Press ENTER to begin the zero and calibration process. Proceed to the
manual section, Zero, Calibration, and Bump Testing.
The quick calibration option sets the monitor to calibrate all four sensors
simultaneously. The standard calibration option sets the monitor to
calibrate each sensor independently.

Press ON/OFF/MODE to set the value and advance to the Low Alarm
Calibration Mode Selection Set Screen.
Options
0 = Standard Calibration
1 = Quick Calibration
NOTE: The user can edit the values for four alarm types in configuration mode. The monitor presents these options
in the order shown below.
1. Low alarm
2. High alarm
3. TWA (if toxic sensors installed)
4. STEL (if toxic sensors installed)
For each alarm type (e.g., low alarm), the user can edit the alarm settings for each installed sensor, one sensor at
a time. The order in which the sensors are subject to change is as follows.
1. Toxic sensor 1
2. LEL sensor
3. Toxic sensor 2
4. O2 sensor
Press ON/OFF/MODE to bypass the low alarm value set process and
advance to the High Alarm Set-point Screen.
Press ENTER to begin the low alarm value set process.
On the display, the first sensor subject to change flashes.
Press ENTER to edit the value, if needed; press repeatedly or hold down
to speed the increment pace.
Low Alarm Set-point Screen Press ON/OFF/MODE to set the value.
Displays the existing low alarm value for
each installed sensor. If any one of the The next sensor subject to change flashes. Continue to use the ENTER
sensors is NOT installed, its position on and ON/OFF/MODE buttons, respectively, to edit and set each sensor’s
the display is blank. low alarm value.
After the alarm value is set for each installed sensor, press
ON/OFF/MODE to advance to the High Alarm Set-point Screen.

Press ON/OFF/MODE to bypass high alarm value set process and
advance to one of two screens as noted below.
Press ENTER to begin the high alarm value set process.
High Alarm Set-point Screen Press ON/OFF/MODE to set the value.
Displays the existing high alarm value
for each installed sensor. If any one of The next sensor subject to change flashes. Continue to use the ENTER
the sensors is not installed, its position and ON/OFF/MODE buttons, respectively, to edit and set each sensor’s
on the display is blank. high alarm value.
ON/OFF/MODE and advance to one of two screens.
If at least one toxic sensor is installed, the TWA Alarm Set Screen
displays.
If NO toxic sensors are installed, the Calibration Gas Set Screen

displays.
Press ON/OFF/MODE to bypass the TWA alarm value set process and
advance to the TWA Interval Set-point Screen.
Press ENTER to begin the TWA alarm value set process.
TWA Alarm Set-point Screen Press ON/OFF/MODE to set the value.
Displays the existing TWA values for the
toxic sensors installed. No other sensor The next sensor subject to change flashes. Continue to use the ENTER
readings appear. and ON/OFF/MODE buttons, respectively, to edit and set each alarm
value.
ON/OFF/MODE to advance to the TWA Interval Set Screen.
Press ON/OFF/MODE to set the value and advance to the STEL Alarm
Set-point Screen.
TWA Interval Set-point Screen

Displays the existing TWA interval.
The value can be set from one to 40
hours, in increments of one.

Press ON/OFF/MODE to bypass the STEL alarm value set process and
advance to the Calibration Gas Set Screen.
Press ENTER to begin the STEL alarm value set process.
STEL Alarm Set-point Screen Press ON/OFF/MODE to set the value.
Displays the existing STEL values for The next sensor subject to change flashes. Continue to use the ENTER
the toxic sensors installed. No other and ON/OFF/MODE buttons, respectively, to edit and set each sensor’s
sensor readings appear. STEL alarm value.
ON/OFF/MODE to advance to the Calibration Gas Set Screen.
Press ON/OFF/MODE to bypass the calibration gas set process and
advance to the Clock Set Screen.
Press ENTER to begin the calibration gas value set process.
Calibration Gas Set Screen Press ON/OFF/MODE to set the value.
Displays the existing calibration gas The next sensor subject to change flashes. Continue to use the ENTER
value for each installed sensor. and ON/OFF/MODE buttons, respectively, to edit and set each sensor’s
calibration gas value.
If any one of the sensors is not installed, After calibration gas value is set for each installed sensor, press
its position on the display is blank. ON/OFF/MODE to advance to the Clock Set Screen.
Press ON/OFF/MODE to bypass the clock set process and advance to
the Date Set Screen.
Press ENTER to begin the clock set process.
On the display, the first time value subject to change flashes.
Clock Set Screen Press ON/OFF/MODE to set the value.
Displays the existing time values using a
24-hour time format. The next value subject to change flashes. Use the ENTER and
ON/OFF/MODE buttons, respectively, to edit the value.
After all values are set, press ON/OFF/MODE and advance to the Date
Set Screen.
Press ON/OFF/MODE to bypass the date set process and advance to
the Display Mode Set Screen.
Press ENTER to begin the date set process
On the display, the first date value subject to change flashes.
to speed the increment pace. Press ON/OFF/MODE to set the value.
Date Set Screen
Displays the existing date. The value The next date value subject to change flashes. Continue to use the
displayed on the far left is the month ENTER and ON/OFF/MODE buttons, respectively, to edit and set each
and to its right the day. The year is value.
displayed beneath the day.
After all values are set, press ON/OFF/MODE and advance to the
Display Mode Set Screen.

The display mode selected determines whether the monitor user will see
a numeric or text display (including alarm displays) when the monitor is
in the gas monitoring mode.

Press ON/OFF/MODE to set the value and advance to the Confidence
Indicator Set Screen.
Display Mode Set Screen
Options
0 = Numeric Mode
1 = Text Mode
With an enabled confidence indicator, the monitor will emit a signal,
every 90 seconds in gas monitoring mode, to inform the user it is
operational.

Press ON/OFF/MODE to set the value and advance to one of two
Confidence Indicator On-Off Screen screens.
If the confidence indicator is enabled, the Confidence Indicator
Options
Type Set Screen displays.
0 = Disable/off
1 = Enable/on
If the confidence indicator is disabled, the Bump Test In-field
Option Screen displays.
Sets the type of signal that will be emitted by an enabled confidence
indicator.

Press ON/OFF/MODE to set the value and advance to the Bump Test
In-field Option Screen.
Confidence Indicator Type Set
Screen
Options
1 = audible chirp
2 = LED flash
3 = combination audible chirp and LED
flash
When enabled, permits all monitor users to bump test the monitor from
the gas monitoring mode.

screens.
Bump Test In-field Option Screen If Bump Test In-field is enabled, the Bump Due Warning Option
Screen displays.
Options
0 = Disable/off
If the Bump Test In-field is disabled, the Alarm Latch Set
1 = Enable/on
Screen displays.

When enabled, the monitor will sound two beeps every 30 seconds and
its display icons will indicate a bump test is due.

Time Set-point Screen.
Bump Due Warning Option Screen
Options
0 = Disable/off
1 = Enable/on
Sets the elapsed time allowed between bump tests.

down to speed the increment pace.
Percentage Requirement Screen.
Bump Test Time Set-point Screen
Value range: .5 days to 7.0 days
Value increment: .5 days
Sets the percentage of calibration gas the monitor expects to be
exposed to.

Response Time Screen.
Bump Test Percentage Requirement
Screen
Value range: 50% to 99%
Value increment: one percent
Sets the bump test response time period.

Press ON/OFF/MODE to set the value and advance to the Latch Alarm
Set Screen.
Bump Test Response Time Screen
Value range: 30 to 300 seconds
Value increment: five seconds
When enabled, if the monitor goes into any gas-related alarm, it will
remain in alarm until after the gas concentration is less than (or more
than for oxygen) the alarm set point, and the monitor user presses the
ENTER button for one second.

Latch Alarm Set Screen Press ON/OFF/MODE to set the value and advance to the Zero In-field
Options Screen.
0 = Normal mode
1 = Latching mode

When enabled, all monitor users are permitted to zero the monitor from

screens.
Zero In-field Screen If Zero In-field is enabled, the Calibration In-field Option screen displays.
Options
0 = Disable/off If Zero In-field is disabled, the Calibration Due Alarm screen displays.
1 = Enable/on
When enabled, all monitor users are permitted to calibrate the monitor
from the gas monitoring mode.

Press ON/OFF/MODE to set the value and advance to the Calibration
Due Alarm Option.
Calibration In-field Option Screen
Options
0 = Disable/off
1 = Enable/on
When enabled, the monitor will activate the calibration due alarm, in gas
monitoring mode, when any sensor is due for calibration. A flashing gas
cylinder and gas type will appear on the display and three beeps will
sound every 30 seconds.

