Scribd
Upload
769 views

DSC NEO Programming

This document provides instructions for configuring a DSC NEO Power Series alarm panel for communication with a central monitoring station using Contact ID reporting format. Key steps include enabling Contact ID reporting, setting the system account code, selecting events to report, and configuring communication options and zone and output programming. Programming includes setting a momentary keyswitch zone and an output to report armed/disarmed status. Proper testing and confirmation of signals by an experienced installer is advised.

Uploaded by

Jaime Hernandez Hernandez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
769 views

DSC NEO Programming

This document provides instructions for configuring a DSC NEO Power Series alarm panel for communication with a central monitoring station using Contact ID reporting format. Key steps include enabling Contact ID reporting, setting the system account code, selecting events to report, and configuring communication options and zone and output programming. Programming includes setting a momentary keyswitch zone and an output to report armed/disarmed status. Proper testing and confirmation of signals by an experienced installer is advised.

Uploaded by

Jaime Hernandez Hernandez
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DSC NEO Power Series Configuration Manual

(HS2016/2032/2064/2128)

*NOTE: It is advised that an experienced alarm installer programs these panels as further programming may
be needed to ensure proper performance. Full panel testing & signal confirmation must be completed by
the installer.

*IN1 and OUT1 – optional terminals for the remote arm/disarm feature

Wiring the MN01-4G to the Alarm Panel


Enable Contact ID reporting:
Keypad Display Keypad entry Action description
Select: *85555 To enter Programming mode
Select: 301 To enter menu” First phone number”
Select: 001 001 To select first phone number
DFFFFF (or 123456*6*# Enter actual or non-existing number (any number will do, 123456 is example,
previous number) press *6* to enter/exit hex mode in order to fill the rest with ‘F’s)
Select: 383 Enter Communication Options 4
Comm. Option 4: 2# Toggle 2 to OFF, to set the programmable account code in 310 to 4 digits, # saves
Select: 310 To enter menu “System account code”
System account: 000 To enter submenu for the whole system (001, 002… for more partitions)
System account: 1234# Enter 4-digit account number for CMS identification (1234# is an example)
Select: 311 To enter menu “Reporting”
Select: 001 To go to “Alarm restore options’
Toggle receiver#1 *# Press * to select “Y” (yes) – “Alarm/Restore” events are reported to telephone
number 1
Tamper restore: 002 To go to “Tamper/Tamper restore”
Toggle receiver#1 *# Press * to select “Y” (yes) – “Tamper/Tamper restore” events are reported to
telephone number 1
Opening/Closing 003 To go to “Open/Close” events
*## Press * to select “Y” (yes) – “Open/Close” events are reported to telephone
number 1, # to save, # to exit to main menu
Select: 350 To enter “Communicator Alarm Format” options
Enter Data: 001 To select phone number 1
Enter Data: 03# 03 is for Contact ID, # to save (alternatively you can use <> to move in the menu)
Select: 380 Enter First Communication Options
Comms. 1## Toggle 1 to ON, 3 and 4 must be off (DTMF touch-tone dialing, DTMF dialing for
Enabled: all attempts), # to save

Program Keyswitch zone and output:


Keypad Display Keypad Action description
entry
Select: *85555 To enter Programming mode
Select: 001 Enter zone definition menu
Zone definitions * Enter Zone 1 definition
Zone 1 066 To choose Momentary Keyswitch for Zone 1
Momentary KSW ## To exit to main menu
Select: 013 Enter First System Options (to configure Normally Closed Zones)
Toggle 1 * Press * or toggle buttons <> until 1 is ON (all zones are wired as normally closed
circuits with returns to COM terminal)
Toggle Option 1 ## Press ## to exit to main menu
Select: 009 Enter I/O Programming menu
PGM 1 001 To enter PGM 1 subsection
PGM 1 115 To program the output to report Armed/Disarmed status
PGM 1 ## Press ## to exit to main menu

You might also like