2.996/6.
971 Biomedical Devices Design
Laboratory
Lecture 5: Microprocessors I
Instructor: Dr. Hong Ma
Sept. 26, 2007
Analogy: A Complex Machine with Lots of Knobs
Courtesy of NASA.
Microprocessor vs. PCs
• Microprocessors
– Optimized to keep track of time
– MSP430: 16MHz clock Æ 62.5ns timing
• PCs
– Optimized to process large amounts of data
– Windows: ~100Hz timing
– Linux: ~1kHz timing
• Timing accuracy can be leveraged for
measurement functions
Trends in Sensor Architectures
• Single processor Æ distributed processors
The MSP430F2xx Family
• Optimized for low-power and versatility
• Modern architecture, simple to program
• Many peripheral devices – designed to not
require input from the CPU
• Unified address space, no paging
• Device emulates itself
• Inexpensive development tools
• Highly optimized code, designed for C compiler
• Low cost, price >$0.50
MSP430F2xx Architecture
MSP430F2274 Pinout
Port Functions
• Digital input
• Digital output
• Pulled-up / Pulled-down
• Peripheral input / output
• Interrupt on edge
Key: Locate the right
control bits
Memory Map
Von Neuman Architecture
“Software”
(Instructions for
flipping the
switches)
Hardware
Registers
(Switches
and I/O)
Hex Numbers and Memory
MSP430 Memory
• 8-bit addressing
resolution
The Header File (msp430x22x4.h)
• Assigns aliases for registers
• Specific to each processor sub-group
Bit-wise Operators
• Bit-wise “OR”: |
– 1000 | 0101 Æ 1101
• Bit-wise “AND”: &
– 1001 & 0101 Æ 0001
• Bit-wise “NOT”: ~
– ~1001 Æ 0110
• Bit-wise “XOR”: ^
– 1001 ^ 0101 Æ 1100
Assigning Individual Bits
• Assigning all 8-bits at once
– P1OUT = 0xA7
• Assigning individual bits high
– P1OUT |= 0x81
• Assigning individual bits low
– P1OUT &= ~0x81
• Toggling individual bits
– P1OUT ^= 0x81
How to Assign Individual Bits (Better)
• Assign all 8-bits at once
– P1OUT = BIT7 + BIT5 + BIT2 + BIT1 + BIT0
• Assign individual bits high
– P1OUT |= BIT7 + BIT0
• Assign individual bits low
– P1OUT &= ~(BIT7 + BIT0)
• Toggling individual bits
– P1OUT ^= BIT7 + BIT0
Configuring Ports
Main()
{
...
P1DIR |= BIT0 + BIT1 + BIT2 + BIT3 + BIT4 + BIT5;
//Set output mode
P1SEL |= BIT1 + BIT2;
//Output Timer_A1 and Timer_A2
P1REN |= BIT6 + BIT7;
//Enable pull-up/down resistors for BIT6 and BIT7
P1OUT |= BIT0 + BIT6
//Output high on BIT0; Pull-up BIT6
P1OUT &= BIT3 + BIT4 + BIT5 + BIT7
//Output low on BIT3, BIT4, and BIT5; Pull-down BIT7
...
}
Next Topic: Clocks
MSP430 Clocking Scheme
Crystal Oscillators
• Extremely accurate – standard frequency
tolerance = 20ppm
• Many frequencies: 20kHz – GHz
• Real Time Clock: 32.768kHz
• Requires 2 external capacitors
• LFXT1 has integrated capacitors
• Ceramic resonator
– Smaller, cheaper cousin Photo removed due to copyright restrictions.
– Frequency tolerance ~ 0.5%
DCO (Digital Controlled Oscillator)
• 0 to 16 MHz
• Fast start-up <1uS
• ±3% tolerance
• ±6% tolerance over
temperature Images removed due to copyright restrictions.
• Factory calibration in
Flash
• Good enough for
UART
• Application: watch
VLO (Very Low-power Oscillator)
• 0.6µA typical at 25°C
• ~12 kHz (min 4kHz, max 20kHz)
• Can be calibrated using the DCO or XT
• Applications: temperature monitor, blood
glucose sensor
Clock Module
Diagram
Setting Up the Clock Module
Main()
{
...
// 16MHz xtal clock setup: MCLK = 16MHz, SMCLK = 2MHz
BCSCTL1 = XT2OFF | XTS;
// No XT2, LFXT1 in high frequency mode
BCSCTL2 = SELM1 | SELM0 | SELS | DIVS1 | DIVS0;
// MCLK source is LFXT1;
// SMCLK source is LFXT1;
// SMCLK is divided by a factor of 8
BCSCTL3 = LFXT1S1;
// Select integrated capacitors for 3-16MHz resonator
...
}
Clock Ports
Watch-dog Timer (WDT)
• Designed to detect
– Software halting
– Oscillator fault
• Active after device reset
• “Kicking the dog” Æ Reset the WDT
• WDT runs down to 0 Æ Processor reset
• MSP430 WDT:
– Automatically switch clocks after failure
– Password protected
– Can be used as an ordinary timer
MSP430 WDT
WDTCTL = WDTPW + WDTCNTCL;
// Clear WDT
WDTCTL = WDTPW + WDTHOLD;
// Stop WDT
Structure of MSP430 Program
1. Declarations
2. main()
1. Watch-dog timer servicing
2. Setup clocking module
3. Setup peripheral modules
4. Enable interrupts
5. Infinite loop
3. Subroutines
4. Interrupt Service Routines (ISR)
Variable Types
Single-cycle
Type Size
instruction
char 8-bits Yes
int 16-bits Yes
long 32-bits No
float 64-bits No
Number Representation
• One’s Complement • Two’s Complement
//One’s comp. definition //Two’s comp. definition
unsigned char var1 signed char var1
unsigned int var2 signed int var2
Always explicitly define signed / unsigned !!!
Global Variables
//Declarations
unsigned char var
• Global variables not
volatile unsigned char gvar
always updated due to ...
compiler optimization
Main()
{
...
gvar=1;
while(1);
}
#pragma vector=USCIAB0RX_VECTOR
__interrupt void UART_RX(void)
{
gvar=2;
...
}
MSP430F2xx Address Space
• 128kB address space
• Unified memory map, no paging
• F2274: 32kB flash, 1kB RAM
0xFFFF
0xFFFE Reset Vector
0xFFE0 Interrupt Vectors
F2274:
08000h
Unused Flash Memory
Unaddressable
Space
ISR #3
ISR #2
ISR #1
Main()
0x8000
Embedded Programming Styles
• Simple
– Poll for events in main()
• Interrupt-driven
– Code reside in the ISR
– Used for handling a single interrupt source
• Event-driven
– ISR sets flags for events
– main()poll for flags and services them
– Used for handling multiple interrupts sources
Components for Microprocessor
Programming
• ICE – In-Circuit Emulator
– Flash Emulation Tool (FET)
Image removed due to copyright restrictions.
– JTAG
– Spy-Bi-Wire (2-wire JTAG)
• Bootloader
– Rewrite flash via RS232
– Password protected
• IDE – Integrated Development Environment
– Editor, compiler, debugger
• Libraries for each microprocessor
Brownout Detector and SVS
• Brownout detector triggers a POR when supply voltage drops below 1.8V
• SVS (Supply Voltage Supervisor) – Comparator-based (flash) ADC
Timer Related I/O
Communications Ports
Start / Reset Sequence
• PUC (Power Up Clear)
• POR (Power On Reset)
Example C Code