Calibration Due Alarm Option Screen Press ON/OFF/MODE to set the value and advance to the Calibration
Options Due Set-point screen.
0 = Disable/off
1 = Enable/on
Sets the elapsed time allowed between calibrations.

Press ON/OFF/MODE to set the value and advance to the Calibration
Days Set Screen.
Calibration Due Set-point Screen

Value range: one to 365 days
Value increment: one day
Sets how the Calibration Days Screen will display in operation mode.
NOTE: The up arrow (▲) will be featured on-screen when the unit is set
to display the number of days before a sensor’s next calibration is due.
The down arrow (▼) will be featured when the unit is set to display the
number of days since the last calibration was performed. A value will be
displayed for each installed sensor.
Calibration Days Set Screen
Options
Press ON/OFF/MODE to set the value and advance to the Security
0 = display days since last calibration
Code Set Screen
1 = display days until next calibration

A security code value of 000 permits all monitor users to enter
configuration mode and gain access to change the monitor’s settings. A
value other than 000 will restrict access to the configuration mode; it will
also restrict access to the shutdown process for an instrument that is
configured for “always on”.
Security Code Set Screen down to speed the increment pace.
Valid values: 000 to 999. Press ON/OFF/MODE to set the value and advance to the Language
Increment value: one Selection Screen.
Allows the choice of display languages as applied to select screens.

Press ON/OFF/MODE to set the value and return to the LEL Type Set
Screen.
Language Selection Screen

Options
E = English
F = French
d = German
When enabled, the shutdown process is security-code protected only if
the security code is not equal to 000. If the code is set to anything other
than 000, the user will be prompted to enter the unit's security code to
complete the shutdown process.

Always-on Set Screen Press ON/OFF/MODE to set the value and advance to the next
configuration mode screen.
Options
0 = Disable/off
1 = Enable/on
Disallow or allow operator-activated shutdown when the unit is in alarm.

Press ON/OFF/MODE to set the value and advance to the next
Shutdown In Alarm Screen

Options
0 = Disallows shutdown
1 = Allows shutdown
Disable or enable alarm indicators when the unit is docked.

Press ON/OFF/MODE to set the value and advance to the next
Alarm on Dock Screen

Options
0 = Disable/off

1 = Enable/on
►Monitor Use and Service
Proper monitor use and service includes everything from bump testing and calibration to keeping the monitor clean,
proper air sampling, and the replacement of parts and components. Beginning with calibration and bump testing, the
following sections provide information and instruction on all use and service tasks.
Zero, Calibration, and, Bump testing

Gas detection instruments are potentially life-saving devices. When completed regularly, the procedures defined
below help to maintain proper instrument functionality and enhance operator safety.
Procedures
Configuration. The configuration process allows qualified personnel to review and adjust a unit's settings.
Bump Test (or "functional test"). Bump testing checks for sensor and alarm functionality. The installed sensors are
briefly exposed to expected concentrations of calibration gases that are greater than the sensors’ low alarm set
points. When one or more sensors “pass” the test, they are “functional” and the unit will alarm. Each sensor’s “pass”
or “fail” result is indicated on the unit’s display.
Note: a bump test does not measure for sensor accuracy (see “Calibration”).
Zero. Zeroing sets each installed sensor to recognize the ambient air as clean air. If the ambient air is not truly clean
air, any gasses that are present and relevant to the installed sensor types will be measured and displayed as zero.
Readings will be inaccurate until the unit is correctly zeroed in truly fresh air or with a zero air cylinder.
Calibration. All sensors gradually degrade over time. This diminishes a sensor's ability to measure gas concentrations
accurately; however, regular calibrations adjust the instrument to compensate for this decline in sensitivity. During
calibration, the installed sensors are exposed to expected concentrations of calibration gases and, when needed, the
instrument will self-adjust to ensure the accurate measurement and display of gas concentration values.
Note: When a sensor has degraded beyond an acceptable level, no further adjustment is possible and the sensor will no longer
pass calibration.
Peak Readings. The instrument stores the highest detected gas readings, the "peak readings" or "peaks". Bump
testing and calibration will often register new peak readings. Therefore, the clearing of the peak readings should
follow each calibration. The instrument operator may also wish to clear the peak readings after a bump test, before a
change in location, or after an alarm is addressed and cleared.
Note: The peak readings and the data log readings are stored independently of one another; therefore, clearing the peak reading
does not affect the data log. Powering the instrument off or changing its battery does not affect the peak reading. These checks and
balances help promote operator safety, and serve to contain the peak readings in a "black-box" manner. In the event of a gas-
related incident, this black-box record can be useful to the safety team or a prospective investigator.
Recommendations
Industrial Scientific Corporation (ISC) minimum frequency recommendations for each procedure are summarized in
the table below. These recommendations are based on field data, safe work procedures, industry best practices, and
regulatory standards to help ensure worker safety. Industrial Scientific is not responsible for setting safety practices
and policies. These policies may be affected by the directives and recommendations of regulatory groups,
environmental conditions, operating conditions, instrument use patterns and exposure to gas, and other factors.
Procedure ISC Recommended minimum frequency

Configuration Before first use and as needed thereafter.
Calibrationa Before first use and monthly thereafter.
Bump testb Prior to each day’s use.
a
Between regular calibrations, ISC also recommends a calibration be performed immediately following each of these incidences: the
unit falls, is dropped, or experiences another significant impact; is exposed to water; fails a bump test; or has been repeatedly

exposed to an over-range (positive or negative) gas concentration. A calibration is also recommended after the installation of a new
(or replacement) sensor.
b
If conditions do not permit daily testing, bump tests may be done less frequently based on company safety policy.
Note: The use of calibration gases not provided by ISC may void product warranties and limit potential liability claims.
General information
The zero, calibration, and bump testing tasks are in-field enabled or in-field disabled in the configuration process.
This permits or denies access to these functions from the gas monitoring mode. When any of these options is
enabled, it is accessible to all monitor users. In gas monitoring mode, a series of presses on the ON/OFF/MODE
button gives the user access to the following screens and processes in the order shown.
• Gas Monitoring Screen

• Days Since Calibration
• Zero Initiate (if in-field enabled)
o Calibration Apply Gas Screen (if in-field enabled)
• Bump Test Initiate (if in-field enabled)
• Peak Readings
• TWA Readings
• STEL Readings
The monitor is capable of performing two types of calibration, and this option is set in configuration mode. The
calibration type selected also determines the monitor’s bump test type. With a “quick” calibration, the monitor is set to
calibrate and bump test all installed sensors simultaneously. With a “standard” calibration setting, these tasks are
completed independently for each installed sensor in the order shown below.
1. Oxygen sensor*
2. Toxic sensor 1
3. LEL sensor
4. Toxic sensor 2
*If set to the default value of 20.9% or 21%, the Oxygen sensor calibrates during the zero process and toxic 1 is the first to calibrate in the
calibration process.
The Ventis MX4 monitor can be calibrated with any of the accessories listed.
• Calibration cup and/or tubing shipped with the monitor (see instructions below)
• V-Cal Calibration Station (consult the calibration station manual for instruction)
• DSX™ Docking Station for Ventis MX4 (consult the docking station manual for instruction)
Instructions
Calibration and Bump Testing with Calibration Cup and/or Tubing
Read all instructions before beginning: notices, supply check-list, gas cylinder preparation, and the complete screen-
by-screen walk-through of the zero, calibrate, and bump test processes. Each process is presented in the order in
which it is accessible from gas monitoring mode.
NOTICES
→ Industrial Scientific recommends that full monitor calibration be performed, using a known certified
concentration(s) of Industrial Scientific calibration gas(es), to prepare the monitor for first time use, and
monthly (at a minimum) thereafter, to help ensure monitor accuracy.
→ Industrial Scientific also recommends that each monitor be zeroed and bump tested before each use with a
known certified concentration(s) of Industrial Scientific calibration gas(es).
→ Read ALL requirements and instructions outlined below, including the screen-by-screen process description,
before beginning the zero, calibration, or bump testing processes.
→ Only qualified personnel should zero, calibrate, or bump test a monitor.
→ Zero, calibration, and bump testing functions should be performed in a fresh air environment known to be
nonhazardous.
→ After calibration or bump testing, or after terminating either process, stop the flow of gas.

Supplies
Item Monitor/Regulator**
Aspirated monitor Aspirated monitor Diffusion monitor
with Demand Flow with Positive Flow with Positive Flow
Regulator** Regulator** Regulator**
Calibration cup* No No Yes
Calibration tubing 2 feet in length* Yes No Yes
Calibration tubing 2 feet in length with No Yes No
integrated “t” fitting
Calibration gas cylinder Yes Yes Yes
*Shipped with monitor.

**Industrial Scientific recommends 1) the use of positive flow regulators with a flow rate of .5 LPM, and 2) the diffusion monitor be calibrated or bump
tested using a positive flow regulator, NOT a demand flow regulator.
Diffusion monitor with positive flow regulator. Aspirated monitor with demand flow regulator.
Prepare the gas cylinder for use

• According to the supply chart above, attach the correct regulator to the gas cylinder and turn clockwise to tighten.
• Next, choose instruction A., B., or C. based on the monitor/regulator combination in use.
A. Aspirated with demand flow regulator

Attach either end of the tubing to the cylinder’s nipple.
DO NOT ATTACH THE OTHER END OF THE TUBING TO THE MONITOR BEFORE REACHING THE
“APPLY GAS SCREEN”. Completing the connection of the tubing will cause gas to flow. If gas is
applied before reaching the appropriate screen, the monitor will go into alarm and a failure will be
logged.
B. Aspirated with positive flow regulator
The calibration tubing with the t-fitting (not included) has two different sized openings, a narrow opening
at one end and a wider opening at the other end.
Attach the wider opening to the nipple on the cylinder’s regulator.
Attach the smaller opening to the pump inlet.
DO NOT APPLY THE GAS BEFORE REACHING THE “APPLY GAS SCREEN”. If gas is applied before
that point, the monitor will go into alarm and a failure will be logged.

C. Diffusion with positive flow regulator

Attach either end of the tubing to the cylinder’s nipple.
Attach the other end of the tubing to the calibration cup’s nipple.
DO NOT ATTACH THE CALIBRATION CUP TO THE MONITOR OR APPLY THE GAS BEFORE
REACHING THE “APPLY GAS SCREEN”. If gas is applied before that point, the monitor will go into
alarm and a failure will be logged.
Zero and Quick Calibration Process

Press ON/OFF/MODE to advance to the Days since
Calibration Screen.
Gas Monitoring Screen

Numeric mode display (left)
Text mode display (right)
Displays the gas concentration readings (or gas names
in text mode) for all installed sensors. If a sensor is NOT
installed, its position on the LCD is blank.
Press ON/OFF/MODE to advance to one of three
screens.
If zero in-field is enabled, the user advances to the Zero
Initiate Screen.
If zero in-field is disabled and bump test in-field is
enabled, the user advances to the Bump Test Initiate
Days Since Calibration Screen Screen.
Displays the number of days since the last successful
If zero in-field and bump test in-field are both disabled,
calibration for each installed sensor. Each value can be
the user advances to the Peak Readings Screen.
different.
NOTE: When zero, calibration, and bump test are ALL in-field enabled, and the user has entered zero from the gas
monitoring mode, the monitor expects to be calibrated following a successful zero.
If the desired task, after zero, is bump testing (or clearing the peaks) and NOT calibration, follow the instructions at
the Calibration Apply Gas Screen to terminate calibration.
Press ENTER to begin the zero process and advance to
the Zero In-process Screen.
Press ON/OFF/MODE to bypass zero and calibration
and advance to one of two screens.
If bump test in-field is enabled, the user advances to the
Bump Test Initiate Screen.
Zero Initiate Screen If bump test in-field is disabled, the user advances to the
Options: Peak Readings Screen.
Enter Zero
Bypass Zero


Allow the zero process to complete and advance to the
Zero Results (Pass or Fail) Screen.
After the zero process, press ON/OFF/MODE to

bypass calibration of the installed toxic and combustible
sensors. The user returns to the mode from which the
calibration process was entered (configuration or gas
Zero In-process Screen monitoring).
Each sensor’s numerical value becomes zero except
O2. An updated O2 span value displays. The clock icon NOTE: during the zero process, the O2 sensor is calibrated (when set to
flashes and the zero icon displays. default gas volume of 20.9%)
NOTE: The “span reserve” of a sensor measures its sensitivity. The

displayed span value divided by the calibration gas value equals the
span reserve percentage. A span reserve percentage of greater than
70% indicates a “good” sensor; 50%-70% indicates “marginal”
sensitivity. When the span reserve percentage is less than 50%, the
sensor will not pass calibration.
Within Ten Seconds

Press ENTER to repeat the zero process.
Press ON/OFF/MODE to advance to one of two screens.
If zero was entered from…
Zero Results (Pass) Screen …configuration mode, the user advances to the
The check mark displays to indicate a successful zero Calibration Apply Gas Screen.
and a short beep sounds. Each sensor’s numerical
values display at zero except O2. … gas monitoring mode and the calibration in-field option
is enabled, the user advances to the Calibration Apply
Options: Gas Screen.
Repeat zero
Begin calibration …gas monitoring mode and the calibration in-field option
is disabled, the user advances to the Gas Monitoring
Enter gas monitoring mode
Screen in the gas monitoring mode.
If neither ENTER nor ON/OFF/MODE is pressed, within

ten seconds, the user advances to the Gas Monitoring
Screen in the gas monitoring mode.
Press ON/OFF/MODE (or wait ten seconds) to return to
the Zero Initiate Screen and repeat the zero process.
Zero Results (Fail) Screen

Displays an “F” or “P”, respectively, for each failed or
passed sensor. For O2, if the sensor passed its
calibration, the sensor reading displays.


To Terminate
Press ON/OFF/MODE while the gas cylinder icon flashes
to terminate the quick calibration process (or to skip a
sensor’s calibration in standard calibration) and return to
Calibration Apply Gas Screen* To Calibrate

The gas cylinder icon flashes. Each sensor’s display From the already prepared gas cylinder, start the flow of
shows the calibration gas concentration to be applied. gas as noted below for the monitor/regulator combination
(The O2 display is blank as the sensor was calibrated in use.
during zeroing.) The monitor waits up to five minutes to
successfully sense the gas. For an aspirated monitor with a demand flow regulator,
complete the tubing connection from the regulator to the
Calibration In-progress Screen* pump inlet.
If gas is sensed, the gas values for the LEL and toxic
sensors increase and the O2 value decreases. For an aspirated monitor with a positive flow regulator,
turn (counterclockwise) the regulator’s knob.
If gas is NOT sensed, a failed calibration registers and
the Calibration Failed Screen displays. For a diffusion monitor with a positive flow regulator:
• Place the calibration cup over the upper portion of
the monitor’s case top (front of monitor). To attach
properly, complete or observe the following.
o The cup fully covers the sensor ports.
o The monitor’s display and buttons are NOT covered.
o The cup’s side arms fit securely in the grooves on
the sides of the monitor.
o The Ventis name on the calibration cup is upright
and readable.
o The cup’s nipple points up and away from the
monitor.
• Turn (counterclockwise) the regulator’s knob.
STOP THE FLOW OF GAS.
After calibration, or if calibration is terminated at any time
during the process, stop the flow of gas as follows.
For an aspirated monitor with a demand flow regulator,

disconnect the tubing from the pump inlet.
For an aspirated or diffusion monitor with a positive

flow regulator, turn (clockwise) the regulator’s knob.
Sensor Results Screen* All Sensors Pass

Pass (top) or Fail (bottom) Screen The user returns to the mode from which the calibration
process was entered (configuration or gas monitoring).
The display alternately shows a “P” for pass (or “F” for
fail) and the final span value reading for each sensor. A
check mark displays and a single beep sounds. Sensor Fail
NOTE: The “span reserve” of a sensor measures its sensitivity. The If one or more sensors fail calibration, the Calibration Fail
displayed span value divided by the calibration gas value equals the Screen displays and a system level alarm turns on.
span reserve percentage. A span reserve percentage of greater than
70% indicates a “good” sensor; 50%-70% indicates “marginal”
sensitivity. When the span reserve percentage is less than 50%, the
sensor will not pass calibration.


Any failed sensor stays in alarm until it passes a
calibration or is replaced.
Press ON/OFF/MODE to repeat calibration.
Calibration Failed Screen*

Gas readings display for all successfully calibrated
sensors and an “F” displays for any failed sensors. A
system level alarm turns on. The warning icon and gas
cylinder display to indicate a sensor calibration failure.
* During the standard calibration or standard bump test process, a series of apply gas, in-progress, and results screens show for EACH sensor as it
is calibrated or tested.
Bump Test Process

Press ON/OFF/MODE to bypass the bump test process
and advance to the Peak Readings Screen.
Press ENTER to begin the bump test process.
Bump Test Initiate Screen

Options
Begin process
Bypass process
To Terminate
Press ON/OFF/MODE while the gas cylinder icon flashes
to terminate the quick bump test process (or to skip a
sensor’s testing in standard bump testing). The user
returns to the Gas Monitoring Screen.
To Bump Test
Bump Test Apply Gas Screen
Displays the bump test gas concentrations the monitor From the already prepared gas cylinder, start the flow of
is expecting to receive. The monitor waits up to five gas as noted below for the monitor/regulator combination
in use.
minutes to successfully sense the gas.
For an aspirated monitor with a demand flow regulator,

If gas is sensed, the user advances to the Bump Test
complete the tubing connection from the regulator to the
In-progress Screen.
pump inlet.
If gas is NOT sensed, a failed bump test occurs and the

For an aspirated monitor with a positive flow regulator,
user advances to the Bump Test Results Screen
displays. turn (counterclockwise) the regulator’s knob.
For a diffusion monitor with a positive flow regulator:

• Place the calibration cup over the upper portion of
the monitor’s case top (front of monitor). To attach
properly, complete or observe the following.

Bump Test Process

o The cup fully covers the sensor ports.
o The monitor’s display and buttons are not covered.
o The cup’s side arms fit securely in the grooves on
the sides of the monitor.
o The Ventis name on the calibration cup is upright
and readable.
o The cup’s nipple points up and away from the
monitor.
• Turn (counterclockwise) the regulator’s knob.
As the bump test progresses, observe the display
activity (left).
After the bump test, the Bump Test Results Screen

displays.
Bump Test In-progress Screen STOP THE FLOW OF GAS.

Displays when gas is sensed within five minutes. The After bump testing, or if bump testing is terminated at
clock icon flashes to indicate the test is in-progress. The any time during the process, stop the flow of gas
sensor reading(s) display. The LEL and toxic sensor from the cylinder as follows.
readings increase and the O2 reading decreases.
For an aspirated monitor with a demand flow
regulator, disconnect the tubing from the pump inlet.
For an aspirated or diffusion monitor with a

positive flow regulator, turn (clockwise) the
regulator’s knob.
No User Action Required
After a passed bump test, the monitor goes into gas
monitoring mode.
Bump Test Results (Pass) Screen

The above displays an all sensor pass result. If one or
more sensors fail, the “F” shows in place of the “P”. The
pass/fail screen (left) and the final sensor reading
screen (right) display alternately three times. A single
beep sounds to indicate the bump test is completed.
After a failed bump test, the Bump Test Fail Screen
displays and a low level audio alarm turns on.
The monitor should be fully calibrated after a failed bump

test.
NOTE: After a full calibration, the O2 sensor must pass a bump test to
Bump Test Results (Fail) Screen clear the bump test fail status.
The “bF” displays under each gas type to indicate a
bump test failure. The system level alarm turns on and
the gas cylinder icon flashes.

Bump Test Process

Press and release ENTER to clear the peak values, if
desired.
Press ON/OFF/MODE to advance to one of two screens.
If toxic sensors are installed, the user advances to the

TWA Readings Screen.
Peak Readings Screen
Displays the peak icon and peak gas concentrations for If no toxic sensors are installed, the user advances to the
each installed sensor since the last time the peak Gas Monitoring Screen.
readings were cleared. (For O2, the lowest reading is
shown.)
Press and release ENTER to clear the displayed TWA
reading(s), if desired.
Press ON/OFF/MODE to advance to the STEL Readings
Screen.
TWA Readings Screen

Displays the TWA (time weighted average) icon and
calculated readings for each toxic sensor installed; all
other sensor values are blank.
Press and release ENTER to clear the reading(s), if
desired.
Press ON/OFF/MODE to advance to the Gas Monitoring
Screen.
STEL Readings Screen

Displays the STEL (short term exposure limit) icon and
STEL values for each toxic sensor installed; all other
sensor values are blank. The STEL value is the running
average over the last 15 minutes.
* During the standard calibration process, a series of apply gas, in-progress, and results screens show for EACH sensor as it is calibrated or tested.
Remote Sampling
Aspirated monitor
In confined space, an air sample should be taken in four foot (1.2192 m) intervals.
Guidelines for using a motorized pump and sampling line
When sampling with a motorized pump and sampling line, Industrial Scientific recommends the following:
• Choose the tubing type based on the target gases. If the target gases are known, use Teflon-lined tubing when
sampling for these gases: chlorine (Cl2), chlorine dioxide (ClO2), hydrogen chloride (HCl), and volatile organic
compounds (VOCs). For other known target gases, urethane tubing or Teflon-lined tubing may be used.
When the target gases are unknown, use Teflon-lined tubing.
• Know the length of the sample line as it is a factor in determining sampling time. A sample line may consist of
tubing, a probe, or a probe and tubing. It should also have a dust filter–water stop installed at the line's end that
will extend into the sample area. Sample-line length is defined as the distance from the dust filter–water stop

opening to the point where the line connects to the pump's inlet. Ensure sample-line length does not exceed the
pump's maximum draw.
• Before and after each air sample, perform a test of the full sampling line.
o Use a thumb to block the end of the sampling line at the water-stop opening. This should cause a pump-fault
alarm.
o Remove the thumb from the water-stop opening. After the alarm cycle completes, the pump should resume
normal operation.
Note: If a pump fault does not occur, check and correct for cracks or other damage, debris, and proper
installation in these areas: all sampling line connections, the pump's inlet cap and inlet barrel, and the dust filter-
water stop items at the end of the sampling line and inside the pump inlet barrel.
• Based on sample-line length, calculate the minimum time recommended for the air sample to reach the
instrument's sensors. As shown below, use a base time of 2 minutes, and add 2 seconds for each 30 cm (1 ') of
line length. Watch the display screen for gas readings and, if present, allow them to stabilize to determine the
reading.
Minimum sample time for common sample-line lengths

Sample-line length Base time + Sample-line-length = Minimum sample time
(minutes) factor (seconds) (mm:ss)
3.05 m (10 ') 2 min + (10 x 2 s) = 02:20
6.10 m (20 ') 2 min + (20 x 2 s) = 02:40
9.14 m (30 ') 2 min + (30 x 2 s) = 03:00
12.10 m (40 ') 2 min + (40 x 2 s) = 03:20
15.24 m (50 ') 2 min + (50 x 2 s) = 03:40
18.29 m (60 ') 2 min + (60 x 2 s) = 04:00
21.34 m (70 ') 2 min + (70 x 2 s) = 04:20
24.38 m (80 ') 2 min + (80 x 2 s) = 04:40
27.43 m (90 ') 2 min + (90 x 2 s) = 05:00
30.48 m (100 ') 2 min + (100 x 2 s) = 05:20
Cleaning
• NEVER use solvents or cleaning solutions of any type.
• When necessary, wipe the outside of the Ventis MX4 with a soft, clean cloth.
• Make sure the sensor diffusion membrane, inside and out, is free of debris; wipe gently with a cloth or brush that
is soft, clean, and dry.
• Make sure the aspirated monitor’s inlet is free of debris.
Service
Instructions are provided for battery service; monitor conversion; sensor, sensor barrier and LCD service; and pump
assembly service. Refer to the three-dimensional view diagrams to identify the parts referenced in the instruction
sets, and for screw torque values.
Read all instructions before beginning any monitor service.
NOTICES

→ Before beginning any service tasks, power-off the monitor.

→ Only qualified staff should perform monitor service and should take the following precautions.
→ Take care not to touch battery contacts on the monitor or the battery itself.
→ Perform work in a clean air environment that is known to be nonhazardous.
→ Perform work on a nonconductive work surface.
→ Wear grounding straps.
Alkaline battery setup
1. Unlatch and lift the hinged portion of the battery housing.
2. Place AAA battery types Energizer EN92 or Duracell MN2400 so the negative (-)
end of the battery, touches the spring inside the battery housing. Do NOT mix
battery types.
3. When all three AAA batteries are properly installed, close the battery housing. A
“Click” will be heard when the latch catches securely.
4. When replacing batteries, dispose of spent batteries according to company
policy.
Aspirated Monitor
The aspirated monitor can be used with two Ventis battery types.
• The Extended range Li-ion battery
• The Alkaline battery
Power off the instrument before disassembling it or performing any service task.
Pump with battery installation
Unscrew and remove the Unscrew, lift, and remove Loosen the pump door Slide the pump door
belt clip. Store the clip, the battery from the screw. down.
screw, and washer for diffusion instrument; store
future use. it for future use.
Lift door to open. Install a compatible Place the instrument in the Lower the pump door.
Extended range battery— pump case; tighten* the Slide it into its fully
label side up—into the four torx screws on the closed, clicked-shut
lower receptacle of the back of the pump. position.
pump case.

— — —
Tighten* the pump door

screw.
Pump door replacement
Loosen the pump door screw. The door is hinged to the pump module with two pegs
Slide the pump door down; lift it to open. that slide into grooves. Angle the door so that one peg
moves to the bottom of its groove and the other moves
the top of its groove. Lift the door to remove it.
Install the new door in the same manner the door was
removed.
— —
Lower the pump door. Slide it into its fully closed, clicked-shut position. Tighten* the pump door screw.
*Torque value is .39 Newton-meters (55 ounce-force inch)
Pump cap and water barrier replacement
To unscrew and remove Remove the water barrier Place the new water barrier inside the inlet barrel; the
the pump cap, turn it in a from the inlet barrel. side with the larger filter surface should face the user.
counterclockwise
direction.

— — —
Secure the pump cap to

the inlet barrel: turn it in a
clockwise direction to
tighten.
Diffusion Monitor
The diffusion monitor can be used with all four Ventis battery types:
• The Li-ion battery
• The Slim extended Li-ion battery
• The Extended range Li-ion battery
• The Alkaline battery
Battery installation
Using a torx screwdriver, loosen all four screws from the Lift the battery (left) or battery cover and Extended
battery (left) or the battery cover (right). range battery (right) away from the instrument.
Note: The Extended range battery will easily fit into the battery cover. If the battery does not easily insert, stop to ensure proper
placement as noted in the instruction.
To install the Extended range battery, first place the To install the battery, Using a torx screwdriver,
battery in the battery cover. When placed correctly, align it with the tighten* each of the four
the battery's label will show. instrument. screws to secure the
battery (shown) or
Next, align the battery cover with the instrument. battery cover to the
instrument.
*Torque value is .39 Newton-meters (55 ounce-force inch).

Suspender clip
When worn, the diffusion monitor should be fastened securely and attached to ensure the sensor portals are exposed
to the air. The monitor should be in full view. No part of the monitor should be covered by any garment or part of a
garment.
Clip replacement
Clip only (use with battery and Slim extended battery)
Lift the clip's cover. To remove the clip, use a To attach the clip, put the washer onto the screw and
Phillips screwdriver to place the screw in the clip's middle hole.
access the clip's screw.
Turn counterclockwise to Turn the screw clockwise to tighten*.
loosen the screw.
Remove the screw,
washer, and clip; set aside
or store for future use.
Clip with spacer (use with Extended battery and battery cover)
To remove the clip, use a To attach the clip and Guide the screw into the
Phillips screwdriver to spacer, cover the case spacer's hole and into the
access the clip's screw. bottom's platform with the instrument case bottom.
Turn counterclockwise to spacer.
loosen the screw. Turn clockwise to tighten*.
Put the washer onto the
Remove the washer, screw and place the screw
screw, clip, and spacer; in the clip's middle hole.
set aside or store for
future use.
Sensor, Sensor Barrier, LCD, and vibrating motor replacement

Service instruction sets are provided below. Follow the instruction relevant to the desired task and take note of the
following:
• The monitor has a two-part circuit board assembly, the main board and a smaller sensor board. They are
attached to one another with a connecter at the center of the sensor board.
• The sensor barrier can be replaced as an assembly that fits in the monitor’s case top, or the full case top can be
replaced. NOTE: When a sensor is replaced, it is recommended that the sensor barrier/case top also be
replaced. After reassembling the monitor, a full calibration should be completed.
• The LCD is removed and attached as a single component.

Disassembling the Monitor. (For the Diffusion monitor start with Step 6.)
1 Power-off the monitor.
2 Loosen the four captive screws on the lower portion of the pump case module bottom (back of the
module).
3 Loosen the single captive screw on the pump case module top.
4 Loosen the front door screw; slide the case door down; lift the hinged door to reveal and access the
monitor.
5 Lift and remove the monitor from the pump module; set aside the module.
6 Place the monitor display side down. For a diffusion monitor loosen the four captive battery screws to
separate the battery from the case bottom.
7 Loosen the two captive screws on the upper portion of the case bottom.
8 Lift to separate the monitor case top from the monitor case bottom to reveal the circuit board assembly.
9 Remove the circuit board assembly and set aside the monitor case top and bottom.
10 Separate the main circuit board from the sensor board.
Replacing the LCD
1 Grasp the sides of the LCD and lift straight up to remove from the main circuit board.
2 To properly place the new LCD, align the pins on the LCD with their receptacles on the main circuit board.
3 Gently press straight down and into place.
Replacing the Sensor(s)
1 Identify the sensor to be removed.
2 Gently lift and remove the sensor.
3 To add the new sensor, align its pins or connector(s), with the respective receptacles on the sensor board.
4 Press down. A slight click indicates the sensor is securely in place.
Reassembling the Circuit Board Assembly
1 Re-attach the main circuit board to the sensor board, aligning their connectors.
2 Press. A slight click indicates the boards are securely attached.
Replacing the Sensor Barrier or Case Top
To replace the sensor barrier on the inside of the case top, follow steps 1-5 below.
To replace the entire case top, skip to the instruction set, “Reassembling the Monitor”.
1 Observe the placement of the existing sensor barrier. Note that each cut-out is shaped to match the
sensor it protects.
2 Lift and remove the sensor barrier and gasket from inside the monitor case top. Ensure the entire case top
is free of adhesive; gently scrape, if needed. Wipe with a clean, dry, soft cloth or brush.
3 Lift the backing from the new sensor barrier assembly to reveal the adhesive.
4 Carefully position the new barrier. Each shaped opening matches the shape of the sensor it protects.
Press to attach to the inside of the case top.
Replacing the Vibrating Motor
1 Place the monitor’s case top face down.
2 Lift the vibrating motor from its partition. The partition has two sections divided by a ridge. Discard the
used motor.
3 To properly place the new vibrating motor, its contact pins face the user and align with the left edge of the
partition. (The motor’s movable component fits within the small section of the partition.)
4 Press into place.

Reassembling the Monitor

1 Re-place the board assembly into the monitor’s case bottom. The LCD faces the user.
2 Re-place the monitor’s case top (or place its new case top).
3 Tighten* the two captive screws on the upper portion of the monitor case bottom.
4 Re-place the monitor inside the pump module. The monitor is display side up and its logo readable. Its
lower exposed bottom portion covers the battery. For the diffusion monitor, re-place the battery or battery
cover assembly.
5 Tighten* the four screws on the pump module bottom to secure the module to the monitor, or tighten* the
four captive screws on the battery pack for a diffusion monitor.
6 Close the pump module door; slide up to click in place.
7 Tighten* the pump door screw to secure.
8 Dispose of the used sensor(s) according to company policy.
9 Perform a full calibration following the addition or replacement of any sensor, or the replacement of the
sensor water barrier or monitor case top.

Ventis MX4 Monitor three-Dimensional Diagram

Key for Ventis MX4 Monitor three-Dimensional Diagram

Number Part Number (P/N) Description
1 17152380-X Ventis MX4 Diffusion Case Top Assembly (includes items 2 and 3)
X = Case Color, where: 0 = Black, 1 = Orange
2 17152429 Sensor Barrier Assembly

3 17145285 Vibrating Motor
4 17150772 Ventis MX4 LCD Assembly
5 17134495 Ventis MX4 Sensor, Combustible Gas (LEL/CH4)
6 17134461 Ventis MX4 Sensor, Oxygen (O2)
7 17134487 Ventis MX4 Sensor, Carbon Monoxide (CO)
7 17155564 Ventis MX4 Sensor, Carbon Monoxide/Low Hydrogen Interference (CO/H2 Low)
8 17134479 Ventis MX4 Sensor, Hydrogen Sulfide (H2S)
9 17134503 Ventis MX4 Sensor, Nitrogen Dioxide (NO2)
10 17143595 Ventis MX4 Sensor, Sulfur Dioxide (SO2)
11 17147281 Captive Case Screw, Torx (torque value: 55 oz-in or .39 N.m +/- 10%)
12 17152506** Suspender Clip Spacer
13 17120528** Suspender Clip
14 17153137** Locking Washer
15 17152507** Screw, Phillips (for use with items 12, 13 and 14) (torque value: 125 oz-in or .88 N.m +/- 10%)
16 17139262 Screw, Phillips (torque value: 125 oz-in or .88 N.m +/- 10%)
Batteries
17 17134453-XY Lithium-ion battery
18 17157350-XY Slim extended lithium-ion battery

See Battery part numbers and
19 17148313-Y Extended range lithium-ion battery options for orderable part
numbers.
20 17150608-XY Alkaline battery
(CSA, China MA, and China KA approved for Screw Torque: 0.39 newton m
diffusion monitor only.) (55 ounce-force inch)
21 17151184-XY** Battery cover (for use with Extended

range battery)
* Item in diagram is not user replaceable. The Ventis MX4 monitor must be sent to an authorized ISC Service Center for this item to be replaced.
** Available in a conversion kit – VTSB-2XY (orderable part number); when converting an aspirated monitor to a diffusion monitor with a rechargeable
Extended range Li-ion battery or Alkaline battery. (Batteries sold separately.)

Battery Configuration
The base part number that appears on the label of a Ventis battery item uses an eight-digit numeric format
(XXXXXXXX). The corresponding orderable part numbers use the four-letter base reference "VTSB", which is followed
by a three character suffix. The first suffix character is a number that designates the battery type; the second and third
are used to indicate color and approval options, respectively. For example, as shown below in the Battery part numbers
and options, a rechargeable Slim extended lithium-ion battery kit that is black and has a UL approval would have an
orderable part number of VTSB-401 and its label would state a part number of 17157350-01.
Battery part numbers and options

Diagram Battery kit Part numbers Optionsa (X and Y)
number
Label Orderable kit
17 Rechargeable Lithium-ion 17134453-XY VTSB-1XY X indicates color:
battery 0 for black; 1 for orange
18 Rechargeable Slim 17157350-XY VTSB-4XY Y indicates approvals:
extended lithium-ion
battery 1 for UL, CSA, ATEX, IECEx,
EAC (GOST-K and GOST-R),
c b
19 and 21 Rechargeable Extended 17148313-Y VTSB-2XY (kit) KOSHA, MED, SANS, and
range lithium-ion battery (battery) TllS; 2 for MSHA; 3 for China
kit (includes battery and 17151184-XY EX; 4 for ANZEx; 5 for
cover) (cover) INMETRO; and C for China
KA
c
20 Alkaline battery 17150608 VTSB-3XY
a
Color and approval options may vary for each battery item. For more information, contact Industrial Scientific or an authorized distributor of its
products.
b
The battery and cover may be ordered separately using these part numbers 17148313-Y (battery) 17151184-XY (cover).
c
Aspirated instruments only.

Ventis MX4 Pump module three-Dimensional Diagram
KEY FOR VENTIS MX4 PUMP MODULE THREE-DIMENSIONAL DIAGRAM

1 17151150-X0 Ventis MX4 Pump Door Assembly
X = Pump Door Assembly Color, where: 0 = Black, 1 = Orange
(captive screw torque value: 55 oz. in. or .39 n.m . +/- 10%)
2 17129909 Pump Inlet Filter Cap

2 17141581 Pump Inlet-Filter Cap for use 6’ extendable probe
2 17141599 Filter Cap, 1/8 NPT Female
3 17152395 Water Barrier
4 17151275 Screw, Torx (torque value: 55 oz-in or .39 N.m +/- 10%)
5 17052558 Screw (torque value: 25 oz-in or .17 N.m +/- 10%)
6 17148313-Y Extended Range Lithium-ion Battery Pack
Y = Approval where:
1 = UL, CSA, ATEX, IECEx, INMETRO, GOST-R, GOST-K, KOSHA, and TIIS
2 = MSHA
3 = China Ex
4 = ANZEx

KEY FOR VENTIS MX4 PUMP MODULE THREE-DIMENSIONAL DIAGRAM

7 17150608 Alkaline Battery: UL, ATEX, IECEx, ANZEx, and INMETRO approvals (CSA,
China KA and China MA approved for diffusion monitor only.)
* Item is not user replaceable. The Ventis MX4 Pump Module must be sent to an authorized ISC Service Center for this item to be replaced.
►Products, Specifications, and Certifications
Ventis MX4 Accessories and Parts
Sensors, Sensor Barrier, Vibrating Motor, LCD, and Calibration Cup

17134495 Ventis MX4 Sensor, Combustible Gas (LEL/CH4)
17134461 Ventis MX4 Sensor, Oxygen (O2)
17134487 Ventis MX4 Sensor, Carbon Monoxide (CO)
17155564 Ventis MX4 Sensor, Carbon Monoxide/Low Hydrogen Interference (CO/H2 Low)
17134479 Ventis MX4 Sensor, Hydrogen Sulfide (H2S)
17134503 Ventis MX4 Sensor, Nitrogen Dioxide (NO2)
17143595 Ventis MX4 Sensor, Sulfur Dioxide (SO2)
17152380-X Diffusion Case Top Assembly (includes Sensor Barrier Assembly)
X = Case Top Color, where: 0 = Black, 1 = Orange
17152429 Sensor Barrier Assembly

17145285 Vibrating Motor
17150772 Ventis MX4 LCD Assembly
17156189 Ventis Calibration Cup Assembly, calibration cup with tubing
17152455 Ventis Calibration Cup
Monitor Specifications
Item Description
Display Backlit Liquid Crystal Display (LCD)
Buttons Two (ON/OFF/MODE and ENTER)
Monitor case Polycarbonate with ESD protective rubber overmold
Alarms Ultra-bright LEDs, loud audible alarm (95dB at 30 cm), and vibrating alarm
Size and Weight Diffusion with Lithium-ion Diffusion with Slim Aspirated with Extended
(typical) extended Lithium-ion Range Lithium-ion
(typical) (typical)
Size 103 mm x 58 mm x 30 mm 103 mm x 58 mm x 36 mm 172 mm x 67 mm x 66 mm
(4.1” x 2.3” x 1.2”) (4.1” x 2.3” x 1.4”) (6.8” x 2.6” x 2.6”)
Weight 182 g (6.4 oz) 207 g (7.3 oz) 380 g (13.4 oz)

Battery Specifications
The battery specifications table shown below, includes run time, charge time, charging temperature requirements,
and expected lifetime.
Battery specifications table

Rechargeable Replaceable
batteries batteries
(part number) (part number)
Lithium-ion Slim extended Extended range Alkaline battery
battery lithium-ion battery lithium-ion battery
c c c c
(VTSB-1XY ) (VTSB-4XY ) (VTSB-2XY ) (VTSB-3XY )
a
Run time Diffusion 12 hours 18 hours 20 hours 8 hours
a
Run time Aspirated _ _ 12 hours 4 hours
b
Charge time up to 5 hours up to 7 hours up to 7.5 hours _
Ambient temperature 0 − 40 °C 0 − 40 °C 0 − 40 °C _
required for charging (32 − 104 °F) (32 − 104 °F) (32 − 104 °F)
a
Approximate run time when the battery is fully charged, and operating at room temperature.
b
When a lithium-ion battery becomes deeply discharged and the instrument is docked, it can take up to an hour for the instrument
display to indicate that the battery is charging.
c
X indicates color and Y indicates approvals.
Note: Batteries can withstand 300 charge cycles over their lifetime.
Operating Conditions
Warm-up time 40 seconds (includes stabilization time)
Temperature range -20 °C to +50 °C (-4 °F to +122 °F)
Humidity range 15–95% relative humidity (RH) noncondensing (during continuous operation)
Pressure range 1 atm ±20%
Cold-weather Operation
Use caution when operating the instrument in temperatures below -20 °C (-4 °F), which can diminish display-screen
legibility. To help support functionality and available battery power, the following practices are recommended.
• Do not operate the instrument in temperatures that are not within the temperature ranges of the installed sensors
(see "Sensor specifications").
• Use a compatible, fully charged lithium-ion battery.
• Before using the instrument in the cold-weather environment, power it on a warm-up environment (approximately
20 °C [68 °F]).
• Alternately operate the instrument in the cold-weather and warm-up environments.
• Do not operate the instrument unmanned.
Storage Conditions
Temperature range 0−25 ºC (32−77 ºF)
Humidity range 40–70% relative humidity (RH) noncondensing
Pressure range 0.9–1.1 atm
Maximum time Up to 6 months
Note: Industrial Scientific recommends that infrequently used lithium-ion batteries be
fully charged every four months.

Sensor Specifications
Gas Name Abbr. Measuring Resolution Accuracy at Time and Response Response
Range Temperature of Time Time
Calibration* (typical) (typical)
T50 T90
Oxygen O2 0–30% vol 0.1% vol ± 0.5% 15 30
Carbon Monoxide CO/H2 0–1000 ppm 1 ppm ± 5% (0-300 ppm) 8 17

with low H2 Low ± 15% (301-1000 ppm)
interference
Carbon Monoxide CO 0–1000 ppm 1 ppm ± 5% 15 50
Hydrogen Sulfide H2S 0–500 ppm 0.1 ppm ± 5% 15 30
Nitrogen Dioxide NO2 0–150 ppm 0.1 ppm ± 10% 10 30
Sulfur Dioxide SO2 0–150 ppm 0.1 ppm ± 10% 20 80
Combustible LEL 0–100% LEL 1% LEL ± 5% 15 35
Methane CH4 0–5% vol 0.01% vol ± 5% 15 35

*The accuracy specification for each sensor is ± the stated percentage or 1 unit of resolution, whichever is greater.
Toxic Gas Sensor Cross-sensitivity Table
Target Gas Sensor
CO
(H2
CO Low) H2S SO2 NO2 Cl2 ClO2 HCN HCl PH3 NO H2 NH3
CO 100 100 1 1 0 0 0 0 0 0 0 20 0
H2S 5 5 100 1 -40 -3 -25 10 300 25 10 20 25
SO2 0 5 5 100 0 0 0 — 40 — 0 0 -40
NO2 -5 5 -25 -165 100 45 — -70 — — 30 0 -10
Cl2 -10 0 -20 -25 10 100 60 -20 6 -20 0 0 -50
ClO2 — — — — — 20 100 — — — — — —
HCN 15 — 10 50 1 0 0 100 35 1 0 30 5
HCl 3 — 0 5 0 2 0 0 100 0 15 0 0
PH3 — — — — — — -100 425 300 100 — — —
NO 25 40 1 1 5 — — -5 — — 100 30 0
H2 22 3 0.1 0.5 0 0 0 0 0 0 0 100 0
H3 0 0 0 0 0 0 0 0 0 0 0 0 100
The Sensor Cross Sensitivity Table (above) reflects the percentage response provided by the sensor (top row) when exposed to a
known concentration of the target gas (column 1).
The numbers were measured under these environmental conditions: 20 °C (68 °F) , 50% RH and 1 atm.
The specified cross-interference numbers apply to new sensors only, and may vary with time as well as from sensor to sensor.
“—” means no data available.
This table is given as a reference only and is subject to change.

LEL, and LEL Correlation Factors for Combustible Gases

Sample gas* LEL LEL correlation factors
(% vol)
Calibration gas
Butane Hexane Hydrogen Methane Pentane Propane
Acetone 2.5% 1.00 0.70 1.70 1.70 0.90 1.10
Acetylene 2.5% 0.70 0.60 1.30 1.30 0.70 0.80
Benzene 1.2% 1.10 0.80 1.90 1.90 1.00 1.20
Butane 1.9% 1.00 0.58 1.78 1.67 0.83 1.03
Ethane 3.0% 0.80 0.60 1.30 1.30 0.70 0.80
Ethanol 3.3% 0.89 0.52 1.59 1.49 0.74 0.92
Ethylene 2.7% 0.80 0.60 1.40 1.30 0.70 0.90
Hexane 1.1% 1.71 1.00 3.04 2.86 1.42 1.77
Hydrogen 4.0% 0.56 0.33 1.00 0.94 0.47 0.58
Isopropanol 2.0% 1.10 0.90 2.00 1.90 1.00 1.20
Methane 5.0% 0.60 0.35 1.06 1.00 0.50 0.62
Methanol 6.0% 0.60 0.50 1.10 1.10 0.60 0.70
Nonane 0.8% 2.22 1.30 3.95 3.71 1.84 2.29
Pentane 1.4% 1.21 0.71 2.15 2.02 1.00 1.25
Propane 2.1% 0.97 0.57 1.72 1.62 0.80 1.00
Styrene 0.9% 1.30 1.00 2.20 2.20 1.10 1.40
Toluene 1.1% 1.53 0.89 2.71 2.55 1.26 1.57
Xylene 1.1% 1.50 1.10 2.60 2.50 1.30 1.60
JP-4 — — — — — 1.20 —
JP-5 — — — — — 0.90 —
JP-8 — — — — — 1.50 —
NOTE: The table above provides the LEL for select combustible gases*. It also provides correlation factors that help the safety
technician and instrument operator determine the actual percentage LEL when the sample gas differs from the gas that was used to
calibrate the unit.
For example, if the unit reads 10% LEL in a pentane atmosphere, and was calibrated to methane, the actual percentage LEL is
determined as follows:
1. Locate the table cell where the sample gas (pentane) intersects with the calibration gas (methane).
2. Multiply the cell's value (2.02) by the unit's LEL reading (10%) to calculate the actual concentration of 20.2% LEL.
* The combustible gas list is not a comprehensive list of all combustible gases that can be detected by the Ventis MX4. For
additional information about combustible gas detection and the Ventis MX4, contact the ISC Technical Service department.

Certifications
Certifications for the Ventis™ MX4 Multi-Gas Monitor, at the time of this document's publication, are listed below in
the Hazardous-area certifications table. To determine the hazardous-area classifications for which an instrument is
certified, refer to its label or the instrument order.
Hazardous-area certifications table
Certifying Body Area Classifications Approved Temperature

(CB) Range
ANZEx Ex ia s Zone 0 I/IIC, Temperature Class T4 -20 °C to +50 °C
(-4 °F to +122 °F)
a
ATEX Ex ia IIC, equipment protection level Ga, Temperature Class T4; -20 °C to +50 °C
Ex ia I, equipment protection level Ma; (-4 °F to +122 °F)
Equipment Group and Category II 1G and I M1
China Ex Ex ia IIC, equipment protection level Ga, Temperature Class T4; -20 °C to +50 °C
Ex ia d l Mb (-4 °F to +122 °F)
China CMC Metrology approval -20 °C to +50 °C
(-4 °F to +122 °F)
China MA Approved with underground mines with CO, H2S, O2 and CH4 -20 °C to +50 °C
(Diffusion with 17134453 battery only.) (-4 °F to +122 °F)
CSA Class I, Groups A, B, C, and D, Temperature Class T4 -20 °C to +50 °C
Ex d ia IIC, Temperature Class T4 (-4 °F to +122 °F)
GOST EAC PBExiadl X / 1ExiadllCT4 X -20 °C to +50 °C
GOST-R Metrology approval, GOST-K Metrology (-4 °F to +122 °F)
a
IECEx Ex ia IIC, equipment protection level Ga, Temperature Class T4 -20 °C to +50 °C
(-4 °F to +122 °F)
INMETRO Ex ia IIC, equipment protection level Ga, Temperature Class T4 -20 °C to +50 °C
(-4 °F to +122 °F)
KOSHA Ex d ia IIC, Temperature Class T4 -20 °C to +50 °C
(-4 °F to +122 °F)
MASC SANS 1515-1; Type A; Ex ia l/llC, Temperature Class T4 -20 °C to +50 °C
(-4 °F to +122 °F)
MED MED 2014/90/EU Marine Directive -20 °C to +50 °C
(-4 °F to +122 °F)
b
MSHA 30 CFR Part 22; Permissible for Underground Mines –
(Lithium-ion packs only)
UL Class I, Division 1, Groups A, B, C, and D, Temperature Class T4 -20 °C to +50 °C
Class II,Groups F, and G (-4 °F to +122 °F)
Class I, Zone 0, AEx ia IIC, Temperature Class T4
a
Marking requirements are reproduced in the section below.
b
MSHA requires the monitor be calibrated according to the procedures in the Product Manual only. MSHA also requires the monitor
display methane in the percent-by-volume mode (0-5%) for compliance determinations required by 30 CFR Part 75, subpart D.

Marking Requirements
ATEX Markings IECEx Markings

Industrial Scientific Corp. Industrial Scientific Corp.
15205 USA 15205 USA
VENTIS MX4 VENTIS MX4
DEMKO 10 ATEX 1006410 IECEx UL10.0034
Ex ia IIC T4 Ga Ex ia IIC T4 Ga
Ex ia I Ma -20oC ≤ Ta ≤ +50oC
EN 60079-29-1 IP 66/67
EN 50104
II 1G and I M1
-20oC ≤ Ta ≤ +50oC
IP 66/67
Aspirated Configuration Aspirated Configuration

Use only replaceable battery pack P/N 17148313-1 or Use only replaceable battery pack P/N 17148313-1 or
17050608. 17050608.
Do Not Recharge or Replace battery in Hazardous Locations. Do Not Recharge or Replace battery in Hazardous Locations.
Charging contact parameters: Um = 6.2V; Ii = 1.3A Charging contact parameters: Um = 6.2V; Ii = 1.3A
[Serial Number] [Month/Year of Production] [Serial Number] [Month/Year of Production]
Diffusion Configuration Diffusion Configuration
Use only replaceable battery pack P/N 17148313-1, Use only replaceable battery pack P/N 17148313-1,
17157350-XX, or 17134453-X1. 17157350-XX, or 17134453-X1.
Do Not Recharge or Replace battery in Hazardous Locations. Do Not Recharge or Replace battery in Hazardous Locations.
Charging contact parameters: Um = 6.2V; Ii = 1.3A Charging contact parameters: Um = 6.2V; Ii = 1.3A
[Serial Number] [Month/Year of Production] [Serial Number] [Month/Year of Production]
Alkaline Battery Pack, P/N 17150608

Do Not Recharge or Replace battery in Hazardous Locations.
Only approved for use with three (3) AAA battery types
Duracell MN2400 and Energizer EN92. Replace all batteries
at the same time.

►Warranty
Industrial Scientific Corporation's Ventis MX4 portable gas monitors are warranted to be free from defects in material and workmanship
under normal and proper use and service for a period of two years from date of purchase. This warranty includes the sensors, the pump,
and the lithium-ion battery as shipped with the Ventis MX4.
Filters are warranted to be free from defects in material and workmanship for 18 months from date of shipment, or one year from
date of first use, whichever occurs first, except where otherwise stated in writing in Industrial Scientific literature.
Limitation of Liability
THE WARRANTY SET FORTH ABOVE IS STRICTLY LIMITED TO ITS TERMS AND IS IN LIEU OF ALL OTHER
WARRANTIES, GUARANTEES, EXPRESS OR IMPLIED, ARISING BY OPERATION OF LAW, COURSE OF
DEALING, USAGE OF TRADE OR OTHERWISE. INDUSTRIAL SCIENTIFIC MAKES NO OTHER WARRANTIES,
EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE.
INDUSTRIAL SCIENTIFIC MAKES NO OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE.
SHOULD THE PRODUCT FAIL TO CONFORM TO THE ABOVE WARRANTY, BUYER’S ONLY REMEDY AND INDUSTRIAL
SCIENTIFIC’S ONLY OBLIGATION SHALL BE, AT INDUSTRIAL SCIENTIFIC’S SOLE OPTION, REPLACEMENT OR REPAIR OF
SUCH NON-CONFORMING GOODS OR REFUND OF THE ORIGINAL PURCHASE PRICE OF THE NON-CONFORMING
GOODS.
IN NO EVENT WILL INDUSTRIAL SCIENTIFIC BE LIABLE FOR ANY OTHER SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, INCLUDING LOSS OF PROFIT OR LOSS OF USE, ARISING OUT OF THE SALE, MANUFACTURE, OR USE OF
ANY PRODUCTS SOLD HEREUNDER WHETHER SUCH CLAIM IS PLEADED IN CONTRACT OR IN TORT, INCLUDING
STRICT LIABILITY IN TORT.
It shall be an express condition to Industrial Scientific’s warranty that all products be carefully inspected for damage by Buyer upon
receipt, be properly calibrated for Buyer’s particular use, and be used, repaired, and maintained in strict accordance with the
instructions set forth in Industrial Scientific’s product literature. Repair or maintenance by non-qualified personnel will invalidate the
warranty, as will the use of non-approved consumables or spare parts. As with any other sophisticated product, it is essential and a
condition of Industrial Scientific’s warranty that all personnel using the products be fully acquainted with their use, capabilities, and
limitations as set forth in the applicable product literature.
Buyer acknowledges that it alone has determined the intended purpose and suitability of the goods purchased. It is expressly
agreed by the parties that any technical or other advice given by Industrial Scientific with respect to the use of the goods or services
is given without charge and at Buyer’s risk; therefore, Industrial Scientific assumes no obligations or liability for the advice given or
results obtained.

►Ventis MX4 Resource Center

Product documentation.
Online training.
And more!
www.indsci.com/ventis
Contact Information
Industrial Scientific Corporation To locate a nearby distributor of our

1 Life Way products or an Industrial Scientific service
Pittsburgh, PA 15205-7500 center or business office, visit us at
USA www.indsci.com.
Web: www.indsci.com
Phone: +1 412-788-4353 or 1-800-DETECTS (338-3287) Rendez-vous sur notre site
E-mail: [email protected] Web www.indsci.com, si vous voulez
Fax: +1 412-788-8353 trouver un distributeur de nos produits
près de chez vous, ou, si vous recherchez
Industrial Scientific France S.A.S. un centre de service ou un bureau
5 Rue Frédéric Degeorge, CS 80097 Industrial Scientific.
62002 Arras Cedex,
France Besuchen Sie uns unter www.indsci.com,
Web: www.indsci.com um einen Vertriebshändler unserer
Phone: +33 (0)1 57 32 92 61 Produkte oder ein Servicecenter bzw. eine
E-mail: [email protected] Niederlassung von Industrial Scientific zu
Fax: +33 (0)1 57 32 92 67 finden.
英思科传感仪器（上海）有限公司 Para buscar un distribuidor local de

地址：中国上海市浦东金桥出口加工区桂桥路290号 nuestros productos o un centro de servicio
u oficina comercial de Industrial Scientific,
邮编：201206 visite www.indsci.com.
电话：+86 21 5899 3279
传真：+86 21 5899 3280 如需查找就近的产品经销商或 Industrial
E-mail： [email protected] Scientific
网址： www.indsci.com 服务中心或业务办事处，请访问我们的网
服务热线：+86 400 820 2515 站 www.indsci.com。

Tehnic Ventis Mx4

Uploaded by

Document Informationclick to expand document informationTehnic Ventis Mx4 Rom

Document Informationclick to expand document information

Copyright:

Available Formats

Tehnic Ventis Mx4

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tehnic Ventis Mx4

Uploaded by

Copyright:

Available Formats

Multi-gas Monitor

Part Number: 17152357-1

© 2017 Industrial Scientific Corporation 2

Sensor, Sensor Barrier, LCD, and vibrating motor replacement ............................................................ 40

Ventis MX4 Accessories and Parts ......................................................................................................... 47

3 © 2017 Industrial Scientific Corporation

Ventis MX4™ and Ventis™ are trademarks of Industrial Scientific Corporation.

►Warnings and Cautionary Statements

Hazardous Conditions, Poisons, and Contaminants

CAUTION: High off-scale readings may indicate explosive gas concentration(s).

© 2017 Industrial Scientific Corporation 4

Agency-issued Conditions of Use and Warnings

5 © 2017 Industrial Scientific Corporation

SANS 1515-certified units may be used only as follows:

►Ventis MX4 Resources

© 2017 Industrial Scientific Corporation 6

►Ventis MX4 Capabilities

Sensor Number available per Gases Monitored

Oxygen 1 O2 (Oxygen) only

►Unpacking the Monitor

Quantity Item Notes

7 © 2017 Industrial Scientific Corporation

Quantity Item Notes

*Some factory set sensor values subject to user changes.

© 2017 Industrial Scientific Corporation 8

Number Feature Functions

9 © 2017 Industrial Scientific Corporation

Boot-Up Screen Gas Monitoring Screen

Top Row Icons Definition

Warning: indicates monitor or sensor fault.

Gas Cylinder: communicates calibration related information (calibration due, calibration

Low level audio alarm is on.

High level audio alarm is on.

Peak: displayed when peak detection values are viewed.

Lower Explosive Limit. Display variations:

Nitrogen Dioxide (NO2)

© 2017 Industrial Scientific Corporation 10

Percentage Volume: O2 and CH4 measurement unit

Percentage unit for combustible gases; display variations:

Pump: shown anytime an aspirated monitor is in use.

Indicates IrDA communication is in-progress.

Short Term Exposure Limit: communicates STEL values. Display variations:

11 © 2017 Industrial Scientific Corporation

After any over-range alarm, the monitor should

After any negative over-range alarm, the

High Alarm Screen

© 2017 Industrial Scientific Corporation 12

TWA Alarm Screen

STEL Alarm Screen

No Sensor Installed Screen

Sensor Data Fail Screen

Critical Error Screen

13 © 2017 Industrial Scientific Corporation

Note: The nominal flow rate is >200 cc/m (.2

Low Battery Warning Screen

Bump Overdue Screen

Calibration Due Alarm Screen

© 2017 Industrial Scientific Corporation 14

(VTSB-1XY) (VTSB-4XY) (VTSB-2XY) (VTSB-3XY)